MV network management - Easergy range Flite 116-SA Technical data sheet Radio fault passage indicator for overhead networks 2008 b Remote monitoring of overhead lines (currents, faults, voltage losses, etc.) b Detects both short-circuits and low current earth faults b Highly visible 360° red flashing light b Easy installation (spring grips) b Remote setting PE41017 Application: fast location of faulty circuits The location of a fault along an overhead MV network by mean of optical fault passage indicators is time-consuming (traffic jam, hard to access network sections, long outgoing feeders). A solution is to use (in addition) our remotely indicated Flite 116-SA fault passage detector. The payback is quick because the outage time being decreased, the reduction of non-distributed energy is important, and the quality is improved. Principal Each of the Flite 116-SA clipped onto the MV line communicates via a low power licence-free radio with a G200 RTU mounted on the pole. The G200 RTU is able to manage the communication with up to 9 Flite 116-SA (3 MV lines) and transmits information to the SCADA using open protocols such as DNP3 or IEC 870-5-101/104. Communication with G200 RTU b Frequency: 918 MHz or others upon local standard, licence-free. Frequency spread spectrum used to avoid radio interferences b Secured protocol: enabling message correction and repetition b Maximum distance: 100m b Capacity: up to 9 Flite 116-SA (the number of Flite 116-SA monitored by G200 affects the autonomy of the Flite 116-SA lithium battery). Fault detection (same characteristics as Flite 110-SA) b Self-adaptation: Flite 116-SA adjusts to the network voltage and frequency b Configuration: Flite 116-SA is remote configured from the G200 at the pole bottom b Fault types: Flite 116-SA detects and transmits earth fault (di/dt algorythm), short circuits and voltage loss b Inrush current filter: when the line is energized, a time delay filters inrush current due to transformers magnetization b Transient faults: Flite 116-SA detects and transmits transient fault (a fault is considered as “transient” when the upstream protection device eliminates the fault during its reclosing cycle) b Fault confirmation: faults are confirmed by the loss of voltage after the upstream protection device has tripped b Reset: permanent fault indication is automatically cleared when voltage returns to the MV line or following a time delay. Operation b Instantaneous MV line fault reporting: v Instantaneous transmission to the G200 RTU of the fault detection (earth or phase to phase) or the voltage drop b Periodic event reporting: v Continuous recording of the current values, updating of RTU local archives (average, min, max) v MV line status v Flite 116-SA battery status b Communication to SCADA: v Data transmission v Remote parameter settings. G200 GF PE41016
MV network management - Easergy rangeFlite 116-SATechnical data
sheetRadio fault passage indicatorfor overhead networks2008b Remote
monitoring of overhead lines (currents, faults, voltage losses,
etc.)b Detects both short-circuits and low current earth faultsb
Highly visible 360 red fashing lightb Easy installation (spring
grips)b Remote settingPE41017Application: fast location of faulty
circuitsThe location of a fault along an overhead MV network by
mean of optical fault passage indicators is time-consuming (traffc
jam, hard to access network sections, long outgoing feeders).A
solution is to use (in addition) our remotely indicated Flite
116-SA fault passage detector. The payback is quick because the
outage time being decreased, the reduction of non-distributed
energy is important, and the quality is improved.PrincipalEach of
the Flite 116-SA clipped onto the MV line communicates via a low
power licence-free radio with a G200 RTU mounted on the pole. The
G200 RTU is able to manage the communication with up to 9 Flite
116-SA (3 MV lines) and transmits information to the SCADA using
open protocols such as DNP3 or IEC 870-5-101/104.Communication with
G200 RTUb Frequency: 918 MHz or others upon local standard,
licence-free. Frequency spread spectrum used to avoid radio
interferencesb Secured protocol: enabling message correction and
repetitionb Maximum distance: 100m b Capacity: up to 9 Flite 116-SA
(the number of Flite 116-SA monitored by G200 affects the autonomy
of the Flite 116-SA lithium battery).Fault detection (same
characteristics as Flite 110-SA)b Self-adaptation: Flite 116-SA
adjusts to the network voltage and frequencyb Confguration: Flite
116-SA is remote confgured from the G200 at the pole bottomb Fault
types: Flite 116-SA detects and transmits earth fault (di/dt
algorythm), short circuits and voltage lossb Inrush current flter:
when the line is energized, a time delay flters inrush current due
to transformers magnetizationb Transient faults: Flite 116-SA
detects and transmits transient fault (a fault is considered as
transient when the upstream protection device eliminates the fault
during its reclosing cycle)b Fault confrmation: faults are confrmed
by the loss of voltage after the upstream protection device has
trippedb Reset: permanent fault indication is automatically cleared
when voltage returns to the MV line or following a time delay.
Operationb Instantaneous MV line fault reporting:v Instantaneous
transmission to the G200 RTU of the fault detection (earth or phase
to phase) or the voltage dropb Periodic event reporting:v
Continuous recording of the current values, updating of RTU local
archives (average, min, max)v MV line statusv Flite 116-SA battery
statusb Communication to SCADA:v Data transmissionv Remote
parameter settings.G200 GFPE41016ENMED305015EN 08-2008As standard,
specifcations and designs change from time to time, please ask for
confrmation of the information given in this publication.Publishing
: Schneider Electric Industries SASProduction : Schneider Electric
Industries SASPrinting : Imprimerie du Pont de Claix/JPF - Made in
FranceThis document has been printed on ecological paperSchneider
Electric Industries SAS89, boulevard Franklin RooseveltF-92505
Rueil-Malmaison CedexTl. : +33 (0)1 41 29 85
00www.schneider-electric.comwww.easergy.comART.806910 Schneider
Electric Industries SAS - All rights reservedPE55564Installation
with SICAME toolInstallation with shotgun hotstickG200 unit with
solar panelPE55844PE55563Flite 116-SA
characteristicsApplicationDistribution network voltage 7 kV to 69
kV ( 8 years with hourly transmissionEnvironmentOperating
temperature 40C to + 70CStorage temperature 40C to + 85CHumidity
< 95%Protection level IP 54 IK 7MechanicalDimensions 130 mm x
130 mmNet weight 540 gWind resistance Up to 150 km per
hourStandardsShort-circuit withstand 25 kA/170 ms (ANSI
495)Vibrations and shocks test IEC 68-2-6 and 68-2-29EMI/EFI
immunity IEC 801-3and FCC Part 15Salt spray and humidity tests IEC
68-2-11 and 68-2-30Description ReferencesFlite 116-SA Flite
116-SAInstallation tool with SICAME adapter 59953Installation tool
with BOWTHORP adapter 5995412 meter telescopic hotstick (20 kV
insulated) 59955
