Gable Platform System for Exterior Operations€¦ · TECHNICAL MANUAL – 06-2010 SETS A - Triangular Bracket (Foldable) Parts Bracket Horizontal (1 pcs) Bracket Diagonal (1 pcs)

06/2010 Technical Manual

MESA - KSK

Gable Platform System for

Exterior Operations

Contents

Introduction

System Description 1 Working Limits 2 Scope of Applications 3

System Overview 4

Sets 12

Dimensions 19

Timbers 21

Part List

Basic System 24 Main System Sets 25 Tie-Shoe Sets 30

Anchor-Shoe Sets 31

Extension Sets 32

Platform-to-Platform Connections 33

General Remarks

Gable Endframe System – KSK

TECHNICAL MANUAL – 06-2010 www.mesaimalat.com.tr

Important Note

Sight-Check

Information

Warning

Remarks

Symbols Used

� All products of MESA should be used

according to the relevant safety regulations of

the state or country in which they are operated.

� Schematic illustrations on this manual give

only basic rules to be applied during assembly,

therefore it does not complete from the safety point

of view.

� MESA products could only be used

according to the Instruction or User Manuals,

any Technical Details given in Documents

provided by MESA.

� Any MESA products could not be combined

with the products of other manufacturers.

� Mesa Imalat reserves the right to make

technical changes in the interests of progress.

© Copyright by MESA Imalat San.ve Tic A.S.-

Ankara-Turkey

Warranty



Warranty Period

� Limited Warranty for two (2) years is

promissed by Mesa İmalat San.ve Tic. A.Ş. for

Steel Face Formworks and Slab Formworks

unless the Operational Conditions described

below are violated.

� This warranty covers defects of steel

material, welding and painting.

� For Hydraulic Cylinders and Hydraulic

Power Units , the limited warranty period is one

(1) year.

Service Life

� Steel Face Formworks and Slab

Formworks, produced by Mesa İMALAT San.ve

Tic.A.Ş., is good for 500 concrete castings

unless The Operational Conditions described

below are violated.

Operational Conditions

� Instruction or User’s Manuals must be

used while Formwork assemblies, accessory

attachements and concrete casting.

� It is not allowed to use hummer,

sedgehummer, cranka and vs that cause physical

demage on Formworks, and also applications of

extra welding, cutting and drilling without permission

of authorities.

� It is not allowed to exceed the Max

Concrete Pressure described in Technical or

User’s Manuals.

� Formwork should be used between + 40 °C

and – 30 °C.

� Formworks should be cleaned after each

application to remove the concrete residues and

active faces should be lubricated with suitable

concrete/metal seperation oil.

� After 250 applications, maintenance should

be done at site.

� This maintenance covers the flatning of

active surface, repainting, welding and rust

control.

� After 500 applications, maintenance should

be done at work shop where the necessary

equipments exist.

� During the storage period, all active

surfaces should be lubricated with suitable oil to

prevent rusting.

� Stock area should be closed area; if it is not

possible, formworks and accessories should be

stocked in open areas by covering them with water

resistant materials.

� Maitenance procedure should be

repeated for each 250 usages after first 500

usages are exceeded.

� For HCP-hydraulic system, the allowable

working pressure must not be exceeded ( 250 bar ).

� All connections between hydraulic

cylinders, hydraulic power units and hydraulic

pipes and must be checked against leakage

before each usage.

� Electrical power supply and connections

must be suitable as written in the ınstruction or

User’s Manuals given by MESA.

Introduction System Description


1


SYSTEM DESCRIPTION

Basic Introduction

MESA-KSK Gable Platform System is designed and

manufactured for exterior working on formwork or any

other construction operations.

It creates a reliable working and walking area for the

crew dealing with all types of formworks or facade

operations.

Basically, system includes two or three foldable

Triangular Brackets, main supporting beam which

hangs on the shoes mounted on the wall and connects

these brackets at the same time, supplementary

connection profiles, post guardrails for safety, steel

girders and timber covers on platform areas.

MESA-KSK Gable Platform is lifted and transferred by

means of cranes.

It provides high degree of reliability and durability in the

range of loading and working limits given in this

manual.

The fundamental advantage of the system is the

versatility on different construction plans.

Scope of Applications

Universal design of MESA-KSK Gable Platform System

gives wide range of application on construction sites.

Before concreting, System assures a powerful bearing

and shoring area for all type of tunnel formworks, wall

formworks and even falseworks

During concreting, a safe, accessible and convenient

working place for concreting crew is achieved by the

System.

Also, for masonry work, brickwork, heavy

cladding,rendering, plastering, and painting, MESA-

KSK Gable Platform System is ready to use.

Standart Lengths

Effective length of MESA-KSK Gable Platform System

having double Triangular Brackets is varying from

1,500 mm to 5,500 mm by adjusting the distance

between two Triangular Brackets and the cantilever in

both sides.

In the Sets having triple Triangular Brackets, effective

length is in between 3,750 mm and 8,750 mm by

adjusting the distance between two Triangular Brackets

and the cantilever in both sides.

Combination of two sets of MESA-KSK Gable Platform

System with double Triangular Brackets gives effective

platform length changing from 6,800 mm to 10,200 mm.

Standart Width

Working area of MESA-KSK Gable Platform System

has 1,800 mm effective width.

By means of Front Extension Set, effective width could

be increased to 2,850 mm.

Introduction Working Limits


2


WORKING LIMITS

Dimensional Limits

Maximum platform length of MESA-KSK Gable

Platform with double Triangular Brackets is 3,750 mm

exluding cantilever parts of the platform.


Platform with triple Triangular Brackets is 6,750 mm

exluding cantilever parts of the platform.

Maximum cantilever platform length on each

sides is 1,135 mm except otherwise stated.


Platform with double Triangular Brackets is 5,500 mm

including cantilever parts of the platform.


Platform with triple Triangular Brackets is 8,750 mm

including cantilever parts of the platform.

Maximum platform length of 2 sets of MESA-

KSK Gable Platform with double Triangular Brackets is

10,200 mm including cantilever parts of the platform.

Maximum width of the effective platform area is

2,850 mm.which is obtained by adding front extension

set. The width of Standart Platform is1,800 mm.

Loading Limits

In minimum span length of double Triangular

Brackets which is 1,000 mm ;

� Maximum Formwork Weight is 2,910 kg.

� Maximum Distributed Load is 490 kg/m².

� Maximum Linear Load is 655 kg/m.

Introduction Scope of Applications


3


SCOPE of APPLICATIONS

KSK-Gable Platform on Tunnel Formwork Applications

Applicability on different combinations

KSK-Gable Platform with access platform on corners

KSK-Gable Platform under Column and Wall Form

KSK-Gable Platform providing necessary safety

KSK-Gable Platform on large application areas

Introduction System Overview


4


Side Guardrail Set* are not included in

Std.System Sets.

Open ends must be kept by Side Guardrail

Set* .

Shoe Set* are not included in Std.System

Sets. Types and quantities of Shoe Set*

are derived according to the solution

requirements.

Types B1 and B2 of Shoe Set* are

described in Section “Sets” of this

Manual.

SYSTEM OVERVIEW

Basic KSK-Gable Platform System

with 2-Triangular Bracket

Basic System

Triangular Bracket – A

Shoe Set* – B1/B2

Support Set – C2

Holder Set – D2

Side Guardrail Set* – F

Guardrail Set – E

Timbers

Safety Timber

Girder Timber

Cover Timber



5


Descriptions on KSK-Gable Platform

System with 2-Triangular Bracket is valid

for The System with 3-Triangular Bracket.

Basic KSK-Gable Platform System

with 3-Triangular Bracket

Timbers

Girder Timber

Guardrail Timber

Cover Timber

Basic System

Triangular Bracket – A

Shoe Set – B1/B2

Support Set – C3

Holder Set – D3

*Side Guardrail Set – F

Std.Guardrail Set – E

Mid.Guardrail Set – G



6


For Lower Extension,

1 set of Telescopic Diagonal,

1 set of Bracket Connector and

1 set of Lower Vertical is required for each

Triangular Bracket .

Support Set is choosen according to the

Nominal Length of KSK-Platform.

Basic KSK-Gable Platform System +

Lower Extension

Lower Extension System

H - Telescopic Diagonal Set

C2/C3 - Support Set

J - Bracket Connector Set

K - Lower Extension Set



7


For Lower Platform,

1 set of Lower Platform and,

1 set of Lower Vertical is required for each

Triangular Bracket .

Support Set is choosen according to the

Nominal Length of KSK-Platform.


Lower Platform

Lower Platform System

Lower Extension Set - K

Support Set - C2/C3

Lower Platform Set - L



8


For Front Extension,

1 set of Front Horizontal and,

1 set of Telescopic Diagonal is required

for each Triangular Bracket .


Front Extension

Front Extension System

Telescopic Diagonal Set - H

Front Extension Set - M



9



Lower Extension +

Front Extension


Lower Extension +

Lower Platform

Lower & Front Extension System

M - Front Extension Set


C2/C3 - Support Set



Lower Extension & PlatformSystem

L - Lower Platform Set

C2/C3 - Support Set


K - Lower Extension set




10



Lower Extension + Lower Platform +

Front Extension

Basic System

Std.Guardrail Set - E

Mid.Guardrail Set - G

Shoe Set - B

Triangular Bracket - A

Support Set - C

Holder Set - D

Extensions








11


Connection of Two Sets of

KSK-Gable Platform System

N - Holder Spacer P - Holder End Set

R -Support Spacer Set S -Support End Set

Introduction Sets


12


SETS

A - Triangular Bracket (Foldable)

Parts

Bracket Horizontal (1 pcs)

Bracket Diagonal (1 pcs)

Bracket Vertical (1 pcs)

Pin-Ø14x100 (1 pcs)

Spring Pin-2.5 (4 pcs)


1

2

3

4

Introduction Sets


13


B1 – Tie-Shoe Set

B2 – Anchor-Shoe Set

Parts

Wing Nut (1 pcs)

Plate (1 pcs)

Shoe-Tie (1 pcs)

Spring Pin-3 (1 pcs)

Shoe (1 pcs)

Parts

E - Std.Guardrail Set (1 set)

M16x100 Bolt (2 pcs)

M16 Washer (2 pcs)

M16 Nut (2 pcs)

Side Guardr.Connector (1 pcs)

Parts

Guardrail Post (1 pcs)

M14x80 Bolt (2 pcs)

M14 Washer (2 pcs)

M14 Nut (2 pcs)

Parts

E - Std.Guardrail Set (1 set)

Mid.Guardr.Connector (1 pcs)

G – Mid.Guardrail Set

F – Side Guardrail Set E - Std.Guardrail Set

Parts

Anchor Screw (1 pcs)

M24 Washer (1 pcs)

M24x70 Bolt (1 pcs)

Anchor Shoe (1 pcs)

Introduction Sets


14


C2 - Support Set ( for 2-Triangular

Bracket System )

C3 - Support Set ( for 3-Triangular

Bracket System )

Parts

C2-Support (1 pcs)



Parts

C3-Support (1 pcs)



N

N

N(mm) Part

1,500 C2-Support (1500)

2,000 C2-Support (2000)

2,500 C2-Support (2500)

3,250 C2-Support (3250)

3,500 C2-Support (3500)

N(mm) Part

2,730 C3-Support (2730)

3,730 C3-Support (3730)

4,730 C3-Support (4730)

6,230 C3-Support (6230)

6,730 C3-Support (6730)

Introduction Sets


15


D2 - Holder Set ( for 2-Triangular

Bracket System )

D3 - Holder Set ( for 3-Triangular

Bracket System )

Parts

D2-Holder (1 pcs)

M14 Nut (4 pcs)

M14 Washer (4 pcs)


Parts


M14 Nut (6 pcs)

M14 Washer (6 pcs)

D3-Holder (1 pcs)

N

N

N(mm) Part

1,500 D2-Holder (1500)

2,000 D2-Holder (2000)

2,500 D2-Holder (2500)

3,250 D2-Holder (3250)

3,500 D2-Holder (3500)

N(mm) Part

2,730 D3-Holder (2730)

3,730 D3-Holder (3730)

4,730 D3-Holder (4730)

6,230 D3-Holder (6230)

6,730 D3-Holder (6730)

Introduction Sets


16




Parts

Front Horizontal (1 pcs)

Timber Connector (2 pcs)

Bracket Connector (1 pcs)



Parts



Telescopic Prop (1 pcs)

Introduction Sets


17





Parts



Lower Vertical (1 pcs)

Parts




Parts


Lower Diagonal (1 pcs)

Lower Horizontal (1 pcs)




Introduction


TECHNICAL MANUAL – 06-2010

N - Holder Spacer Set

R - Support Spacer Set

Parts


Holder Spacer (1 pcs)


Parts


Support Spacer (1 pcs)


18

www.mesaimalat.com.tr

P - Holder End

S - Support End Set

2.5 (2 pcs)

Holder Spacer (1 pcs)

Ø14x115 (2 pcs)

Parts

Spring

Holder End (1 pcs)

Shoe Connector (1 pcs)


2.5 (2 pcs)

Support Spacer (1 pcs)

Ø14x100 (2 pcs)

Parts

Spring Pin

Support End (1 pcs)


Sets

Set

Support End Set

Parts


Holder End (1 pcs)

Shoe Connector (1 pcs)

Ø14x115 (1 pcs)


Support End (1 pcs)

Ø14x100 (2 pcs)

Introduction Dimensions


19


L : Span Length of Triangular Brackets

N: Nominal Platform Length

X: Cantilever Length

P: Platform Length

Dimensions are in mm.

Refer to MESA advisory for other span

lengths listed above.

135mm ≤ X ≤ ( L / 2 )

P = X1 + X2 + L

N = 270 + L N = 270+2L P = X1 + X2 + 2L

For detailed information about cantilever

lengths, refer to section “Loading

Limits” on “User’s Manual”.

DIMENSIONS

Standart Spans

With Double-Triangular Bracket With Triple-Triangular Bracket

X min (mm) X max (mm) P min (mm) P max (mm)

1,500 135 615 1,500 2,460 1,230

2,000 135 865 2,000 3,460 1,730

2,500 135 1,115 2,500 4,460 2,230

3,250 135 1,490 3,250 5,960 2,980

X min (mm) X max (mm) P min (mm) P max (mm)

2,730 135 615 2,730 3,690 1,230

3,730 135 865 3,730 5,190 1,730

4,730 135 1,115 4,730 6,690 2,230

6,230 135 1,490 6,230 8,940 2,980

NOMINAL

PLATFORM

SIZE - N(mm)

SPAN

LENGTH

L (mm)

3-T

rian

gu

lar

Bra

cket NOMINAL

PLATFORM SIZE - N(mm)

SPAN

LENGTH L (mm)

2-

Tri

an

gu

lar

Bra

cket

CANTILEVER LENGTH - X PLATFORM LENGTH - P

CANTILEVER LENGTH - X PLATFORM LENGTH - P

Introduction Dimensions


20


d : Slab Thickness

H : Distance between Ceiling and Tie-Rod

Y :Overall Platform Height

W :Effective Platform Depth

Standart Heights and Depths

Basic System Basic System +

Lower and Front Extension

Wmin=1800 mm Wmax=2825 mm

Ymin=2365 mm Ymax=4275 mm

Ymin 2365

2475

2675

2875

3075

3275

3475

3675

3875

4075

Ymax 4275

Adjustable Height

Range (mm)

Wmin 1800

2125

2295

2475

2645

Wmax 2825

Adjustable Depth Range (mm)

Introduction



Do not use damaged or knotty woods.

P : Platform Length

W : Effective Platform Depth

t : Thickness of Timber Girder

w : Width of Timber Girder

y : Distance between two adjasent Girders

d : Slab Thickness

TIMBERS

Timber Girders

P w

t

P

y

21



List of Platform Lengths “P” are

tabulated in the Section

on this Manual

between two adjasent Girders

Quantity

Dimensions

P y

Wmin

y ≤ (Wmax-Wmin)

Wmin = 1,800 mm

Wmax = 2,825 mm

t (mm)

65

w (mm)

200 d

250 180

Timbers


tabulated in the Section “Dimensions”

this Manual .

Wmax

y ≤ 600 mm

Quantity

1,800 mm 4 pcs.

2,825 mm 6 pcs.

d ≤ 180 mm

180 mm < d

Introduction



P : Platform Length

W : Effective Platform Depth

t : Thickness of Timber Cover

w : Width of Timber Cover


Timber Covers

t

w

W

P w

22





on this Manual

List of Effective Platform Depths “W” are


on this Manual

Quantity

Dimensions

W

PW

min

w

No.of pieces = (P

t (mm)

50

w (mm)200 main

100 filler

Timbers



this Manual .

List of Effective Platform Depths “W” are


this Manual .

P

Wmax

No.of pieces = (P(mm) / 200(mm))

Introduction




P : Platform Length

W : Platform Width

t : Thickness of Guardrail Timber

w : Width of Guardrail Timber

S : Length of Guardrail Timber

Guardrail Timber

S w

t

W

S = W - 100

Side Guardrail Timber

23



List of Effective Platform Depths “W”

and Platform Lengths “P” are tabulated

in the Section

Manual .

ber

Quantity

Dimensions

P

S = P100mm

Side Guardrail Timber Guardrail Timber

Guardrail Timbers

Side Guardrail Timbers

t (mm)

50

w (mm)

150

Timbers

List of Effective Platform Depths “W”

and Platform Lengths “P” are tabulated

in the Section “Dimensions” on this

S = P

Guardrail Timber

Quantity

Guardrail Timbers 4 pcs.

Side Guardrail Timbers 4 pcs.

Part List Basic Systems


24


BASIC SYSTEMS

KSK-BASIC SYSTEM (with 2-Triangular Bracket)

LEGEND ID

Description PART NO PART NAME 1500 2000 2500 3250 3500

D2-Holder M.J.BKSK.1KT….. KSK-HOLDER (See Table) 1 1500 2000 2500 3250 3500

C2-Support M.J.BKSK.1KD….. KSK-SUPPORT (See Table) 1 1500 2000 2500 3250 3500

Bracket Horizontal M.M.KSKH.1K KSK-HORIZONTAL 32.17 2

Bracket Diagonal M.M.KSKD.1K KSK-INSIDE DIAGONAL 10.23 2

Bracket Vertical M.M.KSKV.1K KSK-VERTICAL 25.47 2

Guardrail Post M.D.H401.0K150 401-GUARDRAIL POST (1500) 6.39 2

Pin-Ø14x100 Z.C.PKSK.0E02 KSK-PIN (14x100)-E 0.13 4


Spring Pin-2.5 Z.C.YFR2.0E FR-SPRING PIN (2.5)-E 0.01 10

M14x80 Bolt T.C.GM14.1S0080 HEXAGON BOLT-G (8.8) M14x80 0.14 4


M14 Nut T.D.GM14.1S HEXAGON NUT-G (8.8) M14 0.03 8

M14 Washer T.P.PM14.S WASHER-G (M14) 0.01 8

KSK-BASIC SYSTEM (with 3-Triangular Bracket)

LEGEND ID

Description PART NO PART NAME 2730 3730 4730 6230 6730

D3-Holder M.J.BKSK.1KT….. KSK-HOLDER (See Table) 1 2730 3730 4730 6230 6730

C3-Support M.J.BKSK.1KD….. KSK-SUPPORT (See Table) 1 2730 3730 4730 6230 6730












Support and Holder Lengths (mm)

MESA ID Unit Weight (kg)

NOMINAL PLATFORM SIZE - N (mm)Quantity per Set


Support and Holder Lengths (mm)

NOMINAL PLATFORM SIZE - N (mm)Quantity per Set

Part List Main System Sets


25


MAIN SYSTEM SETS

LEGEND ID

Description PART NO PART NAME







TOTAL WEIGHT 68.49





TOTAL WEIGHT 6.75


Side Guardrail Connector Z.B.H16E.0K1 16E-GUARDRAIL CONNECTOR (Type1) 3.19 1







TOTAL WEIGHT 10.42


Mid.Guardrail Connector Z.B.HKSK.0K2 KSK-MID GUARDRAIL CONNECTOR 3.95 1




TOTAL WEIGHT 10.70

A - KSK-TRIANGULAR BRACKET SET E.M.MKSK.0TB


Quantity per

Set

G - MID GUARDRAIL SET E.M.DHK1.0KQ

E - STANDARD GUARDRAIL SET E.M.DH15.0K

F - SIDE GUARDRAIL SET E.M.DHK1.0KY



26


LEGEND ID


D2-Holder (1500) M.J.BKSK.1KT150 KSK-HOLDER (1500) 21.24 1




TOTAL WEIGHT 21.96





TOTAL WEIGHT 27.82





TOTAL WEIGHT 33.67





TOTAL WEIGHT 42.45





TOTAL WEIGHT 45.37

D2 - KSK-HOLDER SET (1500) E.M.MKSK.0KH215



Quantity per

Set






27


LEGEND ID






TOTAL WEIGHT 37.08





TOTAL WEIGHT 50.28





TOTAL WEIGHT 61.99





TOTAL WEIGHT 79.55





TOTAL WEIGHT 85.40







Quantity per

Set



28


LEGEND ID


C2-Support (1500) M.J.BKSK.1KD150 KSK-SUPPORT (1500) 13.13 1



TOTAL WEIGHT 13.41




TOTAL WEIGHT 17.43




TOTAL WEIGHT 21.46




TOTAL WEIGHT 27.50




TOTAL WEIGHT 29.52

C2 - KSK-SUPPORT SET (1500) E.M.MKSK.0KS215



Quantity per

Set






29


LEGEND ID





TOTAL WEIGHT 23.42




TOTAL WEIGHT 31.89




TOTAL WEIGHT 39.95




TOTAL WEIGHT 52.03




TOTAL WEIGHT 56.03

E.M.MKSK.0KS327C3 - KSK-SUPPORT SET (2730)






Quantity per

Set

Part List Tie-Shoe Sets


30


TIE-SHOE SETS

LEGEND ID


Shoe M.J.AKSK.0K KSK-SHOE 9.57 1

Shoe-Tie (350) Z.S.TQKS.0E035 KSK-SHOE TIE(20FAx350)-E 1.13 1

Spring Pin-3 Z.C.YFR3.0E FR-SPRING PIN (3)-E 0.01 1

Wing Nut Z.S.SKY1.0E23Y10 WING NUT (20F)-E 0.91 1

Plate Z.S.PKP1.0E26 PLATE-10x100x100(26)-E 0.74 1

TOTAL WEIGHT 12.36






TOTAL WEIGHT 12.68






TOTAL WEIGHT 12.85






TOTAL WEIGHT 13.66






TOTAL WEIGHT 14.43






TOTAL WEIGHT 16.10

B - KSK-SHOE SET (350) E.M.JAKS.0K035



Quantity per

Set





Part List Anchor-Shoe Sets


31


ANCHOR-SHOE SETS

LEGEND ID


Anchor Shoe M.J.AKSK.0KB KSK-ANCHOR SHOE 9.32 1

Anchor Screw Z.A.DB50.16024 CONICAL SCREWED ANCHOR-48x160 (M24) 1.40 1



TOTAL WEIGHT 11.13


Quantity per

Set

B - KSK/ANCHOR-SHOE SET (350) E.M.JAKS.0KB160

Part List Extension Sets


32


EXTENSION SETS

LEGEND ID


Telescopic Prop M.J.BKSK.1KBD KSK-TELESCOPIC PROP 18.32 1



TOTAL WEIGHT 18.60

Lower Vertical M.J.BKSK.1KLU KSK-LOWER EXTENSION 11.73 1



TOTAL WEIGHT 11.87

Lower Diagonal M.J.BKSK.2KLB KSK-WALKING PLT.DIAGONAL 18.98 1

Lower Horizontal M.J.BKSK.1KLP KSK-WALKING PLT.HORIZONTAL 7.00 1

Bracket Connector Z.B.JKSK.0K01 KSK-BRACKET CONNECTOR 1.85 1




TOTAL WEIGHT 28.41

Front Horizontal M.J.BKSK.2KLB KSK-WALKING PLT.DIAGONAL 18.98 1

Timber Connector A.M.KSK9.0K KSK-TIMBER CONNECTOR 1.95 2




TOTAL WEIGHT 25.15




TOTAL WEIGHT 1.99

H - TELESCOPIC DIAGONAL SET E.M.MKSK.0KDK


Quantity per

Set

L - LOWER PLATFORM SET E.M.MKSK.0KBG

K - LOWER EXTENSION SET E.M.MKSK.0KBU

J - BRACKET CONNECTOR SET E.M.MKSK.0KDB

M - FRONT EXTENSION SET E.M.MKSK.0KFU

Part List Platform-to-Platform Connections


33


Suffix “-E “ on the Part Name means that

Part is Electro Galvanised.

Suffix “-G “ on the Part Name means that

Part is Hot Deep Galvanised.

For ordering, use MESA ID “PART NO”s

and MESA ID “PART NAME”s of Sets,

Assemblies and any other unique parts.

PLATFORM-to-PLATFORM CONNECTIONS

LEGEND ID


Holder Spacer M.J.BKSK.1KTAA KSK-HOLDER SPACER 21.12 1



TOTAL WEIGHT 21.44

Holder End M.J.BKSK.1KTUA KSK-HOLDER END 19.08 1

Shoe Connector Z.B.JKSK.0K06 KSK-SHOE CONNECTOR 3.58 1



TOTAL WEIGHT 22.67

Support Spacer M.J.BKSK.1KDAA KSK-SUPPORT SPACER 10.35 1



TOTAL WEIGHT 10.63

Support End M.J.BKSK.1KDUA KSK-SUPPORT END 7.61 1



TOTAL WEIGHT 7.75

N - KSK-Holder Spacer SET E.M.MKSK.0KTA


Quantity per

Set

P - KSK-Holder End SET E.M.MKSK.0KTU

E.M.MKSK.0KDUS - KSK-Support End SET

R - KSK-Support Spacer SET E.M.MKSK.0KDA

Notes

