Embed Size (px)
Citation preview
AAPPPPLLIICCAATTIIOONNVerify accessory fitment at www.indianmotorcycle.com.
BBEEFFOORREE YYOOUU BBEEGGIINNRead these instructions and check to be sure all parts and tools are accounted for. Please retain theseinstallation instructions for future reference and parts ordering information.
KKIITT CCOONNTTEENNTTSS
REF QTY PART DESCRIPTION P/N AVAILABLESEPARATELY
1 1 Module-Garage Door Opener 4015371
IIMMPPOORRTTAANNTTYour Indian Motorcycle® GARAGE DOOR OPENER KIT is exclusively designed for your vehicle. Please readthe installation instructions thoroughly before beginning. Installation is easier if the vehicle is clean andfree of debris. For your safety, and to ensure a satisfactory installation, perform all installation stepscorrectly in the sequence shown.
Instr 9927296 Rev 04 2019-06 Page 1 of 7
P/N 2882132
GGAARRAAGGEE DDOOOORR OOPPEENNEERR KKIITT
Instr 9927296 Rev 04 2019-06 Page 2 of 7
IINNSSTTAALLLLAATTIIOONN IINNSSTTRRUUCCTTIIOONNSSVVEEHHIICCLLEE PPRREEPPAARRAATTIIOONNGGEENNEERRAALL
1. Turn key or ignition switch toOFF position andremove key. If equipped with keyless fob,remove fob from proximity of vehicle.
2. Ensure motorcycle is parked on a flat surface,kickstand is fully extended, and vehicle is stableprior to installation.
GGAARRAAGGEE DDOOOORR OOPPEENNEERR IINNSSTTAALLLLAATTIIOONNFORK MOUNTED FAIRING BIKES
1. Locate grommetA on inside of right sidefairing.
2. Remove grommetA from fairing.
3. Grasp both grommetA and wire harnessbranchB. Disconnect grommet from harness.Discard grommet.
NOTE
Do not let wire harness branchB fall back intohole.
4. Locate harness connection on back of GarageDoor Openerq. Click wire harness branchBinto module.
Instr 9927296 Rev 04 2019-06 Page 3 of 7
5. Insert Garage Door Openerq into hole. Applypressure until module clicks into place.
CHASSIS MOUNTED FAIRING BIKES
1. Apply force to gauge hoodA on underside oftop lip as shown.
2. Apply force until gauge hoodA pops off dashsupport. Remove gauge hood.
3. Remove center grommetB from dash support.
4. Grasp both grommetB and wire harnessbranchC. Disconnect grommet from harness.Discard grommet.
NOTE
Do not let wire harness branchC fall back intohole.
5. Locate harness connection on back of GarageDoor Openerq. Click wire harness branchCinto module.
Instr 9927296 Rev 04 2019-06 Page 4 of 7
6. Insert Garage Door Openerq into hole. Applypressure until module clicks into place.
PROGRAMMING 2-BUTTON HOMELINK
WARNINGGarage door openers, gates, and other devicesmay operate during programming. Ensure peopleand objects are clear of garage door or other
devices to prevent injury or damage to property.
NOTEIt is recommended that a new battery be placed in
the garage door remote for more accurateprogramming.
NOTEGarage door openers manufactured after 1995may be equipped with rolling code protection. Inthis case, a stepladder or other sturdy, safe devicemay be required to reach “Learn” or “Smart”
button on garage door motor.
NOTEPlease note that instructions below apply to
majority of HomeLink use cases. However, thereare applications or compatible systems that
require different instructions.
PPRROOGGRRAAMMMMIINNGG AA BBRRAANNDD NNEEWW HHOOMMEELLIINNKK
1. Position garage door remote 1-3 inches awayfrom HomeLink buttons, keeping indicator lightin view.
2. Simultaneously press and hold both desiredHomeLink button and garage door remotebutton. DO NOT release until HomeLinkindicator light flashes slowly and then changesto solid or rapidly flashing.
NOTESome gate operators and garage door openers
may require you to use “cycling” procedure notedin “Programming an entry gate” section.
3. Press and hold programmed HomeLink buttonand observe indicator light.
a. If indicator light is solid/continuous,programming is complete and your deviceshould activate when button is pressed andreleased.
b. If indicator light blinks rapidly, proceed withfollowing programming instructions for arolling code device.
TIPA second person may make the following steps
quicker and easier.
Rolling Code
4. At garage door opener in garage, locate “learn”or “smart” button. Reference garage dooropener’s manual for location.
5. Press and release “learn” or “smart” button(name and color of button may vary bymanufacturer).
NOTEOnce button is pressed, there are typically about
30 seconds in which to initiate next step.
6. Return to vehicle and press and releaseprogrammed HomeLink button. Repeat rollingcode procedure up to 3 times to completetraining process. HomeLink should now activateyour rolling code equipped device.
7. To program additional HomeLink buttons,repeat this process.
8. Once programmed, both HomeLink and/ororiginal garage door remote may be used toactivate device.
PPRROOGGRRAAMMMMIINNGG AANN EENNTTRRYY GGAATTEE ((FFOORR UU..SS..AA..OOWWNNEERRSS))//PPRROOGGRRAAMMMMIINNGG AA DDEEVVIICCEE IINN CCAANNAADDIIAANNMMAARRKKEETT
1. Position garage door remote 1-3 inches awayfrom HomeLink buttons, keeping indicator lightin view.
Instr 9927296 Rev 04 2019-06 Page 5 of 7
2. Hold HomeLink button continuously, whilesimultaneously pressing and releasing garagedoor remote button at 2 second intervals. DONOT release HomeLink button until indicatorlight flashes slowly and then changes to solid orrapidly flashing.
3. Press and hold programmed HomeLink buttonand observe indicator light.
a. If indicator light is solid/continuous,programming is complete and your deviceshould activate when HomeLink button ispressed and released.
b. If indicator light blinks rapidly, proceed withfollowing programming instructions for arolling code device.
TIPA second person may make following steps
quicker and easier.
Rolling Code
4. At garage door opener/gate, locate “learn” or“smart” button. Reference the garage dooropener/gate’s manual for location.
5. Press and release “learn” or “smart” button(name and color of button may vary bymanufacturer).
NOTEOnce button is pressed, there are typically about
30 seconds in which to initiate next step.
6. Return to vehicle and press and releaseprogrammed HomeLink button. Repeat “press/release” sequence up to 3 times to completetraining process. HomeLink should now activateyour rolling code equipped device.
7. To program additional HomeLink buttons,repeat this process.
8. Once programmed, both HomeLink and/ororiginal garage door remote may be used toactivate device.
RREEPPRROOGGRRAAMMMMIINNGG AA SSIINNGGLLEE HHOOMMEELLIINNKK BBUUTTTTOONNWhen following procedure is performed, buttonswhich already have devices registered to them canbe overwritten:
1. Press and hold desired HomeLink button.
2. After about 20 seconds, HomeLink indicator willstart slowly flashing. While continuing to holdbutton, position garage door remote 1-3 inchesaway from HomeLink buttons, press and holdgarage door remote until indicator light changesto solid or rapid flashing.
NOTESome gate operators and garage door openers
may require you to use “cycling” procedure notedin “Programming an entry gate” section.
3. Press and hold programmed HomeLink buttonand observe indicator light.
a. If indicator light is solid/continuous,programming is complete and your deviceshould activate when HomeLink button ispressed and released.
b. If indicator light blinks rapidly, proceed withinstructions listed in “Rolling Code” section.
4. If you do not program a new device to button, itwill revert to previously held programming.
EERRAASSIINNGG YYOOUURR HHOOMMEELLIINNKK MMEEMMOORRYY ((BBOOTTHHBBUUTTTTOONNSS))
1. Press and hold both buttons for 10 seconds untilHomeLink indicator light changes from solid toflashing indicator.
2. If you sell your vehicle, be sure to eraseHomeLink memory.
SSOOMMMMEERR RROOLLLLIINNGG CCOODDEE PPRROOGGRRAAMMMMIINNGG SSTTEEPPSSNOTE
If you are training two devices, and only one is aSommer, you will need to train Sommer unit first,
and then follow “Reprogramming a singleHomeLink button” instructions for your second
device.
TIPA second person may make following steps
quicker and easier.
1. Press and hold both HomeLink buttons for 20seconds, until LED turns off. HomeLink is nowready to be programmed to Sommer rollingcode garage door opener.
2. At garage door opener in garage, locate “learn”or “smart” button. Reference garage dooropener’s manual for location.
Instr 9927296 Rev 04 2019-06 Page 6 of 7
3. Press and release “learn” or “smart” button(name and color of button may vary by model).
NOTEOnce button is pressed, you have 10 seconds in
which to initiate next step.
4. Return to vehicle and press and releaseprogrammed HomeLink button. Repeat “press/release” sequence up to 3 times to completetraining process. HomeLink should now activateyour Sommer rolling code equipped device.
VVEEHHIICCLLEE RREEAASSSSEEMMBBLLYY
CCHHAASSSSIISS MMOOUUNNTTEEDD FFAAIIRRIINNGG RREEAASSSSEEMMBBLLYY
1. Orient gauge hoodA for reinstallation andmake sure to insert tabs on back of hood asshown.
2. Apply pressure to top of gauge hood until hoodsnaps into place.
AADDDDIINNGG HHOOMMEELLIINNKK WWIIDDGGEETT
NOTEHomeLink widget CANNOT be used to program
doors.
1. Once HomeLink device has been programmed,navigate to rider screen that you would like toadd HomeLink Widget to on Ride Commanddisplay.
2. Tap settings button on lower right corner ofscreen.
3. Locate HomeLink button on left side of screenand drag it over to preferred location on rightside of screen.
Instr 9927296 Rev 04 2019-06 Page 7 of 7
4. Tap DONE in upper right corner of screen orback arrow in lower right corner to get back torider screens.
5. HomeLink widget is now available for use onrider screen for doors you have pre-programmed.
FFEEEEDDBBAACCKK FFOORRMMA feedback form has been created for the installer to provide any comments,questions or concerns about the installation instructions. The form is viewableon mobile devices by scanning the QR code or by clicking HERE if viewing ona PC.
