Floor Feeder Repair Parts Manual - Chore-TimeFloor Feeder Repair Parts Manual Volume II 3 Purpose of the Repair Parts Manual The purpose of the Repair Parts Manuals is to provide the

Floor Feeder

Repair Parts ManualVolume II

(March 1990 to September 1996)

MF1300A96December 1996

Warranty Information

Chore-Time Equipment warrants each new product manufactured by it to be free from defects in material orworkmanship for one year from the date of initial installation by the original purchaser. If such a defect is foundby Chore-Time to exist within the one year period, Chore-Time will, at its option, (a)repair or replace suchproduct free of charge, F.O.B. the factory of manufacture, or (b) refund to the original purchaser the originalpurchase price, in lieu of such repair or replacement.

Additional extended warranties are herewith provided to the original purchaser as follows:

1. TURBO™ and RLX™ Fans, less motors, for three years from date of installation.*2. Poultry feeder pans that become unusable within five years from date of installation.

Warranty prorated after three years usage.3. MEAL-TIME Hog Feeder pans that become unusable within five years of installation.4. Rotating centerless augers, excluding applications involving High Moisture Corn

(exceeding 18%), for ten years from date of installation. Note: MULTIFLO andapplications involving High Moisture Corn are subject to a one year warranty.

5. Chore-Time manufactured roll-formed steel auger tubes for ten years from date ofinstallation.

*6. Laying cages that become unusable within ten years. Warranty prorated after three yearsusage.

*7. ULTRAFLO Auger and ULTRAFLO Feed Trough (except ULTRAFLO TroughLiners) are warranted for a period of five (5) years from date of original purchase againstrepeated breakage of the auger or wear-through of the feed trough caused solely by theauger.

Conditions and limitations:

1. The product must be installed and operated in accordance with instructions published byChore-Time or warranty will be void.

2. Warranty is void if all components of a system are not supplied by Chore-Time.3. This product must be purchased from and installed by an authorized Chore-Time dealer or

certified representative thereof, or the warranty will be void.4. Malfunctions or failure resulting from misuse, abuse, negligence, alteration, accident, or

lack of proper maintenance shall not be considered defects under this warranty.5. This warranty applies only to systems for the care of poultry and livestock. Other

applications in industry or commerce are not covered by this warranty.

Chore-Time shall not be liable for any consequential or special damage which any purchaser may suffer or claimto have suffered as a result of any defect in the product. "Consequential" or "special damages" as used hereininclude, but are not limited to, lost or damaged products or goods, costs of transportation, lost sales, lost orders,lost income, increased overhead, labor and incidental costs and operational inefficiencies.

THIS WARRANTY CONSTITUTES CHORE-TIME’S ENTIRE AND SOLE WARRANTY AND CHORE-TIMEEXPRESSLY DISCLAIMS ANY AND ALL OTHER WARRANTIES, INCLUDING, BUT NOT LIMITED TO,EXPRESS AND IMPLIED WARRANTIES AS TO MERCHANTABILITY, FITNESS FOR PARTICULARPURPOSE SOLD AND DESCRIPTION OR QUALITY OF THE PRODUCT FURNISHED HEREUNDER.

Any exceptions to this warranty must be authorized in writing by an officer of the company. Chore-Time reservesthe right to change models and specifications at any time without notice or obligation to improve previous models.

*See separate Chore-Time Cage Wire Warranty as to these products.

CHORE-TIME EQUIPMENT, A Division of CTB, Inc.P.O. Box 2000, Milford, Indiana 46542-2000 U.S.A.

Floor Feeder Repair Par ts Manual Volume I I 3

Purpose of the Repair Parts Manual

The purpose of the Repair Parts Manuals is to provide the CHORE-TIME Distributors & Dealers alisting of current and discontinued parts for their reference in identifying and/or ordering parts.

Note:The Floor Feeder Repair Parts Manual has been divided into two separate volumes; VolumeI & Volume II.

Volume I includes Floor Feeder products up to March 1990.

Volume II includes Floor Feeder products that have been current anytime from March 1990to present.

Products that were current before and after March 1990 appear in both volumes.

Additional copies of this book may be ordered through the CHORE-TIME Customer ServiceDepartment. Refer to this manual by name, volume, and part number (MF1300) when ordering.

When ordering parts from this manual, please note the following:

1. Parts numbers that have a line through them (i.e. 3185) have been discontinued and areno longer available.

2. All parts should be ordered by part number and description as listed in the parts list.

3. All parts are billed when shipped. If a returned part is defective and within warranty,credit will be allowed against billing.

4. Check shipment for damages and shortages. All claims for damages or shortagesresulting from shipping must be filed with the carrier.


Table of Contents Control Units

Model C & CT Control Unit - Part No: 1878-8 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6Model 2000 Control Unit - Part No: 1878-9 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6Model C & CT Control Unit - Part No: 1878-8 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8Model C End Control Unit - Part No: 24396 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9Model C End Control Unit - Part No: 24396 (1-Phase), 27757 (3-Phase) . . . . . . . . . . . . . . . . . . . . . . . . . 10Model C2 End Control Unit - Part No: 28116 (1-Phase), 28270 (3-Phase) . . . . . . . . . . . . . . . . . . . . . . . . 11Model H2 End Control Unit - Part No: 24397 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12Model H2 End Control Unit Part No: 24397 (1-Phase), 27762 (3-Phase) . . . . . . . . . . . . . . . . . . . . . . . . . 13Model 2000 End Control Unit - Part No: 24395-0 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14Model G End Control Unit - Part No: 29511 (1-Phase), 29521 (3-Phase) . . . . . . . . . . . . . . . . . . . . . . . . 15Adult Turkey Feeder Control Unit - Part No: 6035 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16Adult Turkey Feeder Control Unit - Part No: 6035 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17Adult Turkey Feeder Control Unit - Part No: 6035 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18Adult Turkey Feeder Drop Tube Assembly. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19Model C, CT, H, & 2000 Intermediate Control Unit - Part No: 5302-0 . . . . . . . . . . . . . . . . . . . . . . . . . . . 20Model C & CT Intermediate Control Unit - Part No: 24190 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21Model C Intermediate Control Unit - Part No: 24190 (1-Phase), 27758 (3-Phase) . . . . . . . . . . . . . . . . . . 22Model C2 Intermediate Control Unit - Part No: 28117 (1-Phase), 28275 (3-Phase). . . . . . . . . . . . . . . . . . 23Model 2000 Intermediate Control Unit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24Part No: 24191-1 (shallow pan), 24191-2 (deep pan) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24Model G Intermediate Control Unit - Part No: 29512 (1-Phase), 29522 (3-Phase) . . . . . . . . . . . . . . . . . . 25Model H2 Intermediate Control Unit - Part No: 25435 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26Model H2 Intermediate Control Unit - Part No: 25435 (1-Phase), 27760 (3-Phase) . . . . . . . . . . . . . . . . . 27Adult Turkey Feeder Intermediate Control Unit - Part No: 6039. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28

Power UnitsFloor Feeder Power Units . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29Floor Feeder Power Unit Miscellaneous Components . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30

Boot ComponentsSingle Boot Components - Part No: 6822 (Broiler), 6821 (ATF) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32Twin Boot Components - Part No: 6824 (Broiler), 8460 (ATF) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33ULTRAPAN® Boot Assembly - Part No: 34824 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34ULTRAPAN® Intake Cup Assembly - Part No: 28119 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35ULTRAFLO® Intake Cup Assembly - Part No: 25167 (domestic) & 27380 (Intn’l only) . . . . . . . . . . . . . . . . . . . . 36

Feed Hoppers100# Feeder Line Hopper . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37200# Feeder Line Hopper - Part No: 9474 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38200# Feeder Line Hopper - Part No: 7941 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39300# Feeder Line Hopper . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40300# Breeder Feeder Hopper . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41400# Feeder Line Hopper - (Part No. 27530) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42Lower Hopper Switch - (Part No. 8798) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43

Feeder Line ComponentsBroiler, Cockerel, & ATF Feeder Line Components - (Model C, C2 H, H2, G, 2000) . . . . . . . . . . . . . . . . 44ULTRAPAN® Feeder Line Components . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45ULTRAFLO® Feeder Line Components . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46ULTRAFLO® Feeder Line Grill Options . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47

Feeder AssembliesModel C . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48Model C2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49Model H . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50Model H2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51Model G . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 52Model 2000 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 53Adult Turkey Feeder . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 54


Suspension ComponentsMiscellaneous Components . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 55Power Winch: Part No. 2883 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 56Electric Power Lift: Part No. 14580 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 57Electric Power Lift: Part No. 14580 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 58Switch Box (for Electric Power Lift): Part No. 14316 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 59

Electrical Controls and Components Breeder Control Panel: Part No. 34380 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 61Breeder Control Panel: Part No. 25175 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 62Breeder Feeder Feed-Only Control Panel: Part No. 27440 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 63Meal-Time Control Panel: Part No. 34385 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 64Time Clock Control: Part No. 34574 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 65Breeder Feeder Control: Part No. 8700A . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 66Meal-Time Control Panel: Part No. 7022A . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 67Time Clock Control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 68Time Clock Control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 69Tork Time Clocks . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 70Contactor Control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 71Contactor Control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 71Hopper Level Control: Part No. 2912 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 72Hopper Level Control: Part No. 14550 & 27761 (International) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 73

Floor Feeder Scale Systems and ComponentsWeigh Scale Template: Part No. 5798 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 74Weigh Scale Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 75Beam Box Assembly: Part No. 5790 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 765000# Weigh Beam Assembly: Part No. 9447* . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 778000# Weigh Beam Assembly: Part No. 6514* . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 77Model 100 & Model 200 Digital Indicators . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 78Connection Box: Part No. 30226 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 78J-Boxes & Cable Sets . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 79J-Box Duplex Kit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 79Duplex J-Box . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 80Miscellaneous Components and Cable Sets . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 80Junction Control: Part No. 25784 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 81Junction Control w/Fill Option: Part No. 30240 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 82Load Cells and Mount Kits . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 83Load Cells and Mount Kits . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 84Power Supply . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 84Livestock Scale Indicators . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 85Livestock Scale Load Cells . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 85Hopper Scales: Part No. 24176 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 86Hopper Scales Switch Assembly: Part No. 33653 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 87Hopper Scales Switch Box Assembly: Part No. 14613 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 87

Floor Feeder Screener ComponentsWEIGH-MATIC® Model 90 Screener: Part No. 25432 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 88WEIGH-MATIC® Model 90 Screener Control Unit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 89Junction Box Assembly: Part No. 25694 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 89WEIGH-MATIC® Model 90 Screener Power Units . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 90Model 90 Bin Fill Cap Kit: Part No. 25806 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 91Model 75 Bin Fill Cap Kit: Part No. 6563 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 91

Floor Feeder Miscellaneous ComponentsHens Only Grill (for Pan Breeder Feeder) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 92Program Gauge: Part No. 14251 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 92Control Shield: Part No. 24887 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 92Winch Control: Part No. 34812 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 93Winchable Feed Level Tube Components . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 94

6

Control Units

Item Description Part No.

1 Safety Hook 19802* Grill Lock 32943 Flat Bottom Pan 8892

Deep Pan 1654Shallow Pan 8892

4 Control Unit Grill Assembly 18915 Agitator Assembly 20406 Paddle Shield Assembly 28567 Shield Retainer 28478 Shield 28549 6-32 x 7/8” Screw 192110 SPDT Switch 190111 Tube Clamp 2406312 Switch Insulation 1907-213 Washer 14914 6-32 x 7/8” Screw 192115 Adjusting Bracket 297216 1/16” Cable Clamp 182617 Switch Bracket Assembly 284618 6-32 Hex Nut 77119 Control Adjustment Bracket 232620 Left Hand Side Bracket 188021 Top Closure Assembly 2512122 Anti-Roost Guard 279823 Wing Nut (1/4-20) 163024 Outlet Tube Assembly 457025 Paddle 285326 Receptacle Box Cover (220) 4169

Receptacle Box Cover (110) 202727 Receptacle (220) 4227

Receptacle (110) 202828 Side Panel Assembly (220) 4267

Side Panel Assembly (110) 2857-129 Side Bracket (R.H.) 187930 Strain Relief Bushing 541231 Handy Box 114532 Cord Assembly (220) 8301

Cord Assembly (110) 714-134 Cord Set (220) 4999-30

Cord Set (110) 190035 Bottom Closure 189036 Control Body Assembly 456837 1/4-20 x 1/2” Screw 162938 Receptacle Shield 773239 Extension Ass’y (Mod. 2000)884640 5/16-18 x 1/2” Hex Hd. Bolt 183941 5/16-18 Hex Lock Nut 214842 Coil 286043 Feed Baffle 14230

Model C & CT Control Unit

Part No: 1878-8

Manufactured from November 1983 to August 1988.


1 Safety Hook 19802* Grill Lock 32943 Flat Bottom Pan 8892

Deep Pan 1654Shallow Pan 8892

4 Control Unit Grill Assembly 18915 Agitator Assembly 20406 Paddle Shield Assembly 28567 Shield Retainer 28478 Shield 28549 6-32 x 7/8” Screw 192110 SPDT Switch 190111 Tube Clamp 2406312 Switch Insulation 1907-213 Washer 14914 6-32 x 7/8” Screw 192115 Adjusting Bracket 297216 1/16” Cable Clamp 182617 Switch Bracket Assembly 284618 6-32 Hex Nut 77119 Control Adjustment Bracket 911820 Left Hand Side Bracket 188021 Top Closure Assembly 2512122 Anti-Roost Guard 279823 Wing Nut (1/4-20) 163024 Outlet Tube Assembly 457025 Paddle 285326 Receptacle Box Cover (220) 4169

Receptacle Box Cover (110) 202727 Receptacle (220) 4227

Receptacle (110) 202828 Side Panel Assembly (220) 4267

Side Panel Assembly (110) 2857-129 Side Bracket (R.H.) 187930 Strain Relief Bushing 541231 Handy Box 114532 Cord Assembly (220) 8301

Cord Assembly (110) 714-134 Cord Set (220) 4999-30

Cord Set (110) 190035 Bottom Closure 189036 Control Body Assembly 456837 1/4-20 x 1/2” Screw 162938 Receptacle Shield 773239 Extension Ass’y (Mod. 2000)884640 5/16-18 x 1/2” Hex Hd. Bolt 183941 5/16-18 Hex Lock Nut 214842 Coil 286043 Feed Baffle 14230

Model 2000 Control Unit

Part No: 1878-9

Manufactured from November 1983 to April 1991.


Control Units


Control Units


1 Safety Hook 19802* Grill Lock 32943 Flat Bottom Pan 88924 Control Unit Grill Assembly 18915 Agitator Assembly 20406 Paddle Shield Assembly 28567 Shield Retainer 28478 Shield 28549 6-32 x 7/8” Screw 192110 SPDT Switch 190111 Tube Clamp 2406312 Switch Insulation 1907-213 Washer 14914 6-32 x 7/8” Screw 192115 Adjusting Bracket 297216 1/16” Cable Clamp 182617 Switch Bracket Assembly 284618 6-32 Hex Nut 77119 Control Adjustment Bracket 232620 Left Hand Side Bracket 1880


21 Top Closure Assembly 2512122 Anti-Roost Guard 279823 Bracket Support Weldment 2510824 Reinforcement Plate 2512725 Paddle 285326 Receptacle Box Cover 416927 Receptacle 422728 Handy Box & Cord Assembly426729 Side Bracket (R.H.) 2513430 Strain Relief Bushing 541231 Handy Box 114532 Cord Assembly 830133 Extension Assembly - - - -34 Cord Set 4999-3035 Bottom Closure 2512636 Control Body Assembly 456837 10-24 x 3/8” Screw 2512438 Receptacle Shield 773239 Feed Baffle 1423040 5/16-18 x 1/2” Hex Hd. Bolt 183941 5/16-18 Hex Lock Nut 214842 Extension Assembly 8846

Model C & CT Control Unit

Part No: 1878-8

Manufactured from August 1988 to

present.


Control Units


1 Control Top Cover 144332 Insulator 29763 Support Bracket 246834 Insert Assembly 62555 Feed Level Tube 25086 Feed Level Ring 81717 Grill Assembly 62698 Pan 77009 Switch Bracket 1443510 Anchor 418811 Control Box 1443412 Switch Box Mount 2508413 Gasket 6968-114 10-32 Locknut 696315 Spring 6972

Model C End Control Unit

Part No: 24396

Manufactured from 1989 to January 1994.


16 Paddle 2484817 Stop Panel 2543318 Switch Box Cover 677619 Switch Box 2470220 Control Cord Assembly 2549521 1/2” Watertight Connector 2698022 Gasket 677723 Switch 711424 Bottom Cover 1443225 Mylar 2531826 Paddle Retainer 2504527 Liquid Tight Connector 2468528 Switch Bracket 7068-- Actuator Pin 6775-- Danger Decal 2527-9-- Anti-Roost Guard 2798


Control Units

Model C End Control Unit

Part No: 24396 (1-Phase), 27757 (3-Phase)

Manufactured from January 1994 to present.

1 Phase 3 PhaseItem Description Part No. Part No.

1 Cover & Insulator Ass’y 24682 246822 Insulator 2976 29763 Support Bracket 24683 246834 Insert Assembly 6255 62555 Feed Level Tube 2508 25086 Feed Level Ring 8171 81717 Grill Assembly 6269 62698 Feeder Pan 7700 77009 Deflector Panel 34310 3431010 Anchor 4188 418811 Control Body 14434 1443412 Switch Box Mount 25084 2508413 Gasket 6968-1 6968-114 10-32 Lock Nut 6963 696315 Spring 6972 697216 Paddle 24848 2484817 Stop Panel 25433 2543318 Switch Box Cover 6776 6776


19 Switch Box 24702 784120 Control Cord Assembly 25495 - - - -21 1/2" Watertight Connector26980 - - - -22 Gasket 6777 677723 Actuator Switch 7114 711424 Bottom Cover 14432 1443225 Mylar 25318 2531826 Paddle Retainer 25045 2504527 Liquid Tight Connector 24685 - - - -28 Mylar Insulation 1907-5 1907-529 Terminal Block - - - - 34925-330 Switch Bracket 7068 706831 Mount Bracket 34309 3430932 14" Flexible Conduit 26982-1 - - - -33 90 Degree Connector 23810 23810-- Switch Actuator Pin 8757 8757-- Danger Decal 2527-9 2527-9-- Anti-Roost Guard 2798 2798


Control Units

Model C2 End Control Unit


Manufactured from April 1991 to present.


1 Cover & Insulator Ass’y 24682 246822 Insulator 2976 29763 Support Bracket 24683 246834 Support Cone Assembly 35729 357295 Switch Bracket 7068 70686 Control Unit Sleeve 29349 293497 Grill Assembly 25280 252808 Feeder Pan 25281 252819 Deflector Panel 34310 3431010 Anchor 4188 418811 Control Body 14434 1443412 Switch Box Mount 25084 2508413 Gasket 6968-1 6968-114 10-32 Locknut 6963 696315 Spring 6972 697216 Paddle 24848 2484817 Stop Panel 25433 2543318 Switch Box Cover 6776 6776


19 Switch Box 24702 784120 Control Cord Assembly 25495 - - - -21 1/2" Watertight Connector26980 - - - -22 Gasket 6777 677723 Actuator Switch 7114 711424 Bottom Cover 14432 1443225 Mylar 25318 2531826 Paddle Retainer 25045 2504527 Liquid Tight Connector 24685 - - - -28 Terminal Block - - - - 34925-329 Mylar Insulation 1907-5 1907-530 Mount Bracket 34309 3430931 Switch Actuation Pin 8757 875732 14" Flexible Conduit 26982-1 - - - -33 90 Degree Connector 23810 23810-- Switch Actuator Pin 8757 8757-- Danger Decal 2527-9 2527-9-- Anti-Roost Guard 2798 2798


Control Units


1 Cone Assembly 254902 Pan 249014 Support Bracket 246835 Insulator 29766 Gasket 67777 Control Top Cover 144338 10-32 Locknut 69639 Spring 697210 Gasket 6968-111 Paddle 2484812 Stop Panel 2543313 Switch Bracket 14435

Model H2 End Control Unit

Part No: 24397

Manufactured from 1988 to May 1990.


14 Control Box 1443415 Anchor 418816 1/4-20 x 1/2” Hex Hd. Bolt 148717 Switch Box Mount 2508418 Switch Box Cover 677619 Switch Box 2470220 Control Cord Assembly 2549521 1/2” Watertight Connector 2698022 Actuator Switch 7114-- Actuator Pin 6775-- Danger Decal 2527-9-- Anti-Roost Guard 2798


Control UnitsModel H2 End Control Unit


Part No. 24397: Manufactured from May 1990 to present.

Part No. 27762: Manufactured from January 1991 to present.


1 Pan 24901 249012 Cone Assembly 34481 344813 Switch Bracket 34309 343094 Switch Bracket 7068 70685 Bottom Cover 14432 144326 Control Assembly Cover 24682 246827 Insulator 2976 29768 Support Bracket 24683 246839 Deflector Panel 34310 3431010 Anchor 4188 418811 Control Body 14434 1443412 Switch Box Mount 25084 2508413 Gasket 6968-1 6968-114 10-32 Locknut 6963 696315 Spring 6972 697216 Paddle 24848 2484817 Stop Panel 25433 25433


18 Terminal Strip - - - - 34925-319 Switch Box 24702 784120 Cord Assembly 25495 - - - -

Reducing Seal 7815 - - - -21 1/2" Watertight Connector26980 - - - - 22 Actuator Switch 7114 711423 Gasket 6777 677724 Switch Box Cover 6776 677625 1/2" Watertight Connector24685 - - - -26 Paddle Retainer 25045 2504527 Mylar Assembly 25318 2531828 Switch Insulation 1907-5 1907-529 14" Flexible Conduit 26982-1 - - - -30 90 Degree Connector 23810 23810-- Anti-Roost Guard 2798 2798-- Switch Actuation Pin 8757 8757-- Danger Decal 2527-9 2527-9


Control Units


1 Control Top Cover 144332 Insulator 29763 Support Bracket 246834 Sleeve Assembly 246865 Support Cone 83346 Adjustment Ring 77287 Feeder Grill 77308 Shallow Pan 8764

Deep Pan 246779 Switch Bracket 1443510 Anchor 418811 Control Box 14434

Model 2000 End Control Unit

Part No: 24395-0

Manufactured from February 1989 to January 1994.


12 Switch Box Mount 2508413 Gasket 6968-114 10-32 Locknut 696315 Spring 697216 Paddle 2484817 Stop Panel 2543318 Switch Box Cover 677619 Switch Box 2470220 Control Cord Assembly 2549521 1/2” Liquid Tight Connector 2698022 Gasket 677723 Switch 711424 Bottom Cover 14432-- Actuator Pin 6775-- Danger Decal 2527-9-- Anti-Roost Guard 2798

The Model 2000 End Control with the Shallow Pan may be ordered under Part No. 24395-1.

The Model 2000 End Control with the Deep Pan may be ordered under Part No. 24395-2.


Control Units

Model G End Control Unit


Manufactured from June 1992 to present.


1 Anchor 4188 41882 Control Body 14434 144343 Switch Bracket 14435 144354 Paddle Retainer 25045 250455 Stop Panel 25433 254336 Paddle 24848 248487 Spring 6972 69728 10-32 Locknut 6963 69639 Gasket 6968-1 6968-110 Switch Box Mount 25084 2508411 Mylar Assembly 25318 2531812 3-Terminal Block - - - - 27845-313 Bottom Cover 14432 1443214 Support Cone 28134 2813415 Control Adjustment Cone 29064 2906416 Feeder Pan 7700 7700


17 Model G Grill Assembly 29300 2930018 Control Unit Sleeve 29349 2934919 Support Bracket 24683 2468320 Cord Stock 5044-3 - - - - 21 Reducing Seal 7815 - - - - 22 Vinyl Tubing 7814 - - - -23 1/2" Watertight Connector24685 2468524 1/2" Watertight Connector24680 2468025 Switch Insulation 1907-5 1907-526 Switch Box 24702 784127 Actuator Switch 7114 711428 Switch Bracket 7068 706829 Control Cord Assembly 25495 - - - - 30 14” Flexible Conduit 26982-1 - - - -31 90 Degree Connector 23810 23810-- Anti-Roost Guard 2798 2798-- Danger Decal 2527-9 2527-9-- Anti-Roost Guard 2798 2798


Control Units


1 Anti-Roost Guard 27983 Cover Assembly 56874 Anti-Roost Insulator Bracket 295165 Body Weldment 290566 Tube Clamp 295207* Diaphragm Assembly 48898* Spacer Plate 49219* Paddle 489010 Paddle Guard 489211* Housing 604812* 10-24 x 1/4” Screw 4417-213 Cover 605314* 4-40 x 3/4” Screw 4143-215* Actuator Switch 604916* Spring 582017* Barrier 693618* 10-32 x 7/8” Screw 4303-519* Switch Bracket 604520* 4-40 Hex Nut 351121* 6-32 x 5/16” Screw 4402-322* Wire Lead Assembly 2243-10623* 90° Connector 422824* Flex Cable 20140-425* Flex Connector 604226 Control Drop Tube 418027 Bottom Plate 418628 Handy Box 114529 Romex Connector 1317

Adult Turkey Feeder Control Unit

Part No: 6035

Manufactured from 1977 to May 1990.


30 Turkey Pan 419331 Handy Box Cover Plate 71132 Feed Level Tube 434133 Feed Level Ring 419634 Pan Support 419935 Drive Rivet 420036 Pan Shield 419037 Anchor Plate 418838 Cord Guard 199239 Cord Assembly 416640 Safety Closure 418441 “S” Hook 280542 1/4-20 x .4” Screw 275443 Spiroband 5915

* These items may be ordered as an assembly under Part No. 6044-1


Control Units


1** Danger Decal 2527-92** Tube Support 278913** Handy Box 11454** Stub Tube Weldment 279005** Insulator 29766** Body Cover 279427 Anti-Roost Guard 27988** Safety Cover Assembly 279419** Cover 71110** Danger Decal 2527-2511** Bottom Plate 2789312 Conduit Assembly 20140-413 Pan Support 4199


Part No: 6035

Manufactured from May 1990 to January 1991.


14* Drop Tube Assembly 605215 Feed Level Tube Assembly 434116 Plastic Feeder Pan 29000

Metal Feeder Pan 419317 Swing Down Pan Support 2427418** Control Body 2788919 3/8” Flexible Cable 20140-13-- Actuator Pin 8757-- Anchor Plate 4188

*See separate Parts List for Drop Tube Assem-bly on page 19.

**These components may be ordered as an assembly under Chore-Time Part No. 27899.


Control Units


1** Danger Decal 2527-92** Tube Support 278913** Mount Plate 286154** Stub Tube Weldment 279005** Insulator 29766** Body Cover 279427 Anti-Roost Guard 27988** Safety Cover Assembly 279419** Weatherproof Box 2866010** Danger Decal 2527-2511** Bottom Plate 2789312 Conduit Assembly 2797413 Pan Support 4199


Part No: 6035

Manufactured from January 1991 to present.


14* Drop Tube Assembly 2807215 Feed Level Tube Assembly 434116 ATF Plastic Feeder Pan 29000

ATF Metal Feeder Pan 419317 Swing Down Pan Support 2427418** Control Body 27889-- Actuator Pin 8757-- Anchor Plate 4188

*See separate Parts List for Drop Tube Assem-bly on page 19.

**These components may be ordered as an assembly under Chore-Time Part No. 27770.


Control UnitsAdult Turkey Feeder Drop Tube Assembly

Part No. 28072Item Description Part No.

1 Control Drop Tube Weldment41802 Cover 60533* Switch Assembly 6044-34 Guard Assembly 48925 90 Degree Connector - - - - 6 Switch Bracket Assembly 60457 Barrier 69368 3/8 Flex Connector - - - -9 Anti-Short Bushing - - - -10 Conduit Assembly 2786611 Paddle 489012 Diaphragm Assembly 488913 Spacer Plate 492114 Actuator Switch 604915 Housing 604816 Torsion Spring 5820

*Individual components include Items 5 thru 16.

Part No. 6052Item Description Part No.

1 Control Drop Tube Weldment41802 Cover 60533* Switch Assembly 6044-14 Guard Assembly 48925 90 Degree Connector 4228 6 Switch Bracket Assembly 60457 Barrier 69368 3/8 Flex Connector 60429 Anti-Short Bushing 630410 Flexible Cable 20140-411 Paddle 489012 Diaphragm Assembly 488913 Spacer Plate 492114 Actuator Switch 604915 Housing 604816 Torsion Spring 5820

*Individual components include Items 5 thru 16.



1 Safety Hook 19802 Grill Lock 32943 Epoxy Coated Pan 88924 Control Grill Assembly 18915 Agitator Assembly 20406 Paddle Shield Assembly 28567 Shield Retainer 28478 Shield 28549 6-32 x 7/8” Screw 192110 SPDT Switch 190111 Tube Clamp 2406312 Switch Insulation 1907-213 Washer 14914 6-32 x 7/8” Screw 192115 Adjusting Bracket 297216 Switch Bracket Assembly 284617 6-32 Hex Nut 77118 Cover 575519 Insulator 575420 #10 x 1/2” Screw 303721 Outlet Tube Assembly 457022 Outlet Tube Assembly 531923 Paddle 285324 1/4-20 Hex Nut 75125 1/4-20 x 7/8” Screw 148826 1/4-20 x 1/2” Screw 148727 *Control Adjustment Bracket 9118

Control Adjustment Bracket 232628 1/4” Hex Lock Nut 126929 1/4” Flat Washer 323930 Strain Relief Bushing 71531 10-24 x 1/2” Screw 1795

Model C, CT, H, & 2000 Intermediate Control Unit

Part No: 5302-0Item Description Part No.

32 #10 External Washer 30533 10-24 P.M. Nut 13534 Cord Set 4999-1335 Control Body Assembly 456836 5/16-18 Hex Lock Nut 214837 5/16-18 x 1/2” Screw 183938 *Extension Assembly

*Part are common for the 5302-1 & 5302-5 Intermedi-ate Control Unit, except parts noted with an(*). These parts are required on the 5302-5 version only.

Note: Part No. 5302-1 Intermediate Control Unit is used with the Model C, CT, and H Feeding Systems.

Part No. 5302-5 Intermediate Control Unit is used with the Model 2000 Feeding System.

Control Units

Part No. 5302-1: Manufactured from 1974 to February 1994.

Part No. 5302-5: Manufactured from 1986 to February 1994.



1 Feeder Pan 77002 Grill Assembly 62693 Feed Level Ring 81714 Feed Level Tube 25085* Switch Box Cover 67766 Control Box Assembly 247187 Insert Assembly 62558 10-24 x 1-7/8” Screw 4416-49* Switch Box 2467810* Gasket 677711* Actuator Switch 711412* Switch Bracket 706813* Reducing Seal 781514* Vinyl Tubing 781415* Water Tight Connector 24685-- Spring 6972-- Switch Paddle 24848-- Mylar Assembly 25318

*These components may be ordered as an assembly under Chore-Time Part No. 24317.

**The Intermediate Control may be ordered without the Feeder Pan and Grill Assembly under Chore-Time Part No. 25422.

Model C & CT Intermediate Control Unit

Part No: 24190

Control Units

Manufactured from 1988 to February 1991.


Control Units

Manufactured from February 1991 to present.

Model C Intermediate Control Unit

Part No: 24190 (1-Phase), 27758 (3-Phase)1 Phase 3 Phase

Item Description Part No. Part No.

1 Feeder Pan 7700 77002 Grill Assembly 6269 62693 Feed Level Ring 8171 81714 Feed Level Tube 2508 25085 10-24 x 1-7/8” Screw 4416-4 4416-46 Front Panel 25046 250467 Insert Assembly 6255 62558 Switch Box 34842 78419 Switch Box Cover 6776 677610* Gasket 6777 677711* Actuator Switch 7114 711412* Switch Bracket 7068 706813* Reducing Seal 7815 - - - -14* Vinyl Tubing 7814 - - - -15* Water Tight Connector 24685 - - - -16 Danger Decal 2527-9 2527-9


17 Tube Support 14754 1475418 Switch Paddle 24848 2484819 Tube Retainer 14756 1475620 Mylar Assembly 25318 2531821 Back Cover 25047 2504722 Terminal Block 34925-2 34925-223 Switch Insulation 1907-5 1907-5-- Spring 6972 6972-- Gasket 6968-1 6968-1-- Danger Decal 2527-25 2527-25-- Pivot Bracket 25048 25048-- Paddle Retainer 25045 25045



Control Units


Model C2 Intermediate Control Unit

Part No: 28117 (1-Phase), 28275 (3-Phase)1 Phase 3 Phase


1 Feeder Pan 25281 252812 Feeder Grill 25280 252803 Tube Support 14754 147544 Support Cone Assembly 35729 357295 10-24 x 1-3/4” Screw 4416-4 4416-46 Switch Box 34842 78417 Gasket 6777 67778 Switch Box Cover 6776 67769 Vinyl Tubing 7814 - - - -10 Switch Bracket 7068 706811 Actuator Switch 7114 711412 Water Tight Connector 24685 - - - -13 Reducing Seal 7815 - - - -14 Front Panel 25046 2504615 Back Cover 25047 2504716 Tube Retainer 14756 14756


17 Danger Decal 2527-9 2527-918 Terminal Block - - - - 34925-219 Control Unit Sleeve 29349 2934920 Switch Insulation 1907-5 1907-5-- Pivot Bracket 25048 25048-- Paddle Retainer 25045 25045-- Spring 6972 6972-- Switch Paddle 24848 24848-- Mylar Assembly 25318 25318

The Intermediate Control may be ordered without the Pan, Grill, Adjustment Cone, and Support Cone Assembly under Chore-Time Part No. 25422.


Control Units


Model 2000 Intermediate Control Unit

Part No: 24191-1 (shallow pan), 24191-2 (deep pan)

24191-1 24191-2Item Description Part No. Part No.

1 Feeder Pan 8764 87642 Feeder Grill 7730 77303 Sleeve Assembly 24686 246864 Adjustment Ring 7728 77285 10-24 x 1-3/4” Screw 4416-4 4416-46* Switch Box 24678 246787* Gasket 6777 67778* Switch Box Cover 6776 67769* Vinyl Tubing 7814 781410* Switch Bracket 7068 706811* Actuator Switch 7114 711412* Water Tight Connector 24685 2468513* Reducing Seal 7815 781514 Support Cone 8334 833415 Control Box Assembly 24718 24718-- Spring 6972 6972-- Switch Paddle 24848 24848-- Mylar Assembly 25318 25318


The Intermediate Control may be ordered without the Pan, Grill, Sleeve Assembly, and Adjusting Ring, under Chore-Time Part No. 25422.


Control Units


Model G Intermediate Control Unit



1 Tube Retainer 14756 147562 Danger Decal 2527-9 2527-93 Support Cone Assembly 35729 357294 Model G Grill Assembly 29300 293005 Feeder Pan 7700 77006 Control Cord Assembly 4999-49 - - - -7 Control Unit Sleeve 29349 293498 Switch Box Cover 6776 67769 Danger Decal 2529-380 2529-37910 Switch Box 34842 784111 Front Panel 25046 2504612 Back Cover 25047 2504713 16-3 SJO Cord 2290-2 - - - -14 1/2” Water Tight Conn. 24685 - - - -15 Actuator Switch 7114 711416 Mylar Assembly 25318 25318


17 Paddle Switch 24848 2484818 Switch Bracket 7068 706819 2-Terminal Block - - - - 34925-220 Vinyl Tubing 7814 - - - -21 Reducing Seal 7815 - - - -22 Switch Insulation 1907-5 1907-523 Tube Support 14754 1475424 Pivot Bracket 25048 2504825 Paddle Retainer 25045 2504526 Switch Box Cover Gasket 6777 6777-- Switch Box Leveling Gasket 6972 6972-- Gasket 6968-1 6968-1-- Switch Actuation Pin 8757 8757



1 Feeder Pan 249012 Cone Assembly 254903 10-24 x 1-3/4” Screw 4416-44 Tube Retainer 147565 1/2” Water Tight Connector 246856 Reducing Seal 78157 Vinyl Tubing 78148 Actuator Switch 71149 Switch Bracket 706810 Switch Box 2467811 Switch Box Cover 677612 Gasket 6777

Model H2 Intermediate Control Unit

Part No: 25435

Control Units



Control Units

Model H2 Intermediate Control Unit



1 Pan 24901 249012 Cone Assembly 34481 344813 Terminal Block - - - - 34925-24 Tube Support 14754 147545 10-24 x 1-3/4” Screw 4416-4 4416-46 Switch Box 34842 78417 Gasket 6777 67778* Switch Box Cover 6776 67769 Danger Decal 2527-9 2527-910 Tube Retainer 14756 1475611 Front Panel 25046 2504612 Back Cover 25047 2504713 Switch Paddle 24848 24848


17 Water Tight Connector 24685 - - - -18 Vinyl Tubing 7814 - - - -19 Reducing Seal 7815 - - - -20 Switch Insulation 1907-5 1907-514 Mylar Assembly 25318 2531815 Switch Bracket 7068 706816 Actuator Switch 7114 7114-- Spring 6972 6972-- Gasket 6968-1 6968-1-- Switch Actuation Pin 8757 8757-- Pivot Bracket 25048 25048-- Paddle Retainer 25045 25045

Part No. 25435: Manufactured from July 1989 to present.

Part No. 27760: Manufactured from January 1991 to present.



1 Insulator 57542 Drop Tube Weldment 64463 Paddle Guard 67714* Diaphragm Assembly 48895* Spacer Plate 49216* Paddle 48907* Housing 60488* 10-24 x 1/4” Screw 4417-29 Cover 605310* 4-40 x 3/4” Screw 4143-211* Actuator Switch 604912* Spring 582013* Barrier 693614* 10-32 x 7/8” Screw 4303-515* Switch Bracket Assembly 604516* 4-40 Hex Nut 351117* 6-32 x 5/16” Screw 4402-318* 90° Connector 422819* Flex Cable 20140-520* Flex Connector 604221* Wire Lead Assembly 2243-11222* Anti-Short Bushing 630423 Pan Shield Support 6443-- Feed Level Tube 4341

*Indicates components of Switch Assembly Part No. 6044-2.

Adult Turkey Feeder Intermediate Control Unit

Part No: 6039

Control Units



Power Unit

Motor H.P. Type Hz. Gearhead RPM Pinion Motor Shield

3259-1 2599 1/4 SP 60 3261-1 216 3249R N/A

3259-2 1854 1/6 SP 60 3261-1 216 3249R N/A

3259-7 4229 1/3 SP 60 3261-1 216 3249R 4266-Doer, 6815-GE, 6781-EM,

3259-8 4229 1/3 SP 60 3261-5 348 5046R 4266-Doer, 6815-GE, 6781-EM,

3259-25 5703 1/2 SP 60 3261-5 348 5046R 6815-GE

3259-26 3967 1/4 SP 60 3261-1 216 3249R 6815-GE,6781-EM

3259-29 5976 1/3 C 50 3261-1 180 3249R 4266-Doer,5711-GE

3259-30 5977 1/2 C 50 3261-5 293 5046R 4266-Doer,5711-GE

3259-34 4229 1/3 SP 60 3261-5 348 5046R 6815-GE, 6781-EM

3259-39 5703 1/2 SP 60 3261-5 348 5046R N/A

3259-41 5977 1/2 C 50 3261-5 293 5046R N/A

3259-51 5050 1/2 C 60 3261-7 348 5046R N/A

3259-53 6305 3/4 C 50 3261-7 285 5046R N/A

3259-55 7520 1/4 SP 60 3261-1 216 3249R 6815-GE, 6781-EM

3259-56 7520 1/4 SP 60 3261-1 216 3249R 6815-GE, 6781-EM

3259-57 7522 3/4 C 60 3261-5 696 5046R 6772-GE,6815-EM

3259-58 4229 1/3 SP 60 3261-5 348 5046R 6815-GE,6781-EM

3259-59 5703 1/2 -- 60 3261-5 348 5046R 6815

3259-60 exp 5977 1/2 C 50 3261-5 290 5046R 5711-GE

3259-61 4229 1/3 SP 60 3261-1 216 3249R 6815-GE,6781-EM

Floor Feeder Power Units

Power Units


3259-62 7520 1/4 SP 60 3261-1 216 3249R 6815-GE,6781-EM

3259-63 5976 1/3 C 50 3261-1 180 3249R 5711-GE

3259-77 5050 1/2 C 60 3261-10 425 5046R N/A

3259-78 5050 3/4 C 60 3261-10 425 5046R N/A

3259-79 6847 1 C 60 3261-10 425 6104R N/A

3259-81 7522 3/4 C 50/60 3261-11 708 5046R N/A

3259-82 7520 1/4 SP 60 3261-1 216 3249R N/A

3259-83 4229 1/3 SP 60 3261-1 216 3249R 6815-GE,6781-EM

3259-84 4229 1/3 SP 60 3261-5 348 5046R 6815-GE,6781-EM

3259-85 5703 1/2 SP 60 3261-5 348 5046R 6815-GE

3259-86 5976 1/3 C 50 3261-5 288 5046R 5711-GE

3259-98 5477 1/2 C 50 3261-11 5046R N/A

3259-100 28031 1/2 3-PH 50 3261-11 348 5046R N/A

3259-101 28032 3/4 3-PH 50 3261-11 696 5046R N/A

Power Unit

Motor H.P. Type Hz. Gearhead RPM Pinion Motor Shield

Floor Feeder Power Units

Power Units


Floor Feeder Power Unit Miscellaneous Components

Power Units


1 Pinion Assembly--216 RPM 3249R--348 RPM 5046R--354 RPM 4450

5 Motor - - - -*6 5/16-18 x 3/4” Screw 4412-1R7 Gearhead Assembly - - - -**8 1/4-20 x 1-1/2” Screw 29199 Pipe Plug 2755R10 Flat Washer 148411 Drive Tube

--3/4” O.D. 1048--7/8” O.D. 2920

12 Drive Block 464213 Vented Plug 3523R14 Ground Wire (16 AWG) 2243-17815 Anti-Short Bushing 630416 90° Connector 4228

Connector 131717 Wire Lead Assembly

--without terminal 2243-134--with terminal 2243-138


18 Cord Assembly - - - -***19 Cord Guard

--for 1/3 H.P. Motor 4168--for 1/2 H.P. Motor 5712

20 90° Liquid Tight Connector 795321 Flexible PVC Tubing 8028-122 “8” Hook 275923 5/16” Flat Washer 223024 5/16-18 x 1-1/4” Screw 4412-825 Hanger Bracket 847526 Motor Shield 678127 Motor Shield 426628 Motor Shield 677229 Motor Shield 681530 Motor Shield 571131 Motor Shield for ATF 297332 Cord Support 4327-- “S” Hook 4270-- Magnetic Pipe Plug 30160

*See individual Power Units on page 29-30.**See individual Gearheads on page 29-30.***Source Cord Assemblies locally.


Boot Components

Single Boot Components

Part No: 6822 (Broiler), 6821 (ATF)

6822 6821Item Description Part No. Part No.

1 Boot Weldment 3760 42242 Tube Clamp 24063 240633 Outlet Tube 4556 45564 Sleeve 5648 56485 3/16 x 1” Pin 2960-1 2960-16 Bearing 2689 26897 Washer 2955-14 2955-148 Anchor 6818 68189 Set Screw 1174 117410 Anchor & Bearing Ass’y 6817 681711 Cannonball 3531 353112 Cotter Pin 1639 163913 Chain 2128-1 2128-114 Latch Pin Assembly 2683 268315 Cap 29373 29373-- Danger Decal 2527-9 2527-9

Part No. 6821: Manufactured from October 1979 to present.



Boot Components

Twin Boot Components

Part No: 6824 (Broiler), 8460 (ATF)


1 Boot Weldment 3932 84612 Tube Clamp 24063 240633 Outlet Tube 4556 45564 Sleeve 5648 56485 3/16 x 1” Pin 2960-1 2960-16 Bearing 2689 26897 Washer 2955-14 2955-148 Anchor 6818 68189 Set Screw 1174 117410 Anchor & Bearing Ass’y 6817 2953011 Cannonball 3531 353112 Cotter Pin 1639 163913 Chain 2128-1 2128-114 Latch Pin Assembly 2683 268315 Cap 29373 29523-- Danger Decal 2527-9 2527-9




Boot Components

ULTRAPAN® Boot Assembly

Part No: 34824


1 Boot Weldment 348112 Agitator Assembly 348043 Agitator Ball 348033 Latch Pin Assembly 26834 Danger Decal 2527-95 5/16” U-Bolt 34823


Boot Components

ULTRAPAN® Intake Cup Assembly

Part No: 28119


1 Cup Weldment 245612 Anti-Roost Wire 296963 Hopper Sprocket 252864 Agitator Rod 245715 Spacer 245586 Clamping Bolt 245527 Insulator Mounting Strap - - - -8 Bearing Assembly 141449 1/4-20 Hex Nut 75110 1/4-20 x 5/8” Button Hd. Sc. 243211 3/32” Clamp 182612 7/16” Washer 2955-2513 1/4” Lock Washer 166714 Insulator 297615 Hopper Adapter 25165

Manufactured from May 1991 to November 1994.


Boot Components

ULTRAFLO® Intake Cup Assembly

Part No: 25167 (domestic) & 27380 (Intn’l only)


1 Intake Cup Weldment 25466 273832 Clamping Bolt 24552 245523 Spacer 24558 245584 7/16” Flat Washer 2955-25 2955-255 7/16” Lock Nut 2428 24286 Bearing Assembly 14144 141447 Actuator Rod 24571 295188 Restrictor Plate 37338 373389 Hopper Sprocket 25286 2528610 Hopper Adapter Weld. 25165 2516511 5/16-18 Wing Nut - - - - 214612 Flat Washer - - - - 593313 Baffle - - - - 2738214 Bearing Spacer 28646 28646


Feed Hoppers

100# Feeder Line Hopper

Key Description Part No.

1* Hopper Cover (w/o hole) 282112* Hopper Cover (w/ hole) 282123 Tube Support Assembly 143674 Hopper Hanger 281655 Adjustment Bracket 27066 Cotter Pin 2797-17 Hair Pin 26648 Hopper Side (w/o hole) 281649 Hopper Side (w/ hole) 2424110 Boot Hanger 2816811 H.L.C. Mounting Bracket 28267

NOTES*Items 1 & 2 may be ordered as an assembly under Part No. 28210.

The 100# Hopper Assembly (no Cover) may be ordered under Part No. 28220.

The 100# Hopper Assembly, including the Cover, may be ordered under Part No. 28240.

The 100# Hopper Assembly, including an 8798 Switch (not shown), may be ordered under Part No. 28242.

The 100# Hopper Assembly, including the Cover and an 8798 Switch, may be ordered under Part No. 28240.


Feed Hoppers


Part No: 9474


1 Hopper Cover (optional) 282062 Tube Support Assembly 14367

Clamp 13948Chain 2128-1

3 Hopper Side (w/o hole) 26804 Boot Hanger 26715 Hanger Bracket Assembly 26816 Adjustment Bracket (2 req’d)27067 Hair Pin 26648 Clevis Pin, 5/16 x 1" 2797-19* Diaphragm Assembly 790010* Boot Switch 784011 Hopper Side Panel (w/ hole) 8791

*These items are components of the 8798 Switch Kit. See separate parts listing for indi-vidual components.



1* Hopper Cover Kit (optional) 28206Cover Half (Removable) 28208Cover Half (Stationary) 28207

2 Tube Support Assembly 14367Clamp 13948Chain 2128-1

3 Hopper Side (4 req’d) 26804 Boot Hanger 26715 Hanger Bracket Assembly 26816 Adjustment Bracket (2 req’d)27067 Hair Pin 26648 Clevis Pin, 5/16 x 1" 2797-1

*Hopper Cover not included, must be ordered separately.

Feed Hoppers


Part No: 7941



1 Hopper Support 244272 Hanger Bracket Assembly 26813 Hopper Hanger 244264 Hopper Side 244235 Boot Hanger 244256* Diaphragm Assembly 79007* Deflector Shield 282818 Hopper Side (w/Switch Hole)244249* Mounting Plate 790810* Switch Box 784111* Gasket 677712* Switch Box Cover 677613* 6-32 x 7/8” Screw 192114* Pin 875715* Spring 697216* Switch Bracket 706817* SPDT Actuator Switch 711418* Paddle 789619* Switch Insulation 1907-5

Feed Hoppers



20* #10 Twin Helix Screw 698021 H.L.C. Support Plate 2826722** Hopper Cover (w/clamps) 2820223** Hopper Cover 2820324 Cover Plate 28369

*These components may be ordered as an assembly under Part No. 8798.

**These components may be ordered as an assembly under Part No. 28201.

Note: An Extension Kit for the 300# Hopper is available under Part No. 36319.

Hopper Assembly Part Numbers:

Hopper Assembly w/o Switch or Cover: 28359.Hopper Assembly w/ Cover only: 28360.Hopper Assembly w/ Switch only: 24436.



1 Hopper Hanger 244272 Hanger Bracket Assembly 26813 Hopper Brace 244264 Hopper Side 244235 Boot Hanger 244256** Diaphragm Assembly 79007** Boot Switch 79008 Switch Hopper Side 24424

**Components of the 8798 Lower Hopper Switch.

Feed Hoppers

300# Breeder Feeder Hopper



1 Hopper Cover 45202 Top Plate Weldment 45273 Leg Weldment 276154 Pulley Wheel 25035 Anchor 276096 Brace (L.H.) 27533-1

Brace (R.H.) 27533-27 Pawl 66728 Crank Arm Weldment 276139 Ratchet Weldment 2760410 Lower Leg Weldment 2761411 Cable Shaft 2761212 400# Hopper Extension 2760113 Hopper Side 483614 Hopper Ledge 483715 3/4” Set Collar 104916 Cable 27534

The hardware and miscellaneous components may be ordered under Chore-Time 27531 Hardware Package.

Feed Hoppers


(Part No. 27530)


Feed Hoppers

Lower Hopper Switch

(Part No. 8798)


1 6-32 x 7/8" Rd. Hd. M.S. 19212 SPDT Actuator Switch 71143 Switch Insulation 1907-54 Switch Bracket 70685 #6 x 3/8" Screw 67826 6-32 Hex Nut 7717 Pin 87578 Switch Box 78419 10-32 Hex Lock Nut 696310 Spring 697211 10-32 Hex Nut 429712 Mounting Plate 790813 #10 Twin Helix Screw 698014 Switch Box Cover 677615 Gasket 677716 Gasket 6968-117 Paddle 789618 Diaphragm Assembly 7900-- Deflector 28281


Feeder Line Components

Broiler, Cockerel, & ATF Feeder Line Components

(Model C, C2 H, H2, G, 2000)


1 1/16” Cable 19223/32” Cable 4973

2 Charger Wire (165’) 28994-165Charger Wire (330’) 28994-330

3 Poultry Trainer (110 V) 29333Poultry Trainer (220 V) 29325

4* Auger 6820-05 1/16” Cable Clamp 1826

3/32” Cable Clamp 18266 Spring 75517 Auger Tube

-12 ft., 5 Hole Tube 6854-6-12 ft., 4 Hole Tube 6854-7-10 ft., 4 Hole Tube 6854-4-10 ft., 3 Hole Tube 6854-5-9 ft., 4 Hole Tube 6854-1-10 ft., 1 Hole Tube (ATF) 6684-10 ft., 2 Hole Tube (ATF) 6685-10 ft., 3 Hole Tube (ATF) 6686


8 Line Charger (110 V) 29317Line Charger (220 V) 29341

9 Hanger (ATF only) 420710 Hanger Strap 729811 Hanger Bracket 729712 Hanger Kit 729913 Tube Clamp 24063

Tube Clamp (ATF) 2952014 Anti-Roost Bracket 24060

Anti-Roost Bracket (ATF) 2951615 Hanger Assembly 760416 Grommet 1489917 Feeder Lock 3457018 Feed Level Tube 8790

*Round up to the nearest 10’. Auger lengths from 50 to 500 feet. Example: 6820-200 would be a 200’ roll of 6820 Auger.


Feeder Line ComponentsULTRAPAN® Feeder Line Components


1 90 Degree elbow 281252 Tube Coupling (1-3/4" diameter)2123

Tube Coupling (2" diameter) 296913 Hanger 42074 Insulator Bracket 240605 Tube Clamp 24063

2" Tube Clamp 295206 3/32” Cable Clamp 18267 Spring 75518 Tube Adaptor 281079 Belled Adapter Tube 2969310+ Adjustable Hanger 1478011+ Grommet 1489912 Welding Fixture 2549413 Anti-Roost Wire 2810814 4’ Extension Tube 28128

+ These components may be ordered as an assembly under Chore-Time P/N 7604.* These components may be ordered as an assembly under Chore-Time P/N 28127.**The Auger may be ordered in lengths from 100’ to 330’. Include the specific length as a suffix to the part number (example: 28103-220 is a 220’ roll of auger).


15 Roll-Formed Feeder Tube--12’ /4 - hole 6854-7--10’ /4 - hole 6854-4

16** Auger 28103-017* Service Section Base 2815318* Service Section Clamp 2815119* Service Section Cover 2815220 1/16 Cable 192221 Poultry Trainer 2933322 Auger Driver 2812623 Line Charger 2931724 1/8" Cable Clamp 1489825 Hi-Voltage Cable (330’) 28994-330

Hi-Voltage Cable (165’) 28994-16526 Auger Connector 29055-227 S Hook 72328 Model C2 Lock 34570



ULTRAFLO® Feeder Line Components


1 90 Degree Elbow 251702*** Connector Tube 296913 5’ Belled Tube 356274 Trough -10’ (3 m) 14159-35 Grill End Cap 254646*** Tube Clamp 297757 End Cap 251698 Welding Fixture 254949 Trough Hanger 2501010 Clean-Out 2550211§ Auger 25058-012* Auger Connector Ass’y 28091-213 Clean-Out Lock 3586514 Clean-Out Assembly 35802

*includes two connectors & (4) set screws.

***(1) Connector Tube and (2) Tube Clamps may be ordered as a kit under part no. 29802.

§Round up to nearest 10 foot interval.



ULTRAFLO® Feeder Line Grill Options

*Denote number of c ross wires .

Part Nu m b e r

Gri l l S ty l e

Dimension “A” Dimension “B” Dimension “C”Gri l l

Reta iner

24774-5 Standa rd 2 .000” (50 .80 mm) N / A 4.50” (11 .43 cm) Not Requ i red





28644-1 Cross (2 )* 1 .653” (41 .99 mm) 2 .77” (70 .36 mm) 5 .51” (14 .00 cm) Not Requ i red






28244 Hi-Contour 1 .688” (42 .86 mm) 3 .00” (76 .20 mm) 5 .550” (14 .10 cm) 2 7 9 0 9




Grill Style: Standard Grill Style: Cross Grill Style: Hi-Contour


Standard Model C Feeder


1 Grill 69062 Grill Support 64613 Feed Level Tube 2508

Feed Level Tube for Turkeys43294 Feed Level Ring 81715 Plastic "V" Bottom Pan 7700

Model C Feeder (Slide Top)


1 Grill 69063 Feed Level Tube 2508

Feed Level Tube for Turkeys 43294 Feed Level Ring 81715 Plastic "V" Bottom Pan 77006* Support Cap 250527* Support Insert (swinging) 283568* Grill Support 25051

*These components may be ordered under Chore-Time Part No. 25055.

Feeder Assemblies

Model C


Feeder Assemblies

Model C2

Model C2 Feeder (Slide Top)


1 Grill 252802* Adjustment Cone 290643 Model C2 Feeder Pan 252814 Support Cap 250525 Support Insert (Swinging) 283566* Support Cone 252837 Model C2 Ass’y (Slide Top) 28115

*These items may be ordered as an assembly under Part No. 29514.

2-Piece Model C2 Feeder


1 Model C2 Feeder Pan 252812* Adjustment Cone 290643 Support Cone 252824 Grill 252805 2-Piece Model C2 Feeder 28110

1-Piece Model C2 Feeder(Note: This feeder is used with Cockerel Feeder Systems)


1 Model C2 Feeder Pan 252812 1-Pc Cone (windowless) 338853 Grill 252804 1-Piece Model C2 Feeder 34569


Feeder Assemblies

Model H


3 Shallow V Bottom Pan 58318 Pan Support Wire 58079 Feed Cone 5120

A Support Cone Repair Kit, consisting of (10) 7016 Repair Plates and (40) 3/16” Short Pop Rivets, may be ordered under Chore-Time Part No. 7017.


Feeder Assemblies

Model H2


1 Model H2 Cone (w/o Feed Windows) 24900-52 Model H2 Feeder Pan 249013 Feed Chute 25320-14 Model H2 Cone (w/ Feed Windows) 24900-65 Flood Collar 253606 Support Cap 250527 Support Insert (swinging) 283568 Model H2 Cone (Slide Top, w/o Windows) 24900-39 Model H2 Cone (Slide Top, w/Windows) 24900-410 Model H2 1-Piece Feeder (w/o Windows) 2711011 Model H2 1-Piece Feeder (w/ Feed Chute) 2711512 Model H2 1-Piece Feeder (w/ Flood Collar) 2712013 Model H2 2-Piece Feeder (w/o Windows) 2811214 Model H2 2-Piece Feeder (w/ Feed Chute) 2811315 Model H2 2-Piece Feeder (w/ Flood Collar) 28114


Feeder Assemblies

Model G

Model G Feeder (Slide Top)


1 Feeder Pan 77002* Support Cone 252833* Adjustment Cone 307304 Grill 293005 Support Insert (Swinging) 283566 Support Cap 250527 Model G Ass’y (Slide Top) 29565


2-Piece Model G Feeder


1 Feeder Pan 77002* Support Cone 252823* Adjustment Cone 307304 Grill 293005 2-Piece Model G Feeder 29560


1-Piece Model G Feeder


1 Feeder Pan 77002 1-Pc Cone (windowless) 338853 Grill 293004 1-Piece Model G Feeder 34567


Feeder Assemblies

Model 2000


1 Feeder Grill 7730Feeder Grill (split ring) 14150

3 Red Plastic Pan 7729Deep Plastic Pan 24000Shallow “V” Bottom Pan 24000

4 Feed Level Ring 77289 Feed Cone 7731

Feed Cone (field repair only)14949



1 Pan Shield 41922 Swing Down Pan Support 242743 Pan Support 41994 ATF Plastic Feeder Pan 290005* Insulator 57546 Pan Shield Support 64437* Drop Tube 57588 Feed Level Tube 41949 Feed Level Ring 29320

*These Items (#5 & #7) may be ordered as an assembly under Chore-Time Part No. 5806.

Feeder Assemblies

Adult Turkey Feeder


Suspension ComponentsMiscellaneous Components


1 3/32” Cable 49733/16” Cable 12131/8” Cable 27975

2 Cable Lock 143373 Pulley (w/Swivel) 30044 Double Eye Pulley 25015 Pulley 25006 3/16” Cable Clamp 732

1/8” Cable Clamp 148987 Standard Screw Hook 1214

Large Screw Hook 20418 7” Screw Hook 283579 Pulley Assembly 2842910 Ceiling Hook 2855011* Handle Shank 214812** Drill Adapter Shaft 315113 Winch Handle Pin 376114 Winch Drive Tube (4’) 2884-1

Winch Drive Tube (8’) 2884-215 Pulley 250316 Clevis Pin 2498-1


17 Side Bracket 252218 Spacer 252419 Eye Bolt 636220 Foot 158621 Cable Assembly 2809-222 Double Sheave Pulley 250223 Screw Hook Driver (short) 13150-1

Screw Hook Driver (long) 13150-224 Hand Winch Bracket 119325 Hand Winch 1212

Item 11 and 13 may be ordered as a kit under Part No. 2885.

Item 12 and Item 13 may be ordered as a kit under Part No. 2886.

The Full Line Suspension Kit including items 15 through 21 may be ordered under Part No. 7948.


Suspension Components

Power Winch: Part No. 2883


1 Input Shaft Assembly 148852 Flange Bushing 2967-23 Drive Stud 4128-14 Shoulder Bolt 4022-25 Pawl 66726 5/16" Flat Washer 2955-447 Spring 15438 Spring Washer 40239 Intermediate Gear 289010 Flange Bushing 325211 Spirol Pin 2960-312 Bushing 2967-413 Washer 2955-114 Retaining Ring 2958-1


15 Drive Pinion 296216 Woodruff Key 295917 1" Bearing 493718 Spacer 493619 Retaining Ring 355620 Washer 2955-221 Winch Drum 372322 Drum Shaft 363723 Setscrew 60324 Winch Frame 371925 Setscrew 372726 Cable Hook 298527 Grease Zerk 2449928 Washer 2499



Electric Power Lift: Part No. 14580


1 Power Unit 3259-72 5/16-18 x 3/4” H.H. Screw 2046

5/16” Flat Washer 22303 1/4-20 Lock Nut 12694 Power Winch 28835 5/16” Washer 22306 5/16-18 Hex Nut 21487 5/16-18 x 2-1/2” H.H. Bolt 27538 3/8-16 x 1” H.H. Bolt 25559 3/8” Washer 496710 3/8” Patch Lock Nut 218311 5/16-18 x 3/4” H.H. Screw 204612 5/16” Locknut 214813 Input Shaft Assembly 1488514 1/4-20 x 1-1/2” S. H. Screw 5083-815 Universal Joint 2784016 Power Unit Bracket 1458717 Winch Bracket 24401-- Switch Box Assembly 14613

• The entire assembly, except Item #4, may be ordered under Part No. 14560 Electric Winch Kit.

• The entire assembly, except Items #1 & #4, may be ordered under Part No. 24508 Power Lift Parts Kit.

Manufactured from April 1986 to October 1990.



Electric Power Lift: Part No. 14580


1 Power Unit 3259-72 5/16-18 x 3/4” H.H. Screw 2046

5/16” Flat Washer 22303 1/4-20 Locknut 12694 Power Winch 28835 5/16” Washer 22306 5/16-18 Hex Nut 21487 5/16-18 x 2-1/2” H.H. Bolt 27538 3/8-16 x 1” H.H. Bolt 25559 3/8” Washer 496710 3/8” Patch Lock Nut 218311 5/16-18 x 3/4” H.H. Screw 204612 5/16” Locknut 214813 Input Shaft Assembly 1488514 1/4-20 x 1-1/2” S. H. Screw 5083-815 Universal Joint 2784016 Power Unit Bracket 1458717 Winch Bracket 24401-- Switch Box Assembly 14613

• The entire assembly, except Item #4, may be ordered under Part No. 14560 Electric Winch Kit.

• The entire assembly, except Items #1 & #4, may be ordered under Part No. 24508 Power Lift Parts Kit.

Manufactured from November 1990 to Present



Switch Box (for Electric Power Lift): Part No. 14316


1 Box and Cover 146112 Momentary Switch 57853 Toggle Switch 60144 Grounding Plate 146045 Toggle Switch Boot 17396 Push Button Boot 20784


This page is left blank intentionally.


Electrical Controls and Components

Breeder Control Panel: Part No. 34380


1 Control Box 30860-42 Clear Cover 30859-13 Control Box Latch Pivot 308634 Control Box Latch 308625 Fuse Holder 244316 Control Box Mount Panel 348527 Back Mount Panel 345648 Front Panel 345659 Time Clock Connector 3445710 Terminal Strip 34925-811 Terminal Mount Bracket 3509412 3 Amp Fuse (Slow Blow) 2047213 Terminal Mount Bracket 34563

Item Description Part No

14 Terminal Strip 3492515 P & B Relay (240 V) 3473316 Transformer 3457117 Mount Bracket 3456218 Battery Box Assembly 3509519 AAA Battery 3458420 Terminal Block 734721 Pilot Light 2970822 Toggle Switch 3457923 Toggle Switch 3438924 Toggle Switch 3457825 MOV 14063-126 Circuit Board 34384



1 Control Mounting Plate 268612 Control Box 253363 Time Clock (220 v) 262514 Timer 254765 Toggle Switch Boot 17396 Push Button Boot 207847 Shoulder Nut 134078 Toggle Switch Boot 134069 Fuse Holder 2443110 1 amp, 3 AG Fuse 293511 Contactor 428312 Pipe Plug 24458-213 Inner Box Mounting Plate 2529314 Terminal Block 727015 Toggle Switch 776716 Momentary Switch 578517 Ground Plate 2548318 Toggle Switch 601419 Mounting Adapter 2547820 Mounting Adapter 2548021 Pilot Light 704422 Timer Socket 2547723 Timer Cover 25479


Breeder Control Panel: Part No. 25175



1 #10 External Lock Washer 3052 Fuse Holder 244313 1 Amp Fuse (3 AG) 29354 Contactor 42835 Control Box 275776 Control Panel Mounting Panel267977 Control Mounting Panel 275758 Terminal Block 268629 10-32 Ground Screw 496810 Cup Washer 577511 Pilot Light 704412 Toggle Switch 776713 Toggle Switch Boot 1340614 Shoulder Nut 1340715 Time Clock (230 V) 2679516 Mounting Adapter 2548017 Timer 2547618 Timer Socket 2547719 Mounting Adapter 2547820 Cover 25479


Breeder Feeder Feed-Only Control Panel: Part No. 27440



Meal-Time Control Panel: Part No. 34385


16 Battery Box Assembly 3509517 “AAA” Battery (1.5V) 3458418 Seal 3476719 Strapping 29014-420 Terminal Block 734721 Pilot Light 2970822 Toggle Switch 3438823 Toggle Switch 3457824 MOV 14063-125 Nylon Hex Nut 1/4-20 891626 Circuit Board 3438427 Pilot Light Assembly 3546128 Terminal Mount Bracket 3509429 Terminal Strip 34925-630 Current Monitor 35460


1 Control Box 30860-42 Clear Lid 30859-13 Control Box Latch Pivot 308634 Control Box Latch 308625 Fuse Holder 244316 Control Box Mount Panel 348527 Back Mount Panel 345648 Front Panel 345659 Time Clock Connector 3546410 3 Amp Fuse 2047211 Terminal Mount Bracket 3456312 Terminal Strip (12 position) 3492513 P & B Relay (240 VAC) 3473314 Dual Transform. (115/230V) 3457115 Mount Bracket 34562



Time Clock Control: Part No. 34574


1 Control Box 30860-42 Clear Lid 30859-13 Control Box Latch Pivot 308634 Control Box Latch 308625 Fuse Holder 244316 Control Box Mount Panel 348527 Back Mount Panel 345648 Front Panel 345659 Time Clock Connector 3546710 3 Amp Fuse 2047211 Terminal Mount Bracket 3456312 Terminal Strip (12 position) 3492513 P & B Relay (240 VAC) 34733


14 Dual Transformer (115/230 V)3457115 Mount Bracket 3456216 Battery Box Assembly 3509517 “AAA” Battery (1.5V) 3458418 Seal 3476719 Strapping 29014-420 Terminal Block 727021 Pilot Light 2970822 Toggle Switch 3438823 Toggle Switch 3457824 MOV 14063-125 Nylon Hex Nut 1/4-20 891626 Circuit Board 3438427 Pilot Light Assembly 35461


Electrical Control and Components

Breeder Feeder Control: Part No. 8700A


1 Control Mounting Plate 268612 Contactor 42833 #10 Ext. Lock Washer 3054 10-32 Hex Nut 42975 10-32 Ground Screw 49686 Cup Washer 57757 Inner Box Mounting Plate 252938 Inner Box Mounting Plate 252939 Pipe Plug 24458-210 Terminal Block 727011 10-32 x 3/8” Pan Hd. Screw 4418-412 15/32 Ext. Lock Washer 2467113 Toggle Switch 776714 Momentary Switch 578515 Ground Plate 2548316 Toggle Switch 601417 Control Box 2626918 Mounting Adapter 2548019 Time Clock 3540120 Fuse Holder 2443121 1 Amp Fuse 293522 Toggle Switch Boot 1340623 Shoulder Nut 1340724 Push Button Boot 20784



Meal-Time Control Panel: Part No. 7022A


1 Control Panel Mount. Plate 267972 Control Box 267993 Component Mounting Panel 267984 Contactor 42835 Mounting Track 48296 Current Monitor Circuit Panel72537 8-32 x 5/16” Pan Hd. Screw 8018 10-32 x 1” Pan Hd. Screw 4418-19 Terminal Block 884810 Pipe Plug 24458-211 10-32 Ground Screw 496812 Cup Washer 577513 #10 Ext. Lock Washer 30514 Fuse Holder 2443115 1 Amp Fuse 293516 Pilot Light 704417 Toggle Switch 2013518 15/32 Ext. Lock Washer 2467119 Mounting Adapter 2548020 Time Clock (230 V) 26795


The Time Clock Control (110 V.) may be ordered under Part No. 27250

The Time Clock Control (220 V.) may be ordered under Part No. 26230.

Note: This version of the 26230 Time Clock Control was discontinued on June 15, 1995.

110 V. 220 V.(27250) (26230)


1 Control Box 27131 271312 Contactor 4122 41223 #10 Ext. Lock Washer 305 3054 10-32 Hex Nut 4297 42975 Mounting Plate Support 27132 271326 10-32 Ground Screw 4968 49687 Cup Washer 5775 57758 Toggle Switch 20135 201359 15/32 Ext. Lock Washer 5773 2467110 Mounting Adapter 25480 2548011 Time Clock 27299 2679512 Boot 1739 173913 Pilot Light 7044 2058


Time Clock Control



Time Clock Control

The Time Clock Control (220 V.) may be ordered under Part No. 26230.

Note: This version of the 26230 Time Clock Control was released on June 15, 1995.


1 Clear Box Lid 30859-12 Time Clock Control Decal 2529-2593 Control Box Mount Panel 348524 Control Box 30860-35 208-240 V Contactor 42836 Terminal Block 268627 Toggle Switch 201358 Pilot Light 70449 Front Panel 3611210 Time Clock Assembly 3491211 Control Box Latch Pivot 3086312 Control Box Latch 3086213 Back Panel 36111



Tork Time Clocks

Part Number

Time Period

Timing Motor

TorkModel Number

1977 24 Hour 120 V. 60 Hz. 8001

3710 24 Hour 240 V. 60 Hz. 2-8001 or 8004

3711 24 Hour 240 V. 50 Hz. 2-8001

4719 48 Hour 220 V. 50 Hz. 2-8001-2D or 8005-2D

4816 12 Minute 120 V. 60 Hz. 12M8001

5781 48 Hour 240 V. 60 Hz. 8004-2D

Contactor Control


1 10-32 x 1/2” Binder Hd. M.S.4303-42 Cup Washer 57753 #10 Star Washer 3054 #10-32 Hex Nut 42975 Contactor Housing 41246 #8 Hex Washer Hd. S.M.S. 60547 #8-32 x 5/16” Rd. Hd. M.S. 8018 Contactor (110 V) 4122

Contactor (230 V) 42839 Contactor Cover 4121

The complete 110 V Contactor Control may be ordered under Part No. 4119.

The complete 220 V Contactor Control may be ordered under Part No. 4283.




1 Box and Cover 73682 Mounting Plate Support 242923 #10 Ext. Lock Washer 3054 #10-32 Hex Screw 49685 Cup Washer 57756 Contactor (220 V) 4283

Contactor (110 V0 41227 #10-24 Pan Head Screw 4418-3

The Contactor Box containing (1) 4283 Contactor may be ordered under Part No. 24392-1.

The Contactor Box containing (2) 4283 Contactors may be ordered under Part No. 24392-2.

The Contactor Box containing (1) 4122 Contactor may be ordered under Part No. 24545-1.

The Contactor Box containing (2) 4122 Contactors may be ordered under Part No. 24545-2.

Contactor Control



1 High Differential Shield 249932 Paddle Cover 27083 Paddle 27094 6-32 Hex Nut 7715 SPDT Switch 27026 Frame Weldment 2711

8 Fabric Retainer 27059 Back 270710 Mounting Bracket 270311 Switch Bracket 2499112 Mounting Bracket Assembly 291113 Cover 71114 Handy Box 114515 6-32 x 7/8” Screw 192116 Grommet 2417 Flat Washer 2955-1918 10-32 Crown Lock Nut 696319 Spring 24992


Hopper Level Control: Part No. 2912



1 Gasket 6777 67772 Switch Box Cover 6776 67763 Switch Box 24678 78414 10-32 Hex Nut 4297 - - - -5 #10 Lock Washer 305 - - - -6 Cup Washer 5775 - - - -7 10-32 Stud 7007 - - - -8 Paddle Shield 24059 240599 Switch Brace Bracket 2703 270310 Switch Frame Assembly 14499 1449911 Paddle 14519 1451912 Switch Frame Assembly 14498 1449813 Diaphragm 28157 2815714 High Differential Shield 7808 780815 Switch Bracket 7068 706816 Gasket 6968-1 6968-117 Spring 6972 697218 10-32 Lock Nut 6963 696319 Pin 6775 677520 Switch Insulation 1907-5 1907-521 SPDT Switch 7069 706922 Danger Decal 2527-35 2527-35-- Mounting Bracket Assembly 2911 2911-- 1/2” Liquid Tight Connector 23779 - - - --- 2-Terminal Block - - - - 34925-2


Hopper Level Control: Part No. 14550 & 27761 (International)


Floor Feeder Scale Systems and Components

Weigh Scale Template: Part No. 5798


1 Rear Plate 59842 Side Plate 59883 Beam Box Leg Plate 59864 Connector Plate 59855 Center Plate 59896 Front Plate 5987



Weigh Scale Assembly


1 Lower Main Stand 7A2 Upper Main Stand Assembly 9A3 Left Main Lever Assembly 1AL4 Right Main Lever Assembly 1AR5 Steelyard Rod 256 Trip Loop 157 Transverse Lever Assembly 10A8 Shackle 199 Load Loop 1810 Transverse Stand Assembly 21A

Complete 5,000 Lbs Bin Scale Assembly is Winslow Part No. CT1819.

Complete 8,000 Lbs Bin Scale Assembly is Winslow Part No. CT6514.

The complete Bin Scale Components must be ordered through:Winslow Scale Company25th and Haythorne, P.O. Box 1523Terre Haute, IN 47808Phone: 812/466-5265.



Beam Box Assembly: Part No. 5790


22 3/8-16x3/4 HHCS 218223 Pivot Bracket 580324 3/8-16 Hex Nut 154925 Weigh Beam Assembly See Note Below26 10-24x3/8 Truss Screw 50127 Cover Weldment 579928 Leg Support 592429 Leg Weldment 579330 Channel 758931 Romex Connector 131732 Resistor, 390 ohm 1709-1933 Mounting Cover 6956

Note: The applicable Weigh Beam Assembly must be or-dered through: Winslow Scale Company25th and Haythorne, P.O. Box 1523Terre Haute, IN 47808Phone: 812/466-5265.


1 Case Weldment 57972 Over Center Clamp 25363 10-24 P.M. Nut 1354 10-24 x 3/8" Rd. Hd. M.S. 15535 4-40 Hex Nut 35116 Trig Loop 74727 4-40 x 5/8" Rd. Hd. M.S. 35108 Proximity Sensor 66899 Liquid Tight Connector 1347710 Momentary Switch 578511 Push Button Boot 2078412 Terminal Block 727013 Terminal Box Decal 2529-32614 Switch Box Cover 677615 Switch Mount Bracket 2824716 Water Tight Connector 2377917 Terminal Mount Box 2859718 Gasket 677719 4-40 x 3/4" Rd. Hd. M.S. 4143-220 Magnetic Actuator 578921 Terminal Mount 28599



5000# Weigh Beam Assembly: Part No. 9447*

Description Part No.

Bearing 7Pivot 4Loop Assembly 6Back Balance Assembly 11Pivot 12Poise 10Weigh Beam 15Face Plate 14

*The complete Weigh Beam Assembly must be ordered through: Winslow Scale Company25th and Haythorne, P.O. Box 1523Terre Haute, IN 47808Phone: 812/466-5265.


8000# Weigh Beam Assembly: Part No. 6514*


Weigh Beam 1Main Poise 2Aux. Poise 3Back Balance Assembly 4Loop Assembly 5

*The complete Weigh Beam Assembly must be ordered through: Winslow Scale Company25th and Haythorne, P.O. Box 1523Terre Haute, IN 47808Phone: 812/466-5265.



Model 100 & Model 200 Digital Indicators


Model 200 Indicator w/Computer Interface 30225

Model 200 Indicator w/Pulsed Output 34454

Model 200 Indicator w/Computer Interfaceand Junction Control 30228

Not ShownCable for RS232 Port 30189Power Cable 3017710’ Data Cable 3019420 Milliampere Connector 30187

Model 200 IndicatorModel 100 Indicator


Model 100 Indicator w/Computer Interface 30210

Model 100 Indicator w/Computer Interfaceand Connection Box 30232

Not ShownCable for RS232 Port 30189Power Cable 3017710’ Data Cable 3019420 Milliampere Connector 30187

Connection Box: Part No. 30226



J-Box w/30’ Cord 30201*J-Box w/50’ Cord 30202*J-Box w/70’ Cord 30203*J-Box w/90’ Cord 30204*J-Box Assembly (no Plug) 30182J-Box Assembly 30235

Not ShownJ-Box Extension Plug Kit (Plugs Only) 30192J-Box Extension Cable (Cable only) 30190

*Includes Power Cable and Cord (as specified)Note: J-Box Cables may be ordered separately. See Miscellaneous Components and Cable Sets Parts List on page 80.


J-Boxes & Cable Sets

J-Box Duplex Kit


J-Box Duplex Kit w/30’ Cord 30207J-Box Duplex Kit w/50’ Cord 36752J-Box Duplex Kit w/70’ Cord 36753J-Box Duplex Kit w/90’ Cord 36754



Duplex J-Box


Duplex J-Box w/50’ Cord 36687Duplex J-Box w/70’ Cord 36688Duplex J-Box w/90’ Cord 36689


J-Box Cable (30’) 36690J-Box Cable (50’) 36691J-Box Cable (70’) 36692J-Box Cable (90’) 36693J-Box Extension Kit (Plugs only, no Cable) 30192J-Box Extension Cable (Cable only) 30190J-Box Extension Cable Assembly 30188*Cable for RS232 Port 30189Power Cable 3017710’ Data Cable 3019420 Milliampere Connector 30187“Y” Cable (2 female, 1A male Connector) 37692**

*Includes (1) male and (1) female Cannon Plug**Used with Livestock Scales only

Miscellaneous Components and Cable Sets



Junction Control: Part No. 25784


1 Control Box 290112 Terminal Block Bracket 302333 Grommet 85144 #10-32 x 3/8” Pan Hd. Screw4418-35 Terminal Block 72706 #6-32 x 1/2” Pan Hd. Screw 4402-67 Scale Reset Terminal Decal 2526-3188 Relay Socket 302349 Relay 3023610 #10 External Lock Washer 305


11 #10-32 Ground Screw 496812 Cup Washer 577513 Momentary Switch 578514 Grounding Plate 3023715 Push Button Boot 2078416 Warning Decal 2527-1517 Mounting Plate 3014318 Conduit Lock Washer 335719 Liquid Tight Connector 23779



Junction Control w/Fill Option: Part No. 30240


1 Control Box 302382 Terminal Block Bracket 302333 Grommet 85144 #10-32 x 3/8” Pan Hd. Screw4418-35 Terminal Block 73476 #6-32 x 1/2” Pan Hd. Screw 4402-67 Scale Reset Terminal Decal 2526-3198 Relay Socket 302349 Relay 3023610 #10 External Lock Washer 30511 #10-32 Ground Screw 4968


12 Cup Washer 577513 Momentary Switch 578514 Grounding Plate 3023715 Push Button Boot 2078416 Warning Decal 2527-1517 Mounting Plate 3014318 Toggle Switch 2013519 Relay 2705120 Toggle Switch Boot 173921 Conduit Lock Washer 335722 Liquid Tight Connector 23779



Load Cells and Mount Kits


1 3/4" x 6" Quick Pin - - - - 2 Top Plate - - - - 3 T.C. 35 Load Cell 30221

T.C. 125 Load Cell 302224 5/8" x 5" Quick Pin - - - - 5* Mount Kit for T.C. 35 30216

Mount Kit for T.C. 125 30217

*The Mount Kit does not include the Item #3.


2 Top Plate - - - - 3 T.C. 15 Load Cell 302195* Mount Kit for T.C. 15 30176



2 Top Plate - - - - 3 T.C. 180 Load Cell 30223

T.C. 180 Load Cell w/21’ cord 302245* Mount Kit for T.C. 180 30218


T . C . 3 5 & 1 2 5

T . C . 1 5

T . C . 1 8 0



Load Cells and Mount Kits


1 C.T. 30 Load Cell 350182 C.T. Mount Half - - - -3 M16 x mm Hex Nut - - - -4 M16 Lock Washer - - - -5 Threaded Plate - - - -6 Rubber Shim - - - -7 Pin - - - -8 Cotter Pin - - - -9 M16 x 2 mm x 65 mm Nut - - - -10 Welded Plate - - - -11 Sealing Sponge Ring - - - -

Note: Items 2 - 11 may be ordered as a Mount Kit for C.T. 30 Scale under Part No. 35017.

C . T . 3 0 K

6-Legged Bin Adapter Kit


Beam Assembly 30183

The 6-Legged Bin Adapter Kit, including (2) Beam Assemblies and (1) Beam Assembly Hardware Kit, may be ordered under Part No. 30208.


1 Power Cord (220 V) 306822 Power Supply (220 V) 306833 Power Supply (includ. cord) 302004 Power Supply (110 V) 30206-- Power Cord for Indicator 30177

Scale Systems available (by weight):

5,000 Lbs. 3020912,000 Lbs. 3021148,000 Lbs. (7’ Bins) 3021348,000 Lbs. (9’ Bins) 3021260,000 Lbs. 3021460,000 Lbs. 3458080,000 Lbs. 3457590,000 Lbs. 30215120,000 Lbs. 35020

Note: Scale Systems include the Junction Box (or Duplex Kit), Load Cells and Mounts. The Digital

Power Supply



Livestock Scale Indicators


Model 100 Indicator (2,000 lbs) 34435Model 111 Indicator (907 kg) 34817Model 210 Indicator (2,000 lbs/907 kg) 34581Model 115 Indicator (6,000 lbs) 34436Model 116 Indicator (2,721 kg) 34818Model 215 Indicator (6,000 lbs/2,721 kg) 34582

Notes:Model 100 shown.Mounting Bracket included with Indicator.


2,000 lbs (907 kg) Load Cell (2 req.) 344376,000 lbs (2,721 kg) Load Cell (2 req.) 34438

Livestock Scale Load Cells



Hopper Scales: Part No. 24176


1 Switch Assembly 241712 Counterbalance Weight 241623 Sliding Weight 241634 Beam Assembly 241775 Eyebolt 241756 Weight Washer 2955-30

5# Weight Plate 241647 Master Suspension Cable - - - -8 3/6” Cable Clamp 7329 Cable Plate 2417210 1/8” Cable Clamp 1489811 3/32” Stainless Steel Cable 7130



Hopper Scales Switch Assembly: Part No. 33653


1 Relay Assembly 241742 Terminal Box 336543 Box Cover 67764 Gasket 67775 Danger Decal 2527-256 Momentary Switch 57857 Push Button Boot 207848 1/2” Conduit Locknut 33579 Proximity Switch Assembly 33605

Proximity Switch 6689Liquid Tight Connector 237791/4” Vinyl Tubing 14454-7

10 Liquid Tight Connector 2377911 Switch Mount Assembly 3365512* Scale Bar Guide 3361313 Switch Mount 33615

*Item #12 is a component of Item #11.


1 Box and Cover 146112 Momentary Switch 57853 Toggle Switch 201354 Grounding Plate 146045 Toggle Switch Boot 17396 Push Button Boot 20784

Hopper Scales Switch Box Assembly: Part No. 14613


Floor Feeder Screener Components

WEIGH-MATIC® Model 90 Screener: Part No. 25432

*May be ordered as an assembly under Part No. 25704.

**May be ordered as an assembly under Part No. 25472.

***May be ordered as an assembly under Part No. 27426.

§Junction Box-not shown • See individual parts list on page 89.

The entire WEIGH-MATIC Model 90 Screener including: -25432 Screener (components shown),-4347 upper boot,-9301 lower boot,-6942-25 auger,-6293 10’ auger tubes, -7357 90 degree elbows, -9301 boot assembly, -5790 Beam Box, and -3259-52 power unit

may be ordered under Chore-Time Part No. 25790.


1 Control Unit Head 257202 Seal 48733 Screener Body 254464 Clamp 61835*** Screen 74366*** Extruded Plate 220847*** Anchor Tube 50698*** Screen Retainer 247969 Lid Seal Gasket 592810 Flexible Drop Tube 2570211 Drop Tube 638112 Power Unit 3259-5213* Agitator 2567414* Driver Assembly 2570515** Top Channel 2546916** Corner Support 2547017** Support Channel 2546818** Foot (L.H.) 25467-119** Support Channel Extension 3580020** “U” Bolt 2887421** Foot (R.H.) 25467-2--§ Junction Box Assembly 25694-- Screener Cover 25701



WEIGH-MATIC® Model 90 Screener Control Unit


1* 10-32 Lock Nut 69632* Spring 69723* Gasket 6968-14* Paddle 78965* Pin 67756* Mounting Plate Assembly 79087* Pilot Light Assembly 70448* 1/2" Liquid Tight Fitting 269809* Switch Bracket 706810* SPDT Actuator Switch 711411* Switch Box 25696


12 Drop 609113 Slide 507314 Body Assembly 2426815* Gasket 677716* Switch Box Cover 677617 1/2" Flexible Conduit 26982-918 Water Tight Connector 23810-- Diaphragm Assembly 7900

*These items may be ordered as an assembly under part no. 25697.The complete Control Unit (including Driver Assem-bly and Junction Box Assembly) may be ordered under part no. 25720.


1 Junction Box Mount 256922 Junction Box (including cover)256933 Mounting Panel 256914 Toggle Switch 77675 Toggle Switch Boot 134066 Pilot Light 70447 Terminal Block 88488 10-32 Ground Screw 49689 10 ext. Lock Washer 30510 Cup Washer 5775

Junction Box Assembly: Part No. 25694



WEIGH-MATIC® Model 90 Screener Power Units

Screener Power Units • 50 Hz.


1 Motor- -3/4 HP, 3-Phs, 220/380 V, 28034Motor- -3/4 HP, 1-Phs. 220/380 V, 6305

2 90 Degree Connector 4288 3 Ant i -Shor t Bushing 63044 Pipe Plug 27555 Magnet ic Pipe Plug 301606 "S" Hook 42707 Pin ion Assembly- for 1 HP Motors 50468 Vent Plug 35239 5/16-18x5/8" Hx Hd M S 4412-110 Gearhead Assembly-425 RPM 3261-10

Complete Power Units Part No.

3/4 HP, 348 RPM, 3-Phs, Power Unit 3259-1043/4 HP, 348 RPM, 1-Phs, Power Unit 3259-88


1 Motor- -3/4 HP / 230V. 50512 90 Degree Connector 42283 Ant i -Shor t Bushing 63044 Pipe Plug 27555 Magnet ic Pipe Plug 301606 "S" Hook 42707 Pinion Assembly 50468 Vent Plug 35239 5/16-18x5/8" Hx Hd M S 4412-110 Gearhead Assembly-348 RPM 3261-7

Complete Power Units Part No.

3/4 HP, 348 RPM Power Unit 3259-52

Screener Power Unit • 60 Hz.



Model 90 Bin Fill Cap Kit: Part No. 25806

Model 75 Bin Fill Cap Kit: Part No. 6563

I tem Descript ion Part No.

1 Lid Ass’y 7 6 8 92 Tube Anchor Weldment (Mod. 90) 5 0 6 9

Tube Anchor Weldment (Mod. 75) 6 5 1 83 Over Center Clamp 2 5 3 64 Tube Clamp (Mod. 90) 6721-1

Tube Clamp (Mod. 75) 6515-15 Tube Inser t (Mod. 75 s tee l sys tems) 6 5 2 46 Sponge Tubing 5 9 2 87 Driver Assembly (Mod. 90) 6 8 6 1

Driver Assembly (Mod. 75) 6 8 6 28 Cover Weldment 7690


Floor Feeder Miscellaneous Components

Hens Only Grill (for Pan Breeder Feeder)

Part No. Description Width “A” Height “B” Height “C”

24487 Pan Shield 1.688” (42.86 mm) 2.750” (69.99 mm) 3.300” (83.82 mm)

30244 Pan Shield 1.732” (44.00 mm) 2.750” (69.99 mm) - - - -

30246 Pan Shield 1.811” (46.00 mm) 2.250” (57.15 mm) 2.500” (63.50 mm)

Control Shield: Part No. 24887Program Gauge: Part No. 14251


1 Level Glass 48532 Gauge Clamp Weldment 145233 Pointer Assembly 48524 Indexing Gauge Decal 2529-207

1

2 3

4



Winch Control: Part No. 34812


1 Switch Lock 349842 Toggle Switch (DPDT) 201353 Clear Lid 30859-14 Control Box Latch 308625 Fuse Holder 244316 Relay 55747 4 PDT Relay (230 V) 349108 Terminal Mount Bracket 345639 Back Mount 3438310 Control Box Mount Panel 34852


11 Momentary Switch 578512 Toggle Switch 601413 Pilot Light 704414 Winch Control Panel 3438215 Time Clock 3491216 Track Mounting Socket 3490917 Terminal Strip 3492518 Control Box Latch Pivot 308 6319 10 Amp Fuse 735020 Control Box 34985



Winchable Feed Level Tube Components


1* Crank 148772* Spring Pin 14881-13* Drum 146784* 1/4-20 x 1/2” Bolt 14875* 1/4-20 Locknut 12696* 1/4-20 Jam Nut 208267* Stop 146778* Spring 15439* Ratchet Body 1467510 Cable Assembly 1427811 Tube Clamp12 Spring 2430213 Cable Clamp 1489814 3/16” Pop Rivet 462915 Tube Guide 2411316 Feed Level Tube 1428017 3/32” Galvanized Cable 4973

Optional Stain. Steel Cable 7130

*These items may be ordered as a Feed Tube Winch Assembly under Chore-Time Part No. 14680).


Contact your nearby Chore-Time distributor or representative for additional parts and information.Chore-Time Equipment, A Division of CTB, Inc.

P.O. Box 2000, Milford, Indiana 46542-2000 U.S.A.Printed in the U.S.A.

Phone: 219-658-4101 • E-Mail: [email protected]

Made to work.

Built to last.™

Documents

Floor Feeder Repair Parts Manual - Chore-TimeFloor Feeder Repair Parts Manual Volume II 3 Purpose of the Repair Parts Manual The purpose of the Repair Parts Manuals is to provide the