1. Unpack box. Expand the main bike frame. Remove all parts and pieces from packaging. Expand the main bike frame. If there is too much resistance, you may move on to Step 2 and the bicycle will start to open itself.
Marketing-08
Typewriter
2. Install the Front and Rear Stabilizers. Loosen screws in the front stabilizer (with wheels facing forward), and insert into grooves on front section of bike frame. Rotate rubber leveling feet to make holes line up. Tighten screws. Repeat with rear stabilizer.
Marketing-08
Typewriter
3. Install the Left and Right Pedals. Attach the left pedal onto left side of bike. Thread counter-clockwise. See stickers on pedal for reference. Tighten with wrench. Attach the right pedal onto right side of bike. Thread clockwise. Tighten with wrench.
Marketing-08
Typewriter
HARDWARE LIST
Marketing-08
Rectangle
Marketing-08
Typewriter
4. Install the Handlebar and Control Panel. Place the front handlebar on the corresponding grooves in the frame, tighten with bolts and washers. Connect the speed sensor wire from the frame (male) to the control panel (female). Connect the handlebar heart rate wires (female) to the control panel (male). Order does not matter. Place the control panel on handlebar plate and tighten screws.
Marketing-08
Typewriter
5. Install the Back Handlebar and Seat Cushion Install the back handlebar to the backrest. Install the seat cushion to the seat post. Connect the two assemblies together using the two longer bolts found on the seat post.
Marketing-08
Typewriter
6. Install Combined Seat Post / Backrest to frame. Place the complete seat post and backrest assembly onto the main frame. Attach the seat height adjustment knob (triangular knob) and tighten. 7. Attach recline adjustment angle knob. Recline adjustment holes are located on the back of the bike frame, below the seat post / backrest assembly.
CONTROL PANELBATTERY INSTALLATION
Marketing-08
Typewriter
Requires 2 AA batteries (included). Do not mix old and new batteries. Do not mix alkaline, standard (carbon-zinc), or rechargeable (NiCd, Ni-Mh, etc) batteries.
Marketing-08
Typewriter
1. Open battery compartment door on the back the control panel.
Marketing-08
Typewriter
2. Install 2 AA batteries (included) according to the correct polarity.
Marketing-08
Typewriter
2. Note the diagram inside the compartment that shows the correct battery installation polarity.
Marketing-08
Typewriter
4. Replace the battery compartment door.
DISPLAY:
TIME, DIST, CAL, and PULSE: Default to previous setting until reset (RESET) or programmed with new setting (SET).
SCAN: Cycles through all functions below. Press MODE to make selection.
TIME: Press RESET to keep track of total time or SET to program a countdown timer. When countdown reaches 0, alarm will sound. Press any button to silence.
SPEED: Estimated MPH.
DIST: Press RESET to keep track of total distance in miles or SET to program a countdown from distance goal. When countdown reaches 0, alarm will sound. Press any button to silence.
ODO: Total exercise miles.
CAL: Press RESET to keep track of total estimated calories expended or SET to program a countdown from calorie goal. When countdown reaches 0, alarm will sound. Press any button to silence.
PULSE: User must hold the heart rate monitor grips on the handle bars for heart
rate to display. Press RESET to keep track of heart rate or SET to program a target heart rate. Whenever target heart rate is surpassed, alarm will sound. To silence, remove hands from heart rate monitor grips or press RESET.
CONTROL PANEL
SCAN
TIME
SPEED
DIST
ODO
CAL
PULSE
RESET MODE SET
BUTTONS:
RESET: Clears data from selection (TIME, DIST,CAL, or PULSE). Press for3 seconds to reset all stored information from previous workout except for total exercise miles (ODO).
MODE: Selects mode (SCAN, TIME, SPEED, DIST, ODO, CAL, or PULSE). Press for3 seconds to reset all stored information from previous workout except for total exercise miles (ODO).
SET: Press to program new setting for selected mode (TIME, DIST, CAL, or PULSE). To increase setting faster,press for 3 seconds. Press again to program.
