LTE Radio Access, Rel. RL25TD, Operating Documentation, Issue 02, Documentation Change Delivery 3

Creating TD-LTE Configurations

DN09116085

Issue 02BApproval Date 2013-05-23

Confidential

Nokia Siemens Networks is continually striving to reduce the adverse environmental effects of its products and services. We would like to encourage you as our customers and users to join us in working towards a cleaner, safer environment. Please recycle product packaging and follow the recommendations for power use and proper disposal of our products and their compo-nents.

If you should have questions regarding our Environmental Policy or any of the environmental services we offer, please contact us at Nokia Siemens Networks for any additional information.

2 DN09116085

Creating TD-LTE Configurations

Id:0900d805809c738aConfidential

The information in this document is subject to change without notice and describes only the product defined in the introduction of this documentation. This documentation is intended for the use of Nokia Siemens Networks customers only for the purposes of the agreement under which the document is submitted, and no part of it may be used, reproduced, modified or transmitted in any form or means without the prior written permission of Nokia Siemens Networks. The documentation has been prepared to be used by professional and properly trained personnel, and the customer assumes full responsibility when using it. Nokia Siemens Networks welcomes customer comments as part of the process of continuous development and improvement of the documentation.

The information or statements given in this documentation concerning the suitability, capacity, or performance of the mentioned hardware or software products are given "as is" and all liability arising in connection with such hardware or software products shall be defined conclusively and finally in a separate agreement between Nokia Siemens Networks and the customer. However, Nokia Siemens Networks has made all reasonable efforts to ensure that the instructions contained in the document are adequate and free of material errors and omissions. Nokia Siemens Networks will, if deemed necessary by Nokia Siemens Networks, explain issues which may not be covered by the document.

Nokia Siemens Networks will correct errors in this documentation as soon as possible. IN NO EVENT WILL Nokia Siemens Networks BE LIABLE FOR ERRORS IN THIS DOCUMENTA-TION OR FOR ANY DAMAGES, INCLUDING BUT NOT LIMITED TO SPECIAL, DIRECT, INDI-RECT, INCIDENTAL OR CONSEQUENTIAL OR ANY LOSSES, SUCH AS BUT NOT LIMITED TO LOSS OF PROFIT, REVENUE, BUSINESS INTERRUPTION, BUSINESS OPPORTUNITY OR DATA,THAT MAY ARISE FROM THE USE OF THIS DOCUMENT OR THE INFORMATION IN IT.

This documentation and the product it describes are considered protected by copyrights and other intellectual property rights according to the applicable laws.

The wave logo is a trademark of Nokia Siemens Networks Oy. Nokia is a registered trademark of Nokia Corporation. Siemens is a registered trademark of Siemens AG.

Other product names mentioned in this document may be trademarks of their respective owners, and they are mentioned for identification purposes only.

Copyright Nokia Siemens Networks 2013. All rights reserved

f Important Notice on Product SafetyThis product may present safety risks due to laser, electricity, heat, and other sources of danger.

Only trained and qualified personnel may install, operate, maintain or otherwise handle this product and only after having carefully read the safety information applicable to this product.

The safety information is provided in the Safety Information section in the Legal, Safety and Environmental Information part of this document or documentation set.

The same text in German:

f Wichtiger Hinweis zur Produktsicherheit Von diesem Produkt knnen Gefahren durch Laser, Elektrizitt, Hitzeentwicklung oder andere Gefahrenquellen ausgehen.

Installation, Betrieb, Wartung und sonstige Handhabung des Produktes darf nur durch geschultes und qualifiziertes Personal unter Beachtung der anwendbaren Sicherheits-anforderungen erfolgen.

Die Sicherheitsanforderungen finden Sie unter Sicherheitshinweise im Teil Legal, Safety and Environmental Information dieses Dokuments oder dieses Dokumentations-satzes.

DN09116085 3

Creating TD-LTE Configurations

Id:0900d805809c738aConfidential

Table of contentsThis document has 28 pages.

Summary of changes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

1 Flexi Multiradio BTS modules used in configurations . . . . . . . . . . . . . . . 71.1 Flexi Multiradio BTS System Module . . . . . . . . . . . . . . . . . . . . . . . . . . . . 71.2 Flexi Multiradio BTS RF Modules . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 81.3 Flexi Multiradio BTS Remote Radio Head (RRH) . . . . . . . . . . . . . . . . . . 8

2 TD-LTE configurations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 92.1 FZHA-only configurations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 92.1.1 1 L (BW 10MHz or 20MHz) with beamforming . . . . . . . . . . . . . . . . . . . . 92.1.2 1+1 L (BW 10MHz or 20MHz) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 102.1.3 1+1+1 L (BW 10MHz or 20MHz) with beamforming . . . . . . . . . . . . . . . 112.2 FZNC-only configurations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 122.2.1 1 O (BW 10MHz or 20MHz) with beamforming . . . . . . . . . . . . . . . . . . . 122.2.2 1+1 O (BW 10MHz or 20MHz). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 132.2.3 1+1+1 O (BW 10MHz or 20MHz) with beamforming . . . . . . . . . . . . . . . 142.2.4 1+1+1 M+N (BW 10MHz or 20MHz) . . . . . . . . . . . . . . . . . . . . . . . . . . . 152.2.5 1+1+1+1 A or I (BW 10MHz or 20MHz). . . . . . . . . . . . . . . . . . . . . . . . . 162.2.6 1+1+1+1+1 A or I (BW 10MHz) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 172.2.7 1+1+1+1+1 A or I (BW 20MHz) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 182.2.8 1+1+1+1+1+1 A and I (BW 10MHz) . . . . . . . . . . . . . . . . . . . . . . . . . . . 192.2.9 1+1+1+1+1+1 A or I (BW 20MHz) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 202.3 FZHA and FZNC configurations. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 212.3.1 1 Omni A or I (BW 10MHz or 20MHz) . . . . . . . . . . . . . . . . . . . . . . . . . . 212.3.2 1+1 A or I (BW 10MHz or 20MHz) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 222.3.3 1+1 A or I (BW 10MHz or 20MHz) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 232.3.4 1+1+1 A or I (BW 10MHz or 20MHz) . . . . . . . . . . . . . . . . . . . . . . . . . . . 242.3.5 1+1+1 A or I (BW 10MHz or 20MHz) . . . . . . . . . . . . . . . . . . . . . . . . . . . 252.3.6 1+1+1 A or I (BW 10MHz or 20MHz) . . . . . . . . . . . . . . . . . . . . . . . . . . . 262.4 FZNI configurations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 272.4.1 1 M (BW 10MHz or 20MHz). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 272.4.2 1+1 M (BW 10MHz or 20MHz). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 272.4.3 1+1+1 M (BW 10MHz or 20MHz). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28

4 DN09116085

Creating TD-LTE Configurations

Id:0900d805809c738aConfidential

List of figuresFigure 1 Flexi Multiradio 10 BTS System Module . . . . . . . . . . . . . . . . . . . . . . . . . . 7Figure 2 FZHA RF Module . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8Figure 3 FZNC RF Module . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8Figure 4 FZNI Remote Radio Head . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

DN09116085 5

Creating TD-LTE Configurations Summary of changes

Id:0900d805809c7388Confidential

Summary of changes Changes between document issues are cumulative. Therefore, the latest document issue contains all changes made to previous issues.

Changes between issue 02A (2012-11-11, RL25TD) and issue 02B (2013-05-23, RL25TD).

FZNI layout has been added to Flexi Multiradio BTS modules used in configurations. FZNI configurations have been added.Changes between issue 02 (2012-06-25, RL25TD) and issue 02A (2012-11-11, RL25TD).

FBBA layout has been updated throughout the document. Configuration 1+1+1 A or I (BW 10MHz or 20MHz) using two RF Modules is also

supported by FZNC. Information regarding needed FBBA modules in configuration 1+1+1 O (BW 10MHz

or 20MHz) with beamforming has been corrected.

Changes between issue 01 (2012-03-22, RL15TD) and issue 02 (2012-06-25, RL25TD).

Section Flexi Multiradio BTS modules used in configurations has been updated. Section TD-LTE Configurations has been updated:

RL25TD-specific configurations have been added RL15TD-specific configurations have been removed

Issue 01 (2012-03-22, RL15TD) is the first version of the document.

6 DN09116085

Creating TD-LTE Configurations

Id:0900d805809c7388Confidential

Summary of changes

DN09116085 7

Creating TD-LTE Configurations Flexi Multiradio BTS modules used in configurations

Id:0900d805809c7386Confidential

1 Flexi Multiradio BTS modules used in config-urationsThis section presents the following modules used in configurations:

Flexi Multiradio 10 BTS System Module (FSM) Flexi Multiradio BTS RF ModulesFor information about cabling the modules, see Cabling Flexi Multiradio 10 BTS LTE. Pay attention to the order in which the cables are connected.

1.1 Flexi Multiradio BTS System ModuleFlexi Multiradio 10 BTS System Module (FSMF) is used. The indicated optical interfaces are crucial for configurations.

g Note that: Flexi Baseband Module (FBBA) is optional, but needed in some configurations. In

such cases, the FBBA need is stated.When using only one FBBA, install it in the left-hand side slot and connect it to BB EXT1 port on FSMF core. When using two FBBAs, connect the second one to BB EXT2.

The EIF2/RF/6 interface can be used in two modes: as a transport interface or as a RP3-01 interface. The latter is for creating configurations.

Figure 1 Flexi Multiradio 10 BTS System Module

FBBA

RF/EXT1...3

EIF2/RF/6

RF/EXT

BB EXT1 BB EXT2

BB EXT

RF/EXT

BB EXT

8 DN09116085

Creating TD-LTE Configurations

Id:0900d805809c7386Confidential

Flexi Multiradio BTS modules used in configurations

1.2 Flexi Multiradio BTS RF ModulesFlexi Multiradio BTS RF Modules FZHA and FZNC are used.

Figure 2 FZHA RF Module

Figure 3 FZNC RF Module

g Note: Antenna numbers on the actual FZNC RF Module differ from those on Figure 3 FZNC RF Module. The actual antenna connectors (from left to right) are ANT1 to ANT8, although the FZNC is a six-pipe module. Thus, in the software implementation the connectors are presented in the same way as in the figure.

1.3 Flexi Multiradio BTS Remote Radio Head (RRH)Flexi Multiradio BTS RRHFZNI is used.

Figure 4 FZNI Remote Radio Head

ANT1 ANT2 ANT3 ANT4 ANT5 ANT6 ANT7 ANT8 BF CAL

DC IN

OPT 1 OPT 2 OPT 3 OPT 4 EAC

ANT1 ANT2 ANT3 ANT4 ANT5 ANT6 BF CAL

DC IN

OPT 1 OPT 2 OPT 3 OPT 4 EAC

ANT1 ANT2 ANT3 ANT4

OPT1 OPT2 GPSLMP

EA

C

BF

48V

DC

20A

MA

X

48V

DC

20A

MA

X

DN09116085 9

Creating TD-LTE Configurations TD-LTE configurations

Id:0900d805809c736eConfidential

2 TD-LTE configurations

2.1 FZHA-only configurations

2.1.1 1 L (BW 10MHz or 20MHz) with beamforming

ANT1 ANT2 ANT3 ANT4 ANT5 ANT6 ANT7 ANT8 BF CAL

DC IN

OPT 1 OPT 2 OPT 3 OPT 4 EAC

Sector 1

To antenna

10 DN09116085

Creating TD-LTE Configurations

Id:0900d805809c736eConfidential

TD-LTE configurations

2.1.2 1+1 L (BW 10MHz or 20MHz)This configuration requires one FBBA module.

ANT1 ANT2 ANT3 ANT4 ANT5 ANT6 ANT7 ANT8 BF CAL

DC IN

OPT 1 OPT 2 OPT 3 OPT 4 EAC

Sector 2

ANT1 ANT2 ANT3 ANT4 ANT5 ANT6 ANT7 ANT8 BF CAL

DC IN

OPT 1 OPT 2 OPT 3 OPT 4 EAC

Sector 1

DN09116085 11

Creating TD-LTE Configurations TD-LTE configurations

Id:0900d805809c736eConfidential

2.1.3 1+1+1 L (BW 10MHz or 20MHz) with beamformingThis configuration requires two FBBA modules.

To antenna

ANT1 ANT2 ANT3 ANT4 ANT5 ANT6 ANT7 ANT8 BF CAL

DC IN

OPT 1 OPT 2 OPT 3 OPT 4 EAC

Sector 2

To antenna

ANT1 ANT2 ANT3 ANT4 ANT5 ANT6 ANT7 ANT8 BF CAL

DC IN

OPT 1 OPT 2 OPT 3 OPT 4 EAC

Sector 1

To antenna

ANT1 ANT2 ANT3 ANT4 ANT5 ANT6 ANT7 ANT8 BF CAL

DC IN

OPT 1 OPT 2 OPT 3 OPT 4 EAC

Sector 3

12 DN09116085

Creating TD-LTE Configurations

Id:0900d805809c736eConfidential

TD-LTE configurations

2.2 FZNC-only configurations

2.2.1 1 O (BW 10MHz or 20MHz) with beamforming

ANT1 ANT2 ANT3 ANT4 ANT5 ANT6 BF CAL

DC IN

OPT 1 OPT 2 OPT 3 OPT 4 EAC

Sector 1

To antenna

DN09116085 13

Creating TD-LTE Configurations TD-LTE configurations

Id:0900d805809c736eConfidential

2.2.2 1+1 O (BW 10MHz or 20MHz)

ANT1 ANT2 ANT3 ANT4 ANT5 ANT6 BF CAL

DC IN

OPT 1 OPT 2 OPT 3 OPT 4 EAC

ANT1 ANT2 ANT3 ANT4 ANT5 ANT6 BF CAL

DC IN

OPT 1 OPT 2 OPT 3 OPT 4 EAC

Sector 1

Sector 2

14 DN09116085

Creating TD-LTE Configurations

Id:0900d805809c736eConfidential

TD-LTE configurations

2.2.3 1+1+1 O (BW 10MHz or 20MHz) with beamformingThis configuration requires one FBBA module.

ANT1 ANT2 ANT3 ANT4 ANT5 ANT6 BF CAL

DC IN

OPT 1 OPT 2 OPT 3 OPT 4 EAC

To antenna

ANT1 ANT2 ANT3 ANT4 ANT5 ANT6 BF CAL

DC IN

OPT 1 OPT 2 OPT 3 OPT 4 EAC

To antenna

ANT1 ANT2 ANT3 ANT4 ANT5 ANT6 BF CAL

DC IN

OPT 1 OPT 2 OPT 3 OPT 4 EAC

To antenna

Sector 2

Sector 1

Sector 3

DN09116085 15

Creating TD-LTE Configurations TD-LTE configurations

Id:0900d805809c736eConfidential

2.2.4 1+1+1 M+N (BW 10MHz or 20MHz)This configuration requires one FBBA module.

Sector 3

ANT1 ANT2 ANT3 ANT4 ANT5 ANT6 BF CAL

DC IN

OPT 1 OPT 2 OPT 3 OPT 4 EAC

Sector 1

ANT1 ANT2 ANT3 ANT4 ANT5 ANT6 BF CAL

DC IN

OPT 1 OPT 2 OPT 3 OPT 4 EAC

Sector 2

16 DN09116085

Creating TD-LTE Configurations

Id:0900d805809c736eConfidential

TD-LTE configurations

2.2.5 1+1+1+1 A or I (BW 10MHz or 20MHz)This configuration requires two FBBA modules.

ANT1 ANT2 ANT3 ANT4 ANT5 ANT6 BF CAL

DC IN

OPT 1 OPT 2 OPT 3 OPT 4 EAC

Sector 3

ANT1 ANT2 ANT3 ANT4 ANT5 ANT6 BF CAL

DC IN

OPT 1 OPT 2 OPT 3 OPT 4 EAC

Sector 1 Sector 2

Sector 4

For 10 MHz

For 20 MHz

DN09116085 17

Creating TD-LTE Configurations TD-LTE configurations

Id:0900d805809c736eConfidential

2.2.6 1+1+1+1+1 A or I (BW 10MHz)This configuration requires two FBBA modules.

ANT1 ANT2 ANT3 ANT4 ANT5 ANT6 BF CAL

DC IN

OPT 1 OPT 2 OPT 3 OPT 4 EAC

Sector 4

ANT1 ANT2 ANT3 ANT4 ANT5 ANT6 BF CAL

DC IN

OPT 1 OPT 2 OPT 3 OPT 4 EAC

Sector 1 Sector 2 Sector 3

Sector 5

18 DN09116085

Creating TD-LTE Configurations

Id:0900d805809c736eConfidential

TD-LTE configurations

2.2.7 1+1+1+1+1 A or I (BW 20MHz)This configuration requires two FBBA modules.

ANT1 ANT2 ANT3 ANT4 ANT5 ANT6 BF CAL

DC IN

OPT 1 OPT 2 OPT 3 OPT 4 EAC

Sector 4

ANT1 ANT2 ANT3 ANT4 ANT5 ANT6 BF CAL

DC IN

OPT 1 OPT 2 OPT 3 OPT 4 EAC

Sector 1 Sector 2 Sector 3

Sector 5

DN09116085 19

Creating TD-LTE Configurations TD-LTE configurations

Id:0900d805809c736eConfidential

2.2.8 1+1+1+1+1+1 A and I (BW 10MHz)This configuration requires two FBBA modules.

ANT1 ANT2 ANT3 ANT4 ANT5 ANT6 BF CAL

DC IN

OPT 1 OPT 2 OPT 3 OPT 4 EAC

Sector 4

ANT1 ANT2 ANT3 ANT4 ANT5 ANT6 BF CAL

DC IN

OPT 1 OPT 2 OPT 3 OPT 4 EAC

Sector 1 Sector 2 Sector 3

Sector 5 Sector 6

20 DN09116085

Creating TD-LTE Configurations

Id:0900d805809c736eConfidential

TD-LTE configurations

2.2.9 1+1+1+1+1+1 A or I (BW 20MHz)This configuration requires two FBBA modules.

Sector 4

ANT1 ANT2 ANT3 ANT4 ANT5 ANT6 BF CAL

DC IN

OPT 1 OPT 2 OPT 3 OPT 4 EAC

Sector 5 Sector 6

ANT1 ANT2 ANT3 ANT4 ANT5 ANT6 BF CAL

DC IN

OPT 1 OPT 2 OPT 3 OPT 4 EAC

Sector 1 Sector 2 Sector 3

DN09116085 21

Creating TD-LTE Configurations TD-LTE configurations

Id:0900d805809c736eConfidential

2.3 FZHA and FZNC configurationsThese configurations can be deployed on both FZHA and FZNC modules. Use the respective antenna connectors, that is: ANT1 to ANT6 on both modules.

2.3.1 1 Omni A or I (BW 10MHz or 20MHz)

ANT1 ANT2 ANT3 ANT4 ANT5 ANT6 ANT7 ANT8 BF CAL

DC IN

OPT 1 OPT 2 OPT 3 OPT 4 EAC

Sector 1

22 DN09116085

Creating TD-LTE Configurations

Id:0900d805809c736eConfidential

TD-LTE configurations

2.3.2 1+1 A or I (BW 10MHz or 20MHz)

ANT1 ANT2 ANT3 ANT4 ANT5 ANT6 ANT7 ANT8 BF CAL

DC IN

OPT 1 OPT 2 OPT 3 OPT 4 EAC

Sector 1 Sector 2

DN09116085 23

Creating TD-LTE Configurations TD-LTE configurations

Id:0900d805809c736eConfidential

2.3.3 1+1 A or I (BW 10MHz or 20MHz)

ANT1 ANT2 ANT3 ANT4 ANT5 ANT6 BF CAL

DC IN

OPT 1 OPT 2 OPT 3 OPT 4 EAC

Sector 2

ANT1 ANT2 ANT3 ANT4 ANT5 ANT6 BF CAL

DC IN

OPT 1 OPT 2 OPT 3 OPT 4 EAC

Sector 1

24 DN09116085

Creating TD-LTE Configurations

Id:0900d805809c736eConfidential

TD-LTE configurations

2.3.4 1+1+1 A or I (BW 10MHz or 20MHz)This configuration requires one FBBA module.

ANT1 ANT2 ANT3 ANT4 ANT5 ANT6 ANT7 ANT8 BF CAL

DC IN

OPT 1 OPT 2 OPT 3 OPT 4 EAC

Sector 1 Sector 2 Sector 3

For 20MHz

DN09116085 25

Creating TD-LTE Configurations TD-LTE configurations

Id:0900d805809c736eConfidential

2.3.5 1+1+1 A or I (BW 10MHz or 20MHz)This configuration requires one FBBA module.

ANT1 ANT2 ANT3 ANT4 ANT5 ANT6 ANT7 ANT8 BF CAL

DC IN

OPT 1 OPT 2 OPT 3 OPT 4 EAC

Sector 3

ANT1 ANT2 ANT3 ANT4 ANT5 ANT6 ANT7 ANT8 BF CAL

DC IN

OPT 1 OPT 2 OPT 3 OPT 4 EAC

Sector 1 Sector 2

26 DN09116085

Creating TD-LTE Configurations

Id:0900d805809c736eConfidential

TD-LTE configurations

2.3.6 1+1+1 A or I (BW 10MHz or 20MHz)This configuration requires one FBBA module.

ANT1 ANT2 ANT3 ANT4 ANT5 ANT6 ANT7 ANT8 BF CAL

DC IN

OPT 1 OPT 2 OPT 3 OPT 4 EAC

Sector 3

ANT1 ANT2 ANT3 ANT4 ANT5 ANT6 ANT7 ANT8 BF CAL

DC IN

OPT 1 OPT 2 OPT 3 OPT 4 EAC

Sector 2

ANT1 ANT2 ANT3 ANT4 ANT5 ANT6 ANT7 ANT8 BF CAL

DC IN

OPT 1 OPT 2 OPT 3 OPT 4 EAC

Sector 1

DN09116085 27

Creating TD-LTE Configurations TD-LTE configurations

Id:0900d805809c736eConfidential

2.4 FZNI configurations

2.4.1 1 M (BW 10MHz or 20MHz)

2.4.2 1+1 M (BW 10MHz or 20MHz)

ANT1 ANT2 ANT3 ANT4

OPT1 OPT2 GPSLMP

EA

C

BF

48

VD

C

20

AM

AX

48

VD

C

20

AM

AX

Sector 1

ANT1 ANT2 ANT3 ANT4

OPT1 OPT2 GPSLMP

EA

C

BF

48

VD

C

20

AM

AX

48

VD

C

20

AM

AX

Sector 1

ANT1 ANT2 ANT3 ANT4

OPT1 OPT2 GPSLMP

EA

C

BF

48

VD

C

20

AM

AX

48

VD

C

20

AM

AX

Sector 2

28 DN09116085

Creating TD-LTE Configurations

Id:0900d805809c736eConfidential

TD-LTE configurations

2.4.3 1+1+1 M (BW 10MHz or 20MHz)This configurations requires one FBBA module.

ANT1 ANT2 ANT3 ANT4

OPT1 OPT2 GPSLMP

EA

C

BF

48

VD

C

20

AM

AX

48

VD

C

20

AM

AX

Sector 1

ANT1 ANT2 ANT3 ANT4

OPT1 OPT2 GPSLMP

EA

C

BF

48

VD

C

20

AM

AX

48

VD

C

20

AM

AX

Sector 2

ANT1 ANT2 ANT3 ANT4

OPT1 OPT2 GPSLMP

EA

C

BF

48

VD

C

20

AM

AX

48

VD

C

20

AM

AX

Sector 3

Creating TD-LTE ConfigurationsTable of contentsList of figuresSummary of changes1Flexi Multiradio BTS modules used in configurations1.1Flexi Multiradio BTS System Module1.2Flexi Multiradio BTS RF Modules1.3Flexi Multiradio BTS Remote Radio Head (RRH)

2TD-LTE configurations2.1FZHA-only configurations2.1.11 L (BW 10MHz or 20MHz) with beamforming2.1.21+1 L (BW 10MHz or 20MHz)2.1.31+1+1 L (BW 10MHz or 20MHz) with beamforming

2.2FZNC-only configurations2.2.11 O (BW 10MHz or 20MHz) with beamforming2.2.21+1 O (BW 10MHz or 20MHz)2.2.31+1+1 O (BW 10MHz or 20MHz) with beamforming2.2.41+1+1 M+N (BW 10MHz or 20MHz)2.2.51+1+1+1 A or I (BW 10MHz or 20MHz)2.2.61+1+1+1+1 A or I (BW 10MHz)2.2.71+1+1+1+1 A or I (BW 20MHz)2.2.81+1+1+1+1+1 A and I (BW 10MHz)2.2.91+1+1+1+1+1 A or I (BW 20MHz)

2.3FZHA and FZNC configurations2.3.11 Omni A or I (BW 10MHz or 20MHz)2.3.21+1 A or I (BW 10MHz or 20MHz)2.3.31+1 A or I (BW 10MHz or 20MHz)2.3.41+1+1 A or I (BW 10MHz or 20MHz)2.3.51+1+1 A or I (BW 10MHz or 20MHz)2.3.61+1+1 A or I (BW 10MHz or 20MHz)

2.4FZNI configurations2.4.11 M (BW 10MHz or 20MHz)2.4.21+1 M (BW 10MHz or 20MHz)2.4.31+1+1 M (BW 10MHz or 20MHz)