Upload
others
View
5
Download
0
Embed Size (px)
Citation preview
Intake Air System and Exhaust System Component Location Index
Intake Air System and Exhaust System Component Location Index 2983 http://techinfo.honda.com/rjanisis/pubs/sm/1/2/Contents/enu/61TBAD/...
1 of 1 2/8/2019 12:33 AM
card
iagn
.com
Intake Air System and Exhaust System Component Location Index
Intake Air System and Exhaust System Component Location Index 8311 http://techinfo.honda.com/rjanisis/pubs/sm/1/2/Contents/enu/61TBAD/...
1 of 1 2/8/2019 12:33 AM
card
iagn
.com
Intake Air System and Exhaust System Component Location Index
Intake Air System and Exhaust System Component Location Index 3114 http://techinfo.honda.com/rjanisis/pubs/sm/1/2/Contents/enu/61TBAD/...
1 of 1 2/8/2019 12:34 AM
card
iagn
.com
Air Cleaner Element Removal, Installation, and Inspection
1. Air Cleaner Element - Remove
1. Open the air cleaner housing cover (A).
2. Remove the air cleaner element (B).
2. All Removed Parts - Install
1. Install the parts in the reverse order of removal.
NOTE: If the idle speed fluctuates, do the idle speedinspection.
3. Maintenance Minder - Reset (With Maintenance Minder System)
1. If the Maintenance Minder required to replace the aircleaner element, reset the Maintenance Minder with thegauge (see "Resetting the Maintenance Minder").
1. Air Cleaner Element - Inspect
1. Check the air cleaner element for damage or clogging. If itis damaged or clogged, replace it.
NOTE: Do not use compressed air to clean the air cleanerelement.
2. Clean and remove any debris from inside the air cleaner.
Air Cleaner Element Removal, Installation, and Inspection 2984 http://techinfo.honda.com/rjanisis/pubs/sm/1/2/Contents/enu/61TBAD/R...
1 of 1 12/20/2018 8:57 AM
card
iagn
.com
Air Cleaner Element Removal, Installation, and Inspection
1. Air Cleaner Element - Remove
2. All Removed Parts - Install
1. Install the parts in the reverse order of removal.
NOTE: If the idle speed fluctuates, do the idle speedinspection.
3. Maintenance Minder - Reset (With Maintenance Minder System)
1. If the Maintenance Minder required to replace the aircleaner element, reset the Maintenance Minder with thegauge (see "Resetting the Maintenance Minder").
1. Air Cleaner Element - Inspect
1. Check the air cleaner element for damage or clogging. If itis damaged or clogged, replace it.
NOTE: Do not use compressed air to clean the air cleanerelement.
2. Clean and remove any debris from inside the air cleaner.
Air Cleaner Element Removal, Installation, and Inspection 3115 http://techinfo.honda.com/rjanisis/pubs/sm/1/2/Contents/enu/61TBAD/R...
1 of 1 12/20/2018 8:56 AM
card
iagn
.com
Air Cleaner Element Removal, Installation, and Inspection
NOTE: Where icon is shown, click for further information.
1
Detailed information, notes, and precautions
*1 These parts have inspection items.
1. Air Cleaner Element - Remove
Note for installation
If the idle speed fluctuates, do the idle speed inspection.
Air Cleaner Element Removal, Installation, and Inspection 8312 http://techinfo.honda.com/rjanisis/pubs/sm/1/2/Contents/enu/61TBAD/R...
1 of 3 12/20/2018 8:56 AM
card
iagn
.com
Air Cleaner Element Removal, Installation, and Inspection 8312 http://techinfo.honda.com/rjanisis/pubs/sm/1/2/Contents/enu/61TBAD/R...
2 of 3 12/20/2018 8:56 AM
card
iagn
.com
2. All Removed Parts - Install
1. Install the parts in the reverse order of removal.
3. Maintenance Minder - Reset (With Maintenance Minder System)
1. If the Maintenance Minder required to replace the aircleaner element, reset the Maintenance Minder with thegauge (see "Resetting the Maintenance Minder").
1. Air Cleaner Element - Inspect
1. Check the air cleaner element for damage or clogging. If itis damaged or clogged, replace it.
NOTE: Do not use compressed air to clean the air cleanerelement.
2. Clean and remove any debris from inside the air cleaner.
Air Cleaner Element Removal, Installation, and Inspection 8312 http://techinfo.honda.com/rjanisis/pubs/sm/1/2/Contents/enu/61TBAD/R...
3 of 3 12/20/2018 8:56 AM
card
iagn
.com
Air Cleaner Removal and Installation
1. Air Cleaner - Remove
1. Disconnect the connector (A).
2. Remove the harness clamp (B).
3. Disconnect the intake air duct (C).
4. Remove the air cleaner (D).
2. All Removed Parts - Install
1. Install the parts in the reverse order of removal.
Air Cleaner Removal and Installation 2985 http://techinfo.honda.com/rjanisis/pubs/sm/1/2/Contents/enu/61TBAD/R...
1 of 1 12/20/2018 8:56 AM
card
iagn
.com
Air Cleaner Removal and Installation
1. Air Cleaner - Remove
1. Disconnect the intake air duct (A).
2. Disconnect the connector (B).
3. Remove the harness clamp (C).
4. Remove the air cleaner (D).
2. All Removed Parts - Install
1. Install the parts in the reverse order of removal.
Air Cleaner Removal and Installation 3116 http://techinfo.honda.com/rjanisis/pubs/sm/1/2/Contents/enu/61TBAD/R...
1 of 1 12/20/2018 8:55 AM
card
iagn
.com
Air Cleaner Removal and Installation
NOTE: Where icon is shown, click for further information.
1Air Cleaner
Torque: N·m (kgf·m, lbf·ft)
Air Cleaner Removal and Installation 8313 http://techinfo.honda.com/rjanisis/pubs/sm/1/2/Contents/enu/61TBAD/R...
1 of 6 12/20/2018 8:55 AM
card
iagn
.com
Air Cleaner Removal and Installation 8313 http://techinfo.honda.com/rjanisis/pubs/sm/1/2/Contents/enu/61TBAD/R...
2 of 6 12/20/2018 8:55 AM
card
iagn
.com
2Air Cleaner
3Air Flow Tube
Air Cleaner Removal and Installation 8313 http://techinfo.honda.com/rjanisis/pubs/sm/1/2/Contents/enu/61TBAD/R...
3 of 6 12/20/2018 8:55 AM
card
iagn
.com
Detailed information, notes, and precautions
Replace
Air Cleaner
1. Air Cleaner - Remove
2. Air Intake Seal - Remove
3. Air Intake Tube - Remove
4. All Removed Parts - Install
Air Cleaner Removal and Installation 8313 http://techinfo.honda.com/rjanisis/pubs/sm/1/2/Contents/enu/61TBAD/R...
4 of 6 12/20/2018 8:55 AM
card
iagn
.com
Air Cleaner Removal and Installation 8313 http://techinfo.honda.com/rjanisis/pubs/sm/1/2/Contents/enu/61TBAD/R...
5 of 6 12/20/2018 8:55 AM
card
iagn
.com
1. Install the parts in the reverse order of removal.
Air Flow Tube
1. Air Cleaner - Remove
2. EVAP Canister Purge Nozzle - Remove
3. Air Flow Tube B - Remove
4. Air Flow Joint - Remove
5. Air Flow Tube A - Remove
Note for installation
When installing the break head band, do the followingprocedures.
1. Tighten the break head bolt until the bolt head (A) is twistedoff completely.
NOTE: Do not use an air tool.
2. Make sure the stopper end (B) contacts to the housing end(C) after tightening the break head bolt.
6. All Removed Parts - Install
1. Install the parts in the reverse order of removal.
Air Cleaner Removal and Installation 8313 http://techinfo.honda.com/rjanisis/pubs/sm/1/2/Contents/enu/61TBAD/R...
6 of 6 12/20/2018 8:55 AM
card
iagn
.com
Intake Air Resonator Removal and Installation
NOTE: How to read the torque specifications.
1. Engine Undercover Lid - Remove (With Engine Undercover Lid)
2. Engine Undercover - Remove
3. Front Brace - Remove
4. Intake Air Resonator - Remove
5. All Removed Parts - Install
1. Install the parts in the reverse order of removal.
Intake Air Resonator Removal and Installation 6626 http://techinfo.honda.com/rjanisis/pubs/sm/1/2/Contents/enu/61TBAD/R...
1 of 1 1/16/2019 7:50 AM
card
iagn
.com
Intake Air Resonator Removal and Installation
Special Tool Required
Image Description/Tool Number
Subframe Adapter VSB02C000016*
*: Available through the Honda Tool and Equipment Program 888-424-6857.
1. Front Wheel - Remove
2. Front Bumper - Remove
3. Left Front Inner Fender - Remove
4. Steering Joint - Disconnect
NOTE: Hold the steering wheel with the steering wheel holdertool.
5. Engine Undercover Lid - Remove
6. Engine Undercover - Remove
7. Stabilizer Link - Disconnect
Intake Air Resonator Removal and Installation 3117 http://techinfo.honda.com/rjanisis/pubs/sm/1/2/Contents/enu/61TBAD/R...
1 of 9 1/16/2019 7:51 AM
card
iagn
.com
8. Tie-Rod End Ball Joint - Disconnect
9. Lower Arm Boll Joint - Disconnect
10.Connector (EPS) - Disconnect
11.Torque Rod Mounting Bolt - Remove
12.Front Brace - Remove
13.Lower Arm Mounting Bolt - Remove
Intake Air Resonator Removal and Installation 3117 http://techinfo.honda.com/rjanisis/pubs/sm/1/2/Contents/enu/61TBAD/R...
2 of 9 1/16/2019 7:51 AM
card
iagn
.com
14.Front Subframe - Support
1. Set the subframe adapter (VSB02C000016) on atransmission jack (A), line up the slots in the arms with thebolt holes on the corner of the jack base, and tighten thebolts.
2. Attach the subframe adapter to the front subframe (B).
15.Front Subframe - Remove
16.Intake Air Resonator Mounting Bolt - Remove
Intake Air Resonator Removal and Installation 3117 http://techinfo.honda.com/rjanisis/pubs/sm/1/2/Contents/enu/61TBAD/R...
3 of 9 1/16/2019 7:51 AM
card
iagn
.com
17.Intake Air Resonator - Remove
Intake Air Resonator Removal and Installation 3117 http://techinfo.honda.com/rjanisis/pubs/sm/1/2/Contents/enu/61TBAD/R...
4 of 9 1/16/2019 7:51 AM
card
iagn
.com
1. Intake Air Resonator - Install
NOTE: Make sure there are rubber seals (A) at the air cleanerbefore installing the resonator. If the rubber seals is off, it mustbe reinstalled.
2. Intake Air Resonator Mounting Bolt - Install
Intake Air Resonator Removal and Installation 3117 http://techinfo.honda.com/rjanisis/pubs/sm/1/2/Contents/enu/61TBAD/R...
5 of 9 1/16/2019 7:51 AM
card
iagn
.com
3. Front Subframe - Support
Intake Air Resonator Removal and Installation 3117 http://techinfo.honda.com/rjanisis/pubs/sm/1/2/Contents/enu/61TBAD/R...
6 of 9 1/16/2019 7:51 AM
card
iagn
.com
1. Set the subframe adapter (VSB02C000016) on atransmission jack (A), line up the slots in the arms with thebolt holes on the corner of the jack base, and tighten thebolts.
2. Attach the subframe adapter to the front subframe (B).
4. Front Subframe - Install
5. Lower Arm Mounting Bolt - Install
6. Torque Rod Mounting Bolt - Loosely Install
Intake Air Resonator Removal and Installation 3117 http://techinfo.honda.com/rjanisis/pubs/sm/1/2/Contents/enu/61TBAD/R...
7 of 9 1/16/2019 7:51 AM
card
iagn
.com
7. All Engine Mount Mounting Bolt and Nut - Tighten
8. Front Brace - Install
9. Connector (EPS) - Connect
10.Lower Arm Boll Joint - Connect
11.Tie-Rod End Ball Joint - Connect
12.Stabilizer Link - Connect
13.Engine Undercover - Install
14.Engine Undercover Lid - Install
15.Steering Joint - Connect
16.Left Front Inner Fender - Install
Intake Air Resonator Removal and Installation 3117 http://techinfo.honda.com/rjanisis/pubs/sm/1/2/Contents/enu/61TBAD/R...
8 of 9 1/16/2019 7:51 AM
card
iagn
.com
17.Front Bumper - Install
18.Front Wheel - Install
19.Wheel Alignment - Check
20.VSA Sensor Neutral Position - Memorize
Intake Air Resonator Removal and Installation 3117 http://techinfo.honda.com/rjanisis/pubs/sm/1/2/Contents/enu/61TBAD/R...
9 of 9 1/16/2019 7:51 AM
card
iagn
.com
Intake Manifold Removal and Installation
1. Intake Manifold - Exploded View
Exploded View
NOTE: Refer to the Exploded View if needed during this procedure.
1. Engine Undercover - Remove
2. Insulator - Remove
Intake Manifold Removal and Installation 2987 http://techinfo.honda.com/rjanisis/pubs/sm/1/2/Contents/enu/61TBAD/R...
1 of 4 1/16/2019 7:51 AM
card
iagn
.com
3. Throttle Body - Move
NOTE:
Do not disconnect the water bypass hoses.
Do not bend the water bypass hoses excessively.
4. Intake Manifold Bracket - Remove
5. MAP Sensor - Remove
6. External Item - Remove
1. Disconnect and remove the following intake manifold external items:
Harness clamp (A)
Bracket (B)
PCV hose (C)
EVAP canister purge valve hose (D)
Turbocharger bypass control valve solenoid hose (E)
Brake booster vacuum hose (F)
Hose clamp (G)
Intake Manifold Removal and Installation 2987 http://techinfo.honda.com/rjanisis/pubs/sm/1/2/Contents/enu/61TBAD/R...
2 of 4 1/16/2019 7:51 AM
card
iagn
.com
7. Intake Manifold - Remove
Intake Manifold Removal and Installation 2987 http://techinfo.honda.com/rjanisis/pubs/sm/1/2/Contents/enu/61TBAD/R...
3 of 4 1/16/2019 7:51 AM
card
iagn
.com
8. All Removed Parts - Install
1. Install the parts in the reverse order of removal.
NOTE:Tighten the bolts/nuts in three steps; tighten thebolts/nuts until the bolts/nuts sit on the intake manifold,tighten the bolts/nuts until the gasket is compressed,tighten the bolts/nuts to specified torque.
After installation, check that all tubes, hoses, andconnectors are installed correctly.
Intake Manifold Removal and Installation 2987 http://techinfo.honda.com/rjanisis/pubs/sm/1/2/Contents/enu/61TBAD/R...
4 of 4 1/16/2019 7:51 AM
card
iagn
.com
Intake Manifold Removal and Installation
NOTE:
Where icon is shown, click for further information.
Unless otherwise indicated, illustrations used in the procedure are for with the turbocharger bypass control solenoid valve(type A).
1
Torque: N·m (kgf·m, lbf·ft)
2
Intake Manifold Removal and Installation 8314 http://techinfo.honda.com/rjanisis/pubs/sm/1/2/Contents/enu/61TBAD/R...
1 of 5 1/16/2019 7:51 AM
card
iagn
.com
Detailed information, notes, and precautions
Torque: N·m (kgf·m, lbf·ft)
Replace
1. Engine Cover - Remove
2. 12 Volt Battery - Remove
3. 12 Volt Battery Base - Remove
4. Charge Air Cooler Pipe - Remove
Intake Manifold Removal and Installation 8314 http://techinfo.honda.com/rjanisis/pubs/sm/1/2/Contents/enu/61TBAD/R...
2 of 5 1/16/2019 7:51 AM
card
iagn
.com
Intake Manifold Removal and Installation 8314 http://techinfo.honda.com/rjanisis/pubs/sm/1/2/Contents/enu/61TBAD/R...
3 of 5 1/16/2019 7:51 AM
card
iagn
.com
NOTE: Remove the necessary part(s).
5. Vacuum Hose and Vacuum Pipe - Move
6. Fuel Hose Cover - Remove
7. Fuel Line - Disconnect
8. Bracket - Remove
9. Throttle Body - Move
NOTE:
Do not disconnect the water bypass hoses.
Do not bend the water bypass hoses excessively.
10.MAP Sensor/IAT Sensor 2 - Remove
11.Turbocharger Bypass Control Solenoid Valve - Remove (Type B)
12.Intake Manifold - Remove
Note for installation
Tighten the bolts/nuts in three steps;
-1. Tighten the bolts/nuts until the bolts/nuts sit on theintake manifold.
-2. Tighten the bolts/nuts until the gasket is compressed.
-3. Tighten the bolts/nuts to specified torque.
Turn the vehicle to the ON mode, but do not operate thestarter. After the fuel pump runs for about 2 seconds, thefuel rail will be pressurized. Repeat this two or three times.
After installation, check that all tubes, hoses, andconnectors are installed correctly.
13.All Removed Parts - Install
Intake Manifold Removal and Installation 8314 http://techinfo.honda.com/rjanisis/pubs/sm/1/2/Contents/enu/61TBAD/R...
4 of 5 1/16/2019 7:51 AM
card
iagn
.com
1. Install the parts in the reverse order of removal.
Intake Manifold Removal and Installation 8314 http://techinfo.honda.com/rjanisis/pubs/sm/1/2/Contents/enu/61TBAD/R...
5 of 5 1/16/2019 7:51 AM
card
iagn
.com
Intake Manifold Removal and Installation
1. Intake Manifold - Exploded View
Exploded View
NOTE: Refer to the Exploded View if needed during this procedure.
1. 12 Volt Battery - Remove
2. Air Cleaner - Remove
Intake Manifold Removal and Installation 3118 http://techinfo.honda.com/rjanisis/pubs/sm/1/2/Contents/enu/61TBAD/R...
1 of 5 1/16/2019 7:52 AM
card
iagn
.com
Intake Manifold Removal and Installation 3118 http://techinfo.honda.com/rjanisis/pubs/sm/1/2/Contents/enu/61TBAD/R...
2 of 5 1/16/2019 7:52 AM
card
iagn
.com
3. Intake Air Duct - Remove
4. Throttle Body - Move
NOTE:
Do not disconnect the water bypass hoses.
Do not bend the water bypass hoses excessively.
5. External Item - Remove
1. Disconnect and remove the following intake manifold external items:
PCV hose (A)
Brake booster vacuum hose (B)
Fuel feed hose (C)
EVAP canister purge hose (D)
MAP sensor connector (E)
Intake manifold bracket (F)
Intake Manifold Removal and Installation 3118 http://techinfo.honda.com/rjanisis/pubs/sm/1/2/Contents/enu/61TBAD/R...
3 of 5 1/16/2019 7:52 AM
card
iagn
.com
6. Intake Manifold Assembly - Remove
Intake Manifold Removal and Installation 3118 http://techinfo.honda.com/rjanisis/pubs/sm/1/2/Contents/enu/61TBAD/R...
4 of 5 1/16/2019 7:52 AM
card
iagn
.com
7. All Removed Parts - Install
1. Install the parts in the reverse order of removal.
NOTE:Tighten the bolts/nuts in three steps; tighten thebolts/nuts until the bolts/nuts sit on the intake manifold,tighten the bolts/nuts until the gasket is compressed,tighten the bolts/nuts to specified torque.
After installation, check that all tubes, hoses, andconnectors are installed correctly.
Intake Manifold Removal and Installation 3118 http://techinfo.honda.com/rjanisis/pubs/sm/1/2/Contents/enu/61TBAD/R...
5 of 5 1/16/2019 7:52 AM
card
iagn
.com
Throttle Body Carbon Accumulation Check
1. HDS - Connect
2. Throttle Body - Test
1. Start the engine. Hold the engine speed at 3,000 rpmwithout load (CVT in P or N, M/T in neutral) until theradiator fan comes on, then let it idle.
2. Check the REL TP SENSOR in the DATA LIST with theHDS. The reading should be below 2.46 deg. If it is not,clean the throttle body.
Throttle Body Carbon Accumulation Check 1974 http://techinfo.honda.com/rjanisis/pubs/sm/1/2/Contents/enu/61TBAD/R...
1 of 1 1/18/2019 7:52 AM
card
iagn
.com
Throttle Body Cleaning
Do not insert your fingers into the installed throttle body when you turn the vehicle to the ON mode, or while the vehicle isin ON mode. If you do, you will seriously injure your fingers if the throttle valve is activated.
1. Air Cleaner Element - Check
1. Make sure the vehicle to the OFF (LOCK) mode.
2. Remove the air cleaner element.
3. Check for damage to the air cleaner element. If the aircleaner element is damaged, replace it.
2. Throttle Body - Remove
3. Throttle Body - Clean
1. Clean off the carbon from the throttle valve and inside thethrottle body with a paper towel soaked in throttle platecleaner.
Remove the throttle body to clean it.
Be careful not to pinch your fingers.
To avoid removing the molybdenum coating, do notclean the bearing area of the throttle shaft (A).
Do not spray throttle plate cleaner directly on thethrottle body.
Use a commercially available throttle plate cleaner.
4. Throttle Body - Install
5. HDS - Connect
6. PCM - Reset
Throttle Body Cleaning 1975 http://techinfo.honda.com/rjanisis/pubs/sm/1/2/Contents/enu/61TBAD/R...
1 of 2 1/19/2019 5:40 PM
card
iagn
.com
7. TP POSITION CHECK - Select
1. Select the ETCS TEST in the INSPECTION MENU with theHDS.
2. Select TP POSITION CHECK and clear the throttle position(TP) learned value.
3. Turn the vehicle to the OFF (LOCK) mode.
4. Turn the vehicle to the ON mode, and wait 2 secondswithout pressing the accelerator pedal.
8. PCM - Idle Learn
Throttle Body Cleaning 1975 http://techinfo.honda.com/rjanisis/pubs/sm/1/2/Contents/enu/61TBAD/R...
2 of 2 1/19/2019 5:40 PM
card
iagn
.com
Throttle Body Cleaning
Do not insert your fingers into the installed throttle body when you turn the vehicle to the ON mode, or while the vehicle isin ON mode. If you do, you will seriously injure your fingers if the throttle valve is activated.
1. Air Cleaner Element - Check
1. Make sure the vehicle to the OFF (LOCK) mode.
2. Remove the air cleaner element.
3. Check for damage to the air cleaner element. If the aircleaner element is damaged, replace it.
2. Throttle Body - Remove
3. Throttle Body - Clean
1. Clean off the carbon from the throttle valve and inside thethrottle body with a paper towel soaked in throttle platecleaner.
Remove the throttle body to clean it.
Be careful not to pinch your fingers.
To avoid removing the molybdenum coating, do notclean the bearing area of the throttle shaft (A).
Do not spray throttle plate cleaner directly on thethrottle body.
Use a commercially available throttle plate cleaner.
4. Throttle Body - Install
5. HDS - Connect
6. TP POSITION CHECK - Select
Throttle Body Cleaning 9584 http://techinfo.honda.com/rjanisis/pubs/sm/1/2/Contents/enu/61TBAD/R...
1 of 2 1/19/2019 5:40 PM
card
iagn
.com
1. Select the ETCS TEST in the INSPECTION MENU with theHDS.
2. Select TP POSITION CHECK and clear the throttle position(TP) learned value.
3. Turn the vehicle to the OFF (LOCK) mode.
4. Turn the vehicle to the ON mode, and wait 2 secondswithout pressing the accelerator pedal.
Throttle Body Cleaning 9584 http://techinfo.honda.com/rjanisis/pubs/sm/1/2/Contents/enu/61TBAD/R...
2 of 2 1/19/2019 5:40 PM
card
iagn
.com
Throttle Body Removal and Installation
Do not insert your fingers into the installed throttle body when you turn the vehicle to the ON mode, or while the vehicle isin ON mode. If you do, you will seriously injure your fingers if the throttle valve is activated.
NOTE:
Where icon is shown, click for further information.
If you are replacing the throttle body, do the all procedures.
If you are removing the throttle body, do 3rd procedure (Intercooler Pipe Bracket - Remove) through 13th procedure(Engine Coolant - Refill).
1
Detailed information, notes and precautions
Throttle Body Removal and Installation 9164 http://techinfo.honda.com/rjanisis/pubs/sm/1/2/Contents/enu/61TBAD/R...
1 of 4 1/19/2019 5:41 PM
card
iagn
.com
Torque: N·m (kgf·m, lbf·ft)
Throttle Body Removal and Installation 9164 http://techinfo.honda.com/rjanisis/pubs/sm/1/2/Contents/enu/61TBAD/R...
2 of 4 1/19/2019 5:41 PM
card
iagn
.com
Replace
1. HDS - Connect
2. TP POSITION CHECK - Select
1. Select the INSPECTION MENU on the HDS.
2. Do the TP POSITION CHECK in the ETCS TEST.
3. Turn the vehicle to the OFF (LOCK) mode.
4. Turn the vehicle to the ON mode, and wait 2 secondswithout pressing the accelerator pedal.
3. Intercooler Pipe Bracket - Remove
4. 12 Volt Battery Base - Remove
5. Throttle Body Inlet Pipe and Throttle Body Connector Tube - Remove
6. Connector (Throttle Body) - Disconnect
7. Harness Bracket - Remove
8. Water Bypass Hose - Disconnect and Plug
9. Throttle Body and Throttle Flange Plate - Remove
NOTE: Be careful not to drop the throttle flange plates toprevent other parts from damage.
Note for installation
When tighten the throttle body mounting bolts in a crosspattern in three steps;
Throttle Body Removal and Installation 9164 http://techinfo.honda.com/rjanisis/pubs/sm/1/2/Contents/enu/61TBAD/R...
3 of 4 1/19/2019 5:41 PM
card
iagn
.com
-1. Tighten the bolts until they sit on the throttle body.
-2. Tighten the bolts until the gasket is compressed andboth parts are contacted.
-3. Tighten the bolts to specified torque.
10.Throttle Body Cover - Remove (If Necessary)
Note for installation
Tighten the mounting screws to the specified torque in thenumbered sequence shown.
11.Throttle Body Lower Case - Remove (If Necessary)
12.All Removed Parts - Install
1. Install the parts in the reverse order of removal.
13.Engine Coolant - Refill
Throttle Body Removal and Installation 9164 http://techinfo.honda.com/rjanisis/pubs/sm/1/2/Contents/enu/61TBAD/R...
4 of 4 1/19/2019 5:41 PM
card
iagn
.com
Throttle Body Removal and Installation
Do not insert your fingers into the installed throttle body when you turn the vehicle to the ON mode, or while the vehicle isin ON mode. If you do, you will seriously injure your fingers if the throttle valve is activated.
NOTE:
Where icon is shown, click for further information.
If you are replacing the throttle body, do the all procedures.
If you are removing the throttle body, do 3rd procedure (Intake Air Duct F - Remove) through 9th procedure (EngineCoolant - Refill).
1
Throttle Body Removal and Installation 1976 http://techinfo.honda.com/rjanisis/pubs/sm/1/2/Contents/enu/61TBAD/R...
1 of 4 1/19/2019 5:41 PM
card
iagn
.com
Throttle Body Removal and Installation 1976 http://techinfo.honda.com/rjanisis/pubs/sm/1/2/Contents/enu/61TBAD/R...
2 of 4 1/19/2019 5:41 PM
card
iagn
.com
Detailed information, notes and precautions
Torque: N·m (kgf·m, lbf·ft)
Replace
1. HDS - Connect
2. TP POSITION CHECK - Select
1. Select the INSPECTION MENU on the HDS.
2. Do the TP POSITION CHECK in the ETCS TEST.
3. Turn the vehicle to the OFF (LOCK) mode.
4. Turn the vehicle to the ON mode, and wait 2 secondswithout pressing the accelerator pedal.
3. Intake Air Duct F - Remove
4. Connector (Throttle Body) - Disconnect
5. Water Bypass Hose - Disconnect and Plug
6. Throttle Body - Remove
Note for installation
Tighten the throttle body mounting bolts in a cross patternin three steps;
-1. Tighten the bolts until they sit on the throttle body.
-2. Tighten the bolts until the gasket is compressed andboth parts are contacted.
-3. Tighten the bolts to specified torque.
7. Throttle Body Lower Case - Remove (If needed)
8. All Removed Parts - Install
Throttle Body Removal and Installation 1976 http://techinfo.honda.com/rjanisis/pubs/sm/1/2/Contents/enu/61TBAD/R...
3 of 4 1/19/2019 5:41 PM
card
iagn
.com
1. Install the parts in the reverse order of removal with a newgasket and a new O-ring.
9. Engine Coolant - Refill
10.PCM - Reset
11.PCM - Idle Learn
Throttle Body Removal and Installation 1976 http://techinfo.honda.com/rjanisis/pubs/sm/1/2/Contents/enu/61TBAD/R...
4 of 4 1/19/2019 5:41 PM
card
iagn
.com
Throttle Body Removal and Installation
Do not insert your fingers into the installed throttle body when you turn the vehicle to the ON mode, or while the vehicle isin ON mode. If you do, you will seriously injure your fingers if the throttle valve is activated.
NOTE:
Where icon is shown, click for further information.
If you are replacing the throttle body, do the all procedures.
If you are removing the throttle body, do 3rd procedure (Intake Air Duct - Remove) through 9th procedure (Engine Coolant -Refill).
1
Throttle Body Removal and Installation 2023 http://techinfo.honda.com/rjanisis/pubs/sm/1/2/Contents/enu/61TBAD/R...
1 of 6 1/19/2019 5:41 PM
card
iagn
.com
Detailed information, notes and precautions
Torque: N·m (kgf·m, lbf·ft)
Replace
1. HDS - Connect
Throttle Body Removal and Installation 2023 http://techinfo.honda.com/rjanisis/pubs/sm/1/2/Contents/enu/61TBAD/R...
2 of 6 1/19/2019 5:41 PM
card
iagn
.com
2. TP POSITION CHECK - Select
Throttle Body Removal and Installation 2023 http://techinfo.honda.com/rjanisis/pubs/sm/1/2/Contents/enu/61TBAD/R...
3 of 6 1/19/2019 5:41 PM
card
iagn
.com
1. Select the INSPECTION MENU on the HDS.
2. Do the TP POSITION CHECK in the ETCS TEST.
3. Turn the vehicle to the OFF (LOCK) mode.
4. Turn the vehicle to the ON mode, and wait 2 secondswithout pressing the accelerator pedal.
3. Intake Air Duct - Remove
Note for installation
After tightening the hose band screw (A), make sure theclearance (B) is 9.0-10.0 mm (0.354-0.394 in).
4. Connector (Throttle Body) - Disconnect
5. Bracket - Remove
6. Water Bypass Hose - Disconnect and Plug
7. Throttle Body and Throttle Flange Plates - Remove
Note for removal
Be careful not to drop the throttle flange plates to preventother parts from damage.
Note for installation
When tighten the throttle body mounting bolts in a crosspattern in three steps;
-1. Tighten the bolts until they sit on the throttle body.
-2. Tighten the bolts until the gasket is compressed andboth parts are contacted.
-3. Tighten the bolts to specified torque.
Throttle Body Removal and Installation 2023 http://techinfo.honda.com/rjanisis/pubs/sm/1/2/Contents/enu/61TBAD/R...
4 of 6 1/19/2019 5:41 PM
card
iagn
.com
Throttle Body Removal and Installation 2023 http://techinfo.honda.com/rjanisis/pubs/sm/1/2/Contents/enu/61TBAD/R...
5 of 6 1/19/2019 5:41 PM
card
iagn
.com
8. All Removed Parts - Install
1. Install the parts in the reverse order of removal with a newgasket.
9. Engine Coolant - Refill
10.PCM - Reset
11.PCM - Idle Learn
Throttle Body Removal and Installation 2023 http://techinfo.honda.com/rjanisis/pubs/sm/1/2/Contents/enu/61TBAD/R...
6 of 6 1/19/2019 5:41 PM
card
iagn
.com