Fujitsu Siemens Lifebook S6410 Disassembly Instructions

Disassembly Instructions

Pages 32

Version V1.0/

21. Jun. 2007

Disassembly Instruction for LIFEBOOK S6410

Contents

Disassembly Instruction for LIFEBOOK S6410 ........................................................................................ 1 Contents.................................................................................................................................................... 1

Notes on installing and removing boards and components ............................................................... 2 Removing the battery ........................................................................................................................ 3 Removing the FlexiBay module......................................................................................................... 4 Removing the dust filter .................................................................................................................... 5 Removing the service door................................................................................................................ 6 Removing the memory (RAM)........................................................................................................... 7 Removing the hard disk (HDD) ......................................................................................................... 8 Removing the mini card modules ...................................................................................................... 9 Removing the Bluetooth module (BT) ............................................................................................. 10 Removing the Trusted Platform module (TPM)............................................................................... 11 Removing the fan............................................................................................................................ 12 Removing the heatsink.................................................................................................................... 13 Removing the processor (CPU) ...................................................................................................... 14 Removing the strip cover................................................................................................................. 15 Removing the keyboard................................................................................................................... 17 Removing the heat plate.................................................................................................................. 18 Removing the LCD display.............................................................................................................. 19 Removing the top cover................................................................................................................... 21 Removing the fingerprint, touchpad and touchpad buttons ............................................................. 23 Removing the modem module......................................................................................................... 24 Removing the USB board ............................................................................................................... 25 Removing the audio board .............................................................................................................. 26 Removing the 3rd WLAN antenna ................................................................................................... 27 Removing the mainboard ................................................................................................................ 28 Removing the FlexiBay connector board......................................................................................... 30 Removing the Multi-Card reader module......................................................................................... 31 Final disassembly of the lower case................................................................................................ 32


2

Notes on installing and removing boards and components

!

Before removing a module, first switch off the notebook and disconnect from the power supply or batteries.

The workstation must be correctly configured in accordance with ESD regulations!

Only use professional tools! ● Switch the notebook off and pull the power plug out of the mains socket.

● Remove the battery.

● Take care when you use the locking mechanisms on the battery and any other component.

● Never use sharp objects such as screwdrivers, scissors or knives as leverage to remove covers.

Boards with electrostatic sensitive devices (ESD) are identifiable by the label shown.

When you handle boards fitted with ESDs, you must, under all circumstances, observe the following points:

● You must statically discharge yourself before working with boards (e.g. by touching a grounded object).

● The equipment and tools you use must be free of static charges.

● Remove the power plug from the mains supply before inserting or removing boards containing ESDs.

● Always hold boards with ESDs by their edges.

● Never touch pins or conductors on boards fitted with ESDs.


Removing the battery ► Close the LCD screen so that it locks into place

► Unplug the mains adapter from the mains socket.

► Disconnect all cables connected to the notebook.

► Turn your notebook over and place it on a stable, sturdy, flat surface. If necessary, place an anti-slip cloth on this surface to prevent the notebook from being scratched.

► Slide the battery catch in the direction of the arrow (yellow arrow) as far as it will go. ► Slide the locking device in the direction of the arrow (red arrow) and hold it in place. ► While holding the slider (red arrow), fold the battery back.

► Remove the battery from the notebook (in the direction of the green arrow).


4

Removing the FlexiBay module Preliminary steps required

● Removing the battery

► Slide the ejector lever carefully down in the direction of the arrow (yellow arrow) as far as it will go and hold it in place.

► Pull the module out of the module bay.


Removing the dust filter Preliminary steps required


► Carefully push the mounting clip in the direction of the arrow (yello arrow).

► Pull out the dust filter.


6

Removing the service door Preliminary steps required:

● Removing the battery ● Removing the FlexiBay module ● Removing the dust filter

► Remove the seven M2.0x4 mm screws (marked with yellow ovals in the diagram).

► Pull the service door carefully in the direction of the arrows (yellow arrows) and lift it off.


Removing the memory (RAM) Preliminary steps required:


► Remove the two M2.0x4 mm screws (marked with yellow circles).

► Pull off the cover from the notebook in the direction of the arrow (yellow arrow).

► Carefully push the two mounting clips outwards (yellow arrows)

The memory module will snap upwards.

► Pull the memory module out of its location.

► Do the same in case of two installed memory modules.


8

Removing the hard disk (HDD) Preliminary steps required:

● Removing the battery ● Removing the FlexiBay module ● Removing the dust filter ● Removing the service door

► Pull the hard disk by the pulling aids as far as it will go in the direction of the arrow (yellow arrow).

► Lift the hard disk and remove it from the hard disk compartment.

► Remove the two M3.0x3.5 mm screws (marked with yellow circles).

► Slide the hard disk out of the cover.


Removing the mini card modules Preliminary steps required:


► Unplug the antenna cables marked with the yellow oval (2 for UMTS / 3 for WLAN / none for Intel Turbo Memory).

► Unplug the connector marked with the green oval.

► Unlock the modules by pressing the two metal latches (marked with yellow circles).

The module snaps up (see right mini card).

► Pull the modules out of the slot in direction of the red arrow.


10

Removing the Bluetooth module (BT) Preliminary steps required:


► Remove the two M2.0x3 mm screws (marked with red circles).

► Disconnect the Bluetooth antenna cable (marked with yellow circles) and take it out.

► Open the connector lock by pulling the lock into the direction of the red arrows.

► Lift the Bluetooth module off.

► Open the connector lock (red oval) and pull the cable out of the connector.


Removing the Trusted Platform module (TPM) Preliminary steps required:


► Remove the M2.0x3 mm screw (marked with yellow circle).

► Lift the module out of the connector to remove it.


12

Removing the fan Preliminary steps required:


► Remove the two screws M2.0x4 mm (yellow circles).

► Disconnect the power plug (red oval).

► Lift the fan off carefully.


Removing the heatsink Preliminary steps required::

● Removing the battery ● Removing the FlexiBay module ● Removing the dust filter ● Removing the service door ● Removing the fan

► Remove the four M2.0x4 mm screws (marked with yellow circles).

► Lift the heatsink to remove.


14

Removing the processor (CPU) Preliminary steps required::

● Removing the battery ● Removing the FlexiBay module ● Removing the dust filter ● Removing the service door ● Removing the fan ● Removing the heatsink

► Open lock in the direction of the yellow arrow.

► Lift the processor carefully to remove.


Removing the strip cover Preliminary steps required:


► Remove the four M2.0x3 mm screws (yellow circles) in the battery compartment.

► Press the plastic lugs (yellow arrows) to the rear until they unclick.

► Turn the notebook over.

► Carefully fold the two covers away from the strip cover (yellow arrows).

► Turn the Notebook over and fully open the LCD Display.


16

► First use a plastic tool to carefully lift the strip cover on both sides, then lift it up and out.

! Take care not to break the speaker cable. It is very short.

► Disconnect the speaker cable and remove the strip cover.


Removing the keyboard Preliminary steps required:

● Removing the battery ● Removing the FlexiBay module ● Removing the strip cover

! The keyboard is stuck to the heat spread with several adhesive strips.

► Carefully lift the keyboard up and use only small steps to remove the adhesive without damaging the heat spreader.

► Open the connector locks (yellow arrows) and disconnect the keyboard cable from the socket.

► Take the keyboard out of the notebook.


18

Removing the heat plate Preliminary steps required:

● Removing the battery ● Removing the FlexiBay module ● Removing the strip cover ● Removing the keyboard

► Remove the four M2.0x4 mm screws (marked with red circles).

► Lift the heat plate off.


Removing the LCD display Preliminary steps required:

● Removing the battery ● Removing the FlexiBay module ● Removing the dust filter ● Removing the service door ● Removing the mini card modules ● Removing the strip cover ● Removing the heat plate ● Removing the keyboard

► Carefully loose the antenna cables (grey, blue, black, yellow orange) of the Wlan and UMTS module and the cable for the

microphone (black / white twisted).


!

When assembling the unit please keep in mind to pull the cables through the brackets (see white arrows).


20

► Remove the two M2.5x4mm screws (yellow arrow).

► Disconnect the LCD cable (either 1 or 2 – depending on the LCD) marked with green oval.

► Remove the two M2.5x6mm screws (yellow circles).

► Lift off the display and carefully pull the antenna cables through the housing opening.


Removing the top cover Preliminary steps required:

● Removing the battery ● Removing the FlexiBay module ● Removing the dust filter ● Removing the service door ● Removing the RAM modules ● Removing the mini card modules ● Removing the strip cover ● Removing the heat plate ● Removing the keyboard ● Removing the LCD display

► Remove the 13 M2.5x6 screws (yellow circles).

► Remove the two M2.0x2.5mm screws (green circles).



22

► Open the connectors lock (yellow oval) and disconnect the touchpad cable from the socket.

► Lift off the top cover.


Removing the fingerprint, touchpad and touchpad buttons Preliminary steps required:

● Removing the battery ● Removing the FlexiBay module ● Removing the dust filter ● Removing the service door ● Removing the RAM modules ● Removing the mini card modules ● Removing the strip cover ● Removing the heat plate ● Removing the keyboard ● Removing the LCD display ● Removing the top case

► Remove the two M2.0x3.5mm screws (yellow circles).

► Open connector locks (red ovals) and remove the touchpad / fingerprint sensor cable.

► Lift the module up and out.

i

If it is necessary to replace the touchpad, then you will need to replace the entire upper part of the housing (without fingerprint).


24

Removing the modem module Preliminary steps required:

● Removing the battery ● Removing the FlexiBay module ● Removing the dust filter ● Removing the service door ● Removing the RAM modules ● Removing the mini card modules ● Removing the strip cover ● Removing the heat plate ● Removing the keyboard ● Removing the LCD display ● Removing the top case

► Remove the two M2.0x3mm screws (yellow circles) and lift the modem module out of the connector.

► Disconnect the cable (yellow oval).


Removing the USB board Preliminary steps required:

● Removing the battery ● Removing the FlexiBay module ● Removing the FlexiBay module ● Removing the dust filter ● Removing the service door ● Removing the RAM modules ● Removing the mini card modules ● Removing the strip cover ● Removing the heat plate ● Removing the keyboard ● Removing the LCD display ● Removing the top case

► Open connectors lock and remove USB cable (yellow ovals).

► Remove the M2.0x4mm screw (marked with green circle).

► Lift the board up and out.


26

Removing the audio board Preliminary steps required:


► Open connectors lock and remove the cable (yellow oval).

► Remove the two M2.0x3mm screws (green circles).

► Slantwise lift the board up and out.


Removing the 3rd WLAN antenna Preliminary steps required:


► Remove the M2.0x3mm screw (marked with red circle).

► Lift the antenna module up and lift it out.

!

When assembling the unit please keep in mind to pull the cables through the brackets (see white arrows).


28

Removing the mainboard Preliminary steps required:

● Removing the battery ● Removing the FlexiBay module ● Removing the dust filter ● Removing the service door ● Removing the RAM modules ● Removing the mini card modules ● Removing the Bluetooth module (BT) ● Removing the Trusted Platform module (TPM) ● Removing the strip cover ● Removing the keyboard ● Removing the heat plate ● Removing the LCD display ● Removing the top case ● Removing the modem module ● Removing the USB board ● Removing the audio board ● Removing the 3rd WLAN antenna

► Remove the two M2.0x4mm screws (yellow circles).

► Open the two connectors lock and remove the cables (green ovals)

► Remove the cable for the USB board (red oval).


► Remove the 2 hexagonal, size 5 bolts (yellow circles) in the direction of the yellow arrows.

► Lift the mainboard and take it out.


30

Removing the FlexiBay connector board Preliminary steps required:

● Removing the battery ● Removing the FlexiBay module ● Removing the dust filter ● Removing the service door ● Removing the RAM modules ● Removing the mini card modules ● Removing the Bluetooth module (BT) ● Removing the Trusted Platform module (TPM) ● Removing the strip cover ● Removing the keyboard ● Removing the heat plate ● Removing the LCD display ● Removing the top case ● Removing the modem module ● Removing the USB board ● Removing the audio board ● Removing the 3rd WLAN antenna ● Removing the mainboard

► Remove the two screws marked with the yellow circles and lift the board out of the connector.


Removing the Multi-Card reader module Preliminary steps required


► Remove the two screws marked with yellow circles.

► Open connectors lock (marked with green ovals) and disconnect the flexprint cable.

► Lift the module out of the connector.


32

Final disassembly of the lower case Preliminary steps required:


► For finally disassembling the unit, remove the parts marked with the yellow arrows.

Documents

Fujitsu Siemens Lifebook S6410 Disassembly Instructions