FREESTANDING DIMENSIONAL BUTTERFLIES · 2021. 1. 18. · • OESD Perfect Punch Tool • OESD Perfect Embroidery Press Cloth • OESD Expert Embroidery Tape TearAway • Organ Needle

It is a violation of Copyright law to make and distribute copies of electronic designs or artwork. Electronic designs are licensed to the original purchaser for use at one location. ©2021 OESD, LLC. All rights reserved.

FREESTANDING DIMENSIONAL BUTTERFLIES

#512472 DESIGNS

MATERIALS


0108 Cobblestone 2508 Hot Pink 2530 Rose 2920 Purple 3030 Amethyst 3906 Pacific Blue 3962 River Mist 4174 Charcoal 4620 Jade 4740 Aquamarine

*Instructions included after design list

2It is a violation of Copyright law to make and distribute copies of electronic designs or artwork.

Electronic designs are licensed to the original purchaser for use at one location. ©2021 OESD, LLC. All rights reserved.

Isacord Thread Colors

Note: Some designs in this collection may have been created using unique special stitches and/or techniques. To preserve design integrity when rescaling or rotating designs in your software, always rescale or rotate designs using the handles directly on-screen.

Size Inches: Size mm: Stitch Count:


DESIGNS


n 1. Front & Back Pink Fabric Placement Stitch ..2530n 2. Cut Line & Tackdown .............................................2530n 3. Light Pink Cover Stitch & Lace ..........................2530n 4. Light Blue Linework ................................................ 4740n 5. Dark Pink Cover Stitch & Linework .................2508

n 1. Front & Back Pink Fabric Placement Stitch ..2530n 2. Cut Line & Tackdown .............................................2530n 3. Light Pink Cover Stitch & Lace ..........................2530n 4. Light Blue Linework ................................................ 4740n 5. Dark Pink Cover Stitch & Linework .................2508

51247-01 Top Left Butterfly Wing FSA

51247-02 Top Right Butterfly Wing FSA

185.0 X 132.8 mm

185.0 X 132.8 mm

7.28 X 5.23 in.

7.28 X 5.23 in.

18618 St.

18730 St.

FABRIC REQUIRED

FABRIC REQUIRED

3




DESIGNS


n 1. Front & Back Teal Fabric Placement Stitch .. 4740n 2. Cut Line & Tackdown ............................................. 4740n 3. Light Aqua Cover Stitch & Lace ........................ 4740n 4. Light Pink Linework ................................................2530n 5. Dark Aqua Cover Stitch & Linework ...............4620

n 1. Front & Back Teal Fabric Placement Stitch .. 4740n 2. Cut Line & Tackdown ............................................. 4740n 3. Light Aqua Cover Stitch & Lace ........................ 4740n 4. Light Pink Linework ................................................2530n 5. Dark Aqua Cover Stitch & Linework ...............4620

51247-03 Bottom Left Butterfly Wing FSA

51247-04 Bottom Right Butterfly Wing FSA

149.5 X 100.9 mm

149.5 X 100.9 mm

5.89 X 3.97 in.

5.89 X 3.97 in.

14064 St.

14181 St.

FABRIC REQUIRED

FABRIC REQUIRED

4




DESIGNS


n 1. Front & Back Black Fabric Placement Stitch 4620n 2. Cut Line & Tackdown .............................................4620n 3. Aqua Lace ...................................................................4620n 4. Gray Cover Stitch & Detail .................................. 0108

n 1. Light Blue Lace ..........................................................3962n 2. Dark Blue Lace .........................................................3906

51247-05 Butterfly Body FSA

51247-06 Top Left Butterfly Wing FSL

161.3 X 62.6 mm

185.0 X 132.8 mm

6.35 X 2.47 in.

7.28 X 5.23 in.

5316 St.

32775 St.

FABRIC REQUIRED

5




DESIGNS


n 1. Light Blue Lace ..........................................................3962n 2. Dark Blue Lace .........................................................3906

n 1. Light Purple Lace ................................................... 3030n 2. Dark Purple Lace .....................................................2920

51247-07 Top Right Butterfly Wing FSL

51247-08 Bottom Left Butterfly Wing FSL

185.0 X 132.8 mm

149.5 X 101.1 mm

7.28 X 5.23 in.

5.89 X 3.98 in.

32775 St.

22001 St.

6




DESIGNS


n 1. Light Purple Lace ................................................... 3030n 2. Dark Purple Lace .....................................................2920

n 1. Purple Lace ............................................................... 3030n 2. Light Blue Lace ..........................................................3962n 3. Charcoal Lace .............................................................4174

51247-09 Bottom Right Butterfly Wing FSL

51247-10 Butterfly Body FSL

149.5 X 101.1 mm

161.3 X 62.6 mm

5.89 X 3.98 in.

6.35 X 2.47 in.

22001 St.

10872 St.

7

MATERIALSStabilizer

Fabric/Textiles

As per thread chart Match bobbin thread to top threadNo design requires more than one spool.

Isacord Thread Colors

• OESD AquaMesh• OESD BadgeMaster• OESD StabilStick CutAway

• 5” x 7” Pink applique fabric- 4 required• 4” x 5” Teal applique fabric- 4 required• 3” x 6.5” Black applique fabric- 2 required• Note: Fabric sizes are estimates and may result in overage.

Notions & Tools

• OESD Perfect Punch Tool• OESD Perfect Embroidery Press Cloth• OESD Expert Embroidery Tape TearAway • Organ Needle Titanium Sharp 75/11 • 20 mm mini brads; mini brads can be found at your local craft store, office supply store, or

online.



SUMMARY

Requires 1 Design

51247-01

Requires 1 Design

51247-02

Requires 1 Design

51247-03

Requires 1 Design

51247-04

Requires 1 Design

51247-05

Requires 1 Design

51247-06

Requires 1 Design

51247-07

Requires 1 Design

51247-08

Requires 1 Design

51247-09

Requires 1 Design

51247-10

Finished project size: Approximately 8” x 8”




EMBROIDERYStep 1

• The project includes freestanding applique designs and freestanding lace designs. All applique designs are stitched the same as shown in the instructions.

• All designs are stitched with matching thread in the top and bobbin. • Hoop one piece of OESD AquaMesh and one piece of OESD

BadgeMaster in the hoop for all designs.

Step 2• Prep the front and back applique fabrics with one layer of OESD StabilStick CutAway.

Step 3• Stitch Machine Step 1, Front and Back Pink Fabric Placement Stitch. • Shown here in red for instructional purposes. Follow color chart.

10


EMBROIDERYStep 4

• Remove the hoop from the machine, but NOT the project from the hoop. Lay the hoop on a flat surface.

• Cut a piece of prepared fabric slightly larger than the placement line. • Place the prepared fabric right side up, covering the placement line

completely. To secure, tape in place with OESD Expert Embroidery Tape TearAway.

Step 5• Turn the hoop over and place the back prepared applique fabric right

side up covering the placement stitch completely.• To secure, carefully tape in place with OESD Expert Embroidery Tape

TearAway. • Avoid pushing too hard on the stabilizer to prevent it from dislodging

from the hoop.

Step 6• Return the hoop to the machine.• Stitch Machine Step 2, Cut Line and Tackdown.• Shown here in black for instructional purposes. • Follow color chart, matching top and bobbin thread.

11

BACK OF HOOP

BACK OF HOOP


EMBROIDERYStep 7

• Remove the hoop from the machine, but NOT the project from the hoop.

• Trim the excess fabric as close to the stitching as possible. If the outermost stitches are cut, the inner stitches will hold the applique in place.

Step 8• Turn the hoop over and trim.

Step 9• Return the hoop to the machine and stitch the remaining colors

according to the thread chart. • Match the bobbin thread to the upper thread colors where indicated.

12

BACK OF HOOP


EMBROIDERYStep 10

• When design is complete, remove the project from the hoop and trim the stabilizer 1/4”- 1/2” outside the design.

13


ASSEMBLYStep 1

• Rinse each piece in warm running water until the design is only slightly sticky.

• Lay face down on a non-stick surface to dry. Parchment paper or a cooling rack work well. This prevents the piece from curling.

Step 2• With a dry iron press each piece, right side down, on a Perfect

Embroidery Press Cloth.

Step 3• Use the Perfect Punch tool with the 3mm attachment, punch holes in

the eyelets indicated in the photo.

14


ASSEMBLYStep 4

• Push a brad through the top eyelet of the body from the front side, then lay flat face down.

Step 5• Arrange the Top Left Wing 01 as shown face up to the right side of the body, with the eyelet on the long

end over the brad. • Note: Since the body of the butterfly is face down, the left wings are attached to the right side and the

right wings are attached to the left side. The position of the wings (left or right) refer to their position on the body from the front.

Step 6• Fold the short end of the wing over, sliding the eyelet directly over the brad.• Bend the brad points apart just enough to hold the wing in place.

15

BACK SIDE


ASSEMBLYStep 7

• Arrange the Top Right Wing 02 as shown face up to the left side of the body, with the eyelet on the long end over the brad.

Step 8• Fold the short end of the wing over, sliding the eyelet directly over the brad.• Bend the brad points flat to the wings to secure.

Step 9• Push a brad through the bottom eyelet of the body from the front side,

then lay flat face down.

16


ASSEMBLYStep 10

• Arrange the Bottom Left Wing 03 as shown face up to the right side of the body, with the eyelet on the long end over the brad.

Step 11• Fold the short end of the wing over, sliding the eyelet directly over the brad.• Bend the brad points apart just enough to hold the wing in place.

Step 12• Arrange the Bottom Right Wing 04 as shown face up on the left side of the body, with the eyelet on the

long end over the brad.

17


ASSEMBLYStep 13

• Fold the short end of the wing over, sliding the eyelet directly over the brad.• Bend the brad points flat to the wings to secure.

Step 14• The butterfly is complete. Enjoy!

Finishing Touches• TIP: Use ribbon, yarn, or as seen here, a paper clip around the brad to hang the butterfly as desired.

18

INSTRUCTIONS

19

ATTENTIONWhen printing this document, any page scaling or page fitting options in your print dialog box must be turned OFF or set to NONE so that your files will print out at their actual size. Images not printed at actual size will not function as intended.

TO SAVE PAPEROnly print the desired image by navigating to the image’s page,

go to File > Print and select “Current page” in the print dialog box. Repeat for each desired image.

APPLIQUE PATTERNS

20

Print at 100%. No scaling. This box measures 1” x 1”.

Use the box as an accuracy guide when printing

templates.

APPLIQUE PATTERNS

21



templates.

MIRRORED PATTERNS

22



templates.

MIRRORED PATTERNS

23



templates.

Documents

FREESTANDING DIMENSIONAL BUTTERFLIES · 2021. 1. 18. · • OESD Perfect Punch Tool • OESD Perfect Embroidery Press Cloth • OESD Expert Embroidery Tape TearAway • Organ Needle