Installation Guide - English

Fujitsu Converged Network Adapter (CNA)Fujitsu PCNA EP OCe14401 1x 40GbHardware and Software Installation Guide

Edition September 2015

Copyright and Trademarks

Comments… Suggestions… Corrections…The User Documentation Department would like toknow your opinion of this manual. Your feedback helpsus optimize our documentation to suit your individual needs.

Feel free to send us your comments by e-mail to manuals@ts.fujitsu.com.

Certified documentation according to DIN EN ISO 9001:2008To ensure a consistently high quality standard anduser-friendliness, this documentation was created tomeet the regulations of a quality management system which complies with the requirements of the standardDIN EN ISO 9001:2008.

cognitas. Gesellschaft für Technik-Dokumentation mbHwww.cognitas.de

Copyright © 2015 Fujitsu Technology Solutions GmbH.

All rights reserved.Delivery subject to availability; right of technical modifications reserved..

All hardware and software names used are trademarks of their respective manufacturers.

PCNA EP OCe14401 1x 40Gb Page 3

Table of Contents

Table of Contents

1. Introduction................................................................................................................ 4

Major Features..................................................................................................................... 4

Prerequisites ....................................................................................................................... 6

Adapter Identification ......................................................................................................... 6

2. Hardware Installation................................................................................................. 7

Preparing the Adapter for Installation............................................................................... 7

Installing the Adapter.......................................................................................................... 8

Attaching Devices ............................................................................................................... 8

Fujitsu PCNA EP OCe14401 1x 40Gb Accessories .................................................... 10

Applying Power ................................................................................................................. 10

Viewing the LEDs ...............................................................................................................11

3. Software Installation................................................................................................ 12

Initial operating system installation .............................................................................. 12

Maintenance................................................................................................................. 12

Emulex Management Utility OneCommand Manager (OCM) ...................................... 12

Enabling or Disabling the Secure Firmware Feature ................................................... 12

4. References................................................................................................................ 14

Specifications .................................................................................................................... 14

FCC and Regulatory Notices............................................................................................ 15

Declarations of Conformity .............................................................................................. 17

Laser Safety Notice........................................................................................................... 18

1. Introduction Major Features

1. IntroductionThis manual describes the Fujitsu PCNA EP OCe14401 1x 40Gb PCI-Express adapter for Enhanced Ethernet Fabric of multi-protocol PCI-Express adapters for 10 and 40 Gigabit/sec (Gb/s) Enhanced Ethernet (EE) fabric. This adapter provides ethernet networking and iSCSI functionality, as well as Fibre Channel over Ethernet (FCoE) functionality for convergence of Fibre Channel (FC) traffic onto 40 Gb/s EE fabric.

The PCNA EP OCe14401 is available as a full-featured universal converged network adapter (UCNA) that supports NIC, iSCSI, and FCoE.

This adapter supports NIC single root I/O virtualization (SR-IOV) and are fully compliant to the PCI Express CEM Specification Rev. 3.0/2.0/1.1. UCNAs combine two major functional components: a 10 Gigabit networking MAC and an FC IOC to interface with a unified lossless Ethernet switch. Adapters serve as a common interface for both storage and IP traffic retaining familiar FC and networking software stacks, OS drivers, and management. The supported PCIe connector is an x8.

Illustrations in this manual are only examples. The actual hardware may vary.

Figure 1-1 Fujitsu PCNA EP OCe14401 1x 40Gb Adapter

Major Features Eight PCIe functions, partially configurable to NIC, iSCSI, or FCoE personalities

with offload features

Eight-lane (x8) Generation 3 PCIe interface at 8GT/s, 5GT/s, or 2.5GT/s (auto-negotiated with system)

Low-profile PCIe form factor PCBA: 6.600 inches by 2.713 inches

PCNA EP OCe14401 1x 40Gb Page 4

1. Introduction Major Features

Comes with low I/O bracket installed for low-profile cards; optional full height I/O bracket is included in lose delivery unit.

Support for 10 GbE SFP+ optical or Direct-Attach Copper (DAC) connectors

SFF-8431 Enhanced Small Form Factor Pluggable Module SFP+ compliant

External volatile memory: 2Gb/4Gb DDR3 SDRAM technology

On-board flash memory: The flash is 128Mbit with a SPI interface. The flash contains the vital product data (VPD) and Boot BIOS images. You can update the flash with Emulex utilities.

Interoperates with existing FC SAN infrastructures – switches, arrays, SRM tools (including Emulex utilities), SAN practices, and so forth

Unified Ethernet-to-FC SAN connectivity provided by an FCoE switch

Comprehensive array of NIC, iSCSI and FCoE operating system drivers, including support for Windows, Linux, and VMware

Parts and construction compliant to the European Union Directive of Restriction of Hazardous Substances (RoHS), and similar regulatory requirements for other countries.

Protocol-specific capabilities

- NIC capabilities include:

- NDIS 5.2, 6.0, and 6.2-compliant Ethernet functionality

- IPv4/IPv6 TCP, UDP checksum offload

- IPv4/IPv6 Receive Side Scaling (RSS)

- IPv4/IPv6 Large Receive Offload (LRO)

- IPv4/IPv6 Large Send Offload (LSO)

- Programmable MAC addresses

- Up to 128 MAC/VLAN addresses

- Support for hash-based multicast MAC address filters

- Support for hash-based broadcast frame filters per port

- VLAN insertion and extraction

- Jumbo packet support up to 9200 bytes

- iSCSI capabilities include:

- Full iSCSI protocol offload

- Header, data digest (CRC) and PDU

- Direct data placement of SCSI data

- Up to 4K outstanding commands (iSCSI CNA only mode)

- Up to 512 offloaded iSCSI connections (iSCSI CNA only)

- iSCSI initiator and concurrent initiator/target modes

- Support for multipath I/O

- T10 PI support for end-to-end data integrity (for target mode drivers)

- FCoE capabilities include:

- Hardware offloads of Ethernet TCP/IP and concurrent iSCSI and FCoE

- ANSI T11 FC-BB-5 support

PCNA EP OCe14401 1x 40Gb Page 5

1. Introduction Prerequisites

- Programmable World Wide Name (WWN)

- Support for FIP and FCoE Ether Types

- Concurrent logins (RPI): up to 8K per ASIC (FCoE CNA only mode)

- Open exchanges (XRI): up to 4K per ASIC (FCoE CNA only mode)

- FCoE initiator and target modes

- Supports up to 255 NPIV interfaces

Prerequisites PCI Express 3.0/2.0/1.1 compliant systems: x8 lane at up to 8 Gb/s per lane.

Adapter IdentificationEach adapter ships with several numbers clearly marked on the board. Fujitsu recommends recording these numbers before installation.

IEEE address – a unique 64-bit identifier used for system configuration

World Wide Name (WWN) – derived from the IEEE address; the FC industry uses the WWN for FC connectivity.

Serial number – assigned by Emulex and used when communicating with Emulex

Note: The adapter has two IEEE addresses and two WWNs, one for each port.

PCNA EP OCe14401 1x 40Gb Page 6

2. Hardware Installation Preparing the Adapter for Installation

2. Hardware InstallationThe PCNA EP OCe14401 adapter can be connected to fiber optic cables (used with embedded optical transceivers) or DAC cables. Additional information for these cable connections and other installation procedures are described in the following sections.

Preparing the Adapter for InstallationBefore installing the adapter, you should perform the following steps:

1. Turn off the computer and unplug it.

2. Remove the computer case.

Note: The adapter comes with a low-profile PCIe bracket installed. A low profile bracket is included in the box with the adapter.

3. For the PCNA EP OCe14401 adapter, if you want to change the bracket to a full height version, follow steps 4–12; otherwise, proceed to “Installing the Adapter” on page 8.

4. Remove the mounting bracket screws from the top of the adapter (see circles in figure 2-1).

Figure 2-1 Removing the Bracket

5. Remove the bracket and store it for future use.

6. Align the new mounting bracket tabs with the holes in the adapter.

Note: Be careful not to push the bracket past the transceiver or RJ-45 housing's grounding tabs. Ensure the light emitting diodes (LEDs) are properly aligned with the holes in the bracket.

7. Re-install the screws that attach the adapter to the bracket.

PCNA EP OCe14401 1x 40Gb Page 7

2. Hardware Installation Installing the Adapter

Installing the AdapterTo install the adapter:

1. Turn off and unplug the computer.

2. Remove the computer case.

3. Remove the blank panel from an empty PCIe bus slot. See “Preparing the Adapter for Installation” on page 7 to change the brackets if needed. Otherwise, proceed to “Attaching Devices” on page 8.

Note: Place the adapter into an empty PCIe x8 or x16 slot. Make sure that the adapter is in an appropriate PCIe slot that does not interfere with other components or case to prevent damage to the adapter.

4. Insert the adapter into the empty x8 or x16 PCIe bus slot. Press firmly until the adapter is seated.

5. Secure the adapter's mounting bracket to the case with a panel screw or clip.

6. Replace the computer case and tighten the case screws.

The adapter is now installed in the server and is ready for device attachment.

Attaching DevicesThere are two types of cables that can be connected to the adapter:

Fibre optic cable

DAC cable

An adapter does not allow normal data transmission on either optical or copper links, unless it is connected to a compatible optical or copper interface connection. The cable and connector specifications are listed in section “Supported cables” on page 8.

Note: Optic 40GBASE-SR4 short wave lasers with MPO type connectors support up to 100m for OM3 and 150m for OM4 respectively on MMF cables.

Supported cables

QSFP Direct Attached Twinax Copper interface

QSFP Break-Out Twinax cable for 4x 10Gb- 40GBASE-SR short wave lasers with MPO type connector

To attach devices to the adapter:

1. Connect the appropriate cable to the adapter.

When connecting an optical cable, ensure the cages have optical transceivers installed in them (see Figure 2-2).

PCNA EP OCe14401 1x 40Gb Page 8

2. Hardware Installation Attaching Devices

Figure 2-2 Installing an Optical Transceiver

Once the optical transceivers are installed, insert the optical cable into the LC connectors on the adapter (see Figure 2-3).

Figure 2-3 Connecting a Fiber Optic Cable

When connecting a DAC cable, ensure the QSFP+ cages do not have optical transceivers installed in them. After confirming there are no optical transceivers installed, insert the DAC transceiver into the QSFP+ cage on the adapter (see Figure 2-4).

PCNA EP OCe14401 1x 40Gb Page 9

2. Hardware Installation Applying Power

.

Figure 2-4 Connecting a DAC Cable

2. After the appropriate cable is connected to the adapter, connect the other end of the cable to a suitable device, such as a Top of Rack (TOR) EE switch.

After the device is connected to the adapter, you are ready to apply power to the computer. See “Applying Power” on page 10.

Fujitsu PCNA EP OCe14401 1x 40Gb AccessoriesTable 2-1 provides model number, name, interface and required quantities if you want to order additional or replacement transceivers, or cables.

Applying PowerTo apply power:

1. Verify that the adapter is securely installed in the computer.

2. Verify that the correct device is attached.

3. Plug in and turn on the computer.

4. Observe the boot banner for Power On Self Test (POST) results.

Table 2-1 Emulex OneConnect Accessories

Model Number Model Name Quantity Interface

S26361-F5539-E140/-L140

PCNA QSFP+ MMF MODULE FOR OCE14401

OC40-SR4-OPT-1 1 pc 40GBASE-SR4 (short reach optical)

PCNA EP OCe14401 1x 40Gb Page 10

2. Hardware Installation Viewing the LEDs

Viewing the LEDsEach port connector has two LEDs: an amber LED and a green LED.

Amber LED (Link)

On (constantly) = Link up

Off = Link down

Green LED (Ethernet Activity)

Blink = Activity on the Ethernet link

Off = No activity on the Ethernet link

Figure 2-5 Optical and DAC Adapter LED Indicators

Note: If you connect the controller to 4 10Gb switch ports via a breakout cable, the LEDs indicate only the status of the first cable.

PCNA EP OCe14401 1x 40Gb Page 11

3. Software Installation

3. Software Installation

Initial operating system installationFor installing the operating system please use "ServerView Installation Manager (SVIM)". In connection with installing the operating system, all necessary software components to administrate the controller will be installed automatically. For more information about SVIM, see http://manuals.ts.fujitsu.com.

MaintenanceFor maintaining and updating your controller, please use ServerView Management Software e.g. ServerView Operation Manager, ServerView Update Manager or ServerView Update Manager Express For further details, see http://manuals.ts.fujitsu.com.

Drivers and Utilities to administrate and update your controller can be found at http://support.ts.fujitsu.com

or use the ServerView Update DVD. For information please read in manual

FUJITSU Software ServerView SuiteLocal System Update for PRIMERGY Servers

which also can be found at http://support.ts.fujitsu.com.

Emulex Management Utility OneCommand Manager (OCM)For Windows operating systems the Emulex Management Utility OneCommand Manager (OCM) will be installed by SVIM automatically.

Under Linux operating systems a manual installation is necessary. Link to:

http://support.ts.fujitsu.com/productselect.asp?lng=com&Level1=20966&lnid=3

Enabling or Disabling the Secure Firmware FeatureThe PCNA EP OCe 14401 1x 40Gb adapter has a jumper (J3) that enables or disables the Secure Firmware feature as required.

To ensure that the firmware on this adapter cannot be changed offline (using an ISO flash file), leave the jumper block installed on the relevant jumper pins (Secure Firmware enabled). To allow offline firmware updates on this adapter, remove the jumper block from the pins (Secure Firmware disabled); the jumper must be replaced after the offline update is completed. To update the firmware using a tool such as the OneCommand Manager application, boot utilities, or Elxflash utilities, there is no need to remove the jumper – the Secure Firmware feature can remain enabled.

Figure 3-1 shows the locations of the Secure Firmware jumper J3.

PCNA EP OCe14401 1x 40Gb Page 12

3. Software Installation

Figure 3-1 Secure Firmware Jumper Location J3

1 Secure Firmware Flash enabled

2 Secure Firmware Flash disabled

PCNA EP OCe14401 1x 40Gb Page 13

4. References Specifications

4. References

SpecificationsTable 4-1 PCNA EP OCe14401 Adapter Specifications

Parameter Range

Physical Dimensions Low-profile form factor, 6.600 inches by 2.713 inches, and accommodates both the full-height and low-profile bracket.

Power Requirements PCNA EP OCe14401 adapter:

Typical:

- 9.96 Watts (optical, 40GbE)

- 8.63 Watts (passive, 40GbE direct-attach cable)

Worst case:

- 12.987 Watts (optical, 40GbE)

- 11.636 Watts (passive, 40GbE direct-attach cable)

Airflow 200 lf/min (minimum)

Temperature 0°C to 55°C (operating)

-40°C to 70°C (non-operating)

Note: Operating the adapter in higher temperatures and/or lower air flow may result in premature failures.

Humidity Operating: 10% to 90% RH, non-condensing, 22°C wet bulb

Non-operating: 5% to 95% RH, non-condensing, 22°C wet bulb

Agency Approvals for PCNA EP OCe14401 adapter

• Class 1 Laser Product per DHHS 21CFR (J) & EN60825-1 when equipped with approved optical devices

• UL recognized to UL60950-1 2nd Edition

• cUR recognized to CSA 22.2, No. 60950-1-07

• TUV certified to EN60950-1:2006 +A11 +A1 +A12

• FCC Rules, Part 15, Subpart B, Class A

• Industry Canada, ICES-003, Class A

• EMC Directive 2004/108/EC (CE Mark)

EN55022:2010, Class A

EN55024:2010

• Australian EMC Framework (C-Tick Mark)

AS/NZS CISPR22:2009 +A1, Class A

• Japan VCCI, Class A

• Taiwan BSMI, Class A

• Korea MSIP, Class A (KN22 /KN24) referencing latest MSIP and RRL notices

• BSMI Class A, consisting of CNS 13438:2006 (complete edition)

• RoHS Compliant (Directive 2011/65/EU)

• China RoHS compliant

Vibration, peak acceleration 0.25g (5 Hz to 500 Hz)

(Sweep Rate = 1 octave/min.)

PCNA EP OCe14401 1x 40Gb Page 14

4. References FCC and Regulatory Notices

FCC and Regulatory Notices

OCe14000-series Adapters

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

Responsible Party:

Jeff Benck, President and Chief Executive Officer

Emulex Corporation (714) 662-5600

3333 Susan St. Costa Mesa, CA. 92626 USA

Note: This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense. The reader is cautioned that changes or modifications made to the equipment not expressly approved by Emulex could void the user's authority to operate this equipment. The above statement applies to products marketed in the USA.

This class A digital apparatus meets all requirements of the Industry Canada (IC) Interference - Causing Equipment Standard (ICES-003).

Cet appareil numérique de la classe A respecte toutes les exigences du règlement sur le matériel brouilleur du Canada. CAN ICES-3 (A)/ NMB-3 (A)

Notice for Japan and Translations (VCCI)

Translation:

This is a Class A product. If this equipment is used in a domestic environment, radio interference may occur, in which case, the user may be required to take corrective action. VCCI—A.

PCNA EP OCe14401 1x 40Gb Page 15

4. References FCC and Regulatory Notices

Notice for Taiwan and Translations (BSMI)

Translation:

This equipment is a Class A ITE, and operation of this equipment in a residential area is likely to cause harmful interference, in which case users will be required to correct the interference at their own expense.

Notice for South Korea and Translations (KCC)

Translation:

Sellers and users of this equipment take note that this equipment is EMC approved for Class A industrial use, and as such is not intended for residential use.

PCNA EP OCe14401 1x 40Gb Page 16

4. References Declarations of Conformity

Declarations of Conformity

PCNA EP OCe14401 Adapter

This equipment complies with CISPR22/EN55022 Class A.

WARNING: This is a class A product. In a domestic environment, this product may cause radio interference requiring the user to take adequate measures.

Note: Changes or modifications not expressly approved by Emulex Corporation, including the use of non-Emulex approved optical transceivers, could void the user's authority to operate this equipment.

PCNA EP OCe14401 1x 40Gb Page 17

4. References Laser Safety Notice

Laser Safety NoticeFujitsu products incorporating optical laser transceivers contain Class 1 laser devices, which comply with DHHS/CDRH 21CFR Sub-chapter J, and the international laser safety standard EN/IEC 60825-1. Class 1 laser devices are not considered to be hazardous.

The use of non-Fujitsu approved optical transceivers, or transceivers which do not comply with the Class 1 radiation performance requirements defined in DHHS/CDRH 21CFR Sub-chapter J and IEC 60825-1, may expose the user to hazardous laser radiation, and such devices should not be used with Emulex products.

PCNA EP OCe14401 1x 40Gb Page 18