FZ-SM03B-1 1.5~8kg(3.3~17.6lbs)RATED

Scan the QR code with your mobile device follow the link for know more about FEZIBO products.

https://www.facebook.com/Fezibous/?ref=bookmarks

Service@fezibo.com www.facebook.com/Fezibous www.fezibo.com

SafetyHazard Symbols Review:These symbols alert users of a safety condition that demands attention. All users should be able to recognize and understand the significance of the following Safety Hazards if encountered on the product or within the documentation. Children who are not able to recognize and respond appropriately to Safety Alerts should not use this product without adult supervision!

Important! You will need to adjust this product after installation is complete. Make sure all your equipment is properly installed on the product before attempting adjustments. This product should move smoothly and through the full range of motion and stay where you set it. If movements are too easy or difficult or if product does not stay in desi ed positions, follow the adjustment instructions to create smooth and easy movements. Depending on your product and the adjustment, it may take many turns to notice a difference. Any time equipment is added or removed from this product, resulting in a change in the weight of the mounted load, you should repeat these adjustment steps to ensure safe and optimum operation.

Warning: Because mounting surface materials can vary widely, it is imperative that you make sure mounting surface is strong enough to handle mounted product and equipment

Caution:To avoid the potential to pinch cables it is important to follow the cable routing instructions in this manual. Failure to follow these instructions may result in equipment damage or personal injury.

Symbol Signal Word

NOTEA NOTE indicates important information that helps you make be? er use of this product.

A WARNING indicates either potential for property damage, personal injury, or death.

A CAUTION indicates either potential damage to hardware or loss of data and tells you how to avoid the problem.

CAUTION

WARNING

Level of Hazard

Features & Specifi cations

CAUTION: DO NOT EXCEEDMAXIMUM LISTED WEIGHTCAPACITY. SERIOUS INJURY OR PROPERTY DAMAGE MAY OCCUR!

min

10~

max

85m

m

75m

m10

0mm

114m

m

75mm100mm114mm

±180°

±90°

+45°

-45°

min

10~

max

85m

m

100m

m

min

135~

max

415m

m

60mmmin220~max275mm170mm

±180°

±180°

3.3 - 17.6 lbs(1.5 - 8kg)

360°360°

180°

45°

45°

Tools required

Components

Hardware

Parts

O (x1)4mm Allen

Wrench

B (x1)VESA Plate

H (x1)Support Plate

I (x1)Nut

J (x1)Washer

K (x1)Security Nut

L (x2)Bolts

M (x3)Bolts

N (x4)Pad

M4x12mm (x4)M-A

Screws

M4x16mm (x4)M-B

Screws

M5x12mm (x4)M-C

Screws

M5x16mm (x4)M-D

Screws

D5 (x4)M-E

Washer

M-F (x4)M-F

Washer

C (x1)Clamp Base

Support

D (x1)Clamp

E (x1)Cable Clip

F (x1)Long Screw

G (x1)Base Support

P (x1)6mm Allen

Wrench

Q (x1) Wrench

A (x1)Arm

(not included)

Phillips Screwdriver

Choose Mounting Method1

Apply pads (N) to bottom of base to prevent table top from being scratched.

M

O

A

C

N

Secure clamp (D) to upper two holes with bolts (L) using 4mm Allen wrench (O) for desks with a thickness of 10-55mm.

Attach base support cover (E)to clamp base support (C). Tighten the clamp to the desktop using the plastic knob.

Secure clamp (D) to lower two holes with bolts (L) using 4mm Allen wrench (O) for desks with a thickness of 50-85mm.

D

10-5

5mmLO

D

50-8

5mmLO

E

OPTION B: Grommet Base InstallationSlide long screw (F) through the top of the grommet base support (G) and install on base of monitor stand with bolts (M) using 4mm Allen wrench (O). Apply pads (N) to bottom of base.

Position stand on desk with long screw through hole, and secure by using the support plate (H) and washer (J) on underside of the mounting surface, tighten the nut (I) with wrench (Q).

G

M

F

O

N

HJ I Q

ATTACH DISPLAY2OPTION A: Flat Back MonitorAttach the VESA plate (B) to back of monitor and secure with screws (M-A) or (M-C) with washers (M-E). Avoid excessive tightening screws damage the monitor.

OPTION B: Curved Back MonitorAttach the VESA plate (B) to back of monitor and secure with screws (M-B) or (M-D) with washers (M-E) and washers (M-F). Avoid excessive tightening screws damage the monitor.

B

M-AM-C

M-E

M-BM-D

M-EM-F

B

TVTV

TV

Adjust the tension3direction) reduces tension, counter

mount.

Slide the monitor onto the head of swivel arm, install the security nut (K). Make sure the security nut is installed before you rotate the monitor.

K

P

P

Cable Management4For both bottom and upper portion of the spring arm, just slide the cable cover up and away from the spring arm, do not need to take much effort to pull the ends of the cable cover away from the spring arm.

On the bottom portion of the spring arm, insert the cable and slide the cable cover down; On the upper portion of the spring arm, press the tabs on the inside of the cable cover slightly inward and slide down to reattach the cable cover.

1

2

Why choose FEZIBO?Many ergonomic office solutions come at high cost. Our mission is to useinnovation, creativity, and efficiency to produce a more affordable solutionthat doesn't sacrifice quality and is easily accessible to the millions of homeand office workers globally.

If any parts are received damaged or defective, please contact us. We are happy to replace parts to ensure you have a fully functioning product.

For more FEZIBO products, check out our website at: www.fezibo.com

Service@fezibo.com www.facebook.com/Fezibous www.fezibo.com