Upload
cineversum
View
229
Download
0
Tags:
Embed Size (px)
DESCRIPTION
Upgrades the Blackwing projector to work with passive 3D glasses
Citation preview
www.cineversum.com
Part. No.: R599825
FSST Passive 3D Kit for Blackwing (3D models)
ASSEMBLY AND CALIBRATION
Ref: R1048214-222 Rev: 01
2 R599825 - Passive 3D Kit
ChangesCineversum provides this manual ’as is’ without warranty of any kind, either expressed or implied, including but notlimited to the implied warranties or merchantability and fitness for a particular purpose. Cineversum may makeimprovements and/or changes to the product(s) and/or the program(s) described in this publication at any timewithout notice.This publication could contain technical inaccuracies or typographical errors. Changes are periodically made to theinformation in this publication; these changes are incorporated in new editions of this publication.
CopyrightAll right reserved. No part of this document may be copied, reproduced or translated. It shall not otherwise berecorded, transmitted or stored in a retrieval system without the prior written consent of Cineversum.
GuaranteeCineversum provides a guarantee relating to perfect manufacturing as part of the legally stipulated terms ofguarantee. On receipt, the purchaser must immediately inspect all delivered goods for damage incurred duringtransport, as well as for material and manufacturing faults. Cineversum must be informed immediately in writing ofany complaints.If the purchaser or third party caries out modifications or repairs on goods delivered by Cineversum, or if the goodsare handle incorrectly, in particular if the systems are commissioned operated incorrectly or if, after the transfer ofrisks, the goods are subject to influences not agreed upon in the contract, all guarantee claims of the purchaser willbe rendered invalid. Not included in the guarantee coverage are system failures which are attributed to programs orspecial electronic circuitry provided by the purchaser, e.g. interfaces. Normal wear as well as normal maintenanceare not subject to the guarantee provided by Cineversum either.The environmental conditions as well as the servicing and maintenance regulations specified in this manual mustbe complied with by the customer.
TrademarksBrand and product names mentioned in this manual may be trademarks, registered trademarks or copyrights oftheir respective holders. All brands and product names mentioned in this manual serve as comments or examplesand are not to be understood as advertising for the products of their manufactures.
TABLE OF CONTENTS
1.0 INSTALLATION .............................................................................................................. 41.1 The optional Passive 3D Kit .............................................................................................................. 41.2 Download the Passive 3D Kit setup TEST PATTERNs .................................................................... 41.3 Passive 3D screen that maintains light polarization .......................................................................... 41.4 Attach the Passive 3D Kit to the projector ........................................................................................ 41.5 Connect the Passive 3D Kit to the projector...................................................................................... 6
2.0 POSITION AND ALIGNMENT ..................................................................................... 72.1 STEP 1: Adjust the Passive 3D modulator gross position ................................................................. 72.2 STEP 2: Moir artifacts and Focus .................................................................................................... 92.3 STEP 3: Vertical and Horizontal Tilt setting (important) ................................................................ 10
Lens Flare.......................................................................................................................... 112.4 STEP 4: Check the 3D performances .............................................................................................. 132.5 STEP 5: Ghosting Black-over-White levels (optional).................................................................... 13
3.0 LED TROUBLESHOOT ............................................................................................... 143.1 LED standard functions ................................................................................................................... 143.2 Issues and LED troubleshooting ...................................................................................................... 14
4.0 MAINTENANCE AND CLEANING............................................................................ 14
R599825 - Passive 3D Kit 3
1.0 INSTALLATION
1.0 INSTALLATION
1.1 The optional Passive 3D Kit
The Blackwing (3D-compatible) projector is now available with a Passive 3D modulator for 3D enthusiasts andspectators how are 3D sensitive. Thanks to the use of the passive 3D technology and the lightweight, flicker-freeglasses, the stereoscopic picture is 50% brighter than with the active sets but also smoother and more natural to theeyes. The Passive 3D Kit is installed in front of the projector. Avoid direct sun light and make sure to install it in aplace with a good ventillation.Make sure to have a passive 3D compatible screen installed before proceeding to the Passive 3D Kit install.To make the installation easier, use this guide together with the original Cineversum Passive 3D Test Patternspackage available on www.cineversum.com.
1.2 Download the Passive 3D Kit setup TEST PATTERNs
This manual refers to TEST PATTERNs that can be downloaded directly from the official Passive 3D Kit web page,in the download section. These patterns are in PNG format and they may be used in addition to this document tomake easier and faster the install.If you choose to use these TEST PATTERNs, you will need to display them at 1920x1080 pixels resolution on theprojector. To do so, you probably can load them on a USB key directly inserted into your Blu-Ray player or simply byconnecting a computer to the projector, using a DVI to HDMI cable.
1.3 Passive 3D screen that maintains light polarization
In order to enjoy the best quality 3D images, you need a polarization preserving screen. Such a screen is generallycalled “silver screen” and it is specially designed for 3D projection. Cineversum has developed and optimized aspecial screen fabric for both 2D projection and passive 3D projection: the “Passive 5D screen”. It is a low gain andhigh extinction ratio fabric that you can order together with your Passive 3D Kit.
1.4 Attach the Passive 3D Kit to the projector
a) Use the 2 wheels to attach the Modulator to the U-shape support.
Fix the Modulator to the U-shape support using the 2 wheels.
Visit Cineversum’s web site: http://www.cineversum.com to download the TEST PATTERNs.
If your screen is not manufactured and tested for passive 3D use, you might experience uncomfortable andblurry 3D images with a high level of crosstalk, which will greatly impact on the perception of thestereoscopic effects.
4 R599825 - Passive 3D Kit
1.0 INSTALLATION
b) Use the 6-pan screw (M5x10) to fix the U-shape support.
Fix the U-shape support to the mounting plate using the 6-pan screw.
c) Use the 2 screws (M4x20) to fix the Passive 3D Kit to the projector.
Attach the Passive 3D Kit to the projector using the 2 M4x20 screws.
M5x10
M4x20
R599825 - Passive 3D Kit 5
1.0 INSTALLATION
1.5 Connect the Passive 3D Kit to the projector
Use the Jack 3.5mm stereo to VESA miniDin-3 cable to connect the “Sync” input of the Passive 3D Kit to the “3DSynchro” signal output located at the back of the projector.
Connect the 3.5mm jack termination to the SYNC input of the Passive 3D Kit
Connect the VESA Mini-DIN 3 termination connector to the 3D Synchro at the back of the projector.
SYNC
AUX
SYNC
from Passive 3D Kit
3D SYNCHRO (VESA miniDIN 3)
6 R599825 - Passive 3D Kit
2.0 POSITION AND ALIGNMENT
2.0 POSITION AND ALIGNMENT2.1 STEP 1: Adjust the Passive 3D modulator gross position
Position the projector equipped with the Passive 3D Kit at the desired projection distance. Then adjust the correctzoom, offset and focus to fit the screen. These adjustment are made by using the Zoom, Focus and the vertical /horizontal Shift of the projector.
Adjust the lens Offset and Zoom until the picture fills the screen.
Adjust the picture Focus
Once the picture is correctly centered and fills the screen, please use the TEST PATTERN 1b (full green patternwith 16:9 written on it) to adjust the modulator correctly in front of the projector lens. The correct position for themodulator is reached when the light path uses the maximum surface of the LCD window, without blocking light inthe borders. To do so, place the Passive 3D Kit at the maximum distance possible and moves it toward the projectoruntil the light path is centered and entirely contained into the LCD window.
ZOOM
BACK
TEST LIGHT
ASPECT HIDE
PC
HDMI 1
VIDEO
HDMI 2
S-VIDEO
COMP.
LENS
STAND BY
MENU
CINEMA3
USER2 THX
PICTURE MODE
INPUT
CINEMA1
CINEMA2
NATURAL STAGE DYNAMIC
USER1
ON
LENS
ZOOM
FOCUS
BACK
TEST LIGHT
ASPECT HIDE
PC
HDMI 1
VIDEO
HDMI 2
S-VIDEO
COMP.
LENS
STAND BY
MENU
CINEMA3
USER2 THX
PICTURE MODE
INPUT
CINEMA1
CINEMA2
NATURAL STAGE DYNAMIC
USER1
ON
LENS
R599825 - Passive 3D Kit 7
2.0 POSITION AND ALIGNMENT
Tighten the 2 screws A when the distance between the modulator and the projector lens is correct.
Then adjust the vertical position to center the light path into the Passive 3D Kit as described below.
Tighten the 2 wheels B when the light path is at the center of the modulator.
If the projector uses a large zoom (<2.0 throw ratio distance), the modulator will be fixed nearer to theprojector. If the projector uses a small zoom (>2.0 throw ratio distance), the modulator will be located fartherfrom the projector.
Correct position The modulator is too nearThe modulator is too far
A
A
B
B
Correct vertical position
8 R599825 - Passive 3D Kit
2.0 POSITION AND ALIGNMENT
2.2 STEP 2: Moiré artifacts and Focus
Depending on the size of the screen, the screen fabric may -or may not- interact with the projector pixels anddevelop some color banding interferences. In order to remove them completely, you may alter slightly the projectorfocus. Use the TEST PATTERN 2b or a bright picture (White, Cyan by example) to set the correct projector Focus..
Alter slightly the picture focus to eliminate the moiré artifacts.
Moiré artifacts
FOCUS
BACK
TEST LIGHT
ASPECT HIDE
PC
HDMI 1
VIDEO
HDMI 2
S-VIDEO
COMP.
LENS
STAND BY
MENU
CINEMA3
USER2 THX
PICTURE MODE
INPUT
CINEMA1
CINEMA2
NATURAL STAGE DYNAMIC
USER1
ON
LENS
R599825 - Passive 3D Kit 9
2.0 POSITION AND ALIGNMENT
2.3 STEP 3: Vertical and Horizontal Tilt setting (important)
Ideally, the Passive 3D Kit should be perfectly perpendicular to the light path, that means if you use the projectoroffset to center the picture into your screen, you will need to set an initial tilt on the Passive 3D modulator.
Set the initial tilt of the Passive 3D Kit perpendicularly to the light path.
B
B
Initial tilt angle
Initial tilt angle
10 R599825 - Passive 3D Kit
2.0 POSITION AND ALIGNMENT
Lens FlareAlso, due to internal reflections from the Passive 3D modulator, you may see a noticeable lens flare on high contrastpictures, typically credits at the end of a movie, or using TEST PATTERNS 3a and 3b.Use TEST PATTERN 3a to check if there is a ghosting text at the top and bottom of the screen.
To completely remove Lens Flare, apply an additional Vertical andHorizontal tilt to the modulator. These additional tilts should not exceed 7°.
Use TEST PATTERN 3b to perfectly identify the lens flare location.
To completely remove the lens flare, tilt the Passive 3D Kit in order to change the lens flare position and to move itout of the screen. Preferably move it outside the screen through one of the four circles number 8, 13, 78 or 83. To doso, you will apply a vertical tilt and horizontal tilt. This step is required to obtain a ghost free and highly contrastedpicture.
It is recommended to always use a small amount of tilt to remove the potential reflections, called lens flares.Do not use more than 7° of tilt. Above this mark, there is too much tilt and a visible vertical ghosting willappear and may distract spectators.
The lens flare may be identified as a very bright, disc-shaped reflection of a portion of the original picture asshown in the above picture. By changing the Passive 3D Kit tilt, the lens flare will move around the pictureand be more noticeable.
-7°
+7°Initial tilt angle
Additional tiltfor Lens Flare
R599825 - Passive 3D Kit 11
2.0 POSITION AND ALIGNMENT
Set an additional Vertical and Horizontal Tilt to move the lens flare outside the screentoward one of the circles number 8 or 13 or 78 or 83
If the tilt required to pull out the lens flare through circle 8 is above 7°. Select a different circle: 78 byexample. Make sure that the additional Vertical and Horizontal tilts never exceed 7°.
C
Horizontal tilt
Vertical tilt Tighten screw C when done
12 R599825 - Passive 3D Kit
2.0 POSITION AND ALIGNMENT
2.4 STEP 4: Check the 3D performances
To check the 3D performances of the Passive 3D Kit, you can use TEST PATTERN 4b or directly by viewing a 3Dprogram. To use the TEST PATTERN 4b, please follow the steps below:
• Browse, select and display the TEST PATTERN 4b
• Go into the projector menu and select the Side-by-Side 3D mode
• Put the passive 3D glasses on
When closing the right eye, the R-squares should be barely visible.
2.5 STEP 5: Ghosting Black-over-White levels (optional)
The TEST PATTERNS 5a and 5b will reveal the ghosting overlapping black-over-white level. This setting has aminor performance hit on global 3D performances. Additionally, if the lens flare has been correctly pushed out of thescreen, there should be only a residual clear coloration into the black pattern. You can adjust into the projector menuthe black level and white level to reduce the overlapping coloration.Make sure when doing this setting that the central steps remain in grey shades.
The overlapping black-over-white may be lightly colored butthe central bar must remain in grey shades to obtain the best 3D performances.
Note that the projector needs to warm up at least 20 min. to obtain a cross-talk free image.
Once STEP 5 is completed, you can set in the projector menu the 3D mode back to “Auto”.
EMPTY AREAS WHEN CLOSING RIGHT EYE
R599825 - Passive 3D Kit 13
3.0 LED TROUBLESHOOT
3.0 LED TROUBLESHOOT3.1 LED standard functions
3.2 Issues and LED troubleshooting
4.0 MAINTENANCE AND CLEANINGAvoid direct sun light and water contact with the Passive 3D Kit. This device must be in a place with goodventillation. Clean the Passive 3D Kit lens periodically, or whenever you notice smudges or too much dust on thecrystal surface.
• To remove dust or smudges, gently wipe the lens with a dry and soft lens cleaning cloth.
• To remove stubborn smudges, moisten a lens cleaning cloth with lens cleaner and gently wipe the surface of thelens.
Red continuous lightThe Passive 3D Kit is connected to the projector but no synchro signal is detected.
Green continuous light 2D synchro signal detected.Green flashing light 3D synchro signal detected.
ISSUE SOLUTIONLED is not light up Ensure that the VESA > JACK cable is correctly inserted and that the
projector is not in standby mode.Red is continuously light The Passive 3D Kit is powered but cannot detect a 3D signal. Please
check that the projector is correctly set to 3D Mode (Frame Packing, Side by Side or Top and Bottom in the info menu).
Green LED flashes correctly but no 3D images are visible.
Ensure that the Passive 3D Kit is mounted in the correct direction: the Cineversum logo on the modulator must be visible. Make sure that you wear the passive 3D glasses and that your screen is 3D capable.
Avoid touching the lens surface directly to prevent finger prints or to damage the lens surface.
Avoid absolutely any water or humidity to accumulate into this device, otherwise the lifetime will be greatlyreduced. Make sure that this device is completely dry before lightning up the projector.
14 R599825 - Passive 3D Kit
Contact Information:
TEC - Cineversum7, rue LACAILLE, 75017 Paris - FRANCEWeb: www.cineversum.com
Contact informationTEC - CineVERSUM7, rue La Caille, 75017 Paris, Francewww.cineversum.com
Part. No. R599825