Upload
truongphuc
View
218
Download
0
Embed Size (px)
Citation preview
FX 220User Instructions
Retail Price Computing Scale
Brisch number 76102-649 Issue 2 07/06/01
ENGLISH *76102-649*
InstallationMake sure that the work surface is firm, steady and free from vibrationand draughts.
To avoid the risk of RSI (Repetitive Strain Injury) it is important toensure that the machine is placed on a surface which is ergonomicallysatisfactory to the user. In cases where usage is prolonged werecommend frequent breaks for the user.
Warnings
Cleaning the scale
For your protection, all mains (110V or 230V) equipment used wheredamp or wet conditions may occur, must be supplied from a correctlyfused source and protected by an approved RCD to BS7071 or BS7288or IEC1008-2-2 BS EN 61008:1995. IF IN DOUBT SEEK ADVICEFROM A QUALIFIED ELECTRICIAN.
To avoid the possibility of electric shock or damage to the machine,always isolate from the mains power supply before carrying out anyroutine maintenance.
Harsh abrasives, solvents, scouring cleaners and alkaline cleaningsolutions, such as washing soda, should not be used especially on thedisplay windows. Under no circumstances should you attempt to wipethe inside of the machine.
The outside of the machine may be wiped down with a clean clothmoistened with water containing a small amount of washing up liquid.
Product variations
Note: Depending on country, some functions may not be available; thelegend on some of the keys may also be different. For example:
Short press Short pressShort press Short press
Or Or
Error messagesIf a persistent error message appears, disconnect thenreconnect the scale to the power supply. If the scale remainsinoperative, contact your authorised service agent.
E 5 Disconnect then reconnect the scale to the power supply.E 10 Battery failure.E 11 Power supply voltage is too high.E 15 Contact your authorised service agent.E 20 Weight error.E 30 Invalid product configuration.E 35E 100 Invalid PLU contents (try re-programming the PLU).E 101 Transaction failed.E 102 PLU write failed.E 103 Tare failed.E 151 Product configuration memory failed.
Error codes:
Contact your authorised service agent.
E 152 User does not have access to this item (in management mode).
E 30
Temporaryerror
Weightunsteady
Balancefailed
Underrange
Overrange
Installing the head-up display optionUsing a flat-bladed screwdriver, remove the blanking plate from theback of the scale.
Carefully insert the plug from the display into the socket at theback of the scale. Replace the blanking plate.
Do not lift the scale by the head-up display or the weighplate.
Attach the display to the scale using the two slottedscrews.
Caution:
Switching on the scale
Connecting to the mains
Warning:
- Plug in the mains cable, replace thecover and weighplate then switch on using the mains ON/OFF switch.
Do not use the mains adaptor if it is damaged.
NiCad
Using batteries
Caution:
- Plug the battery pack into the scale and place thepack into the recess. Replace the cover and weighplate.
To avoid damage to the scale caused by leaking batteries,remove flat or damaged batteries immediately.
When you see the symbol flashing on the display, then you musteither replace the batteries (or recharge the rechargeable batteries).
Using a rechargeable battery pack
Recharging the battery pack
Note:
- Plug the rechargeablebattery pack into the scale and place the pack into the recess. Replacethe cover and weighplate.
- Plug in the mains cable to thebottom of the scale, then switch on using the mains ON/OFF switch.
You can still use the scale while the battery is being charged.
Bleeps
Short press (Press once) Long press (Press and hold)
Using the Clear keyTo clear the last number entered: To clear the entire entry:
Short press Long press
1,5720,260,40
1,5720,000,40
Selecting an alternate price base/Alternative units
00,0000,000,00
Short press
Testing the display/Selecting sleep mode
Short press
1101d0-6-0
Short press
X2Serviceinformation =
Wake up:
Long press Short press
SLEEP
Using the scale
Zeroing the scale - Make sure that the scale is at zero beforeweighing any goods.
Short press
00,0000,000,00
Weighing goods - Place the goods onto the scale and enter the unitprice.
Unit priceShort press
1,5720,260,40
Short press
Multiplying a unit price
Unit priceShort press
1,5720,260,40
1,5720,260,80
Short press Short press
Or
Retaining a unit price
To cancel aunit price:
Unit priceShort press
Repeat until all the goods have been weighed
Short press
Short pressLong press
1,5720,260,40
Item priceShort press
No of itemsShort press
Short press
Multiplying non-weighed items
Repeat until all the goods have been weighed
5
0,36Short press
Long press
Viewing the total Cancelng the total
5
1,80Short press Short press
Item priceShort press
Unit priceShort press
Repeat until all the goods have been weighed
Using the add key
6
1,36Short pressOr
Using tares
Semi-automatic tares
Retaining a tare
Cumulative tare
Keyboard entered tare
Proportional tare
For example, 33 = 3.3%, 205 = 20.5%
Short pressUnit priceShort press
1,5720,260,40
Short pressUnit priceShort press
Repeat until all the goods have been weighed
1,5720,260,40
Short pressUnit priceShort press
% tare X10Short press
1,5720,260,40
Short pressUnit priceShort press
Tare valueShort press
1,5720,260,40
To cancela retained tare:
Short press
Unit priceShort press
1,5720,260,40
Short press
Long press
Repeat until all the goods have been weighed
Short press
Programming a non-weighed PLU hot-keyAssign a unit price to the PLU
You will not be able to programme a PLU hot key if it has alreadybeen changed in management mode.Note:
Item priceShort press Long press
Programming a weighed goods PLU hot-keyAssign a tare to the PLU (if required)
Assign a unit price to the the PLU (if required) Select the PLU key:
Note: For some countries, the tare value canot be saved.
Short press
Or Or
% of tareShort press
Short press Short pressTare valueShort press
Unit priceShort press
Long press
Note: To programmePLUs 10 - 20 refer tomanagement mode.
Short press
Using PLUs
Using the PLU hot keys - For example, PLU .2
0,0000,260,00
Short press
1,5720,260,40
Short pressShort press Short press
1,5720,260,40
Using PLUs 1 - 9 - For example, PLU 7.
Short press Short pressShort press
1,5720,260,40
Using PLUs 10 - 20 - For example, PLU 12.
Navigating management mode
For example, turn the keyboard bleeper off and change the backlighttime to 5 seconds.
Note: Depending on country, some functions may not be available.
Branch Sub-branch
Value
19 .001
Branch ( )19
For Example:
Branch ( )20Sub-branch ( )00Sub-branch ( )01
Sub-branch ( )00
0 .000
19 .011
19 .001
19 .010
20 .004
20 .000
20 .001
Short pressLong press
Short pressShort press
Short pressShort press
Short press
Long press
Long press
Management mode
Entering management mode
Short press
Make a note of thisnumber, cut out andkeep in a safe place.
6 2 3 1Short press
Go to the next branch (long press)Go to next sub-branch (short press)
Go to the previous branch (long press)Go to previous sub-branch (short press)
CSelect value to be changed (short press)Return to Branch 00 (Long press)
Increment the value (short press)Increment the value X10 (long press)
Change the value (short press)After changing a value, you must
go to the next branch to accept the value.Note:
C Exit management mode
Switching the keyboard bleeper on/offGo to branch 19, sub-branch 01
0 = Off1 = On
19 .011
Error bleeperGo to branch 19, sub-branch 03
0 = Off1 = On
19 .031
Target bleepBranch 19, sub-branch 02 - Not applicable for this machine.
Changing the bleeper volumeGo to branch 19, sub-branch 04
0 = Quiet1 = Loud
19 .041
0 = always off1 = 5 seconds2 = 1 minute3 = 5 minutes4 = always on
20 .001
Changing the backlight timeGo to branch 20, sub-branch 00
0 = none1 = 1 minute2 = 5 minutes3 = 30 minutes
20 .011
Changing the sleep timeGo to branch 20, sub-branch 01
0 = Off1 = On
19 .001
Switching the bleeper alarm on/offGo to branch 19, Sub-branch 00
Changing the duration of a 'Long' pressGo to branch 29, sub-branch 00
29 .00200
Enter a value in units of 10 milliseconds (50 -255).For example :200 = 2 seconds150 = 1½ seconds100 = 1 second
Changing the default price baseGo to branch 61, sub-branch 00
0 = 100g1 = kg (lb)
61 .001
Changing a PLU unit priceGo to branch 100 + PLU number, sub-branch 00
You must now select the PLU price base.Note:
For example, PLU 05 Branch, 100 + 5 = 105
Unit price = 2.350 = No unit price
105 .00235
Short press
Changing a PLU tareGo to branch 100 + PLU number, sub-branch 01
Weighed tare: Keyboard entered tare:
For example, PLU 05 Branch, 100 + 5 = 105105 .0150
Short press
Or
Short press Short pressShort press
X2
Changing a PLU price baseGo to branch 100 + PLU number, sub-branch 03
For example, PLU 05 Branch, 100 + 5 = 105
4 = 100g5 = kg (lb)
105 .035
This document contains a general guide only of the product and shall not form any contract unless specifically agreedby Avery Berkel in writing in each case on the Order Acknowledgment. The specification of the products described
herein may vary from time to time and may be altered without notice.
Email: [email protected]@averyberkel.com
Internet: http://www.averyberkel.com
Changing a PLU proportional tareGo to branch 100 + PLU number, sub-branch 02
For example, PLU 05 Branch, 100 + 5 = 105
% tare X10, for example:33 = 3.3%205 = 20.5%
105 .0233