FUSO SEIKI CO., LTD Lumina Automatic Spray Gun FOOD HUMIDIFICATION ST-5 ST-5R ST-6RW STA-1 STA-5N HM-1 HM-3 HM-3W Spraying water to wet …

F U S O S E I K I C O . , L T D

Automatic Spray Gun

ST/HMSERIES

Increased productivity and cost savingsby using a lightweight, compact and powerful spray gun

FUSO SEIKI CO., LTD.

Catalog No.　 CG-05E-1

COOLING

2

L u m i n a A u t o m a t i c S p r a y G u n

COATING

ST-6ST-6RW

Robotic auto paintspraying

MOLDING

ST-5ST-5LST-6HM-1HM-4HM-3HM-5

Spraying mold releaseagents used with die

casting or moldingmachines

ST-5HM-1HM-1WHM-3

Spraying water to cool,release molds

FOOD PROCESSING

ST-6STA-6NHM-6HM-3KW

Spraying alcohols, orscorch prevention

cooking oils

MARKING

ST-5ST-5RST-5SST-6ST-6RST-6S

Spray marking industrialcomponents to

distinguish models ordefect location

SURFACE TREATMENT

ST-5ST-6ST-6WHM-1HM-1W

Spraying waterproof orantistatic agents on

paper or cloth

METAL PROCESS WORK

ST-6HM-3KW

Spraying lubricating oilprior to die cutting

or punching

OIL SUPPLY

ST-5RST-5LHM-3HM-3KWHM-3L

Spraying lubricants ontochains, bearings or

gears

RUST PREVENTION

ST-6HM-6

Spraying rust proof oilsonto steel plates

● Application Examples ●

3


FOOD HUMIDIFICATION

ST-5ST-5RST-6RWSTA-1STA-5NHM-1HM-3HM-3W

Spraying water to wetbread or cookie

surfaces

MIXING

ST-5ST-6STA-5NSTA-6N

Spraying additives

ODOR CONTROL

ST-5HM-1HM-1WHM-4

Spraying deodorizingagents in pig pens,

dump yards, etc

DISINFECTION

ST-5ST-6ST-6RWSTA-1STA-5NHM-1HM-3HM-3W

Spraying disinfectiveliquids in food factories,pig and poultry houses

FACTORY HUMIDIFICATION

ST-5ST-6HM-1HM-1WHM-3HM-4HM-5

Spraying water in printing,paper factories or

mushroom cultivation

ADHESION

ST-5ST-6ST-6RW

Spraying bondingagents onto autointerior materials,

corrugated cartons,heat insulators or

plywood

SURFACE FINISHING

ST-6ST-6W

Sprayingelectroconductive paint

onto interior wall ofcomputer display

housings

POWDER HUMIDIFICATION

ST-5 Spraying water to preventgrain, cement, coal powder

or dust from similar rawmaterials flying into the air

during transportation

BOTTLE MANUFACTURING

HM-1HM-3HM-1WHM-3W

Spraying coating agentsonto bottle surfaces to

prevent scratchingduring shipment

Delivering an incomparable degree of uniform coverage, even when used by anunskilled worker, Lumina Automatic Spray Guns consistently offer unmatched

performance and wide versatility in various fields.

Lumina Spray Guns are in use in a wide range of industries, includingMachine, Machine Tool, Automotive, Auto Parts, Electronics, Molding, Press,

Printing, Paper, Steel, Plastic, Food, Building Material, Textile, Medical, Cosmetic, Glass, and Rubber,for spraying thin to heavy materials

such as Water, Solvents, Thinner, Adhesives, Die Lubricants, Machine Oil,Cutting/Press Oil, Anti-corrosive Paints, Water- and Oil-based Paints, AcrylicPaints, Lacquer, Silicone, Alcohols, Cooking Oils, Flux, and Antistatic Agents.

4


Spray Gun Selection Guide

Do you think that there is little difference betweenspray guns? Actually, each model differs quite a bit,having its own requirements and capabilities. So toselect the most suitable spray gun, a number ofimportant factors must be considered. Among others,these are: i) field to be sprayed, ii) type of liquid,

Selecting an ST-Series Spray Gun to Meet Your Needs

※ See Dimension Chart on page 11.

Compact and easy operating Lumina standard models have been used for a longtime in various industrial fields. A large assortment of spray guns are available tobest meet the needs of a wide range of usage requirements. These form twoproduct lines: the ST-5 series featuring easier use through simplified piping design,and the ST-6 series that delivers a soft and coarse mist plus prevents spray scatter.

iii) quantity of liquid to be sprayed per minute, iv) spaceto be used, v) shape to be sprayed, vi) desired sprayingpattern and width, vii) mist coarseness, and viii) airconsumption allowance. Selection of the most suitablemodel that best meets the requirements, leads togreater productivity.

Standard model for various uses and applications.

Circulating model for spraying sedimentation-type liquids that normally easily settle out. (A pump is required to circulate the liquid.)

Scatter-preventive model allows spraying at lower (than ST-5) air (atomization) pressure, and thus is ideally suited for spraying coating or other oily liquids.

Corrosion-proof stainless steel model especially useful in food processing and medicinal production lines.

Model for spraying approx. twice the area covered by the ST-6 spray gun, on condition that the liquid quantity to be sprayed is less than 50mL/min.

Used for distinguishing small-sized parts/ components by marking and/or coating them.

Long-nosed model for longer range spraying of not easily accessible objects, thus especially well-suited for spraying mold release agents or for cooling aluminum diecast’s components.

Internal channel components and air cap are made of corrosion-protected stainless steel, and these models are especially useful in food processing and medicinal production lines.

Designed specially for making a marking dot, small round pattern of approx. ø 5/64"(2mm), or a narrow line of approx. 1/16"(1mm).

Model for spraying a maximum 25° cone-shaped round pattern, particularly for spraying liquid into a concave container.

ST-5

ST-6RW

ST-5SKST-6SK

STA-1STA-6R

ST-5LST-6L

ST-5RST-6R

ST-6W

STA-5NSTA-6N

ST-6

ST-5C

Both Fan &RoundPattern

Wider AreaFan Pattern

‘Fan’ Pattern Spraying

For wide, oval-shaped pattern coverage. By opening or closing the Pattern Adjuster, it is possible to choose a Round, Fan, or intermediate pattern.

RoundPattern

SmallRoundPattern

Wider AreaRound Pattern

‘Round’ Pattern Spraying

Also known as ‘Cone-shaped’ spraying, coverage is of an approx. 15° conical pattern.

Small Size Series

ST

5

StandardSmall Size Series


Model Name Features SprayPattern

NozzleOrificeø(㎜)

Flow Rate(Water)

mL/min. at3.3'(1m)

Gravity Feed

※Max. SprayPattern Size

from12"(300㎜)Distance

Overall 23/16" (55mm) longcompact design allows for use innarrow spaces. Ideal for applyinglubricants to die cast machinesand during injection molding. Byturning the Pattern Adjuster,pattern and size can be selectedbetween Round, Fan andintermediate positions.

Both fanand round

pattern

0.5

1.0

1.3

2.0

0~60

0~250

0~360

0~600

8"(200㎜)

10"(250㎜)

14"(350㎜)

16"(400㎜)

Used for marking or paintingsmall objects. For sprayinground pattern only.

Roundpattern

0.5

1.0

1.3

2.0

0~70

0~290

0~430

0~650

ø2"(50㎜)

ø23/4"(70㎜)

ø31/8"(80㎜)

ø31/2"(90㎜)

Used for spraying narrow lines orsmall round patterns; Smallestround pattern: ø5/64" (2mm);Thinnest line width: 1/16" (1mm).

Small roundpattern or

narrow line0.5

1.0

0~60

0~160

ø15/8"(40㎜)

ø31/8"(80㎜)

Used for straight spraying ofround patterns at a distancesuch as for die cast parts orcooling a mold; Not suitable forpaints or viscous liquids.

Roundpattern 1.3

2.0

0~170

0~340

ø2"(50㎜)

ø23/8"(60㎜)

Used for spraying highprecipitation liquids; Bycirculating high density liquid,this model prevents liquid fromprecipitating; Single circularpump required.

Both fanand roundpatterns.

0.5

1.0

1.3

2.0

0~70

0~250

0~360

0~600

8"(200㎜)

10"(250㎜)

14"(350㎜)

16"(400㎜)

Air Con-sumption

L/min.(0.3 MPa)

60

80

100

140

35

50

55

85

18

48

100

120

60

80

100

140

The values in the above table are results obtained through tests under the following conditions: Fluid — water; Input fluid pressure — appliedfrom a one meter height with a Gravity Feed Container; Maximum Pattern Width — Measured at a 12" (30cm) distance from the tip of spraynozzle; Input Air Pressure — 43 psi (3kgf/cm2). ※ Due to space limitations — only max. fan width shown for ST-5 & ST-5C models.

ST-5ST-5 Product Line: A Single Air Hose common to PistonOperation and Atomization

The number of hoses to be used in ST-5 models are just two (2): one for air, andanother for liquid supply. A single Air Hose, common to all ST-5 series models, is usedfor Piston operation and for atomization. An air pressure level of 45 to 60 psi (3 to4kgf/cm2) is generally used when spraying with this series models. However, if the airpressure falls below 30 psi (2kgf/cm2), the inside piston does not move backward,preventing liquid from being sprayed. These models are easily maintained andespecially suitable for spraying in confined, narrow spaces.

● In case, Nipple is not required, please specify the order by adding “X” right after the nozzle size.Model No. ST-5-0.5 : With Nipple G1/8 x G1/8 (see cover page) and Hose Joint

(Example, Nozzle size 0.5 mm) ST-5-0.5 X : Without Nipple and Hose Joint

ST-5-*

ST-5R-*

ST-5C-*

ST-5SK-*

ST-5L-*

6


Lower PressureSmall Size Series

Model Name FeaturesSpray

Pattern


Flow Rate(Water)mL/min.3.3'(1m)

Gravity Feed



Used for spraying paints and/orvarious kinds of machine oilswith a lower air pressure so as tominimize oil scattering. Byturning the Pattern Adjuster, thesize of the Round to Fan(intermediate possible) patterncan be selected.

Both fanand round

pattern

0.5

1.0

1.3

2.0

0~60

0~250

0~360

0~600

8"(200㎜)

10"(250㎜)

14"(350㎜)

16"(400㎜)

Used for marking or paintingsmall objects. For sprayinground pattern only.

Roundpattern

0.5

1.0

1.3

2.0

0~70

0~290

0~430

0~650

ø2"(50㎜)

ø23/4"(70㎜)

ø31/8"(80㎜)

ø31/2"(90㎜)

Used for spraying a narrow lineor small round pattern.


narrow line0.5

1.0

0~60

0~160

ø15/8"(40㎜)

ø31/8"(80㎜)

Used for straight spraying ofround patterns at a distance; Notsuitable for paints or viscousliquids.

Roundpattern 1.3

2.0

0~170

0~340

ø2"(50㎜)

ø23/8

(60㎜)

Differences between air pressurefor atomization and spray patternallow for spraying a two timeswider area with less liquid thanthe above ST-6 model; Tworeducing valves are required.

Fan pattern 0.5

1.0

0~30

0~50

8"(200㎜)

12"(300㎜)

Air Con-sumption

L/min.(0.3 MPa)

60

80

100

140

35

50

55

85

18

48

100

120

70

80

The values in the above table are results obtained through tests under the following conditions: Fluid — water; Input fluid pressure — appliedfrom a one meter height with a Gravity Feed Container; Maximum Pattern Width — Measured at a 12" (30cm) distance from the tip of spraynozzle; Input Air Pressure — 43 psi (3kgf/cm2). ※ Due to space limitations — only max. fan width shown for ST-6 model.

ST-6Lower Air Pressure Spraying to Prevent Spray Scatter

In this model series, two separate air hoses (for piston operation & atomization) areused, therefore even a lower air pressure (compared to ST-5 series) of 1.4 psi(0.1kgf/cm2) to 14 psi (1kgf/cm2) can be selected for spraying soft to coarse mistirrespective of the air pressure selected for Piston operation. Air Blow is also availablewhen blowing Air for atomization only after stopping the air for Piston operation.The ST-6RW is especially well-suited for easily coating or painting wider areas orconcave sides. Featuring a special nozzle that emits a spiralling spray stream.

● In case, Nipple is not required, please specify the order by adding “X” right after the nozzle size.Model No. ST-6R-1.0 : With Nipple G1/8 x G1/8 (see cover page) and Hose Joint

(Example, Nozzle size 1.0 mm) ST-6R-1.0 X : Without Nipple and Hose Joint

ST-6-*

ST-6R-*

ST-6W-*

ST-6SK-*

ST-6L-*

7


Stainless Steel Series

STACorrosion-proof Components for Spraying MedicinalLiquid or Flux

The STA series are mainly for spraying flux, fusing agents, and chemicalliquids. All STA models have internal fluid passages constructed of corrosion-proof SUS303 stainless steel and an Air Cap made of SCS13 or SUS303corrosion-proof stainless steel.

● When ordering an STA model, please confirm the suitability since there is still a possibility to corrode, depending on kinds of liquids.● In case, Tube Fitting is not required, please specify the order by adding “X” right after the nozzle size.

Model No. STA-6N-1.3 : With Tube Fitting R1/8 x Inch Hose 1/4(Example, Nozzle size 1.3 mm) STA-6N-1.3 X : Without Tube Fitting



Flow RatemL/min. at

3.3'(1m)Gravity Feed



Spiral air stream produces a finegranular mist covering a sprayangle of approx. 30°, and is ableto also paint or coat side walls(inside of a concave surface) aswell as the bottom. Also, thespiral air stream helps preventthe Air Cap from becomingclogged.

Roundpattern

1.0

1.3

2.0

280

420

670

ø31/2"(90㎜)

ø43/8"(110㎜)

ø47/8"(120㎜)

Air Con-sumption

L/min.(0.3 MPa)

110

130

140

ST-6RW-*



Flow RatemL/min. at

3.3'(1m)Gravity Feed



Components for internal liquidpassages and air cap are madeof SUS303. This model is usedfor spraying mainly medicinalliquids, or other liquids in foodprocessing factories. Forspraying round pattern only.

Roundpattern

0.5

1.0

1.3

2.0

0~70

0~290

0~430

0~650

ø2"(50㎜)

ø23/4"(70㎜)

31/8"(80㎜)

ø31/2"(90㎜)

Internal liquid passages made ofSUS303 stainless steel andSCS13 Air Cap. BothFan/Round, as well asintermediate patterns


0.5

1.0

1.3

2.0

0~60

0~250

0~360

0~600

8"(200㎜)

10"(250㎜)

14"(350㎜)

16"(400㎜)

A high painting/adhesiveefficiency model with lowpressure atomization,constructed of corrosion-proofSUS303 and SCS13 stainlesssteel. Both fan/round, andintermediate patterns.


0.5

1.0

1.3

2.0

0~60

0~250

0~360

0~600

8"(200㎜)

10"(250㎜)

14"(350㎜)

16"(400㎜)

As above, but parts for internalliquid passages and air cap aremade of SUS303. Round patternspraying only.

Roundpattern

0.5

1.0

1.3

2.0

0~70

0~290

0~430

0~650

ø2"(50㎜)

ø23/4"(70㎜)

ø31/8"(80㎜)

ø31/2"(90㎜)

Air Con-sumption

L/min.(0.3 MPa)

35

50

55

85

60

80

100

140

60

80

100

140

35

50

55

85

The values in the above table are results obtained through tests under the following conditions: Fluid — water; Input fluid pressure — appliedfrom a one meter height with a Gravity Feed Container; Maximum Pattern Width — Measured at a 12" (30cm) distance from the tip of spraynozzle; Input Air Pressure — 43 psi (3kgf/cm2). ※ Due to space limitations — only max. fan width shown for STA-5N & STA-6N models.

STA-1-*

STA-5N-*

STA-6N-*

STA-6R-*

8


Standard model for fan pattern spraying.

Has separate air circuits for piston and atomization. This feature makes it possible to spray with lower pressure between 1.4 to 14 psi (0.1 to 1.0 kgf/cm2) to spray coarser particles than HM-1 model.

Model for spraying more than twice the area (wider angle) covered by the above model, regardless of the liquid quantity to be sprayed. When using this model, a pressure liquid tank should be used for supplying liquid.

Twin nozzle headed model allows for spraying the same fan pattern and liquid quantity (adjustable by turning Liquid Adjuster) from both right and left side nozzles at the same time (L/R heads not independently adjustable).

Standard model for spraying round patterns.

Used for spraying fine round patterns, marking dots, or straight lines.

Same lower air pressure model as HM-6. Two separate air hoses model (for piston operation and atomization). Round pattern spraying only.

Mostly used for spraying liquid into the inside wall of concave containers.

Model with a needle nozzle outer diameter of ø1/32" (2mm) and length of 4" (100mm), mainly for use in narrow, confined spaces where ordinary spray guns cannot reach. Other needle nozzle lengths may be special ordered.

Designed to prevent scattering by reducing atomization air pressure so that this model is well suited for spraying all kinds of oily liquids. Suitable for spraying wider round area.

Model always sprays the same round pattern and liquid quantity (adjustable by turning Liquid Adjuster) from both right and left side nozzles at the same time, but not independently adjustable.

HM-1

HM-6

HM-4

HM-3

HM-3P

HM-6R

HM-3W

HM-3L

HM-5

HM-1W

HM-3KW

Wider AreaFan Pattern

Fan Pattern

Double SideSpray

‘Fan’ Pattern Spraying

For wide, oval-shaped pattern coverage. All HM models have no Pattern Adjuster, so they cannot be used for both Fan and Round, or intermediate pattern spraying.

RoundPattern

Wider AreaRoundPattern

Needle NozzleType Round Pattern

Double SideRound Spray

Scatter-preventiveRound Pattern

‘Round’ Pattern Spraying

Cone shaped spraying, wider area and fine particle spraying models. Wider angle models are also available.

※ See Dimension Chart on page 11.

Selecting an HM-Series Spray Gun to Meet Your Needs

Miniaturized, lightweight Lumina models, the epitome of integrated,sophisticated technology, making them easier to use, and most suitable foruse in confined spaces. However, they’re not suitable for spraying paints oreasily precipitated liquids.

Super Mini Size Series

HM

9





Flow Rate(Water)

mL/min. at3.3'(1m)

Gravity Feed

Max. SprayPattern Size


Used for spraying water andlubricants. Fan pattern sprayingonly.

Fan pattern

1.0 0~100 8"(200㎜)

Model for fine granular sprayingover a wider area. Liquid supplyby Pressure Liquid Tank only.Spraying ability higher than thatof two standard units. Fan pattern spraying only.

Fan pattern

1.0 0~300 24"(600㎜)

Double side spraying with twinheaded nozzles. It is possible toadjust the spraying area, butindependent adjustment ofquantity to be sprayed is not.Fan pattern spraying only.

Fan pattern(Double

side) 1.0 0~200 8"(200㎜)

Pinpoint spraying model withø5/64" x 3/8" (ø2mm x 100mm)needle nozzle suitable forspraying liquid in limited, narrowspaces; Various needle lengths

available (desired lengthshould be specified whenordering). Round pattern

spraying only.

Roundpattern

0.7 0~30 ø15/8"(40㎜)

Used for spraying small roundpatterns or narrow lines;


narrow line0.4 0~35 ø15/8"

(40㎜)

Air Con-sumption

L/min.(0.3 MPa)

65

115

115

28

17

The values in the above table are results obtained through tests under the following conditions: Fluid — water; Input fluid pressure — appliedfrom a one meter height with a Gravity Feed Container; Maximum Pattern Width — Measured at a 12" (30cm) distance from the tip of spraynozzle; Input Air Pressure — 43 psi (3kgf/cm2).

Spray distance Pattern Size

3/16"(5mm)3/4"(20mm)

ø5/64 (2mm)ø3/8"(10mm)

HMUltra-compact and Lightweight Models Suitable for usein Confined Space

Exceptionally small spray guns especially for use in limited, confined spacesnot accessible with conventional models. New mini-sized models can bestarted and stopped mechanically or electrically. Except for the HM-6L, asingle common Air Hose (as with ST-5 series) is used. A spraying air pressureof over 30 psi (2kgf/cm2) is required, and if it drops below this value, theinside piston does not move backward, preventing liquid from being sprayed.HM models are not suitable for spraying paints or easily precipitated liquids.

● In case, Nipple is not required, please specify the order by adding “X” right after the model No.Model No. HM-1 : With Liquid Nipple G1/8 x G1/8, Air Elbow Joint R1/8 x G1/8 and Hose Joint(Example) HM-1 X : Without Nipple, Elbow Joint and Hose Joint

HM-1

HM-1W

HM-4

HM-3L

HM-3P

10



Roundpattern



Flow Rate(Water)

mL/min. at3.3'(1m)

Gravity Feed

Max. SprayPattern Size


Standard use model. Roundpattern spraying only.

Roundpattern

1.0 0~200 ø23/8"(60㎜)

Spiralling spray covers a wideround pattern, able to also coatside walls of a concave container(Spiral air stream prevents liquidfrom sticking in air cap, thuskeeping the orifice clear.)

Roundpattern

1.0 0~200 ø4"(100㎜)

As with HM-4, double sidespraying, but Round patternspraying only.

Roundpattern(Double

side) 1.0 0~300 ø23/8"(60㎜)

Used for coarse granularspraying at a lower 1.4 to 14 psi(0.1~1.0kgf/ cm2) air pressurewith independent air supply forpiston operation andatomization; Recommendedwhen coarse mist (not availablewith HM-1 model) is needed, orwhen spraying liquids in alimited, narrow space. HM-6 forfan pattern and HM-6R for roundpattern spraying.

Fanpattern

1.0 0~100 8"(200㎜)

Used especially for sprayinglubricating press oils ordisinfecting agents/alcohols asnozzle design preventsscattering by reducingatomization air within the mainunit. Round pattern sprayingonly.

Roundpattern

1.0 0~60 ø57/8"(150㎜)

Air Con-sumption

L/min.(0.3 MPa)

55

110

110

65

5

The values in the above table are results obtained through tests under the following conditions: Fluid — water; Input fluid pressure — appliedfrom a one meter height with a Gravity Feed Container; Maximum Pattern Width — Measured at a 12" (30cm) distance from the tip of spraynozzle; Input Air Pressure — 43 psi (3kgf/cm2).

55ø23/8"(60㎜)0~2001.0

HM● In case, Nipple is not required, please specify the order by adding “X” right after the model No.

Model No. HM-6 : With Liquid Nipple G1/8 x G1/8, Air Elbow Joint R1/8 x G1/8 and Hose Joint(Example) HM-6 X : Without Nipple, Elbow Joint and Hose Joint

HM-3

HM-3W

HM-5

HM-6HM-6R

HM-3KW

PressureMPa kgf/cm2 psi0.5 5 700.4 4 560.3 3 420.2 2 280.1 1 140.01 0.1 1.4

barFractions are rounded.

11


1/32

"(15

)

3/8"(10.1)

11/16"(17)Liquid Inlet

Air InletRc 1/8

Rp 1/8

3/4"(19) 13/16"(20)

1/2"

(12.

5)

117/32"(39)

5/8"(15)

1/32

"(15

)

AB 11/32"

13/32"(10)

M6 x 1

21/2

"~25

/8"

(63~

66)

FemaleScrew

Rp 1/8

Liquid Inlet

Air Inlet

3/8"(10.1)

11/16"(17)

ø15

Rc 1/8

Rp 1/8

117/32"(39)13/16"(20)

5/8"

(15)

11/4

"(32

)

3/4"(19)

AB 1/2"

(12.5)7/16"(11.5)

ø10

21/2

"~25

/8"(

63~

66)

5/8"

(15)

Rp 1/8

＜ST Series＞● Needle packing is a Perfluoro-chemical O-Ring

(superior in solvent and chemical resistance).● Dimensions shown in drawings at right are

common to all models of ST-5 and ST-6 seriesSpray Guns.

● Air Cap shape differs by model.● Specify desired inner diameter [ø3/8" (10mm)

or ø1/2" (12mm)] of Universal Holder whenordering.

＜HM Series＞● All HM series models have the same

dimensions (see the drawing at right).● Air Cap shape differs by model.

Holder position can be shifted (90°) from the side to the top.

UniversalHolder(360°rotatable)

B

11/2"(38)

23/4

"(70

)

5/8"(16)

17/16"(36)

(C)E

ø10.1

Rp 1/8 Rp 1/8Liquid Inlet Air Inlet

11/4"(32)

A

11/4

"(32

)

F

D

M8 X 1

Rp 1/8

FemaleScrew

A

ø10.1

Rp 1/8

Female ScrewM8 x 1 11

/2"(

38)

11/4

"(32

)

Universal Holder(360° rotatable)

F

Model A B C D E FST-5 23/16"~23/8" 33/8" 23/4" 11/4" 3/16" 11/4"ST-5R 2"~23/16" 27/8" 23/4" 11/64" 3/16" 11/16"ST-5S 23/16"~23/8" 27/8" 23/4" 1" 3/16" 11/4"ST-5L 37/16"~35/8" 27/8" 23/4" 11/64" 3/16" 21/2"ST-5C 23/16"~23/8" 21/2" 23/4" 11/4" 3/16" 11/4"ST-6 23/16"~23/8" 25/16" 23/4" 11/4" 3/16" 11/4"ST-6R 2"~23/16" 17/8" 23/4" 11/64" 3/16" 11/16"ST-6S 23/16"~23/8" 17/8" 23/4" 1" 3/16" 11/4"ST-6L 37/16"~35/8" 17/8" 23/4" 11/64" 3/16" 21/2"ST-6W 23/16"~23/8" 25/8" 23/4" 11/4" 3/16" 11/4"ST-6RW 2"~23/16" 17/8" 23/4" 11/64" 3/16" 11/16"STA-1 2"~23/16" 27/8" 23/4" 11/64" 3/16" 11/16"STA-5N 23/16"~23/8" 33/8" 23/4" 11/4" 3/16" 11/4"STA-6N 23/16"~23/8" 29/16" 23/4" 11/4" 3/16" 11/4"STA-6R 2"~23/16" 21/8" 23/4" 11/64" 3/16" 11/16"

inch

Model A B C D E FST-5 55~60 85 70 ø31 4 32ST-5R 50~55 73 70 ø26 4 27ST-5S 55~60 73 70 ø25 4 32ST-5L 87~92 73 70 ø26 4 64ST-5C 55~60 64 70 ø31 4 32ST-6 55~60 59 70 ø31 4 32ST-6R 50~55 47 70 ø26 4 27ST-6S 55~60 47 70 ø25 4 32ST-6L 87~92 47 70 ø26 4 64ST-6W 55~60 67 70 ø31 4 32ST-6RW 50~55 47 70 ø26 4 27STA-1 50~55 73 70 ø26 4 27STA-5N 55~60 85 70 ø31 4 32STA-6N 55~60 65 70 ø31 4 32STA-6R 50~55 53 70 ø26 4 27

mm

Model A BHM-1 11/4" 29/32"HM-1W 11/4" 29/32"HM-4 17/8" 15/16"HM-3L 53/4" 43/4"HM-3P 17/16" 11/8"HM-3 15/16" 5/8"HM-3W 15/16" 5/8"HM-5 15/16" 10/16"

HM-6R 15/16" 5/8"HM-3K 15/16" 5/8"

inch

HM-6 11/4" 29/32"

Model A BHM-1 31.5 23HM-1W 31.5 23HM-4 48 24HM-3L 147 120HM-3P 37 28.5HM-3 24 15.5HM-3W 24 15.5HM-5 33 16.5

HM-6R 24 15.5HM-3K 24 15.5

mm

HM-6 31.5 23

■ Due to product modification or improvement, specifications are subject to change without notification.■ All metric dimensions have been converted to the nearness value in feet (') and inches ("), therefore these values are less accurate.

Dimension Chart

ST-5

ST-6

HM-1HM-3

HM-4HM-5

B

Rp 1/8Rp 1/8

G 1/8

Air Inlet forPiston operation

Liquid InletAir Inlet foratomization5/8"(16)

17/1

6"(3

6)

11/4"(32)

E

Spray Gun : WeightModel No. g

ST-5-0.5 280ST-5-0.5X 265ST-6-0.5 285ST-6-0.5X 260HM-1 130HM-1X 105

X: Without Joints and Nipples

12 Catalog No. CG-05E-1 ©2005 Printed in Japan

Using the right automatic spray gun in any spraying process providesmaximum efficiency and increases productivity. Consult FUSO SEIKI or an

authorized LUMINA agent/dealer to avail yourself of our accumulatedexperience, knowledge of precision processing technology and strict quality

control, all of which can help you realize cost savings through maximizedefficiency and increased productivity.

FUSO SEIKI CO., LTD.12-17, Honkomagome 6-chome, Bunkyo-ku, TOKYO,113-0021 JAPAN

Tel : +81-3-3947-1334Fax: +81-3-3947-1319Internet: http://www.fusoseiki.co.jpE-mail: [email protected]

Documents

FUSO SEIKI CO., LTD Lumina Automatic Spray Gun FOOD HUMIDIFICATION ST-5 ST-5R ST-6RW STA-1 STA-5N HM-1 HM-3 HM-3W Spraying water to wet …