Foreword...*2: For details about the combination meter, refer to the Owner’s Manual for your vehicle. B2522BE-A.book 3 ページ 2015年5月15日金曜日午後12時22分

ForewordCongratulations on choosing a SUBARU vehicle equipped with EyeSightTM.EyeSight incorporates the latest driver assistance features available fromSUBARU, including such features as Adaptive Cruise Control, a Lead Vehicle StartAlert and a Lane Departure and Lane Sway Warning, all of which are designed toassist the driver in making decisions and increase driver comfort andconvenience. Initially, the operation and use of the various EyeSight features maybe unfamiliar to you. That is why we urge you to read this manual carefully beforeusing EyeSight. We also recommend that you first take the time to test EyeSight inorder to experience its features for yourself so that you can become familiar withtheir operation.

Please keep in mind that it is the responsibility of drivers to operate their vehiclessafely at all times. Drivers should always remain alert and should never becomecomplacent while operating their vehicles because of the presence of EyeSight. EyeSight is never a substitute for active driver involvement and it may not operateoptimally under all driving conditions.

This booklet is a supplement to the Owner’s Manual for your SUBARU vehicle andcontains a detailed description of EyeSight. It should be read in conjunction withyour Owner’s Manual so that you will gain a thorough understanding of the properoperation of your vehicle.

The information, specifications and illustrations found in this booklet are those ineffect at the time of printing. FUJI HEAVY INDUSTRIES LTD. reserves the right tochange specifications and designs at any time without prior notice and withoutincurring any obligation to make the same or similar changes on vehiclespreviously sold.

Please keep this booklet together with your Owner’s Manual and leave it in thevehicle at the time of resale. The next owner will need the information it contains.

FUJI HEAVY INDUSTRIES LTD., TOKYO, JAPAN is a registered trademark of FUJI HEAVY INDUSTRIES LTD.

© Copyright 2015 FUJI HEAVY INDUSTRIES LTD.

B2522BE-A.book 1 ページ２０１５年５月１５日　金曜日　午後１２時２２分

3

1

2

4

5

6

7

8

EyeSight

About EyeSight .................................................................. 2Pre-Collision Braking System........................................... 20Adaptive Cruise Control ................................................... 32Lane Keep Assist ............................................................. 54Pre-Collision Throttle Management.................................. 62Lane Departure Warning.................................................. 68Lane Sway Warning ......................................................... 71Lead Vehicle Start Alert ................................................... 74Conventional Cruise Control ............................................ 75List of buzzer sounds ....................................................... 85EyeSight malfunction and temporary stop ....................... 86Customizing functions ...................................................... 89Message screen list ......................................................... 91Troubleshooting ............................................................... 93


2

About EyeSight

EyeSight is a driving support system that uses a range of functions to assist the driver inmaking decisions in order to provide for more safe and comfortable driving and to reducedriver fatigue. Making use of images created by stereo cameras specially designed bySUBARU, EyeSight detects the vehicle in front, obstacles, traffic lanes and other items.

EyeSight

WARNING

Drivers are responsible for driving safely. Always comply with alltraffic rules and regulations regardless of the fact that your vehicleis equipped with EyeSight. Always maintain a safe following dis-tance behind the vehicle in front of you, pay attention to your sur-roundings and the driving conditions, operate the brake pedal andtake other action as necessary in order to maintain a safe followingdistance.Never attempt to drive relying on EyeSight alone.EyeSight is intended to assist the driver in making decisions inorder to reduce the chance of accidents or damage and lessen theburden on the driver.When a warning is activated, pay attention to what is in front of youand to your surroundings, operate the brake pedal and take otheraction as necessary.This system is not designed to support driving in poor visibility orin extreme weather conditions, or to protect against careless driv-ing when the driver is not paying complete attention to the roadahead. It also cannot prevent collisions from occurring in all drivingconditions.There are limits to the EyeSight recognition performance and con-trol performance. Be sure to read the instructions for each functionbefore using the system, and always use it properly. Improper usemay lead to failure of control performance, which could cause anaccident.Refer to the following pages for each function:• For the Pre-Collision Braking System, refer to page 20.• For Adaptive Cruise Control, refer to page 32.• For Pre-Collision Throttle Management, refer to page 62.• For Conventional Cruise Control, refer to page 75.


About EyeSight

3

The EyeSight system in your vehicle is designed for use in coun-tries in which traffic operates on the right-hand side of the road.EyeSight for LHD vehicles such as yours is not designed for use incountries in which vehicles are driven on the left-hand side of theroad.• The system may not operate correctly under the conditions listed below.

When these conditions occur, turn off the Pre-Collision Braking System.Also, do not use Adaptive Cruise Control and Conventional Cruise Control.

- The tire pressure is not correct.*1- The temporary spare tire is installed on any wheel.*1- Tires that are worn or have large variations in wear conditions are

installed.*1- Tires other than those of the designated size are installed.*1- Flat tires have been fixed temporarily with a tire repair kit.- The suspension has been modified (including a genuine SUBARU sus-

pension that has been modified).- Any object that disturbs the stereo cameras’ view is installed on the vehi-

cle.- The headlights are dirty or they have snow and ice or dirt on them.

(Objects are not correctly illuminated and are difficult to detect.)- The optical axes are not aligned correctly. (Objects are not correctly illu-

minated and are difficult to detect.)- The lights including headlights and fog lamps have been modified.- Vehicle operation has become compromised due to an accident or mal-

function.- The brake system warning light is illuminated in red.- A heavy cargo is loaded onto or inside the vehicle.- The maximum number of occupants is exceeded.- There is something wrong with the combination meter; such as when the

lights do not illuminate, the beeps do not sound, the display is differentfrom when it is normal, etc.*2*1: The wheels and tires have functions that are critically important. Be

sure to use the correct ones. For details, refer to the Owner’s Manualfor your vehicle.

*2: For details about the combination meter, refer to the Owner’s Manualfor your vehicle.


About EyeSight

4

CAUTION• The characteristics of the stereo cameras are similar to those of human

eyes. For this reason, conditions that make it difficult for the driver to seein the forward direction have the same effect on the stereo cameras andmake it difficult for the system to detect vehicles, obstacles and trafficlanes.

• Detection by the EyeSight system is limited to objects that are within therange of the stereo cameras’ field of vision. Also, after an object enters therange of the cameras’ field of vision, it may take some time for the systemto detect it as a controllable target and warn the driver.

• Under the conditions listed below, it will become more difficult for the sys-tem to detect the vehicle in front, motorcycles, bicycles, pedestrians andobstacles on the road, and lane markers. Also, EyeSight may temporarilystop operating. However, the temporary stop will be canceled once theseconditions have improved and the vehicle is driven for a short period oftime.

- Bad weather (for example heavy rain, a blizzard or thick fog). In particu-lar, the system is more likely to temporarily stop operating when there isan oil film adhering to the windshield, a glass coating has been appliedor old wipers are used.)

- When affected by strong light from the front (sunlight or headlight beamsof oncoming traffic, etc.)

- When the front windshield washer is being used.- The windshield has become fogged, or snow, dirt, dust or frost has

adhered to it, reducing the stereo cameras’ field of view.- The vehicle is tilted at an extreme angle due to loaded cargo or other

factors.- When visibility is poor due to sand, smoke or water vapor in the air, or

when the vehicle in front or oncoming traffic causes water, snow, dirt orother substances to obscure the view

- When the stereo cameras’ field of view is obstructed (for example by acanoe on the roof of the vehicle)

S01970

Low objects surrounding the vehicle cannot be detected.


About EyeSight

5

- When passing through the entrance or exit of a tunnel- When the rear aspect of the vehicle in front is low, small or irregular (for

example a low bed trailer, etc.)- When there is a fence, a wall or a shutter, etc. with a uniform pattern (a

striped pattern, brick, etc.) or with no pattern in front- When there is a wall or door made of glass or a mirror in front- When driving at night or in a tunnel when there is a vehicle in front that

does not have its taillights on- When passing a banner or flag, low branches on a tree or thick/tall vege-

tation- On steep uphill or downhill grades- When the stereo cameras are obstructed by a hand, etc. (If even one of

the cameras is obstructed, the system does not operate properly.)- When it is completely dark and no objects are detected- When the area around the vehicle has a uniform color (such as when

completely covered in snow, etc.)- When the stereo camera lenses are dirty due to fingerprints, etc. - When accurate detection is not possible due to reflections in the front

windshield- When the stereo cameras have become misaligned due to a strong

impact• Under the conditions listed below, EyeSight may temporarily stop operat-

ing. If this occurs, EyeSight will resume operating when the conditionsimprove.

- The temperature inside the vehicle is high, such as after the vehicle wasleft in bright sunshine, or the temperature inside the vehicle is low, suchas after the vehicle was left in an extremely cold environment.

- Immediately after the engine starts• When there is a malfunction in the EyeSight system, turn off the Pre-Colli-

sion Braking System (⇒ refer to page 30) and the Lane Departure Warning(⇒ refer to page 70), and stop using the Adaptive Cruise Control and Con-ventional Cruise Control. Contact a SUBARU dealer and have the systeminspected.

• When the Vehicle Dynamics Control warning light is illuminated, the Pre-Collision Braking System may not operate properly. In this case, turn offthe Pre-Collision Braking System. Also, do not use the Adaptive CruiseControl or Conventional Cruise Control.


About EyeSight

6

NOTE• EyeSight records and stores the following data when the Pre-Collision

Braking System is operated. It does not record conversations or otheraudio data.

- Stereo camera image data- Distance from the vehicle in front- Vehicle speed- Steering wheel turning angle- Lateral movement with regard to the direction of travel- Accelerator pedal operation status- Brake pedal operation status- Select lever position- Odometer reading- Data related to ABS, Vehicle Dynamics Control and Traction Control

FunctionSUBARU and third parties contracted by SUBARU may acquire and usethe recorded data for the purpose of vehicle research and development.SUBARU and third parties contracted by SUBARU will not disclose orprovide the acquired data to any other third party except under the fol-lowing conditions.• The vehicle owner has given his/her consent.• The disclosure/provision is based on a court order or other legally

enforceable request.• Data that has been modified so that the user and vehicle cannot be

identified is provided to a research institution for statistical processingor similar purposes.


About EyeSight

7

The stereo cameras are installed at the posi-tions of the front map lights.

Continued on next page ⇒

Handling of the Stereo Cameras

CAUTION• A function is included that will automatically detect that the fronts of the

stereo cameras are dirty. However it is not 100% effective.Under certain conditions, this function may fail to detect that the fronts ofthe stereo cameras have become dirty. In addition, this function may notdetect that there is snow or ice on the windshield close to the stereo cam-eras. In such conditions, be sure to keep the windshield clean at all times(indicated by ). Otherwise the system may not operate correctly.When this function detects that the fronts of the stereo cameras are dirty,no EyeSight functions are activated except for Conventional CruiseControl.

• The stereo camera is a precision component. Always observe the followingprecautions especially when handling lenses.

- Never touch the stereo camera lenses, and do not attempt to wipe orclean the lenses. Doing so could cause lens damage or contaminationand lead to improper system performance.If you ever touch a lens for any reason, be sure to contact a SUBARUdealer.

A

S01107

Stereo cameras


About EyeSight

8

⇒ Continued from previous page

- When cleaning the frontwindshield, cover the frontof the camera casing withpaper that does not collectdust, such as copy paper.Affix the paper to preventglass cleaner from gettingon the camera lenses. Atthis point, make sure thatthe tape’s adhesive sur-face does not come incontact with the windshieldor the lens. Be sure toremove the paper after cleaning.

- When having the inside of windshield cleaned at a service station, etc.,be sure to request that the attendant covers the camera covers beforewashing the vehicle.

- Do not subject the stereo cameras to a strong impact.- Do not remove or disassemble the stereo cameras.- Do not change the positions where the stereo cameras are installed or

modify any of the surrounding structures.• Do not install an interior rearview mirror other than a genuine SUBARU

rearview mirror (such as a wide-type mirror) and the sun visor. Also, usethe rearview mirror so that it does not obstruct the stereo cameras. Failureto do so may affect the stereo cameras’ field of vision and could preventthe EyeSight system from functioning properly.

S01097

S00509


About EyeSight

9


• Do not install any accessories other than the ones designated by SUBARUon the prohibited areas shown in the illustrations (grey zones). Even if some accessories are installed on the outside of the prohibited areas,abnormal operation of EyeSight may occur due to the reflection of the light orany objects. In this situation, move the accessories. For details, contact aSUBARU dealer.

<Side view> <Front view>

• Do not place any objects on top of the instrument panel. The stereo camerasmay not be able to detect objects accurately and the EyeSight system maynot function properly due to reflections in the front windshield. For details,contact a SUBARU dealer.

• If the top of the instrument panel is polished with chemicals or other sub-stances, the stereo cameras may not be able to detect objects accuratelyand the EyeSight system may not operate properly due to reflections in thefront windshield.

• Do not install any wiper blades other than genuine SUBARU wiper blades.Doing so may affect the stereo cameras’ field of vision and could prevent theEyeSight system from functioning properly.

• Replace damaged wiper blades as soon as possible. The stereo camerasmay not be able to detect objects accurately and the EyeSight system maynot function properly due to liquid remaining on the windshield.

• Do not install any accessorieson the front side such as onthe hood or the grille. It mayaffect the camera view andthe system may not operatecorrectly.

• Make sure that the cargoloaded on the roof does notobstruct or interfere in the ste-reo cameras’ field of view.Obstructing the stereo cam-eras’ view may impair the sys-tem operation. For details,contact a SUBARU dealer.

S02068Monitor or other accessories

S01098


About EyeSight

10


• Keep the windshield (outside and inside) clean at all times. When the wind-shield has become fogged, or it has a dirt or an oil film on it, the stereocamera may not detect objects accurately and the EyeSight system maynot operate correctly. Never mount any device to the center air vent, asany airflow change may impact EyeSight performance.

• Do not place any stickers or accessories on the windshield (outside orinside). If you have to do so (for example, legally required or electronic tolltag), avoid the area directly in front of the camera. Doing so may adverselyaffect the field of vision of the stereo camera and can cause improperoperation of the system. For details, contact a SUBARU dealer.

• Do not use any glass coating agents or similar substances on the wind-shield. Doing so may prevent the system from operating correctly.

• Do not install a film on the front windshield. The system may not operatecorrectly.

• If there are scratches or cracks on the front windshield, contact a SUBARUdealer.

• To have the front windshield replaced or repaired, contact a SUBARUdealer. Do not install a front windshield other than a genuine SUBARUfront windshield. The stereo cameras may not be able to detect objectsaccurately and the EyeSight system may not operate properly.


About EyeSight

11

EyeSight includes the following functions.

■ Pre-Collision Braking SystemThis function uses a following distance warning feature to warn the driver to take evasiveaction when there is the possibility of a collision with a vehicle or obstacle in front of thedriver’s vehicle. If the driver still does not take evasive action, the brakes are quickly appliedautomatically just before the collision in order to reduce the collision damage or, if possible,prevent the collision.⇒ Refer to page 20.

■ Adaptive Cruise ControlThis function maintains the set vehicle speed and when there is a vehicle in front in thesame traffic lane, it tracks the speed of the vehicle in front up to the maximum of the setvehicle speed.⇒ Refer to page 32.

■ Lane Keep AssistThis function supports control of drifting out of a lane by detecting lane markings (e.g., whitelines) on highways, etc. and assisting steering operation.⇒ Refer to page 54.

■ Pre-Collision Throttle ManagementThis function reduces accidental forward movement caused by the selector lever beingplaced in the wrong position or the accelerator pedal being accidently depressed, ordepressed too strongly.⇒ Refer to page 62.

■ Lane Departure WarningThis function warns the driver when the vehicle is about to depart the traffic lane during driv-ing.⇒ Refer to page 68.

■ Lane Sway WarningThis system detects vehicle drifting caused by driver fatigue, failure to concentrate on theroad, inattention, strong crosswinds or other factors, and warns the driver.⇒ Refer to page 71.

EyeSight Functions


About EyeSight

12

■ Lead Vehicle Start AlertThis function notifies the driver when the vehicle in front has started moving but the driver’svehicle has not.⇒ Refer to page 74.

■ Conventional Cruise ControlIn this mode, the system maintains a constant vehicle speed. Tracking of the vehicle in frontdoes not occur. This function can be used even when the stereo cameras have temporarilystopped operating. (⇒ Refer to page 87.) (This function is used by switching from AdaptiveCruise Control to Conventional Cruise Control.)⇒ Refer to page 75.

NOTEEyeSight does not operate when the engine is not running.


About EyeSight

13

Instrument panel display layout

(1) EyeSight display area (13) Lead vehicle indicator(2) Adaptive Cruise Control indicator (14) The pop-up screen area(3) Conventional Cruise Control indicator (15) EyeSight temporary stop indicator (White)(4) READY indicator (16) EyeSight warning indicator (Yellow)(5) OFF indicator (17) Electric parking brake indicator light(6) SET indicator (18) Lane Departure Warning OFF indicator light(7) HOLD indicator (19) Pre-Collision Braking System OFF indicator light(8) Lane indicator (20) Vehicle Dynamics Control OFF indicator light(9) Set vehicle speed display (21) Selector indicator/shift position indicator(10) Your vehicle indicator (22) X-mode indicator(11) Lane keep Assist indicator (23) Brake system warning light(12) Following distance setting indicator

S02042

(21) (22) (23)(18) (19) (20)(17)

(14)

(12)

(11)

(13)

(1)

(2)

(3)

(4)(5)(6)(7)

(10)

(9)(8)

(15) (16)

* Display units can be changed in Screen Settings. For details, refer to the Owner’s Manual for your vehicle.

本文.fm 13 ページ２０１５年５月２１日　木曜日　午前８時４２分

About EyeSight

14

■ CRUISE indicator• This indicator illuminates when the main cruise control is on.

: Adaptive Cruise Control (Adaptive Cruise Control indicator) : Conventional Cruise Control (Conventional Cruise Control indicator)

⇒ Refer to pages 38 and 75.• When Adaptive Cruise Control is set and the vehicle detects a car in front, this indicator

(white) turns green.⇒ Refer to page 40.

■ SET indicator illuminates when cruise control* is set.

⇒ Refer to pages 39 and 78.* Adaptive Cruise Control and Conventional Cruise Control

■ READY indicator illuminates when cruise control* can be set.


■ HOLD indicator illuminates when the stay-stopped function is operated while Adaptive Cruise Control is

on.⇒ Refer to page 46.

■ OFF indicator illuminates when cruise control* has been automatically canceled.


■ Lead vehicle indicator• When Adaptive Cruise Control is set or when the vehicle is stopped, this indicator illumi-

nates when a vehicle in front has been detected.⇒ Refer to page 40.• This indicator illuminates in the following cases.

- The Lead Vehicle Start Alert is active.- The Pre-Collision Braking System is active.- The “brake more” warning is active.- Pre-Collision Throttle Management is active.


About EyeSight

15

■ Following distance setting indicatorIndicates the following distance setting that was set with the / (Following distancesetting) switch.⇒ Refer to page 45.

■ Set vehicle speed displayDisplays the set vehicle speed.⇒ Refer to pages 38 and 76.

■ Your vehicle indicatorWhen the brake pedal is depressed or the brake control function is active, the brake light onthe indicator illuminates in red.

■ Lane keep Assist indicator• This indicator illuminates when Lane Keep Assist is turned on by pressing the (Lane

Keep Assist) switch.• While the Lane Keep Assist system is activated, if the vehicle travels across a lane

marker the indicator turns from white to green.⇒ Refer to pages 54 and 58.

■ Selector indicator/shift position indicatorThis indicator illuminates and shows which position the selector lever or the gear is in.

■ Lane indicator• When Lane Keep Assist is in the standby status or is operating, the lane indicator of the

detected lane will illuminate (left, right or both left and right).• Either the left or right indicator blinks depending on which side your vehicle is drifting

towards when Lane Departure Warning operates.• The left and right indicators alternately blink when Lane Sway Warning operates.⇒ Refer to pages 68 and 71.

■ EyeSight warning indicator (yellow)• This indicator illuminates or flashes when a malfunction occurs in the EyeSight system.• When it is illuminated or flashing, none of the EyeSight functions can be used (including

Adaptive Cruise Control and the Pre-Collision Braking System, etc.).⇒ Refer to page 86.


About EyeSight

16

■ EyeSight temporary stop indicator (white)• This indicator illuminates when the EyeSight system is temporarily stopped.• When the ignition switch is placed in the ON position, it will illuminate if the

(CRUISE) switch is set to ON within approximately 7 seconds of the engine starting. Itturns off when approximately 7 seconds have elapsed since the engine started.

• When it is illuminated, none of the EyeSight functions can be used except for Conven-tional Cruise Control.

⇒ Refer to page 87.

■ Lane Departure Warning OFF indicator light• This indicator illuminates when the Lane Departure Warning and Lane Sway Warning are

off.• It also illuminates when the ignition switch is turned to the ON position, and then approxi-

mately 7 seconds after the engine starts, the Lane Departure Warning will be turned off orremain illuminated depending on the current status (ON or OFF).


■ Pre-Collision Braking System OFF indicator light• Illuminates when the Pre-Collision Braking System and Pre-Collision Throttle

Management are off.• It also illuminates when the ignition switch is turned to the ON position, and then turns off

approximately 7 seconds after the engine starts.⇒ Refer to page 31.

■ Vehicle Dynamics Control OFF indicator light• It illuminates when the engine starts and turns off within approximately 2 seconds.• It illuminates when the Vehicle Dynamics Control OFF switch is pressed and Vehicle

Dynamics Control is off. Refer to the Owner’s Manual for your vehicle.

■ Brake system warning light (red)If the brake system warning light should illuminate while driving with the parking brake fullyreleased, turn off the Pre-Collision Braking System. Also, do not use Adaptive Cruise Con-trol or Conventional Cruise Control.

■ Electronic parking brake indicator lightThis indicator light illuminates when the electronic parking brake is applied.⇒ Refer to the Owner’s Manual for details.


About EyeSight

17

Switch layout

(1) (Lane Keep Assist) switch (6) switch

(2) / (Following distance setting) switch (7) (Info)/SET switch

(3) RES/+ switch (8) switch

(4) SET/- switch (9) (Lane Departure Warning OFF) switch

(5) (CRUISE) switch (10) (Pre-Collision Braking System OFF) switch

S01984

(9)

(8)

(6)

(2)

(3) (4)

(1)

(7)

(10)

(5)


About EyeSight

18

■ (CRUISE) switch• Switches cruise control* on/off.• When this switch is pressed “ ” or “ ” appears on the EyeSight display area in the

multi information display. This indicates that the main cruise control is turned on.⇒ Refer to pages 38 and 76.• Can be used to cancel the cruise control.⇒ Refer to pages 48 and 81.* Adaptive Cruise Control and Conventional Cruise Control

■ RES/SET switch●SET/-

• Can be used to set cruise control*.• Can be used to reduce the set vehicle speed (when cruise control* is currently set).⇒ Refer to pages 39 and 43 (for Adaptive Cruise Control).⇒ Refer to pages 78 and 80 (for Conventional Cruise Control).

●RES/+ • After cruise control* is canceled, this switch can be used to resume the cruise control

function at the vehicle speed that was previously set.• Can be used to increase set vehicle speed (when cruise control* is currently set).⇒ Refer to pages 42 and 51 (for Adaptive Cruise Control).⇒ Refer to pages 79 and 84 (for Conventional Cruise Control).* Adaptive Cruise Control and Conventional Cruise Control

■ / (Following distance setting) switch• Can be used to switch the set following distance in 4 stages: (only when Adaptive Cruise

Control is on).⇒ Refer to page 45.• When the (CRUISE) switch is on, press and hold this switch for approximately 2

seconds or longer to select Adaptive Cruise Control or Conventional Cruise Control.

■ (Lane Keep Assist) switchSwitches Lane Keep Assist on/off.⇒ Refer to page 43.


About EyeSight

19

■ switch/ switchThese are used in the following situations.• When switching the screen displayed on the multi information display.• When changing the Warning Volume settings, etc.⇒ Refer to page 89.

■ (Info)/SET switchThis is used in the following situations.• When displaying the message that appeared in the pop-up screen area again.⇒ Refer to page 91.• When changing the Warning Volume settings, etc.⇒ Refer to page 89.

■ (Pre-Collision Braking System OFF) switchPress and hold this switch for approximately 2 seconds or longer to turn off the Pre-CollisionBraking System and Pre-Collision Throttle Management.When these functions are off, the Pre-Collision Braking System OFF indicator light on theinstrument panel illuminates.Press and hold the switch again to turn on the Pre-Collision Braking System and Pre-Collision Throttle Management. This turns off the Pre-Collision Braking System OFF indica-tor light.⇒ Refer to page 30.

■ (Lane Departure Warning OFF) switchPress and hold this switch for approximately 2 seconds or longer to turn off the LaneDeparture Warning and Lane Sway Warning functions.When these functions are off, the Lane Departure Warning OFF indicator light on the instru-ment panel illuminates.Press and hold the switch again to turn on the Lane Departure Warning and Lane SwayWarning functions. This turns off the Lane Departure Warning OFF indicator light.⇒ Refer to page 70.


20

Pre-Collision Braking SystemWhen there is the risk of a rear-end collision with a obstacle in front, the EyeSight systemhelps to minimize or prevent a collision by warning the driver. If the driver still does not takeevasive action to avoid a collision, the brakes can be automatically applied just before thecollision in order to reduce impact damage, or if possible, prevent the collision. If the drivertakes evasive action to avoid a collision, Pre-Collision Brake Assist will operate in order tohelp the driver to prevent the collision.This system can be effective not only with direct rear-end collisions, but also with offsetrear-end collisions. This function can be activated when the select lever is in the , or

positions.

WARNING

• Never use the Pre-Collision Braking System and Pre-Collision Brake Assist tostop your car or avoid a collision under ordinary conditions. These functionscannot prevent collisions under all conditions. If the driver relies only on thePre-Collision Braking System for Brake operation, collisions may occur.

• When a warning is activated, pay attention to the front of the vehicle and itssurroundings, and operate the brake pedal and/or take other actions if nec-essary.

• The EyeSight Pre-Collision Braking System is primarily designed to pre-vent rear-end collisions with other vehicles when possible and to minimizedamage and injuries in the event of a collision. In addition to other vehi-cles, things such as motorbikes, bicycles and pedestrians can also betreated as obstacles. However, there may be cases when detection is notpossible depending on a variety of conditions*2. For example, when a vehi-cle is viewed from the side, oncoming vehicle, vehicles approaching inreverse, small animals or children, or walls or doors are not likely to bedetected.

• The Pre-Collision Braking System will operate at the point when it deter-mines that a collision cannot be avoided and is designed to apply strongbraking force just before a collision. The result of this varies depending ona variety of conditions*2. Because of this, performance of this function willnot always be the same.

• When the Pre-Collision Braking System is activated, it will continue tooperate even if the accelerator pedal is partially depressed. However, it willbe canceled if the accelerator pedal is deeply depressed.

• If the driver depresses the brake pedal or turns the steering wheel, the systemmay determine that this constitutes evasive action by the driver, and the auto-matic braking control may not activate in order to allow the driver full control.

• When the difference in speed with the obstacle in front is the following fig-ure*1 or more, it may not be possible to avoid a collision. Even if the speeddifference is the following figure*1 or less, in cases such as when anothervehicle cuts in front of you, or in other cases depending on visibility, thecondition of road surface and other factors*2, the function may be unable tostop the vehicle or may not activate. Pre-Collision Brake Assist also maynot activate depending on the conditions*2 listed below.*1:For vehicles: approximately 30 MPH (50 km/h),

For pedestrians: approximately 21 MPH (35 km/h)*2:Conditions- Distance to obstacle in front of you, speed difference, proximity condi-

tions, lateral displacement (the amount of offset)

D MN


Pre-Collision Braking System

21


- Vehicle conditions (amount of load, number of occupants, etc.)- Road conditions (grade, slipperiness, shape, bumps, etc.)- When visibility ahead is poor (rain, snow, fog or smoke, etc.)- When the detected object is something other than a vehicle, motorcycle,

bicycle or pedestrian• A domestic animal or other animal (a dog or deer, etc.)• A guardrail, telephone pole, tree, fence or wall, etc.

- Even if the obstacle is a motorcycle, bicycle or pedestrian, depending onthe brightness of the surroundings as well as the relative movement, andaspect or angle of the object, there may be cases when the system can-not detect it.

- When the system determines that operation by the driver (based onaccelerator pedal operation, braking, steering wheel angle, etc.) isintended as evasive action

- Vehicle maintenance status (brake systems, tire wear, tire pressure,whether a temporary spare tire is being used, etc.)

- When towing a trailer or another vehicle, etc.- When the brakes are cold due to outside temperature being low or just

after starting the engine.- When the brakes are overheated on downhill grades (braking effective-

ness is reduced)- When driving in rain or after washing the vehicle (the brakes are wet and

braking effectiveness is reduced)- Recognition conditions of the stereo cameras

In particular, the function may be unable to stop the vehicle or may notactivate in the following cases.• Bad weather (for example heavy rain, a blizzard or thick fog)• When visibility is poor due to sand, smoke or water vapor in the air or

when the vehicle in front or oncoming traffic causes water, snow, dirt,dust or other substances to obscure the view through the windshield

• When driving at night or in a tunnel without the headlights on• When driving at night or in a tunnel when there is a vehicle in front that

does not have its taillights on• When approaching a motorcycle, bicycle or pedestrian at night• When ambient light is poor in the evening or early morning• When a vehicle, motorcycle, bicycle or pedestrian is outside the area

illuminated by the headlights• When affected by strong light from the front (for example, sunlight at

dawn, sunset or headlight beams, etc.)• When there is snow, frost, dirt or dust on the windshield or it is clouded• When fluid has not been fully wiped off the windshield during or after

washer use• When the target cannot be correctly recognized because the stereo

cameras’ view is obstructed by water droplets from rain or the windowwasher, or by the wiper blades.



22


• When the stereo cameras’ field of view is obstructed (for example by acanoe on the roof of the vehicle)

• When the rear aspect ofthe vehicle in front islow, small or irregular(the system may recog-nize another part of thevehicle as its rear andwill determine operationfrom that)- When there is an

empty truck or trailerwith no rear and/orside panels on thecargo bed

- With vehicles that have cargo protruding from their back ends- With non-standard shaped vehicles (vehicle transporters or vehicles

with a sidecar fitted, etc.)- When the height of the vehicle is low, etc.

• When there is a wall, etc. in front of a stopped vehicle• When there is another object near the vehicle• When a vehicle, etc. has it’s side facing you.• With vehicles that are backing up or with oncoming vehicles, etc.• When the size and height of an obstacle is smaller than the limitations

of the stereo cameras’ recognition capability- With small animals or children, etc.- With pedestrians who are sitting or lying down

• When the detectedobject is a fence or wall,etc. with a uniform pat-tern (a striped pattern orbrick pattern, etc.)

• When there is a wall ordoor made of glass or amirror in front

• When the vehicle in frontsuddenly swerves, accel-erates, or decelerates.

• When a vehicle, motor-cycle, bicycle or pedes-trian suddenly cuts infrom the side or sud-denly runs in front of you.

S02061

S00653



23

• When you suddenly change lanes and your vehicle is immediatelybehind an obstacle

• When there is a vehicle, motorcycle, bicycle or pedestrian in a locationclose to your vehicle’s bumper

• When the speed difference between your vehicle and an obstacle is 4MPH (5 km/h) or less (As braking is performed once the obstacle is inclose proximity to your vehicle, depending on the shape and size of theobstacle, there may be some cases when the obstacle is outside therange of the cameras’ field of vision.)

• When driving on sharp curves, steep uphill grades or steep downhillgrades

• When driving on a bumpy or unpaved road• When there are changes in brightness, such as at a tunnel entrance or

exit• Do not test Pre-Collision Braking System on its own. It may operate

improperly and cause an accident.• The system may not operate correctly under the conditions listed below.

When these conditions occur, turn off the Pre-Collision Braking System.- The tire pressure is not correct.*1- The temporary spare tire is installed on any wheel.*1- Tires that are worn or have large variations in wear conditions are

installed.*1- Tires other than those of the designated size are installed.*1- Flat tires have been fixed temporarily with a tire repair kit.- The suspension has been modified (including a genuine SUBARU sus-

pension that has been modified).- Any object that disturbs the stereo cameras’ view is installed on the vehi-

cle.- The headlights are dirty or they have snow and ice or dirt on them.


minated and are difficult to detect.)- The lights including headlights and fog lamps have been modified.- Vehicle operation has become compromised due to an accident or mal-

function.- The brake system warning light is illuminated in red.- A heavy cargo is loaded onto or inside the vehicle.- The maximum number of occupants is exceeded.- There is something wrong with the combination meter; such as when the






24

CAUTION• In the following situations, turn off the Pre-Collision Braking System. Other-

wise the Pre-Collision Braking System may activate unexpectedly.- When the vehicle is being towed- When loading the vehicle onto a carrier- When a chassis dynamometer, free-rollers or similar equipment is used- When a mechanic lifts up the vehicle, starts the engine and spins the

wheels freely- When passing hanging banners, flags or branches, or when thick/tall vege-

tation is contacting the vehicle- When using a drive-through

car wash

• The Pre-Collision Braking System may activate in the following situations.Therefore concentrate on safe driving.

- When passing through an automatic gate (opening and shutting)- When driving close to the vehicle in front- When driving in a location where the grade of the road changes rapidly

- When visibility is poor due to sand, smoke or water vapor in the air, or whenthe vehicle in front or oncoming traffic causes water, snow, dirt or other sub-stances to obscure the view

- When passing through clouds of steam or smoke, etc.

S00656

S01264



25

- When the exhaust gas emitted by the vehicle in front is clearly visible in coldweather, etc.

- When there is an obstacle ona curve or intersection

- When narrowly passing avehicle or an object

- When stopping very close toa wall or a vehicle in front

• If there is cargo or installedaccessories, etc. that are pro-truding over the edge of thefront bumper, the vehicle’slength will increase and thesystem may not be able to pre-vent a collision.

• If the driver operates the brake pedal during automatic braking, the pedal mayfeel stiff; however, this is normal. By depressing the brake pedal further youcan apply more braking force.

NOTESome unusual noises may be audible during automatic braking. This iscaused by the braking control and is normal.

S00652

S01973



26

■ Detection of pedestriansThe EyeSight system can also detectpedestrians. The EyeSight system detectspedestrians from their size, shape andmovement. The system detects a pedestrianwhen the contour of the head and shouldersare clear.

WARNING

The EyeSight system’s Pre-Collision Braking function also treats pedestriansas obstacles. However, depending on the conditions, there may be caseswhen the system cannot detect a pedestrian. In the following conditions, thepossibility that the system may not be able to detect a pedestrian as an objectis particularly high.• When pedestrians are walking in a group• When a pedestrian is next to a wall or other obstacle• When a pedestrian is using an umbrella• When a pedestrian is wearing clothes that are a similar color to the sur-

rounding environment• When a pedestrian is carrying bulky luggage• When a pedestrian is bent over, crouching down or lying down• When a pedestrian is in a dark location• When a pedestrian suddenly crosses in front of you from the side or sud-

denly runs in front of you

Approx3 1/3 ft - 6 2/3 ft(1-2 m)

S00693



27

When there is an obstacle in the forward direction during driving, the system activates in thefollowing sequence in order to warn the driver, activate braking control, and active the brakelights.

Following Distance Warning:When the system determines that there is a risk of collision, a buzzer sounds repeated shortbeeps and the indicators on the multi information display illuminate to warn the driver.The Following Distance Warning operates when Adaptive Cruise Control is not set.When the driver depresses the brake pedal to decelerate and achieves a suitable followingdistance, the warning is canceled.

First Braking and Warning:When the system determines that there is a high risk of collision with an obstacle in front, abuzzer sounds repeated short beeps and the indicators on the multi information display illu-minate to warn the driver, and braking control is activated and the engine output, in somesituations, is also controlled. If the system determines that the amount of evasive action(braking, steering, etc.) taken by the driver has reduced the risk of collision, braking activa-tion is canceled.

Secondary Braking and Warning:If the system then determines that the risk of collision is extremely high, the buzzer changesto a continuous beeping sound and stronger braking control is activated. If, despite any eva-sive action taken by the driver, the system subsequently determines that a collision isunavoidable, braking control and the engine output control are continued.Even after the vehicle has stopped, depress the brake pedal.

<Apply Brake message>Until the brake pedal is depressed, a mes-sage appears and stays in the pop-up screenarea of the multi information display forapproximately 2 minutes. A single continuousbeep sounds while the message is displayed.

Pre-Collision Braking System operation

S01124

Apply Brake To Hold Position



28

NOTE• After the vehicle has come to a stop through secondary braking, release

brake control in the following manner.- Depress the brake pedal.- Depress the accelerator pedal (except when the select lever is in the

position).- When the selector lever is in the position

• After stopping with secondary braking, in the following cases, operate elec-tronic parking brake and release brake control.(For details about how to release the electronic parking brake, refer to theOwner’s Manual for your vehicle.)

- When approximately 2 minutes have elapsed since stopping and notdepressing the brake pedal

- When any door (except the rear gate/trunk) was opened- When EyeSight is temporarily stopped- When there is a malfunction in the EyeSight system

& warningSecondary braking

& warningFirst braking

Possible collision area Highly possiblecollision area

Extremely highly possiblecollision area

Obstacle

Firstbraking

No brake control Repeatedshort beeps

Repeatedshort beeps

StrongSecondarybraking

Operatingsystem

Indication on the multi information display

Continuousbeep

Moderate

Strength ofAutomatic Braking

Warning buzzer type

Following distance warning

Following distance warning

S01141

N

P



29

When the Pre-Collision Braking System is activated (when the system determines that thereis a high risk of collision with an obstacle in front), if the driver depresses the brake pedal,the system determines that this is emergency braking and activates braking assist automat-ically.

• Neither first braking or secondary braking will operate in the followingcases.

- When your vehicle speed is approximately 1 MPH (1 km/h) or less(When the selector lever is in the position and your vehicle speed isapproximately 2 MPH (4 km/h) or less) or 100 MPH (160 km/h) or more

- When Vehicle Dynamics Control is active• If the system detects the brake lights of the vehicle in front, your vehicle

will start decelerating earlier than if it does not.• There are some cases where the first braking is applied for a longer period

of time. One of the reasons for this is due to a large speed difference withan obstacle in front. In those cases, stronger or weaker braking controlmay be activated.

Pre-Collision Braking Assist operation

CAUTIONIf the driver depresses the brake pedal manually while following distancewarning is activated, the Pre-Collision Braking Assist will not work. (The vehi-cle decelerates with the normal braking force operated by the driver.)

NOTE• Pre-Collision Braking Assist function does not operate when the vehicle

speed is approximately 7 MPH (10 km/h) or less or 100 MPH (160 km/h) ormore.

• For information about the braking assist function, refer to the Owner’sManual for your vehicle.

N



30

Pressing and holding the Pre-Collision Braking System OFF switch for approximately 2 sec-onds (or longer) turns off the Pre-Collision Braking System (including Pre-Collision BrakeAssist). When 1 short beep sound emits, this control is turned off and the Pre-CollisionBraking System OFF indicator light on the instrument panel illuminates. To turn the control back on, press and hold the Pre-Collision Braking System OFF switch forapproximately 2 seconds or longer again. When this control is turned on, the Pre-CollisionBraking System OFF indicator light turns off.

Turning off the Pre-Collision Braking System

NOTE• When the Pre-Collision Braking System is turned off, the Pre-Collision

Throttle Management Control function is also turned off.• Even when the Pre-Collision Braking System is turned off, if the ignition

switch is turned off and the engine is then restarted, the Pre-CollisionBraking System will be turned on. The system default setting when thevehicle is restarted in “ON”.

S01120



31

■ Pre-Collision Braking System OFF indicator lightThis indicator light illuminates when the igni-tion switch is turned to the ON position, andremains illuminated for approximately 7 sec-onds after the engine starts. It turns on whenthe Pre-Collision Braking System is turned off.It also illuminates under the following condi-tions.• When the EyeSight system has a malfunc-

tion⇒ Refer to page 86.

• When the EyeSight system has stoppedtemporarily⇒ Refer to page 87.

NOTEWhen the Pre-Collision Braking System OFF indicator light is turned on, thePre-Collision Braking System (including the Pre-Collision Braking Assistfunction) does not operate.

S01121


32

Adaptive Cruise ControlAdaptive Cruise Control is a driving support system intended to allow more comfortable driving onexpressways, freeways and interstate highways. The vehicle in front in the same traffic lane isdetected by means of the stereo cameras, and your vehicle tracks the vehicle in front (up to themaximum speed of the set vehicle speed) while automatically maintaining a following distance thatcorresponds to the speed of the vehicle in front. Through operation of the electronic parking brake,the system uses the vehicle’s conventional braking system to stop your vehicle when the vehiclein front is stopped. The vehicle is capable of being controlled at a speed between approximately 0and 90 MPH (145 km/h). Please remember that you should not exceed posted speed limits.

WARNING

• This system does not provide the driver with an automatic driving functionthat handles all traffic conditions.

• Do not rely excessively on Adaptive Cruise Control. This system is not intendedto assist in driving when the driver is not paying full attention to what is ahead ofhim/her due to distractions or a lack of concentration while driving, or underconditions of poor visibility. It is not intended to prevent rear-end collisions.Strive for safe driving at all times. Always maintain a safe following distancebehind the vehicle in front of you, pay attention to your surroundings and thedriving conditions, and operate the brake pedal and take other action as neces-sary.

• Set the set vehicle speed within a range that is appropriate to the road con-ditions and surrounding environment.

• Before using the system, perform a daily inspection and verify that thereare no malfunctions of the tires or brakes.⇒ Refer to the separate “Warranty and Maintenance Booklet”.

• The system may not operate correctly under the conditions listed below.When these conditions occur, do not use Adaptive Cruise Control.

- The tire pressure is not correct.*1- The temporary spare tire is installed on any wheel.*1- Tires that are worn or have large variations in wear conditions are installed.*1- Tires other than those of the designated size are installed.*1- Flat tires have been fixed temporarily with a tire repair kit.- The suspension has been modified (including a genuine SUBARU sus-

pension that has been modified).- Any object that disturbs the stereo cameras’ view is installed on the vehicle.- The headlights are dirty or they have snow and ice or dirt on them.


minated and are difficult to detect.)- The lights including headlights and fog lamps have been modified.- Vehicle operation has become compromised due to an accident or malfunction.- The brake system warning light is illuminated in red.- A heavy cargo is loaded onto or inside the vehicle.- The maximum number of occupants is exceeded.- There is something wrong with the combination meter; such as when the





Adaptive Cruise Control

33


• Adaptive Cruise Control is designed for use on expressways, freeways, tollroads, interstate highways and similar limited access roads. It is not intendedto be used in city traffic. In the following conditions, do not use AdaptiveCruise Control. Doing so may result in an accident.

- Ordinary roads (roads other than those mentioned above)Depending on the driving environment (complexity of roads and other fac-tors), the system may not be able to perform as the traffic conditionsrequire, and that may result in an accident.

- Roads with sharp curves or winding roads- Frozen roads, snow-covered roads or other slippery road surfaces- The tires may spin, causing loss of control of the vehicle.- Traffic conditions when frequent acceleration and deceleration make it diffi-

cult to maintain the following distanceIt may not be possible for the system to perform as the traffic conditionsrequire.

- Steep downhill gradesThe set vehicle speed may be exceeded.

- On a steep continuous downhill gradeThe brakes may overheat.

- Roads and overpasses with repeated steep uphill and downhill gradesDetection of the vehicle in front may be lost, or the road surface may bedetected instead of the vehicle in front, making correct control impossible.

- When entering a sharp curve into an interchange or junction, or a servicearea, parking area, toll booth or other facilitiesDetection of the vehicle in front may not be possible.

- When there are changes in brightness, such as at a tunnel entrance or exit- When visibility is poor due to sand, smoke or water vapor blowing in the

wind, or when the vehicle in front or oncoming traffic causes water, snow,dirt or dust to obscure the viewDetection of the vehicle in front may be lost, or water or other substancesmay be incorrectly detected instead, making correct control impossible.

- When there is snow, frost, dirt or dust on the windshield or it is clouded

S00652



34


- When water droplets from rain or the window washer, or dirt has notbeen fully wiped off the windshieldIt may not be possible to detect the vehicle in front, making correct con-trol impossible.

- When the stereo cameras’ field of view is obstructed (for example by acanoe on the roof of the vehicle)

• The stereo cameras may have difficulty detecting the following objects orconditions. Operate the brake pedal and take other actions as necessary.

- Vehicles at significantly different speeds (vehicles driving slowly,stopped or oncoming vehicles, etc.)

- Vehicles cutting into your lane- Motorcycles, bicycles, pedestrians and animals, etc.- When light is poor in the evening or early morning- When driving at night or in a tunnel without the headlights on- When driving at night or in a tunnel when there is a vehicle in front that

does not have its taillights on- When affected by strong light from the front (sunlight or headlight high

beams, etc.)- Vehicles in front that have

a rear aspect that is low,small or irregular (the sys-tem may recognizeanother part of the vehicleand will determine opera-tion from that)• An empty truck or trailer

that has no cargo in thecargo bed being affectedby wind

• Vehicles that have cargoprotruding from theirback ends

• Non-standard shaped vehicles (vehicle transporters or vehicles with asidecar fitted, etc.)

• Vehicles that are low- Objects that are located close to the bumper of your vehicle

• When you do not want to use Adaptive Cruise Control, be sure to turn the (CRUISE) switch off. If the switch is left on, cruise control may be

accidentally engaged, possibly resulting in an accident.• Before using Adaptive Cruise Control, be sure to fully verify the safety of

the vehicle occupants and the area around the vehicle. Never operate thecruise control from outside the vehicle.

S02061



35


Detection of the vehicle in front by the EyeSight stereo cameras• Under the following road conditions or conditions of your vehicle, detection

of the vehicle in front may not be possible. Vehicles in neighboring trafficlanes or roadside objects may also be incorrectly detected. Under condi-tions such as these, do not use Adaptive Cruise Control. If cruise control iscurrently in use, operate the brake pedal and take other action as neces-sary.

- When tracking begins froma short following distance,such as when the vehiclein front is a vehicle that cutinto your lane

- When driving on curvedroads, at the start and endof a curve and on roadswith continuous curves(These conditions make itdifficult for the system todetect vehicles becausethey are outside thedetectable area.)

- When driving on an on-ramp or off-ramp to a free-way, highway, or otherrestricted access road(EyeSight Adaptive Cruise Control is not designed for use in this kind ofdriving environment.)

- When driving in an urban, or suburban environment (Adaptive CruiseControl is not appropriate for use in these driving areas. Adaptive CruiseControl should only be used on limited-access highways.)

S01975

S01976



36


- When the vehicle in front isnot directly ahead of yourvehicle and is shifted toone side

- When there is an obstacleat the side of the road

- When the relative speeddifference compared to thevehicle in front is large

- When a vehicle cuts intoyour lane in front of you

- When the distance betweenvehicles is extremely short

- When your vehicle is drift-ing within the lane

- When driving on a bumpyor unpaved road surface

- When driving on a roadwith extremely narrow lanes, such as when traffic restrictions are ineffect or in areas where construction work is taking place

- When normal driving has become compromised due to an accident ormalfunction

- When extremely heavy cargo is loaded in the cargo area, rear seat ortrunk of your vehicle

• There are limits to the capabilities of Adaptive Cruise Control. Even whenthe vehicle in front is detected, the system may not be able to decelerate intime in cases such as when the difference in speeds is large or when thevehicle in front decelerates suddenly. Operate the brake pedal and decel-erate as necessary.

• If the buzzer sounds frequently, do not use Adaptive Cruise Control.• Even when the following distance is short, the “brake more” warning may

not activate in the following cases.- When the relative speed difference compared to the vehicle in front is

small (the two vehicles are travelling at almost the same speed)- When the vehicle in front is traveling faster than your vehicle (the follow-

ing distance is gradually increasing)- When another vehicle cuts into your lane very close to your vehicle- When the vehicle in front decelerated suddenly- When there are repeated uphill and downhill grades

S01977

S01978



37

CAUTION• After Adaptive Cruise Control has started, it maintains control continuously

according to the behavior of the vehicle in front. When your vehicle comesto a stop if the vehicle in front has stopped, the stay-stopped function isengaged. However, if the EyeSight stereo cameras lost detection of thevehicle in front, the system may not stop your vehicle. Operate the brakepedal and maintain the correct following distance as necessary. Be awarethat the EyeSight system has difficulty detecting objects or vehicles thathave a relative speed in comparison to your vehicle. Therefore, if theEyeSight system loses detection just as you are approaching a line ofstopped cars, for example - you will have to brake manually.

• There is no possibility that the vehicle will automatically begin moving froma stay-stopped condition without operation from the driver.

• If the conditions for automatically canceling cruise control (⇒ refer to page49) are met while the vehicle is stay-stopped, Adaptive Cruise Control iscanceled and for safety reasons, the electronic parking brake is automati-cally applied.

• Braking may not be sufficient depending on the following conditions. Oper-ate the brake pedal and decelerate as necessary.

- Vehicle conditions (amount of load, number of occupants, etc.)- Road conditions (grade, slipperiness, shape, bumps, etc.)- Vehicle maintenance status (brake systems, tire wear, air pressure, tem-

porary spare tire is being used, etc.)- When the brakes are cold. (For example, just after the engine is started

or when the outside temperature is low.)- For a short period of time when driving after the engine is started until the

engine has warmed-up- When the brakes are overheated on downhill grades (braking effective-

ness may be reduced)- When driving in rain or after washing the vehicle (the brakes may

become wet and braking effectiveness may be reduced)- When towing a trailer or another vehicle, etc.



38

Adaptive Cruise Control is available when the engine is turned on.

■ Setting Adaptive Cruise Control(1) Setting Adaptive Cruise Control to standby statusPress the (CRUISE) switch. At this time, “ ” (Adaptive Cruise Control), your vehi-cle indicator and the “following distance setting” are displayed on the EyeSight display areain the multi information display.The set vehicle speed display will read “- - MPH”.

If the switch is pressed once more, the EyeSight display will turn off. It will also automaticallyturn off when the engine is stopped.To set ready status:

Adaptive Cruise Control can be set when allof the following conditions are met and is displayed on the EyeSight display area.- All doors (except the rear gate/trunk) are

closed.- The driver’s seatbelt is fastened.- The electronic parking brake is not

engaged (The brake system warning lightis turned off.).

- The selector lever is in the positionand the paddle shift is not operated.

- The brake pedal is not depressed.- EyeSight operation is not temporarily stopped.⇒ Refer to page 87.- The road is not a steep slope.- The steering wheel has not been turned significantly in either direction.- X-mode is not turned on.- The vehicle speed is between approximately 0 MPH (0 km/h) and 90 MPH (145 km/h).

How to use Adaptive Cruise Control

S01985 S01110

S01111D



39

(2) Setting Adaptive Cruise ControlPress the RES/SET switch to the “SET/-”.Adaptive Cruise Control is now set, and cruisecontrol will start.If no vehicle in front has been detected, thevehicle drives at the constant set targetspeed.When Adaptive Cruise Control is set, the setspeed and are displayed on the EyeSightdisplay area.

NOTE• The target vehicle speed can be set between 25 MPH (40 km/h) and 90

MPH (145 km/h).• If the vehicle speed is approximately 25 MPH (40 km/h) or less when the

vehicle speed is set, the set vehicle speed is set to 25 MPH (40 km/h).• When driving on a curve, the vehicle may not accelerate, or may deceler-

ate, even if the set speed is higher than the current vehicle speed.

S01986

S01114



40

When a vehicle in front is detected, a buzzersounds 1 short beep and the lead vehicle indi-cator will illuminate. (white) will turngreen.The vehicle tracks the lead vehicle in frontand maintains the selected following distance.At this time, the speed upper limit is the setvehicle speed. If the vehicle in front is no lon-ger detected, a buzzer sounds 1 short beepand the lead vehicle indicator turns off. (green) will turn white.

Operation of Adaptive Cruise Control• When no vehicle in front is detected

The vehicle drives constantly at the set tar-get vehicle speed between approximately25 MPH (40 km/h) and 90 MPH (145 km/h).

• When a vehicle in front is detectedThe vehicle tracks the lead vehicle in front,and will maintain the chosen following dis-tance (there are four settings), up to the settarget vehicle speed - between 25 MPH (40km/h) and 90 MPH (145 km/h).

NOTEThe buzzer sound (lead vehicle acquisition sound) that occurs when a vehiclein front is detected or no longer detected while Adaptive Cruise Control is setcan be turned off by customization.⇒ Refer to page 89.

S01113

S01979

S01980

本文.fm 40 ページ２０１５年５月２９日　金曜日　午後３時５２分


41

• If your vehicle no longer detects the vehiclein frontThe vehicle gradually accelerates back tothe set target vehicle speed and will drive atthat constant speed.If a vehicle in front is detected while accel-erating to the set target vehicle speed, vehi-cle tracking will be started again.

CAUTIONIf the driver operates the brake pedal during automatic braking, the pedalmay feel stiff; however, this is not a malfunction. By depressing the brakepedal further you can apply more braking force. When the brake pedal isreleased it will return to its original condition.

NOTE• When the brakes are applied by Adaptive Cruise Control, the vehicle’s

brake lights will illuminate.• Even if there is no lead vehicle present, on a downhill grade, the Adaptive

Cruise Control’s automatic brake may operate in order to maintain the settarget vehicle speed.

• Some noises may be audible during automatic braking. This is caused bythe braking control and does not indicate a malfunction.

• To temporarily accelerate quickly, use the accelerator pedal. After acceler-ating, the vehicle will gradually return to the set target vehicle speed shownin the gauge cluster.

• There are cases where the vehicle in front has turned off the road whileyour vehicle is still controlled by the automatic braking operation that hasactivated due to the deceleration of the vehicle in front of yours. In thosecases, the brake will be automatically released gradually. Depress theaccelerator pedal if necessary.

• The lead-vehicle tracking function has the following characteristics:- If the lead vehicle’s brake lamp is detected, deceleration is started more

quickly than without detection.- If the vehicle moves to the fast lane while travelling more than 37 MPH

(60 km/h), the system starts acceleration to the set vehicle speed morequickly because it is linked with the turn signal.

S01981



42

■ Increasing the set vehicle target speed●Using the RES/SET switch

Push the RES/SET switch in the followingway while you are driving with AdaptiveCruise Control on:• Push the RES/+ switch towards the position

(1) briefly: the set vehicle speed willincrease in increments of 1 MPH (1 km/h)every time the button is pushed.

• Push the RES/+ switch towards the position(1) for longer: the set vehicle speed willincrease in increments of 1 MPH (1 km/h)while the button is being pushed.

• Push the RES/+ switch towards the position (2) briefly: the set vehicle speed will increaseto the next 5 MPH (5 km/h) increment every time the button is pushed.

• Push the RES/+ switch towards the position (2) for longer: the set vehicle speed will increaseto the next 5 MPH (5 km/h) increment while the button is being pushed and will continue toadvance target speed in 5 MPH (5 km/h) increments as long as the button is pushed.

The set vehicle target speed is shown on the EyeSight display. Using this method, you can‘fine tune’ the vehicle’s set target speed.

●Using the accelerator pedalDepressing the accelerator pedal will increase vehicle speed. Once the preferred speed hasbeen attained, push the RES/SET switch to SET/-. When the switch is pressed, the newvehicle target speed will be set. The new set vehicle speed will be displayed in the EyeSightdisplay area.

CAUTION• When Adaptive Cruise Control is operating, the actual vehicle speed is

controlled according to the lead vehicle. Therefore, if the RES/SET switchis pressed to the “RES/+” and set to a speed higher than the speed of thelead vehicle, the vehicle will not accelerate - it will maintain a safe followingdistance as the first priority. However, because doing so changed the setvehicle target speed, when the lead vehicle is no longer detected (forexample, if you change to a freeway lane with no vehicles in front), thevehicle will accelerate to that new set target speed. Change the set vehicletarget speed while briefly checking the value shown in the set speed dis-play on the EyeSight display.

• When the accelerator pedal is depressed with Adaptive Cruise Control on,automatic braking control and warnings by Adaptive Cruise Control will notoccur. However, if there is a high risk of collision with an obstacle in front ofthe vehicle at this time, the warning and braking control of the Pre-CollisionBraking System may activate.

S01990



43

■ Decreasing the set vehicle target speed●Using the RES/SET switch

Push the RES/SET switch in the followingway while you are driving with AdaptiveCruise Control on:• Push the SET/- switch towards the position

(1) briefly: the set vehicle speed willdecrease in increments of 1 MPH (1 km/h)every time the button is pushed.

• Push the SET/- switch towards the position(1) for longer: the set vehicle speed willdecrease in increments of 1 MPH (1 km/h)while the button is being pushed.

• Push the SET/- switch towards the position (2) briefly: the set vehicle speed will decreaseto the next 5 MPH (5 km/h) decrement every time the button is pushed.

• Push the SET/- switch towards the position (2) for longer: the set vehicle speed willdecrease to the next 5 MPH (5 km/h) decrement while the button is being pushed and willcontinue to lower target speed in 5 MPH (5 km/h) decrements as long as the button ispushed.

The set vehicle target speed is shown on the EyeSight display.

●Using the brake pedal(1) Depress the brake pedal to decrease the vehicle speed. (Adaptive Cruise Control will be

canceled and will be turned off.)(2) When the desired speed is reached, press the RES/SET switch to the “SET/-”. The

speed at the time of pressing the switch will be set as the new vehicle speed, and itappears in the EyeSight display area.

■ Accelerating temporarilyDepress the accelerator pedal to accelerate temporarily.When the accelerator pedal is released, the vehicle returns to the set vehicle speed.

S01991



44

■ Decelerating temporarilyDepress the brake pedal to decelerate tempo-rarily. When the brake pedal is depressed,Adaptive Cruise Control will be canceled. The

will be turned off while the set vehicle tar-get speed remains displayed on the EyeSightdisplay area.Release the brake pedal and press theRES/SET switch to “RES/+” to reset the setvehicle target speed.

CAUTIONOrdinarily, while Adaptive Cruise Control is functioning, acceleration anddeceleration are performed automatically according to the speed of the leadvehicle (if one is detected). However, when your vehicle approaches a leadvehicle, for example if it is necessary to accelerate for a lane change or otherreason, and if the vehicle in front suddenly decelerates, or if another vehiclecuts into your path, operate the accelerator pedal or brake pedal and acceler-ate or decelerate as appropriate for the existing conditions.

S01117

will be turned off.



45

■ Changing the following distance from the vehicle in frontThe following distance from the vehicle in front setting can be changed in 4 stages.

: When the switch ( side) is pressed, the following distance will be longer.: When the switch ( side) is pressed, the following distance will be shorter.

NOTE• The following distance changes according to the vehicle speed and is fur-

ther the faster that the vehicle is traveling at.<Approximate guide to following distances>

• If you turn the (CRUISE) switch off, then turn it on again, the follow-ing distance which was set before turning the switch off will be maintained.

S01992

Following distance indicator

When you vehicle speed is 25 MPH (40 km/h)

When you vehicle speed is 60 MPH (100 km/h)

Approx. 95 ft (30 m) Approx. 190 ft (60 m)






46

■ Stay-stopped functionIf the vehicle in front comes to a stop while you are utilizing Adaptive Cruise Control, yourvehicle will also come to a stop and will stay stopped.When your vehicle comes to stop after the vehicle in front has stopped, Adaptive CruiseControl is paused and the stay-stopped function is engaged. on the EyeSight displayarea is turned off and is displayed. At the same time, is turned back to white.

●Resuming Adaptive Cruise Control in stay-stopped status▼Setting using the RES/SET switch

Press “SET/-” (⇒ Refer to page 39 “(2) Setting Adaptive Cruise Control”.)Press “RES/+” (⇒ Refer to page 51 “Returning to a vehicle speed that was previouslyset”.)

▼Setting with the accelerator pedalDepressing the accelerator pedal while stay-stopped is engaged cancels stay-stoppedstatus. At this time, Adaptive Cruise Control is resumed. The vehicle will attempt to travelat the previously set vehicle target speed unless a lead vehicle is detected. If a lead vehi-cle is detected, Adaptive Cruise Control will maintain the previous following distance set-ting.

NOTEWhen Adaptive Cruise Control is resumed from stay-stopped status and thevehicle in front accelerates, your vehicle will also accelerate and continue totrack the vehicle in front at the previously set following distance. However, ifthe lead vehicle does not start moving or pauses, stay-stopped status will beautomatically restored after approximately 3 seconds.

NOTEIf the accelerator pedal is only slightly depressed, the stay-stopped functionmay not be canceled, and the Adaptive Cruise Control may not be resumed.

S01982 S01140



47

●Canceling the stay-stopped functionIf any of the following operations is performed, the stay-stopped function will be canceledand the Adaptive Cruise Control will be canceled at the same time.• The brake pedal is depressed.• The (CRUISE) switch is pressed.• The electronic parking brake switch is pressed to apply the Electronic Parking Brake.

●Setting Adaptive Cruise Control while the Electronic Parking Brake is appliedIf the Electronic Parking Brake is applied, then before setting cruise control, release theElectronic Parking Brake by depressing the accelerator pedal or by other specifiedmeans. For details of how to release the electronic parking brake, refer to the Owner’sManual for your vehicle.

WARNING

• While the stay-stopped function is engaged, do not exit the vehicle.• The stay-stopped function is not a replacement for engaging the parking

brake.When parking, always apply brakes manually to come to a full stop, thenset the electronic parking brake.

CAUTIONThe stay-stopped function of cruise control will be canceled under the follow-ing conditions:• The vehicle is in stay-stopped mode for approximately 2 minutes or more.

(A buzzer will sound 5 intermittent beeps and 1 long beep.)• Any condition in which automatic cancellation is met. (A buzzer sounds 1

long beep.)⇒ Refer to page 49.After the stay-stopped function has been canceled, the Electronic ParkingBrake will be automatically applied and the brake system warning light willilluminate. However, if any canceling condition for the Electronic ParkingBrake (i.e. the interlock system with the accelerator pedal, switch operation ofthe electronic parking brake, etc.) is fulfilled, the Electronic Parking Brake willnot work. (For details, refer to the Owner’s Manual for your vehicle.) If the accelerator pedal is only slightly depressed while the stay-stopped func-tion is activated, the stay-stopped function of cruise control may be canceled,and the Electronic Parking Brake may not work.



48

■ Canceling Adaptive Cruise Control●Canceling by driver operation

Either of the following operations will cancel Adaptive Cruise Control.

• Depress the brake pedal. will be turned off while the set vehicle

target speed remains displayed on theEyeSight display area.

• Press the (CRUISE) switch. will be turned off while the set vehicle

target speed remains displayed on theEyeSight display area.When the (CRUISE) switch ispressed again, will be turned off andAdaptive Cruise Control will be turned off.

S01117

will be turned off.

S01985



49

●Automatic cancellation by the systemIn the following cases, a buzzer will sound asingle long beep and Adaptive CruiseControl is automatically canceled. ( isdisplayed on the EyeSight display area.) Ifthe stay-stopped function is engaged, theelectronic parking brake will be automati-cally engaged.

• Conditions for automatic cancellation- The grade of the road is very steep.- ABS, Vehicle Dynamics Control or Traction Control Function is activated.- The vehicle speed has exceeded approximately 100 MPH (160 km/h) while cruise con-

trol is set.- The steering wheel was turned significantly in either direction.- The transmission select lever is moved to a position other than .

• Cruise control can be resumed after the transmission select lever is returned to the position.

- A paddle shift switch is operated while driving when the transmission select lever is inthe position.• Cruise control can be resumed again after the shift indicator returns to .

- Any door (except the rear gate/trunk) is opened.- The driver’s seatbelt is unfastened.- The electronic parking brake is engaged manually. (When the brake system warning

light is illuminated or flashing.)- The X-mode is turned on (the X-mode indicator light illuminates).

• Cruise control can be resumed after the X-mode is turned off.- EyeSight operation has temporarily stopped.

⇒ Refer to page 87.- EyeSight is malfunctioning.

⇒ Refer to page 86.- The Pre-Collision secondary braking has activated.

S01265

D

D

DD



50

WARNING

Do not use Adaptive Cruise Control on slippery roads. Doing so may result inan accident.

CAUTIONWhen shifting the selector lever to the position, Adaptive Cruise Controlwill be automatically canceled. Do not shift the lever to the position unlessit is an emergency. Otherwise the engine brake may not operate, which couldcause an accident.

NOTE• If EyeSight operation has temporarily stopped, the Pre-Collision Braking

System OFF indicator light and Lane Departure Warning OFF indicatorlight illuminate, and the EyeSight temporary stop indicator is displayed onthe multi information display.

⇒ Refer to page 87.• If EyeSight is malfunctioning, the EyeSight warning indicator is displayed

on the multi information display, and the Pre-Collision Braking SystemOFF indicator light and Lane Departure Warning OFF indicator light willalso illuminate. If this occurs, stop the vehicle in a safe location and thenturn off the engine and restart it. If the indicators remain illuminated afterrestarting the engine, Adaptive Cruise Control cannot be used. This will notinterfere with ordinary driving; however the system should be inspected bya SUBARU dealer as soon as possible.

⇒ Refer to page 86.• When the operation of Adaptive Cruise Control has been automatically

canceled, perform the set cruise control operation again after the conditionthat caused the cancellation has been corrected. If the cruise control func-tion cannot be set even after the condition has been corrected, EyeSightmay be malfunctioning. This will not interfere with ordinary driving; how-ever contact a SUBARU dealer and have the system inspected.

NN



51

■ Returning to a vehicle speed that was previously setThe vehicle speed which was previously set is stored in memory.* To return to set that vehi-cle speed, press the RES/SET switch to the RES/+. ( on the EyeSight display area illu-minates again to indicate that the system has returned to the set status again.)

NOTE*The vehicle speed stored in memory is erased in the following circum-stances:• The cruise control is turned off by pressing the (CRUISE) switch.• Vehicle Dynamics Control or Traction Control Function are activated.• The cruise control mode was switched from Adaptive Cruise Control to

Conventional Cruise Control.

S01993 S01114



52

■ “Brake more” warningThe “brake more” warning is activated while Adaptive Cruise Control is tracking a lead vehi-cle. This function warns the driver when it determines that the current level of decelerationby automatic braking control is insufficient.• When the ‘brake more’ function operates,

“Obstacle Detected” will be shown in thepop-up screen area of the multi informationdisplay, a lead vehicle indicator will flash,and a buzzer will sound several shortbeeps.

• When this function activates, depress thebrake pedal to decelerate and maintain acorrect following distance.

Other functions

WARNING

• If the buzzer sounds frequently, do not use Adaptive Cruise Control.• The “brake more” warning will not activate in the following situations.- The accelerator pedal is depressed.- The brake pedal is depressed.

• Even when the following distance is short, the “brake more” warning maynot activate in the following situations.

- The difference in speed with the vehicle in front is small. (The two vehi-cles are travelling at almost the same speed.)

- The vehicle in front is traveling faster than your vehicle. (The followingdistance is gradually increasing.)

- Another vehicle cuts into your lane very close to your vehicle.- The vehicle in front decelerates suddenly.- When there are repeated uphill and downhill grades

• The “brake more” warning may not activate in time in the case of a vehiclethat is stopped at the end of a line at a toll gate, at a stop light or intersec-tion or in traffic congestion, or a vehicle that is moving much slower thanyour vehicle. EyeSight requires a speed differential in order to recognize apotential obstacle and react to it.

S01119

ObstacleDetected



53

NOTE• Vehicles in front in the same traffic lane are detected by the stereo cam-

eras within a distance of approximately 360 ft (110 m) in the forward direc-tion. However the detection distance may be reduced depending on thetraffic environment, driving conditions, and conditions of the vehicle infront.

• If does not illuminate when the (CRUISE) switch is pressed,there may be a malfunction in the system. Contact a SUBARU dealer andhave the system inspected.


54

Lane Keep AssistThe stereo cameras detect lane markings(including Botts' dots) of the lane and the sys-tem assists the steering operation by workingwith the electric power steering to help keepyour vehicle in its lane when driving onexpressways, freeways and interstate high-ways.

WARNING

Lane Keep Assist is not an automatic driving system.Do not overestimate the capabilities of Lane Keep Assist. It is not a sys-tem to assist inattentive driving or meant to permit driving without hold-ing the steering wheel. Make sure to grip the steering wheel whiledriving. To drive safely, check the distance from the vehicle in front orfrom a vehicle driving in parallel with your vehicle, the surrounding con-ditions and the surrounding environment while driving.If you feel that the level of control and timing by the system are different fromyour own driving style, the system may not support safe driving. Do not useLane Keep Assist.Lane Keep Assist does not always operate under all situations. If you relyonly on the Lane Keep Assist to stay in a lane, it may cause an accident suchas a collision with an obstacle beside your lane or with a vehicle driving in anadjacent lane.• Check that there are problems with the tires and brakes during a daily

inspection before using the system.⇒ Refer to “Warranty and Maintenance Booklet”.• The system may not operate properly under the following conditions. Do

not use Lane Keep Assist.- The air pressure of tires is not to specification.*1- Tires that are worn or have large variations in wear conditions are

installed.*1- Tires other than those of the designated size are installed.*1- The wheel balance is abnormal (e.g., the balance weight is removed or

misaligned.)*1- The wheel alignment is not adjusted within the specified value.*1- Flat tires have been fixed temporarily with a tire repair kit.- The suspension has been modified (including genuine SUBARU parts).

S02069

Lane markings


Lane Keep Assist

55


- Any object that disturbs the stereo cameras’ view is installed on the vehi-cle.

- Tire chains are installed.- When you feel an abnormal vibration in the steering wheel or feel the

steering wheel is heavier than usual.- The steering wheel has been replaced with parts other than genuine

SUBARU parts.- The headlights are dirty or they have snow, ice or dirt on them. (Objects

are not adequately illuminated and are difficult to detect.)- The headlights are not aligned correctly. (Objects are not adequately illu-

minated and are difficult to detect.)- The headlights and fog lamps, and other lights, have been modified.- Vehicle operation has become compromised due to an accident or mal-

function.- The brake system warning light (red) is illuminated.- A heavy cargo is loaded onto or inside the vehicle.- The maximum number of occupants is exceeded. - Your vehicle is towing a vehicle, etc.- There is something wrong with the combination meter. For example, an

indicator light or a warning light in the combination meter does not prop-erly turn on or off, a beep does not sound, or the indication on the liquid-crystal display is different from when it is normal.*2*1: The wheels and tires have critically important functions. Be sure to

use the appropriate ones. For details, refer to the Owner’s Manual for your vehicle.

*2: For details about the functions and operations of the combinationmeter, refer to the Owner's Manual for your vehicle.

• Lane Keep Assist is designed for use on expressways, freeways, tollroads, interstate highways and similar limited access roads. In the follow-ing conditions, do not use Lane Keep Assist. Doing so may result in anaccident.

- Ordinary roads (roads other than those mentioned above)- Roads with sharp curves- Roads with lane restric-

tions or tentative lanes dueto construction work, etc.

- Old lane markings remain.- Snow, puddles or snow

melting agents remain onthe road surface.

- Cracks or constructedtraces remain on the roadsurface.

S02059


Lane Keep Assist

56


- Frozen roads, snow-covered roads or other slippery road surfacesThe tires may spin, causing loss of control of the vehicle.

- When entering a sharp curve into an interchange or junction, or a servicearea, parking area, toll booth or other facilities.

- When there are changes in brightness, such as at a tunnel entrance orexit.

- When visibility is poor due to sand, smoke or water vapor blowing in thewind, or when the vehicle in front or oncoming traffic causes water,snow, dirt or dust to obscure the view.

- When there is snow, frost, dirt or dust on the windshield or it is clouded.- When water droplets from rain or dirt have not been fully wiped off on the

windshield.It may not be possible to detect the lane, making correct control impossi-ble.

- When the stereo cameras’ field of view is obstructed (for example by acanoe on the roof of the vehicle).

- The stereo cameras may have difficulty detecting the objects under thefollowing conditions and the system may not operate properly.

- When driving at night or in a tunnel without the headlights on.- When light is poor in the evening or early morning.- In bad weather (for example, rain or snow)- The distance between your vehicle and the vehicle in front is short, mak-

ing it difficult to detect lane markings.- When a vehicle intruded from an adjacent lane or the vehicle in front

changed lanes.- The shape of a curve in the road suddenly changes.- Shadows of guardrails or similar objects are overlapped on the lane

markings.- When your vehicle is exposed to a strong light from the front (backlight

from the sun, headlights, etc.).- The width of a lane is narrow.- The stereo cameras may have difficulty detecting the lane due to the per-

formance of the cameras.• There are no lane markings or they are very worn.• The lane markings are painted in yellow.• It is difficult to detect lane markings because they are similar in color to

the road surface.• The lane markings are drawn in double.• The width of lane markings is narrow.• The indicated lines for the area are touched to walls and poles.

- The shape of lane markings suddenly changes (entrance/exit of a curve,crank and S-shaped road, etc.).

- There is curb or side wall in the road shoulder.- The brightness changes such as when you drive under an overpass.


Lane Keep Assist

57

CAUTION• The performance of Lane Keep Assist may not be optimal under the following

conditions. In addition, Lane Keep Assist may not operate or the operationmay be canceled.

- Immediately after the weight of your vehicle changes radically- Immediately after the replacement of a tire or the adjustment of tire pres-

sure- Immediately after the adjustment, repair or replacement of cameras or

related components- Immediately after the repair or replacement of the suspension or steering

system- A winter tire or a tire other than a genuine SUBARU tire is used.- The vehicle is in a crosswind.- The road grade abruptly changes (uphill or downhill).- The grade of the crossing direction in a road is large or changes abruptly.- Unevenness, winding and joint of a road surface- The acceleration/deceleration is high.- Immediately after starting the engine when the outside temperature is low.- The outside temperature is high.

• When you do not use Lane Keep Assist, make sure to turn off the (LaneKeep Assist) switch. If you turn it on, the function may operate unexpectedly,causing an accident.

• If you turn on the (Lane Keep Assist) switch, the operation power ofelectric power steering may change.


Lane Keep Assist

58

The system detects lane markings in order to help prevent departure from the lane. If youdrive on expressways, freeways or interstate highways at speeds above approximately 40MPH (65 km/h) and the vehicle is about to depart from the lane, the system assists thesteering operation by turning it to the direction that will help prevent the lane departure.

■ How to use Lane Departure Prevention FunctionPress the (Lane Keep Assist) switch.Lane Keep Assist is turned on, and “ ” (Lane Keep Assist indicator) (white) is displayedon the EyeSight display area of the multi information display.

Lane Departure Prevention Function

S02043

There is a strong possibility of lane departure.

There is a possibility of lane departure.

S01994 milesA

MPG

S02044

Lane Keep Assist indicator (white)


Lane Keep Assist

59

Press the (Lane Keep Assist) switch once again to turn it off, and “ ” (Lane KeepAssist indicator) is turned off on the EyeSight display area.

The Lane Departure Prevention Function goes into the standby status, and the lane indica-tor illuminates when all of the following conditions are met.• The vehicle speed is between approximately 40 MPH (65 km/h) and 90 MPH (145 km/h).• The system is detecting the lane markings.• The driver is holding the steering wheel.• When driving on a road that has a lane width that is between approximately 10 ft (3 m)

and 15 ft (4.5 m).• When driving on a straight road or gentle curve.• When driving near the center of a lane.

When the vehicle is about to depart from the lane, Lane Departure Prevention Functionstarts to operate and “ ” (Lane Keep Assist indicator) illuminates in green while it isoperating.

NOTE• If you just lightly put your hands on the steering wheel for a certain period

of time or if you do not operate the steering wheel, the function will auto-matically be canceled. (“ ” Lane Keep Assist indicator) illuminates inwhite again.)

• Lane Departure Prevention Function operates when the system deter-mines that the vehicle will depart from the lane if you continue to drive inthe same manner. Therefore, it operates at an earlier timing than LaneDeparture Warning (⇒ Refer to page 68.) (it may depend on the surround-ing environment and road condition).

• The lane indicator in the standby status and in operation may illuminateonly on the left side or right side.

milesA

MPG

milesA

MPG

milesA

MPG

S02045

Lane Keep Assist indicator (white)

Turned on Standby status In operation

(white) (green)


Lane Keep Assist

60

■ Canceling Lane Departure Prevention Function●Cancellation by the operation of a driver (In case no beep sounds)

The following operation cancels Lane Departure Prevention Function.If the function is canceled, “ ” (Lane Keep Assist indicator) and the lane indicator areturned off on the EyeSight display area.• Press the (Lane Keep Assist) switch.

Either of the following operations temporarily cancels the Lane Departure Prevention Function.While temporarily canceling the function, “ ” (Lane Keep Assist indicator) on theEyeSight display area illuminates in white and the lane indicator is turned off.• Depressing the brake pedal• Operating the turn signal lever• When the system determines that the driver operates the steering wheel to make a lane

change.• When the driver depresses the accelerator pedal deeply.• Turning on the hazard warning flasher switch

●Automatic cancellation by the system (An audible beep will sound.)Under the following conditions, a beep sounds and the Lane Departure Prevention Functionis temporarily canceled.While the function is temporarily canceled, “ ” (Lane Keep Assist indicator) on theEyeSight display area illuminates in white and the lane indicator is turned off.• When the system cannot detect the lane.• The windshield wiper operates at a high speed.• The vehicle speed is less than approximately 37 MPH (60 km/h) or is more than approxi-

mately 93 MPH (150 km/h).• The ABS, the Vehicle Dynamics Control or the Traction Control System operates.• Either the driver's door, the front passenger's door or the rear door is open.• The seatbelt of driver's seat is unfastened.• The electronic parking brake is applied (The electric parking brake indicator light illumi-

nates or blinks).• The select lever is shifted to a position other than or position.• The system could not detect the steering

operation by the driver for a certain period oftime.- When the system detected no steering

operation, the interruption screen appearson the multi information display. The inter-ruption screen continues to appear untilthe system detects the steering operation.If the system still cannot detect the steer-ing operation, the Lane Departure Preven-tion Function is automatically canceled.

D M

milesA

MPG

Keep Hands OnSteering Wheel

S02046

本文.fm 60 ページ２０１５年５月１５日　金曜日　午後１時４１分

Lane Keep Assist

61

• When entering a sharp curve.• When driving on a sharp curve.• When the system determines that the steering assistance is difficult to continue due to the

road condition.• When the system determines that the steering assistance is difficult to operate due to

another system.• When the EyeSight system is temporarily stopped. (“ ” (EyeSight Temporary Stop

indicator: White) is turned on.)⇒ Refer to page 86.• When the EyeSight system has a malfunction. (“ ” (EyeSight Warning indicator:

Yellow) is turned on.)⇒ Refer to page 87.

NOTEIf the function is automatically canceled during the standby status (“ ”(Lane Keep Assist indicator) illuminates in white), no beep sounds.


62

Pre-Collision Throttle ManagementWhen an obstacle is detected in front of thevehicle, and the vehicle is stopped or travel-ling very slowly, if the system determines thatthe accelerator pedal has been depressed bymore than the necessary amount (due todriver error), it greatly restricts engine outputand ensures that vehicle forward movement isslower than normal in order to give the driveradditional time to brake or react.

During system operation, a buzzer will soundseveral short beeps, and “Obstacle Detected”will be shown on the pop-up display area ofthe multi information display. The lead vehicleindicator will also flash.This function only activates when the trans-mission select lever is in the or posi-tion.

WARNING

Do not rely excessively on Pre-Collision Throttle Management. Pre-Collision Throttle Management is not designed to help you avoid colli-sions in many situations. Always check the selector lever and pedalpositions as well as the surrounding environment before starting andoperating the vehicle. Relying only on Pre-Collision ThrottleManagement could result in an accident.• Pre-Collision Throttle Management is not designed to maintain the vehicle

in a stopped condition.• Pre-Collision Throttle Management will not reduce acceleration under all

conditions. It is also not designed to prevent collisions.• Pre-Collision Throttle Management will operate when an obstacle is

detected in front. However, this function will not reduce acceleration incases where no obstacle is recognized (for example when approaching acliff, etc.)

• Do not intentionally depress the accelerator pedal excessively when thereare obstacles nearby. If the driver relies only on Pre-Collision ThrottleManagement to control acceleration, collisions may occur.

S01125

“Repeated short

beeps”

S01119

ObstacleDetected

D M


Pre-Collision Throttle Management

63


• If your vehicle is trapped on a railroad crossing and you are trying toescape by driving through the crossing gate, the stereo cameras may rec-ognize the crossing gate as an obstacle and Pre-Collision ThrottleManagement system may activate. In this case, remain calm and eithercontinue to depress the accelerator pedal or turn off the Pre-CollisionThrottle Management system.

⇒ Refer to page 67.• Pre-Collision Throttle Management may not activate depending on the fol-

lowing conditions:- The distance between your vehicle and the obstacle, speed difference,

and lateral displacement (amount of offset)- Recognition status of the stereo cameras

In particular, the function may not activate in the following cases:• Bad weather (for example heavy rain, a blizzard or thick fog)• When visibility is poor due to sand or smoke in the air• When light is poor in the evening, early morning, or at night• In a dark area (indoor parking area, etc.)• When there is an obstacle outside the area illuminated by the head-

lights• When affected by strong light from the front (for example sunlight at

sunrise or sunset headlight beams, etc.)• When there is snow, frost, dirt or dust on the windshield, or it is clouded• When fluid has not been fully wiped off the windshield during or after

use of the window washer• When obstacles cannot be correctly recognized due to water droplets

from rain or the washer, or the wiper blades obstructing the stereocameras’ field of view

• When the stereo cameras’ field of view is obstructed (for example by acanoe on the roof of the vehicle)

• With low obstacles (low wall, crash barrier, low vehicle, etc.)• When the size and height of an obstacle is smaller than the limitations

of the stereo cameras’ recognition capability• With small animals or children.• With pedestrians who are sitting or lying down

• When the rear portionnearest your vehicle istoo small or too close(such as a trailer oroncoming vehicle) thesystem may not recog-nize the part of thatvehicle which is closestto you.

S02063



64


• When there is a fence orwall, etc., with a uniformpattern (striped pattern,brick, etc.) or with no pat-tern in front

• When there is a wall ordoor made of glass or amirror in front

• When an obstacle (anothervehicle, motorcycle, bicy-cle, pedestrian, animal orchild, etc.) cuts in from theside or jumps out suddenly

• When starting, if you change lanes and your vehicle is immediatelybehind the obstacle

• On sharp curves, steep uphill grades or steep downhill grades- When the system determines that steering operation by the driver is

intended as evasive action• For your safety, do not test Pre-Collision Throttle Management on its own. It

may operate improperly and cause an accident.

S00653



65


CAUTION• In the following situations, turn off Pre-Collision Throttle Management. Other-

wise Pre-Collision Throttle Management may activate unexpectedly.- When the vehicle is being towed- When loading the vehicle onto a carrier- When a chassis dynamometer, free-rollers or similar equipment is used- When a mechanic lifts up the vehicle, starts the engine and allows the

wheels to spin freely- When passing hanging banners, flags or branches, or when thick/tall vege-

tation is contacting the vehicle• The Pre-Collision Throttle Management may activate in the following situa-

tions. Therefore concentrate on safe driving.- When your vehicle is close to the vehicle in front- When passing through an automatic gate- When your vehicle is in a location where the grade of the road changes

rapidly

- When passing through clouds of steam or smoke

S01264

S00652



66


- When there is an obstacle ona curve or intersection

- When narrowly passing avehicle or object

- When stopping very close toa wall or a vehicle in front

NOTE• When the accelerator pedal is depressed for approximately three seconds,

Pre-Collision Throttle Management will be released gradually.• When the Pre-Collision Braking System is turned off, Pre-Collision Throttle

Management is also turned off.⇒ Refer to page 30.

S01973



67

Pressing and holding the Pre-Collision Braking System OFF switch for approximately 2 sec-onds or longer will turn off the Pre-Collision Throttle Management System. When 1 shortbeep sound emits, this function is turned off and the Pre-Collision Braking System OFF indi-cator light on the instrument panel illuminates. To turn the system back on, press and hold the Pre-Collision Braking System OFF switchagain for approximately 2 seconds or longer. When this function is turned on, the Pre-Collision Braking System OFF indicator light turns off.⇒ Refer to page 31.

Turning off Pre-Collision Throttle Management

NOTE• When Pre-Collision Throttle Management is turned off, the Pre-Collision

Braking System also turns off.• Even when Pre-Collision Throttle Management is turned off, if the ignition

switch is turned off and the engine is restarted, Pre-Collision ThrottleManagement will be turned on. The default setting for Pre-CollisionThrottle Management when the vehicle is restarted is “ON”.

S01120 S01121


68

Lane Departure WarningWhen vehicle speed is approximately 30 MPH (50 km/h) or more, this function warns thedriver if the system detects that the vehicle is likely to depart the traffic lane.When Lane Departure Warning activates, a buzzer sounds 6 short beeps, and the areaaround the lane indicator on the departing side flashes in yellow.

* The illustration depicts a vehicle departing the left lane.

WARNING

Lane Departure Warning will not operate in all conditions. It also will not auto-matically return the vehicle to the original lane. If the driver relies only on theLane Departure Warning to keep the vehicle in the lane, lane departure mayoccur, resulting in an accident.The Lane Departure Warning activates when it detects lane markings. How-ever, it is not a function which can detect the edge of a road (shoulders orside ditches, etc.) and warn the driver.

S01267

6

short beeps

S01126

LaneDeparture


Lane Departure Warning

69

CAUTIONIn the following situations, the Lane Departure Warning will or may not acti-vate:• Vehicle speed is approximately 30 MPH (50 km/h) or less.• When the steering wheel is turned significantly to either side• When the vehicle is driving around a curve whose radius is 0.18 miles (300

m) or smaller.• When the brake pedal is depressed or immediately after it is depressed• When the accelerator pedal is almost fully depressed and the vehicle is

accelerating or immediately after accelerating• When the following distance behind a vehicle in front is short• While the turn signal is operating and for approximately 4 seconds after the

turn signal lever has returned to its original position• For approximately 4 seconds after the hazard lamp has switched off• When the vehicle has not returned to the inside of the lane after the Lane

Departure Warning has activated• The lane is narrow.• When it is difficult for the camera to detect lane markings- There are no lane markings or they are very worn.- The lane markings are yellow.- It is difficult to detect lane markings as they are similar in color to the

road surface.- The lane markings are narrow.

NOTE• The following situations may cause incorrect lane detection and a faulty

Lane Departure Warning to occur.- Tire tracks on a wet road or snow-covered road- Boundaries between snow and asphalt, marks from road repair, etc.- Shadows of guardrails- Lane markings are drawn in double- There are some lane markings left from roadwork or markings from the

previous road.• When the Lane Departure Warning OFF indicator light is illuminated, the

Lane Departure Warning is inactive.⇒ Refer to page 70.


Lane Departure Warning

70

Press and hold the Lane Departure Warning OFF switch for approximately 2 seconds orlonger to turn off the Lane Departure Warning. When 1 short beep sound emits, this functionis turned off and the Lane Departure Warning OFF indicator light on the instrument panelwill illuminate.To turn the function back on, press and hold the Lane Departure Warning OFF switch againfor approximately 2 seconds or longer. When the function is turned on, the Lane DepartureWarning OFF indicator light turns off.

■ Lane Departure Warning OFF indicator lightThis indicator illuminates when the ignitionswitch is turned to the ON position, and thenapproximately 7 seconds after the enginestarts, it turns off or remains illuminateddepending on the current status (ON or OFF).It turns on when the Lane Departure Warningis turned off.It also illuminates under the following condi-tions.• When the EyeSight system has a malfunc-

tion⇒ Refer to page 86.

• When the EyeSight system has stopped temporarily⇒ Refer to page 87.

Turning off Lane Departure Warning

NOTE• When the Lane Departure Warning is turned off, the Lane Sway Warning is

also turned off.• The engine is turned off. The conditions prior to turning off the engine are

preserved and restored after starting the engine again.

S01122

S01123


Lane Sway Warning

71

Lane Sway WarningThis function detects wandering or drifting within a lane, and warns the driver. When LaneSway Warning activates, a buzzer sounds 6 short beeps and the left and right lane indica-tors flash alternately in yellow.This function activates only when the vehicle speed is approximately 38 MPH (60 km/h) ormore.

WARNING

Lane Sway Warning will not operate in all conditions. It also will not automati-cally correct wandering. If the driver relies only on the Lane Sway Warning toprevent the vehicle from wandering, an accident may occur.

CAUTIONUnder the following conditions, the Lane Sway Warning may not operate.• When driving on a winding road• When vehicle speed changes greatly• Immediately after a lane change• When it is difficult for the EyeSight stereo cameras to detect lane markings- There are no lane markings or they are the very worn.- It is difficult to detect lane markings as they are similar in color to the

road surface.- The lane markings are narrow.

S00650

6short beeps

S01127

Stay Alert


Lane Sway Warning

72

NOTE• Wandering detection is based on several minutes of driving data. Wander-

ing will not be detected immediately when it occurs. In addition, the warn-ing may continue for some time even after wandering stops.

• The Lane Sway Warning System is just a function that warns the driver.When the driver is tired, not concentrating on the road or not paying ade-quate attention to driving, be sure to take rest breaks as often as needed.

• When the Lane Departure Warning OFF indicator light is illuminated, theLane Sway Warning will not operate.



Lane Sway Warning

73

Press and hold the Lane Departure Warning OFF switch for approximately 2 seconds orlonger to turn off the Lane Sway Warning. When 1 short beep sound emits, this function isturned off and the Lane Departure Warning OFF indicator light on the instrument panel illu-minates.To turn the function back on, press and hold the Lane Departure Warning OFF switch againfor approximately 2 seconds or longer. When the function is turned on, the Lane DepartureWarning OFF indicator light turns off.⇒ Refer to page 70.

Turning off Lane Sway Warning

NOTE• When the Lane Sway Warning is turned off, the Lane Departure Warning is

also turned off. • The engine is turned off. The conditions prior to turning off the engine are

preserved and restored after starting the engine again.

S01122 S01123


74

Lead Vehicle Start AlertThis function notifies the driver by means of a buzzer and the lead vehicle indicator on themulti information display when the driver’s vehicle remains stopped after the vehicle in fronthas started to move forward. When the vehicle in front remains stopped continuously (withina following distance of approximately 32 ft (10 m) and the driver’s vehicle remains stoppedfor several seconds or longer), the system continues to detect the vehicle in front and thisalarm activates if the vehicle in front advances approximately 10 ft (3 m) or more while thedriver’s vehicle remains stationary.This function only activates when the select lever is in the , or position.When the Lead Vehicle Start Alert activates, a buzzer sounds a two-tone beep and the leadvehicle indicator moves.

NOTE• The Lead Vehicle Start Alert setting can be turned on or off.

⇒ Refer to page 89.• Under the following conditions, the Lead Vehicle Start Alert may activate

even when the vehicle in front has not started to move, or may not activateeven after the vehicle in front has started to move:

- A motorcycle or similar object has cut in between your vehicle and thestopped vehicle in front.

- Weather or road conditions prevent detection of the vehicle in front.- The EyeSight stereo cameras lose detection of the vehicle in front.

D M N

Two-tone beep

Lead vehicle

10 ft (3 m)or more

Leadvehicle

S01266 S01128

Vehicle Ahead Has Moved


Conventional Cruise Control

75


Conventional Cruise Control is a driving support system intended to allow more comfortabledriving on expressways, freeways and interstate highways. It can be used to travel at a con-stant speed by maintaining the vehicle speed that was set by the driver. Please rememberthat you should not exceed posted speed limits.

About Conventional Cruise Control

WARNING

• When Conventional Cruise Control is functioning, the system does not per-form tracking control to maintain following distance, as when using Adap-tive Cruise Control.Strive for safe driving and operate the brake pedal to decelerate the vehi-cle as necessary in order to ensure a safe following distance from the vehi-cle in front.

• Under the following conditions, do not use the Conventional CruiseControl. Doing so may result in an accident.

- Roads with heavy traffic or roads with sharp curvesYou may fail to drive at a speed that is appropriate for the road condi-tions, possibly resulting in an accident.

- Frozen roads, snow-covered roads or slippery road surfacesThe tires may spin, causing loss of control of the vehicle.

- Steep downhill gradesThe set vehicle speed may be exceeded.

- On a steep continuous downhill gradeThe brakes may overheat.

CAUTIONWhen using Cruise Control, be sure to check the EyeSight display area toconfirm which Cruise Control mode is selected: Adaptive Cruise Control orConventional Cruise Control.• If Adaptive Cruise Control is selected, “ ” (Adaptive Cruise Control

indicator) illuminates.• If Conventional Cruise Control is selected, “ ” (Conventional Cruise

Control indicator) illuminates.

NOTE• When the (CRUISE) switch is first turned on, the Adaptive Cruise

Control is set.• To change the Cruise Control mode, press and hold the / (fol-

lowing distance setting) switch for approximately 2 seconds or longer.(This is effective only when the main Cruise Control is on and neitherAdaptive Cruise Control nor Conventional Cruise Control are set.)

• Conventional Cruise Control can be used even when EyeSight is tempo-rarily turned off.



76

Conventional Cruise Control can be set when the following conditions are met.- The selector lever is in the position and the paddle shift is not operated.- The brake pedal is released.- The vehicle speed is between approximately 25 MPH (40 km/h) and 90 MPH (145

km/h).

■ Setting Conventional Cruise Control(1) Setting the Conventional Cruise Control to standby status.

Press the (CRUISE) switch. At this time, (Adaptive Cruise Control) and the“following distance setting” are displayed on the EyeSight display area of the multi infor-mation display. The set vehicle speed display will read “- - MPH”. When the (CRUISE) switch is pressed, the initial cruise control mode is alwaysAdaptive Cruise Control.

If the switch is pressed once more, the EyeSight display will turn off. It will also automaticallyturn off when the engine is stopped.

How to use the Conventional Cruise Control

D

S01985 S01110



77

(2) Switch to Conventional Cruise Control. Press and hold the / (following distance setting) switch for approximately 2seconds or longer to switch from Adaptive Cruise Control to Conventional CruiseControl. A buzzer sounds 1 short beep.At this time, the following distance setting indicator on the EyeSight display area of themulti information display turns off and (Conventional Cruise Control) is displayed.

To set the ready status:Conventional Cruise Control can be set whenall of the following conditions are met and

is displayed on the EyeSight displayarea.

- All doors (except the rear gate/trunk) areclosed.

- The driver’s seatbelt is fastened.- The electronic parking brake is not

engaged (The brake system warning lightis turned off.).

- The selector lever is in the position,and the paddle shift is not operated.

- The brake pedal is not depressed.- EyeSight operation is not temporarily stopped.⇒ Refer to page 87.- The road is not on a steep slope.- The steering wheel has not been turned significantly in either direction.- The X-mode is not turned on.- The vehicle speed is between approximately 25 MPH (40 km/h) and 90 MPH (145

km/h).(3) Control the accelerator pedal to reach the desired speed.

S01992 S01129

S02975D

本文.fm 77 ページ２０１５年５月２１日　木曜日　午後５時１０分


78

(4) When the vehicle speed is between approximately 25 MPH (40 km/h) and 90 MPH (145km/h), press the RES/SET switch to the “SET/-”.The vehicle speed at the time the switch is pressed becomes the set vehicle speed, andconstant-speed driving is engaged.

and the set vehicle speed are displayed on the EyeSight display area.

WARNING

The “brake more” warning will not activate while Conventional Cruise Controlis functioning.

CAUTIONDuring Conventional Cruise Control use, accelerator and brake control totrack the vehicle in front is not performed. Operate the accelerator and brakepedals as necessary.

NOTE• On a downhill grade, automatic braking may operate in order to maintain

the set vehicle speed.• When driving on a curve, the vehicle may not accelerate, or may deceler-

ate, even if the set speed is higher than the current vehicle speed.• To return to Adaptive Cruise Control use, cancel the Conventional Cruise

Control and then briefly press the / (following distance setting)switch.

S01986 S01130

本文.fm 78 ページ２０１５年５月２１日　木曜日　午後５時１０分


79

■ Increasing the set vehicle speedThe following two methods can be used to increase the set vehicle speed.

●Using the RES/SET switchPush the RES/SET switch in the following way while you are driving with ConventionalCruise Control on:• Push the RES/+ switch towards the position (1) briefly: the set vehicle speed will increase

in increments of 1 MPH (1 km/h) every time the button is pushed.• Push the RES/+ switch towards the position (1) for longer: the set vehicle speed will

increase in increments of 1 MPH (1 km/h) while the button is being pushed.• Push the RES/+ switch towards the position (2) briefly: the set vehicle speed will increase

to the next 5 MPH (5 km/h) increment every time the button is pushed.• Push the RES/+ switch towards the position (2) for longer: the set vehicle speed will

increase to the next 5 MPH (5 km/h) increment while the button is being pushed and willcontinue to advance target speed in 5 MPH (5 km/h) increments as long as the button ispushed.

The set vehicle speed is shown on the EyeSight display area.

●Using the accelerator pedalOperate the accelerator pedal to increase thevehicle speed.When the desired speed is reached, press theRES/SET switch to the “SET/-”. When theswitch is released, the new vehicle speed isset.

S01990

S01986



80

■ Decreasing the set vehicle speed●Using the RES/SET switch

Push the RES/SET switch in the following way while you are driving with ConventionalCruise Control on:• Push the SET/- switch towards the position (1) briefly: the set vehicle speed will decrease

in increments of 1 MPH (1 km/h) every time the button is pushed.• Push the SET/- switch towards the position (1) for longer: the set vehicle speed will

decrease in increments of 1 MPH (1 km/h) while the button is being pushed.• Push the SET/- switch towards the position (2) briefly: the set vehicle speed will decrease

to the next 5 MPH (5 km/h) decrement every time the button is pushed.• Push the SET/- switch towards the position (2) for longer: the set vehicle speed will

decrease to the next 5 MPH (5 km/h) decrement while the button is being pushed and willcontinue to lower target speed in 5 MPH (5 km/h) decrements as long as the button ispushed.

The set vehicle speed is shown on the EyeSight display area.

●Using the brake pedal(1) Depress the brake pedal to decrease the vehicle speed. (Conventional Cruise Control

will be canceled and will be turned off.)(2) When the desired speed is reached, press the RES/SET switch to the “SET/-”. The

speed at the time of pressing the switch will be set as the new vehicle speed, and itappears in the EyeSight display area.

■ Accelerating temporarilyDepress the accelerator pedal to accelerate temporarily.When the accelerator pedal is released, the vehicle returns to the set vehicle speed.

S01991



81

■ Decelerating temporarily

Depress the brake pedal to decelerate tempo-rarily. When the brake pedal is depressed,Conventional Cruise Control will be canceled.While the set vehicle target speed remainsdisplayed on the EyeSight display area, will be turned off.Release the brake pedal and press theRES/SET switch for “RES/+” to reset the setvehicle target speed.

■ Canceling Conventional Cruise Control●Manual Cancellation by the driver

Any of the following operations will cancel Conventional Cruise Control.• Depress the brake pedal.

will be turned off while the set vehicle target speed remains displayed on theEyeSight display area.

• Press the (CRUISE) switch. will be turned off while the set vehicle target speed remains displayed on the

EyeSight display area.When the (CRUISE) switch is pressed again, the will be turned off andConventional Cruise Control will be turned off.

S01131

will be turned off.

S01985 S01131

will be turned off.



82

●Automatic cancellation by the systemIn the following cases, a buzzer sounds a single long beep and the Cruise control function isautomatically canceled ( is displayed on the EyeSight display area.). After the condi-tions listed below have been eliminated, perform the cruise control set operation again toreactivate cruise control.• The select lever was moved to a position other than .

The cruise control function can be used again after the lever is returned to the posi-tion.

• A paddle shift switch was operated duringdriving with the lever in the position.The cruise control function can be usedagain after the shift indicator returns to .

• Vehicle speed drops to approximately 20MPH (30 km/h) or less (due to a steep uphillgrade or some other reason).

• The X-mode is turned on (the X-mode indicator light illuminates).- Cruise control can be resumed after the X-mode is turned off.

• Vehicle speed rises to approximately 100 MPH (160 km/h) or more.• The ABS, Vehicle Dynamics Control or Traction Control functions activate.• Any door (except the rear gate/trunk) was opened.• The driver’s seatbelt is unfastened.• The Electronic Parking Brake is engaged (When the brake system warning light is illumi-

nated or flashing).• When the EyeSight system has a malfunction. (“ ” (EyeSight Warning indicator:

Yellow) is turned on.)• The steering wheel is turned significantly in either direction.• The grade of the road is steep.• The Pre-Collision secondary braking has activated.

WARNING

Do not use Conventional Cruise Control on slippery roads. Doing so mayresult in an accident.

DD

S01132

D

D



83

CAUTIONWhen shifting the selector lever to the position, Adaptive Cruise Controlwill be automatically canceled. Do not shift the lever to the position unlessit is an emergency. Otherwise the engine brake may not operate, which couldcause an accident.

NOTE• If EyeSight is malfunctioning, the EyeSight warning indicator is displayed

on the multi information display and the Pre-Collision Braking System OFFindicator light and Lane Departure Warning OFF indicator light illuminate. Ifthis occurs, stop the vehicle in a safe location and then stop the engineand restart it. If the indicators remain illuminated after restarting theengine, Conventional Cruise Control cannot be used. This will not interferewith ordinary driving; however the system should be inspected by aSUBARU dealer as soon as possible.

⇒ Refer to page 86.• When operation of Conventional Cruise Control has been automatically

canceled, perform the set operation again after the condition that causedthe cancellation has been eliminated. If cruise control cannot be set evenafter the condition has been corrected, EyeSight may be malfunctioning.This will not interfere with ordinary driving; however the system should beinspected by a SUBARU dealer as soon as possible.

NN



84

■ Resuming a vehicle speed that was previously storedA vehicle speed that has been previously set is stored in memory*. To recall and set thatvehicle speed, press the RES/SET switch to the “RES/+”. (The EyeSight display area showsthe set condition again.)Resume is possible when a vehicle speed was previously set, and the current vehicle speedis approximately 20 MPH (30 km/h) or more.

NOTE* The vehicle speed stored in memory is erased at the following times:

- The cruise control is turned off by pressing the (CRUISE) switch.- Either vehicle Dynamics Control or Traction Control Function has been

activated.- The cruise control mode was switched from Conventional Cruise Control

to Adaptive Cruise Control.• The vehicle will drive at a constant speed that was set between approxi-

mately 25 MPH (40 km/h) and 90 MPH (145 km/h).• If there is no vehicle speed in the memory (a previously set vehicle speed),

the vehicle speed cannot be resumed by depressing the RES/+ switch.

S01993 S01130


List of buzzer sounds

85

List of buzzer sounds

*The buzzer that indicates when a lead vehicle is detected or when it is no longer detected (LeadVehicle Acquisition Sound), as well as the Lead Vehicle Start Alert can be turned on or off.⇒ Refer to page 89.

Buzzer sound Status Reference page

Single continuous beep

Pre-Collision Braking System:Secondary Braking is active. ⇒ Refer to page 27.

Single long beep

Adaptive Cruise Control or Conventional CruiseControl is canceled.

⇒ Refer to pages 49 and 82.

The Electronic Parking Brake was automaticallyapplied during stay-stopped condition byAdaptive Cruise Control.

Lane Keep Assist is canceled automatically.

Repeated short beeps

Pre-Collision Braking System:First Braking is active.

⇒ Refer to page 27.Pre-Collision Braking System:The following distance warning is active.The “brake more” warning from Adaptive CruiseControl is active. ⇒ Refer to page 52.

Pre-Collision Throttle Management is active. ⇒ Refer to page 62.

6 short beepsThe Lane Departure Warning is active. ⇒ Refer to page 68.

The Lane Sway Warning is active. ⇒ Refer to page 71.

5 intermittent beeps and 1 long

beep

The stay-stopped function of Adaptive CruiseControl continued for 2 minutes and the Elec-tronic Parking Brake is automatically applied.


1 short beep

Either of the following occurred while AdaptiveCruise Control was set.- A vehicle in front is detected*.- A vehicle in front is no longer detected*.


The cruise control mode (Adaptive CruiseControl Conventional Cruise Control) ischanged.


EyeSight is malfunctioning.⇒ Refer to pages

86 and 87.EyeSight operation is temporarily stopped.

Pre-Collision Braking System and Pre-CollisionThrottle Management are turned on/off.


The Lane Departure Warning and the LaneSway Warning are turned on/off.


Two-tone beep Lead Vehicle Start Alert is active*. ⇒ Refer to page 74.


86

EyeSight malfunction and temporary stopIf a malfunction is detected in the EyeSight system, the indicators in the instrument paneland the multi information display inform the driver of the malfunction. Check the displayedcontents and take the appropriate action.

■ Malfunction (including position/angle misalignment of stereocameras)

The buzzer sounds 1 short beep and theEyeSight warning indicator (yellow)flashes or illuminates. At the same time, thePre-Collision Braking System OFF indicatorlight and the Lane Departure Warning OFFindicator light will illuminate. A message willalso be displayed on the multi informationdisplay.

Displayed screen Cause Action

An EyeSight malfunction orposition/angle misalign-ment of stereo cameras hasoccurred.

Inspection and adjustment is necessary.Contact your SUBARU dealer.

CAUTIONIf both the EyeSight warning indicator and the CHECK ENGINE warninglight/malfunction indicator light illuminate at the same time while driving, haveyour vehicle checked/repaired by a SUBARU dealer as soon as possible.EyeSight cannot be used if there is an abnormality with the engine, etc.

NOTE• If the EyeSight warning indicator illuminated or flashed, stop the vehicle in

a safe location, and after stopping the engine once by turning off theengine, restart the engine.

• If the indicator continues illuminating or flashing even after the engine hasbeen restarted, the EyeSight system has a malfunction. In this case, allEyeSight functions will be stopped. Normal driving will still be possible.However, contact a SUBARU dealer for an inspection.

S01134

S00699


EyeSight malfunction and temporary stop

87

■ Temporary stopThe buzzer will sound one short beep, and theEyeSight temporary stop indicator (white), Pre-Collision Braking System OFFindicator light and Lane Departure WarningOFF indicator light will illuminate at the sametime.A message will also be displayed on the multiinformation display.When the cause has been eliminated, tempo-rary stop will be canceled and the EyeSightsystem will automatically restart.


It is difficult for the stereocameras to detect objects infront• The front windshield is

dirty or fogged up• Poor weather conditions• Strong light from the front

• Clean the front windshield.• In bad weather or if there is

strong light from the front, the EyeSight system will restart once you have driven your vehicle for a period of time and the con-ditions affecting the system have improved.If the system does not restart, even after the con-ditions have improved and a period of time has elapsed, contact your SUBARU dealer for an inspection.

In low or high temperatures The system will restart once the temperature is within the operational range of the EyeSight system.If the system does not restart, even when the tem-perature inside the vehicle is normal, contact your SUBARU dealer for an inspection.

S01135

S00700

S00701


EyeSight malfunction and temporary stop

88


• When the EyeSight sys-tem is starting

• When the system has determined that the vehi-cle is extremely inclined

• When the pre-collision secondary braking has operated 3 times after the engine was started

• When the engine is stopped

• When the electronic power steering system is in the overheating preven-tion status because the steering wheel has been operated while the vehicle is at a standstill or driving at an extremely slow speed

• When the EyeSight sys-tem judged a different value due to the removal or installation of the steer-ing wheel

• When wheel alignments are deviated

The system will restart once the cause has been elimi-nated. At this time, it may take some time for the sys-tem to restart.If the system does not restart, even after the condi-tions have improved and a period of time has elapsed, contact your SUBARU dealer for an inspection.

NOTEWhen the EyeSight temporary stop indicator has illuminated, no EyeSightfunctions can be used except for Conventional Cruise Control.

S00694


Customizing functions

89

Customizing functionsThe following settings can be changed on the multi information display.

■ How to customizeOperations can be performed when the selec-tor lever is in the position and the ignitionswitch is in the ON position while the vehicleis parked.(1) Pull the / switch toward you to dis-

play the “Change settings” screen.Keep pulling the (Info)/SET switch tochange to the settings screen.

(2) Pull the / switch toward you,select “EyeSight”, and pull the (Info)/SET switch to confirm.The system will then switch to theEyeSight settings screen.

Operate the following switches according towhat is displayed on the screen.• Select: (Return) switch/

(Send) switch• Confirm: (Info)/SET switch

Item Setting Default setting

EyeSight

Warning Volume Max/Mid/Min Mid

Lead Vehicle Acquisition Sound ON/OFF ON

Lead Vehicle Moving Monitor Function ON/OFF ON

Vehicle Icon ON/OFF ON

NOTEThe following settings can be restored to the factory (default) settings.⇒ Refer to the Owner’s Manual for your vehicle.

SETEnter

1/7Select

Select

SET

S01136

Change settings Settings screen

Pull and holdi/SET Switch For Menu

Settings

Screen Settings

P


Customizing functions

90

●Warning Volume settingThe volume can be set to Max/Mid/Min.When on the Warning Volume settings screen, if the volume is selected with the /switch, 3 short beeps will sound.

●Lead Vehicle Acquisition Sound settingThe Lead Vehicle Acquisition Sound setting can be activated (ON) or deactivated (OFF).

●Lead Vehicle Moving Monitor FunctionThe Lead Vehicle Start Alert function setting can be activated (ON) or deactivated (OFF).

●Vehicle Icon settingYour vehicle indicator setting can be activated (ON) or deactivated (OFF).

●Cancelling the custom functionsIn the following cases, the custom functions will be canceled and the “Change settings”screen will be displayed.• When you keep pulling the (Info)/SET switch toward you• When the engine is turned off• When the switch is not operated for approximately 30 seconds

NOTEWhen “Return” is selected, the system will return to the screen directly abovethe current one.


Message screen list

91

Message screen listIf an EyeSight warning or malfunction is detected, a message will be displayed on the multiinformation display. Depending on the message, a buzzer will sound at the same time.

If a message is displayed, refer to the mes-sage list and take the appropriate action.While the mark is illuminated, pull the (Info)/SET switch to indicate the messageagain.

■ Message screen list (precautions and notices)

Item Displayed screen mark Action

Pre-Collision Braking System None ⇒ Refer to page 27.

The “brake more” warning None ⇒ Refer to page 52.

Pre-Collision Throttle Management None ⇒ Refer to page 62.

Apply Brake None ⇒ Refer to page 27.

Lane Departure Warning None ⇒ Refer to page 68.

Normal indicator Normal indicatorMessage indicator

S01137

EyeSight Off Check Manual

mark

S01138

S00695

S01139

Apply Brake To Hold

Position Check Manual

S00696


Message screen list

92

■ Message screen list (malfunction, temporary stop)

Steering operation not detected by Lane Keep Assist

None ⇒ Refer to page 54.

Lane Sway Warning None ⇒ Refer to page 71.

Lead Vehicle Start Alert None ⇒ Refer to page 74.

Adaptive Cruise Control/Conventional Cruise Control automatic cancellation (when the grade of the road is very steep)

None ⇒ Refer to pages 49 and 82.


EyeSight System Malfunction

Yes (yellow) ⇒ Refer to page 86.

EyeSight system temporary stop

Yes (white) ⇒ Refer to page 87.




Keep Hands OnSteering Wheel

S01997

S00697

S00698

S01139

Cruise Control Cancelled Steep Hill

Check Manual

S00699

S00700

S00701

S00694

本文.fm 92 ページ２０１５年５月２１日　木曜日　午前８時４２分

Troubleshooting

93

Troubleshooting

Adaptive Cruise control cannot be set.

Did you remember to press the (CRUISE) switch?If you have not pressed the (CRUISE) switch, (Adaptive Cruise Control) will not be shown.

Is EyeSight operation temporarily stopped?When EyeSight is temporarily stopped, is displayed on the multi information display.Set cruise control again after the reason for the temporary stop has been cor-rected.

Is displayed?Cruise control cannot be set when is not displayed. Set cruise control when

is displayed.

is not displayed.

Are the requirements for setting cruise control met?In any of the following cases, will not be displayed.

• The brake pedal is depressed.• The vehicle speed is not between approximately 0 MPH (0 km/h) and 90

MPH (145 km/h) (when Adaptive Cruise Control is operating).• The vehicle speed is not between approximately 25 MPH (40 km/h) and 90

MPH (145 km/h) (when Conventional Cruise Control is operating).• The combination meter indicates a position other than . (The select

lever or paddle shift switches are manually operated.)• The driver’s seatbelt is unfastened.• Any door is opened (except the rear gate/trunk).• The electronic parking brake is applied (The brake system warning light is

illuminated or flashing.)*.• The vehicle is on a steep grade.• The X-mode is turned on. (The X-mode indicator illuminates.)• The steering wheel is turned significantly in either direction.

*For details of how to release the Electronic Parking Brake, refer to theOwner’s Manual for your vehicle.

D


Troubleshooting

94

A vehicle (in front of your vehicle) is not detected, is detected later or detection is lost quickly.

Is the vehicle in front stopped, moving slowly relative to your vehicle or moving extremely slowly?Detection of stopped vehicles, vehicle moving slowly relative to your vehicle, and vehicles moving extremely slowly may be difficult.

Is the windshield dirty or fogged?If the windshield is dirty or fogged, it may not be possible to detect object or vehi-cles. Clean off the dirt or fog from the windshield, and then try using the system again.

Is the vehicle in front far away?The maximum detection distance of EyeSight’s stereo cameras is approximately 360 ft (110 m). Detection is not possible if the vehicle is farther away.

Is the vehicle on a curve?The detection range is limited in the left and right directions when the cameras are properly aimed.

Is the vehicle on a road with repeated uphill and downhill grades (such as an over-pass), or on a banked road?The detection range is limited in the up and down directions.

Did the vehicle detected in front change?Detection may be delayed after the vehicle in front has changed.

Have water, snow or other substances been kicked up by the vehicle in front as it drives?When water or snow have been kicked up, it may not be possible to detect the vehicle in front.

Control is activated even though no vehicle in front is detected?

Is there a vehicle in the neighboring lane?Depending on the road conditions, vehicles in neighboring lanes may be detected as well as a vehicle directly in front.

Are you driving on or near a curve?When driving on a curve, braking control may be activated in response to guard rails, the angle of the steering wheel, or roadside structures.

The Lead Vehicle Start Alert activates, even though there is no vehicle in front.

Depending on surrounding objects, traffic environment and weather, the Lead Vehicle Start Alert may issue a warning in response to objects other than a vehicle that appear in front of your vehicle.


Troubleshooting

95

EyeSight does not restart after a temporary stop.

Is the X-mode turned on?EyeSight cannot be activated when the X-mode is turned on.

Are you driving in the rain with old wipers or is there an oily film on the windshield?Replace the wipers with new ones, or clean the oily film off the windshield.Are you driving in poor weather conditions with heavy rain, snow, fog, or dust? In these cases, EyeSight may temporarily stop operating while visibility is very low.

Is your vehicle subject to sunlight from the front (sunset or sunrise, etc.) or to bright headlights from oncoming vehicles at nighttime?In these cases, EyeSight may temporarily stop operating.

Has the vehicle been parked in a cold or hot place? In either of these cases, EyeSight may temporarily stop operating until the temperature increases or decreases to a temperature at which the camera is operable.

The timing of the “brake more” warning is sometimes earlier and sometimes later than what seems to be normal operation.

The “brake more” warning sounds when the system determines that more braking is necessary, based on conditions such as the distance from the vehicle in front and the difference in speed compared to it. As a result, timing may vary depend-ing on how the brakes are applied in relation to the vehicle in front, and your rela-tive speed to that vehicle.

When the vehicle in front has turned off the road away or the distance from the vehicle in front has increased, acceleration is sometimes slower or faster.

Depending on the timing of when the detection of the vehicle in front is lost, EyeSight’s ability to react may be slower, causing the start of acceleration to feel delayed and braking time to feel longer than what seems to be normal operation.


Troubleshooting

96

Cruise control is canceled automatically.

Did you perform one of the following operations?• Manually depressing the brake pedal• Pressing the (CRUISE) switch- If the (CRUISE) switch is pressed while the cruise control is set,

the cruise control will be canceled.• Staying on a steep slope• Turning the steering wheel sharply• Operating the paddle shift lever• Shifting the selector lever to the position• Pressing the X-mode switch (The X-mode indicator illuminates.)

Has the EyeSight system temporarily stopped?

A noise occurs when automatic braking control activates.

This is the sound of the automatic braking control operating - there are some mechanical components to the system, and they do occasionally make audible sounds during automatic braking control. It is not necessarily a malfunction.

Braking control activates frequently when driving in heavy traffic.

Unlike a human driving, the EyeSight system performs control based only on the actions of vehicles or objects in front. As a result, acceleration and deceleration may be more frequent while the system adjusts to vehicles or objects the camera system is detecting. If it is difficult to maintain a consistent following distance under certain conditions (like in bad weather or urban environments, etc.), do not use Adaptive Cruise Control.

The Electronic Parking Brake is applied automatically while the stay-stopped func-tion is operating.

The electronic parking brake will be applied in the following cases.• The stay-stopped function is continuously applied for approximately 2 min-

utes.• Automatic cancel conditions (⇒ refer to page 49.) have been met.

M


Troubleshooting

97

Lane Keep Assist was unexpectedly canceled

Did you take your hands off the steering wheel? Did you just lightly put your hands on the steering wheel while driving?If the system cannot detect the steering operation of the driver, it will temporarily cancel Lane Keep Assist.

Did you turn a tight corner?Lane Keep Assist does not operate while turning a tight corner.

Did you perform one of the following operations?• Operating the turn signal lever• Operating the steering wheel to depart from a lane• Depressing the accelerator pedal deeply• Operating the windshield wiper in a high speed• Driving your vehicle at a speed less than approximately 37 MPH (60 km/h)

or more than approximately 93 MPH (150 km/h)• Depressing the brake pedal• Turning on the hazard warning flasher switch


98

MEMO


Documents

Foreword...*2: For details about the combination meter, refer to the Owner’s Manual for your vehicle. B2522BE-A.book 3 ページ 2015年5月15日 金曜日 午後12時22分

Foreword...*2: For details about the combination meter, refer to the Owner’s Manual for your vehicle. B2522BE-A.book 3 ページ 2015年5月15日金曜日午後12時22分