Upload
putifundi
View
203
Download
14
Tags:
Embed Size (px)
DESCRIPTION
Flexi Transport Module
Citation preview
WCDMA RAN, Rel. RU30, Operating Documentation, Issue 13
Flexi Transport Module Parameters
DN70577885
Issue 03IApproval Date 2012-10-19
Confidential
2 DN70577885Issue 03I
Flexi Transport Module Parameters
Id:0900d805809715d1Confidential
The information in this document is subject to change without notice and describes only the product defined in the introduction of this documentation. This documentation is intended for the use of Nokia Siemens Networks customers only for the purposes of the agreement under which the document is submitted, and no part of it may be used, reproduced, modified or transmitted in any form or means without the prior written permission of Nokia Siemens Networks. The documentation has been prepared to be used by professional and properly trained personnel, and the customer assumes full responsibility when using it. Nokia Siemens Networks welcomes customer comments as part of the process of continuous development and improvement of the documentation.
The information or statements given in this documentation concerning the suitability, capacity, or performance of the mentioned hardware or software products are given "as is" and all liability arising in connection with such hardware or software products shall be defined conclusively and finally in a separate agreement between Nokia Siemens Networks and the customer. However, Nokia Siemens Networks has made all reasonable efforts to ensure that the instructions contained in the document are adequate and free of material errors and omissions. Nokia Siemens Networks will, if deemed necessary by Nokia Siemens Networks, explain issues which may not be covered by the document.
Nokia Siemens Networks will correct errors in this documentation as soon as possible. IN NO EVENT WILL Nokia Siemens Networks BE LIABLE FOR ERRORS IN THIS DOCUMENTA-TION OR FOR ANY DAMAGES, INCLUDING BUT NOT LIMITED TO SPECIAL, DIRECT, INDI-RECT, INCIDENTAL OR CONSEQUENTIAL OR ANY LOSSES, SUCH AS BUT NOT LIMITED TO LOSS OF PROFIT, REVENUE, BUSINESS INTERRUPTION, BUSINESS OPPORTUNITY OR DATA,THAT MAY ARISE FROM THE USE OF THIS DOCUMENT OR THE INFORMATION IN IT.
This documentation and the product it describes are considered protected by copyrights and other intellectual property rights according to the applicable laws.
The wave logo is a trademark of Nokia Siemens Networks Oy. Nokia is a registered trademark of Nokia Corporation. Siemens is a registered trademark of Siemens AG.
Other product names mentioned in this document may be trademarks of their respective owners, and they are mentioned for identification purposes only.
Copyright © Nokia Siemens Networks 2012. All rights reserved
f Important Notice on Product SafetyThis product may present safety risks due to laser, electricity, heat, and other sources of danger.
Only trained and qualified personnel may install, operate, maintain or otherwise handle this product and only after having carefully read the safety information applicable to this product.
The safety information is provided in the Safety Information section in the “Legal, Safety and Environmental Information” part of this document or documentation set.
The same text in German:
f Wichtiger Hinweis zur Produktsicherheit Von diesem Produkt können Gefahren durch Laser, Elektrizität, Hitzeentwicklung oder andere Gefahrenquellen ausgehen.
Installation, Betrieb, Wartung und sonstige Handhabung des Produktes darf nur durch geschultes und qualifiziertes Personal unter Beachtung der anwendbaren Sicherheits-anforderungen erfolgen.
Die Sicherheitsanforderungen finden Sie unter „Sicherheitshinweise“ im Teil „Legal, Safety and Environmental Information“ dieses Dokuments oder dieses Dokumentations-satzes.
DN70577885 3
Flexi Transport Module Parameters
Id:0900d805809715d1Confidential
Table of contentsThis document has 487 pages.
Summary of changes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
1 Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 67
2 A2NE Parameters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 682.1 aal2NodeId (AAL2 Node Identifier) . . . . . . . . . . . . . . . . . . . . . . . . . . . . 68
3 A2ST Parameters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 693.1 AAL2EndAddress (AAL2 End Address). . . . . . . . . . . . . . . . . . . . . . . . . 693.2 VCI (Virtual Channel Identifier) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 693.3 VPI (Virtual Path Identifier) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 703.4 aal2sigTTPId (AAL2 Signalling Link Identifier). . . . . . . . . . . . . . . . . . . . 713.5 interfaceNumber (Interface Number) . . . . . . . . . . . . . . . . . . . . . . . . . . . 723.6 stcAlarmEnable (Signalling Transport Converter Alarm Enable) . . . . . . 733.7 unitNumber (Unit Number). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 74
4 A2UT Parameters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 764.1 VCI (Virtual Channel Identifier) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 764.2 VPI (Virtual Path Identifier) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 764.3 aal2pathTTPId (AAL2 User Path Identifier) . . . . . . . . . . . . . . . . . . . . . . 774.4 interfaceNumber (Interface Number) . . . . . . . . . . . . . . . . . . . . . . . . . . . 794.5 pid (Path Identifier) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 794.6 queue2Weight (Weight of AAL2 user path queue Q2). . . . . . . . . . . . . . 804.7 queue3Weight (Weight of AAL2 user path queue Q3). . . . . . . . . . . . . . 814.8 queue4Weight (Weight of AAL2 user path queue Q4). . . . . . . . . . . . . . 824.9 unitNumber (Unit Number). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 83
5 ACCP Parameters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 845.1 atmAccessProfileId (ATM Access Profile Identifier). . . . . . . . . . . . . . . . 845.2 egressBandwidth (Egress Bandwidth) . . . . . . . . . . . . . . . . . . . . . . . . . . 845.3 ingressBandwidth (Ingress Bandwidth) . . . . . . . . . . . . . . . . . . . . . . . . . 86
6 AMGR Parameters. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 886.1 amgrId (Account Manager Identifier) . . . . . . . . . . . . . . . . . . . . . . . . . . . 886.2 ldapConnectionType (LDAP Server TLS access mode) . . . . . . . . . . . . 886.3 primaryLdapPort (Port Number of Primary LDAP Server) . . . . . . . . . . . 896.4 primaryLdapServer (IP address of Primary LDAP Server) . . . . . . . . . . 90
7 ANBA Parameters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 927.1 VCI (Virtual Channel Identifier) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 927.2 VPI (Virtual Path Identifier) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 927.3 interfaceNumber (Interface Identifier) . . . . . . . . . . . . . . . . . . . . . . . . . . 937.4 nbapTTPId (Upper Layer Path Identifier). . . . . . . . . . . . . . . . . . . . . . . . 947.5 nbapType (Upper Layer Connection Type) . . . . . . . . . . . . . . . . . . . . . . 967.6 unitNumber (Unit Number). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 97
8 BFD Parameters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 998.1 bfdActivation (BFD session activation flag) . . . . . . . . . . . . . . . . . . . . . . 99
4 DN70577885
Flexi Transport Module Parameters
Id:0900d805809715d1Confidential
8.2 bfdAdminUp (BFD session admin down state control) . . . . . . . . . . . . . 1008.3 bfdDestAddress (Destination IP address for the BFD session) . . . . . . 1018.4 bfdDetectMult (BFD session packets lost detection time multiplier) . . . 1028.5 bfdGrp (BFD group reference) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1038.6 bfdId (BFD session identifier) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1048.7 bfdSourceIpAddr (Source IP address for the BFD session) . . . . . . . . . 1048.8 bfdSourceUdpPort (UDP source port of the BFD session) . . . . . . . . . . 1058.9 bfdType (BFD session type) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1068.10 desMinTxInt (Desired minimum BFD control word transmit interval) . . 1078.11 function (BFD session function definition). . . . . . . . . . . . . . . . . . . . . . . 1088.12 reqMinRxInt (Required minimum BFD control word receive interval) . . 110
9 BFDGRP Parameters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1119.1 bfdGrpId (BFD Group Identifier ). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 111
10 CCFA Parameters. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11210.1 atmFabricId (ATM Fabric Identifier) . . . . . . . . . . . . . . . . . . . . . . . . . . . 11210.2 ubrPlusEnabled (UBR+ Enabled) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11310.3 vccBundleEnabled (VCC Bundle Enabling Flag) . . . . . . . . . . . . . . . . . 114
11 CERTH Parameters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11511.1 btsCertificateUpdateTime (BTS certificate update time). . . . . . . . . . . . 11511.2 caCertificateUpdateTime (CA certificate update time) . . . . . . . . . . . . . 11511.3 caSubjectName (CMP server subject name) . . . . . . . . . . . . . . . . . . . . 11611.4 certhId (Certification Handler Identifier) . . . . . . . . . . . . . . . . . . . . . . . . 11711.5 cmpServerIpAddress (CMP Server IP Address) . . . . . . . . . . . . . . . . . . 11811.6 cmpServerPort (CMP Server Port) . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11911.7 crServerIpAddress (CR Server IP Address) . . . . . . . . . . . . . . . . . . . . . 11911.8 crServerPort (CR Server Port) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12011.9 crlUpdatePeriod (Certificate Revocation List update period) . . . . . . . . 121
12 CESIF Parameters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12312.1 cesMinUDPPort (CES over PSN source port value range) . . . . . . . . . 12312.2 cesifId (CES over PSN interface identifier) . . . . . . . . . . . . . . . . . . . . . . 124
13 CESPW Parameters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12513.1 administrativeState (Administrative state). . . . . . . . . . . . . . . . . . . . . . . 12513.2 cesPWid (CES over PSN Pseudowire Identifier) . . . . . . . . . . . . . . . . . 12613.3 dscp (DSCP value) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12713.4 framesNumber (Number of frames per CESoPSN packet) . . . . . . . . . 12713.5 jitterBufferSize (Jitter Buffer Size) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12813.6 payloadTimeslots (Payload timeslots of TDM frame) . . . . . . . . . . . . . . 12913.7 remoteUDPPort (Remote UDP port number for CES over PSN) . . . . . 132
14 CESPWT Parameters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13414.1 cesPWTid (CES over PSN pseudowire tunnel identifier) . . . . . . . . . . . 13414.2 destIpAddress (Destination IP address) . . . . . . . . . . . . . . . . . . . . . . . . 134
15 ETHLK Parameters. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13615.1 acceptableFrameTypes (Switch Port Acceptable Frame Types) . . . . . 13615.2 administrativeState (Administrative State) . . . . . . . . . . . . . . . . . . . . . . 137
DN70577885 5
Flexi Transport Module Parameters
Id:0900d805809715d1Confidential
15.3 ethLinkId (Ethernet Link Identifier) . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13715.4 flushFdbOnLos (Flush fdb on LOS mode) . . . . . . . . . . . . . . . . . . . . . . 14115.5 l2BurstSize (Switch Port egress Shaper Burst Size) . . . . . . . . . . . . . . 14215.6 l2IngressRate (Switch Port ingress RateLimiter Rate ) . . . . . . . . . . . . 14315.7 l2ShaperRate (Switch Port egress Shaper Rate) . . . . . . . . . . . . . . . . 14615.8 l2VlanIdList (Switch Port VLAN Member List) . . . . . . . . . . . . . . . . . . . 15015.9 highValue (Switch Port VLAN Member Range High Value). . . . . . . . . 15115.10 lowValue (Switch Port VLAN Member Range Low Value). . . . . . . . . . 15215.11 linkOAMEnabled (Link OAM enabling flag) . . . . . . . . . . . . . . . . . . . . . 15315.12 linkOAMProfile (Link OAM profile reference) . . . . . . . . . . . . . . . . . . . . 15415.13 macAddr (MAC address) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15515.14 portDefaultPriority (Switch Port Default VLAN Priority) . . . . . . . . . . . . 15515.15 portDefaultVlanId (Switch Port Default VLAN Identifier) . . . . . . . . . . . 15615.16 speedAndDuplex (Speed and Duplex flag) . . . . . . . . . . . . . . . . . . . . . 15715.17 synchEMode (Synchronous ethernet mode) . . . . . . . . . . . . . . . . . . . . 159
16 FRLI Parameters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16016.1 afrLinkInterfaceId (Fractional Interface Identifier) . . . . . . . . . . . . . . . . 16016.2 afrTimeSlotSequence (ATM over Fractional JT1 Time Slot Sequence) 16116.3 interfaceNumber (Interface Identifier) . . . . . . . . . . . . . . . . . . . . . . . . . 16316.4 unitNumber (Unit Number). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 164
17 FTM Parameters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16517.1 adaptationVersionMajor (Adaptation Version Major) . . . . . . . . . . . . . . 16517.2 ftmId (BTS Transport Identifier) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16517.3 locationName (Location Name) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16617.4 softwareReleaseVersion (Software Release Version) . . . . . . . . . . . . . 16717.5 systemTitle (System Title) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16817.6 userLabel (User Label) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 169
18 IAIF Parameters. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17018.1 VCI (Virtual Channel Identifier) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17018.2 VPI (Virtual Path Identifier) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17018.3 atmIfNetId (ATM IP Net Interface Identifier). . . . . . . . . . . . . . . . . . . . . 17118.4 destIpAddr (Destination IP Address) . . . . . . . . . . . . . . . . . . . . . . . . . . 17318.5 interfaceNumber (Interface Number) . . . . . . . . . . . . . . . . . . . . . . . . . . 17418.6 unitNumber (Unit Number). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 175
19 IEIF Parameters. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17619.1 cir (Committed information rate) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17619.2 confCost (OSPF configured interface cost) . . . . . . . . . . . . . . . . . . . . . 17719.3 helloInterval (OSPF keepalive message transmission interval). . . . . . 17819.4 ieifId (Identifier of the plain Ethernet interface) . . . . . . . . . . . . . . . . . . 17919.5 interfaceArea (OSPF interface area) . . . . . . . . . . . . . . . . . . . . . . . . . . 18019.6 ipAddr (IP Address Info in the Transport Network) . . . . . . . . . . . . . . . 18119.7 localIpAddr (Local Address of the IP Interface) . . . . . . . . . . . . . . . . . . 18219.8 netmask (IP Network Mask). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18219.9 mtu (Maximum transfer unit) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18319.10 mtuMismatchDetection (MTU mismatch detection in use). . . . . . . . . . 184
6 DN70577885
Flexi Transport Module Parameters
Id:0900d805809715d1Confidential
19.11 ospfWithBfd (OSPF uses additionally BFD) . . . . . . . . . . . . . . . . . . . . . 18519.12 proxyArpIpAddrList (List of proxy ARP IP addresses for this interface.). . .
18619.13 qosEnabled (QOS traffic priorisation enabling flag) . . . . . . . . . . . . . . . 18619.14 retransInterval (OSPF LSA retransmission interval) . . . . . . . . . . . . . . . 18819.15 routerDeadInterval (OSPF router read interval) . . . . . . . . . . . . . . . . . . 18819.16 sbs (Shaper burst size) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18919.17 sbsTotal (Total shaper burst size). . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19019.18 shapedBandwidth (Shaped Bandwidth) . . . . . . . . . . . . . . . . . . . . . . . . 19119.19 sir (Shaper information rate) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19319.20 sirTotal (Total shaper information rate). . . . . . . . . . . . . . . . . . . . . . . . . 19419.21 trafficPathShapingEnable (Traffic path shaping enabling flag) . . . . . . . 19519.22 transmitDelay (OSPF packet transmission delay) . . . . . . . . . . . . . . . . 19619.23 upperLayerShaping (Upper Layer Shaping Enabled Flag) . . . . . . . . . . 19719.24 vlanEnabled (Vlan Enabled flag). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19819.25 vlanId (Vlan ID) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 198
20 IHCP Parameters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20020.1 client_identifier (Entry set for DHCP clients identified by a system name) .
20020.2 dhcpClientIdentifier (DHCP Client Identifier). . . . . . . . . . . . . . . . . . . . . 20020.3 dhcpFixedIpAddress (DHCP Fixed IP Address) . . . . . . . . . . . . . . . . . . 20120.4 dhcpAccessId (DHCP Server Identifier) . . . . . . . . . . . . . . . . . . . . . . . . 20220.5 hardware_identifier (Entry set of DHCP clients identified by a MAC ad-
dress) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20320.6 dhcpFixedIpAddress (DHCP Fixed IP Address) . . . . . . . . . . . . . . . . . . 20420.7 dhcpHardwareIdentifier (DHCP Hardware Identifier) . . . . . . . . . . . . . . 20520.8 range_identifier (DHCP server IP address pool). . . . . . . . . . . . . . . . . . 20620.9 dhcpRangeEnd (DHCP Range End IP Address) . . . . . . . . . . . . . . . . . 20620.10 dhcpRangeStart (DHCP Range Start IP Address) . . . . . . . . . . . . . . . . 207
21 IMAG Parameters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20921.1 administrativeState (Administrative State) . . . . . . . . . . . . . . . . . . . . . . 20921.2 imaGroupId (IMA group identifier). . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21021.3 imaVersionId (IMA Version Identifier) . . . . . . . . . . . . . . . . . . . . . . . . . . 21121.4 interfaceNumber (Interface Number) . . . . . . . . . . . . . . . . . . . . . . . . . . 21221.5 interfaces (Physical interface list) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21221.6 minNumLinks (Minimum Number of Links) . . . . . . . . . . . . . . . . . . . . . . 21321.7 unitNumber (Unit Number) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 214
22 INTP Parameters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21622.1 ntpAccessId (NTP Identifier) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21622.2 ntpServers (List of NTP Server IP Addresses) . . . . . . . . . . . . . . . . . . . 216
23 IPNO Parameters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21823.1 bfdHoldUpTime (BFD throttle time for re-installing protection routes) . 21823.2 btsId (BTS Identifier) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21923.3 btsIpAddr (Base Station IP Address) . . . . . . . . . . . . . . . . . . . . . . . . . . 21923.4 cPlaneIpAddress (Control-plane application IP address) . . . . . . . . . . . 22023.5 cesopsnIpAddress (CES over PSN application IP address) . . . . . . . . . 222
DN70577885 7
Flexi Transport Module Parameters
Id:0900d805809715d1Confidential
23.6 disableFtp (Disable FTP server) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22323.7 flexBusIpAddr (Public IP Address of Flexbus Part of BTS) . . . . . . . . . 22423.8 fpLocalUdpPort (Local UDP port for small packets multiplexing) . . . . 22423.9 fpMuxAmount (Maximum amount of small packets that can be multiplexed)
22523.10 fpMuxDelay (Small packets multiplexing delay time). . . . . . . . . . . . . . 22623.11 fpRemoteUdpPort (Remote UDP port for small packets multiplexing) 22723.12 ftmIpAddr (Flexi Transport Module IP Address). . . . . . . . . . . . . . . . . . 22823.13 ftmNetmask (Netmask of the public IP address) . . . . . . . . . . . . . . . . . 22923.14 iHSPAAdapterCommissioningParameter (I-HSPA adapter initial commis-
sioning parameters) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23023.15 iHSPAmode (I-HSPA mode activation flag) . . . . . . . . . . . . . . . . . . . . . 23123.16 icmpResponseEnabled (Enable response to ICMP traffic) . . . . . . . . . 23123.17 ipNodeId (IP Node Identifier) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23223.18 linkOAMLoopbackSupport (Link OAM remote loopback discovery enabling
flag) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23323.19 mPlaneIpAddress (Management -plane application IP address). . . . . 23423.20 mtu (Maximum transfer unit of the BTS) . . . . . . . . . . . . . . . . . . . . . . . 23523.21 oamCir (Committed information rate for Service OAM messages) . . . 23623.22 oamTlvReply (Optional TLV message reply flag) . . . . . . . . . . . . . . . . 23723.23 omsTls (TLS usage towards the O&M system) . . . . . . . . . . . . . . . . . . 23823.24 ret1IpAddr (RET IP Address) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23923.25 rncIpAddr (RNC IP Address) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24023.26 sPlaneIpAddress (Synchronization-plane application IP address) . . . 24123.27 transportMode (BTS transport mode) . . . . . . . . . . . . . . . . . . . . . . . . . 24223.28 twampMessageRate (TWAMP initiator rate for sending messages) . . 24323.29 twampReflectorOn (TWAMP message response enabling flag) . . . . . 24423.30 twampReflectorPort (TWAMP reflector port number) . . . . . . . . . . . . . 24523.31 twampSourcePort (TWAMP source port number) . . . . . . . . . . . . . . . . 24623.32 uPlane2IpAddress (Second user-plane application IP address) . . . . . 24723.33 uPlane2IpInterface (Second user-plane application IP network interface)
24823.34 uPlaneIpAddress (User plane application IP address) . . . . . . . . . . . . 25023.35 uPlaneIpInterface (User-plane application IP network interface). . . . . 251
24 IPRM Parameters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25424.1 RmExceptions (Restricted Mode Exception) . . . . . . . . . . . . . . . . . . . . 25424.2 sourceTwoDiscr (How is source two defined?) . . . . . . . . . . . . . . . . . . 25524.3 sourceTwoIpAddr (IP address for source two). . . . . . . . . . . . . . . . . . . 25624.4 sourceTwoNetMask (IP Subnet Mask) . . . . . . . . . . . . . . . . . . . . . . . . 25724.5 userLabel (User Label) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25824.6 iprmId (IP Restricted Mode Identifier) . . . . . . . . . . . . . . . . . . . . . . . . . 259
25 IPRT Parameters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26025.1 ipRoutingTableId (IP Routing Table Identifier). . . . . . . . . . . . . . . . . . . 26025.2 staticRoutes (List of static routes) . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26125.3 bfdId (BFD route protection session identifier). . . . . . . . . . . . . . . . . . . 26225.4 destIpAddr (Route destination IP address) . . . . . . . . . . . . . . . . . . . . . 26225.5 gateway (IP address of the next hop of the route) . . . . . . . . . . . . . . . . 263
8 DN70577885
Flexi Transport Module Parameters
Id:0900d805809715d1Confidential
25.6 netmask (Netmask of the destination IP address) . . . . . . . . . . . . . . . . 26425.7 preference (Preference value for the route) . . . . . . . . . . . . . . . . . . . . . 265
26 IVIF Parameters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26726.1 cESoPSN (CES over PSN flag) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26726.2 cir (Committed information rate) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26826.3 confCost (OSPF configured interface cost) . . . . . . . . . . . . . . . . . . . . . 26926.4 helloInterval (OSPF keepalive message transmission interval) . . . . . . 26926.5 interfaceArea (OSPF interface area) . . . . . . . . . . . . . . . . . . . . . . . . . . 27026.6 localIpAddr (Local Address of the IP Interface) . . . . . . . . . . . . . . . . . . 27126.7 mtuMismatchDetection (MTU mismatch detection in use) . . . . . . . . . . 27226.8 netmask (IP network mask of the local IP address) . . . . . . . . . . . . . . . 27326.9 ospfWithBfd (OSPF uses additionally BFD) . . . . . . . . . . . . . . . . . . . . . 27326.10 proxyArpIpAddrList (List of proxy ARP IP addresses for this interface.). . .
27426.11 qosEnabled (QOS traffic priorisation enabling flag) . . . . . . . . . . . . . . . 27526.12 retransInterval (OSPF LSA retransmission interval) . . . . . . . . . . . . . . . 27626.13 routerDeadInterval (OSPF router read interval) . . . . . . . . . . . . . . . . . . 27726.14 sbs (Shaper burst size) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27826.15 sir (Shaper information rate) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27926.16 transmitDelay (OSPF packet transmission delay) . . . . . . . . . . . . . . . . 28026.17 vlanId (VLAN identifier) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28126.18 vlanIfNetId (VLAN interface object identifier) . . . . . . . . . . . . . . . . . . . . 282
27 L2SWI Parameters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28327.1 dscpMap (DSCP to priority queue map) . . . . . . . . . . . . . . . . . . . . . . . . 28327.2 dscp (DSCP value) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28427.3 priorityQueue (Priority queue identifier) . . . . . . . . . . . . . . . . . . . . . . . . 28527.4 enableLayer2Switching (Ethernet Switch Enable) . . . . . . . . . . . . . . . . 28627.5 l2PriorityQueueWeight2 (Layer 2 switch member weight for priority queue
2). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28727.6 l2PriorityQueueWeight3 (Layer 2 switch member weight for priority queue
3). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28727.7 l2PriorityQueueWeight4 (Layer 2 switch member weight for priority queue
4). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28827.8 l2PriorityQueueWeight5 (Layer 2 switch member weight for priority queue
5). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28927.9 l2PriorityQueueWeight6 (Layer 2 switch member weight for priority queue
6). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29027.10 portDefaultPriority (Switch Port Default VLAN Priority (internal Port)) . 29127.11 portDefaultVlanId (Switch Port Default VLAN Identifier (internal Port)) 29227.12 priorityQueueNonIP (Priority queue for non-IP frames) . . . . . . . . . . . . 29327.13 priorityQueuePcp0 (Priority queue for ethernet frames with VLAN PCP bits
0). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29427.14 priorityQueuePcp1 (Priority queue for ethernet frames with VLAN PCP bits
1). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29527.15 priorityQueuePcp2 (Priority queue for ethernet frames with VLAN PCP bits
2). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29627.16 priorityQueuePcp3 (Priority queue for ethernet frames with VLAN PCP bits
3). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 297
DN70577885 9
Flexi Transport Module Parameters
Id:0900d805809715d1Confidential
27.17 priorityQueuePcp4 (Priority queue for ethernet frames with VLAN PCP bits 4) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 298
27.18 priorityQueuePcp5 (Priority queue for ethernet frames with VLAN PCP bits 5) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 299
27.19 priorityQueuePcp6 (Priority queue for ethernet frames with VLAN PCP bits 6) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 300
27.20 priorityQueuePcp7 (Priority queue for ethernet frames with VLAN PCP bits 7) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 301
27.21 priorityQueueUntagged (Priority queue for untagged ethernet frames) 30227.22 qosClassification (QoS Classification Mode) . . . . . . . . . . . . . . . . . . . . 30327.23 switchId (Layer 2 Switch Object Identifier). . . . . . . . . . . . . . . . . . . . . . 30427.24 vlanAwareSwitch (VLAN Aware Switching Enable) . . . . . . . . . . . . . . . 305
28 OAMMA Parameters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30728.1 assocId (Maintenance association identifier) . . . . . . . . . . . . . . . . . . . . 30728.2 maName (Name of the maintenance domain) . . . . . . . . . . . . . . . . . . . 30728.3 vlanId (VLAN identifier of the maintenance association) . . . . . . . . . . . 308
29 OAMMD Parameters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31029.1 domainId (Maintenance domain identifier). . . . . . . . . . . . . . . . . . . . . . 31029.2 mdLevel (Level of the maintenance domain) . . . . . . . . . . . . . . . . . . . . 31029.3 mdName (Name of the maintenance domain) . . . . . . . . . . . . . . . . . . . 311
30 OAMMEP Parameters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31330.1 aisEnabled (AIS message transmission enabling flag) . . . . . . . . . . . . 31330.2 aisTxPeriod (AIS messages transmission period) . . . . . . . . . . . . . . . . 31330.3 ccmTxPeriod (Continuity Check Messages transmission period) . . . . 31430.4 enableCcm (Allow sending of CCM messages and reset CCM counters).
31530.5 ethernetPort (Ethernet link reference) . . . . . . . . . . . . . . . . . . . . . . . . . 31630.6 oammepId (Maintenance association endpoint identifier) . . . . . . . . . . 31730.7 remoteMepList (Remote maintenance association endpoints list). . . . 31830.8 macAddr (MAC address of the remote MEP) . . . . . . . . . . . . . . . . . . . 31930.9 mepId (Remote maintenance association endpoint identifier) . . . . . . . 32030.10 vlanPrio (VLAN PCP bits) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 320
31 OAMPRF Parameters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32231.1 activeMode (Link OAM operational mode at local peer) . . . . . . . . . . . 32231.2 alarmClearanceDelay (Link OAM Link Critical Event Alarm clearance de-
lay) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32331.3 efEventThreshold (Errored Frame Event counting threshold) . . . . . . . 32331.4 efEventWindow (Errored Frame Event counting interval) . . . . . . . . . . 32431.5 efpEventThreshold (Errored Frame Period Event counting threshold) 32531.6 efpEventWindow (Errored Frame Period Event counting interval) . . . 32631.7 efssEventThreshold (Errored Frame Seconds Summary Event counting
threshold) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32731.8 efssEventWindow (Errored Frame Seconds Summary Event counting in-
terval) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32831.9 eventRepetition (OAM PDU message transmission rate) . . . . . . . . . . 32931.10 eventSupport (Link OAM event support flag). . . . . . . . . . . . . . . . . . . . 33031.11 linkLostTime (Link OAM link lost time). . . . . . . . . . . . . . . . . . . . . . . . . 331
10 DN70577885
Flexi Transport Module Parameters
Id:0900d805809715d1Confidential
31.12 linkOAMProfileName (Link OAM Profile Name) . . . . . . . . . . . . . . . . . . 33231.13 loopBackTime (Link OAM loopback duration). . . . . . . . . . . . . . . . . . . . 33331.14 profileId (Profile instance identifier). . . . . . . . . . . . . . . . . . . . . . . . . . . . 33431.15 testFrameRate (Link OAM loopback test message rate) . . . . . . . . . . . 33531.16 testFrameSize (Link OAM loopback test message frame size) . . . . . . 336
32 OSPFV2 Parameters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33732.1 confPref (OSPF routing preference value) . . . . . . . . . . . . . . . . . . . . . . 33732.2 ospfAreas (OSPF area list) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33732.3 areaId (OSPF area identifier) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33832.4 areaStub (OSPF area stub flag) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33932.5 ospfEnabled (OSPF enabling flag) . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34032.6 ospfRouterId (OSPF router identification) . . . . . . . . . . . . . . . . . . . . . . . 34132.7 ospfV2Id (OSPF configuration identifier) . . . . . . . . . . . . . . . . . . . . . . . 34232.8 refBandwidth (Reference bandwidth for OSPF cost equal to 1) . . . . . . 34332.9 spfDelay (OSPF Shortest Path First recalculation delay) . . . . . . . . . . . 34332.10 spfHoldTime (OSPF Shortest Path First hold time) . . . . . . . . . . . . . . . 34432.11 spfMaxHoldTime (OSPF maximum Shortest Path First hold time). . . . 345
33 P3LP Parameters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34733.1 acFieldCompressionOn (Access Control Field Compression flag) . . . . 34733.2 fcsFieldLength (Frame Check Sequence field size) . . . . . . . . . . . . . . 34733.3 magicNumberOn (Magic number flag) . . . . . . . . . . . . . . . . . . . . . . . . . 34833.4 mruSize (Maximum Receive Unit (MRU) size) . . . . . . . . . . . . . . . . . . . 34933.5 p3lpId (PPP link identifier). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35133.6 protocolFieldCompressionOn (Protocol Field Compression flag) . . . . . 352
34 P3ML Parameters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35434.1 administrativeState (Administrative state of the PPP multi-link) . . . . . . 35434.2 endPointDiscriminatorType (Endpoint discriminator type) . . . . . . . . . . 35434.3 interfaces (Physical interface list) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35534.4 mpFragmentSize (Fragment size in egress direction) . . . . . . . . . . . . . 35634.5 mrruSize (Maximum Receive Reconstructed Unit (MRRU) size) . . . . . 35734.6 netmask (Netmask of the IP address of the PPP endpoint) . . . . . . . . . 35934.7 p3mlId (PPP multi-link identifier) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35934.8 p3pIpAddr (PPP endpoint IP address) . . . . . . . . . . . . . . . . . . . . . . . . . 36034.9 shortSeqNrOn (Short sequence numbering flag) . . . . . . . . . . . . . . . . . 36134.10 ts16Excluded (Is timeslot TS16 excluded) . . . . . . . . . . . . . . . . . . . . . . 362
35 P3SL Parameters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36435.1 administrativeState (Administrative state of the PPP link) . . . . . . . . . . 36435.2 interface (Physical interface list) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36435.3 netmask (Netmask for the IP address of the PPP endpoint) . . . . . . . . 36535.4 p3pIpAddr (PPP endpoint IP address) . . . . . . . . . . . . . . . . . . . . . . . . . 36635.5 p3slId (PPP single link object instance identifier) . . . . . . . . . . . . . . . . . 36735.6 ts16Excluded (Is timeslot TS16 excluded) . . . . . . . . . . . . . . . . . . . . . . 368
36 PPTT Parameters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36936.1 administrativeState (Administrative State) . . . . . . . . . . . . . . . . . . . . . . 36936.2 interfaceNumber (Interface Number) . . . . . . . . . . . . . . . . . . . . . . . . . . 369
DN70577885 11
Flexi Transport Module Parameters
Id:0900d805809715d1Confidential
36.3 pdhLbo (PDH Line Build Out) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37036.4 pdhLineType (PDH Line Type) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37136.5 pdhPSTTPId (PDH Interface Identifier) . . . . . . . . . . . . . . . . . . . . . . . . 37336.6 unitNumber (Unit Number). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 375
37 PWMP Parameters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37637.1 bfdAdminUp (BFD actual session administration flag). . . . . . . . . . . . . 37637.2 bfdEnable (Bidirectional Forwarding Enabled). . . . . . . . . . . . . . . . . . . 37637.3 cellsConcatUl (Uplink Concatenation Factor.) . . . . . . . . . . . . . . . . . . . 37737.4 ctpList (Set of registered vcCTPs.) . . . . . . . . . . . . . . . . . . . . . . . . . . . 37837.5 labelDl (Downlink MPLS Header) . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37937.6 labelUl (Uplink MPLS Header) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38037.7 perHopBehaviour (Per hop behaviour DiffServ) . . . . . . . . . . . . . . . . . 38037.8 pkTimer (Packetization Timer) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38237.9 pwMplsId (MPLS Pseudowire Identifier) . . . . . . . . . . . . . . . . . . . . . . . 383
38 PWNE Parameters. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38438.1 bfdTimer (BFD Timer) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38438.2 bfdDetectMult (Maximum allowed number of lost control packets for BFD)
38438.3 desiredMinTxIntvl (Desired Minimum Transmit Interval) . . . . . . . . . . . 38538.4 requiredMinRxIntvl (Required Minimum Receive Interval). . . . . . . . . . 38638.5 cwEnable (Control Word Enable). . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38738.6 pwNeId (Pseudowire Network Element Identifier) . . . . . . . . . . . . . . . . 388
39 PWTIP Parameters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38939.1 administrativeState (Administrative State) . . . . . . . . . . . . . . . . . . . . . . 38939.2 attachedPWList (Attached Pseudo-Wires List) . . . . . . . . . . . . . . . . . . 38939.3 pwTipId (Pseudowire Tunnel IP Identifier) . . . . . . . . . . . . . . . . . . . . . . 39039.4 remoteIpv4Addr (Remote IPv4 Address) . . . . . . . . . . . . . . . . . . . . . . . 391
40 QOS Parameters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39340.1 perHopBehaviourWeightList (Per Hop Behaviour Weight List) . . . . . . 39340.2 assuredForwardingClass1 (Assured Forwarding Class 1 Weight Value) .
39440.3 assuredForwardingClass2 (Assured Forwarding Class 2 Weight Value) .
39540.4 assuredForwardingClass3 (Assured Forwarding Class 3 Weight Value) .
39540.5 assuredForwardingClass4 (Assured Forwarding Class 4 Weight Value) .
39640.6 bestEffort (Best Effort Weight Value) . . . . . . . . . . . . . . . . . . . . . . . . . . 39740.7 qosId (Quality of Service Configuration Identifier) . . . . . . . . . . . . . . . . 39840.8 trafficTypesMap (Quality of Service mapping table) . . . . . . . . . . . . . . 39940.9 dscpList (Differentiated Services Code Point list) . . . . . . . . . . . . . . . . 39940.10 pHB (Per Hop Behaviour) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40040.11 trafficType (Traffic type) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40240.12 vlanPrio (Vlan priority flag). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 404
41 SDHIF Parameters. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40641.1 administrativeState (Administrative State) . . . . . . . . . . . . . . . . . . . . . . 406
12 DN70577885
Flexi Transport Module Parameters
Id:0900d805809715d1Confidential
41.2 interfaceNumber (Interface Number) . . . . . . . . . . . . . . . . . . . . . . . . . . 40741.3 laserMode (Laser Mode). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40741.4 rdiOnExcessiveBer (Remote Defect Indication On Excessive Bit Error Ra-
tio) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40841.5 sdhifId (SDH Interface Identifier). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40941.6 unitNumber (Unit Number) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41041.7 xmtTraceId_HP (Sent Trace Identifier (J1, HOP)) . . . . . . . . . . . . . . . . 41141.8 xmtTraceId_RS (Sent Trace Identifier (J0, RS)) . . . . . . . . . . . . . . . . . . 411
42 STPG Parameters. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41342.1 ssmSelExt2M (SSM Selection with external 2.048 MHz) . . . . . . . . . . . 41342.2 ssmSelPDH (SSM Selection with TDM) . . . . . . . . . . . . . . . . . . . . . . . . 41442.3 ssmSelSyncE (SSM Selection with SyncE) . . . . . . . . . . . . . . . . . . . . . 41542.4 ssmTxUntagged (Send SSM message frames untagged) . . . . . . . . . . 41642.5 ssmType (SSM support network standard). . . . . . . . . . . . . . . . . . . . . . 41642.6 synchERegenOn (Activate the synchronous ethernet regenerator function)
41742.7 synchroSourceList (The synchronization sources of the BTS) . . . . . . . 41842.8 clockProtocol (Protocol of the clock source) . . . . . . . . . . . . . . . . . . . . . 41942.9 interfaceNumber (Interface number). . . . . . . . . . . . . . . . . . . . . . . . . . . 42042.10 priority (Clock source priority) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42242.11 ssmAcceptanceLevel (SSM defined value) . . . . . . . . . . . . . . . . . . . . . 42242.12 ssmEnabled (SSM enabling flag) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42342.13 ssmTimeout (SSM message timeout). . . . . . . . . . . . . . . . . . . . . . . . . . 42442.14 unitNumber (Unit number) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42542.15 timingGenPgId (Synchronisation Protection Group Identifier) . . . . . . . 426
43 SYNC Parameters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42843.1 syncId (Clock Synchronization Configuration Identifier) . . . . . . . . . . . . 428
44 TCTT Parameters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42944.1 interfaceNumber (Interface number). . . . . . . . . . . . . . . . . . . . . . . . . . . 42944.2 tcAdaptorTTPId (ATM Interface Identifier) . . . . . . . . . . . . . . . . . . . . . . 43044.3 unitNumber (Unit Number) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 431
45 TMPAR Parameters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43245.1 cacCommittedBitRate (CAC Committed Bit Rate) . . . . . . . . . . . . . . . . 43245.2 dcnCommittedBitRate (DCN Committed Bit Rate) . . . . . . . . . . . . . . . . 43445.3 externalNATIpAddress (External NAT IP Address) . . . . . . . . . . . . . . . 43545.4 farEndSctpSubnetIpAddress (Far End SCTP Subnet IP Address ) . . . 43645.5 farEndSctpSubnetMask (Far End SCTP Subnet Mask) . . . . . . . . . . . . 43745.6 minSCTPPort (Minimum SCTP port number) . . . . . . . . . . . . . . . . . . . . 43745.7 minUDPPort (Minimum UDP port number) . . . . . . . . . . . . . . . . . . . . . . 43845.8 signallingCommittedBitRate (Signalling Committed Bit Rate). . . . . . . . 43945.9 tmparId (TMPAR Object Instance Identifier) . . . . . . . . . . . . . . . . . . . . . 440
46 TOPIK Parameters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44246.1 administrativeState (Administrative State) . . . . . . . . . . . . . . . . . . . . . . 44246.2 logMeanSyncValue (Log mean synchronization value) . . . . . . . . . . . . 44246.3 masterIpAddr (IP Address of the ToP master) . . . . . . . . . . . . . . . . . . . 443
DN70577885 13
Flexi Transport Module Parameters
Id:0900d805809715d1Confidential
46.4 topId (Timing Over Packet Configuration Identifier). . . . . . . . . . . . . . . 444
47 TRDE Parameters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44647.1 atmTrafficDescriptorId (Traffic Descriptor Identifier) . . . . . . . . . . . . . . 44647.2 conformanceDefinition (Conformance Definition) . . . . . . . . . . . . . . . . 44647.3 minDesiredCellRate (Minimum Desired Cell Rate) . . . . . . . . . . . . . . . 44747.4 peakCellRate (Peak Cell Rate) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44847.5 ubrShare (UBR Share). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44947.6 userLabel (User Label) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 450
48 TWAMP Parameters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45248.1 administrativeState (Lock or unlock a TWAMP session) . . . . . . . . . . . 45248.2 destIpAddress (TWAMP session destination IP address) . . . . . . . . . . 45348.3 destPort (TWAMP session destination port) . . . . . . . . . . . . . . . . . . . . 45348.4 dscp (DSCP value for TWAMP message transmission) . . . . . . . . . . . 45448.5 messageSize (TWAMP initiator message size) . . . . . . . . . . . . . . . . . . 45548.6 plrAlarmThreshold (Packet loss ratio alarm threshold) . . . . . . . . . . . . 45648.7 rttAlarmThreshold (Round-trip-time alarm threshold) . . . . . . . . . . . . . 45748.8 sourceIpAddress (TWAMP initiator messages source IP address) . . . 45848.9 twampId (TWAMP session identifier). . . . . . . . . . . . . . . . . . . . . . . . . . 459
49 UNIT Parameters. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46149.1 enableRP301Interface (Enable RP3-01 interface). . . . . . . . . . . . . . . . 46149.2 unitId (Unit Identifier) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46149.3 unitTypeActual (Installed hardware unit type) . . . . . . . . . . . . . . . . . . . 46249.4 unitTypeExpected (Expected hardware unit type) . . . . . . . . . . . . . . . . 464
50 VCCT Parameters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46750.1 VCI (Virtual Channel Identifier) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46750.2 VPI (Virtual Path Identifier) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46750.3 interfaceNumber (Interface Number) . . . . . . . . . . . . . . . . . . . . . . . . . . 46850.4 trafficDescriptorId (Traffic Descriptor Pointer) . . . . . . . . . . . . . . . . . . . 46950.5 unitNumber (Unit Number). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47050.6 vcCTPId (Virtual Channel Identifier (VCI)) . . . . . . . . . . . . . . . . . . . . . . 471
51 VCTT Parameters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47251.1 VCI (Virtual Channel Identifier) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47251.2 VPI (Virtual Path Identifier) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47251.3 aalProfilePtr (ATM Adaptation Layer (AAL) Profile Pointer) . . . . . . . . 47351.4 interfaceNumber (Interface Number) . . . . . . . . . . . . . . . . . . . . . . . . . . 47451.5 unitNumber (Unit Number). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47551.6 vcTTPId (Virtual Channel Trail Termination Point Identifier) . . . . . . . . 476
52 VPCT Parameters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47852.1 VPI (Virtual Path Identifier) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47852.2 interfaceNumber (Interface Number) . . . . . . . . . . . . . . . . . . . . . . . . . . 47852.3 trafficDescriptorId (Traffic Descriptor Pointer) . . . . . . . . . . . . . . . . . . . 47952.4 unitNumber (Unit Number). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48052.5 vpCTPId (Virtual Path Identifier (VPI)) . . . . . . . . . . . . . . . . . . . . . . . . . 481
53 VPTT Parameters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 483
14 DN70577885
Flexi Transport Module Parameters
Id:0900d805809715d1Confidential
53.1 VPI (Virtual Path Identifier) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48353.2 interfaceNumber (Interface Number) . . . . . . . . . . . . . . . . . . . . . . . . . . 48353.3 unitNumber (Unit Number) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48453.4 vpTTPId (Virtual Path Trail Termination Point Identifier) . . . . . . . . . . . 485
DN70577885 15
Flexi Transport Module Parameters
Id:0900d805809715d1Confidential
List of tablesTable 1 aal2NodeId (AAL2 Node Identifier) . . . . . . . . . . . . . . . . . . . . . . . . . . . . 68Table 2 AAL2EndAddress (AAL2 End Address) . . . . . . . . . . . . . . . . . . . . . . . . 69Table 3 VCI (Virtual Channel Identifier) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 69Table 4 VPI (Virtual Path Identifier) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 70Table 5 aal2sigTTPId (AAL2 Signalling Link Identifier) . . . . . . . . . . . . . . . . . . . 71Table 6 interfaceNumber (Interface Number) . . . . . . . . . . . . . . . . . . . . . . . . . . 72Table 7 stcAlarmEnable (Signalling Transport Converter Alarm Enable) . . . . . 73Table 8 unitNumber (Unit Number) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 74Table 9 VCI (Virtual Channel Identifier) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 76Table 10 VPI (Virtual Path Identifier) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 76Table 11 aal2pathTTPId (AAL2 User Path Identifier) . . . . . . . . . . . . . . . . . . . . . 77Table 12 interfaceNumber (Interface Number) . . . . . . . . . . . . . . . . . . . . . . . . . . 79Table 13 pid (Path Identifier) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 79Table 14 queue2Weight (Weight of AAL2 user path queue Q2) . . . . . . . . . . . . . 80Table 15 queue3Weight (Weight of AAL2 user path queue Q3) . . . . . . . . . . . . . 81Table 16 queue4Weight (Weight of AAL2 user path queue Q4) . . . . . . . . . . . . . 82Table 17 unitNumber (Unit Number) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 83Table 18 atmAccessProfileId (ATM Access Profile Identifier) . . . . . . . . . . . . . . . 84Table 19 egressBandwidth (Egress Bandwidth) . . . . . . . . . . . . . . . . . . . . . . . . . 84Table 20 ingressBandwidth (Ingress Bandwidth) . . . . . . . . . . . . . . . . . . . . . . . . . 86Table 21 amgrId (Account Manager Identifier) . . . . . . . . . . . . . . . . . . . . . . . . . . 88Table 22 ldapConnectionType (LDAP Server TLS access mode) . . . . . . . . . . . . 88Table 23 primaryLdapPort (Port Number of Primary LDAP Server) . . . . . . . . . . 89Table 24 primaryLdapServer (IP address of Primary LDAP Server) . . . . . . . . . . 90Table 25 VCI (Virtual Channel Identifier) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 92Table 26 VPI (Virtual Path Identifier) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 92Table 27 interfaceNumber (Interface Identifier) . . . . . . . . . . . . . . . . . . . . . . . . . . 93Table 28 nbapTTPId (Upper Layer Path Identifier) . . . . . . . . . . . . . . . . . . . . . . . 94Table 29 nbapType (Upper Layer Connection Type) . . . . . . . . . . . . . . . . . . . . . . 96Table 30 unitNumber (Unit Number) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 97Table 31 bfdActivation (BFD session activation flag) . . . . . . . . . . . . . . . . . . . . . . 99Table 32 bfdAdminUp (BFD session admin down state control) . . . . . . . . . . . . 100Table 33 bfdDestAddress (Destination IP address for the BFD session) . . . . . 101Table 34 bfdDetectMult (BFD session packets lost detection time multiplier) . . 102Table 35 bfdGrp (BFD group reference) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 103Table 36 bfdId (BFD session identifier) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 104Table 37 bfdSourceIpAddr (Source IP address for the BFD session) . . . . . . . . 104Table 38 bfdSourceUdpPort (UDP source port of the BFD session) . . . . . . . . . 105Table 39 bfdType (BFD session type) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 106Table 40 desMinTxInt (Desired minimum BFD control word transmit interval) . 107Table 41 function (BFD session function definition) . . . . . . . . . . . . . . . . . . . . . . 108Table 42 reqMinRxInt (Required minimum BFD control word receive interval) . 110Table 43 bfdGrpId (BFD Group Identifier ) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 111Table 44 atmFabricId (ATM Fabric Identifier) . . . . . . . . . . . . . . . . . . . . . . . . . . 112Table 45 ubrPlusEnabled (UBR+ Enabled) . . . . . . . . . . . . . . . . . . . . . . . . . . . . 113
16 DN70577885
Flexi Transport Module Parameters
Id:0900d805809715d1Confidential
Table 46 vccBundleEnabled (VCC Bundle Enabling Flag) . . . . . . . . . . . . . . . . . 114Table 47 btsCertificateUpdateTime (BTS certificate update time) . . . . . . . . . . . 115Table 48 caCertificateUpdateTime (CA certificate update time) . . . . . . . . . . . . . 115Table 49 caSubjectName (CMP server subject name) . . . . . . . . . . . . . . . . . . . . 116Table 50 certhId (Certification Handler Identifier) . . . . . . . . . . . . . . . . . . . . . . . . 117Table 51 cmpServerIpAddress (CMP Server IP Address) . . . . . . . . . . . . . . . . . 118Table 52 cmpServerPort (CMP Server Port) . . . . . . . . . . . . . . . . . . . . . . . . . . . 119Table 53 crServerIpAddress (CR Server IP Address) . . . . . . . . . . . . . . . . . . . . 119Table 54 crServerPort (CR Server Port) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 120Table 55 crlUpdatePeriod (Certificate Revocation List update period) . . . . . . . . 121Table 56 cesMinUDPPort (CES over PSN source port value range) . . . . . . . . . 123Table 57 cesifId (CES over PSN interface identifier) . . . . . . . . . . . . . . . . . . . . . 124Table 58 administrativeState (Administrative state) . . . . . . . . . . . . . . . . . . . . . . 125Table 59 cesPWid (CES over PSN Pseudowire Identifier) . . . . . . . . . . . . . . . . . 126Table 60 dscp (DSCP value) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 127Table 61 framesNumber (Number of frames per CESoPSN packet) . . . . . . . . . 127Table 62 jitterBufferSize (Jitter Buffer Size) . . . . . . . . . . . . . . . . . . . . . . . . . . . . 128Table 63 payloadTimeslots (Payload timeslots of TDM frame) . . . . . . . . . . . . . 129Table 64 remoteUDPPort (Remote UDP port number for CES over PSN) . . . . . 132Table 65 cesPWTid (CES over PSN pseudowire tunnel identifier) . . . . . . . . . . . 134Table 66 destIpAddress (Destination IP address) . . . . . . . . . . . . . . . . . . . . . . . 134Table 67 acceptableFrameTypes (Switch Port Acceptable Frame Types) . . . . . 136Table 68 administrativeState (Administrative State) . . . . . . . . . . . . . . . . . . . . . . 137Table 69 ethLinkId (Ethernet Link Identifier) . . . . . . . . . . . . . . . . . . . . . . . . . . . . 137Table 70 flushFdbOnLos (Flush fdb on LOS mode) . . . . . . . . . . . . . . . . . . . . . . 141Table 71 l2BurstSize (Switch Port egress Shaper Burst Size) . . . . . . . . . . . . . . 142Table 72 l2IngressRate (Switch Port ingress RateLimiter Rate ) . . . . . . . . . . . . 143Table 73 l2ShaperRate (Switch Port egress Shaper Rate) . . . . . . . . . . . . . . . . 146Table 74 l2VlanIdList (Switch Port VLAN Member List) . . . . . . . . . . . . . . . . . . . 150Table 75 highValue (Switch Port VLAN Member Range High Value) . . . . . . . . . 151Table 76 lowValue (Switch Port VLAN Member Range Low Value) . . . . . . . . . . 152Table 77 linkOAMEnabled (Link OAM enabling flag) . . . . . . . . . . . . . . . . . . . . . 153Table 78 linkOAMProfile (Link OAM profile reference) . . . . . . . . . . . . . . . . . . . . 154Table 79 macAddr (MAC address) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 155Table 80 portDefaultPriority (Switch Port Default VLAN Priority) . . . . . . . . . . . . 155Table 81 portDefaultVlanId (Switch Port Default VLAN Identifier) . . . . . . . . . . . 156Table 82 speedAndDuplex (Speed and Duplex flag) . . . . . . . . . . . . . . . . . . . . . 157Table 83 synchEMode (Synchronous ethernet mode) . . . . . . . . . . . . . . . . . . . . 159Table 84 afrLinkInterfaceId (Fractional Interface Identifier) . . . . . . . . . . . . . . . . 160Table 85 afrTimeSlotSequence (ATM over Fractional JT1 Time Slot Sequence) . .
161Table 86 interfaceNumber (Interface Identifier) . . . . . . . . . . . . . . . . . . . . . . . . . 163Table 87 unitNumber (Unit Number) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 164Table 88 adaptationVersionMajor (Adaptation Version Major) . . . . . . . . . . . . . . 165Table 89 ftmId (BTS Transport Identifier) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 165Table 90 locationName (Location Name) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 166Table 91 softwareReleaseVersion (Software Release Version) . . . . . . . . . . . . . 167
DN70577885 17
Flexi Transport Module Parameters
Id:0900d805809715d1Confidential
Table 92 systemTitle (System Title) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 168Table 93 userLabel (User Label) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 169Table 94 VCI (Virtual Channel Identifier) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 170Table 95 VPI (Virtual Path Identifier) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 170Table 96 atmIfNetId (ATM IP Net Interface Identifier) . . . . . . . . . . . . . . . . . . . . 171Table 97 destIpAddr (Destination IP Address) . . . . . . . . . . . . . . . . . . . . . . . . . . 173Table 98 interfaceNumber (Interface Number) . . . . . . . . . . . . . . . . . . . . . . . . . 174Table 99 unitNumber (Unit Number) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 175Table 100 cir (Committed information rate) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 176Table 101 confCost (OSPF configured interface cost) . . . . . . . . . . . . . . . . . . . . 177Table 102 helloInterval (OSPF keepalive message transmission interval) . . . . . 178Table 103 ieifId (Identifier of the plain Ethernet interface) . . . . . . . . . . . . . . . . . . 179Table 104 interfaceArea (OSPF interface area) . . . . . . . . . . . . . . . . . . . . . . . . . 180Table 105 ipAddr (IP Address Info in the Transport Network) . . . . . . . . . . . . . . . 181Table 106 localIpAddr (Local Address of the IP Interface) . . . . . . . . . . . . . . . . . 182Table 107 netmask (IP Network Mask) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 182Table 108 mtu (Maximum transfer unit) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 183Table 109 mtuMismatchDetection (MTU mismatch detection in use) . . . . . . . . . 184Table 110 ospfWithBfd (OSPF uses additionally BFD) . . . . . . . . . . . . . . . . . . . . 185Table 111 proxyArpIpAddrList (List of proxy ARP IP addresses for this interface.) . .
186Table 112 qosEnabled (QOS traffic priorisation enabling flag) . . . . . . . . . . . . . . 186Table 113 retransInterval (OSPF LSA retransmission interval) . . . . . . . . . . . . . . 188Table 114 routerDeadInterval (OSPF router read interval) . . . . . . . . . . . . . . . . . 188Table 115 sbs (Shaper burst size) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 189Table 116 sbsTotal (Total shaper burst size) . . . . . . . . . . . . . . . . . . . . . . . . . . . . 190Table 117 shapedBandwidth (Shaped Bandwidth) . . . . . . . . . . . . . . . . . . . . . . . 191Table 118 sir (Shaper information rate) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 193Table 119 sirTotal (Total shaper information rate) . . . . . . . . . . . . . . . . . . . . . . . . 194Table 120 trafficPathShapingEnable (Traffic path shaping enabling flag) . . . . . . 195Table 121 transmitDelay (OSPF packet transmission delay) . . . . . . . . . . . . . . . 196Table 122 upperLayerShaping (Upper Layer Shaping Enabled Flag) . . . . . . . . . 197Table 123 vlanEnabled (Vlan Enabled flag) . . . . . . . . . . . . . . . . . . . . . . . . . . . . 198Table 124 vlanId (Vlan ID) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 198Table 125 client_identifier (Entry set for DHCP clients identified by a system name)
200Table 126 dhcpClientIdentifier (DHCP Client Identifier) . . . . . . . . . . . . . . . . . . . . 200Table 127 dhcpFixedIpAddress (DHCP Fixed IP Address) . . . . . . . . . . . . . . . . . 201Table 128 dhcpAccessId (DHCP Server Identifier) . . . . . . . . . . . . . . . . . . . . . . . 202Table 129 hardware_identifier (Entry set of DHCP clients identified by a MAC
address) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 203Table 130 dhcpFixedIpAddress (DHCP Fixed IP Address) . . . . . . . . . . . . . . . . . 204Table 131 dhcpHardwareIdentifier (DHCP Hardware Identifier) . . . . . . . . . . . . . 205Table 132 range_identifier (DHCP server IP address pool) . . . . . . . . . . . . . . . . . 206Table 133 dhcpRangeEnd (DHCP Range End IP Address) . . . . . . . . . . . . . . . . 206Table 134 dhcpRangeStart (DHCP Range Start IP Address) . . . . . . . . . . . . . . . 207Table 135 administrativeState (Administrative State) . . . . . . . . . . . . . . . . . . . . . 209Table 136 imaGroupId (IMA group identifier) . . . . . . . . . . . . . . . . . . . . . . . . . . . . 210
18 DN70577885
Flexi Transport Module Parameters
Id:0900d805809715d1Confidential
Table 137 imaVersionId (IMA Version Identifier) . . . . . . . . . . . . . . . . . . . . . . . . . 211Table 138 interfaceNumber (Interface Number) . . . . . . . . . . . . . . . . . . . . . . . . . . 212Table 139 interfaces (Physical interface list) . . . . . . . . . . . . . . . . . . . . . . . . . . . . 212Table 140 minNumLinks (Minimum Number of Links) . . . . . . . . . . . . . . . . . . . . . 213Table 141 unitNumber (Unit Number) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 214Table 142 ntpAccessId (NTP Identifier) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 216Table 143 ntpServers (List of NTP Server IP Addresses) . . . . . . . . . . . . . . . . . . 216Table 144 bfdHoldUpTime (BFD throttle time for re-installing protection routes) . 218Table 145 btsId (BTS Identifier) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 219Table 146 btsIpAddr (Base Station IP Address) . . . . . . . . . . . . . . . . . . . . . . . . . . 219Table 147 cPlaneIpAddress (Control-plane application IP address) . . . . . . . . . . 220Table 148 cesopsnIpAddress (CES over PSN application IP address) . . . . . . . . 222Table 149 disableFtp (Disable FTP server) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 223Table 150 flexBusIpAddr (Public IP Address of Flexbus Part of BTS) . . . . . . . . . 224Table 151 fpLocalUdpPort (Local UDP port for small packets multiplexing) . . . . 224Table 152 fpMuxAmount (Maximum amount of small packets that can be
multiplexed) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 225Table 153 fpMuxDelay (Small packets multiplexing delay time) . . . . . . . . . . . . . . 226Table 154 fpRemoteUdpPort (Remote UDP port for small packets multiplexing) 227Table 155 ftmIpAddr (Flexi Transport Module IP Address) . . . . . . . . . . . . . . . . . . 228Table 156 ftmNetmask (Netmask of the public IP address) . . . . . . . . . . . . . . . . . 229Table 157 iHSPAAdapterCommissioningParameter (I-HSPA adapter initial commis-
sioning parameters) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 230Table 158 iHSPAmode (I-HSPA mode activation flag) . . . . . . . . . . . . . . . . . . . . . 231Table 159 icmpResponseEnabled (Enable response to ICMP traffic) . . . . . . . . . 231Table 160 ipNodeId (IP Node Identifier) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 232Table 161 linkOAMLoopbackSupport (Link OAM remote loopback discovery enabling
flag) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 233Table 162 mPlaneIpAddress (Management -plane application IP address) . . . . . 234Table 163 mtu (Maximum transfer unit of the BTS) . . . . . . . . . . . . . . . . . . . . . . . 235Table 164 oamCir (Committed information rate for Service OAM messages) . . . 236Table 165 oamTlvReply (Optional TLV message reply flag) . . . . . . . . . . . . . . . . 237Table 166 omsTls (TLS usage towards the O&M system) . . . . . . . . . . . . . . . . . . 238Table 167 ret1IpAddr (RET IP Address) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 239Table 168 rncIpAddr (RNC IP Address) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 240Table 169 sPlaneIpAddress (Synchronization-plane application IP address) . . . 241Table 170 transportMode (BTS transport mode) . . . . . . . . . . . . . . . . . . . . . . . . . 242Table 171 twampMessageRate (TWAMP initiator rate for sending messages) . . 243Table 172 twampReflectorOn (TWAMP message response enabling flag) . . . . . 244Table 173 twampReflectorPort (TWAMP reflector port number) . . . . . . . . . . . . . 245Table 174 twampSourcePort (TWAMP source port number) . . . . . . . . . . . . . . . . 246Table 175 uPlane2IpAddress (Second user-plane application IP address) . . . . . 247Table 176 uPlane2IpInterface (Second user-plane application IP network interface)
248Table 177 uPlaneIpAddress (User plane application IP address) . . . . . . . . . . . . 250Table 178 uPlaneIpInterface (User-plane application IP network interface) . . . . . 251Table 179 RmExceptions (Restricted Mode Exception) . . . . . . . . . . . . . . . . . . . . 254Table 180 sourceTwoDiscr (How is source two defined?) . . . . . . . . . . . . . . . . . . 255
DN70577885 19
Flexi Transport Module Parameters
Id:0900d805809715d1Confidential
Table 181 sourceTwoIpAddr (IP address for source two) . . . . . . . . . . . . . . . . . . 256Table 182 sourceTwoNetMask (IP Subnet Mask) . . . . . . . . . . . . . . . . . . . . . . . . 257Table 183 userLabel (User Label) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 258Table 184 iprmId (IP Restricted Mode Identifier) . . . . . . . . . . . . . . . . . . . . . . . . . 259Table 185 ipRoutingTableId (IP Routing Table Identifier) . . . . . . . . . . . . . . . . . . 260Table 186 staticRoutes (List of static routes) . . . . . . . . . . . . . . . . . . . . . . . . . . . . 261Table 187 bfdId (BFD route protection session identifier) . . . . . . . . . . . . . . . . . . 262Table 188 destIpAddr (Route destination IP address) . . . . . . . . . . . . . . . . . . . . . 262Table 189 gateway (IP address of the next hop of the route) . . . . . . . . . . . . . . . 263Table 190 netmask (Netmask of the destination IP address) . . . . . . . . . . . . . . . 264Table 191 preference (Preference value for the route) . . . . . . . . . . . . . . . . . . . . 265Table 192 cESoPSN (CES over PSN flag) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 267Table 193 cir (Committed information rate) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 268Table 194 confCost (OSPF configured interface cost) . . . . . . . . . . . . . . . . . . . . 269Table 195 helloInterval (OSPF keepalive message transmission interval) . . . . . 269Table 196 interfaceArea (OSPF interface area) . . . . . . . . . . . . . . . . . . . . . . . . . 270Table 197 localIpAddr (Local Address of the IP Interface) . . . . . . . . . . . . . . . . . 271Table 198 mtuMismatchDetection (MTU mismatch detection in use) . . . . . . . . . 272Table 199 netmask (IP network mask of the local IP address) . . . . . . . . . . . . . . 273Table 200 ospfWithBfd (OSPF uses additionally BFD) . . . . . . . . . . . . . . . . . . . . 273Table 201 proxyArpIpAddrList (List of proxy ARP IP addresses for this interface.) . .
274Table 202 qosEnabled (QOS traffic priorisation enabling flag) . . . . . . . . . . . . . . 275Table 203 retransInterval (OSPF LSA retransmission interval) . . . . . . . . . . . . . . 276Table 204 routerDeadInterval (OSPF router read interval) . . . . . . . . . . . . . . . . . 277Table 205 sbs (Shaper burst size) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 278Table 206 sir (Shaper information rate) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 279Table 207 transmitDelay (OSPF packet transmission delay) . . . . . . . . . . . . . . . 280Table 208 vlanId (VLAN identifier) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 281Table 209 vlanIfNetId (VLAN interface object identifier) . . . . . . . . . . . . . . . . . . . 282Table 210 dscpMap (DSCP to priority queue map) . . . . . . . . . . . . . . . . . . . . . . . 283Table 211 dscp (DSCP value) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 284Table 212 priorityQueue (Priority queue identifier) . . . . . . . . . . . . . . . . . . . . . . . 285Table 213 enableLayer2Switching (Ethernet Switch Enable) . . . . . . . . . . . . . . . 286Table 214 l2PriorityQueueWeight2 (Layer 2 switch member weight for priority queue
2) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 287Table 215 l2PriorityQueueWeight3 (Layer 2 switch member weight for priority queue
3) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 287Table 216 l2PriorityQueueWeight4 (Layer 2 switch member weight for priority queue
4) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 288Table 217 l2PriorityQueueWeight5 (Layer 2 switch member weight for priority queue
5) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 289Table 218 l2PriorityQueueWeight6 (Layer 2 switch member weight for priority queue
6) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 290Table 219 portDefaultPriority (Switch Port Default VLAN Priority (internal Port)) 291Table 220 portDefaultVlanId (Switch Port Default VLAN Identifier (internal Port)) 292Table 221 priorityQueueNonIP (Priority queue for non-IP frames) . . . . . . . . . . . 293Table 222 priorityQueuePcp0 (Priority queue for ethernet frames with VLAN PCP bits
20 DN70577885
Flexi Transport Module Parameters
Id:0900d805809715d1Confidential
0) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 294Table 223 priorityQueuePcp1 (Priority queue for ethernet frames with VLAN PCP bits
1) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 295Table 224 priorityQueuePcp2 (Priority queue for ethernet frames with VLAN PCP bits
2) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 296Table 225 priorityQueuePcp3 (Priority queue for ethernet frames with VLAN PCP bits
3) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 297Table 226 priorityQueuePcp4 (Priority queue for ethernet frames with VLAN PCP bits
4) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 298Table 227 priorityQueuePcp5 (Priority queue for ethernet frames with VLAN PCP bits
5) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 299Table 228 priorityQueuePcp6 (Priority queue for ethernet frames with VLAN PCP bits
6) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 300Table 229 priorityQueuePcp7 (Priority queue for ethernet frames with VLAN PCP bits
7) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 301Table 230 priorityQueueUntagged (Priority queue for untagged ethernet frames) 302Table 231 qosClassification (QoS Classification Mode) . . . . . . . . . . . . . . . . . . . . 303Table 232 switchId (Layer 2 Switch Object Identifier) . . . . . . . . . . . . . . . . . . . . . . 304Table 233 vlanAwareSwitch (VLAN Aware Switching Enable) . . . . . . . . . . . . . . . 305Table 234 assocId (Maintenance association identifier) . . . . . . . . . . . . . . . . . . . . 307Table 235 maName (Name of the maintenance domain) . . . . . . . . . . . . . . . . . . . 307Table 236 vlanId (VLAN identifier of the maintenance association) . . . . . . . . . . . 308Table 237 domainId (Maintenance domain identifier) . . . . . . . . . . . . . . . . . . . . . . 310Table 238 mdLevel (Level of the maintenance domain) . . . . . . . . . . . . . . . . . . . . 310Table 239 mdName (Name of the maintenance domain) . . . . . . . . . . . . . . . . . . . 311Table 240 aisEnabled (AIS message transmission enabling flag) . . . . . . . . . . . . 313Table 241 aisTxPeriod (AIS messages transmission period) . . . . . . . . . . . . . . . . 313Table 242 ccmTxPeriod (Continuity Check Messages transmission period) . . . . 314Table 243 enableCcm (Allow sending of CCM messages and reset CCM counters) .
315Table 244 ethernetPort (Ethernet link reference) . . . . . . . . . . . . . . . . . . . . . . . . . 316Table 245 oammepId (Maintenance association endpoint identifier) . . . . . . . . . . 317Table 246 remoteMepList (Remote maintenance association endpoints list) . . . . 318Table 247 macAddr (MAC address of the remote MEP) . . . . . . . . . . . . . . . . . . . 319Table 248 mepId (Remote maintenance association endpoint identifier) . . . . . . . 320Table 249 vlanPrio (VLAN PCP bits) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 320Table 250 activeMode (Link OAM operational mode at local peer) . . . . . . . . . . . 322Table 251 alarmClearanceDelay (Link OAM Link Critical Event Alarm clearance
delay) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 323Table 252 efEventThreshold (Errored Frame Event counting threshold) . . . . . . . 323Table 253 efEventWindow (Errored Frame Event counting interval) . . . . . . . . . . 324Table 254 efpEventThreshold (Errored Frame Period Event counting threshold) 325Table 255 efpEventWindow (Errored Frame Period Event counting interval) . . . 326Table 256 efssEventThreshold (Errored Frame Seconds Summary Event counting
threshold) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 327Table 257 efssEventWindow (Errored Frame Seconds Summary Event counting
interval) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 328Table 258 eventRepetition (OAM PDU message transmission rate) . . . . . . . . . . 329Table 259 eventSupport (Link OAM event support flag) . . . . . . . . . . . . . . . . . . . . 330
DN70577885 21
Flexi Transport Module Parameters
Id:0900d805809715d1Confidential
Table 260 linkLostTime (Link OAM link lost time) . . . . . . . . . . . . . . . . . . . . . . . . 331Table 261 linkOAMProfileName (Link OAM Profile Name) . . . . . . . . . . . . . . . . . 332Table 262 loopBackTime (Link OAM loopback duration) . . . . . . . . . . . . . . . . . . . 333Table 263 profileId (Profile instance identifier) . . . . . . . . . . . . . . . . . . . . . . . . . . . 334Table 264 testFrameRate (Link OAM loopback test message rate) . . . . . . . . . . 335Table 265 testFrameSize (Link OAM loopback test message frame size) . . . . . 336Table 266 confPref (OSPF routing preference value) . . . . . . . . . . . . . . . . . . . . . 337Table 267 ospfAreas (OSPF area list) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 337Table 268 areaId (OSPF area identifier) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 338Table 269 areaStub (OSPF area stub flag) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 339Table 270 ospfEnabled (OSPF enabling flag) . . . . . . . . . . . . . . . . . . . . . . . . . . . 340Table 271 ospfRouterId (OSPF router identification) . . . . . . . . . . . . . . . . . . . . . . 341Table 272 ospfV2Id (OSPF configuration identifier) . . . . . . . . . . . . . . . . . . . . . . 342Table 273 refBandwidth (Reference bandwidth for OSPF cost equal to 1) . . . . . 343Table 274 spfDelay (OSPF Shortest Path First recalculation delay) . . . . . . . . . . 343Table 275 spfHoldTime (OSPF Shortest Path First hold time) . . . . . . . . . . . . . . 344Table 276 spfMaxHoldTime (OSPF maximum Shortest Path First hold time) . . . 345Table 277 acFieldCompressionOn (Access Control Field Compression flag) . . . 347Table 278 fcsFieldLength (Frame Check Sequence field size) . . . . . . . . . . . . . 347Table 279 magicNumberOn (Magic number flag) . . . . . . . . . . . . . . . . . . . . . . . . 348Table 280 mruSize (Maximum Receive Unit (MRU) size) . . . . . . . . . . . . . . . . . . 349Table 281 p3lpId (PPP link identifier) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 351Table 282 protocolFieldCompressionOn (Protocol Field Compression flag) . . . . 352Table 283 administrativeState (Administrative state of the PPP multi-link) . . . . . 354Table 284 endPointDiscriminatorType (Endpoint discriminator type) . . . . . . . . . 354Table 285 interfaces (Physical interface list) . . . . . . . . . . . . . . . . . . . . . . . . . . . . 355Table 286 mpFragmentSize (Fragment size in egress direction) . . . . . . . . . . . . 356Table 287 mrruSize (Maximum Receive Reconstructed Unit (MRRU) size) . . . . 357Table 288 netmask (Netmask of the IP address of the PPP endpoint) . . . . . . . . 359Table 289 p3mlId (PPP multi-link identifier) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 359Table 290 p3pIpAddr (PPP endpoint IP address) . . . . . . . . . . . . . . . . . . . . . . . . 360Table 291 shortSeqNrOn (Short sequence numbering flag) . . . . . . . . . . . . . . . . 361Table 292 ts16Excluded (Is timeslot TS16 excluded) . . . . . . . . . . . . . . . . . . . . . 362Table 293 administrativeState (Administrative state of the PPP link) . . . . . . . . . 364Table 294 interface (Physical interface list) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 364Table 295 netmask (Netmask for the IP address of the PPP endpoint) . . . . . . . 365Table 296 p3pIpAddr (PPP endpoint IP address) . . . . . . . . . . . . . . . . . . . . . . . . 366Table 297 p3slId (PPP single link object instance identifier) . . . . . . . . . . . . . . . . 367Table 298 ts16Excluded (Is timeslot TS16 excluded) . . . . . . . . . . . . . . . . . . . . . 368Table 299 administrativeState (Administrative State) . . . . . . . . . . . . . . . . . . . . . 369Table 300 interfaceNumber (Interface Number) . . . . . . . . . . . . . . . . . . . . . . . . . 369Table 301 pdhLbo (PDH Line Build Out) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 370Table 302 pdhLineType (PDH Line Type) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 371Table 303 pdhPSTTPId (PDH Interface Identifier) . . . . . . . . . . . . . . . . . . . . . . . . 373Table 304 unitNumber (Unit Number) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 375Table 305 bfdAdminUp (BFD actual session administration flag) . . . . . . . . . . . . 376Table 306 bfdEnable (Bidirectional Forwarding Enabled) . . . . . . . . . . . . . . . . . . 376
22 DN70577885
Flexi Transport Module Parameters
Id:0900d805809715d1Confidential
Table 307 cellsConcatUl (Uplink Concatenation Factor.) . . . . . . . . . . . . . . . . . . . 377Table 308 ctpList (Set of registered vcCTPs.) . . . . . . . . . . . . . . . . . . . . . . . . . . . 378Table 309 labelDl (Downlink MPLS Header) . . . . . . . . . . . . . . . . . . . . . . . . . . . . 379Table 310 labelUl (Uplink MPLS Header) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 380Table 311 perHopBehaviour (Per hop behaviour DiffServ) . . . . . . . . . . . . . . . . . 380Table 312 pkTimer (Packetization Timer) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 382Table 313 pwMplsId (MPLS Pseudowire Identifier) . . . . . . . . . . . . . . . . . . . . . . . 383Table 314 bfdTimer (BFD Timer) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 384Table 315 bfdDetectMult (Maximum allowed number of lost control packets for BFD)
384Table 316 desiredMinTxIntvl (Desired Minimum Transmit Interval) . . . . . . . . . . . 385Table 317 requiredMinRxIntvl (Required Minimum Receive Interval) . . . . . . . . . . 386Table 318 cwEnable (Control Word Enable) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 387Table 319 pwNeId (Pseudowire Network Element Identifier) . . . . . . . . . . . . . . . . 388Table 320 administrativeState (Administrative State) . . . . . . . . . . . . . . . . . . . . . . 389Table 321 attachedPWList (Attached Pseudo-Wires List) . . . . . . . . . . . . . . . . . . 389Table 322 pwTipId (Pseudowire Tunnel IP Identifier) . . . . . . . . . . . . . . . . . . . . . . 390Table 323 remoteIpv4Addr (Remote IPv4 Address) . . . . . . . . . . . . . . . . . . . . . . . 391Table 324 perHopBehaviourWeightList (Per Hop Behaviour Weight List) . . . . . . 393Table 325 assuredForwardingClass1 (Assured Forwarding Class 1 Weight Value) .
394Table 326 assuredForwardingClass2 (Assured Forwarding Class 2 Weight Value) .
395Table 327 assuredForwardingClass3 (Assured Forwarding Class 3 Weight Value) .
395Table 328 assuredForwardingClass4 (Assured Forwarding Class 4 Weight Value) .
396Table 329 bestEffort (Best Effort Weight Value) . . . . . . . . . . . . . . . . . . . . . . . . . . 397Table 330 qosId (Quality of Service Configuration Identifier) . . . . . . . . . . . . . . . . 398Table 331 trafficTypesMap (Quality of Service mapping table) . . . . . . . . . . . . . . 399Table 332 dscpList (Differentiated Services Code Point list) . . . . . . . . . . . . . . . . 399Table 333 pHB (Per Hop Behaviour) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 400Table 334 trafficType (Traffic type) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 402Table 335 vlanPrio (Vlan priority flag) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 404Table 336 administrativeState (Administrative State) . . . . . . . . . . . . . . . . . . . . . . 406Table 337 interfaceNumber (Interface Number) . . . . . . . . . . . . . . . . . . . . . . . . . . 407Table 338 laserMode (Laser Mode) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 407Table 339 rdiOnExcessiveBer (Remote Defect Indication On Excessive Bit Error
Ratio) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 408Table 340 sdhifId (SDH Interface Identifier) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 409Table 341 unitNumber (Unit Number) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 410Table 342 xmtTraceId_HP (Sent Trace Identifier (J1, HOP)) . . . . . . . . . . . . . . . . 411Table 343 xmtTraceId_RS (Sent Trace Identifier (J0, RS)) . . . . . . . . . . . . . . . . . 411Table 344 ssmSelExt2M (SSM Selection with external 2.048 MHz) . . . . . . . . . . 413Table 345 ssmSelPDH (SSM Selection with TDM) . . . . . . . . . . . . . . . . . . . . . . . 414Table 346 ssmSelSyncE (SSM Selection with SyncE) . . . . . . . . . . . . . . . . . . . . . 415Table 347 ssmTxUntagged (Send SSM message frames untagged) . . . . . . . . . . 416Table 348 ssmType (SSM support network standard) . . . . . . . . . . . . . . . . . . . . . 416
DN70577885 23
Flexi Transport Module Parameters
Id:0900d805809715d1Confidential
Table 349 synchERegenOn (Activate the synchronous ethernet regenerator function) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 417
Table 350 synchroSourceList (The synchronization sources of the BTS) . . . . . . 418Table 351 clockProtocol (Protocol of the clock source) . . . . . . . . . . . . . . . . . . . . 419Table 352 interfaceNumber (Interface number) . . . . . . . . . . . . . . . . . . . . . . . . . . 420Table 353 priority (Clock source priority) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 422Table 354 ssmAcceptanceLevel (SSM defined value) . . . . . . . . . . . . . . . . . . . . 422Table 355 ssmEnabled (SSM enabling flag) . . . . . . . . . . . . . . . . . . . . . . . . . . . . 423Table 356 ssmTimeout (SSM message timeout) . . . . . . . . . . . . . . . . . . . . . . . . . 424Table 357 unitNumber (Unit number) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 425Table 358 timingGenPgId (Synchronisation Protection Group Identifier) . . . . . . 426Table 359 syncId (Clock Synchronization Configuration Identifier) . . . . . . . . . . . 428Table 360 interfaceNumber (Interface number) . . . . . . . . . . . . . . . . . . . . . . . . . . 429Table 361 tcAdaptorTTPId (ATM Interface Identifier) . . . . . . . . . . . . . . . . . . . . . 430Table 362 unitNumber (Unit Number) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 431Table 363 cacCommittedBitRate (CAC Committed Bit Rate) . . . . . . . . . . . . . . . 432Table 364 dcnCommittedBitRate (DCN Committed Bit Rate) . . . . . . . . . . . . . . . 434Table 365 externalNATIpAddress (External NAT IP Address) . . . . . . . . . . . . . . 435Table 366 farEndSctpSubnetIpAddress (Far End SCTP Subnet IP Address ) . . 436Table 367 farEndSctpSubnetMask (Far End SCTP Subnet Mask) . . . . . . . . . . . 437Table 368 minSCTPPort (Minimum SCTP port number) . . . . . . . . . . . . . . . . . . . 437Table 369 minUDPPort (Minimum UDP port number) . . . . . . . . . . . . . . . . . . . . . 438Table 370 signallingCommittedBitRate (Signalling Committed Bit Rate) . . . . . . . 439Table 371 tmparId (TMPAR Object Instance Identifier) . . . . . . . . . . . . . . . . . . . . 440Table 372 administrativeState (Administrative State) . . . . . . . . . . . . . . . . . . . . . 442Table 373 logMeanSyncValue (Log mean synchronization value) . . . . . . . . . . . 442Table 374 masterIpAddr (IP Address of the ToP master) . . . . . . . . . . . . . . . . . . 443Table 375 topId (Timing Over Packet Configuration Identifier) . . . . . . . . . . . . . . 444Table 376 atmTrafficDescriptorId (Traffic Descriptor Identifier) . . . . . . . . . . . . . . 446Table 377 conformanceDefinition (Conformance Definition) . . . . . . . . . . . . . . . . 446Table 378 minDesiredCellRate (Minimum Desired Cell Rate) . . . . . . . . . . . . . . . 447Table 379 peakCellRate (Peak Cell Rate) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 448Table 380 ubrShare (UBR Share) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 449Table 381 userLabel (User Label) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 450Table 382 administrativeState (Lock or unlock a TWAMP session) . . . . . . . . . . 452Table 383 destIpAddress (TWAMP session destination IP address) . . . . . . . . . 453Table 384 destPort (TWAMP session destination port) . . . . . . . . . . . . . . . . . . . . 453Table 385 dscp (DSCP value for TWAMP message transmission) . . . . . . . . . . . 454Table 386 messageSize (TWAMP initiator message size) . . . . . . . . . . . . . . . . . 455Table 387 plrAlarmThreshold (Packet loss ratio alarm threshold) . . . . . . . . . . . . 456Table 388 rttAlarmThreshold (Round-trip-time alarm threshold) . . . . . . . . . . . . . 457Table 389 sourceIpAddress (TWAMP initiator messages source IP address) . . 458Table 390 twampId (TWAMP session identifier) . . . . . . . . . . . . . . . . . . . . . . . . . 459Table 391 enableRP301Interface (Enable RP3-01 interface) . . . . . . . . . . . . . . . 461Table 392 unitId (Unit Identifier) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 461Table 393 unitTypeActual (Installed hardware unit type) . . . . . . . . . . . . . . . . . . . 462Table 394 unitTypeExpected (Expected hardware unit type) . . . . . . . . . . . . . . . 464
24 DN70577885
Flexi Transport Module Parameters
Id:0900d805809715d1Confidential
Table 395 VCI (Virtual Channel Identifier) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 467Table 396 VPI (Virtual Path Identifier) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 467Table 397 interfaceNumber (Interface Number) . . . . . . . . . . . . . . . . . . . . . . . . . . 468Table 398 trafficDescriptorId (Traffic Descriptor Pointer) . . . . . . . . . . . . . . . . . . . 469Table 399 unitNumber (Unit Number) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 470Table 400 vcCTPId (Virtual Channel Identifier (VCI)) . . . . . . . . . . . . . . . . . . . . . . 471Table 401 VCI (Virtual Channel Identifier) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 472Table 402 VPI (Virtual Path Identifier) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 472Table 403 aalProfilePtr (ATM Adaptation Layer (AAL) Profile Pointer) . . . . . . . . 473Table 404 interfaceNumber (Interface Number) . . . . . . . . . . . . . . . . . . . . . . . . . . 474Table 405 unitNumber (Unit Number) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 475Table 406 vcTTPId (Virtual Channel Trail Termination Point Identifier) . . . . . . . . 476Table 407 VPI (Virtual Path Identifier) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 478Table 408 interfaceNumber (Interface Number) . . . . . . . . . . . . . . . . . . . . . . . . . . 478Table 409 trafficDescriptorId (Traffic Descriptor Pointer) . . . . . . . . . . . . . . . . . . . 479Table 410 unitNumber (Unit Number) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 480Table 411 vpCTPId (Virtual Path Identifier (VPI)) . . . . . . . . . . . . . . . . . . . . . . . . . 481Table 412 VPI (Virtual Path Identifier) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 483Table 413 interfaceNumber (Interface Number) . . . . . . . . . . . . . . . . . . . . . . . . . . 483Table 414 unitNumber (Unit Number) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 484Table 415 vpTTPId (Virtual Path Trail Termination Point Identifier) . . . . . . . . . . . 485
DN70577885 25
Flexi Transport Module Parameters Summary of changes
Id:0900d80580975ffbConfidential
Summary of changesChanges between document issues are cumulative. Therefore, the latest document issue contains all changes made to previous issues.
Changes between issues 03H (2012-06-22, RU30)) and 03I (2012-10-19, RU30)IntroductionA note on BTS behavior when changing parameters using NetAct has been added.
Changed parameters
BFDbfdSourceUdpPort (UDP source port of the BFD session)
ETHLKadministrativeState (Administrative State)
linkOAMEnabled (Link OAM enabling flag)
Field 03H 03I
Description This parameter specifies the UDP source port to be used in the BFD session. Note: value range and default value depend on the BFD type. - For Multi Hop BFD, the value range is 4784, 49152...65535 and the default value = 4784. - For Single Hop BFD the value range is 3784, 49152...65535 and the default value = 3784.
This parameter specifies the UDP source port to be used in the BFD session. Note: value range and default value depend on the BFD type. - For Multi Hop BFD, the value range is 4784, 49152...65535 and the default value = 4784. - For Single Hop BFD the value range is 3784, 49152...65535 and the default value = 3784. NOTE: Service will be temporarily impacted because of modification of this parameter. Hence it is better not to modify this during peak hours.
Modification onLine cellShutdown
Field 03H 03I
Description This parameter is used to lock and unlock the interface. Locking the interface deactivates it and all alarms and any traffic over the interface is suppressed.
This parameter is used to lock and unlock the interface. Locking the interface deactivates it and all alarms and any traffic over the interface is suppressed. NOTE:Ethernet interface cannot be in use (unlocked) in the ATM Iub trans-port mode for FTFB, FTIF, and FIIF.
26 DN70577885
Flexi Transport Module Parameters
Id:0900d80580975ffbConfidential
Summary of changes
acceptableFrameTypes (Switch Port Acceptable Frame Types)
IPNOlinkOAMLoopbackSupport (Link OAM remote loopback discovery enabling flag)
Field 03H 03I
Description Enables the Link OAM functionality for this ethernet link. In consequence: - the values of all statistics counters of the Link OAM feature for this interface are set to 0 - the Link OAM alarms for this inter-face are cleared - the Link OAM discovery process is started, either in active or in passive mode. linkOAMEnabled cannot be set to FB bit pipe interfaces
Enables the Link OAM functionality for this ethernet link. In consequence: - the values of all statistics counters of the Link OAM feature for this interface are set to 0 - the Link OAM alarms for this inter-face are cleared - the Link OAM discovery process is started, either in active or in passive mode. linkOAMEnabled cannot be set to FB bit pipe interfaces NOTE:linkOAMEnabled flag cannot be value "true" in ATM Iub transport mode.
Field 03H 03I
Description If discardUntagged has value true, any untagged ingress frame is discarded. If discardUntagged has value false, any untagged ingress frame is assigned internally the default VLAN ID, i.e. the value of parameter defaultVlanId. If the interface on which the packet is to be transmitted contains the same VLAN id in its list of configured VLAN identifiers (parameter ETHLK - l2VlanIdList), the packet will indeed be transmitted via this interface, else it will be discarded.
If the value of acceptableFrameTypes is "AdmitTagged", the device will discard untagged and Priority-tagged frames received on this interface. If the value is “AdmitAll”, tagged, untagged and Priority-tagged frames received on this interface will be accepted. Untagged and Priority-tagged frames are assigned to the VLAN defined by the portDefaultVlanId for this interface.
Field 03H 03I
Description If set to true, the FTM enables the discov-ery process for Link OAM loopback requests initiated by a remote network element. If set to false, a loopback initi-ated from the remote network is not accepted by the FTM.
If set to true, the FTM enables the discov-ery process for Link OAM loopback requests initiated by a remote network element. If set to false, a loopback initi-ated from the remote network is not accepted by the FTM. NOTE: linkOAMLoopbackSupport flag cannot be "true" in ATM Iub transport mode.
DN70577885 27
Flexi Transport Module Parameters Summary of changes
Id:0900d80580975ffbConfidential
IPRMRmExceptions/sourceTwoIpAddr (IP address for source two)
RmExceptions/sourceTwoNetMask (IP Subnet Mask)
RmExceptions (Restricted Mode Exception)
Field 03H 03I
Description This parameter is meaningful if and only if source two is defined as SINGLE or as RANGE; in all other cases it is ignored. "IP address source two" specifies a single IP address. If source two is defined as SINGLE, this is the only allowed IP address. If source two is defined as RANGE, then the allowed range of IP addresses is obtained by applying the "IP subnet mask for source two" to this IP address. The IP address must be given as "dotted decimal" string.
This parameter is meaningful if and only if source two is defined as SINGLE or as RANGE; in all other cases it is ignored. "IP address source two" specifies a single IP address. If source two is defined as SINGLE, this is the only allowed IP address. If source two is defined as RANGE, then the allowed range of IP addresses is obtained by applying the "IP subnet mask for source two" to this IP address. The IP address must be given as "dotted decimal" string. NOTE: IP address 0.0.0.0 is not allowed.
Field 03H 03I
Description This parameter is meaningful if and only if source two is defined as RANGE; in all other cases it is ignored. "IP Subnet Mask" specifies a netmask which, when applied to "IP address for source two" yields the allowed range of far end IP addresses. The netmask must be entered in dotted decimal format.
This parameter is meaningful if and only if source two is defined as RANGE; in all other cases it is ignored. "IP Subnet Mask" specifies a netmask which, when applied to "IP address for source two" yields the allowed range of far end IP addresses. The netmask must be entered in dotted decimal format. NOTE:IP address 255.255.255.255 and 0.0.0.0 are not allowed.
28 DN70577885
Flexi Transport Module Parameters
Id:0900d80580975ffbConfidential
Summary of changes
RmExceptions/userLabel (User Label)
IPRTipRoutingTableId (IP Routing Table Identifier)
Field 03H 03I
Description Restricted mode provides protection of the mobile carriers' network against intru-sion through interfaces of the Base Station, in particular the LMT. By default, all traffic to other destinations will be barred. IPRM allows to configure exceptions, so that defined IP traffic will be allowed, for example communication with an LDAP server or administration of other base stations through the LMP of the local one. Administration of the Restricted Mode consists therefore in defining exceptions from the general blocking of traffic to the outside world. An RM exception is defined as a far end IP address to/from which traffic is allowed. Port information is not taken into account. It is possible to define up to 32 excep-tions.
Restricted mode provides protection of the mobile carriers' network against intru-sion through interfaces of the Base Station, in particular the LMT. By default, all traffic to other destinations will be barred. IPRM allows to configure exceptions, so that defined IP traffic will be allowed, for example communication with an LDAP server or administration of other base stations through the LMP of the local one. Administration of the Restricted Mode consists therefore in defining exceptions from the general blocking of traffic to the outside world. An RM exception is defined as a far end IP address to/from which traffic is allowed. Port information is not taken into account. It is possible to define up to 32 excep-tions. NOTE:Exceptions can overlap but they cannot have exactly same configu-ration.
Field 03H 03I
Description An alphanumeric string asigned by the user to uniquely identify the RM Excep-tion. (More exactly: only the pair user-Label/sourceOne must be unique)
An alphanumeric string asigned by the user to uniquely identify the RM Excep-tion. (More exactly: only the pair user-Label/sourceOne must be unique) NOTE:This parameter is a man-datory parameter for exception and it must be unique.
DN70577885 29
Flexi Transport Module Parameters Summary of changes
Id:0900d80580975ffbConfidential
OAMMEPaisTxPeriod (AIS messages period)
OAMPRFloopBackTime (Link OAM loopback duration)
Field 03H 03I
Description This parameter identifies an IP routing table of the BTS. Instance 1 shall only be used for DCN routing, instance 2 shall be used for IP routing. IPRT-1 is not supported in IubIP. "FTEB, FTHA, FTPB, FTFA, FTFB, FTIF and FIIF" are not supported for IPRT-2 in AtmIub mode. "FSM and FSI" are sup-ported for IPRT-2 only in IubIP mode.
This parameter identifies an IP routing table of the BTS. Instance 1 shall only be used for DCN routing, instance 2 shall be used for IP routing. IPRT-1 is not supported in IubIP. "FTEB, FTHA, FTPB, FTFA, FTFB, FTIF and FIIF" are not supported for IPRT-2 in AtmIub mode. "FSM and FSI" are sup-ported for IPRT-2 only in IubIP mode. NOTE: The routing options should be hidden in IP connectivity test dialog for FTFB,FTIF & FIIF in ATM Iub mode and DCN routing shall be used for test in these 3 units when mode is ATM Iub.
Field 03H 03I
Full Name AIS messages transmission period AIS messages period
30 DN70577885
Flexi Transport Module Parameters
Id:0900d80580975ffbConfidential
Summary of changes
OSPFV2ospfRouterId (OSPF router identification)
Field 03H 03I
Description This parameter specifies the duration of a loopback operation initiated by the FTM. The parameter is only relevant in Link OAM active mode.
This timer is relevant for Loopback mode either initiated by the BTS or initiated by the Peer. When BTS initiates the Loopback mode (remote end is in looped state), the loopback time defines the maximum duration of the loopback. After expiry of this timer ("timeout"), the BTS will termi-nate the Loopback by sending a Loopback Control Disable PDU to the Peer. When the peer initiates the Loopback mode(BTS is in looped state), the BTS receives a Loopback Control Enable PDU from the Peer and sends an Infor-mation PDU back including updated state information. The Loopback mode will be exited if one of the following conditions apply: (i) The peer sends a Loopback Control Disable PDU to the BTS within the loopback timeout timer (ii)The loopback timeout timer expires and the BTS exists the loopback mode by sending an Information OAM PDU to the peer including updated state information. This case is not standard-ized, but it has been included to avoid the BTS remaining in Loopback mode forever, in case the remote end does not send a Control Disable PDU or it gets lost.
DN70577885 31
Flexi Transport Module Parameters Summary of changes
Id:0900d80580975ffbConfidential
confPref (OSPF routing preference value)
STPGsynchERegenOn (Activate the synchronous ethernet regenerator function)
synchroSourceList/clockProtocol (Protocol of the clock source)
Field 03H 03I
Description This parameter identifies the OSPF router through an IP address. If the operator sets the parameter to 0.0.0.0 the FTM will overwrite the value as follows: - with the highest configured virtual IP address in the applications binding map of the IPNO class - if none of the IP addresses of that map is a virtual IP address, the FTM shall overwrite the parameter with the highest network interface IP address.
This parameter identifies the OSPF router through an IP address. If the operator sets the parameter to 0.0.0.0 the FTM will overwrite the value as follows: - with the highest configured virtual IP address in the applications binding map of the IPNO class - if none of the IP addresses of that map is a virtual IP address, the FTM shall overwrite the parameter with the highest network interface IP address. NOTE: Any change to this parameter causes OSPF daemon restart. It may cause temporary connectivity loss depending on routing configuration.
Field 03H 03I
Description This parameter specifies the preference value of the OSPF protocol. The prefer-ence value is used in calculating the cost of an OSPF based route.
This parameter specifies the preference value of the OSPF protocol. The prefer-ence value is used in calculating the cost of an OSPF based route. NOTE: Any change to this parameter causes OSPF daemon restart. It may cause temporary connectivity loss depending on routing configuration.
Field 03H 03I
Description This parameter switches the Synchro-nous Ethernet Regenerator function on.
This parameter switches the Synchro-nous Ethernet Regenerator function on. NOTE: This parameter should not be allowed to be set to true in ATM Iub mode for FTFB,FTIF & FIIF.
32 DN70577885
Flexi Transport Module Parameters
Id:0900d80580975ffbConfidential
Summary of changes
synchroSourceList/ssmAcceptanceLevel (SSM defined value)
synchroSourceList (The synchronization sources of the BTS)
Changes between issues 03G (2012-04-24, RU30) and 03H (2012-06-22, RU30)Changed parameters
ETHLKmacAddr (MAC address)
speedAndDuplex (Speed and Duplex flag)
Field 03H 03I
Description This parameter holds the protocol of this clock source: PDH, SDH, synchronuous Ethernet, Timing over Packet or the external 2 MHz clock.
This parameter holds the protocol of this clock source: PDH, SDH, synchronuous Ethernet, Timing over Packet or the external 2 MHz clock. Note: SyncE and TOP source does not support unit types FTFB, FTIF and FIIF when transport mode is Atm Iub
Field 03H 03I
Default value 1
Field 03H 03I
Description This is the list of synchronization sources of the BTS. Up to 2 clock sources can be configured.
This is the list of synchronization sources of the BTS. Up to 2 clock sources can be configured. NOTE:Synchronous Ethernet syn-chronization source is not supported in the FTFB, FTIF, FIIF unit when it's in the ATM Iub transport.
Field 03G 03H
Interfaces FTM->EM, FTM->RAC, RAC<->RACApp FTM->EM, FTM->RAC
DN70577885 33
Flexi Transport Module Parameters Summary of changes
Id:0900d80580975ffbConfidential
portDefaultVlanId (Switch Port Default VLAN Identifier)
FTMsoftwareReleaseVersion (Software Release Version)
IEIFmtu (Maximum transfer unit)
Field 03G 03H
Description This parameter specificies if link charac-teristics are autonegotiated or not. If not, the attribute contains the capacity and the duplex mode to be set forcibly. Note that 1000 MBit is available only on Gigabit Ethernet interfaces (GE). This parameter is not applied for the FlexBus interfaces of the FTFB hardware unit (interfaces 3 and 4 of the FTFB unit). For these interfaces the capacity and traffic mode is not configurable by the management system.
This parameter specificies if link charac-teristics are autonegotiated or not. If not, the attribute contains the capacity and the duplex mode to be set forcibly. Note that 1000 MBit is available only on Gigabit Ethernet interfaces (GE). This parameter is not applied for the FlexBus interfaces of the FTFB hardware unit (interfaces 3 and 4 of the FTFB unit). For these interfaces the capacity and traffic mode is not configurable by the management system. NOTE: With FSM-EIF2 / FSI-EIF5, AUTODETECT and Forced 1000Mbits are supported.
Field 03G 03H
Description This parameter specifies the VLAN iden-tifier that is inserted internally by the FTM into an untagged ingress frame that enters the layer 2 switch via this Ethernet interface - if parameter discardUntagged has value false for the Ethernet interface. In order that the frame will be trans-mitted via the same or another Ethernet interface, after layer 2 switching has been performed, the same VLAN id must be configured in the VLAN identifier list of that Ethernet interface (see parameter l2VlanIdList). Else the frame will be dis-carded.
This parameter specifies the VLAN iden-tifier that is inserted internally by the FTM into an untagged ingress frame that enters the layer 2 switch via this Ethernet interface - if parameter discardUntagged has value false for the Ethernet interface. In order that the frame will be trans-mitted via the same or another Ethernet interface, after layer 2 switching has been performed, the same VLAN id must be configured in the VLAN identifier list of that Ethernet interface (see parameter l2VlanIdList). Else the frame will be dis-carded. Default VLAN id cannot be configured as a part of interface's configured VLAN id list.
Field 03G 03H
Interfaces FTM->EM, FTM->RAC, RAC<->RACApp FTM->EM, FTM->RAC
34 DN70577885
Flexi Transport Module Parameters
Id:0900d80580975ffbConfidential
Summary of changes
upperLayerShaping (Upper Layer Shaping Enabled Flag)
IPNObtsIpAddr (Base Station IP Address)
twampReflectorOn (TWAMP message response enabling flag)
STPGsynchroSourceList/clockProtocol (Protocol of the clock source)
UNITunitTypeActual (Installed hardware unit type)
Removed parametersOAMPRF
• enableCcm (Allow sending of CCM messages and reset CCM counters)
Changes between issues 03F (2011-12-16, RU30) and 03G (2012-04-24, RU30)New parameters
Field 03G 03H
Interfaces FTM->EM, FTM->RAC, RAC<->RACApp FTM->EM, FTM->RAC
Field 03G 03H
Default value true
Default value notes By default the ethernet shaping should be disabled.
Field 03G 03H
Description IP Address of the Base Station. Address under which the Base Station is available remotely.
IP Address of the Base Station. Address under which the Base Station is available remotely. FSMr3 is not configurable on this parameter.
Field 03G 03H
Default value notes By default the TWAMP reflector is switched on.
Field 03G 03H
Range and step 1 (clkPDH), 2 (clkSDH), 3 (clkSyncE), 4 (clkToP), 5 (clkExt)
1 (clkPDH), 2 (clkSDH), 3 (clkSyncE), 4 (clkToP)
Field 03G 03H
Interfaces FTM->EM, FTM->RAC, RAC<->RACApp FTM->EM, FTM->RAC
DN70577885 35
Flexi Transport Module Parameters Summary of changes
Id:0900d80580975ffbConfidential
IEIFmtuMismatchDetection (MTU mismatch detection in use)
IVIFmtuMismatchDetection (MTU mismatch detection in use)
OAMPRFlinkOAMProfileName (Link OAM Profile Name)
Changed parameters
BFDbfdGrp (BFD group reference)
bfdActivation (BFD session activation flag)
bfdAdminUp (BFD session admin down state control)
Description If set to true, this parameter enables OSPF MTU mismatch detection on receiving DBD (Data Base Descriptor) packets on this interface.
Related features RAN1879 Dynamic routing by OSPF (optional)
Description If set to true, this parameter enables OSPF MTU mismatch detection on receiving DBD (Data Base Descriptor) packets on this interface.
Related features RAN1879 Dynamic routing by OSPF (optional)
Description This parameter describes a unique configurable name for each link OAM profile.
Related features RAN1880-a Ethernet OAM (Ethernet Link OAM) (optional)
Field 03F 03G
Related parameters iHSPAmode of IPNO - Not supported in case parameter iHSPAmode is set to enabled.
function of BFD - "bfdGrp" parameter shall not be configured (must be left empty) when "function" parameter has value OSPF_ALL or OSPF_IP_IF
function of BFD - "bfdGrp" parameter shall not be configured (must be left empty) when "function" parameter has value OSPF_ALL or OSPF_IP_IF
Field 03F 03G
Related parameters iHSPAmode of IPNO - Not supported in case parameter iHSPAmode is set to enabled.
function of BFD - This parameter is ignored when the value of "function" parameter is OSPF_ALL or OSPF_IP_IF.
function of BFD - This parameter is ignored when the value of "function" parameter is OSPF_ALL or OSPF_IP_IF.
36 DN70577885
Flexi Transport Module Parameters
Id:0900d80580975ffbConfidential
Summary of changes
function (BFD session function definition)
bfdId (BFD session identifier)
bfdDetectMult (BFD session packets lost detection time multiplier)
bfdType (BFD session type
desMinTxInt (Desired minimum BFD control word transmit interval)
Field 03F 03G
Related parameters bfdActivation of BFD - Parameter bfdAd-minUp is only relevant if parameter bfdActivation has value true.
iHSPAmode of IPNO - Not supported in case parameter iHSPAmode is set to enabled.
Field 03F 03G
Related parameters iHSPAmode of IPNO - Not supported in case parameter iHSPAmode is set to enabled.
unitTypeExpected of UNIT - Since OSPF is not supported on all HW variants, for the HW modules FTEB, FTHA, FTPB, FTFA the only supported value is "MANUAL_BFD_SESSION".
unitTypeExpected of UNIT - Since OSPF is not supported on all HW variants, for the HW modules FTEB, FTHA, FTPB, FTFA the only supported value is "MANUAL_BFD_SESSION".
Field 03F 03G
Related parameters iHSPAmode of IPNO - Not supported in case parameter iHSPAmode is set to enabled.
Field 03F 03G
Related parameters iHSPAmode of IPNO - Not supported in case parameter iHSPAmode is set to enabled.
Field 03F 03G
Related parameters iHSPAmode of IPNO - Not supported in case parameter iHSPAmode is set to enabled.
DN70577885 37
Flexi Transport Module Parameters Summary of changes
Id:0900d80580975ffbConfidential
bfdDestAddress (Destination IP address for the BFD session)
reqMinRxInt (Required minimum BFD control word receive interval)
bfdSourceIpAddr (Source IP address for the BFD session)
bfdSourceUdpPort (UDP source port of the BFD session)
CESIFcesifId (CES over PSN interface identifier)
Field 03F 03G
Related parameters iHSPAmode of IPNO - Not supported in case parameter iHSPAmode is set to enabled.
Field 03F 03G
Related parameters iHSPAmode of IPNO - Not supported in case parameter iHSPAmode is set to enabled.
Field 03F 03G
Related parameters iHSPAmode of IPNO - Not supported in case parameter iHSPAmode is set to enabled.
Field 03F 03G
Related parameters iHSPAmode of IPNO - Not supported in case parameter iHSPAmode is set to enabled.
Field 03F 03G
Related parameters bfdType of BFD - - For Multi Hop BFD, the value range is 4784, 49152...65535 and the default value = 4784. - For Single Hop BFD the value range is 3784, 49152...65535 and the default value = 3784.
iHSPAmode of IPNO - Not supported in case parameter iHSPAmode is set to enabled.
bfdType of BFD - - For Multi Hop BFD, the value range is 4784, 49152...65535 and the default value = 4784. - For Single Hop BFD the value range is 3784, 49152...65535 and the default value = 3784.
38 DN70577885
Flexi Transport Module Parameters
Id:0900d80580975ffbConfidential
Summary of changes
cesMinUDPPort (CES over PSN source port value range)
CESPWadministrativeState (Administrative state)
cesPWid (CES over PSN Pseudowire Identifier)
dscp (DSCP value)
jitterBufferSize (Jitter Buffer Size)
Field 03F 03G
Related parameters iHSPAmode of IPNO - Not supported in case parameter iHSPAmode is set to enabled.
Field 03F 03G
Related parameters iHSPAmode of IPNO - Not supported in case parameter iHSPAmode is set to enabled.
Field 03F 03G
Related parameters iHSPAmode of IPNO - Not supported in case parameter iHSPAmode is set to enabled.
administrativeState of P3SL - The features CES over PSN and Multi Link PPP cannot be operated together.
administrativeState of P3ML - The features CES over PSN and Multi Link PPP cannot be operated together.
administrativeState of P3SL - The features CES over PSN and Multi Link PPP cannot be operated together.
administrativeState of P3ML - The features CES over PSN and Multi Link PPP cannot be operated together.
Field 03F 03G
Multiplicity 16 1
Related parameters iHSPAmode of IPNO - Not supported in case parameter iHSPAmode is set to enabled.
Field 03F 03G
Related parameters iHSPAmode of IPNO - Not supported in case parameter iHSPAmode is set to enabled.
DN70577885 39
Flexi Transport Module Parameters Summary of changes
Id:0900d80580975ffbConfidential
framesNumber (Number of frames per CESoPSN packet)
payloadTimeslots (Payload timeslots of TDM frame)
remoteUDPPort (Remote UDP port number for CES over PSN)
CESPWTcesPWTid (CES over PSN pseudowire tunnel identifier)
Field 03F 03G
Related parameters iHSPAmode of IPNO - Not supported in case parameter iHSPAmode is set to enabled.
Field 03F 03G
Related parameters payloadTimeslots of CESPW - The number of frames per packet multiplied by the number of PDH timeslots (param-eter payloadTimeslots) shall be between 40 and 1536. Otherwise the resulting CESoPSN packet size is violating the allowed ethernet packet size and the CES connection cannot be established.
iHSPAmode of IPNO - Not supported in case parameter iHSPAmode is set to enabled.
payloadTimeslots of CESPW - The number of frames per packet multiplied by the number of PDH timeslots (param-eter payloadTimeslots) shall be between 40 and 1536. Otherwise the resulting CESoPSN packet size is violating the allowed ethernet packet size and the CES connection cannot be established.
Field 03F 03G
Related parameters framesNumber of CESPW - The number of timeslots multiplied by the number of frames per packet (parameter fra-mesNumber) shall be between 40 and 1536. Otherwise the resulting CESoPSN packet size is violating the allowed ethernet packet size and the CES con-nection cannot be established.
iHSPAmode of IPNO - Not supported in case parameter iHSPAmode is set to enabled.
framesNumber of CESPW - The number of timeslots multiplied by the number of frames per packet (parameter fra-mesNumber) shall be between 40 and 1536. Otherwise the resulting CESoPSN packet size is violating the allowed ethernet packet size and the CES con-nection cannot be established.
Field 03F 03G
Related parameters iHSPAmode of IPNO - Not supported in case parameter iHSPAmode is set to enabled.
40 DN70577885
Flexi Transport Module Parameters
Id:0900d80580975ffbConfidential
Summary of changes
destIpAddress (Destination IP address)
ETHLKlinkOAMEnabled (Link OAM enabling flag)
linkOAMProfile (Link OAM profile reference)
acceptableFrameTypes (Switch Port Acceptable Frame Types)
portDefaultVlanId (Switch Port Default VLAN Identifier)
Field 03F 03G
Related parameters iHSPAmode of IPNO - Not supported in case parameter iHSPAmode is set to enabled.
Field 03F 03G
Related parameters iHSPAmode of IPNO - Not supported in case parameter iHSPAmode is set to enabled.
Field 03F 03G
Related parameters iHSPAmode of IPNO - Not supported in case parameter iHSPAmode is set to enabled.
linkOAMProfile of ETHLK - The value of linkOAMEnabled shall only be set to true, if the value of linkOAMProfile is not the empty string but references an existing instance of object class OAMPRF.
iHSPAmode of IPNO - This parameter is not supported when iHSPAmode is set to enabled.
linkOAMProfile of ETHLK - The value of linkOAMEnabled shall only be set to true, if the value of linkOAMProfile is not the empty string but references an existing instance of object class OAMPRF.
Field 03F 03G
Related parameters iHSPAmode of IPNO - Not supported in case parameter iHSPAmode is set to enabled.
iHSPAmode of IPNO - This parameter is not supported when iHSPAmode is set to enabled.
Field 03F 03G
Related parameters iHSPAmode of IPNO - Not supported in case parameter iHSPAmode is set to enabled.
DN70577885 41
Flexi Transport Module Parameters Summary of changes
Id:0900d80580975ffbConfidential
portDefaultPriority (Switch Port Default VLAN Priority)
l2BurstSize (Switch Port egress Shaper Burst Size)
l2ShaperRate (Switch Port egress Shaper Rate)
Field 03F 03G
Related parameters iHSPAmode of IPNO - Not supported in case parameter iHSPAmode is set to enabled.
enableLayer2Switching of L2SWI - VLAN aware switching mode should be enabled (enableLayer2Switching="true")
enableLayer2Switching of L2SWI - VLAN aware switching mode should be enabled (enableLayer2Switching="true")
Field 03F 03G
Related parameters iHSPAmode of IPNO - Not supported in case parameter iHSPAmode is set to enabled.
enableLayer2Switching of L2SWI - VLAN aware switching mode should be enabled (enableLayer2Switching="true")
enableLayer2Switching of L2SWI - VLAN aware switching mode should be enabled (enableLayer2Switching="true")
Field 03F 03G
Description This parameter specifies the maximum burst size that can be transmitted in a single burst in egress direction on this Ethernet interface of layer 2 switch. The burst size is actually calculated by < l2ShaperRate x l2BurstSize x 1sec >. Example: l2ShaperRate =100 Mb/s and l2BurstSize=1% results in a burst size of 1 Mbit = 125 Kbyte. This parameter is valid only for FTLB.
This parameter specifies the maximum burst size that can be transmitted in a single burst in egress direction on this Ethernet interface of layer 2 switch. The parameter value expresses a proportion of 0.1% of the related shaper-rate per step. The burst size is actually calculated by < l2ShaperRate x l2BurstSize x 1sec >. Example: l2ShaperRate =100 [ 1 Mbit/s] and l2BurstSize=10 [ 0.1 %] results in a burst size of 100 Mbit/s x 10 x 0.1 x 1/100 x 1s = 1 Mbit = 125 Kbyte.. This parameter is valid only for FTLB.
Related parameters iHSPAmode of IPNO - Not supported in case parameter iHSPAmode is set to enabled.
Field 03F 03G
Related parameters iHSPAmode of IPNO - Not supported in case parameter iHSPAmode is set to enabled.
42 DN70577885
Flexi Transport Module Parameters
Id:0900d80580975ffbConfidential
Summary of changes
l2IngressRate (Switch Port ingress RateLimiter Rate )
l2VlanIdList (Switch Port VLAN Member List)
l2VlanIdList/highValue (Switch Port VLAN Member Range High Value)
l2VlanIdList/lowValue (Switch Port VLAN Member Range Low Value)
IEIFipAddr/netmask (IP Network Mask)
proxyArpIpAddrList (List of proxy ARP IP addresses for this interface.)
ipAddr/localIpAddr (Local Address of the IP Interface)
Field 03F 03G
Related parameters iHSPAmode of IPNO - Not supported in case parameter iHSPAmode is set to enabled.
Field 03F 03G
Related parameters iHSPAmode of IPNO - Not supported in case parameter iHSPAmode is set to enabled.
Field 03F 03G
Related parameters iHSPAmode of IPNO - Not supported in case parameter iHSPAmode is set to enabled.
Field 03F 03G
Default value 1
Default value notes Default value means "untagged".
Related parameters iHSPAmode of IPNO - Not supported in case parameter iHSPAmode is set to enabled.
Field 03F 03G
Related parameters iHSPAmode of IPNO - Not supported in case parameter iHSPAmode is set to enabled.
Field 03F 03G
Related parameters iHSPAmode of IPNO - Not supported in case parameter iHSPAmode is set to enabled.
DN70577885 43
Flexi Transport Module Parameters Summary of changes
Id:0900d80580975ffbConfidential
confCost (OSPF configured interface cost)
interfaceArea (OSPF interface area)
helloInterval (OSPF keepalive message transmission interval)
retransInterval (OSPF LSA retransmission interval)
transmitDelay (OSPF packet transmission delay)
routerDeadInterval (OSPF router read interval)
Field 03F 03G
Related parameters iHSPAmode of IPNO - Not supported in case parameter iHSPAmode is set to enabled.
Field 03F 03G
Related parameters iHSPAmode of IPNO - Not supported in case parameter iHSPAmode is set to enabled.
Field 03F 03G
Related parameters iHSPAmode of IPNO - Not supported in case parameter iHSPAmode is set to enabled.
Field 03F 03G
Related parameters iHSPAmode of IPNO - Not supported in case parameter iHSPAmode is set to enabled.
routerDeadInterval of IEIF - Router dead interval should be greater than hello interval
routerDeadInterval of IEIF - Router dead interval should be greater than hello interval
Field 03F 03G
Related parameters iHSPAmode of IPNO - Not supported in case parameter iHSPAmode is set to enabled.
Field 03F 03G
Related parameters iHSPAmode of IPNO - Not supported in case parameter iHSPAmode is set to enabled.
44 DN70577885
Flexi Transport Module Parameters
Id:0900d80580975ffbConfidential
Summary of changes
ospfWithBfd (OSPF uses additionally BFD)
sbs (Shaper burst size)
sir (Shaper information rate)
Field 03F 03G
Related parameters iHSPAmode of IPNO - Not supported in case parameter iHSPAmode is set to enabled.
helloInterval of IEIF - Router dead interval should be greater than hello interval
helloInterval of IEIF - Router dead interval should be greater than hello interval
Field 03F 03G
Related parameters iHSPAmode of IPNO - In iHSPAmode only ManualBfdSession is supported.
Field 03F 03G
Related parameters localIpAddr of IEIF - Parameter sbs is only relevant in case the interface is in use, i.e. in case the localIpAddr is differ-ent from 0.0.0.0.
trafficPathShapingEnable of IEIF - Parameter sbs is only relevant in case parameter trafficPathShapingEnable has value TPS_PATH.
iHSPAmode of IPNO - Not supported in case parameter iHSPAmode is set to enabled.
localIpAddr of IEIF - Parameter sbs is only relevant in case the interface is in use, i.e. in case the localIpAddr is differ-ent from 0.0.0.0.
trafficPathShapingEnable of IEIF - Parameter sbs is only relevant in case parameter trafficPathShapingEnable has value TPS_PATH.
Field 03F 03G
Description This parameter holds the shaper informa-tion rate for the interface. The maximum value of this parame-ter is 100 MBps for Fast Ethernet inter-faces and 1 GBps for Gigabit Ethernet interfaces.
This parameter holds the shaper informa-tion rate for the interface. The maximum value of this parame-ter is 100 MBps for Fast Ethernet inter-faces and 1 GBps for Gigabit Ethernet interfaces. For FTLB, the actual minimum egress rate is 1.18 Mbps and on FSM-r3, the actual minimum egress rate is 1.56 Mbps due to technical limitations on Octeon.
DN70577885 45
Flexi Transport Module Parameters Summary of changes
Id:0900d80580975ffbConfidential
sbsTotal (Total shaper burst size)
sirTotal (Total shaper information rate)
trafficPathShapingEnable (Traffic path shaping enabling flag)
Related parameters localIpAddr of IEIF - Parameter sir is only relevant in case the interface is in use, i.e. in case the localIpAddr is different from 0.0.0.0.
trafficPathShapingEnable of IEIF - Parameter sir is only relevant in case parameter trafficPathShapingEnable has value TPS_PATH.
iHSPAmode of IPNO - Not supported in case parameter iHSPAmode is set to enabled.
localIpAddr of IEIF - Parameter sir is only relevant in case the interface is in use, i.e. in case the localIpAddr is different from 0.0.0.0.
trafficPathShapingEnable of IEIF - Parameter sir is only relevant in case parameter trafficPathShapingEnable has value TPS_PATH.
Field 03F 03G
Field 03F 03G
Related parameters trafficPathShapingEnable of IEIF - Parameter sbsTotal is only relevant in case parameter trafficPathShapingEn-able has value TPS_WFQ.
iHSPAmode of IPNO - Not supported in case parameter iHSPAmode is set to enabled.
trafficPathShapingEnable of IEIF - Parameter sbsTotal is only relevant in case parameter trafficPathShapingEn-able has value TPS_WFQ.
Field 03F 03G
Related parameters trafficPathShapingEnable of IEIF - Parameter sirTotal is only relevant in case parameter trafficPathShapingEn-able has value TPS_WFQ.
iHSPAmode of IPNO - Not supported in case parameter iHSPAmode is set to enabled.
trafficPathShapingEnable of IEIF - Parameter sirTotal is only relevant in case parameter trafficPathShapingEn-able has value TPS_WFQ.
46 DN70577885
Flexi Transport Module Parameters
Id:0900d80580975ffbConfidential
Summary of changes
vlanEnabled (Vlan Enabled flag)
vlanId (Vlan ID)
IPNOcesopsnIpAddress (CES over PSN application IP address)
Field 03F 03G
Related parameters shapedBandwidth of IEIF - Transport Ethernet interface bandwidth available is dependent on this param (see IEIF/shapedBandwidth and IEIF/sis-Tota;l).
sirTotal of IEIF - Transport Ethernet inter-face bandwidth available is dependent on this param (see IEIF/shapedBandwidth and IEIF/sisTotal).
iHSPAmode of IPNO - Not supported in case parameter iHSPAmode is set to enabled.
shapedBandwidth of IEIF - Transport Ethernet interface bandwidth available is dependent on this param (see IEIF/shapedBandwidth and IEIF/sis-Tota;l).
sirTotal of IEIF - Transport Ethernet inter-face bandwidth available is dependent on this param (see IEIF/shapedBandwidth and IEIF/sisTotal).
Field 03F 03G
Related parameters iHSPAmode of IPNO - Not supported in case parameter iHSPAmode is set to enabled.
Field 03F 03G
Related parameters vlanEnabled of IEIF -
iHSPAmode of IPNO - Not supported in case parameter iHSPAmode is set to enabled.
vlanEnabled of IEIF -
DN70577885 47
Flexi Transport Module Parameters Summary of changes
Id:0900d80580975ffbConfidential
oamCir (Committed information rate for Service OAM messages)
fpLocalUdpPort (Local UDP port for small packets multiplexing)
mPlaneIpAddress (Management -plane application IP address)
fpMuxAmount (Maximum amount of small packets that can be multiplexed)
Field 03F 03G
Related parameters transportMode of IPNO - Parameter cesopsnIpAddress is irrelevant in case parameter transportMode has value AtmOverEthernet and in case parameter transportMode has value DualIub.
administrativeState of P3SL - Parameter cesopsnIpAddress is irrelevant in case parameter administrativeState has value unlocked.
administrativeState of P3ML - Parameter cesopsnIpAddress is irrelevant in case parameter administrativeState has value unlocked.
transportMode of IPNO - Parameter cesopsnIpAddress is irrelevant in case parameter transportMode has value AtmOverEthernet and in case parameter transportMode has value DualIub.
iHSPAmode of IPNO - Not supported in case parameter iHSPAmode is set to enabled.
administrativeState of P3SL - Parameter cesopsnIpAddress is irrelevant in case parameter administrativeState has value unlocked.
administrativeState of P3ML - Parameter cesopsnIpAddress is irrelevant in case parameter administrativeState has value unlocked.
Field 03F 03G
Related parameters iHSPAmode of IPNO - Not supported in case parameter iHSPAmode is set to enabled.
Field 03F 03G
Related parameters iHSPAmode of IPNO - Not supported in case parameter iHSPAmode is set to enabled.
Field 03F 03G
Related parameters iHSPAmode of IPNO - Not supported in case parameter iHSPAmode is set to enabled.
Field 03F 03G
Related parameters iHSPAmode of IPNO - Not supported in case parameter iHSPAmode is set to enabled.
48 DN70577885
Flexi Transport Module Parameters
Id:0900d80580975ffbConfidential
Summary of changes
oamTlvReply (Optional TLV message reply flag)
fpRemoteUdpPort (Remote UDP port for small packets multiplexing)
fpMuxDelay (Small packets multiplexing delay time)
IPRTstaticRoutes (List of static routes)
staticRoutes/preference (Preference value for the route)
IVIFcESoPSN (CES over PSN flag)
proxyArpIpAddrList (List of proxy ARP IP addresses for this interface.)
Field 03F 03G
Related parameters iHSPAmode of IPNO - Not supported in case parameter iHSPAmode is set to enabled.
Field 03F 03G
Related parameters iHSPAmode of IPNO - Not supported in case parameter iHSPAmode is set to enabled.
Field 03F 03G
Related parameters iHSPAmode of IPNO - Not supported in case parameter iHSPAmode is set to enabled.
Field 03F 03G
Multiplicity 32 100
Field 03F 03G
Related parameters iHSPAmode of IPNO - Not supported in case parameter iHSPAmode is set to enabled.
Field 03F 03G
Related parameters iHSPAmode of IPNO - Not supported in case parameter iHSPAmode is set to enabled.
DN70577885 49
Flexi Transport Module Parameters Summary of changes
Id:0900d80580975ffbConfidential
confCost (OSPF configured interface cost)
interfaceArea (OSPF interface area)
retransInterval (OSPF LSA retransmission interval)
transmitDelay (OSPF packet transmission delay)
routerDeadInterval (OSPF router read interval)
ospfWithBfd (OSPF uses additionally BFD)
Field 03F 03G
Related parameters iHSPAmode of IPNO - Not supported in case parameter iHSPAmode is set to enabled.
Field 03F 03G
Related parameters iHSPAmode of IPNO - Not supported in case parameter iHSPAmode is set to enabled.
Field 03F 03G
Related parameters iHSPAmode of IPNO - Not supported in case parameter iHSPAmode is set to enabled.
Field 03F 03G
Related parameters iHSPAmode of IPNO - Not supported in case parameter iHSPAmode is set to enabled.
Field 03F 03G
Related parameters iHSPAmode of IPNO - Not supported in case parameter iHSPAmode is set to enabled.
Field 03F 03G
Related parameters iHSPAmode of IPNO - Not supported in case parameter iHSPAmode is set to enabled.
helloInterval of IVIF - Router dead interval should be greater than hello interval
helloInterval of IVIF - Router dead interval should be greater than hello interval
50 DN70577885
Flexi Transport Module Parameters
Id:0900d80580975ffbConfidential
Summary of changes
sir (Shaper information rate)
L2SWIdscpMap (DSCP to priority queue map)
dscpMap/dscp (DSCP value)
enableLayer2Switching (Ethernet Switch Enable)
l2PriorityQueueWeight2 (Layer 2 switch member weight for priority queue 2)
Field 03F 03G
Related parameters iHSPAmode of IPNO - In iHSPAmode only ManualBfdSession is supported.
Field 03F 03G
Description The Shaper Information Rate ("VLAN SIR") defines the bandwidth limit to which VLAN traffic is shaped by the traffic path shaper. Note: The SIRs should be configured to equal the sum of CIR+EIR at the corre-sponding UNI. The sum of all SIRs is allowed to exceed the total available bandwidth on the interface (overbooking). Therefore, SIR cannot be guaranteed by the system.
The Shaper Information Rate ("VLAN SIR") defines the bandwidth limit to which VLAN traffic is shaped by the traffic path shaper. For FTLB, the actual minimum egress rate is 1.18 Mbps and on FSM-r3, the actual minimum egress rate is 1.56 Mbps due to technical limitations on Octeon. Note: The SIRs should be configured to equal the sum of CIR+EIR at the corre-sponding UNI. The sum of all SIRs is allowed to exceed the total available bandwidth on the interface (overbooking). Therefore, SIR cannot be guaranteed by the system.
Field 03F 03G
Related parameters iHSPAmode of IPNO - Not supported in case parameter iHSPAmode is set to enabled.
Field 03F 03G
Related parameters iHSPAmode of IPNO - Not supported in case parameter iHSPAmode is set to enabled.
Field 03F 03G
Related parameters iHSPAmode of IPNO - Not supported in case parameter iHSPAmode is set to enabled.
DN70577885 51
Flexi Transport Module Parameters Summary of changes
Id:0900d80580975ffbConfidential
l2PriorityQueueWeight3 (Layer 2 switch member weight for priority queue 3)
l2PriorityQueueWeight4 (Layer 2 switch member weight for priority queue 4)
l2PriorityQueueWeight5 (Layer 2 switch member weight for priority queue 5)
ll2PriorityQueueWeight6 (Layer 2 switch member weight for priority queue 6)
switchId (Layer 2 Switch Object Identifier)
priorityQueuePcp0 (Priority queue for ethernet frames with VLAN PCP bits 0)
Field 03F 03G
Related parameters iHSPAmode of IPNO - Not supported in case parameter iHSPAmode is set to enabled.
Field 03F 03G
Related parameters iHSPAmode of IPNO - Not supported in case parameter iHSPAmode is set to enabled.
Field 03F 03G
Related parameters iHSPAmode of IPNO - Not supported in case parameter iHSPAmode is set to enabled.
Field 03F 03G
Related parameters iHSPAmode of IPNO - Not supported in case parameter iHSPAmode is set to enabled.
Field 03F 03G
Related parameters iHSPAmode of IPNO - Not supported in case parameter iHSPAmode is set to enabled.
Field 03F 03G
Related parameters iHSPAmode of IPNO - Not supported in case parameter iHSPAmode is set to enabled.
52 DN70577885
Flexi Transport Module Parameters
Id:0900d80580975ffbConfidential
Summary of changes
priorityQueuePcp1 (Priority queue for ethernet frames with VLAN PCP bits 1)
priorityQueuePcp2 (Priority queue for ethernet frames with VLAN PCP bits 2)
priorityQueuePcp3 (Priority queue for ethernet frames with VLAN PCP bits 3)
priorityQueuePcp4 (Priority queue for ethernet frames with VLAN PCP bits 4)
priorityQueuePcp5 (Priority queue for ethernet frames with VLAN PCP bits 5)
priorityQueuePcp6 (Priority queue for ethernet frames with VLAN PCP bits 6)
Field 03F 03G
Related parameters iHSPAmode of IPNO - Not supported in case parameter iHSPAmode is set to enabled.
Field 03F 03G
Related parameters iHSPAmode of IPNO - Not supported in case parameter iHSPAmode is set to enabled.
Field 03F 03G
Related parameters iHSPAmode of IPNO - Not supported in case parameter iHSPAmode is set to enabled.
Field 03F 03G
Related parameters iHSPAmode of IPNO - Not supported in case parameter iHSPAmode is set to enabled.
Field 03F 03G
Related parameters iHSPAmode of IPNO - Not supported in case parameter iHSPAmode is set to enabled.
Field 03F 03G
Related parameters iHSPAmode of IPNO - Not supported in case parameter iHSPAmode is set to enabled.
DN70577885 53
Flexi Transport Module Parameters Summary of changes
Id:0900d80580975ffbConfidential
priorityQueuePcp7 (Priority queue for ethernet frames with VLAN PCP bits 7)
priorityQueueNonIP (Priority queue for non-IP frames)
priorityQueueUntagged (Priority queue for untagged ethernet frames)
dscpMap/priorityQueue (Priority queue identifier)
qosClassification (QoS Classification Mode)
vlanAwareSwitch (VLAN Aware Switching Enable)
Field 03F 03G
Related parameters iHSPAmode of IPNO - Not supported in case parameter iHSPAmode is set to enabled.
Field 03F 03G
Related parameters iHSPAmode of IPNO - Not supported in case parameter iHSPAmode is set to enabled.
Field 03F 03G
Related parameters iHSPAmode of IPNO - Not supported in case parameter iHSPAmode is set to enabled.
Field 03F 03G
Related parameters iHSPAmode of IPNO - Not supported in case parameter iHSPAmode is set to enabled.
Field 03F 03G
Related parameters iHSPAmode of IPNO - Not supported in case parameter iHSPAmode is set to enabled.
Field 03F 03G
Related parameters iHSPAmode of IPNO - Not supported in case parameter iHSPAmode is set to enabled.
54 DN70577885
Flexi Transport Module Parameters
Id:0900d80580975ffbConfidential
Summary of changes
OAMMAassocId (Maintenance association identifier)
maName (Name of the maintenance domain)
vlanId (VLAN identifier of the maintenance association)
OAMMDmdLevel (Level of the maintenance domain)
domainId (Maintenance domain identifier)
mdName (Name of the maintenance domain)
Field 03F 03G
Related parameters iHSPAmode of IPNO - Not supported in case parameter iHSPAmode is set to enabled.
Field 03F 03G
Related parameters iHSPAmode of IPNO - Not supported in case parameter iHSPAmode is set to enabled.
Field 03F 03G
Related parameters iHSPAmode of IPNO - Not supported in case parameter iHSPAmode is set to enabled.
Field 03F 03G
Related parameters iHSPAmode of IPNO - Not supported in case parameter iHSPAmode is set to enabled.
Field 03F 03G
Related parameters iHSPAmode of IPNO - Not supported in case parameter iHSPAmode is set to enabled.
Field 03F 03G
Related parameters iHSPAmode of IPNO - Not supported in case parameter iHSPAmode is set to enabled.
DN70577885 55
Flexi Transport Module Parameters Summary of changes
Id:0900d80580975ffbConfidential
OAMMEPaisEnabled (AIS message transmission enabling flag)
aisTxPeriod (AIS messages transmission period)
enableCcm (Allow sending of CCM messages and reset CCM counters)
ccmTxPeriod (Continuity Check Messages transmission period)
ethernetPort (Ethernet link reference)
remoteMepList/macAddr (MAC address of the remote MEP)
Field 03F 03G
Related parameters iHSPAmode of IPNO - Not supported in case parameter iHSPAmode is set to enabled.
Field 03F 03G
Related parameters iHSPAmode of IPNO - Not supported in case parameter iHSPAmode is set to enabled.
Field 03F 03G
Related parameters iHSPAmode of IPNO - Not supported in case parameter iHSPAmode is set to enabled.
Field 03F 03G
Related parameters iHSPAmode of IPNO - Not supported in case parameter iHSPAmode is set to enabled.
Field 03F 03G
Related parameters iHSPAmode of IPNO - Not supported in case parameter iHSPAmode is set to enabled.
Field 03F 03G
Related parameters iHSPAmode of IPNO - Not supported in case parameter iHSPAmode is set to enabled.
56 DN70577885
Flexi Transport Module Parameters
Id:0900d80580975ffbConfidential
Summary of changes
oammepId (Maintenance association endpoint identifier)
remoteMepList/mepId (Remote maintenance association endpoint identifier)
remoteMepList (Remote maintenance association endpoints list)
vlanPrio (VLAN PCP bits)
OAMPRFenableCcm (Allow sending of CCM messages and reset CCM counters)
efEventWindow (Errored Frame Event counting interval)
Field 03F 03G
Related parameters iHSPAmode of IPNO - Not supported in case parameter iHSPAmode is set to enabled.
Field 03F 03G
Related parameters iHSPAmode of IPNO - Not supported in case parameter iHSPAmode is set to enabled.
Field 03F 03G
Related parameters iHSPAmode of IPNO - Not supported in case parameter iHSPAmode is set to enabled.
Field 03F 03G
Related parameters iHSPAmode of IPNO - Not supported in case parameter iHSPAmode is set to enabled.
Field 03F 03G
Related parameters iHSPAmode of IPNO - Not supported in case parameter iHSPAmode is set to enabled.
Field 03F 03G
Related parameters iHSPAmode of IPNO - Not supported in case parameter iHSPAmode is set to enabled.
DN70577885 57
Flexi Transport Module Parameters Summary of changes
Id:0900d80580975ffbConfidential
efEventThreshold (Errored Frame Event counting threshold)
efpEventThreshold (Errored Frame Period Event counting threshold)
alarmClearanceDelay (Link OAM Link Critical Event Alarm clearance delay)
testFrameSize (Link OAM loopback test message frame size)
testFrameRate (Link OAM loopback test message rate)
Field 03F 03G
Related parameters iHSPAmode of IPNO - Not supported in case parameter iHSPAmode is set to enabled.
Field 03F 03G
Related parameters iHSPAmode of IPNO - Not supported in case parameter iHSPAmode is set to enabled.
Field 03F 03G
Related parameters iHSPAmode of IPNO - Not supported in case parameter iHSPAmode is set to enabled.
efpEventWindow of OAMPRF - Config-ured value for efpEventThreshold should be within configured value for OAMPRF-efpEventWindow to enable the possibility of generating Errored Frame Period Event Notifications
efpEventWindow of OAMPRF - Config-ured value for efpEventThreshold should be within configured value for OAMPRF-efpEventWindow to enable the possibility of generating Errored Frame Period Event Notifications
Field 03F 03G
Related parameters iHSPAmode of IPNO - Not supported in case parameter iHSPAmode is set to enabled.
Field 03F 03G
Related parameters iHSPAmode of IPNO - Not supported in case parameter iHSPAmode is set to enabled.
Field 03F 03G
Related parameters iHSPAmode of IPNO - Not supported in case parameter iHSPAmode is set to enabled.
58 DN70577885
Flexi Transport Module Parameters
Id:0900d80580975ffbConfidential
Summary of changes
activeMode (Link OAM operational mode at local peer)
OSPFV2ospfAreas/areaId (OSPF area identifier)
ospfAreas (OSPF area list)
ospfAreas/areaStub (OSPF area stub flag)
ospfEnabled (OSPF enabling flag)
spfMaxHoldTime (OSPF maximum Shortest Path First hold time)
Field 03F 03G
Related parameters iHSPAmode of IPNO - Not supported in case parameter iHSPAmode is set to enabled.
Field 03F 03G
Related parameters iHSPAmode of IPNO - Not supported in case parameter iHSPAmode is set to enabled.
Field 03F 03G
Related parameters iHSPAmode of IPNO - Not supported in case parameter iHSPAmode is set to enabled.
Field 03F 03G
Related parameters iHSPAmode of IPNO - Not supported in case parameter iHSPAmode is set to enabled.
Field 03F 03G
Related parameters iHSPAmode of IPNO - Not supported in case parameter iHSPAmode is set to enabled.
unitTypeExpected of UNIT - OSPF is not supported on the following modules: FTEB, FTHA, FTPB, FTFA.
unitTypeExpected of UNIT - OSPF is not supported on the following modules: FTEB, FTHA, FTPB, FTFA.
Field 03F 03G
Related parameters iHSPAmode of IPNO - Not supported in case parameter iHSPAmode is set to enabled.
DN70577885 59
Flexi Transport Module Parameters Summary of changes
Id:0900d80580975ffbConfidential
ospfRouterId (OSPF router identification)
confPref (OSPF routing preference value)
spfHoldTime (OSPF Shortest Path First hold time)
spfDelay (OSPF Shortest Path First recalculation delay)
refBandwidth (Reference bandwidth for OSPF cost equal to 1)
P3LPacFieldCompressionOn (Access Control Field Compression flag)
Field 03F 03G
Related parameters iHSPAmode of IPNO - Not supported in case parameter iHSPAmode is set to enabled.
ospfEnabled of OSPFV2 - "ospfRouterId" should be overwritten if ospfEnabled is true and areaId is 0.0.0.0.
ospfEnabled of OSPFV2 - "ospfRouterId" should be overwritten if ospfEnabled is true and areaId is 0.0.0.0.
Field 03F 03G
Related parameters iHSPAmode of IPNO - Not supported in case parameter iHSPAmode is set to enabled.
Field 03F 03G
Related parameters iHSPAmode of IPNO - Not supported in case parameter iHSPAmode is set to enabled.
Field 03F 03G
Related parameters iHSPAmode of IPNO - Not supported in case parameter iHSPAmode is set to enabled.
Field 03F 03G
Related parameters iHSPAmode of IPNO - Not supported in case parameter iHSPAmode is set to enabled.
Field 03F 03G
Related parameters iHSPAmode of IPNO - Not supported in case parameter iHSPAmode is set to enabled.
60 DN70577885
Flexi Transport Module Parameters
Id:0900d80580975ffbConfidential
Summary of changes
fcsFieldLength (Frame Check Sequence field size)
magicNumberOn (Magic number flag)
mruSize (Maximum Receive Unit (MRU) size)
p3lpId (PPP link identifier)
protocolFieldCompressionOn (Protocol Field Compression flag)
P3MLadministrativeState (Administrative state of the PPP multi-link)
endPointDiscriminatorType (Endpoint discriminator type)
Field 03F 03G
Related parameters iHSPAmode of IPNO - Not supported in case parameter iHSPAmode is set to enabled.
Field 03F 03G
Related parameters iHSPAmode of IPNO - Not supported in case parameter iHSPAmode is set to enabled.
Field 03F 03G
Related parameters iHSPAmode of IPNO - Not supported in case parameter iHSPAmode is set to enabled.
Field 03F 03G
Related parameters iHSPAmode of IPNO - Not supported in case parameter iHSPAmode is set to enabled.
Field 03F 03G
Related parameters iHSPAmode of IPNO - Not supported in case parameter iHSPAmode is set to enabled.
Field 03F 03G
Related parameters iHSPAmode of IPNO - Not supported in case parameter iHSPAmode is set to enabled.
DN70577885 61
Flexi Transport Module Parameters Summary of changes
Id:0900d80580975ffbConfidential
mpFragmentSize (Fragment size in egress direction)
ts16Excluded (Is timeslot TS16 excluded)
mrruSize (Maximum Receive Reconstructed Unit (MRRU) size)
netmask (Netmask of the IP address of the PPP endpoint)
interfaces (Physical interface list)
p3pIpAddr (PPP endpoint IP address)
Field 03F 03G
Related parameters iHSPAmode of IPNO - Not supported in case parameter iHSPAmode is set to enabled.
Field 03F 03G
Related parameters iHSPAmode of IPNO - Not supported in case parameter iHSPAmode is set to enabled.
Field 03F 03G
Related parameters iHSPAmode of IPNO - Not supported in case parameter iHSPAmode is set to enabled.
Field 03F 03G
Related parameters iHSPAmode of IPNO - Not supported in case parameter iHSPAmode is set to enabled.
Field 03F 03G
Related parameters iHSPAmode of IPNO - Not supported in case parameter iHSPAmode is set to enabled.
Field 03F 03G
Related parameters iHSPAmode of IPNO - Not supported in case parameter iHSPAmode is set to enabled.
62 DN70577885
Flexi Transport Module Parameters
Id:0900d80580975ffbConfidential
Summary of changes
p3mlId (PPP multi-link identifier)
shortSeqNrOn (Short sequence numbering flag)
P3SLadministrativeState (Administrative state of the PPP link)
ts16Excluded (Is timeslot TS16 excluded)
netmask (Netmask for the IP address of the PPP endpoint)
interface (Physical interface list)
Field 03F 03G
Related parameters iHSPAmode of IPNO - Not supported in case parameter iHSPAmode is set to enabled.
Field 03F 03G
Related parameters iHSPAmode of IPNO - Not supported in case parameter iHSPAmode is set to enabled.
Field 03F 03G
Related parameters iHSPAmode of IPNO - Not supported in case parameter iHSPAmode is set to enabled.
Field 03F 03G
Related parameters iHSPAmode of IPNO - Not supported in case parameter iHSPAmode is set to enabled.
Field 03F 03G
Related parameters iHSPAmode of IPNO - Not supported in case parameter iHSPAmode is set to enabled.
Field 03F 03G
Related parameters iHSPAmode of IPNO - Not supported in case parameter iHSPAmode is set to enabled.
DN70577885 63
Flexi Transport Module Parameters Summary of changes
Id:0900d80580975ffbConfidential
p3pIpAddr (PPP endpoint IP address)
p3slId (PPP single link object instance identifier)
QOStrafficTypesMap (Quality of Service mapping table)
trafficTypesMap/trafficType (Traffic type)
TMPARdcnCommittedBitRate (DCN Committed Bit Rate)
externalNATIpAddress (External NAT IP Address)
Field 03F 03G
Related parameters iHSPAmode of IPNO - Not supported in case parameter iHSPAmode is set to enabled.
Field 03F 03G
Related parameters iHSPAmode of IPNO - Not supported in case parameter iHSPAmode is set to enabled.
Field 03F 03G
Related parameters iHSPAmode of IPNO - Not supported in case parameter iHSPAmode is set to enabled.
Field 03F 03G
Related parameters iHSPAmode of IPNO - In iHSPAmode, QOS configuration supports the IubIp traffictypes.
Field 03F 03G
Related parameters iHSPAmode of IPNO - Value "OSPF" is not supported if iHSPAmode is set to enabled.
iHSPAmode of IPNO - Value "OSPF, CES and BFD" is not supported if iHSPA-mode is set to enabled.
Field 03F 03G
Default value 150
64 DN70577885
Flexi Transport Module Parameters
Id:0900d80580975ffbConfidential
Summary of changes
signallingCommittedBitRate (Signalling Committed Bit Rate)
TWAMPdscp (DSCP value for TWAMP message transmission)
administrativeState (Lock or unlock a TWAMP session)
plrAlarmThreshold (Packet loss ratio alarm threshold)
rttAlarmThreshold (Round-trip-time alarm threshold)
messageSize (TWAMP initiator message size)
Field 03F 03G
Related parameters iHSPAmode of IPNO - In iHSPAmode, QOS configuration supports the IubIp traffictypes.
Field 03F 03G
Default value 100
Field 03F 03G
Related parameters iHSPAmode of IPNO - In iHSPAmode, QOS configuration supports the IubIp traffictypes.
Field 03F 03G
Related parameters iHSPAmode of IPNO - In iHSPAmode, QOS configuration supports the IubIp traffictypes.
Field 03F 03G
Related parameters iHSPAmode of IPNO - In iHSPAmode, QOS configuration supports the IubIp traffictypes.
Field 03F 03G
Related parameters iHSPAmode of IPNO - In iHSPAmode, QOS configuration supports the IubIp traffictypes.
DN70577885 65
Flexi Transport Module Parameters Summary of changes
Id:0900d80580975ffbConfidential
sourceIpAddress (TWAMP initiator messages source IP address)
destIpAddress (TWAMP session destination IP address)
destPort (TWAMP session destination port)
twampId (TWAMP session identifier)
Field 03F 03G
Related parameters iHSPAmode of IPNO - In iHSPAmode, QOS configuration supports the IubIp traffictypes.
mtu of IPNO - The value of the parameter messageSize shall not exceed the Maximum Transfer Unit value of the FTM.
mtu of IPNO - The value of the parameter messageSize shall not exceed the Maximum Transfer Unit value of the FTM.
Field 03F 03G
Related parameters iHSPAmode of IPNO - In iHSPAmode, QOS configuration supports the IubIp traffictypes.
administrativeState of TWAMP - The TWAMP session must be locked, before its source IP address can be changed (set administrativeState to "locked").
administrativeState of TWAMP - The TWAMP session must be locked, before its source IP address can be changed (set administrativeState to "locked").
Field 03F 03G
Related parameters iHSPAmode of IPNO - In iHSPAmode, QOS configuration supports the IubIp traffictypes.
administrativeState of TWAMP - The TWAMP session must be locked, before its destination IP address can be changed (set administrativeState to "locked").
administrativeState of TWAMP - The TWAMP session must be locked, before its destination IP address can be changed (set administrativeState to "locked").
Field 03F 03G
Related parameters iHSPAmode of IPNO - In iHSPAmode, QOS configuration supports the IubIp traffictypes.
administrativeState of TWAMP - Changeing the destination port of the session requires locking it.
administrativeState of TWAMP - Changeing the destination port of the session requires locking it.
66 DN70577885
Flexi Transport Module Parameters
Id:0900d80580975ffbConfidential
Summary of changes
Removed parametersIEIF
• mtuIgnore (MTU mismatch detection in use)
IVIF
• mtuIgnore (MTU mismatch detection in use)
Field 03F 03G
Related parameters iHSPAmode of IPNO - In iHSPAmode, QOS configuration supports the IubIp traffictypes.
DN70577885 67
Flexi Transport Module Parameters Introduction
Id:0900d80580975ffbConfidential
1 IntroductionThis document describes the Flexi Transport Module Parameters used in WBTS WN7.0 1.0 and WN7.0 2.0 release.
For detailed information on changes between Flexi Transport Module Parameters WBTS7.0 1.0 and WBTS6.0 parameters, see the WCDMA RAN, Rel. RU30, Changes document.
g All FTM parameter changes done from NetAct result in a SCF download and acti-vation, and hence a BTS restart.
g If there is a difference in range/default value between WN7.0 2.0 and WN7.0 1.0 param-eters, or when a parameter is specific only to one of these releases, it is indicated in the description of the parameter.
Please note the following definitions for the Range, Step and Unit values used in the parameter tables:
• Range: The user interface value range for the parameter. If unit is character then range specifies number of characters in string (minimum number - maximum number).
• Step: The value by which the parameter value increases or decreases within the range.
• Unit: The measurement unit in use for the range and step, for example, s (second), min (minute), h (hour), m (meter), km (kilometer), dB (decibel), dBm, bit/s (bit per second), kbit/s (kilobit per second), character, % (per cent), per mil, period. If no unit is given, it means that the value range has no measurement unit or the parameter value cannot be changed in steps.
68 DN70577885
Flexi Transport Module Parameters
Id:0900d80580975ffbConfidential
A2NE Parameters
2 A2NE Parameters
2.1 aal2NodeId (AAL2 Node Identifier)
Parameter name AAL2 Node Identifier
Abbreviated name aal2NodeId
3GPP name -
Managed Object A2NE
Multiplicity 1
Description This parameter identifies the BTS AAL2 node. Because BTS transport represents a single AAL2 node, the identifier is always 1.
Range 1... 1
Units -
Formula for getting internal value
internal_value = gui_value
Default value -
Default value notes -
Related functions -
Modification Not modifiable
Related parameters -
Parameter relationships -
Related options -
Feature dependencies -
Interfaces • EM <-> FTM • RAC -> FTM • RAC <-> RACApp
References -
Validation pattern -
Table 1 aal2NodeId (AAL2 Node Identifier)
DN70577885 69
Flexi Transport Module Parameters A2ST Parameters
Id:0900d80580975ffbConfidential
3 A2ST Parameters
3.1 AAL2EndAddress (AAL2 End Address)
3.2 VCI (Virtual Channel Identifier)
Parameter name AAL2 End Address
Abbreviated name AAL2EndAddress
3GPP name -
Managed Object A2ST
Multiplicity 1
Description AAL2 endpoint address (A2EA) for a signalling link.
The value has to be the same as the one configured in the RNC.
Range 40
Units characters
Formula for getting internal value
internal_value = gui_value
Default value -
Default value notes -
Related functions -
Modification On-Line
Related parameters -
Parameter relationships -
Related options -
Feature dependencies -
Interfaces • EM <-> FTM • RAC <-> FTM • RAC <-> RACApp
References -
Validation pattern -
Table 2 AAL2EndAddress (AAL2 End Address)
Parameter name Virtual Channel Identifier
Abbreviated name VCI
3GPP name -
Table 3 VCI (Virtual Channel Identifier)
70 DN70577885
Flexi Transport Module Parameters
Id:0900d80580975ffbConfidential
A2ST Parameters
3.3 VPI (Virtual Path Identifier)
Managed Object A2ST
Multiplicity 1
Description Virtual Channel Identifier.
Range 32... 4095
Units -
Formula for getting internal value
internal_value = gui_value
Default value -
Default value notes -
Related functions -
Modification Not modifiable
Related parameters -
Parameter relationships -
Related options -
Feature dependencies -
Interfaces • FTM -> EM • FTM -> RAC
References -
Validation pattern -
Table 3 VCI (Virtual Channel Identifier) (Cont.)
Parameter name Virtual Path Identifier
Abbreviated name VPI
3GPP name -
Managed Object A2ST
Multiplicity 1
Description Virtual Path Identifier.
Range 0... 255
Units -
Formula for getting internal value
internal_value = gui_value
Default value -
Default value notes -
Related functions -
Table 4 VPI (Virtual Path Identifier)
DN70577885 71
Flexi Transport Module Parameters A2ST Parameters
Id:0900d80580975ffbConfidential
3.4 aal2sigTTPId (AAL2 Signalling Link Identifier)
Modification Not modifiable
Related parameters -
Parameter relationships -
Related options -
Feature dependencies -
Interfaces • FTM -> EM • FTM -> RAC
References -
Validation pattern -
Table 4 VPI (Virtual Path Identifier) (Cont.)
Parameter name AAL2 Signalling Link Identifier
Abbreviated name aal2sigTTPId
3GPP name -
Managed Object A2ST
Multiplicity 1
Description This parameter identifies the AAL2 signalling link.
The identifier is composed from the elements:
- Unit number (unit#)
- Interface number(if#, imag# or pw#)
- Virtual Path Identifier (vpi#)
- Virtual Channel Identifier (vci#)
Format:
- unit#-if#-vpi#vci# (e.g. 1-8-000C0)
- unit#-imag#-vpi#vci# (e.g. 1-34-00210)
Range:
unit#: 1
if#: 1..16 (maxi. 2 digits)
imag#: 33..75 (2 digits)
pw#: 76
vpi#: 00..FF (hexadecimal number, 2 digits)
vci#: 000..FFF (hexadecimal number, 3 digits)
Range 9...10
Units characters
Table 5 aal2sigTTPId (AAL2 Signalling Link Identifier)
72 DN70577885
Flexi Transport Module Parameters
Id:0900d80580975ffbConfidential
A2ST Parameters
3.5 interfaceNumber (Interface Number)
Formula for getting internal value
internal_value = gui_value
Default value -
Default value notes -
Related functions -
Modification Not modifiable
Related parameters VCI of A2ST
VPI of A2ST
interfaceNumber of A2ST
unitNumber of A2ST
Parameter relationships The A2ST id is composed of the values of these other attributes
Related options -
Feature dependencies -
Interfaces • EM <-> FTM • RAC -> FTM • RAC <-> RACApp
References -
Validation pattern -
Table 5 aal2sigTTPId (AAL2 Signalling Link Identifier) (Cont.)
Parameter name Interface Number
Abbreviated name interfaceNumber
3GPP name -
Managed Object A2ST
Multiplicity 1
Description Defines the location of the physical interface on the unit.
The value range depends on the unit type.
FTEB, FTPB, FTIF, FIIF: 1..8
FIIB, FILB, FTIA, FTIB, FTJA, FTLB: 1..4
FTFB, FTFA, FTHA: 1..16
In case of Inverse Multiplexing for ATM (IMA) the value range is: 33..75.
For ATM over Ethernet, the value is always: 76.
Table 6 interfaceNumber (Interface Number)
DN70577885 73
Flexi Transport Module Parameters A2ST Parameters
Id:0900d80580975ffbConfidential
3.6 stcAlarmEnable (Signalling Transport Converter Alarm Enable)
Range 1... 76
Units -
Formula for getting internal value
internal_value = gui_value
Default value -
Default value notes -
Related functions -
Modification Not modifiable
Related parameters -
Parameter relationships -
Related options -
Feature dependencies -
Interfaces • FTM -> EM • FTM -> RAC
References -
Validation pattern -
Table 6 interfaceNumber (Interface Number) (Cont.)
Parameter name Signalling Transport Converter Alarm Enable
Abbreviated name stcAlarmEnable
3GPP name -
Managed Object A2ST
Multiplicity 1
Description Enables or disables alarm 61260 "STC connection to signalling peer not established". If enabled, the FTM observes the availability of the adjacent node's signalling link.
Range false (0), true (1)
Units -
Formula for getting internal value
• false => 0 • true => 1
Default value false (0)
Default value notes -
Table 7 stcAlarmEnable (Signalling Transport Converter Alarm Enable)
74 DN70577885
Flexi Transport Module Parameters
Id:0900d80580975ffbConfidential
A2ST Parameters
3.7 unitNumber (Unit Number)
Related functions -
Modification On-Line
Related parameters -
Parameter relationships -
Related options -
Feature dependencies -
Interfaces • EM <-> FTM • RAC <-> FTM • RAC <-> RACApp
References -
Validation pattern -
Table 7 stcAlarmEnable (Signalling Transport Converter Alarm Enable) (Cont.)
Parameter name Unit Number
Abbreviated name unitNumber
3GPP name -
Managed Object A2ST
Multiplicity 1
Description Specifies the location of the unit (slot number). In this release it is always 1. The BTS has only 1 unit in slot 1.
Range 1... 1
Units -
Formula for getting internal value
internal_value = gui_value
Default value -
Default value notes -
Related functions -
Modification Not modifiable
Related parameters -
Parameter relationships -
Related options -
Feature dependencies -
Table 8 unitNumber (Unit Number)
DN70577885 75
Flexi Transport Module Parameters A2ST Parameters
Id:0900d80580975ffbConfidential
Interfaces • FTM -> EM • FTM -> RAC
References -
Validation pattern -
Table 8 unitNumber (Unit Number) (Cont.)
76 DN70577885
Flexi Transport Module Parameters
Id:0900d80580975ffbConfidential
A2UT Parameters
4 A2UT Parameters
4.1 VCI (Virtual Channel Identifier)
4.2 VPI (Virtual Path Identifier)
Parameter name Virtual Channel Identifier
Abbreviated name VCI
3GPP name -
Managed Object A2UT
Multiplicity 1
Description Virtual Channel Identifier.
Range 32... 4095
Units -
Formula for getting internal value
internal_value = gui_value
Default value -
Default value notes -
Related functions -
Modification Not modifiable
Related parameters -
Parameter relationships -
Related options -
Feature dependencies -
Interfaces • FTM -> EM • FTM -> RAC
References -
Validation pattern -
Table 9 VCI (Virtual Channel Identifier)
Parameter name Virtual Path Identifier
Abbreviated name VPI
3GPP name -
Managed Object A2UT
Multiplicity 1
Description Virtual Path Identifier.
Table 10 VPI (Virtual Path Identifier)
DN70577885 77
Flexi Transport Module Parameters A2UT Parameters
Id:0900d80580975ffbConfidential
4.3 aal2pathTTPId (AAL2 User Path Identifier)
Range 0... 255
Units -
Formula for getting internal value
internal_value = gui_value
Default value -
Default value notes -
Related functions -
Modification Not modifiable
Related parameters -
Parameter relationships -
Related options -
Feature dependencies -
Interfaces • FTM -> EM • FTM -> RAC
References -
Validation pattern -
Table 10 VPI (Virtual Path Identifier) (Cont.)
Parameter name AAL2 User Path Identifier
Abbreviated name aal2pathTTPId
3GPP name -
Managed Object A2UT
Multiplicity 1
Table 11 aal2pathTTPId (AAL2 User Path Identifier)
78 DN70577885
Flexi Transport Module Parameters
Id:0900d80580975ffbConfidential
A2UT Parameters
Description Identifies the AAL2 User Path.
The object is identified by
- Unitnumber (unit#)
- Interfacenumber(if#, imag# or pw#)
- Virtual Path Identifier (vpi#)
- Virtual Channel Identifier (vci#)
Format:
- unit#-if#-vpi#vci# (e.g. 2-8-000C0)
- unit#-imag#-vpi#vci# (e.g. 2-34-00210)
Range:
unit#: 1
if#: 1..16 (maxi. 2 digits)
imag#: 33..75 (2 digits)
pw#: 76
vpi#: 00..FF (hexadecimal number, 2 digits)
vci#: 000..FFF (hexadecimal number, 3 digits)
Range 9...10
Units characters
Formula for getting internal value
internal_value = gui_value
Default value -
Default value notes -
Related functions -
Modification Not modifiable
Related parameters VCI of A2UT
VPI of A2UT
interfaceNumber of A2UT
unitNumber of A2UT
Parameter relationships The A2UT id is composed of the values of these other attributes
Related options -
Feature dependencies -
Interfaces • EM <-> FTM • RAC -> FTM • RAC <-> RACApp
References -
Validation pattern -
Table 11 aal2pathTTPId (AAL2 User Path Identifier) (Cont.)
DN70577885 79
Flexi Transport Module Parameters A2UT Parameters
Id:0900d80580975ffbConfidential
4.4 interfaceNumber (Interface Number)
4.5 pid (Path Identifier)
Parameter name Interface Number
Abbreviated name interfaceNumber
3GPP name -
Managed Object A2UT
Multiplicity 1
Description Defines the location of the physical interface on the unit.
The value range depends on the unit type.
FTEB, FTPB, FTIF, FIIF: 1..8
FIIB, FILB, FTIA, FTIB, FTJA, FTLB: 1..4
FTFB, FTFA, FTHA: 1..16
In case of Inverse Multiplexing for ATM (IMA) the value range is: 33..75.
For ATM over Ethernet, the value is always: 76.
Range 1... 76
Units -
Formula for getting internal value
internal_value = gui_value
Default value -
Default value notes -
Related functions -
Modification Not modifiable
Related parameters -
Parameter relationships -
Related options -
Feature dependencies -
Interfaces • FTM -> EM • FTM -> RAC
References -
Validation pattern -
Table 12 interfaceNumber (Interface Number)
Parameter name Path Identifier
Table 13 pid (Path Identifier)
80 DN70577885
Flexi Transport Module Parameters
Id:0900d80580975ffbConfidential
A2UT Parameters
4.6 queue2Weight (Weight of AAL2 user path queue Q2)
Abbreviated name pid
3GPP name -
Managed Object A2UT
Multiplicity 1
Description Associates AAL2 signalling messages to the VCC (AAL2 user path) that has been selected as the carrier for the AAL2 connection.
The PID is unique for each AAL2 signalling link (A2ST, ANI).
Range 0... 99999999
Units -
Formula for getting internal value
internal_value = gui_value
Default value -
Default value notes -
Related functions -
Modification On-Line
Related parameters -
Parameter relationships -
Related options -
Feature dependencies -
Interfaces • EM <-> FTM • RAC <-> FTM • RAC <-> RACApp
References -
Validation pattern -
Table 13 pid (Path Identifier) (Cont.)
Parameter name Weight of AAL2 user path queue Q2
Abbreviated name queue2Weight
3GPP name -
Managed Object A2UT
Multiplicity 1
Description This is the weight of AAL2 User Path queue Q2.
Range 1... 1000
Table 14 queue2Weight (Weight of AAL2 user path queue Q2)
DN70577885 81
Flexi Transport Module Parameters A2UT Parameters
Id:0900d80580975ffbConfidential
4.7 queue3Weight (Weight of AAL2 user path queue Q3)
Units -
Formula for getting internal value
internal_value = gui_value
Default value 1000
Default value notes -
Related functions -
Modification On-Line
Related parameters -
Parameter relationships -
Related options • RAN1253 Iub Transport QoS
Feature dependencies -
Interfaces • EM <-> FTM • RAC <-> FTM • RAC <-> RACApp
References -
Validation pattern -
Table 14 queue2Weight (Weight of AAL2 user path queue Q2) (Cont.)
Parameter name Weight of AAL2 user path queue Q3
Abbreviated name queue3Weight
3GPP name -
Managed Object A2UT
Multiplicity 1
Description This is the weight of AAL2 User Path queue Q3.
Range 1... 1000
Units -
Formula for getting internal value
internal_value = gui_value
Default value 500
Default value notes -
Related functions -
Modification On-Line
Related parameters -
Parameter relationships -
Table 15 queue3Weight (Weight of AAL2 user path queue Q3)
82 DN70577885
Flexi Transport Module Parameters
Id:0900d80580975ffbConfidential
A2UT Parameters
4.8 queue4Weight (Weight of AAL2 user path queue Q4)
Related options • RAN1253 Iub Transport QoS
Feature dependencies -
Interfaces • EM <-> FTM • RAC <-> FTM • RAC <-> RACApp
References -
Validation pattern -
Table 15 queue3Weight (Weight of AAL2 user path queue Q3) (Cont.)
Parameter name Weight of AAL2 user path queue Q4
Abbreviated name queue4Weight
3GPP name -
Managed Object A2UT
Multiplicity 1
Description This is the weight of AAL2 User Path queue Q4.
Range 1... 1000
Units -
Formula for getting internal value
internal_value = gui_value
Default value 1
Default value notes -
Related functions -
Modification On-Line
Related parameters -
Parameter relationships -
Related options • RAN1253 Iub Transport QoS
Feature dependencies -
Interfaces • EM <-> FTM • RAC <-> FTM • RAC <-> RACApp
References -
Validation pattern -
Table 16 queue4Weight (Weight of AAL2 user path queue Q4)
DN70577885 83
Flexi Transport Module Parameters A2UT Parameters
Id:0900d80580975ffbConfidential
4.9 unitNumber (Unit Number)
Parameter name Unit Number
Abbreviated name unitNumber
3GPP name -
Managed Object A2UT
Multiplicity 1
Description Specifies the location of the unit (slot number). In this release it is always 1. The BTS has only 1 unit in slot 1.
Range 1... 1
Units -
Formula for getting internal value
internal_value = gui_value
Default value -
Default value notes -
Related functions -
Modification Not modifiable
Related parameters -
Parameter relationships -
Related options -
Feature dependencies -
Interfaces • FTM -> EM • FTM -> RAC
References -
Validation pattern -
Table 17 unitNumber (Unit Number)
84 DN70577885
Flexi Transport Module Parameters
Id:0900d80580975ffbConfidential
ACCP Parameters
5 ACCP Parameters
5.1 atmAccessProfileId (ATM Access Profile Identifier)
5.2 egressBandwidth (Egress Bandwidth)
Parameter name ATM Access Profile Identifier
Abbreviated name atmAccessProfileId
3GPP name -
Managed Object ACCP
Multiplicity 1
Description Identifies the ATM Access Profile. The value is always 1. Exactly 1 ATM access profile exists on the BTS for the ATM over Ethernet interface.
Range 1... 1
Units -
Formula for getting internal value
internal_value = gui_value
Default value -
Default value notes -
Related functions -
Modification Not modifiable
Related parameters -
Parameter relationships -
Related options -
Feature dependencies -
Interfaces • EM <-> FTM • RAC -> FTM • RAC <-> RACApp
References -
Validation pattern -
Table 18 atmAccessProfileId (ATM Access Profile Identifier)
Parameter name Egress Bandwidth
Abbreviated name egressBandwidth
3GPP name -
Table 19 egressBandwidth (Egress Bandwidth)
DN70577885 85
Flexi Transport Module Parameters ACCP Parameters
Id:0900d80580975ffbConfidential
Managed Object ACCP
Multiplicity 1
Description Defines the maximum allowed egress bandwidth in cells per second for a logical ATM interface.
The value range of egressBandwidth is as follows:
- E1: fixed value 4528
- T1/JT1: fixed value 3622
- STM-1: 36..144896, step 1, default 144896 (32 x E1)
- ATM over Ethernet (pseudowire): 1132..144896, step 1132, default 144896.
- IMA E1: fixed value: int[n*4526*(m-1)/m] where m = Tx Frame Length and n = number of IMA links in a group
- IMA T1/JT1 fixed value: int[n*3621*(m-1)/m] where m = Tx Frame Length and n = number of IMA links in a group
Range 36... 144896
Units cells/s
Formula for getting internal value
internal_value = gui_value
Default value 144896
Default value notes The range, step and default value of the parameter depend on the interface type.The default value of 144896 e.g. applies only to Pseudowire and STM-1. See the description of the parameter for more details.
Related functions -
Modification On-Line
Related parameters -
Parameter relationships -
Related options -
Feature dependencies -
Interfaces • EM <-> FTM • RAC <-> FTM • RAC <-> RACApp
References -
Validation pattern -
Table 19 egressBandwidth (Egress Bandwidth) (Cont.)
86 DN70577885
Flexi Transport Module Parameters
Id:0900d80580975ffbConfidential
ACCP Parameters
5.3 ingressBandwidth (Ingress Bandwidth)
Parameter name Ingress Bandwidth
Abbreviated name ingressBandwidth
3GPP name -
Managed Object ACCP
Multiplicity 1
Description Defines the maximum allowed ingress bandwidth in cells per second for a logical ATM interface.
For the following interfaces the values are fixed:
- E1: 4528
- STM-1: 144896 (32 x E1)
- T1/JT1: 3622
- IMA E1: int[n*4526*(m-1)/m] where m = Tx Frame Length and n = number of IMA links in a group
- IMA T1/JT1: int[n*3621*(m-1)/m] where m = Tx Frame Length and n = number of IMA links in a group
For ATM over Ethernet (Pseudowire tunnel) the value is operator configurable from 1132 to 144896 in steps of 1132.
Range 1132... 144896
Units cells/s
Formula for getting internal value
internal_value = gui_value
Default value 144896
Default value notes Range and step and default value refer only to ATM over Ethernet, because this is the only case where the parameter is configurable. For the other cases always the values from the "description" apply.
Related functions -
Modification On-Line
Related parameters -
Parameter relationships -
Related options -
Feature dependencies -
Interfaces • EM <-> FTM • RAC <-> FTM • RAC <-> RACApp
Table 20 ingressBandwidth (Ingress Bandwidth)
DN70577885 87
Flexi Transport Module Parameters ACCP Parameters
Id:0900d80580975ffbConfidential
References -
Validation pattern -
Table 20 ingressBandwidth (Ingress Bandwidth) (Cont.)
88 DN70577885
Flexi Transport Module Parameters
Id:0900d80580975ffbConfidential
AMGR Parameters
6 AMGR Parameters
6.1 amgrId (Account Manager Identifier)
6.2 ldapConnectionType (LDAP Server TLS access mode)
Parameter name Account Manager Identifier
Abbreviated name amgrId
3GPP name -
Managed Object AMGR
Multiplicity 1
Description This parameter identifies the BTS account manager configuration. The value is always 1.
Range 1... 1
Units -
Formula for getting internal value
internal_value = gui_value
Default value -
Default value notes -
Related functions -
Modification Not modifiable
Related parameters -
Parameter relationships -
Related options -
Feature dependencies -
Interfaces • EM <-> FTM • RAC -> FTM • RAC <-> RACApp
References -
Validation pattern -
Table 21 amgrId (Account Manager Identifier)
Parameter name LDAP Server TLS access mode
Abbreviated name ldapConnectionType
3GPP name -
Managed Object AMGR
Table 22 ldapConnectionType (LDAP Server TLS access mode)
DN70577885 89
Flexi Transport Module Parameters AMGR Parameters
Id:0900d80580975ffbConfidential
6.3 primaryLdapPort (Port Number of Primary LDAP Server)
Multiplicity 1
Description This parameter holds the TLS access mode for the LDAP server(s) of the BTS. Values are "TLS" (allow only secured connections) and "TLS_OR_PLAIN_TEXT" (allow both unsecured and secured connections).
Range TLS (0), TLS_OR_PLAIN_TEXT (1)
Units -
Formula for getting internal value
gui ==> internal
TLS ==> 0
TLS_OR_PLAIN_TEXT ==> 1
Default value TLS (0)
Default value notes -
Related functions -
Modification On-Line
Related parameters -
Parameter relationships -
Related options • RAN1314 Secure LDAP
Feature dependencies -
Interfaces • EM <-> FTM • RAC <-> FTM • RAC <-> RACApp
References -
Validation pattern -
Table 22 ldapConnectionType (LDAP Server TLS access mode) (Cont.)
Parameter name Port Number of Primary LDAP Server
Abbreviated name primaryLdapPort
3GPP name -
Managed Object AMGR
Multiplicity 1
Description The port number of the Primary LDAP Server.
Range 1... 65535
Units -
Table 23 primaryLdapPort (Port Number of Primary LDAP Server)
90 DN70577885
Flexi Transport Module Parameters
Id:0900d80580975ffbConfidential
AMGR Parameters
6.4 primaryLdapServer (IP address of Primary LDAP Server)
Formula for getting internal value
internal_value = gui_value
Default value 389
Default value notes standard port for LDAP
Related functions -
Modification On-Line
Related parameters -
Parameter relationships -
Related options -
Feature dependencies -
Interfaces • EM <-> FTM • RAC <-> FTM • RAC <-> RACApp
References -
Validation pattern -
Table 23 primaryLdapPort (Port Number of Primary LDAP Server) (Cont.)
Parameter name IP address of Primary LDAP Server
Abbreviated name primaryLdapServer
3GPP name -
Managed Object AMGR
Multiplicity 1
Description The IP address of the Primary LDAP Server, as dotted decimal string.
Range 7...15
Units characters
Formula for getting internal value
internal_value = gui_value
Default value -
Default value notes -
Related functions -
Modification On-Line
Related parameters -
Parameter relationships -
Table 24 primaryLdapServer (IP address of Primary LDAP Server)
DN70577885 91
Flexi Transport Module Parameters AMGR Parameters
Id:0900d80580975ffbConfidential
Related options -
Feature dependencies -
Interfaces • EM <-> FTM • RAC <-> FTM • RAC <-> RACApp
References -
Validation pattern -
Table 24 primaryLdapServer (IP address of Primary LDAP Server) (Cont.)
92 DN70577885
Flexi Transport Module Parameters
Id:0900d80580975ffbConfidential
ANBA Parameters
7 ANBA Parameters
7.1 VCI (Virtual Channel Identifier)
7.2 VPI (Virtual Path Identifier)
Parameter name Virtual Channel Identifier
Abbreviated name VCI
3GPP name -
Managed Object ANBA
Multiplicity 1
Description Virtual Channel Identifier.
Range 32... 4095
Units -
Formula for getting internal value
internal_value = gui_value
Default value -
Default value notes -
Related functions -
Modification Not modifiable
Related parameters -
Parameter relationships -
Related options -
Feature dependencies -
Interfaces • FTM -> EM • FTM -> RAC
References -
Validation pattern -
Table 25 VCI (Virtual Channel Identifier)
Parameter name Virtual Path Identifier
Abbreviated name VPI
3GPP name -
Managed Object ANBA
Multiplicity 1
Description Virtual Path Identifier.
Table 26 VPI (Virtual Path Identifier)
DN70577885 93
Flexi Transport Module Parameters ANBA Parameters
Id:0900d80580975ffbConfidential
7.3 interfaceNumber (Interface Identifier)
Range 0... 255
Units -
Formula for getting internal value
internal_value = gui_value
Default value -
Default value notes -
Related functions -
Modification Not modifiable
Related parameters -
Parameter relationships -
Related options -
Feature dependencies -
Interfaces • FTM -> EM • FTM -> RAC
References -
Validation pattern -
Table 26 VPI (Virtual Path Identifier) (Cont.)
Parameter name Interface Identifier
Abbreviated name interfaceNumber
3GPP name -
Managed Object ANBA
Multiplicity 1
Description Defines the location on the unit of the physical inter-face that carries the signallink link.
The value depends on the unit type.
FTEB, FTPB, FTIF, FIIF: 1..8
FTIA, FTIB, FTJA, FTLB: 1..4
FTFA, FTHA: 1..16
For IMA, the parameter identifies the IMA group. Values are: 33..75.
For the ATM over Ethernet pseudowire the value is always: 76.
Range 1... 76
Units -
Table 27 interfaceNumber (Interface Identifier)
94 DN70577885
Flexi Transport Module Parameters
Id:0900d80580975ffbConfidential
ANBA Parameters
7.4 nbapTTPId (Upper Layer Path Identifier)
Formula for getting internal value
internal_value = gui_value
Default value -
Default value notes -
Related functions -
Modification Not modifiable
Related parameters -
Parameter relationships -
Related options -
Feature dependencies -
Interfaces • FTM -> EM • FTM -> RAC
References -
Validation pattern -
Table 27 interfaceNumber (Interface Identifier) (Cont.)
Parameter name Upper Layer Path Identifier
Abbreviated name nbapTTPId
3GPP name -
Managed Object ANBA
Multiplicity 1
Table 28 nbapTTPId (Upper Layer Path Identifier)
DN70577885 95
Flexi Transport Module Parameters ANBA Parameters
Id:0900d80580975ffbConfidential
Description Identifies the upper layer path.
The object is identified by
- Unit number (unit#)
- Interface number(if#, imag# or pw#)
- Virtual Path Identifier (vpi#)
- Virtual Channel Identifier (vci#)
Format:
- unit#-if#-vpi#vci# (e.g. 1-8-000C0)
- unit#-imag#-vpi#vci# (e.g. 1-34-00210)
Range:
unit#: 1
if#: 1..16 (maxi. 2 digits)
imag#: 33..75 (2 digits)
pw#: 76
vpi#: 00..FF (hexadecimal number, 2 digits)
vci#: 000..FFF (hexadecimal number, 3 digits)
Range 9...10
Units characters
Formula for getting internal value
internal_value = gui_value
Default value -
Default value notes -
Related functions -
Modification Not modifiable
Related parameters VCI of ANBA - The value of parameter VCI is contained in the value of parame-ter nbapTTPId.
VPI of ANBA - The value of parameter VPI is contained in the value of parame-ter nbapTTPId.
interfaceNumber of ANBA - The value of parameter interfaceNumber is contained in the value of parameter nbapTTPId.
unitNumber of ANBA - The value of parameter unitNumber is contained in the value of parameter nbapTTPId.
Parameter relationships -
Related options -
Feature dependencies -
Table 28 nbapTTPId (Upper Layer Path Identifier) (Cont.)
96 DN70577885
Flexi Transport Module Parameters
Id:0900d80580975ffbConfidential
ANBA Parameters
7.5 nbapType (Upper Layer Connection Type)
Interfaces • EM <-> FTM • RAC -> FTM • RAC <-> RACApp
References -
Validation pattern -
Table 28 nbapTTPId (Upper Layer Path Identifier) (Cont.)
Parameter name Upper Layer Connection Type
Abbreviated name nbapType
3GPP name -
Managed Object ANBA
Multiplicity 1
Description This parameter defines the Upper Layer Connec-tion Type.
In case of a WCDMA environment this is the NBAP type: it can be either C-NBAP or D-NBAP.
In case of an I-HSPA environment, this is the type of traffic converted to IP and then forwarded to the I-HSPA adapter.
The labels AA0 to AA7 are used for AAL5 on FTLB integrated I-HSPA.
Range C_NBAP (0), D_NBAP (1), AA0 (6), AA1 (7), AA2 (8), AA3 (9), AA4 (10), AA5 (11), AA6 (12), AA7 (13)
Units -
Formula for getting internal value
gui ==> internal
C_NBAP ==> 0
D_NBAP ==> 1
AA0 ==> 6
AA1 ==> 7
AA2 ==> 8
AA3 ==> 9
AA4 ==> 10
AA5 ==> 11
AA6 ==> 12
AA7 ==> 13
Table 29 nbapType (Upper Layer Connection Type)
DN70577885 97
Flexi Transport Module Parameters ANBA Parameters
Id:0900d80580975ffbConfidential
7.6 unitNumber (Unit Number)
Default value -
Default value notes -
Related functions -
Modification On-Line
Related parameters iHSPAmode of IPNO - If iHS-PAmode is set to enabled then only the enum values starting with AA are supported.
Parameter relationships -
Related options -
Feature dependencies -
Interfaces • EM <-> FTM • RAC <-> FTM • RAC <-> RACApp
References -
Validation pattern -
Table 29 nbapType (Upper Layer Connection Type) (Cont.)
Parameter name Unit Number
Abbreviated name unitNumber
3GPP name -
Managed Object ANBA
Multiplicity 1
Description Specifies the location of the unit (slot number). In this release it is always 1. The BTS has only 1 unit in slot 1.
Range 1... 1
Units -
Formula for getting internal value
internal_value = gui_value
Default value -
Default value notes -
Related functions -
Modification Not modifiable
Related parameters -
Parameter relationships -
Table 30 unitNumber (Unit Number)
98 DN70577885
Flexi Transport Module Parameters
Id:0900d80580975ffbConfidential
ANBA Parameters
Related options -
Feature dependencies -
Interfaces • FTM -> EM • FTM -> RAC
References -
Validation pattern -
Table 30 unitNumber (Unit Number) (Cont.)
DN70577885 99
Flexi Transport Module Parameters BFD Parameters
Id:0900d80580975ffbConfidential
8 BFD Parameters
8.1 bfdActivation (BFD session activation flag)
Parameter name BFD session activation flag
Abbreviated name bfdActivation
3GPP name -
Managed Object BFD
Multiplicity 1
Description This parameter activates or deactivates the BFD session.
Activate: if set to value true, the transmission of BFD control packets towards the remote peer is started and, in case the BFD session fails, alarms are raised.
Deactivate: if set to value false, the transmission of BFD control packets towards the remote peer is stopped. Also the BTS discards every received BFD packet for a deactivated BFD instance. Moreover all active alarms related to the BFD session are cleared. The BFD session effectively does not exist at all.
Range false (0), true (1)
Units -
Formula for getting internal value
• false => 0 • true => 1
Default value false (0)
Default value notes -
Related functions -
Modification On-Line
Related parameters function of BFD - This parameter is ignored when the value of "function" parameter is OSPF_ALL or OSPF_IP_IF.
Parameter relationships -
Related options • RAN2440 Fast IP Rerouting • RAN1449 Dual Iub for Flexi WCDMA • RAN74 Native Iub IP for Flexi WCDMA BTS
Feature dependencies -
Table 31 bfdActivation (BFD session activation flag)
100 DN70577885
Flexi Transport Module Parameters
Id:0900d80580975ffbConfidential
BFD Parameters
8.2 bfdAdminUp (BFD session admin down state control)
Interfaces • EM <-> FTM • RAC <-> FTM • RAC <-> RACApp
References -
Validation pattern -
Table 31 bfdActivation (BFD session activation flag) (Cont.)
Parameter name BFD session admin down state control
Abbreviated name bfdAdminUp
3GPP name -
Managed Object BFD
Multiplicity 1
Description This parameter controls the admin state of the BFD session.
If set to false, the session enters the "Down" state. Only control messages with state "Admin Down" are sent to the peer. All active alarms of the BFD session are cleared.
If set to true, the session leaves the "Down" state. It will reach the "Up" state if the remote peer is also in "Up" state. If the BFD session fails, alarms are raised for it.
Range false (0), true (1)
Units -
Formula for getting internal value
• false => 0 • true => 1
Default value true (1)
Default value notes -
Related functions -
Modification On-Line
Related parameters -
Parameter relationships -
Related options • RAN74 Native Iub IP for Flexi WCDMA BTS • RAN1449 Dual Iub for Flexi WCDMA • RAN2440 Fast IP Rerouting
Feature dependencies -
Table 32 bfdAdminUp (BFD session admin down state control)
DN70577885 101
Flexi Transport Module Parameters BFD Parameters
Id:0900d80580975ffbConfidential
8.3 bfdDestAddress (Destination IP address for the BFD session)
Interfaces • EM <-> FTM • RAC <-> FTM • RAC <-> RACApp
References -
Validation pattern -
Table 32 bfdAdminUp (BFD session admin down state control) (Cont.)
Parameter name Destination IP address for the BFD session
Abbreviated name bfdDestAddress
3GPP name -
Managed Object BFD
Multiplicity 1
Description This parameter specifies the destination IP address to be used in the BFD session. To be entered in dotted decimal format.
Range 7...15
Units characters
Formula for getting internal value
internal_value = gui_value
Default value -
Default value notes -
Related functions -
Modification On-Line
Related parameters -
Parameter relationships -
Related options • RAN74 Native Iub IP for Flexi WCDMA BTS • RAN1449 Dual Iub for Flexi WCDMA • RAN2440 Fast IP Rerouting
Feature dependencies -
Interfaces • EM <-> FTM • RAC <-> FTM • RAC <-> RACApp
References -
Validation pattern -
Table 33 bfdDestAddress (Destination IP address for the BFD session)
102 DN70577885
Flexi Transport Module Parameters
Id:0900d80580975ffbConfidential
BFD Parameters
8.4 bfdDetectMult (BFD session packets lost detection time multiplier)
Parameter name BFD session packets lost detection time multiplier
Abbreviated name bfdDetectMult
3GPP name -
Managed Object BFD
Multiplicity 1
Description The negotiated BFD control word transmission interval, multiplied by this parameter, provides the detection time for lost packets in the BFD session. Roughly speaking bfdDetectMult is the number of BFD control packets that the FTM may lose in a row, before it shall declare the BFD session to be down.
Range 2... 10
Units -
Formula for getting internal value
internal_value = gui_value
Default value 5
Default value notes -
Related functions -
Modification On-Line
Related parameters -
Parameter relationships -
Related options • RAN74 Native Iub IP for Flexi WCDMA BTS • RAN1449 Dual Iub for Flexi WCDMA • RAN2440 Fast IP Rerouting
Feature dependencies -
Interfaces • EM <-> FTM • RAC <-> FTM • RAC <-> RACApp
References -
Validation pattern -
Table 34 bfdDetectMult (BFD session packets lost detection time multiplier)
DN70577885 103
Flexi Transport Module Parameters BFD Parameters
Id:0900d80580975ffbConfidential
8.5 bfdGrp (BFD group reference)
Parameter name BFD group reference
Abbreviated name bfdGrp
3GPP name -
Managed Object BFD
Multiplicity 1
Description This parameter references the BFD group id to which the BFD session belongs.
The parameter is a managed object instance iden-tifier (LMOID), referencing an instance of object class BFDGRP. The parameter may remain empty, meaning the BFD session is not bound to a BFD group.
Range 0...40
Units characters
Formula for getting internal value
internal_value = gui_value
Default value -
Default value notes Default is the empty string. By default a BFD session is not assigned to any BFD group.
Related functions -
Modification On-Line
Related parameters function of BFD - "bfdGrp" parameter shall not be configured (must be left empty) when "function" parameter has value OSPF_ALL or OSPF_IP_IF
Parameter relationships -
Related options • RAN74 Native Iub IP for Flexi WCDMA BTS • RAN1449 Dual Iub for Flexi WCDMA • RAN2440 Fast IP Rerouting
Feature dependencies -
Interfaces • EM <-> FTM • RAC <-> FTM • RAC <-> RACApp
References -
Validation pattern -
Table 35 bfdGrp (BFD group reference)
104 DN70577885
Flexi Transport Module Parameters
Id:0900d80580975ffbConfidential
BFD Parameters
8.6 bfdId (BFD session identifier)
8.7 bfdSourceIpAddr (Source IP address for the BFD session)
Parameter name BFD session identifier
Abbreviated name bfdId
3GPP name -
Managed Object BFD
Multiplicity 1
Description This parameter identifies a BFD session.
Range 1... 16
Units -
Formula for getting internal value
internal_value = gui_value
Default value -
Default value notes -
Related functions -
Modification Not modifiable
Related parameters -
Parameter relationships -
Related options • RAN74 Native Iub IP for Flexi WCDMA BTS • RAN1449 Dual Iub for Flexi WCDMA • RAN2440 Fast IP Rerouting
Feature dependencies -
Interfaces • EM <-> FTM • RAC -> FTM • RAC <-> RACApp
References -
Validation pattern -
Table 36 bfdId (BFD session identifier)
Parameter name Source IP address for the BFD session
Abbreviated name bfdSourceIpAddr
3GPP name -
Managed Object BFD
Multiplicity 1
Table 37 bfdSourceIpAddr (Source IP address for the BFD session)
DN70577885 105
Flexi Transport Module Parameters BFD Parameters
Id:0900d80580975ffbConfidential
8.8 bfdSourceUdpPort (UDP source port of the BFD session)
Description This parameter specifies the source IP address to be used in BFD messages for the BFD session. This can be a network interface IP address or a virtual IP address.
To be entered in dotted decimal format.
Range 7...15
Units characters
Formula for getting internal value
internal_value = gui_value
Default value -
Default value notes -
Related functions -
Modification On-Line
Related parameters -
Parameter relationships -
Related options • RAN74 Native Iub IP for Flexi WCDMA BTS • RAN1449 Dual Iub for Flexi WCDMA • RAN2440 Fast IP Rerouting
Feature dependencies -
Interfaces • EM <-> FTM • RAC <-> FTM • RAC <-> RACApp
References -
Validation pattern -
Table 37 bfdSourceIpAddr (Source IP address for the BFD session) (Cont.)
Parameter name UDP source port of the BFD session
Abbreviated name bfdSourceUdpPort
3GPP name -
Managed Object BFD
Multiplicity 1
Table 38 bfdSourceUdpPort (UDP source port of the BFD session)
106 DN70577885
Flexi Transport Module Parameters
Id:0900d80580975ffbConfidential
BFD Parameters
8.9 bfdType (BFD session type)
Description This parameter specifies the UDP source port to be used in the BFD session.
Note: value range and default value depend on the BFD type.
- For Multi Hop BFD, the value range is 4784, 49152...65535 and the default value = 4784.
- For Single Hop BFD the value range is 3784, 49152...65535 and the default value = 3784.
NOTE: Service will be temporarily impacted because of modification of this parameter. Hence it is better not to modify this during peak hours.
Range 3784... 65535
Units -
Formula for getting internal value
internal_value = gui_value
Default value 4784
Default value notes Since the default value of BFD Type is Multi Hop BFD, the default BFD UDP source port is 4784.
Related functions -
Modification Cell shutdown needed
Related parameters bfdType of BFD - - For Multi Hop BFD, the value range is 4784, 49152...65535 and the default value = 4784.
Parameter relationships -
Related options • RAN74 Native Iub IP for Flexi WCDMA BTS • RAN1449 Dual Iub for Flexi WCDMA • RAN2440 Fast IP Rerouting
Feature dependencies -
Interfaces • EM <-> FTM • RAC <-> FTM • RAC <-> RACApp
References -
Validation pattern -
Table 38 bfdSourceUdpPort (UDP source port of the BFD session) (Cont.)
Parameter name BFD session type
Abbreviated name bfdType
Table 39 bfdType (BFD session type)
DN70577885 107
Flexi Transport Module Parameters BFD Parameters
Id:0900d80580975ffbConfidential
8.10 desMinTxInt (Desired minimum BFD control word transmit interval)
3GPP name -
Managed Object BFD
Multiplicity 1
Description This parameter specifies the type of the BFD session: Single Hop or Multi Hop BFD.
Range singleHopBFD (0), multiHopBFD (1)
Units -
Formula for getting internal value
gui ==> internal
singleHopBFD ==> 0
multiHopBFD ==> 1
Default value multiHopBFD (1)
Default value notes -
Related functions -
Modification On-Line
Related parameters -
Parameter relationships -
Related options • RAN74 Native Iub IP for Flexi WCDMA BTS • RAN1449 Dual Iub for Flexi WCDMA • RAN2440 Fast IP Rerouting
Feature dependencies -
Interfaces • EM <-> FTM • RAC <-> FTM • RAC <-> RACApp
References -
Validation pattern -
Table 39 bfdType (BFD session type) (Cont.)
Parameter name Desired minimum BFD control word transmit interval
Abbreviated name desMinTxInt
3GPP name -
Managed Object BFD
Multiplicity 1
Table 40 desMinTxInt (Desired minimum BFD control word transmit interval)
108 DN70577885
Flexi Transport Module Parameters
Id:0900d80580975ffbConfidential
BFD Parameters
8.11 function (BFD session function definition)
Description This parameter specifies the minimum interval, that the FTM would like to use when transmitting BFD control packets for the BFD session.
Range 100... 5000
Units ms
Formula for getting internal value
internal_value = gui_value
Default value 500
Default value notes -
Related functions -
Modification On-Line
Related parameters -
Parameter relationships -
Related options • RAN74 Native Iub IP for Flexi WCDMA BTS • RAN1449 Dual Iub for Flexi WCDMA • RAN2440 Fast IP Rerouting
Feature dependencies -
Interfaces • EM <-> FTM • RAC <-> FTM • RAC <-> RACApp
References -
Validation pattern -
Table 40 desMinTxInt (Desired minimum BFD control word transmit interval) (Cont.)
Parameter name BFD session function definition
Abbreviated name function
3GPP name -
Managed Object BFD
Multiplicity 1
Table 41 function (BFD session function definition)
DN70577885 109
Flexi Transport Module Parameters BFD Parameters
Id:0900d80580975ffbConfidential
Description This parameter defines for which purpose BFD session is used.
If value is set to MANUAL_BFD_SESSION both, bfdSourceIpAddr and bfdDestAddress have to be specified.
If value is set to OSPF_ALL for both, bfdSourceI-pAddr and bfdDestAddress the value has to be set to 0.0.0.0.
If value is set to OSPF_IP_IF the value for bfdSour-ceIpAddr shall match the value of the IP interface used for OSPF. The value for bfdDestAddress has to be set to 0.0.0.0.
Range MANUAL_BFD_SESSION (0), OSPF_ALL (1), OSPF_IP_IF (2)
Units -
Formula for getting internal value
gui ==> internal
MANUAL_BFD_SESSION ==> 0
OSPF_ALL ==> 1
OSPF_IP_IF ==> 2
Default value MANUAL_BFD_SESSION (0)
Default value notes -
Related functions -
Modification On-Line
Related parameters unitTypeExpected of UNIT - Since OSPF is not supported on all HW variants, for the HW modules FTEB, FTHA, FTPB, FTFA the only supported value is "MANUAL_BFD_SESSION".
Parameter relationships -
Related options • RAN2440 Fast IP Rerouting • RAN2359 OSPF enhancements
Feature dependencies -
Interfaces • FTM <-> RAC • FTM <-> EM • RACApp <-> RAC
References -
Validation pattern -
Table 41 function (BFD session function definition) (Cont.)
110 DN70577885
Flexi Transport Module Parameters
Id:0900d80580975ffbConfidential
BFD Parameters
8.12 reqMinRxInt (Required minimum BFD control word receive interval)
Parameter name Required minimum BFD control word receive interval
Abbreviated name reqMinRxInt
3GPP name -
Managed Object BFD
Multiplicity 1
Description This parameter specifies the minimum interval between received BFD control packets that the FTM shall support for the BFD session.
Range 100... 5000
Units ms
Formula for getting internal value
internal_value = gui_value
Default value 500
Default value notes -
Related functions -
Modification On-Line
Related parameters -
Parameter relationships -
Related options • RAN74 Native Iub IP for Flexi WCDMA BTS • RAN1449 Dual Iub for Flexi WCDMA • RAN2440 Fast IP Rerouting
Feature dependencies -
Interfaces • EM <-> FTM • RAC <-> FTM • RAC <-> RACApp
References -
Validation pattern -
Table 42 reqMinRxInt (Required minimum BFD control word receive interval)
DN70577885 111
Flexi Transport Module Parameters BFDGRP Parameters
Id:0900d80580975ffbConfidential
9 BFDGRP Parameters
9.1 bfdGrpId (BFD Group Identifier )
Parameter name BFD Group Identifier
Abbreviated name bfdGrpId
3GPP name -
Managed Object BFDGRP
Multiplicity 1
Description This parameter identifies a BFD group.
Range 1... 8
Units -
Formula for getting internal value
internal_value = gui_value
Default value -
Default value notes -
Related functions -
Modification Not modifiable
Related parameters -
Parameter relationships -
Related options • RAN74 Native Iub IP for Flexi WCDMA BTS • RAN1449 Dual Iub for Flexi WCDMA • RAN2440 Fast IP Rerouting
Feature dependencies -
Interfaces • EM <-> FTM • RAC -> FTM • RAC <-> RACApp
References -
Validation pattern -
Table 43 bfdGrpId (BFD Group Identifier )
112 DN70577885
Flexi Transport Module Parameters
Id:0900d80580975ffbConfidential
CCFA Parameters
10 CCFA Parameters
10.1 atmFabricId (ATM Fabric Identifier)
Parameter name ATM Fabric Identifier
Abbreviated name atmFabricId
3GPP name -
Managed Object CCFA
Multiplicity 1
Description Since in Flexi there are no actual ATM cross con-nections, the MO ATM Fabric is a dummy, intro-duced just to keep the attribute ubrPlusEnabled on the same place as in AXC.
This parameter identifies the ATM Fabric configura-tion. Values is always 1: Exactly 1 instance of ATM Fabric exists on the BTS.
Range 1... 1
Units -
Formula for getting internal value
internal_value = gui_value
Default value -
Default value notes -
Related functions -
Modification Not modifiable
Related parameters -
Parameter relationships -
Related options -
Feature dependencies -
Interfaces • EM <-> FTM • RAC -> FTM • RAC <-> RACApp
References -
Validation pattern -
Table 44 atmFabricId (ATM Fabric Identifier)
DN70577885 113
Flexi Transport Module Parameters CCFA Parameters
Id:0900d80580975ffbConfidential
10.2 ubrPlusEnabled (UBR+ Enabled)
Parameter name UBR+ Enabled
Abbreviated name ubrPlusEnabled
3GPP name -
Managed Object CCFA
Multiplicity 1
Description This attribute is used to explicitly enable (TRUE) or disable (FALSE) the network element to take UBR+ into use. If set to FALSE then the network element ingnores MDCR and UBRshare parameters in the TRDE.
If set to TRUE, the network element uses MDCR and UBR share for UBR+ connection traffic man-agement scheduling. If TRUE and MDCR and UBRshare are not given then the network element shall take the default values for MDCR and UBR-share. The usage of UBR+ requires the availability of a licence.
Range false (0), true (1)
Units -
Formula for getting internal value
• false => 0 • true => 1
Default value false (0)
Default value notes -
Related functions -
Modification On-Line
Related parameters -
Parameter relationships -
Related options -
Feature dependencies • ATM Traffic Management: UBR (Unspecified Bit Rate), CBR (Constant Bit Rate), Shaping
Interfaces • EM <-> FTM • RAC <-> FTM • RAC <-> RACApp
References -
Validation pattern -
Table 45 ubrPlusEnabled (UBR+ Enabled)
114 DN70577885
Flexi Transport Module Parameters
Id:0900d80580975ffbConfidential
CCFA Parameters
10.3 vccBundleEnabled (VCC Bundle Enabling Flag)
Parameter name VCC Bundle Enabling Flag
Abbreviated name vccBundleEnabled
3GPP name -
Managed Object CCFA
Multiplicity 1
Description This parameter enables VCC bundling for collecting extra bandwidth unused by neighbour VCCs.
Range false (0), true (1)
Units -
Formula for getting internal value
• false => 0 • true => 1
Default value false (0)
Default value notes -
Related functions -
Modification On-Line
Related parameters -
Parameter relationships -
Related options -
Feature dependencies • CR 1406 Improvements for VCC bundle
Interfaces • EM <-> FTM • RAC <-> FTM • RAC <-> RACApp
References -
Validation pattern -
Table 46 vccBundleEnabled (VCC Bundle Enabling Flag)
DN70577885 115
Flexi Transport Module Parameters CERTH Parameters
Id:0900d80580975ffbConfidential
11 CERTH Parameters
11.1 btsCertificateUpdateTime (BTS certificate update time)
11.2 caCertificateUpdateTime (CA certificate update time)
Parameter name BTS certificate update time
Abbreviated name btsCertificateUpdateTime
3GPP name -
Managed Object CERTH
Multiplicity 1
Description This parameter specifies how many days in advance to the BTS certificate expiry date, the FTM shall execute a CMP update.
Range 1... 4999
Units days
Formula for getting internal value
internal_value = gui_value
Default value 30
Default value notes Default value is 1 month.
Related functions -
Modification On-Line
Related parameters -
Parameter relationships -
Related options • RAN1899 Factory and Customer PKI
Feature dependencies -
Interfaces • EM <-> FTM • RAC <-> FTM • RAC <-> RACApp
References -
Validation pattern -
Table 47 btsCertificateUpdateTime (BTS certificate update time)
Parameter name CA certificate update time
Abbreviated name caCertificateUpdateTime
3GPP name -
Table 48 caCertificateUpdateTime (CA certificate update time)
116 DN70577885
Flexi Transport Module Parameters
Id:0900d80580975ffbConfidential
CERTH Parameters
11.3 caSubjectName (CMP server subject name)
Managed Object CERTH
Multiplicity 1
Description This parameter specifies how many days in advance to the CA or Trust Anchor certificate expiry date, the FTM shall execute a CMP update.
Range 1... 4999
Units days
Formula for getting internal value
internal_value = gui_value
Default value 180
Default value notes Default value is 6 months.
Related functions -
Modification On-Line
Related parameters -
Parameter relationships -
Related options • RAN1899 Factory and Customer PKI
Feature dependencies -
Interfaces • EM <-> FTM • RAC <-> FTM • RAC <-> RACApp
References -
Validation pattern -
Table 48 caCertificateUpdateTime (CA certificate update time) (Cont.)
Parameter name CMP server subject name
Abbreviated name caSubjectName
3GPP name -
Managed Object CERTH
Multiplicity 1
Description This parameter identifies the CMP server by its subject name. It may either be detected by DHCP upon autoconnection or configured by the manage-ment system.
Range 0...128
Units characters
Table 49 caSubjectName (CMP server subject name)
DN70577885 117
Flexi Transport Module Parameters CERTH Parameters
Id:0900d80580975ffbConfidential
11.4 certhId (Certification Handler Identifier)
Formula for getting internal value
internal_value = gui_value
Default value -
Default value notes Length value 0 means CA subject name is not con-figured
Related functions -
Modification On-Line
Related parameters -
Parameter relationships -
Related options • RAN963 Network Element Certificate Manage-ment
Feature dependencies -
Interfaces • EM <-> FTM • RAC <-> FTM • RAC <-> RACApp
References -
Validation pattern -
Table 49 caSubjectName (CMP server subject name) (Cont.)
Parameter name Certification Handler Identifier
Abbreviated name certhId
3GPP name -
Managed Object CERTH
Multiplicity 1
Description This parameter identifies the certificate handler configuration. The value is always 1.
Range 1... 1
Units -
Formula for getting internal value
internal_value = gui_value
Default value -
Default value notes -
Related functions -
Modification Not modifiable
Related parameters -
Table 50 certhId (Certification Handler Identifier)
118 DN70577885
Flexi Transport Module Parameters
Id:0900d80580975ffbConfidential
CERTH Parameters
11.5 cmpServerIpAddress (CMP Server IP Address)
Parameter relationships -
Related options • RAN963 Network Element Certificate Manage-ment
Feature dependencies -
Interfaces • EM <-> FTM • RAC -> FTM • RAC <-> RACApp
References -
Validation pattern -
Table 50 certhId (Certification Handler Identifier) (Cont.)
Parameter name CMP Server IP Address
Abbreviated name cmpServerIpAddress
3GPP name -
Managed Object CERTH
Multiplicity 1
Description This is the IP address of the Certificate Manage-ment Protocol server. To be entered in dotted decimal format.
Range 7...15
Units characters
Formula for getting internal value
internal_value = gui_value
Default value -
Default value notes -
Related functions -
Modification On-Line
Related parameters -
Parameter relationships -
Related options • RAN963 Network Element Certificate Manage-ment
Feature dependencies -
Interfaces • EM <-> FTM • RAC <-> FTM • RAC <-> RACApp
Table 51 cmpServerIpAddress (CMP Server IP Address)
DN70577885 119
Flexi Transport Module Parameters CERTH Parameters
Id:0900d80580975ffbConfidential
11.6 cmpServerPort (CMP Server Port)
11.7 crServerIpAddress (CR Server IP Address)
References -
Validation pattern -
Table 51 cmpServerIpAddress (CMP Server IP Address) (Cont.)
Parameter name CMP Server Port
Abbreviated name cmpServerPort
3GPP name -
Managed Object CERTH
Multiplicity 1
Description This is the port number to be used for addressing the Certificate Management Protocol server.
Range 1... 65535
Units -
Formula for getting internal value
internal_value = gui_value
Default value 1024
Default value notes -
Related functions -
Modification On-Line
Related parameters -
Parameter relationships -
Related options • RAN963 Network Element Certificate Manage-ment
Feature dependencies -
Interfaces • EM <-> FTM • RAC <-> FTM • RAC <-> RACApp
References -
Validation pattern -
Table 52 cmpServerPort (CMP Server Port)
Parameter name CR Server IP Address
Table 53 crServerIpAddress (CR Server IP Address)
120 DN70577885
Flexi Transport Module Parameters
Id:0900d80580975ffbConfidential
CERTH Parameters
11.8 crServerPort (CR Server Port)
Abbreviated name crServerIpAddress
3GPP name -
Managed Object CERTH
Multiplicity 1
Description This is the IP Address of the CR Server in dotted decimal format.
Range 7...15
Units characters
Formula for getting internal value
internal_value = gui_value
Default value -
Default value notes -
Related functions -
Modification On-Line
Related parameters -
Parameter relationships -
Related options • RAN963 Network Element Certificate Manage-ment
Feature dependencies -
Interfaces • EM <-> FTM • RAC <-> FTM • RAC <-> RACApp
References -
Validation pattern -
Table 53 crServerIpAddress (CR Server IP Address) (Cont.)
Parameter name CR Server Port
Abbreviated name crServerPort
3GPP name -
Managed Object CERTH
Multiplicity 1
Description This is the port number to be used for addressing the CR server in certificate management.
Range 1... 65535
Table 54 crServerPort (CR Server Port)
DN70577885 121
Flexi Transport Module Parameters CERTH Parameters
Id:0900d80580975ffbConfidential
11.9 crlUpdatePeriod (Certificate Revocation List update period)
Units -
Formula for getting internal value
internal_value = gui_value
Default value -
Default value notes -
Related functions -
Modification On-Line
Related parameters -
Parameter relationships -
Related options • RAN963 Network Element Certificate Manage-ment
Feature dependencies -
Interfaces • EM <-> FTM • RAC <-> FTM • RAC <-> RACApp
References -
Validation pattern -
Table 54 crServerPort (CR Server Port) (Cont.)
Parameter name Certificate Revocation List update period
Abbreviated name crlUpdatePeriod
3GPP name -
Managed Object CERTH
Multiplicity 1
Description This parameter specifies the regular period for exe-cuting a periodical update of the Certificate Revo-cation List. In hours. Value 0 means "no periodical update".
Range 0... 8760
Units -
Formula for getting internal value
internal_value = gui_value
Default value 0
Default value notes No periodical update.
Table 55 crlUpdatePeriod (Certificate Revocation List update period)
122 DN70577885
Flexi Transport Module Parameters
Id:0900d80580975ffbConfidential
CERTH Parameters
Related functions -
Modification On-Line
Related parameters -
Parameter relationships -
Related options -
Feature dependencies • CN4065
Interfaces • EM <-> FTM • RAC <-> FTM • RAC <-> RACApp
References -
Validation pattern -
Table 55 crlUpdatePeriod (Certificate Revocation List update period) (Cont.)
DN70577885 123
Flexi Transport Module Parameters CESIF Parameters
Id:0900d80580975ffbConfidential
12 CESIF Parameters
12.1 cesMinUDPPort (CES over PSN source port value range)
Parameter name CES over PSN source port value range
Abbreviated name cesMinUDPPort
3GPP name -
Managed Object CESIF
Multiplicity 1
Description This parameter defines the range of the source port numbers that shall be used for CES over PSN. The parameter defines the lower value of that range. This port and the subsequent ports are used for the CES over PSN pseudowires.
Also a remote UDP port number is defined for each CES over PSN pseudowire. Local and remote port may but don't have to be different.
It shall be ensured that CES over PSN ports are not configured for other purposes. i.e. other pseudowires or 3G traffic types.
Range 49152... 65532
Units -
Formula for getting internal value
internal_value = gui_value
Default value -
Default value notes -
Related functions -
Modification On-Line
Related parameters -
Parameter relationships -
Related options • RAN1707 Flexi WCDMA Integrated CESoPSN
Feature dependencies -
Interfaces • EM <-> FTM • RAC <-> FTM • RAC <-> RACApp
References -
Validation pattern -
Table 56 cesMinUDPPort (CES over PSN source port value range)
124 DN70577885
Flexi Transport Module Parameters
Id:0900d80580975ffbConfidential
CESIF Parameters
12.2 cesifId (CES over PSN interface identifier)
Parameter name CES over PSN interface identifier
Abbreviated name cesifId
3GPP name -
Managed Object CESIF
Multiplicity 1
Description This parameter identified the CES over PSN inter-face. Its value is always 1.
Range 1... 1
Units -
Formula for getting internal value
internal_value = gui_value
Default value -
Default value notes -
Related functions -
Modification Not modifiable
Related parameters -
Parameter relationships -
Related options • RAN1707 Flexi WCDMA Integrated CESoPSN
Feature dependencies -
Interfaces • EM <-> FTM • RAC -> FTM • RAC <-> RACApp
References -
Validation pattern -
Table 57 cesifId (CES over PSN interface identifier)
DN70577885 125
Flexi Transport Module Parameters CESPW Parameters
Id:0900d80580975ffbConfidential
13 CESPW Parameters
13.1 administrativeState (Administrative state)
Parameter name Administrative state
Abbreviated name administrativeState
3GPP name -
Managed Object CESPW
Multiplicity 1
Description This parameter is used to lock and unlock the CES over PSN pseudowire.
Locking the pseudowire switches the CES function-ality off. Also all CES over PSN related alarms are suppressed.
Range locked (0), unlocked (1)
Units -
Formula for getting internal value
gui ==> internal
locked ==> 0
unlocked ==> 1
Default value locked (0)
Default value notes -
Related functions -
Modification On-Line
Related parameters administrativeState of P3SL - The features CES over PSN and Single Link PPP cannot be operated together.
administrativeState of P3ML - The features CES over PSN and Multi Link PPP cannot be operated together.
Parameter relationships -
Related options • RAN1707 Flexi WCDMA Integrated CESoPSN
Feature dependencies -
Interfaces • EM <-> FTM • RAC <-> FTM • RAC <-> RACApp
References -
Validation pattern -
Table 58 administrativeState (Administrative state)
126 DN70577885
Flexi Transport Module Parameters
Id:0900d80580975ffbConfidential
CESPW Parameters
13.2 cesPWid (CES over PSN Pseudowire Identifier)
Parameter name CES over PSN Pseudowire Identifier
Abbreviated name cesPWid
3GPP name -
Managed Object CESPW
Multiplicity 1
Description This parameter identifies the CES over PSN pseudowire.
The format of the parameter is slot#-if#
where slot# is the slot of the unit where the interface resides and if# is the interface number of the corre-sponding PDH interface on this unit.
In this release slot is always 1.
The value range of the if# part of the parameter depends on the hardware:
FIIB, FILB, FTIB, FTLB: 1..4
FTIF, FIIF: 1..8
FTFB: 1..16
Range 3...4
Units characters
Formula for getting internal value
internal_value = gui_value
Default value -
Default value notes -
Related functions -
Modification Not modifiable
Related parameters -
Parameter relationships -
Related options • RAN1707 Flexi WCDMA Integrated CESoPSN
Feature dependencies -
Interfaces • EM <-> FTM • RAC -> FTM • RAC <-> RACApp
References -
Validation pattern -
Table 59 cesPWid (CES over PSN Pseudowire Identifier)
DN70577885 127
Flexi Transport Module Parameters CESPW Parameters
Id:0900d80580975ffbConfidential
13.3 dscp (DSCP value)
13.4 framesNumber (Number of frames per CESoPSN packet)
Parameter name DSCP value
Abbreviated name dscp
3GPP name -
Managed Object CESPW
Multiplicity 1
Description This is the Diff Serve Code Point value that shall be inserted into the traffic that is running over this CES over PSN pseudowire.
Range 0... 63
Units -
Formula for getting internal value
internal_value = gui_value
Default value 46
Default value notes This corresponds to the Per Hop Behaviour for Expedited Forwarding (EF).
Related functions -
Modification On-Line
Related parameters -
Parameter relationships -
Related options • RAN1707 Flexi WCDMA Integrated CESoPSN
Feature dependencies -
Interfaces • EM <-> FTM • RAC <-> FTM • RAC <-> RACApp
References -
Validation pattern -
Table 60 dscp (DSCP value)
Parameter name Number of frames per CESoPSN packet
Abbreviated name framesNumber
3GPP name -
Managed Object CESPW
Multiplicity 1
Table 61 framesNumber (Number of frames per CESoPSN packet)
128 DN70577885
Flexi Transport Module Parameters
Id:0900d80580975ffbConfidential
CESPW Parameters
13.5 jitterBufferSize (Jitter Buffer Size)
Description This parameter holds the number of frames per CES over PSN packet.
Note: the number of frames per packet multiplied by the number of PDH timeslots (parameter payload-Timeslots) shall be between 40 and 1536. Other-wise the resulting CESoPSN packet size is violating the allowed ethernet packet size and the CES con-nection cannot be established.
Range 2... 32
Units -
Formula for getting internal value
internal_value = gui_value
Default value 8
Default value notes -
Related functions -
Modification On-Line
Related parameters payloadTimeslots of CESPW - The number of frames per packet multiplied by the number of PDH timeslots (parameter payload-Timeslots) shall be between 40 and 1536. Other-wise the resulting CESoPSN packet size is violating the allowed ethernet packet size and the CES con-nection cannot be established.
Parameter relationships -
Related options • RAN1707 Flexi WCDMA Integrated CESoPSN
Feature dependencies -
Interfaces • EM <-> FTM • RAC <-> FTM • RAC <-> RACApp
References -
Validation pattern -
Table 61 framesNumber (Number of frames per CESoPSN packet) (Cont.)
Parameter name Jitter Buffer Size
Abbreviated name jitterBufferSize
3GPP name -
Managed Object CESPW
Table 62 jitterBufferSize (Jitter Buffer Size)
DN70577885 129
Flexi Transport Module Parameters CESPW Parameters
Id:0900d80580975ffbConfidential
13.6 payloadTimeslots (Payload timeslots of TDM frame)
Multiplicity 1
Description This parameter holds the jitter buffer size to be used by the LLP to equalize the packet delay variation on the network for this pseudowire.
Unit: the value of the parameter is used as +/- x mil-liseconds, meaning that packets x ms too late or x ms too early still fit into the jitter buffer.
Value range is +/- 125 microseconds to +/- 64 milli-seconds.
A higher value allows equalizing more jitter but increases the end-to-end delay.
Range 500... 64000
Units microseconds
Formula for getting internal value
internal_value = gui_value
Default value 8000
Default value notes -
Related functions -
Modification On-Line
Related parameters -
Parameter relationships -
Related options • RAN1707 Flexi WCDMA Integrated CESoPSN
Feature dependencies -
Interfaces • EM <-> FTM • RAC <-> FTM • RAC <-> RACApp
References -
Validation pattern -
Table 62 jitterBufferSize (Jitter Buffer Size) (Cont.)
Parameter name Payload timeslots of TDM frame
Abbreviated name payloadTimeslots
3GPP name -
Managed Object CESPW
Multiplicity 31
Table 63 payloadTimeslots (Payload timeslots of TDM frame)
130 DN70577885
Flexi Transport Module Parameters
Id:0900d80580975ffbConfidential
CESPW Parameters
Description This parameter defines which timeslots from each TDM frame are used to form the packet payload for CES over PSN over this pseudowire. The set of configured timeslots may be an arbitrary one. It does not have to be contiguous.
Note that timeslot 0 is never transmitted.
Range: [1...31] for E1 and [1...24] for T1/JT1.
Note: the number of timeslots multiplied by the number of frames per packet (parameter fra-mesNumber) shall be between 40 and 1536. Other-wise the resulting CESoPSN packet size is violating the allowed ethernet packet size and the CES con-nection cannot be established.
Range TS1 (1), TS2 (2), TS3 (3), TS4 (4), TS5 (5), TS6 (6), TS7 (7), TS8 (8), TS9 (9), TS10 (10), TS11 (11), TS12 (12), TS13 (13), TS14 (14), TS15 (15), TS16 (16), TS17 (17), TS18 (18), TS19 (19), TS20 (20), TS21 (21), TS22 (22), TS23 (23), TS24 (24), TS25 (25), TS26 (26), TS27 (27), TS28 (28), TS29 (29), TS30 (30), TS31 (31)
Units -
Table 63 payloadTimeslots (Payload timeslots of TDM frame) (Cont.)
DN70577885 131
Flexi Transport Module Parameters CESPW Parameters
Id:0900d80580975ffbConfidential
Formula for getting internal value
gui ==> internal
TS1 ==> 1
TS2 ==> 2
TS3 ==> 3
TS4 ==> 4
TS5 ==> 5
TS6 ==> 6
TS7 ==> 7
TS8 ==> 8
TS9 ==> 9
TS10 ==> 10
TS11 ==> 11
TS12 ==> 12
TS13 ==> 13
TS14 ==> 14
TS15 ==> 15
TS16 ==> 16
TS17 ==> 17
TS18 ==> 18
TS19 ==> 19
TS20 ==> 20
TS21 ==> 21
TS22 ==> 22
TS23 ==> 23
TS24 ==> 24
TS25 ==> 25
TS26 ==> 26
TS27 ==> 27
TS28 ==> 28
TS29 ==> 29
TS30 ==> 30
TS31 ==> 31
Default value -
Default value notes -
Related functions -
Modification On-Line
Table 63 payloadTimeslots (Payload timeslots of TDM frame) (Cont.)
132 DN70577885
Flexi Transport Module Parameters
Id:0900d80580975ffbConfidential
CESPW Parameters
13.7 remoteUDPPort (Remote UDP port number for CES over PSN)
Related parameters framesNumber of CESPW - The number of timeslots multiplied by the number of frames per packet (parameter framesNumber) shall be between 40 and 1536. Otherwise the resulting CESoPSN packet size is violating the allowed ethernet packet size and the CES connection cannot be established.
Parameter relationships -
Related options • RAN1707 Flexi WCDMA Integrated CESoPSN
Feature dependencies -
Interfaces • EM <-> FTM • RAC <-> FTM • RAC <-> RACApp
References -
Validation pattern -
Table 63 payloadTimeslots (Payload timeslots of TDM frame) (Cont.)
Parameter name Remote UDP port number for CES over PSN
Abbreviated name remoteUDPPort
3GPP name -
Managed Object CESPW
Multiplicity 1
Description This is the number of the remote UDP port to be used for running traffic on the CES over PSN pseudowire. The remote port is used to identify packets belonging to this pseudowire.
Also a local UDP port number is defined for this CES pseudowire. Local and remote port may but don't have to be different.
It shall be ensured that both ports are not config-ured for other purposes. i.e. other pseudowires or 3G traffic types.
Range 49152... 65535
Units -
Formula for getting internal value
internal_value = gui_value
Table 64 remoteUDPPort (Remote UDP port number for CES over PSN)
DN70577885 133
Flexi Transport Module Parameters CESPW Parameters
Id:0900d80580975ffbConfidential
Default value -
Default value notes -
Related functions -
Modification On-Line
Related parameters -
Parameter relationships -
Related options • RAN1707 Flexi WCDMA Integrated CESoPSN
Feature dependencies -
Interfaces • EM <-> FTM • RAC <-> FTM • RAC <-> RACApp
References -
Validation pattern -
Table 64 remoteUDPPort (Remote UDP port number for CES over PSN) (Cont.)
134 DN70577885
Flexi Transport Module Parameters
Id:0900d80580975ffbConfidential
CESPWT Parameters
14 CESPWT Parameters
14.1 cesPWTid (CES over PSN pseudowire tunnel identifier)
14.2 destIpAddress (Destination IP address)
Parameter name CES over PSN pseudowire tunnel identifier
Abbreviated name cesPWTid
3GPP name -
Managed Object CESPWT
Multiplicity 1
Description This parameter identifies the CES over PSN pseudowire tunnel. Its value is always 1. Currently only 1 pseudowire tunnel can be configured for CES over PSN.
Range 1... 1
Units -
Formula for getting internal value
internal_value = gui_value
Default value -
Default value notes -
Related functions -
Modification Not modifiable
Related parameters -
Parameter relationships -
Related options • RAN1707 Flexi WCDMA Integrated CESoPSN
Feature dependencies -
Interfaces • EM <-> FTM • RAC -> FTM • RAC <-> RACApp
References -
Validation pattern -
Table 65 cesPWTid (CES over PSN pseudowire tunnel identifier)
Parameter name Destination IP address
Abbreviated name destIpAddress
3GPP name -
Table 66 destIpAddress (Destination IP address)
DN70577885 135
Flexi Transport Module Parameters CESPWT Parameters
Id:0900d80580975ffbConfidential
Managed Object CESPWT
Multiplicity 1
Description This is the destination IP address of the packets belonging to the CES over PSN pseudowire tunnel.
This is an IPv4 IP address in dotted decimal format.
Range 7...15
Units characters
Formula for getting internal value
internal_value = gui_value
Default value -
Default value notes -
Related functions -
Modification On-Line
Related parameters -
Parameter relationships -
Related options • RAN1707 Flexi WCDMA Integrated CESoPSN
Feature dependencies -
Interfaces • EM <-> FTM • RAC <-> FTM • RAC <-> RACApp
References -
Validation pattern -
Table 66 destIpAddress (Destination IP address) (Cont.)
136 DN70577885
Flexi Transport Module Parameters
Id:0900d80580975ffbConfidential
ETHLK Parameters
15 ETHLK Parameters
15.1 acceptableFrameTypes (Switch Port Acceptable Frame Types)
Parameter name Switch Port Acceptable Frame Types
Abbreviated name acceptableFrameTypes
3GPP name -
Managed Object ETHLK
Multiplicity 1
Description If the value of acceptableFrameTypes is "Admit-Tagged", the device will discard untagged and Priority-tagged frames received on this interface. If the value is “AdmitAll”, tagged, untagged and Priority-tagged frames received on this interface will be accepted. Untagged and Priority-tagged frames are assigned to the VLAN defined by the portDefaultVlanId for this interface
Range ADMIT_ALL (0), ADMIT_TAGGED (1)
Units -
Formula for getting internal value
gui ==> internal
ADMIT_ALL ==> 0
ADMIT_TAGGED ==> 1
Default value ADMIT_ALL (0)
Default value notes -
Related functions -
Modification On-Line
Related parameters -
Parameter relationships -
Related options • RAN1769 Ethernet Switching
Feature dependencies -
Interfaces • EM <-> FTM • RAC <-> FTM • RAC <-> RACApp
References NSN reference: CN4420 QoS-VLAN Ethernet switching improvement
Validation pattern -
Table 67 acceptableFrameTypes (Switch Port Acceptable Frame Types)
DN70577885 137
Flexi Transport Module Parameters ETHLK Parameters
Id:0900d80580975ffbConfidential
15.2 administrativeState (Administrative State)
15.3 ethLinkId (Ethernet Link Identifier)
Parameter name Administrative State
Abbreviated name administrativeState
3GPP name -
Managed Object ETHLK
Multiplicity 1
Description This parameter is used to lock and unlock the inter-face.
Locking the interface deactivates it and all alarms and any traffic over the interface is suppressed.
NOTE:Ethernet interface cannot be in use (unlocked) in the ATM Iub transport mode for FTFB, FTIF, and FIIF
Range locked (0), unlocked (1)
Units -
Formula for getting internal value
gui ==> internal
locked ==> 0
unlocked ==> 1
Default value locked (0)
Default value notes -
Related functions -
Modification On-Line
Related parameters -
Parameter relationships -
Related options -
Feature dependencies -
Interfaces • EM <-> FTM • RAC <-> FTM • RAC <-> RACApp
References -
Validation pattern -
Table 68 administrativeState (Administrative State)
Parameter name Ethernet Link Identifier
Table 69 ethLinkId (Ethernet Link Identifier)
138 DN70577885
Flexi Transport Module Parameters
Id:0900d80580975ffbConfidential
ETHLK Parameters
Abbreviated name ethLinkId
3GPP name -
Managed Object ETHLK
Multiplicity 1
Table 69 ethLinkId (Ethernet Link Identifier) (Cont.)
DN70577885 139
Flexi Transport Module Parameters ETHLK Parameters
Id:0900d80580975ffbConfidential
Description This parameter identifies the BTS transport Ethernet interface.
Format: "slot#-if#"
where
slot# = slot number of the unit containing the Ethernet interfaces, and
if# = the interface number of the physical interface on the unit
and
for FTIB/FTLB,
slot#: 1 : This is always 1, since there is only 1 slot.
if#: 1..3
for FTFB,
slot#: 1 : This is always 1, since there is only 1 slot.
if#: 1..4
Ports 1 and 2 are reserved for the external Gigabit Ethernet links. Ports 3 and 4 are reserved for the Ethernet links towards the FlexBus.
for Flexi BTS Release 3 Outdoor System Module (FSM),
slot#: 0 : This is always 0, since Transport is integrated into common system module.
if#: 1..2 : Value range is 1..2 for EIF1..EIF2 on this unit
Additionally, EIF2 can be configured as an RP3-01 port.
for Flexi BTS Release 3 Indoor System Module (FSI),
slot#: 0 : This is always 0, since Transport is integrated into common system module.
if#: 1..5 : Value range is 1..5 for EIF1..EIF5.
Usage of EIF1 and EIF3 is mutually exclusive. Similarly for EIF2 and EIF4. Additionally, EIF5 can be configured as an RP3-01 port.
for FTIF (optional outdoor external Transport module),
slot#: 1 : The slot number is '1', since this is an additional unit
if#: 1..4 : Value range is 1..4 for EIF1..EIF4 on this unit
Table 69 ethLinkId (Ethernet Link Identifier) (Cont.)
140 DN70577885
Flexi Transport Module Parameters
Id:0900d80580975ffbConfidential
ETHLK Parameters
Description (cont.) Usage of EIF1 and EIF3 is mutually exclusive. Similarly for EIF2 and EIF4. Usage of EIF1/EIF3 on this unit and EIF2 on FSM is mutually exclusive.
for FIIF (optional indoor external Transport module),
slot#: 1 : The slot number is '1', since this is an additional unit
if#: 1..2 : Value range is 1..2 for EIF1..EIF2 on this unit
Usage of EIF1 and EIF2 is mutually exclusive on this unit. Usage of EIF1/EIF2 on this unit and EIF5 on FSI unit is mutually exclusive.
Examples:
FTIB/FTLB:
1-1: refers to the physical Ethernet interface 1 in slot 1. (EIF1)
FTFB:
1-1: refers to the physical Gigabit Ethernet inter-face 1 in slot 1. (EIF1)
FSI/FSM:
0-1: refers to the physical Ethernet interface 1 in slot 0. (EIF1)
FTIF/FIIF:
1-1: refers to the physical Ethernet interface 1 in slot 1. (EIF1)
Range 3
Units characters
Formula for getting internal value
internal_value = gui_value
Default value -
Default value notes -
Related functions -
Modification Not modifiable
Related parameters -
Parameter relationships -
Related options -
Feature dependencies -
Interfaces • EM <-> FTM • RAC -> FTM • RAC <-> RACApp
Table 69 ethLinkId (Ethernet Link Identifier) (Cont.)
DN70577885 141
Flexi Transport Module Parameters ETHLK Parameters
Id:0900d80580975ffbConfidential
15.4 flushFdbOnLos (Flush fdb on LOS mode)
References -
Validation pattern -
Table 69 ethLinkId (Ethernet Link Identifier) (Cont.)
Parameter name Flush fdb on LOS mode
Abbreviated name flushFdbOnLos
3GPP name -
Managed Object ETHLK
Multiplicity 1
Description This parameter is available in WN7.0 2.0 release.
This parameter is true then dynamic MAC address entries of Forwarding Database (fdb) should be flushed when an Ethernet Layer Loss of Signal (LOS) is detected on one of its external switch-ports.
Range false (0), true (1)
Units -
Formula for getting internal value
• false => 0 • true => 1
Default value false (0)
Default value notes -
Related functions -
Modification On-Line
Related parameters -
Parameter relationships -
Related options -
Feature dependencies -
Interfaces • FTM <-> EM • FTM <-> RAC • RAC <-> RACApp
References -
Validation pattern -
Table 70 flushFdbOnLos (Flush fdb on LOS mode)
142 DN70577885
Flexi Transport Module Parameters
Id:0900d80580975ffbConfidential
ETHLK Parameters
15.5 l2BurstSize (Switch Port egress Shaper Burst Size)
Parameter name Switch Port egress Shaper Burst Size
Abbreviated name l2BurstSize
3GPP name -
Managed Object ETHLK
Multiplicity 1
Description This parameter specifies the maximum burst size that can be transmitted in a single burst in egress direction on this Ethernet interface of layer 2 switch.
The parameter value expresses a proportion of 0.1% of the related shaperrate per step.
The burst size is actually calculated by < l2ShaperRate x l2BurstSize x 1sec >.
Example: l2ShaperRate =100 [ 1 Mbit/s] and l2BurstSize=10 [ 0.1 %] results in a burst size of 100 Mbit/s x 10 x 0.1 x 1/100 x 1s = 1 Mbit = 125 Kbyte..
This parameter is valid only for FTLB.
Range 0... 60
Units -
Formula for getting internal value
internal_value = gui_value
Default value 0
Default value notes By default no bursts are allowed.
Related functions -
Modification On-Line
Related parameters -
Parameter relationships -
Related options • RAN1769 Ethernet Switching
Feature dependencies -
Interfaces • EM <-> FTM • RAC <-> FTM • RAC <-> RACApp
References -
Validation pattern -
Table 71 l2BurstSize (Switch Port egress Shaper Burst Size)
DN70577885 143
Flexi Transport Module Parameters ETHLK Parameters
Id:0900d80580975ffbConfidential
15.6 l2IngressRate (Switch Port ingress RateLimiter Rate )
Parameter name Switch Port ingress RateLimiter Rate
Abbreviated name l2IngressRate
3GPP name -
Managed Object ETHLK
Multiplicity 1
Description This parameter specifies the rate for limiting ingress traffic at the ethernet link interface when it partici-pates in the QOS aware layer 2 switch. Parameter value unit = MBit/s.
Range RT_LINE_RATE (0), RT_1 (1), RT_2 (2), RT_3 (3), RT_4 (4), RT_5 (5), RT_6 (6), RT_7 (7), RT_8 (8), RT_9 (9), RT_10 (10), RT_11 (11), RT_12 (12), RT_13 (13), RT_15 (15), RT_16 (16), RT_17 (17), RT_18 (18), RT_20 (20), RT_22 (22), RT_23 (23), RT_24 (24), RT_25 (25), RT_26 (26), RT_28 (28), RT_29 (29), RT_30 (30), RT_32 (32), RT_35 (35), RT_36 (36), RT_40 (40), RT_41 (41), RT_42 (42), RT_45 (45), RT_48 (48), RT_50 (50), RT_55 (55), RT_58 (58), RT_60 (60), RT_63 (63), RT_65 (65), RT_70 (70), RT_72 (72), RT_75 (75), RT_80 (80), RT_84 (84), RT_85 (85), RT_90 (90), RT_95 (95), RT_96 (96), RT_100 (100), RT_125 (125), RT_143 (143), RT_150 (150), RT_200 (200), RT_250 (250), RT_256 (256), RT_286 (286), RT_300 (300), RT_350 (350), RT_400 (400), RT_450 (450), RT_500 (500), RT_550 (550), RT_600 (600), RT_650 (650), RT_700 (700), RT_750 (750), RT_800 (800), RT_850 (850), RT_900 (900), RT_950 (950), RT_1000 (1000)
Units -
Table 72 l2IngressRate (Switch Port ingress RateLimiter Rate )
144 DN70577885
Flexi Transport Module Parameters
Id:0900d80580975ffbConfidential
ETHLK Parameters
Formula for getting internal value
gui ==> internal
RT_LINE_RATE ==> 0
RT_1 ==> 1
RT_2 ==> 2
RT_3 ==> 3
RT_4 ==> 4
RT_5 ==> 5
RT_6 ==> 6
RT_7 ==> 7
RT_8 ==> 8
RT_9 ==> 9
RT_10 ==> 10
RT_11 ==> 11
RT_12 ==> 12
RT_13 ==> 13
RT_15 ==> 15
RT_16 ==> 16
RT_17 ==> 17
RT_18 ==> 18
RT_20 ==> 20
RT_22 ==> 22
RT_23 ==> 23
RT_24 ==> 24
RT_25 ==> 25
RT_26 ==> 26
RT_28 ==> 28
RT_29 ==> 29
RT_30 ==> 30
RT_32 ==> 32
RT_35 ==> 35
RT_36 ==> 36
RT_40 ==> 40
RT_41 ==> 41
RT_42 ==> 42
RT_45 ==> 45
RT_48 ==> 48
RT_50 ==> 50
Table 72 l2IngressRate (Switch Port ingress RateLimiter Rate ) (Cont.)
DN70577885 145
Flexi Transport Module Parameters ETHLK Parameters
Id:0900d80580975ffbConfidential
Formula for getting internal value (cont.)
RT_55 ==> 55
RT_58 ==> 58
RT_60 ==> 60
RT_63 ==> 63
RT_65 ==> 65
RT_70 ==> 70
RT_72 ==> 72
RT_75 ==> 75
RT_80 ==> 80
RT_84 ==> 84
RT_85 ==> 85
RT_90 ==> 90
RT_95 ==> 95
RT_96 ==> 96
RT_100 ==> 100
RT_125 ==> 125
RT_143 ==> 143
RT_150 ==> 150
RT_200 ==> 200
RT_250 ==> 250
RT_256 ==> 256
RT_286 ==> 286
RT_300 ==> 300
RT_350 ==> 350
RT_400 ==> 400
RT_450 ==> 450
RT_500 ==> 500
RT_550 ==> 550
RT_600 ==> 600
RT_650 ==> 650
RT_700 ==> 700
RT_750 ==> 750
RT_800 ==> 800
RT_850 ==> 850
RT_900 ==> 900
RT_950 ==> 950
RT_1000 ==> 1000
Table 72 l2IngressRate (Switch Port ingress RateLimiter Rate ) (Cont.)
146 DN70577885
Flexi Transport Module Parameters
Id:0900d80580975ffbConfidential
ETHLK Parameters
15.7 l2ShaperRate (Switch Port egress Shaper Rate)
Default value RT_LINE_RATE (0)
Default value notes Use the configured line rate of the interface from the operator. This is defined in parameter ETHLK - speedAndDuplex. If the line rate is not configured forcibly by the operator, it is autodetected by the BTS.
Related functions -
Modification On-Line
Related parameters -
Parameter relationships -
Related options • RAN1769 Ethernet Switching
Feature dependencies -
Interfaces • EM <-> FTM • RAC <-> FTM • RAC <-> RACApp
References -
Validation pattern -
Table 72 l2IngressRate (Switch Port ingress RateLimiter Rate ) (Cont.)
Parameter name Switch Port egress Shaper Rate
Abbreviated name l2ShaperRate
3GPP name -
Managed Object ETHLK
Multiplicity 1
Description This parameter specifies the shaping rate of the ethernet link interface when participating in the QOS aware layer 2 switch.
The actual shaper rate is derived from the config-ured shaper rate by internal calculation.
Table 73 l2ShaperRate (Switch Port egress Shaper Rate)
DN70577885 147
Flexi Transport Module Parameters ETHLK Parameters
Id:0900d80580975ffbConfidential
Range RT_LINE_RATE (0), RT_1 (1), RT_2 (2), RT_3 (3), RT_4 (4), RT_5 (5), RT_6 (6), RT_7 (7), RT_8 (8), RT_9 (9), RT_10 (10), RT_11 (11), RT_12 (12), RT_13 (13), RT_15 (15), RT_16 (16), RT_17 (17), RT_18 (18), RT_20 (20), RT_22 (22), RT_23 (23), RT_24 (24), RT_25 (25), RT_26 (26), RT_28 (28), RT_29 (29), RT_30 (30), RT_32 (32), RT_35 (35), RT_36 (36), RT_40 (40), RT_41 (41), RT_42 (42), RT_45 (45), RT_48 (48), RT_50 (50), RT_55 (55), RT_58 (58), RT_60 (60), RT_63 (63), RT_65 (65), RT_70 (70), RT_72 (72), RT_75 (75), RT_80 (80), RT_84 (84), RT_85 (85), RT_90 (90), RT_95 (95), RT_96 (96), RT_100 (100), RT_125 (125), RT_143 (143), RT_150 (150), RT_200 (200), RT_250 (250), RT_256 (256), RT_286 (286), RT_300 (300), RT_350 (350), RT_400 (400), RT_450 (450), RT_500 (500), RT_550 (550), RT_600 (600), RT_650 (650), RT_700 (700), RT_750 (750), RT_800 (800), RT_850 (850), RT_900 (900), RT_950 (950), RT_1000 (1000)
Units -
Table 73 l2ShaperRate (Switch Port egress Shaper Rate) (Cont.)
148 DN70577885
Flexi Transport Module Parameters
Id:0900d80580975ffbConfidential
ETHLK Parameters
Formula for getting internal value
gui ==> internal
RT_LINE_RATE ==> 0
RT_1 ==> 1
RT_2 ==> 2
RT_3 ==> 3
RT_4 ==> 4
RT_5 ==> 5
RT_6 ==> 6
RT_7 ==> 7
RT_8 ==> 8
RT_9 ==> 9
RT_10 ==> 10
RT_11 ==> 11
RT_12 ==> 12
RT_13 ==> 13
RT_15 ==> 15
RT_16 ==> 16
RT_17 ==> 17
RT_18 ==> 18
RT_20 ==> 20
RT_22 ==> 22
RT_23 ==> 23
RT_24 ==> 24
RT_25 ==> 25
RT_26 ==> 26
RT_28 ==> 28
RT_29 ==> 29
RT_30 ==> 30
RT_32 ==> 32
RT_35 ==> 35
RT_36 ==> 36
RT_40 ==> 40
RT_41 ==> 41
RT_42 ==> 42
RT_45 ==> 45
RT_48 ==> 48
RT_50 ==> 50
Table 73 l2ShaperRate (Switch Port egress Shaper Rate) (Cont.)
DN70577885 149
Flexi Transport Module Parameters ETHLK Parameters
Id:0900d80580975ffbConfidential
Formula for getting internal value (cont.)
RT_55 ==> 55
RT_58 ==> 58
RT_60 ==> 60
RT_63 ==> 63
RT_65 ==> 65
RT_70 ==> 70
RT_72 ==> 72
RT_75 ==> 75
RT_80 ==> 80
RT_84 ==> 84
RT_85 ==> 85
RT_90 ==> 90
RT_95 ==> 95
RT_96 ==> 96
RT_100 ==> 100
RT_125 ==> 125
RT_143 ==> 143
RT_150 ==> 150
RT_200 ==> 200
RT_250 ==> 250
RT_256 ==> 256
RT_286 ==> 286
RT_300 ==> 300
RT_350 ==> 350
RT_400 ==> 400
RT_450 ==> 450
RT_500 ==> 500
RT_550 ==> 550
RT_600 ==> 600
RT_650 ==> 650
RT_700 ==> 700
RT_750 ==> 750
RT_800 ==> 800
RT_850 ==> 850
RT_900 ==> 900
RT_950 ==> 950
RT_1000 ==> 1000
Table 73 l2ShaperRate (Switch Port egress Shaper Rate) (Cont.)
150 DN70577885
Flexi Transport Module Parameters
Id:0900d80580975ffbConfidential
ETHLK Parameters
15.8 l2VlanIdList (Switch Port VLAN Member List)
Default value RT_LINE_RATE (0)
Default value notes Use the configured line rate of the interface from the operator. This is defined in parameter ETHLK - speedAndDuplex. If the line rate is not configured forcibly by the operator, it is autodetected by the BTS.
Related functions -
Modification On-Line
Related parameters -
Parameter relationships -
Related options • RAN1769 Ethernet Switching
Feature dependencies -
Interfaces • EM <-> FTM • RAC <-> FTM • RAC <-> RACApp
References -
Validation pattern -
Table 73 l2ShaperRate (Switch Port egress Shaper Rate) (Cont.)
Parameter name Switch Port VLAN Member List
Abbreviated name l2VlanIdList
3GPP name -
Managed Object ETHLK
Multiplicity 16
Description This parameter specifies the VLANs that are sup-ported over this ethernet interface when it partici-pates in the QOS aware layer 2 switch. The parameter is a list of up to 16 entries where each entry represents either a single VLAN identifier or a range of VLAN identifiers. The VLAN identifiers of the various entries should not but may overlap each other. The BTS internally will use a cleaned list on non-overlapping identifiers. The value of vlanIdList is however not changed by the BTS.
The default value of the parameter is the empty list.
Formula for getting internal value
-
Table 74 l2VlanIdList (Switch Port VLAN Member List)
DN70577885 151
Flexi Transport Module Parameters ETHLK Parameters
Id:0900d80580975ffbConfidential
15.9 highValue (Switch Port VLAN Member Range High Value)
Default value -
Default value notes -
Related functions -
Child parameters • highValue • lowValue
Modification On-Line
Related parameters -
Parameter relationships -
Related options • RAN1769 Ethernet Switching
Feature dependencies -
Interfaces • EM <-> FTM • RAC <-> FTM • RAC <-> RACApp
References -
Validation pattern -
Table 74 l2VlanIdList (Switch Port VLAN Member List) (Cont.)
Parameter name Switch Port VLAN Member Range High Value
Abbreviated name highValue
3GPP name -
Managed Object -
Multiplicity 1
Description This parameter specifies the upper value of a range of VLAN identifiers.
Range -1... 4094
Units -
Formula for getting internal value
internal_value = gui_value
Default value -1
Default value notes -
Related functions -
Modification On-Line
Related parameters -
Parameter relationships -
Table 75 highValue (Switch Port VLAN Member Range High Value)
152 DN70577885
Flexi Transport Module Parameters
Id:0900d80580975ffbConfidential
ETHLK Parameters
15.10 lowValue (Switch Port VLAN Member Range Low Value)
Related options • RAN1769 Ethernet Switching
Feature dependencies -
Interfaces • EM <-> FTM • RAC <-> FTM • RAC <-> RACApp
References -
Validation pattern -
Table 75 highValue (Switch Port VLAN Member Range High Value) (Cont.)
Parameter name Switch Port VLAN Member Range Low Value
Abbreviated name lowValue
3GPP name -
Managed Object -
Multiplicity 1
Description This parameter specifies either a single VLAN iden-tifier or the lower value of a range of VLAN identifi-ers.
Range 1... 4094
Units -
Formula for getting internal value
internal_value = gui_value
Default value -
Default value notes -
Related functions -
Modification On-Line
Related parameters -
Parameter relationships -
Related options • RAN1769 Ethernet Switching
Feature dependencies -
Interfaces • EM <-> FTM • RAC <-> FTM • RAC <-> RACApp
References -
Validation pattern -
Table 76 lowValue (Switch Port VLAN Member Range Low Value)
DN70577885 153
Flexi Transport Module Parameters ETHLK Parameters
Id:0900d80580975ffbConfidential
15.11 linkOAMEnabled (Link OAM enabling flag)
Parameter name Link OAM enabling flag
Abbreviated name linkOAMEnabled
3GPP name -
Managed Object ETHLK
Multiplicity 1
Description Enables the Link OAM functionality for this ethernet link. In consequence:
- the values of all statistics counters of the Link OAM feature for this interface are set to 0
- the Link OAM alarms for this interface are cleared
- the Link OAM discovery process is started, either in active or in passive mode.
linkOAMEnabled cannot be set to FB bit pipe inter-faces
NOTE:linkOAMEnabled flag cannot be value "true" in ATM Iub transport mode.
Range false (0), true (1)
Units -
Formula for getting internal value
• false => 0 • true => 1
Default value false (0)
Default value notes Link OAM is not enabled for the interface.
Related functions -
Modification On-Line
Related parameters iHSPAmode of IPNO - This parameter is not supported when iHSPAmode is set to enabled.
linkOAMProfile of ETHLK - The value of linkOAMEnabled shall only be set to true, if the value of linkOAMProfile is not the empty string but references an existing instance of object class OAMPRF.
Parameter relationships -
Related options -
Feature dependencies -
Table 77 linkOAMEnabled (Link OAM enabling flag)
154 DN70577885
Flexi Transport Module Parameters
Id:0900d80580975ffbConfidential
ETHLK Parameters
15.12 linkOAMProfile (Link OAM profile reference)
Interfaces • EM <-> FTM • RAC <-> FTM • RAC <-> RACApp
References -
Validation pattern -
Table 77 linkOAMEnabled (Link OAM enabling flag) (Cont.)
Parameter name Link OAM profile reference
Abbreviated name linkOAMProfile
3GPP name -
Managed Object ETHLK
Multiplicity 1
Description A reference to a Link OAM profile. This is a distin-guished name referencing an instance of class OAMPRF.
Range 0...40
Units characters
Formula for getting internal value
internal_value = gui_value
Default value -
Default value notes -
Related functions -
Modification On-Line
Related parameters iHSPAmode of IPNO - This parameter is not supported when iHSPAmode is set to enabled.
Parameter relationships -
Related options -
Feature dependencies -
Interfaces • EM <-> FTM • RAC <-> FTM • RAC <-> RACApp
References -
Validation pattern -
Table 78 linkOAMProfile (Link OAM profile reference)
DN70577885 155
Flexi Transport Module Parameters ETHLK Parameters
Id:0900d80580975ffbConfidential
15.13 macAddr (MAC address)
15.14 portDefaultPriority (Switch Port Default VLAN Priority)
Parameter name MAC address
Abbreviated name macAddr
3GPP name -
Managed Object ETHLK
Multiplicity 1
Description This parameter shows the MAC address of the ethernet interface.
Range 17
Units characters
Formula for getting internal value
internal_value = gui_value
Default value -
Default value notes -
Related functions -
Modification Not modifiable
Related parameters -
Parameter relationships -
Related options -
Feature dependencies -
Interfaces • FTM -> EM • FTM -> RAC
References -
Validation pattern -
Table 79 macAddr (MAC address)
Parameter name Switch Port Default VLAN Priority
Abbreviated name portDefaultPriority
3GPP name -
Managed Object ETHLK
Multiplicity 1
Table 80 portDefaultPriority (Switch Port Default VLAN Priority)
156 DN70577885
Flexi Transport Module Parameters
Id:0900d80580975ffbConfidential
ETHLK Parameters
15.15 portDefaultVlanId (Switch Port Default VLAN Identifier)
Description Default VLAN priority for untagged frames.
Every untagged ingress Ethernet frame at this inter-face gets assigned this Port Default Priority. If QoS classification mode is configured to VLAN-PCP, this priority is used for enqueing decision of the frame. If the frame egresses the switch tagged, this priority shall be used in the VLAN tag header.
Range 0... 7
Units -
Formula for getting internal value
internal_value = gui_value
Default value 0
Default value notes -
Related functions -
Modification On-Line
Related parameters enableLayer2Switching of L2SWI - VLAN aware switching mode should be enabled (enableLayer2Switching="true")
Parameter relationships -
Related options • RAN1769 Ethernet Switching
Feature dependencies -
Interfaces • EM <-> FTM • RAC <-> FTM • RAC <-> RACApp
References NSN reference: CN4420 QoS-VLAN Ethernet switching improvement
Validation pattern -
Table 80 portDefaultPriority (Switch Port Default VLAN Priority) (Cont.)
Parameter name Switch Port Default VLAN Identifier
Abbreviated name portDefaultVlanId
3GPP name -
Managed Object ETHLK
Multiplicity 1
Table 81 portDefaultVlanId (Switch Port Default VLAN Identifier)
DN70577885 157
Flexi Transport Module Parameters ETHLK Parameters
Id:0900d80580975ffbConfidential
15.16 speedAndDuplex (Speed and Duplex flag)
Description This parameter specifies the VLAN identifier that is inserted internally by the FTM into an untagged ingress frame that enters the layer 2 switch via this Ethernet interface - if parameter discardUntagged has value false for the Ethernet interface.
In order that the frame will be transmitted via the same or another Ethernet interface, after layer 2 switching has been performed, the same VLAN id must be configured in the VLAN identifier list of that Ethernet interface (see parameter l2VlanIdList). Else the frame will be discarded.
Default VLAN id cannot be configured as a part of interface's configured VLAN id list.
Range 1... 4094
Units -
Formula for getting internal value
internal_value = gui_value
Default value 1
Default value notes Default VLAN id = 1.
Related functions -
Modification On-Line
Related parameters enableLayer2Switching of L2SWI - VLAN aware switching mode should be enabled (enableLayer2Switching="true")
Parameter relationships -
Related options • RAN1769 Ethernet Switching
Feature dependencies -
Interfaces • EM <-> FTM • RAC <-> FTM • RAC <-> RACApp
References NSN reference: CN4420 QoS-VLAN Ethernet switching improvement
Validation pattern -
Table 81 portDefaultVlanId (Switch Port Default VLAN Identifier) (Cont.)
Parameter name Speed and Duplex flag
Abbreviated name speedAndDuplex
Table 82 speedAndDuplex (Speed and Duplex flag)
158 DN70577885
Flexi Transport Module Parameters
Id:0900d80580975ffbConfidential
ETHLK Parameters
3GPP name -
Managed Object ETHLK
Multiplicity 1
Description This parameter specificies if link characteristics are autonegotiated or not.
If not, the attribute contains the capacity and the duplex mode to be set forcibly. Note that 1000 MBit is available only on Gigabit Ethernet interfaces (GE).
This parameter is not applied for the FlexBus inter-faces of the FTFB hardware unit (interfaces 3 and 4 of the FTFB unit). For these interfaces the capacity and traffic mode is not configurable by the manage-ment system.
NOTE: With FSM-EIF2 / FSI-EIF5, AUTODETECT and Forced 1000Mbits are supported.
Range AUTODETECT (0), 1000MBIT_FULL (1), 100MBIT_FULL (2), 10MBIT_FULL (3)
Units -
Formula for getting internal value
gui ==> internal
AUTODETECT ==> 0
1000MBIT_FULL ==> 1
100MBIT_FULL ==> 2
10MBIT_FULL ==> 3
Default value AUTODETECT (0)
Default value notes -
Related functions -
Modification On-Line
Related parameters -
Parameter relationships -
Related options -
Feature dependencies -
Interfaces • EM <-> FTM • RAC <-> FTM • RAC <-> RACApp
References -
Validation pattern -
Table 82 speedAndDuplex (Speed and Duplex flag) (Cont.)
DN70577885 159
Flexi Transport Module Parameters ETHLK Parameters
Id:0900d80580975ffbConfidential
15.17 synchEMode (Synchronous ethernet mode)
Parameter name Synchronous ethernet mode
Abbreviated name synchEMode
3GPP name -
Managed Object ETHLK
Multiplicity 1
Description This parameter specifies if the FTM shall act as synchronous ethernet clock slave or master on this ethernet interface. The mode may also be autone-giotiated. An alarm shall be raised in case of a mode mismatch with the peer. The parameter is only relevant in case the synchronous ethernet regenerator function is switched on.
Range SEM_AUTO (0), SEM_SLAVE (1), SEM_MASTER (2)
Units -
Formula for getting internal value
gui ==> internal
SEM_AUTO ==> 0
SEM_SLAVE ==> 1
SEM_MASTER ==> 2
Default value SEM_AUTO (0)
Default value notes By default the mode is autonegotiated.
Related functions -
Modification On-Line
Related parameters synchERegenOn of STPG - Parameter synchEMode is only relevant in case parameter synchERegenOn has value true.
Parameter relationships -
Related options • RAN2071 Synchronous Ethernet Generation
Feature dependencies -
Interfaces • EM <-> FTM • RAC <-> FTM • RAC <-> RACApp
References -
Validation pattern -
Table 83 synchEMode (Synchronous ethernet mode)
160 DN70577885
Flexi Transport Module Parameters
Id:0900d80580975ffbConfidential
FRLI Parameters
16 FRLI Parameters
16.1 afrLinkInterfaceId (Fractional Interface Identifier)
Parameter name Fractional Interface Identifier
Abbreviated name afrLinkInterfaceId
3GPP name -
Managed Object FRLI
Multiplicity 1
Description This parameter identifies the fractional interface of a unit.
The object is identified by
- unit location (slot#)
- interface location (if#)
Format: slot#-if#
Ranges:
slot#: 1 (always)
if#:
FIIB, FILB, FTIB, FTIA, FTLB: 1..4
FTPB: 1..8
Fractional is only available on units FTPB, FTIA, FTIB and FTLB. Note that only 1 interface shall be used for fractional at any given time. FRLI is sup-ported only for JT1 capable unit when PDH IF type is JT1.
Range 3
Units characters
Formula for getting internal value
internal_value = gui_value
Default value -
Default value notes -
Related functions -
Modification Not modifiable
Related parameters -
Parameter relationships -
Related options -
Feature dependencies -
Table 84 afrLinkInterfaceId (Fractional Interface Identifier)
DN70577885 161
Flexi Transport Module Parameters FRLI Parameters
Id:0900d80580975ffbConfidential
16.2 afrTimeSlotSequence (ATM over Fractional JT1 Time Slot Sequence)
Interfaces • EM <-> FTM • RAC -> FTM • RAC <-> RACApp
References -
Validation pattern -
Table 84 afrLinkInterfaceId (Fractional Interface Identifier) (Cont.)
Parameter name ATM over Fractional JT1 Time Slot Sequence
Abbreviated name afrTimeSlotSequence
3GPP name -
Managed Object FRLI
Multiplicity 24
Description Specifies a list of consequtive timeslots that are to be used for an ATM interface, starting from timeslot 1. The maximum number of timeslots is 24.
At least two timeslots must be used.
Range TS1 (1), TS2 (2), TS3 (3), TS4 (4), TS5 (5), TS6 (6), TS7 (7), TS8 (8), TS9 (9), TS10 (10), TS11 (11), TS12 (12), TS13 (13), TS14 (14), TS15 (15), TS16 (16), TS17 (17), TS18 (18), TS19 (19), TS20 (20), TS21 (21), TS22 (22), TS23 (23), TS24 (24)
Units -
Table 85 afrTimeSlotSequence (ATM over Fractional JT1 Time Slot Sequence)
162 DN70577885
Flexi Transport Module Parameters
Id:0900d80580975ffbConfidential
FRLI Parameters
Formula for getting internal value
gui ==> internal
TS1 ==> 1
TS2 ==> 2
TS3 ==> 3
TS4 ==> 4
TS5 ==> 5
TS6 ==> 6
TS7 ==> 7
TS8 ==> 8
TS9 ==> 9
TS10 ==> 10
TS11 ==> 11
TS12 ==> 12
TS13 ==> 13
TS14 ==> 14
TS15 ==> 15
TS16 ==> 16
TS17 ==> 17
TS18 ==> 18
TS19 ==> 19
TS20 ==> 20
TS21 ==> 21
TS22 ==> 22
TS23 ==> 23
TS24 ==> 24
Default value -
Default value notes -
Related functions -
Modification On-Line
Related parameters pdhLineType of PPTT - JT1: EXTENDED_MULTIFRAME
Parameter relationships The "timeSlotSequence" must be set only if pdhLineType is set to EXTENDED_MULTIFRAME.
Related options -
Feature dependencies • RAN1649 ATM over Fractional JT1
Table 85 afrTimeSlotSequence (ATM over Fractional JT1 Time Slot Sequence)
DN70577885 163
Flexi Transport Module Parameters FRLI Parameters
Id:0900d80580975ffbConfidential
16.3 interfaceNumber (Interface Identifier)
Interfaces • EM <-> FTM • RAC <-> FTM • RAC <-> RACApp
References -
Validation pattern -
Table 85 afrTimeSlotSequence (ATM over Fractional JT1 Time Slot Sequence)
Parameter name Interface Identifier
Abbreviated name interfaceNumber
3GPP name -
Managed Object FRLI
Multiplicity 1
Description Defines the location of the PDH interface that is used for fractional mode. The value depends on the unit type.
FTIB, FTIA, FTLB: 1..4
FTPB: 1..8
Range 1... 8
Units -
Formula for getting internal value
internal_value = gui_value
Default value -
Default value notes -
Related functions -
Modification Not modifiable
Related parameters -
Parameter relationships -
Related options -
Feature dependencies • RAN1649 ATM over Fractional JT1
Interfaces • FTM -> EM • FTM -> RAC
References -
Validation pattern -
Table 86 interfaceNumber (Interface Identifier)
164 DN70577885
Flexi Transport Module Parameters
Id:0900d80580975ffbConfidential
FRLI Parameters
16.4 unitNumber (Unit Number)
Parameter name Unit Number
Abbreviated name unitNumber
3GPP name -
Managed Object FRLI
Multiplicity 1
Description This parameter identifies the slot number of the unit of the PDH interface that is used for fractional mode. The value is always 1 (only 1 slot available in this release).
Range 1... 1
Units -
Formula for getting internal value
internal_value = gui_value
Default value -
Default value notes -
Related functions -
Modification Not modifiable
Related parameters -
Parameter relationships -
Related options -
Feature dependencies • RAN1649 ATM over Fractional JT1
Interfaces • FTM -> EM • FTM -> RAC
References -
Validation pattern -
Table 87 unitNumber (Unit Number)
DN70577885 165
Flexi Transport Module Parameters FTM Parameters
Id:0900d80580975ffbConfidential
17 FTM Parameters
17.1 adaptationVersionMajor (Adaptation Version Major)
17.2 ftmId (BTS Transport Identifier)
Parameter name Adaptation Version Major
Abbreviated name adaptationVersionMajor
3GPP name -
Managed Object FTM
Multiplicity 1
Description Adaptation Version (Major) of the Site Configura-tion File supported by FTM.
Range 1...9
Units characters
Formula for getting internal value
internal_value = gui_value
Default value WN7.0 for WN7.0 1.0
WN7.0_2.0 for WN7.0 2.0
Default value notes -
Related functions -
Modification Not modifiable
Related parameters -
Parameter relationships -
Related options -
Feature dependencies -
Interfaces • EM <-> FTM • RAC <-> FTM • RAC <-> RACApp
References -
Validation pattern -
Table 88 adaptationVersionMajor (Adaptation Version Major)
Parameter name BTS Transport Identifier
Abbreviated name ftmId
3GPP name -
Table 89 ftmId (BTS Transport Identifier)
166 DN70577885
Flexi Transport Module Parameters
Id:0900d80580975ffbConfidential
FTM Parameters
17.3 locationName (Location Name)
Managed Object FTM
Multiplicity 1
Description This parameter identifies BTS transport.
The value is always 1.
Range 1... 1
Units -
Formula for getting internal value
internal_value = gui_value
Default value -
Default value notes -
Related functions -
Modification Not modifiable
Related parameters -
Parameter relationships -
Related options -
Feature dependencies -
Interfaces • EM <-> FTM • RAC -> FTM • RAC <-> RACApp
References -
Validation pattern -
Table 89 ftmId (BTS Transport Identifier) (Cont.)
Parameter name Location Name
Abbreviated name locationName
3GPP name -
Managed Object FTM
Multiplicity 1
Description Label that can be used to describe the geographical location of the network element.
Range 0...50
Units characters
Formula for getting internal value
internal_value = gui_value
Table 90 locationName (Location Name)
DN70577885 167
Flexi Transport Module Parameters FTM Parameters
Id:0900d80580975ffbConfidential
17.4 softwareReleaseVersion (Software Release Version)
Default value -
Default value notes -
Related functions -
Modification On-Line
Related parameters -
Parameter relationships -
Related options -
Feature dependencies -
Interfaces • EM <-> FTM • RAC <-> FTM • RAC <-> RACApp
References -
Validation pattern -
Table 90 locationName (Location Name) (Cont.)
Parameter name Software Release Version
Abbreviated name softwareReleaseVersion
3GPP name -
Managed Object FTM
Multiplicity 1
Description Identifies the SW Release Version of the Flexi-Transport Module. This value is set by the BTS.
Range 0...50
Units characters
Formula for getting internal value
internal_value = gui_value
Default value -
Default value notes -
Related functions -
Modification Not modifiable
Related parameters -
Parameter relationships -
Related options -
Feature dependencies -
Table 91 softwareReleaseVersion (Software Release Version)
168 DN70577885
Flexi Transport Module Parameters
Id:0900d80580975ffbConfidential
FTM Parameters
17.5 systemTitle (System Title)
Interfaces • FTM -> EM • FTM -> RAC
References -
Validation pattern -
Table 91 softwareReleaseVersion (Software Release Version) (Cont.)
Parameter name System Title
Abbreviated name systemTitle
3GPP name -
Managed Object FTM
Multiplicity 1
Description Label that can be used to enter the name of the network element.
Range 0...80
Units characters
Formula for getting internal value
internal_value = gui_value
Default value -
Default value notes -
Related functions -
Modification On-Line
Related parameters -
Parameter relationships -
Related options -
Feature dependencies -
Interfaces • EM <-> FTM • RAC <-> FTM • RAC <-> RACApp
References -
Validation pattern -
Table 92 systemTitle (System Title)
DN70577885 169
Flexi Transport Module Parameters FTM Parameters
Id:0900d80580975ffbConfidential
17.6 userLabel (User Label)
Parameter name User Label
Abbreviated name userLabel
3GPP name -
Managed Object FTM
Multiplicity 1
Description Label that can be used for a description of the BTS.
Range 0...128
Units characters
Formula for getting internal value
internal_value = gui_value
Default value -
Default value notes -
Related functions -
Modification On-Line
Related parameters -
Parameter relationships -
Related options -
Feature dependencies -
Interfaces • EM <-> FTM • RAC <-> FTM • RAC <-> RACApp
References -
Validation pattern -
Table 93 userLabel (User Label)
170 DN70577885
Flexi Transport Module Parameters
Id:0900d80580975ffbConfidential
IAIF Parameters
18 IAIF Parameters
18.1 VCI (Virtual Channel Identifier)
18.2 VPI (Virtual Path Identifier)
Parameter name Virtual Channel Identifier
Abbreviated name VCI
3GPP name -
Managed Object IAIF
Multiplicity 1
Description Virtual Channel Identifier.
Range 32... 4095
Units -
Formula for getting internal value
internal_value = gui_value
Default value -
Default value notes -
Related functions -
Modification Not modifiable
Related parameters -
Parameter relationships -
Related options -
Feature dependencies -
Interfaces • FTM -> EM • FTM -> RAC
References -
Validation pattern -
Table 94 VCI (Virtual Channel Identifier)
Parameter name Virtual Path Identifier
Abbreviated name VPI
3GPP name -
Managed Object IAIF
Multiplicity 1
Description Virtual Path Identifier.
Table 95 VPI (Virtual Path Identifier)
DN70577885 171
Flexi Transport Module Parameters IAIF Parameters
Id:0900d80580975ffbConfidential
18.3 atmIfNetId (ATM IP Net Interface Identifier)
Range 0... 255
Units -
Formula for getting internal value
internal_value = gui_value
Default value -
Default value notes -
Related functions -
Modification Not modifiable
Related parameters -
Parameter relationships -
Related options -
Feature dependencies -
Interfaces • FTM -> EM • FTM -> RAC
References -
Validation pattern -
Table 95 VPI (Virtual Path Identifier) (Cont.)
Parameter name ATM IP Net Interface Identifier
Abbreviated name atmIfNetId
3GPP name -
Managed Object IAIF
Multiplicity 1
Table 96 atmIfNetId (ATM IP Net Interface Identifier)
172 DN70577885
Flexi Transport Module Parameters
Id:0900d80580975ffbConfidential
IAIF Parameters
Description Identifies an ATM interface over an Ethernet Pseudowire.
The object is identified by
- Unit number (unit#)
- Interface number(if#, imag# or pw#)
- Virtual Path Identifier (vpi#)
- Virtual Channel Identifier (vci#)
Format:
- unit#-if#-vpi#vci# (e.g. 2-8-000C0)
- unit#-imag#-vpi#vci# (e.g. 2-34-0020)
Range:
unit#: 1
if#: 1..16 (maxi. 2 digits)
imag#: 33..75 (2 digits)
pw#: 76
vpi#: 00..FF (hexadecimal number, 2 digits)
vci#: 00..FFF (hexadecimal number, 3 digits)
Range 9...10
Units characters
Formula for getting internal value
internal_value = gui_value
Default value -
Default value notes -
Related functions -
Modification Not modifiable
Related parameters VCI of IAIF - The value of parameter VCI is contained in the value of parame-ter atmIfNetId.
VPI of IAIF - The value of parameter VPI is contained in the value of parame-ter atmIfNetId.
interfaceNumber of IAIF - The value of parameter interfaceNumber is contained in the value of parameter atmIfNetId.
unitNumber of IAIF - The value of parameter unitNumber is contained in the value of parameter atmIfNetId.
Parameter relationships -
Related options -
Table 96 atmIfNetId (ATM IP Net Interface Identifier) (Cont.)
DN70577885 173
Flexi Transport Module Parameters IAIF Parameters
Id:0900d80580975ffbConfidential
18.4 destIpAddr (Destination IP Address)
Feature dependencies -
Interfaces • EM <-> FTM • RAC -> FTM • RAC <-> RACApp
References -
Validation pattern -
Table 96 atmIfNetId (ATM IP Net Interface Identifier) (Cont.)
Parameter name Destination IP Address
Abbreviated name destIpAddr
3GPP name -
Managed Object IAIF
Multiplicity 1
Description Specifies the far-end IP address of an ATM point-to-point connection (IPoA).
Range 7...15
Units characters
Formula for getting internal value
internal_value = gui_value
Default value -
Default value notes -
Related functions -
Modification On-Line
Related parameters ftmIpAddr of IPNO
Parameter relationships The ftmIpAddr must be configured first.
Related options -
Feature dependencies -
Interfaces • EM <-> FTM • RAC <-> FTM • RAC <-> RACApp
References -
Validation pattern -
Table 97 destIpAddr (Destination IP Address)
174 DN70577885
Flexi Transport Module Parameters
Id:0900d80580975ffbConfidential
IAIF Parameters
18.5 interfaceNumber (Interface Number)
Parameter name Interface Number
Abbreviated name interfaceNumber
3GPP name -
Managed Object IAIF
Multiplicity 1
Description Defines the location on the unit of the physical inter-face that carries the signallink link.
The value depends on the unit type.
FTEB, FTPB, FTIF, FIIF: 1..8
FTIA, FIIB, FTIB, FTJA, FILB, FTLB: 1..4
FTFA, FTHA: 1..16
For IMA, the parameter identifies the IMA group. Values are: 33..75.
For the ATM over Ethernet pseudowire the value is always: 76.
Range 1... 76
Units -
Formula for getting internal value
internal_value = gui_value
Default value -
Default value notes -
Related functions -
Modification Not modifiable
Related parameters -
Parameter relationships -
Related options -
Feature dependencies -
Interfaces • FTM -> EM • FTM -> RAC
References -
Validation pattern -
Table 98 interfaceNumber (Interface Number)
DN70577885 175
Flexi Transport Module Parameters IAIF Parameters
Id:0900d80580975ffbConfidential
18.6 unitNumber (Unit Number)
Parameter name Unit Number
Abbreviated name unitNumber
3GPP name -
Managed Object IAIF
Multiplicity 1
Description Specifies the location of the unit (slot number). In this release it is always 1. The BTS has only 1 unit in slot 1.
Range 1... 1
Units -
Formula for getting internal value
internal_value = gui_value
Default value -
Default value notes -
Related functions -
Modification Not modifiable
Related parameters -
Parameter relationships -
Related options -
Feature dependencies -
Interfaces • FTM -> EM • FTM -> RAC
References -
Validation pattern -
Table 99 unitNumber (Unit Number)
176 DN70577885
Flexi Transport Module Parameters
Id:0900d80580975ffbConfidential
IEIF Parameters
19 IEIF Parameters
19.1 cir (Committed information rate)
Parameter name Committed information rate
Abbreviated name cir
3GPP name -
Managed Object IEIF
Multiplicity 1
Description The Committed Information Rate ("CIR") shall define the average rate up to which traffic is deliv-ered by the plain Ethernet interface. It shall define the guaranteed transport capacity for the interface. The parameter is required for dynamic CAC.
The sum of CIR values of all configured IP inter-faces (IEIF / IVIF) and CIR of Ethernet Service OAM multiplied by 1.2 cannot exceed the available Transport Ethernet interface bandwidth (see IEIF/shapedBandwidth and IEIF/sirTotal ) - Cir of Service OAM is taken in count if there exists at least one OAMMEP in the system.
If there are several IP interfaces and shaping is PATH, Connection Admission Control is based on CIR parameter of the IP interface that user plane uses.
Range 0... 1000000
Units kbps
Formula for getting internal value
internal_value = gui_value
Default value -
Default value notes -
Related functions -
Modification On-Line
Table 100 cir (Committed information rate)
DN70577885 177
Flexi Transport Module Parameters IEIF Parameters
Id:0900d80580975ffbConfidential
19.2 confCost (OSPF configured interface cost)
Related parameters shapedBandwidth of IEIF - The sum of CIR values of all configured IP interfaces (IEIF / IVIF) and CIR of Ethernet Service OAM mul-tiplied by 1.2 cannot exceed the available Transport Ethernet interface bandwidth (see IEIF/shaped-Bandwidth and IEIF/sirTotal ) - Cir of Service OAM is taken in count if there exists at least one OAMMEP in the system.
transportMode of IPNO - The parameter cir is only relevant in transport modes Dual Iub and IubIP.
localIpAddr of IEIF - The parameter cir is only relevant in case the interface is in use, i.e. in case the localIpAddr is different from 0.0.0.0.
sirTotal of IEIF - The sum of CIR values of all configured IP interfaces (IEIF / IVIF) and CIR of Ethernet Service OAM multiplied by 1.2 cannot exceed the available Transport Ethernet interface bandwidth (see IEIF/shapedBandwidth and IEIF/sirTotal ) - Cir of Service OAM is taken in count if there exists at least one OAMMEP in the system.
Parameter relationships -
Related options • RAN1709 VLAN Traffic Differentiation
Feature dependencies -
Interfaces • EM <-> FTM • RAC <-> FTM • RAC <-> RACApp
References -
Validation pattern -
Table 100 cir (Committed information rate) (Cont.)
Parameter name OSPF configured interface cost
Abbreviated name confCost
3GPP name -
Managed Object IEIF
Multiplicity 1
Table 101 confCost (OSPF configured interface cost)
178 DN70577885
Flexi Transport Module Parameters
Id:0900d80580975ffbConfidential
IEIF Parameters
19.3 helloInterval (OSPF keepalive message transmission interval)
Description This parameter specifies the cost used by the inter-face as defined by the operator. Value 0 means "not specified": If OSPF is enabled the cost calculated by the OSPF router shall be used instead.
Range 0... 65535
Units -
Formula for getting internal value
internal_value = gui_value
Default value 0
Default value notes Default means: "not specified by the operator, use OSPF router calculated cost instead".
Related functions -
Modification On-Line
Related parameters -
Parameter relationships -
Related options • RAN1879 Dynamic routing by OSPF
Feature dependencies -
Interfaces • EM <-> FTM • RAC <-> FTM • RAC <-> RACApp
References -
Validation pattern -
Table 101 confCost (OSPF configured interface cost) (Cont.)
Parameter name OSPF keepalive message transmission interval
Abbreviated name helloInterval
3GPP name -
Managed Object IEIF
Multiplicity 1
Description This parameter specifies the interval for transmit-ting keepalive ("Hello") messages.
Range 1... 65535
Units -
Table 102 helloInterval (OSPF keepalive message transmission interval)
DN70577885 179
Flexi Transport Module Parameters IEIF Parameters
Id:0900d80580975ffbConfidential
19.4 ieifId (Identifier of the plain Ethernet interface)
Formula for getting internal value
internal_value = gui_value
Default value 1
Default value notes -
Related functions -
Modification On-Line
Related parameters routerDeadInterval of IEIF - Router dead interval should be greater than hello interval
Parameter relationships -
Related options -
Feature dependencies -
Interfaces • EM <-> FTM • RAC <-> FTM • RAC <-> RACApp
References -
Validation pattern -
Table 102 helloInterval (OSPF keepalive message transmission interval) (Cont.)
Parameter name Identifier of the plain Ethernet interface
Abbreviated name ieifId
3GPP name -
Managed Object IEIF
Multiplicity 1
Description This parameter identifies the unique plain ethernet interface object in the BTS. Value is always 1. "FIIB, FILB, FTIA, FTIB, FTJA, FTLB" are supported for IEIF-1. "FTFB, FTIF and FIIF" are supported for IEIF-1 only in IubIP and DualIub mode. "FSM and FSI" are supported for IEIF-1 in IubIP mode.
Range 1
Units characters
Formula for getting internal value
internal_value = gui_value
Default value 1
Default value notes Always 1.
Table 103 ieifId (Identifier of the plain Ethernet interface)
180 DN70577885
Flexi Transport Module Parameters
Id:0900d80580975ffbConfidential
IEIF Parameters
19.5 interfaceArea (OSPF interface area)
Related functions -
Modification Not modifiable
Related parameters -
Parameter relationships -
Related options -
Feature dependencies -
Interfaces • EM <-> FTM • RAC -> FTM • RAC <-> RACApp
References -
Validation pattern -
Table 103 ieifId (Identifier of the plain Ethernet interface) (Cont.)
Parameter name OSPF interface area
Abbreviated name interfaceArea
3GPP name -
Managed Object IEIF
Multiplicity 1
Description This parameter specifies the OSPF area to which the interface belongs.
Range 0...15
Units characters
Formula for getting internal value
internal_value = gui_value
Default value -
Default value notes Empty value means, OSPF is disabled on this inter-face.
Related functions -
Modification On-Line
Related parameters -
Parameter relationships -
Related options • RAN1879 Dynamic routing by OSPF
Feature dependencies -
Table 104 interfaceArea (OSPF interface area)
DN70577885 181
Flexi Transport Module Parameters IEIF Parameters
Id:0900d80580975ffbConfidential
19.6 ipAddr (IP Address Info in the Transport Network)
Interfaces • EM <-> FTM • RAC <-> FTM • RAC <-> RACApp
References -
Validation pattern -
Table 104 interfaceArea (OSPF interface area) (Cont.)
Parameter name IP Address Info in the Transport Network
Abbreviated name ipAddr
3GPP name -
Managed Object IEIF
Multiplicity 1
Description Primary and - optionally - secondary IP address of the BTS in the transport network. Both are accom-panied with a subnet mask.
In this release only the primary IP address shall be used.
Formula for getting internal value
-
Default value -
Default value notes -
Related functions -
Child parameters • localIpAddr • netmask
Modification On-Line
Related parameters -
Parameter relationships -
Related options -
Feature dependencies -
Interfaces • EM <-> FTM • RAC <-> FTM • RAC <-> RACApp
References -
Validation pattern -
Table 105 ipAddr (IP Address Info in the Transport Network)
182 DN70577885
Flexi Transport Module Parameters
Id:0900d80580975ffbConfidential
IEIF Parameters
19.7 localIpAddr (Local Address of the IP Interface)
19.8 netmask (IP Network Mask)
Parameter name Local Address of the IP Interface
Abbreviated name localIpAddr
3GPP name -
Managed Object -
Multiplicity 1
Description IP address of the BTS in the transport network. It is accompanied with a subnet mask.
Range 7...15
Units characters
Formula for getting internal value
internal_value = gui_value
Default value -
Default value notes -
Related functions -
Modification On-Line
Related parameters -
Parameter relationships -
Related options -
Feature dependencies -
Interfaces • EM <-> FTM • RAC <-> FTM • RAC <-> RACApp
References -
Validation pattern -
Table 106 localIpAddr (Local Address of the IP Interface)
Parameter name IP Network Mask
Abbreviated name netmask
3GPP name -
Managed Object -
Multiplicity 1
Table 107 netmask (IP Network Mask)
DN70577885 183
Flexi Transport Module Parameters IEIF Parameters
Id:0900d80580975ffbConfidential
19.9 mtu (Maximum transfer unit)
Description Network mask for the IP address of the BTS in the transport network. To be entered in dotted decimal format.
Range 7...15
Units characters
Formula for getting internal value
internal_value = gui_value
Default value -
Default value notes -
Related functions -
Modification On-Line
Related parameters -
Parameter relationships -
Related options -
Feature dependencies -
Interfaces • EM <-> FTM • RAC <-> FTM • RAC <-> RACApp
References -
Validation pattern -
Table 107 netmask (IP Network Mask) (Cont.)
Parameter name Maximum transfer unit
Abbreviated name mtu
3GPP name -
Managed Object IEIF
Multiplicity 1
Description This is the maximum transfer unit in octets. In this release it has fixed value 1500.
Range 1500... 1500
Units octets
Formula for getting internal value
internal_value = gui_value
Default value 1500
Default value notes Fixed value 1500.
Table 108 mtu (Maximum transfer unit)
184 DN70577885
Flexi Transport Module Parameters
Id:0900d80580975ffbConfidential
IEIF Parameters
19.10 mtuMismatchDetection (MTU mismatch detection in use)
Related functions -
Modification Not modifiable
Related parameters -
Parameter relationships -
Related options • RAN74 Native Iub IP for Flexi WCDMA BTS • RAN1449 Dual Iub for Flexi WCDMA
Feature dependencies -
Interfaces • FTM -> EM • FTM -> RAC
References -
Validation pattern -
Table 108 mtu (Maximum transfer unit) (Cont.)
Parameter name MTU mismatch detection in use
Abbreviated name mtuMismatchDetection
3GPP name -
Managed Object IEIF
Multiplicity 1
Description If set to true, this parameter enables OSPF MTU mismatch detection on receiving DBD (Data Base Descriptor) packets on this interface.
Range false (0), true (1)
Units -
Formula for getting internal value
• false => 0 • true => 1
Default value true (1)
Default value notes -
Related functions -
Modification On-Line
Related parameters -
Parameter relationships -
Related options • RAN1879 Dynamic routing by OSPF
Feature dependencies -
Table 109 mtuMismatchDetection (MTU mismatch detection in use)
DN70577885 185
Flexi Transport Module Parameters IEIF Parameters
Id:0900d80580975ffbConfidential
19.11 ospfWithBfd (OSPF uses additionally BFD)
Interfaces • EM <-> FTM • RAC <-> FTM • RAC <-> RACApp
References -
Validation pattern -
Table 109 mtuMismatchDetection (MTU mismatch detection in use) (Cont.)
Parameter name OSPF uses additionally BFD
Abbreviated name ospfWithBfd
3GPP name -
Managed Object IEIF
Multiplicity 1
Description If set to true the OSPF router shall use Bidirectional Forwarding Detection (BFD) for detecting link inter-ruptions on this interface. If set to false, the OSPF router only uses keepalive Hello messages.
Range false (0), true (1)
Units -
Formula for getting internal value
• false => 0 • true => 1
Default value false (0)
Default value notes The OSPF router does not use BFD but only Hello messages.
Related functions -
Modification On-Line
Related parameters -
Parameter relationships -
Related options • RAN2359 OSPF enhancements
Feature dependencies -
Interfaces • EM <-> FTM • RAC <-> FTM • RAC <-> RACApp
References -
Validation pattern -
Table 110 ospfWithBfd (OSPF uses additionally BFD)
186 DN70577885
Flexi Transport Module Parameters
Id:0900d80580975ffbConfidential
IEIF Parameters
19.12 proxyArpIpAddrList (List of proxy ARP IP addresses for this interface.)
19.13 qosEnabled (QOS traffic priorisation enabling flag)
Parameter name List of proxy ARP IP addresses for this interface.
Abbreviated name proxyArpIpAddrList
3GPP name -
Managed Object IEIF
Multiplicity 16
Description This parameter holds a list of up to 16 IP addresses that can be used for proxy ARP detection.
The format of each IP address in the list is dotted decimal.
An empty list means the feature is not used.
Range 7...15
Units characters
Formula for getting internal value
internal_value = gui_value
Default value -
Default value notes -
Related functions -
Modification On-Line
Related parameters -
Parameter relationships -
Related options -
Feature dependencies • RAN2083 ProxyARP in BTS
Interfaces • EM <-> FTM • RAC <-> FTM • RAC <-> RACApp
References -
Validation pattern -
Table 111 proxyArpIpAddrList (List of proxy ARP IP addresses for this interface.)
Parameter name QOS traffic priorisation enabling flag
Abbreviated name qosEnabled
3GPP name -
Table 112 qosEnabled (QOS traffic priorisation enabling flag)
DN70577885 187
Flexi Transport Module Parameters IEIF Parameters
Id:0900d80580975ffbConfidential
Managed Object IEIF
Multiplicity 1
Description This parameter specifies if multiple queues are used over this interface or only a single one. Multiple queues allow DSCP based traffic priorisa-tion.
Amongst the active interfaces (IEIF or IVIF managed object instances) there shall be at least one and at most 2 interfaces carrying a multiple queue scheduler. So qosEnabled shall have value true for at least one active interface and must not have value true on more than 2 active interfaces.
Range false (0), true (1)
Units -
Formula for getting internal value
• false => 0 • true => 1
Default value true (1)
Default value notes By default a 6 PHB qeueue scheduler is indeed installed on the plain IP interface.
Related functions -
Modification On-Line
Related parameters localIpAddr of IEIF - Parameter qosEnabled is only relevant in case the interface is in use, i.e. in case the localIpAddr is different from 0.0.0.0.
iHSPAmode of IPNO - If iHS-PAmode is set to enabled then this value is set to 'true' internally.
Parameter relationships -
Related options -
Feature dependencies -
Interfaces • EM <-> FTM • RAC <-> FTM • RAC <-> RACApp
References -
Validation pattern -
Table 112 qosEnabled (QOS traffic priorisation enabling flag) (Cont.)
188 DN70577885
Flexi Transport Module Parameters
Id:0900d80580975ffbConfidential
IEIF Parameters
19.14 retransInterval (OSPF LSA retransmission interval)
19.15 routerDeadInterval (OSPF router read interval)
Parameter name OSPF LSA retransmission interval
Abbreviated name retransInterval
3GPP name -
Managed Object IEIF
Multiplicity 1
Description This parameter specifies the value for the retrans-mission of Link State Advertisement (LSA) messages for OSPF. Currently values of 1s and 2s are not supported for LSA retransmission interval .
This issue is to be resolved in the future release of the software.
Range 1... 65535
Units -
Formula for getting internal value
internal_value = gui_value
Default value 5
Default value notes -
Related functions -
Modification On-Line
Related parameters -
Parameter relationships -
Related options • RAN1879 Dynamic routing by OSPF
Feature dependencies -
Interfaces • EM <-> FTM • RAC <-> FTM • RAC <-> RACApp
References -
Validation pattern -
Table 113 retransInterval (OSPF LSA retransmission interval)
Parameter name OSPF router read interval
Abbreviated name routerDeadInterval
3GPP name -
Table 114 routerDeadInterval (OSPF router read interval)
DN70577885 189
Flexi Transport Module Parameters IEIF Parameters
Id:0900d80580975ffbConfidential
19.16 sbs (Shaper burst size)
Managed Object IEIF
Multiplicity 1
Description This parameter specifies the value for OSPF router dead interval in seconds. If no hello packet is received within the router dead interval, the link is assumed to be down.
Range 1... 65535
Units -
Formula for getting internal value
internal_value = gui_value
Default value 4
Default value notes -
Related functions -
Modification On-Line
Related parameters helloInterval of IEIF - Router dead interval should be greater than hello interval
Parameter relationships -
Related options • RAN1879 Dynamic routing by OSPF
Feature dependencies -
Interfaces • EM <-> FTM • RAC <-> FTM • RAC <-> RACApp
References -
Validation pattern -
Table 114 routerDeadInterval (OSPF router read interval) (Cont.)
Parameter name Shaper burst size
Abbreviated name sbs
3GPP name -
Managed Object IEIF
Multiplicity 1
Description This parameter holds the shaper burst size for the interface.
Range 1522... 2000000
Units -
Table 115 sbs (Shaper burst size)
190 DN70577885
Flexi Transport Module Parameters
Id:0900d80580975ffbConfidential
IEIF Parameters
19.17 sbsTotal (Total shaper burst size)
Formula for getting internal value
internal_value = gui_value
Default value 1522
Default value notes -
Related functions -
Modification On-Line
Related parameters localIpAddr of IEIF - Parameter sbs is only relevant in case the interface is in use, i.e. in case the localIpAddr is different from 0.0.0.0.
trafficPathShapingEnable of IEIF - Parameter sbs is only relevant in case parameter trafficPathShapingEnable has value TPS_PATH.
Parameter relationships -
Related options • RAN1709 VLAN Traffic Differentiation
Feature dependencies -
Interfaces • EM <-> FTM • RAC <-> FTM • RAC <-> RACApp
References -
Validation pattern -
Table 115 sbs (Shaper burst size) (Cont.)
Parameter name Total shaper burst size
Abbreviated name sbsTotal
3GPP name -
Managed Object IEIF
Multiplicity 1
Description The Total Shaper Burst Size ("SBS") defines the maximum burst size that is allowed to pass at the output of the WFQ aggregator.
Range 1522... 2000000
Units octets
Formula for getting internal value
internal_value = gui_value
Default value 1522
Default value notes -
Table 116 sbsTotal (Total shaper burst size)
DN70577885 191
Flexi Transport Module Parameters IEIF Parameters
Id:0900d80580975ffbConfidential
19.18 shapedBandwidth (Shaped Bandwidth)
Related functions -
Modification On-Line
Related parameters trafficPathShapingEnable of IEIF - Parameter sbsTotal is only relevant in case parameter trafficPathShapingEnable has value TPS_WFQ.
Parameter relationships -
Related options • RAN1709 VLAN Traffic Differentiation
Feature dependencies -
Interfaces • EM <-> FTM • RAC <-> FTM • RAC <-> RACApp
References -
Validation pattern -
Table 116 sbsTotal (Total shaper burst size) (Cont.)
Parameter name Shaped Bandwidth
Abbreviated name shapedBandwidth
3GPP name -
Managed Object IEIF
Multiplicity 1
Table 117 shapedBandwidth (Shaped Bandwidth)
192 DN70577885
Flexi Transport Module Parameters
Id:0900d80580975ffbConfidential
IEIF Parameters
Description This is the egress shaping bandwidth on the network interface (in kbit/s).
The related parameter upperLayingShaping decides if shaping is for the IP layer only or if the ethernet overhead is taken into account.
Values above 100 MBit/s are only allowed on Gigabit Ethernet interfaces.
Transport Ethernet interface bandwidth available for the traffic is defined by this param if shaping type (IEIF/trafficPathShapingEnable) is OFF or PATH. Bandwidth used by possibly configured CEoPSN reduces the available bandwidth. The sum of cir values of all configured IP interfaces (IEIF / IVIF) and cir of Ethernet Service OAM multiplied by 1.2 cannot exceed the available Transport Ethernet interface bandwidth. “cir” of Service OAM is taken in count if there exist at least one OAMMEP in the system.
Range 500... 1000000
Units kbit/s
Formula for getting internal value
internal_value = gui_value
Default value 100000
Default value notes The default is 1000000 (1 Gigabit/s) for Gigabit Ethernet interfaces.
Related functions -
Modification On-Line
Related parameters upperLayerShaping of IEIF
trafficPathShapingEnable of IEIF - Transport Ethernet interface bandwidth available for the traffic is defined by this param if shaping type (IEIF/trafficPathShapingEnable) is OFF or PATH.
Parameter relationships -
Related options -
Feature dependencies -
Interfaces • EM <-> FTM • RAC <-> FTM • RAC <-> RACApp
References -
Validation pattern -
Table 117 shapedBandwidth (Shaped Bandwidth) (Cont.)
DN70577885 193
Flexi Transport Module Parameters IEIF Parameters
Id:0900d80580975ffbConfidential
19.19 sir (Shaper information rate)
Parameter name Shaper information rate
Abbreviated name sir
3GPP name -
Managed Object IEIF
Multiplicity 1
Description This parameter holds the shaper information rate for the interface.
The maximum value of this parameter is 100 MBps for Fast Ethernet interfaces and 1 GBps for Gigabit Ethernet interfaces.
For FTLB, the actual minimum egress rate is 1.18 Mbps and on FSM-r3, the actual minimum egress rate is 1.56 Mbps due to technical limitations on Octeon.
Range 100... 1000000
Units -
Formula for getting internal value
internal_value = gui_value
Default value 1000000
Default value notes -
Related functions -
Modification On-Line
Related parameters localIpAddr of IEIF - Parameter sir is only relevant in case the interface is in use, i.e. in case the localIpAddr is different from 0.0.0.0.
trafficPathShapingEnable of IEIF - Parameter sir is only relevant in case parameter trafficPathShapingEnable has value TPS_PATH.
Parameter relationships -
Related options • RAN1709 VLAN Traffic Differentiation
Feature dependencies -
Interfaces • EM <-> FTM • RAC <-> FTM • RAC <-> RACApp
References -
Validation pattern -
Table 118 sir (Shaper information rate)
194 DN70577885
Flexi Transport Module Parameters
Id:0900d80580975ffbConfidential
IEIF Parameters
19.20 sirTotal (Total shaper information rate)
Parameter name Total shaper information rate
Abbreviated name sirTotal
3GPP name -
Managed Object IEIF
Multiplicity 1
Description This parameter holds the total Shaper Information Rate ("SIR") at the output of the WFQ aggregator.
The maximum value of this parameter is 100 MBps for Fast Ethernet interfaces and 1 GBps for Gigabit Ethernet interfaces.
Transport Ethernet interface bandwidth available for the traffic is defined by this param if shaping type (IEIF/trafficPathShapingEnable) is WFQ. Band-width used by possibly configured CEoPSN reduces the available bandwidth. The sum of cir values of all configured IP interfaces (IEIF / IVIF) and cir of Ethernet Service OAM multiplied by 1.2 cannot exceed the available Transport Ethernet interface bandwidth. “cir” of Service OAM is taken in count if there exists at least one OAMMEP in the system.
Range 100... 1000000
Units kbps
Formula for getting internal value
internal_value = gui_value
Default value 1000000
Default value notes -
Related functions -
Modification On-Line
Related parameters trafficPathShapingEnable of IEIF - Parameter sirTotal is only relevant in case param-eter trafficPathShapingEnable has value TPS_WFQ.
Parameter relationships -
Related options • RAN1709 VLAN Traffic Differentiation
Feature dependencies -
Interfaces • EM <-> FTM • RAC <-> FTM • RAC <-> RACApp
Table 119 sirTotal (Total shaper information rate)
DN70577885 195
Flexi Transport Module Parameters IEIF Parameters
Id:0900d80580975ffbConfidential
19.21 trafficPathShapingEnable (Traffic path shaping enabling flag)
References -
Validation pattern -
Table 119 sirTotal (Total shaper information rate) (Cont.)
Parameter name Traffic path shaping enabling flag
Abbreviated name trafficPathShapingEnable
3GPP name -
Managed Object IEIF
Multiplicity 1
Description This parameters decides on the type of shaping in case of VLANs. When traffic path shaping is enabled, shaping at the level of each VLAN enabled, else shaping at the WFQ aggregator level is enabled. Shaping may also be switched off entirely.
Transport Ethernet interface bandwidth available is dependent on this param (see IEIF/shapedBand-width and IEIF/sirTotal ).
Range TPS_OFF (0), TPS_WFQ (1), TPS_PATH (2)
Units -
Formula for getting internal value
gui ==> internal
TPS_OFF ==> 0
TPS_WFQ ==> 1
TPS_PATH ==> 2
Default value TPS_WFQ (1)
Default value notes -
Related functions -
Modification On-Line
Related parameters shapedBandwidth of IEIF - Transport Ethernet interface bandwidth available is dependent on this param (see IEIF/shapedBand-width and IEIF/sisTota;l).
sirTotal of IEIF - Transport Ethernet interface bandwidth available is depen-dent on this param (see IEIF/shapedBandwidth and IEIF/sisTotal).
Table 120 trafficPathShapingEnable (Traffic path shaping enabling flag)
196 DN70577885
Flexi Transport Module Parameters
Id:0900d80580975ffbConfidential
IEIF Parameters
19.22 transmitDelay (OSPF packet transmission delay)
Parameter relationships -
Related options • RAN1709 VLAN Traffic Differentiation
Feature dependencies -
Interfaces • EM <-> FTM • RAC <-> FTM • RAC <-> RACApp
References -
Validation pattern -
Table 120 trafficPathShapingEnable (Traffic path shaping enabling flag) (Cont.)
Parameter name OSPF packet transmission delay
Abbreviated name transmitDelay
3GPP name -
Managed Object IEIF
Multiplicity 1
Description This parameter specifies the OSPF transmit delay. This is the amount of time added to the age of an OSPF Link State Update (LSU) packet before transmitting it. It is the estimated number of seconds to transmit a packet over the interface.
Range 1... 65535
Units -
Formula for getting internal value
internal_value = gui_value
Default value 1
Default value notes -
Related functions -
Modification On-Line
Related parameters -
Parameter relationships -
Related options • RAN1879 Dynamic routing by OSPF
Feature dependencies -
Interfaces • EM <-> FTM • RAC <-> FTM • RAC <-> RACApp
Table 121 transmitDelay (OSPF packet transmission delay)
DN70577885 197
Flexi Transport Module Parameters IEIF Parameters
Id:0900d80580975ffbConfidential
19.23 upperLayerShaping (Upper Layer Shaping Enabled Flag)
References -
Validation pattern -
Table 121 transmitDelay (OSPF packet transmission delay) (Cont.)
Parameter name Upper Layer Shaping Enabled Flag
Abbreviated name upperLayerShaping
3GPP name -
Managed Object IEIF
Multiplicity 1
Description This parameter decides if shaping takes the ethernet overhead into account when shaping the bandwidth or not. If the flag has value true, the associated shapedBandwidth is the bandwidth on the IP layer only. If the flag has value false the Ethernet header is counted also. Use "true" for an IP only network, e.g. xDSL, use "false" for an Ethernet network, e.g. Metro Ethernet.
Range false (0), true (1)
Units -
Formula for getting internal value
• false => 0 • true => 1
Default value true
Default value notes By default the ethernet shaping should be disabled.
Related functions -
Modification On-Line
Related parameters -
Parameter relationships -
Related options -
Feature dependencies -
Interfaces • EM <-> FTM • RAC <-> FTM • RAC <-> RACApp
References -
Validation pattern -
Table 122 upperLayerShaping (Upper Layer Shaping Enabled Flag)
198 DN70577885
Flexi Transport Module Parameters
Id:0900d80580975ffbConfidential
IEIF Parameters
19.24 vlanEnabled (Vlan Enabled flag)
19.25 vlanId (Vlan ID)
Parameter name Vlan Enabled flag
Abbreviated name vlanEnabled
3GPP name -
Managed Object IEIF
Multiplicity 1
Description This flag indicates if Vlan mapping is enabled for this ethernet interface. Value "true" means that Vlan mapping is enabled. In case Vlan mapping is not enabled, all messages on the interface will be sent in plain format.
Range false (0), true (1)
Units -
Formula for getting internal value
• false => 0 • true => 1
Default value false (0)
Default value notes -
Related functions -
Modification On-Line
Related parameters -
Parameter relationships -
Related options -
Feature dependencies -
Interfaces • EM <-> FTM • RAC <-> FTM • RAC <-> RACApp
References -
Validation pattern -
Table 123 vlanEnabled (Vlan Enabled flag)
Parameter name Vlan ID
Abbreviated name vlanId
3GPP name -
Managed Object IEIF
Table 124 vlanId (Vlan ID)
DN70577885 199
Flexi Transport Module Parameters IEIF Parameters
Id:0900d80580975ffbConfidential
Multiplicity 1
Description Vlan ID to be used over this ethernet interface. The parameter is only relevant if vlan mapping is enabled (parameter Vlan Enabled flag has value true).
Range 0... 4094
Units -
Formula for getting internal value
internal_value = gui_value
Default value -
Default value notes -
Related functions -
Modification On-Line
Related parameters vlanEnabled of IEIF
Parameter relationships Parameter Vlan ID is only relevant if parameter Vlan Enabled flag has value true.
Related options -
Feature dependencies -
Interfaces • EM <-> FTM • RAC <-> FTM • RAC <-> RACApp
References -
Validation pattern -
Table 124 vlanId (Vlan ID) (Cont.)
200 DN70577885
Flexi Transport Module Parameters
Id:0900d80580975ffbConfidential
IHCP Parameters
20 IHCP Parameters
20.1 client_identifier (Entry set for DHCP clients identified by a system name)
20.2 dhcpClientIdentifier (DHCP Client Identifier)
Parameter name Entry set for DHCP clients identified by a system name
Abbreviated name client_identifier
3GPP name -
Managed Object IHCP
Multiplicity 10
Description This is a set of entries in the DHCP database in which an IP address is assigned to a DHCP client that identifies itself at the BTS by a system name (by a "text string").
Formula for getting internal value
-
Default value -
Default value notes -
Related functions -
Child parameters • dhcpClientIdentifier • dhcpFixedIpAddress
Modification On-Line
Related parameters -
Parameter relationships -
Related options -
Feature dependencies • DHCP Server
Interfaces • EM <-> FTM • RAC <-> FTM • RAC <-> RACApp
References -
Validation pattern -
Table 125 client_identifier (Entry set for DHCP clients identified by a system name)
Parameter name DHCP Client Identifier
Table 126 dhcpClientIdentifier (DHCP Client Identifier)
DN70577885 201
Flexi Transport Module Parameters IHCP Parameters
Id:0900d80580975ffbConfidential
20.3 dhcpFixedIpAddress (DHCP Fixed IP Address)
Abbreviated name dhcpClientIdentifier
3GPP name -
Managed Object -
Multiplicity 1
Description This is a unique string used in the DHCP server of the BTS for identifying a DHCP client that is assigned a fixed IP address.
This may either be one of the predefined names "RET1" (Remote Electrical Tilt), "RET2", "BBU" and "LMU" or a user-defined name consisting of up to 20 digits [0-9] and letters [a-z] and [A-Z].
Range 1...20
Units characters
Formula for getting internal value
internal_value = gui_value
Default value -
Default value notes -
Related functions -
Modification On-Line
Related parameters -
Parameter relationships -
Related options -
Feature dependencies • DHCP Server
Interfaces • EM <-> FTM • RAC <-> FTM • RAC <-> RACApp
References -
Validation pattern -
Table 126 dhcpClientIdentifier (DHCP Client Identifier) (Cont.)
Parameter name DHCP Fixed IP Address
Abbreviated name dhcpFixedIpAddress
3GPP name -
Managed Object -
Multiplicity 1
Table 127 dhcpFixedIpAddress (DHCP Fixed IP Address)
202 DN70577885
Flexi Transport Module Parameters
Id:0900d80580975ffbConfidential
IHCP Parameters
20.4 dhcpAccessId (DHCP Server Identifier)
Description Specifies a fixed IP address to be assigned to the DHCP client if it requests a lease with the specified client-identifier.
The IP address must be within the public IP subnet of the LMP. However, neither the IP addresses of the BTS nor its subnet IP address can be used.
Range 7...15
Units characters
Formula for getting internal value
internal_value = gui_value
Default value -
Default value notes -
Related functions -
Modification On-Line
Related parameters -
Parameter relationships -
Related options -
Feature dependencies • DHCP Server
Interfaces • EM <-> FTM • RAC <-> FTM • RAC <-> RACApp
References -
Validation pattern -
Table 127 dhcpFixedIpAddress (DHCP Fixed IP Address) (Cont.)
Parameter name DHCP Server Identifier
Abbreviated name dhcpAccessId
3GPP name -
Managed Object IHCP
Multiplicity 1
Description This parameter identifies the unique DHCP Server object in the BTS. Value is always 1.
Range 1... 1
Units -
Table 128 dhcpAccessId (DHCP Server Identifier)
DN70577885 203
Flexi Transport Module Parameters IHCP Parameters
Id:0900d80580975ffbConfidential
20.5 hardware_identifier (Entry set of DHCP clients identified by a MAC address)
Formula for getting internal value
internal_value = gui_value
Default value -
Default value notes -
Related functions -
Modification Not modifiable
Related parameters -
Parameter relationships -
Related options -
Feature dependencies -
Interfaces • EM <-> FTM • RAC -> FTM • RAC <-> RACApp
References -
Validation pattern -
Table 128 dhcpAccessId (DHCP Server Identifier) (Cont.)
Parameter name Entry set of DHCP clients identified by a MAC address
Abbreviated name hardware_identifier
3GPP name -
Managed Object IHCP
Multiplicity 10
Description This is set of entries in the DHCP database of the BTS that binds an IP address to a DHCP client that identifies itself at BTS by a hardware address (by a "MAC address").
Formula for getting internal value
-
Default value -
Default value notes -
Related functions -
Child parameters • dhcpFixedIpAddress • dhcpHardwareIdentifier
Table 129 hardware_identifier (Entry set of DHCP clients identified by a MAC address)
204 DN70577885
Flexi Transport Module Parameters
Id:0900d80580975ffbConfidential
IHCP Parameters
20.6 dhcpFixedIpAddress (DHCP Fixed IP Address)
Modification On-Line
Related parameters -
Parameter relationships -
Related options -
Feature dependencies • DHCP Server
Interfaces • EM <-> FTM • RAC <-> FTM • RAC <-> RACApp
References -
Validation pattern -
Table 129 hardware_identifier (Entry set of DHCP clients identified by a MAC address) (Cont.)
Parameter name DHCP Fixed IP Address
Abbreviated name dhcpFixedIpAddress
3GPP name -
Managed Object -
Multiplicity 1
Description Specifies the fixed IP address to be assigned to the DHCP client if it requests a lease with the hardware (MAC) address specified in parameter "DHCP Hardware Identifier".
The IP address must be within the public IP subnet of the LMP. However, the IP addresses of the BTS, its subnet IP address and its broadcast IP address cannot be used.
Range 7...15
Units characters
Formula for getting internal value
internal_value = gui_value
Default value -
Default value notes -
Related functions -
Modification On-Line
Related parameters -
Parameter relationships -
Table 130 dhcpFixedIpAddress (DHCP Fixed IP Address)
DN70577885 205
Flexi Transport Module Parameters IHCP Parameters
Id:0900d80580975ffbConfidential
20.7 dhcpHardwareIdentifier (DHCP Hardware Identifier)
Related options -
Feature dependencies • DHCP Server
Interfaces • EM <-> FTM • RAC <-> FTM • RAC <-> RACApp
References -
Validation pattern -
Table 130 dhcpFixedIpAddress (DHCP Fixed IP Address) (Cont.)
Parameter name DHCP Hardware Identifier
Abbreviated name dhcpHardwareIdentifier
3GPP name -
Managed Object -
Multiplicity 1
Description This is the unique hardware (MAC) address within the DHCP server of the BTS by which a DHCP client identifies itself at the BTS. The server will then assign the IP address of parameter "DHCP Fixed IP Address" to the client.
Range 17
Units characters
Formula for getting internal value
internal_value = gui_value
Default value -
Default value notes -
Related functions -
Modification On-Line
Related parameters -
Parameter relationships -
Related options -
Feature dependencies • DHCP Server
Interfaces • EM <-> FTM • RAC <-> FTM • RAC <-> RACApp
References -
Table 131 dhcpHardwareIdentifier (DHCP Hardware Identifier)
206 DN70577885
Flexi Transport Module Parameters
Id:0900d80580975ffbConfidential
IHCP Parameters
20.8 range_identifier (DHCP server IP address pool)
20.9 dhcpRangeEnd (DHCP Range End IP Address)
Validation pattern -
Table 131 dhcpHardwareIdentifier (DHCP Hardware Identifier) (Cont.)
Parameter name DHCP server IP address pool
Abbreviated name range_identifier
3GPP name -
Managed Object IHCP
Multiplicity 1
Description This entry reserves an IP address range to be used for assignments for the DHCP clients.
Formula for getting internal value
-
Default value -
Default value notes -
Related functions -
Child parameters • dhcpRangeEnd • dhcpRangeStart
Modification On-Line
Related parameters -
Parameter relationships -
Related options -
Feature dependencies • DHCP Server
Interfaces • EM <-> FTM • RAC <-> FTM • RAC <-> RACApp
References -
Validation pattern -
Table 132 range_identifier (DHCP server IP address pool)
Parameter name DHCP Range End IP Address
Abbreviated name dhcpRangeEnd
3GPP name -
Table 133 dhcpRangeEnd (DHCP Range End IP Address)
DN70577885 207
Flexi Transport Module Parameters IHCP Parameters
Id:0900d80580975ffbConfidential
20.10 dhcpRangeStart (DHCP Range Start IP Address)
Managed Object -
Multiplicity 1
Description Specifies the final IP address of the DHCP IP address range.
The IP address must be within the public IP subnet of the LMP.
However, neither the IP addresses of the BTS nor its subnet IP address shall be used.
Range 7...15
Units characters
Formula for getting internal value
internal_value = gui_value
Default value -
Default value notes -
Related functions -
Modification On-Line
Related parameters -
Parameter relationships -
Related options -
Feature dependencies • DHCP Server
Interfaces • EM <-> FTM • RAC <-> FTM • RAC <-> RACApp
References -
Validation pattern -
Table 133 dhcpRangeEnd (DHCP Range End IP Address) (Cont.)
Parameter name DHCP Range Start IP Address
Abbreviated name dhcpRangeStart
3GPP name -
Managed Object -
Multiplicity 1
Table 134 dhcpRangeStart (DHCP Range Start IP Address)
208 DN70577885
Flexi Transport Module Parameters
Id:0900d80580975ffbConfidential
IHCP Parameters
Description Specifies the starting IP address of the DHCP IP address range.
The IP address must be within the public IP subnet of the LMP.
However, neither the IP addresses of the BTS nor its subnet IP address shall be used.
Range 0...15
Units characters
Formula for getting internal value
internal_value = gui_value
Default value -
Default value notes -
Related functions -
Modification On-Line
Related parameters -
Parameter relationships -
Related options -
Feature dependencies • DHCP Server
Interfaces • EM <-> FTM • RAC <-> FTM • RAC <-> RACApp
References -
Validation pattern -
Table 134 dhcpRangeStart (DHCP Range Start IP Address) (Cont.)
DN70577885 209
Flexi Transport Module Parameters IMAG Parameters
Id:0900d80580975ffbConfidential
21 IMAG Parameters
21.1 administrativeState (Administrative State)
Parameter name Administrative State
Abbreviated name administrativeState
3GPP name -
Managed Object IMAG
Multiplicity 1
Description Used to lock and unlock the IMA group.
When the Adminstrative State is locked, the IMA group is deactivated. All alarms and any ATM cell transfer is suppressed. Unlocking the Administra-tive State will trigger the creation of a TCTT (ATM interface).
Note that setting the Administrative State to locked will not delete the associated TCTT.
Changing the value for an IMA group also changes the Administrative State of the physical interfaces assigned to the group.
Range locked (0), unlocked (1)
Units -
Formula for getting internal value
gui ==> internal
locked ==> 0
unlocked ==> 1
Default value locked (0)
Default value notes -
Related functions -
Modification On-Line
Related parameters -
Parameter relationships -
Related options -
Feature dependencies • Inverse Multiplexing (IMA)
Interfaces • EM <-> FTM • RAC <-> FTM • RAC <-> RACApp
References -
Table 135 administrativeState (Administrative State)
210 DN70577885
Flexi Transport Module Parameters
Id:0900d80580975ffbConfidential
IMAG Parameters
21.2 imaGroupId (IMA group identifier)
Validation pattern -
Table 135 administrativeState (Administrative State) (Cont.)
Parameter name IMA group identifier
Abbreviated name imaGroupId
3GPP name -
Managed Object IMAG
Multiplicity 1
Description This parameter identifies the IMA group.
Format: unit#-imag#
where
unit#: always 1 (unit number)
imag#: 33..75 (IMA group number on the unit)
Range 4
Units characters
Formula for getting internal value
internal_value = gui_value
Default value -
Default value notes -
Related functions -
Modification Not modifiable
Related parameters -
Parameter relationships -
Related options -
Feature dependencies -
Interfaces • EM <-> FTM • RAC -> FTM • RAC <-> RACApp
References -
Validation pattern -
Table 136 imaGroupId (IMA group identifier)
DN70577885 211
Flexi Transport Module Parameters IMAG Parameters
Id:0900d80580975ffbConfidential
21.3 imaVersionId (IMA Version Identifier)
Parameter name IMA Version Identifier
Abbreviated name imaVersionId
3GPP name -
Managed Object IMAG
Multiplicity 1
Description Specifies the standard according to which the IMA group is operating.
ATM Forum af-phy-0086.000 allows for two inter-pretations: IMA version 1.0 and IMA version 1.0Alt (alternate). ATM Forum af-phy-0086.001 elimi-nates this ambiguity and is the basis for IMA version 1.1. This version is the most common one.
The Transport Module provides also an option to atomatically detect the correct IMA version (default).
IMA version 1.0 is not supported
The value must be the same at both local and remote site.
Range imaVersion10Alt (1), imaVersion11 (2), automatic (3)
Units -
Formula for getting internal value
gui ==> internal
imaVersion10Alt ==> 1
imaVersion11 ==> 2
automatic ==> 3
Default value automatic (3)
Default value notes -
Related functions -
Modification On-Line
Related parameters -
Parameter relationships -
Related options -
Feature dependencies • Inverse Multiplexing (IMA)
Interfaces • EM <-> FTM • RAC <-> FTM • RAC <-> RACApp
References -
Table 137 imaVersionId (IMA Version Identifier)
212 DN70577885
Flexi Transport Module Parameters
Id:0900d80580975ffbConfidential
IMAG Parameters
21.4 interfaceNumber (Interface Number)
21.5 interfaces (Physical interface list)
Validation pattern -
Table 137 imaVersionId (IMA Version Identifier) (Cont.)
Parameter name Interface Number
Abbreviated name interfaceNumber
3GPP name -
Managed Object IMAG
Multiplicity 1
Description This parameter holds the IMA Group identifier.
Range 33... 75
Units -
Formula for getting internal value
internal_value = gui_value
Default value -
Default value notes -
Related functions -
Modification Not modifiable
Related parameters -
Parameter relationships -
Related options -
Feature dependencies • Inverse Multiplexing (IMA)
Interfaces • EM <-> FTM • RAC <-> FTM • RAC <-> RACApp
References -
Validation pattern -
Table 138 interfaceNumber (Interface Number)
Parameter name Physical interface list
Abbreviated name interfaces
3GPP name -
Managed Object IMAG
Table 139 interfaces (Physical interface list)
DN70577885 213
Flexi Transport Module Parameters IMAG Parameters
Id:0900d80580975ffbConfidential
21.6 minNumLinks (Minimum Number of Links)
Multiplicity 16
Description This parameter holds the list of the physical inter-faces used by the IMA group.
The maximum number of interfaces in one IMA group depends on the unit type:
FIIB, FILB, FTIA, FTIB, FTJA, FTLB: 1..4
FTEB, FTPB, FTFA, FTIF, FIIF: 1..8
FTFA, FTHA, FTFB: 1..16
Range 0... 16
Units -
Formula for getting internal value
internal_value = gui_value
Default value -
Default value notes -
Related functions -
Modification On-Line
Related parameters -
Parameter relationships -
Related options -
Feature dependencies -
Interfaces • EM <-> FTM • RAC <-> FTM • RAC <-> RACApp
References -
Validation pattern -
Table 139 interfaces (Physical interface list) (Cont.)
Parameter name Minimum Number of Links
Abbreviated name minNumLinks
3GPP name -
Managed Object IMAG
Multiplicity 1
Table 140 minNumLinks (Minimum Number of Links)
214 DN70577885
Flexi Transport Module Parameters
Id:0900d80580975ffbConfidential
IMAG Parameters
21.7 unitNumber (Unit Number)
Description Specifies the minimum number of IMA links required to keep the IMA group operable.
If the number of working IMA links is smaller, the IMA group is out of use.
Range 1... 16
Units -
Formula for getting internal value
internal_value = gui_value
Default value 1
Default value notes -
Related functions -
Modification On-Line
Related parameters -
Parameter relationships -
Related options -
Feature dependencies • Inverse Multiplexing (IMA)
Interfaces • EM <-> FTM • RAC <-> FTM • RAC <-> RACApp
References -
Validation pattern -
Table 140 minNumLinks (Minimum Number of Links) (Cont.)
Parameter name Unit Number
Abbreviated name unitNumber
3GPP name -
Managed Object IMAG
Multiplicity 1
Description Specifies the location of the unit (slot number). In this release it is always 1. The BTS has only 1 unit in slot 1.
Range 1... 1
Units -
Formula for getting internal value
internal_value = gui_value
Table 141 unitNumber (Unit Number)
DN70577885 215
Flexi Transport Module Parameters IMAG Parameters
Id:0900d80580975ffbConfidential
Default value -
Default value notes -
Related functions -
Modification Not modifiable
Related parameters -
Parameter relationships -
Related options -
Feature dependencies • Inverse Multiplexing (IMA)
Interfaces • EM <-> FTM • RAC <-> FTM • RAC <-> RACApp
References -
Validation pattern -
Table 141 unitNumber (Unit Number) (Cont.)
216 DN70577885
Flexi Transport Module Parameters
Id:0900d80580975ffbConfidential
INTP Parameters
22 INTP Parameters
22.1 ntpAccessId (NTP Identifier)
22.2 ntpServers (List of NTP Server IP Addresses)
Parameter name NTP Identifier
Abbreviated name ntpAccessId
3GPP name -
Managed Object INTP
Multiplicity 1
Description This parameter identifies the unique NTP configu-ration entity of the BTS. The value is always 1.
Range 1... 1
Units -
Formula for getting internal value
internal_value = gui_value
Default value -
Default value notes -
Related functions -
Modification Not modifiable
Related parameters -
Parameter relationships -
Related options -
Feature dependencies -
Interfaces • EM <-> FTM • RAC -> FTM • RAC <-> RACApp
References -
Validation pattern -
Table 142 ntpAccessId (NTP Identifier)
Parameter name List of NTP Server IP Addresses
Abbreviated name ntpServers
3GPP name -
Managed Object INTP
Table 143 ntpServers (List of NTP Server IP Addresses)
DN70577885 217
Flexi Transport Module Parameters INTP Parameters
Id:0900d80580975ffbConfidential
Multiplicity 3
Description Specifies the IP addresses of the NTP servers.
Range 7...15
Units characters
Formula for getting internal value
internal_value = gui_value
Default value -
Default value notes -
Related functions -
Modification On-Line
Related parameters -
Parameter relationships -
Related options -
Feature dependencies • NTP Server
Interfaces • EM <-> FTM • RAC <-> FTM • RAC <-> RACApp
References -
Validation pattern -
Table 143 ntpServers (List of NTP Server IP Addresses) (Cont.)
218 DN70577885
Flexi Transport Module Parameters
Id:0900d80580975ffbConfidential
IPNO Parameters
23 IPNO Parameters
23.1 bfdHoldUpTime (BFD throttle time for re-installing protec-tion routes)
Parameter name BFD throttle time for re-installing protection routes
Abbreviated name bfdHoldUpTime
3GPP name -
Managed Object IPNO
Multiplicity 1
Description This parameter specifies the delay for re-installig routes as active ones after a BFD session has recovered from down to up state. Defining a delay can prevent too heavy toggling of de-installing and re-installing routes for unstable BFD sessions.
Range 0... 900
Units seconds
Formula for getting internal value
internal_value = gui_value
Default value 0
Default value notes -
Related functions -
Modification On-Line
Related parameters iHSPAmode of IPNO - Not supported in case parameter iHSPAmode is set to enabled.
Parameter relationships -
Related options • RAN2440 Fast IP Rerouting
Feature dependencies -
Interfaces • EM <-> FTM • RAC <-> FTM • RAC <-> RACApp
References -
Validation pattern -
Table 144 bfdHoldUpTime (BFD throttle time for re-installing protection routes)
DN70577885 219
Flexi Transport Module Parameters IPNO Parameters
Id:0900d80580975ffbConfidential
23.2 btsId (BTS Identifier)
23.3 btsIpAddr (Base Station IP Address)
Parameter name BTS Identifier
Abbreviated name btsId
3GPP name -
Managed Object IPNO
Multiplicity 1
Description Base Station Identifier.
Reserved Values: 0 = "BTS not configured" and 0xFFFF (=65535) = "RNC not configured"
Range 1... 65534
Units -
Formula for getting internal value
internal_value = gui_value
Default value -
Default value notes -
Related functions -
Modification On-Line
Related parameters -
Parameter relationships -
Related options -
Feature dependencies -
Interfaces • EM <-> FTM • RAC <-> FTM • RAC <-> RACApp
References -
Validation pattern -
Table 145 btsId (BTS Identifier)
Parameter name Base Station IP Address
Abbreviated name btsIpAddr
3GPP name -
Managed Object IPNO
Multiplicity 1
Table 146 btsIpAddr (Base Station IP Address)
220 DN70577885
Flexi Transport Module Parameters
Id:0900d80580975ffbConfidential
IPNO Parameters
23.4 cPlaneIpAddress (Control-plane application IP address)
Description IP Address of the Base Station.
Address under which the Base Station is available remotely. FSMr3 is not configurable on this param-eter.
Range 7...15
Units characters
Formula for getting internal value
internal_value = gui_value
Default value -
Default value notes -
Related functions -
Modification On-Line
Related parameters -
Parameter relationships -
Related options -
Feature dependencies -
Interfaces • EM <-> FTM • RAC <-> FTM • RAC <-> RACApp
References -
Validation pattern -
Table 146 btsIpAddr (Base Station IP Address) (Cont.)
Parameter name Control-plane application IP address
Abbreviated name cPlaneIpAddress
3GPP name -
Managed Object IPNO
Multiplicity 1
Table 147 cPlaneIpAddress (Control-plane application IP address)
DN70577885 221
Flexi Transport Module Parameters IPNO Parameters
Id:0900d80580975ffbConfidential
Description This parameter specifies the IP address to be used for control-plane traffic by the FTM.
This IP address can collapse with the local IP address of the plain Ethernet interface (IEIF object) or with the local IP address of one of the VLAN interfaces (IVIF object) or with the local IP address of the ML-PPP interface (P3SL or P3ML object) of the FTM. If it does not collapse with such network interface IP address, the IP address is virtual.
The format of this parameter is dotted decimal.
Value 0.0.0.0 means the control-plane application IP address is not used.
The parameter is not used at all in case of AtmOv-erEthernet (AtmIub) and in case of Dual Iub mode.
Range 7...15
Units characters
Formula for getting internal value
internal_value = gui_value
Default value 0.0.0.0
Default value notes By default the control-plane application IP address is not used.
Related functions -
Modification On-Line
Related parameters transportMode of IPNO - Parameter cPlaneIpAddress is irrelevant in case parameter transportMode has value AtmOverEthernet and in case parameter transportMode has value DualIub.
Parameter relationships -
Related options -
Feature dependencies • CN4065
Interfaces • EM <-> FTM • RAC <-> FTM • RAC <-> RACApp
References -
Validation pattern -
Table 147 cPlaneIpAddress (Control-plane application IP address) (Cont.)
222 DN70577885
Flexi Transport Module Parameters
Id:0900d80580975ffbConfidential
IPNO Parameters
23.5 cesopsnIpAddress (CES over PSN application IP address)
Parameter name CES over PSN application IP address
Abbreviated name cesopsnIpAddress
3GPP name -
Managed Object IPNO
Multiplicity 1
Description This parameter specifies the application IP address for CES over PSN.
The address can collapse with the IP address of the plain Ethernet interface (IEIF object) or with the IP address of one of the VLAN interfaces (IVIF object). If it does not collapse with such network interface IP address, the CES over PSN IP address is virtual.
The format of this parameter is dotted decimal.
Value 0.0.0.0 means the CES over PSN IP address is not used.
The parameter is not used at all in case of AtmOv-erEthernet (AtmIub) and in DualIub mode.
Range 7...15
Units characters
Formula for getting internal value
internal_value = gui_value
Default value 0.0.0.0
Default value notes By default the CES over PSN application IP address is not used.
Related functions -
Modification On-Line
Related parameters transportMode of IPNO - Parameter cesopsnIpAddress is irrelevant in case parameter transportMode has value AtmOverEthernet and in case parameter transportMode has value DualIub.
iHSPAmode of IPNO - Not supported in case parameter iHSPAmode is set to enabled.
administrativeState of P3SL - Parameter cesopsnIpAddress is irrelevant in case parameter administrativeState has value unlocked.
administrativeState of P3ML - Parameter cesopsnIpAddress is irrelevant in case parameter administrativeState has value unlocked.
Table 148 cesopsnIpAddress (CES over PSN application IP address)
DN70577885 223
Flexi Transport Module Parameters IPNO Parameters
Id:0900d80580975ffbConfidential
23.6 disableFtp (Disable FTP server)
Parameter relationships -
Related options -
Feature dependencies • CN4065
Interfaces • EM <-> FTM • RAC <-> FTM • RAC <-> RACApp
References -
Validation pattern -
Table 148 cesopsnIpAddress (CES over PSN application IP address) (Cont.)
Parameter name Disable FTP server
Abbreviated name disableFtp
3GPP name -
Managed Object IPNO
Multiplicity 1
Description Control whether to allow/disallow running FTP server on Transport module for security reasons. FSMr3 HW units are not supported.
Range FTP_SERVER_ENABLED (0), FTP_SERVER_DISABLED (1)
Units -
Formula for getting internal value
gui ==> internal
FTP_SERVER_ENABLED ==> 0
FTP_SERVER_DISABLED ==> 1
Default value FTP_SERVER_ENABLED (0)
Default value notes -
Related functions -
Modification On-Line
Related parameters -
Parameter relationships -
Related options -
Feature dependencies -
Interfaces • EM <-> FTM • RAC <-> FTM • RAC <-> RACApp
Table 149 disableFtp (Disable FTP server)
224 DN70577885
Flexi Transport Module Parameters
Id:0900d80580975ffbConfidential
IPNO Parameters
23.7 flexBusIpAddr (Public IP Address of Flexbus Part of BTS)
23.8 fpLocalUdpPort (Local UDP port for small packets multi-plexing)
References -
Validation pattern -
Table 149 disableFtp (Disable FTP server) (Cont.)
Parameter name Public IP Address of Flexbus Part of BTS
Abbreviated name flexBusIpAddr
3GPP name -
Managed Object IPNO
Multiplicity 1
Description Public IP address of the Flexbus part of the unit. In dotted decimal format.
Range 7...15
Units characters
Formula for getting internal value
internal_value = gui_value
Default value -
Default value notes -
Related functions -
Modification On-Line
Related parameters -
Parameter relationships -
Related options -
Feature dependencies -
Interfaces • EM <-> FTM • RAC <-> FTM • RAC <-> RACApp
References -
Validation pattern -
Table 150 flexBusIpAddr (Public IP Address of Flexbus Part of BTS)
Parameter name Local UDP port for small packets multiplexing
Table 151 fpLocalUdpPort (Local UDP port for small packets multiplexing)
DN70577885 225
Flexi Transport Module Parameters IPNO Parameters
Id:0900d80580975ffbConfidential
23.9 fpMuxAmount (Maximum amount of small packets that can be multiplexed)
Abbreviated name fpLocalUdpPort
3GPP name -
Managed Object IPNO
Multiplicity 1
Description This parameter specifies the port on which the FTM expects to receive multiplexed frames. Multiplexing small packets shall increase the efficiency when transporting them.
Range 49152... 65535
Units -
Formula for getting internal value
internal_value = gui_value
Default value 65535
Default value notes -
Related functions -
Modification On-Line
Related parameters -
Parameter relationships -
Related options -
Feature dependencies • RAN1886 Efficient Transport for Small IP Packets
Interfaces • EM <-> FTM • RAC <-> FTM • RAC <-> RACApp
References -
Validation pattern -
Table 151 fpLocalUdpPort (Local UDP port for small packets multiplexing) (Cont.)
Parameter name Maximum amount of small packets that can be mul-tiplexed
Abbreviated name fpMuxAmount
3GPP name -
Managed Object IPNO
Table 152 fpMuxAmount (Maximum amount of small packets that can be multiplexed)
226 DN70577885
Flexi Transport Module Parameters
Id:0900d80580975ffbConfidential
IPNO Parameters
23.10 fpMuxDelay (Small packets multiplexing delay time)
Multiplicity 1
Description This parameter specifies the maximum amount of non-multiplexed packets that are multiplexed to a single multiplexed one. Multiplexing small packets shall increase the efficiency when transporting them.
Range 1... 30
Units -
Formula for getting internal value
internal_value = gui_value
Default value 30
Default value notes -
Related functions -
Modification On-Line
Related parameters -
Parameter relationships -
Related options -
Feature dependencies • RAN1886 Efficient Transport for Small IP Packets
Interfaces • EM <-> FTM • RAC <-> FTM • RAC <-> RACApp
References -
Validation pattern -
Table 152 fpMuxAmount (Maximum amount of small packets that can be multiplexed) (Cont.)
Parameter name Small packets multiplexing delay time
Abbreviated name fpMuxDelay
3GPP name -
Managed Object IPNO
Multiplicity 1
Table 153 fpMuxDelay (Small packets multiplexing delay time)
DN70577885 227
Flexi Transport Module Parameters IPNO Parameters
Id:0900d80580975ffbConfidential
23.11 fpRemoteUdpPort (Remote UDP port for small packets multiplexing)
Description This parameter specifies maximum delay time that may elapse before transmitting a multiplexed packet. As long as the timer has not elapsed, the FTM waits for other incoming packets in order to multiplex them additionally with the packet that is wating to be transmitted. Multiplexing small packets shall increase the efficiency when transporting them.
Range 1... 4
Units -
Formula for getting internal value
internal_value = gui_value
Default value 2
Default value notes -
Related functions -
Modification On-Line
Related parameters -
Parameter relationships -
Related options -
Feature dependencies • RAN1886 Efficient Transport for Small IP Packets
Interfaces • EM <-> FTM • RAC <-> FTM • RAC <-> RACApp
References -
Validation pattern -
Table 153 fpMuxDelay (Small packets multiplexing delay time) (Cont.)
Parameter name Remote UDP port for small packets multiplexing
Abbreviated name fpRemoteUdpPort
3GPP name -
Managed Object IPNO
Multiplicity 1
Table 154 fpRemoteUdpPort (Remote UDP port for small packets multiplexing)
228 DN70577885
Flexi Transport Module Parameters
Id:0900d80580975ffbConfidential
IPNO Parameters
23.12 ftmIpAddr (Flexi Transport Module IP Address)
Description This parameter specifies the port of the RNC towards which the FTM sends multiplexed frames. Multiplexing small packets shall increase the effi-ciency when transporting them.
Range 49152... 65535
Units -
Formula for getting internal value
internal_value = gui_value
Default value 65535
Default value notes -
Related functions -
Modification On-Line
Related parameters -
Parameter relationships -
Related options -
Feature dependencies • RAN1886 Efficient Transport for Small IP Packets
Interfaces • EM <-> FTM • RAC <-> FTM • RAC <-> RACApp
References -
Validation pattern -
Table 154 fpRemoteUdpPort (Remote UDP port for small packets multiplexing)
Parameter name Flexi Transport Module IP Address
Abbreviated name ftmIpAddr
3GPP name -
Managed Object IPNO
Multiplicity 1
Description Public IP address of the Flexi Transport Module
Range 7...15
Units characters
Formula for getting internal value
internal_value = gui_value
Default value -
Table 155 ftmIpAddr (Flexi Transport Module IP Address)
DN70577885 229
Flexi Transport Module Parameters IPNO Parameters
Id:0900d80580975ffbConfidential
23.13 ftmNetmask (Netmask of the public IP address)
Default value notes -
Related functions -
Modification On-Line
Related parameters -
Parameter relationships -
Related options -
Feature dependencies -
Interfaces • EM <-> FTM • RAC <-> FTM • RAC <-> RACApp
References -
Validation pattern -
Table 155 ftmIpAddr (Flexi Transport Module IP Address) (Cont.)
Parameter name Netmask of the public IP address
Abbreviated name ftmNetmask
3GPP name -
Managed Object IPNO
Multiplicity 1
Description This parameter specifies the subnet mask of the public IP address of the transport module.
Range 7...15
Units characters
Formula for getting internal value
internal_value = gui_value
Default value -
Default value notes -
Related functions -
Modification On-Line
Related parameters -
Parameter relationships -
Related options -
Feature dependencies -
Table 156 ftmNetmask (Netmask of the public IP address)
230 DN70577885
Flexi Transport Module Parameters
Id:0900d80580975ffbConfidential
IPNO Parameters
23.14 iHSPAAdapterCommissioningParameter (I-HSPA adapter initial commissioning parameters)
Interfaces • EM <-> FTM • RAC <-> FTM • RAC <-> RACApp
References -
Validation pattern -
Table 156 ftmNetmask (Netmask of the public IP address) (Cont.)
Parameter name I-HSPA adapter initial commissioning parameters
Abbreviated name iHSPAAdapterCommissioningParameter
3GPP name -
Managed Object IPNO
Multiplicity 100
Description Defines the parameters which are needed for the initial commissioning of the I-HSPA adapter.
Range 0...255
Units characters
Formula for getting internal value
internal_value = gui_value
Default value -
Default value notes -
Related functions -
Modification BTS restart needed
Related parameters -
Parameter relationships -
Related options • RAN2060 Conversion of a BTS containing FTLB into an I-BTS
Feature dependencies -
Interfaces • EM -> FTM • RAC -> FTM • RAC <-> RACApp
References -
Validation pattern -
Table 157 iHSPAAdapterCommissioningParameter (I-HSPA adapter initial commis-sioning parameters)
DN70577885 231
Flexi Transport Module Parameters IPNO Parameters
Id:0900d80580975ffbConfidential
23.15 iHSPAmode (I-HSPA mode activation flag)
23.16 icmpResponseEnabled (Enable response to ICMP traffic)
Parameter name I-HSPA mode activation flag
Abbreviated name iHSPAmode
3GPP name -
Managed Object IPNO
Multiplicity 1
Description This parameter defines whether the BTS shall be operated in I-HSPA mode.
A prerequisite is that the I-HSPA SW support is enabled. This can be viewed from parameter IPNO - iHSPASwSupport.
Range disabled (0), enabled (1)
Units -
Formula for getting internal value
gui ==> internal
disabled ==> 0
enabled ==> 1
Default value disabled (0)
Default value notes Default is disabled I-HSPA mode.
Related functions -
Modification On-Line
Related parameters -
Parameter relationships -
Related options • RAN2060 Conversion of a BTS containing FTLB into an I-BTS
Feature dependencies -
Interfaces • EM <-> FTM • RAC <-> FTM • RAC <-> RACApp
References -
Validation pattern -
Table 158 iHSPAmode (I-HSPA mode activation flag)
Parameter name Enable response to ICMP traffic
Abbreviated name icmpResponseEnabled
Table 159 icmpResponseEnabled (Enable response to ICMP traffic)
232 DN70577885
Flexi Transport Module Parameters
Id:0900d80580975ffbConfidential
IPNO Parameters
23.17 ipNodeId (IP Node Identifier)
3GPP name -
Managed Object IPNO
Multiplicity 1
Description This parameter controls if the BTS shall respond to ICMP and traceroute requests via BTS Site Manager or SCF or not at all. Value false means: response is disabled.
Range false (0), true (1)
Units -
Formula for getting internal value
• false => 0 • true => 1
Default value true (1)
Default value notes -
Related functions -
Modification On-Line
Related parameters -
Parameter relationships -
Related options -
Feature dependencies -
Interfaces • EM <-> FTM • RAC <-> FTM • RAC <-> RACApp
References -
Validation pattern -
Table 159 icmpResponseEnabled (Enable response to ICMP traffic) (Cont.)
Parameter name IP Node Identifier
Abbreviated name ipNodeId
3GPP name -
Managed Object IPNO
Multiplicity 1
Description This parameter identifies the BTS transport IP node configuration.
The value is always 1.
Range 1... 1
Table 160 ipNodeId (IP Node Identifier)
DN70577885 233
Flexi Transport Module Parameters IPNO Parameters
Id:0900d80580975ffbConfidential
23.18 linkOAMLoopbackSupport (Link OAM remote loopback discovery enabling flag)
Units -
Formula for getting internal value
internal_value = gui_value
Default value -
Default value notes -
Related functions -
Modification Not modifiable
Related parameters -
Parameter relationships -
Related options -
Feature dependencies -
Interfaces • EM <-> FTM • RAC -> FTM • RAC <-> RACApp
References -
Validation pattern -
Table 160 ipNodeId (IP Node Identifier) (Cont.)
Parameter name Link OAM remote loopback discovery enabling flag
Abbreviated name linkOAMLoopbackSupport
3GPP name -
Managed Object IPNO
Multiplicity 1
Description If set to true, the FTM enables the discovery process for Link OAM loopback requests initiated by a remote network element. If set to false, a loopback initiated from the remote network is not accepted by the FTM
NOTE: linkOAMLoopbackSupport flag cannot be "true" in ATM Iub transport mode..
Range false (0), true (1)
Units -
Formula for getting internal value
• false => 0 • true => 1
Table 161 linkOAMLoopbackSupport (Link OAM remote loopback discovery enabling flag)
234 DN70577885
Flexi Transport Module Parameters
Id:0900d80580975ffbConfidential
IPNO Parameters
23.19 mPlaneIpAddress (Management -plane application IP address)
Default value false (0)
Default value notes By default, the FTM does not accept loopbacks ini-tiated from a remote peer.
Related functions -
Modification On-Line
Related parameters iHSPAmode of IPNO - Not supported in case parameter iHSPAmode is set to enabled.
Parameter relationships -
Related options • RAN1880-a Ethernet OAM (Ethernet Link OAM)
Feature dependencies -
Interfaces • EM <-> FTM • RAC <-> FTM • RAC <-> RACApp
References -
Validation pattern -
Table 161 linkOAMLoopbackSupport (Link OAM remote loopback discovery enabling flag) (Cont.)
Parameter name Management -plane application IP address
Abbreviated name mPlaneIpAddress
3GPP name -
Managed Object IPNO
Multiplicity 1
Table 162 mPlaneIpAddress (Management -plane application IP address)
DN70577885 235
Flexi Transport Module Parameters IPNO Parameters
Id:0900d80580975ffbConfidential
23.20 mtu (Maximum transfer unit of the BTS)
Description This parameter specifies the IP address to be used for management-plane traffic by the FTM.
This IP address can collapse with the local IP address of the plain Ethernet interface (IEIF object) or with the local IP address of one of the VLAN interfaces (IVIF object) or with the local IP address of the ML-PPP interface (P3SL or P3ML object) of the FTM. If it does not collapse with such network interface IP address, the IP address is virtual.
The format of this parameter is dotted decimal.
Value 0.0.0.0 means the management-plane appli-cation IP address is not used.
The parameter is not used at all in case of AtmOv-erEthernet (AtmIub) mode.
Range 7...15
Units characters
Formula for getting internal value
internal_value = gui_value
Default value 0.0.0.0
Default value notes By default the management-plane application IP address is not used.
Related functions -
Modification On-Line
Related parameters -
Parameter relationships -
Related options -
Feature dependencies • CN4065
Interfaces • EM <-> FTM • RAC <-> FTM • RAC <-> RACApp
References -
Validation pattern -
Table 162 mPlaneIpAddress (Management -plane application IP address) (Cont.)
Parameter name Maximum transfer unit of the BTS
Abbreviated name mtu
3GPP name -
Table 163 mtu (Maximum transfer unit of the BTS)
236 DN70577885
Flexi Transport Module Parameters
Id:0900d80580975ffbConfidential
IPNO Parameters
23.21 oamCir (Committed information rate for Service OAM messages)
Managed Object IPNO
Multiplicity 1
Description This is the maximum transfer unit that is to be used equally on all IP interfaces of the BTS.
Range 576... 1500
Units octets
Formula for getting internal value
internal_value = gui_value
Default value 1500
Default value notes -
Related functions -
Modification On-Line
Related parameters -
Parameter relationships -
Related options • RAN74 Native Iub IP for Flexi WCDMA BTS • RAN1449 Dual Iub for Flexi WCDMA
Feature dependencies -
Interfaces • EM <-> FTM • RAC <-> FTM • RAC <-> RACApp
References -
Validation pattern -
Table 163 mtu (Maximum transfer unit of the BTS) (Cont.)
Parameter name Committed information rate for Service OAM messages
Abbreviated name oamCir
3GPP name -
Managed Object IPNO
Multiplicity 1
Table 164 oamCir (Committed information rate for Service OAM messages)
DN70577885 237
Flexi Transport Module Parameters IPNO Parameters
Id:0900d80580975ffbConfidential
23.22 oamTlvReply (Optional TLV message reply flag)
Description This parameter specifies the committed information rate (CIR) for Service OAM messages sent by the FTM.
The sum of CIR values of all configured IP inter-faces (IEIF / IVIF) and CIR of Ethernet Service OAM multiplied by 1.2 cannot exceed the available Transport Ethernet interface bandwidth (see IEIF/shapedBandwidth and IEIF/sirTotal ) - Cir of Service OAM is taken in count if there exists at least one OAMMEP in the system.
Range 100... 1000000
Units kbps
Formula for getting internal value
internal_value = gui_value
Default value 1000
Default value notes Default value is 1 Mbps.
Related functions -
Modification On-Line
Related parameters -
Parameter relationships -
Related options • RAN1880-b Ethernet OAM (Ethernet Service OAM)
Feature dependencies -
Interfaces • EM <-> FTM • RAC <-> FTM • RAC <-> RACApp
References -
Validation pattern -
Table 164 oamCir (Committed information rate for Service OAM messages) (Cont.)
Parameter name Optional TLV message reply flag
Abbreviated name oamTlvReply
3GPP name -
Managed Object IPNO
Multiplicity 1
Table 165 oamTlvReply (Optional TLV message reply flag)
238 DN70577885
Flexi Transport Module Parameters
Id:0900d80580975ffbConfidential
IPNO Parameters
23.23 omsTls (TLS usage towards the O&M system)
Description If this parameter is set to true, the optional TLV received in a Link Trace or Loopback message (LTM or LBM message) is sent back unchecked in the corresponding reply message (LTR, or LBR).
If this parameter is set to false, the received optional TLV is ignored and not being sent in the reply-message.
Range false (0), true (1)
Units -
Formula for getting internal value
• false => 0 • true => 1
Default value false (0)
Default value notes By default TLV is ignored.
Related functions -
Modification On-Line
Related parameters -
Parameter relationships -
Related options -
Feature dependencies -
Interfaces • EM <-> FTM • RAC <-> FTM • RAC <-> RACApp
References -
Validation pattern -
Table 165 oamTlvReply (Optional TLV message reply flag) (Cont.)
Parameter name TLS usage towards the O&M system
Abbreviated name omsTls
3GPP name -
Managed Object IPNO
Multiplicity 1
Description Defines the usage of TLS between the BTS and the O&M system.
The usage of TLS requires that valid certificates are installed to the BTS.
Range off (0), forced (1), probing (2)
Table 166 omsTls (TLS usage towards the O&M system)
DN70577885 239
Flexi Transport Module Parameters IPNO Parameters
Id:0900d80580975ffbConfidential
23.24 ret1IpAddr (RET IP Address)
Units -
Formula for getting internal value
gui ==> internal
off ==> 0
forced ==> 1
probing ==> 2
Default value probing (2) for WN7.0 1.0
off (0) for WN7.0 2.0
Default value notes The parameter is in probing mode during autocon-nection.
Related functions -
Modification On-Line
Related parameters iHSPAmode of IPNO - If iHS-PAmode is set to enabled, then omsTls is set to 'off'.
Parameter relationships -
Related options • RAN1102 Secure BTS Management Interface
Feature dependencies -
Interfaces • EM <-> FTM • RAC <-> FTM • RAC <-> RACApp
References -
Validation pattern -
Table 166 omsTls (TLS usage towards the O&M system) (Cont.)
Parameter name RET IP Address
Abbreviated name ret1IpAddr
3GPP name -
Managed Object IPNO
Multiplicity 1
Description IP Address of the RET, which is connected to the Base Station.
Range 7...15
Units characters
Formula for getting internal value
internal_value = gui_value
Table 167 ret1IpAddr (RET IP Address)
240 DN70577885
Flexi Transport Module Parameters
Id:0900d80580975ffbConfidential
IPNO Parameters
23.25 rncIpAddr (RNC IP Address)
Default value -
Default value notes -
Related functions -
Modification On-Line
Related parameters -
Parameter relationships -
Related options -
Feature dependencies -
Interfaces • EM <-> FTM • RAC <-> FTM • RAC <-> RACApp
References -
Validation pattern -
Table 167 ret1IpAddr (RET IP Address) (Cont.)
Parameter name RNC IP Address
Abbreviated name rncIpAddr
3GPP name -
Managed Object IPNO
Multiplicity 1
Description IP Address of the RNC to which the Base Station is connected.
Range 7...15
Units characters
Formula for getting internal value
internal_value = gui_value
Default value -
Default value notes -
Related functions -
Modification On-Line
Related parameters -
Parameter relationships -
Related options -
Feature dependencies -
Table 168 rncIpAddr (RNC IP Address)
DN70577885 241
Flexi Transport Module Parameters IPNO Parameters
Id:0900d80580975ffbConfidential
23.26 sPlaneIpAddress (Synchronization-plane application IP address)
Interfaces • EM <-> FTM • RAC <-> FTM • RAC <-> RACApp
References -
Validation pattern -
Table 168 rncIpAddr (RNC IP Address) (Cont.)
Parameter name Synchronization-plane application IP address
Abbreviated name sPlaneIpAddress
3GPP name -
Managed Object IPNO
Multiplicity 1
Description This parameter specifies the IP address to be used for synchronization-plane traffic by the FTM.
This IP address can collapse with the local IP address of the plain Ethernet interface (IEIF object) or with the local IP address of one of the VLAN interfaces (IVIF object) or with the local IP address of the ML-PPP interface (P3SL or P3ML object) of the FTM. If it does not collapse with such network interface IP address, the IP address is virtual.
The format of this parameter is dotted decimal.
Value 0.0.0.0 means the synchronization-plane application IP address is not used.
The parameter is not used at all in case of AtmOv-erEthernet (AtmIub) mode.
Range 7...15
Units characters
Formula for getting internal value
internal_value = gui_value
Default value 0.0.0.0
Default value notes By default the synchronization-plane application IP address is not used.
Related functions -
Modification On-Line
Table 169 sPlaneIpAddress (Synchronization-plane application IP address)
242 DN70577885
Flexi Transport Module Parameters
Id:0900d80580975ffbConfidential
IPNO Parameters
23.27 transportMode (BTS transport mode)
Related parameters transportMode of IPNO - Parameter sPlaneIpAddress is irrelevant in case parameter transportMode has value AtmOverEthernet.
Parameter relationships -
Related options -
Feature dependencies • CN4065
Interfaces • EM <-> FTM • RAC <-> FTM • RAC <-> RACApp
References -
Validation pattern -
Table 169 sPlaneIpAddress (Synchronization-plane application IP address) (Cont.)
Parameter name BTS transport mode
Abbreviated name transportMode
3GPP name -
Managed Object IPNO
Multiplicity 1
Description This parameter selects between the transport modes AtmOverEthernet, Dual Iub and Iub/IP.
Range AtmOverEthernet (0), DualIub (1), IubIP (2)
Units -
Formula for getting internal value
gui ==> internal
AtmOverEthernet ==> 0
DualIub ==> 1
IubIP ==> 2
Default value AtmOverEthernet (0)
Default value notes -
Related functions -
Modification On-Line
Table 170 transportMode (BTS transport mode)
DN70577885 243
Flexi Transport Module Parameters IPNO Parameters
Id:0900d80580975ffbConfidential
23.28 twampMessageRate (TWAMP initiator rate for sending messages)
Related parameters iHSPAmode of IPNO - If iHS-PAmode is set to enabled then only Iub/IP transport mode is supported.
administrativeState of P3SL - Iub/IP can be enabled only on the modules FTEB, FTHA, FTPB, FTFA when either Multi Link PPP or Single Link PPP is being unlocked.
administrativeState of P3ML - Iub/IP can be enabled only on the modules FTEB, FTHA, FTPB, FTFA when either Multi Link PPP or Single Link PPP is being unlocked.
Parameter relationships -
Related options • RAN74 Native Iub IP for Flexi WCDMA BTS • RAN1449 Dual Iub for Flexi WCDMA
Feature dependencies -
Interfaces • EM <-> FTM • RAC <-> FTM • RAC <-> RACApp
References -
Validation pattern -
Table 170 transportMode (BTS transport mode) (Cont.)
Parameter name TWAMP initiator rate for sending messages
Abbreviated name twampMessageRate
3GPP name -
Managed Object IPNO
Multiplicity 1
Description This parameter specifies the overall rate at which the FTM sends TWAMP initiator messages. The messages are evenly spread over the enabled TWAMP sessions at any given time.
Range RATE_1 (0), RATE_10 (1)
Units -
Formula for getting internal value
gui ==> internal
RATE_1 ==> 0
RATE_10 ==> 1
Table 171 twampMessageRate (TWAMP initiator rate for sending messages)
244 DN70577885
Flexi Transport Module Parameters
Id:0900d80580975ffbConfidential
IPNO Parameters
23.29 twampReflectorOn (TWAMP message response enabling flag)
Default value RATE_10 (1)
Default value notes -
Related functions -
Modification On-Line
Related parameters iHSPAmode of IPNO - Not supported in case parameter iHSPAmode is set to enabled.
Parameter relationships -
Related options -
Feature dependencies • CN4065
Interfaces • EM <-> FTM • RAC <-> FTM • RAC <-> RACApp
References -
Validation pattern -
Table 171 twampMessageRate (TWAMP initiator rate for sending messages) (Cont.)
Parameter name TWAMP message response enabling flag
Abbreviated name twampReflectorOn
3GPP name -
Managed Object IPNO
Multiplicity 1
Description This parameter switches the TWAMP reflector on. The TWAMP reflector shall respond to each received measurement request packet from any sender. The TWAMP reflector re-uses the Sender Sequence Number, Sender Timestamp and Sender Error Estimate fields from the received packet in the response packet.
Range false (0), true (1)
Units -
Formula for getting internal value
• false => 0 • true => 1
Default value true (1)
Default value notes -
Table 172 twampReflectorOn (TWAMP message response enabling flag)
DN70577885 245
Flexi Transport Module Parameters IPNO Parameters
Id:0900d80580975ffbConfidential
23.30 twampReflectorPort (TWAMP reflector port number)
Related functions -
Modification On-Line
Related parameters iHSPAmode of IPNO - Not supported in case parameter iHSPAmode is set to enabled.
Parameter relationships -
Related options • RAN1900 IP Transport Network Measurement
Feature dependencies -
Interfaces • EM <-> FTM • RAC <-> FTM • RAC <-> RACApp
References -
Validation pattern -
Table 172 twampReflectorOn (TWAMP message response enabling flag) (Cont.)
Parameter name TWAMP reflector port number
Abbreviated name twampReflectorPort
3GPP name -
Managed Object IPNO
Multiplicity 1
Description This parameter specifies the source port that is assigned to the TWAMP reflector. The sender on any measurement request packet shall use that port to reach the TWAMP reflector.
Range 1... 65535
Units -
Formula for getting internal value
internal_value = gui_value
Default value 5000
Default value notes IANA-assigned well-known twamp-control port
Related functions -
Modification On-Line
Related parameters iHSPAmode of IPNO - Not supported in case parameter iHSPAmode is set to enabled.
Parameter relationships -
Table 173 twampReflectorPort (TWAMP reflector port number)
246 DN70577885
Flexi Transport Module Parameters
Id:0900d80580975ffbConfidential
IPNO Parameters
23.31 twampSourcePort (TWAMP source port number)
Related options • RAN1900 IP Transport Network Measurement
Feature dependencies -
Interfaces • EM <-> FTM • RAC <-> FTM • RAC <-> RACApp
References -
Validation pattern -
Table 173 twampReflectorPort (TWAMP reflector port number) (Cont.)
Parameter name TWAMP source port number
Abbreviated name twampSourcePort
3GPP name -
Managed Object IPNO
Multiplicity 1
Description This parameter specifies the source port that is used in TWAMP initiator messages. The TWAMP port must be lower than the smallest port number used for regular traffic user plane connections of the FTM.
Range 1... 49151
Units -
Formula for getting internal value
internal_value = gui_value
Default value 49151
Default value notes -
Related functions -
Modification On-Line
Related parameters iHSPAmode of IPNO - Not supported in case parameter iHSPAmode is set to enabled.
Parameter relationships -
Related options • RAN1900 IP Transport Network Measurement
Feature dependencies -
Interfaces • EM <-> FTM • RAC <-> FTM • RAC <-> RACApp
Table 174 twampSourcePort (TWAMP source port number)
DN70577885 247
Flexi Transport Module Parameters IPNO Parameters
Id:0900d80580975ffbConfidential
23.32 uPlane2IpAddress (Second user-plane application IP address)
References -
Validation pattern -
Table 174 twampSourcePort (TWAMP source port number) (Cont.)
Parameter name Second user-plane application IP address
Abbreviated name uPlane2IpAddress
3GPP name -
Managed Object IPNO
Multiplicity 1
Description This parameter specifies a 2nd IP address to be used for user-plane traffic by the FTM.
This IP address can collapse with the local IP address of the plain Ethernet interface (IEIF object) or with the local IP address of one of the VLAN interfaces (IVIF object) or with the local IP address of the ML-PPP interface (P3SL or P3ML object) of the FTM. If it does not collapse with such network interface IP address, the second user-plane IP address is virtual. In the latter case, the assignment to a network interface has to be configured addi-tionally by the operator.
The format of this parameter is dotted decimal.
Value 0.0.0.0 means the 2nd user-plane application IP address is not used at all.
The parameter is not used at all in case of AtmOv-erEthernet (AtmIub) mode.
Range 7...15
Units characters
Formula for getting internal value
internal_value = gui_value
Default value 0.0.0.0
Default value notes By default the second user-plane application IP address is not used.
Related functions -
Modification On-Line
Table 175 uPlane2IpAddress (Second user-plane application IP address)
248 DN70577885
Flexi Transport Module Parameters
Id:0900d80580975ffbConfidential
IPNO Parameters
23.33 uPlane2IpInterface (Second user-plane application IP network interface)
Related parameters transportMode of IPNO - Parameter uPlane2IpAddress is irrelevant in case parameter transportMode has value AtmOverEthernet.
uPlane2IpInterface of IPNO - In case uPlane2IpAddress is a virtual IP address, the operator must configure parameter uPlane2IpInterface too.
Parameter relationships -
Related options -
Feature dependencies • CN4065
Interfaces • EM <-> FTM • RAC <-> FTM • RAC <-> RACApp
References -
Validation pattern -
Table 175 uPlane2IpAddress (Second user-plane application IP address) (Cont.)
Parameter name Second user-plane application IP network interface
Abbreviated name uPlane2IpInterface
3GPP name -
Managed Object IPNO
Multiplicity 1
Table 176 uPlane2IpInterface (Second user-plane application IP network interface)
DN70577885 249
Flexi Transport Module Parameters IPNO Parameters
Id:0900d80580975ffbConfidential
Description This parameter maps the second user-plane IP address to an IP network interface if this IP address is a virtual IP address. This means: the FTM will use the second user-plane application IP address as source IP address in user-plane traffic sent over this interface.
Note that the interface of user-plane traffic is selected based on the entries of the static routing table of the FTM. If it happens to match the value of parameter uPlane2IpInterface, the IP address in parameter uPlane2IpAddress is used in user-plane traffic.
The format of this parameter is local managed object instance identifier (LMOID). The value refer-ences either the plain Ethernet interface (instance of IEIF object class) or a VLAN interface (instance of IVIF object class).
Range 0...40
Units characters
Formula for getting internal value
internal_value = gui_value
Default value -
Default value notes By default the parameter is empty: non-virtual IP addresses for the user-plane application are assumed, i.e. the uPlaneIpAddress collapses with the local IP address of either the plain Ethernet interface or one of the VLAN interfaces.
Related functions -
Modification On-Line
Related parameters uPlane2IpAddress of IPNO - Parameter uPlane2IpInterface must be configured in case parameter uPlane2IpAddress is a virtual IP address.
Parameter relationships -
Related options -
Feature dependencies • CN4065
Interfaces • EM <-> FTM • RAC <-> FTM • RAC <-> RACApp
References -
Validation pattern -
Table 176 uPlane2IpInterface (Second user-plane application IP network interface)
250 DN70577885
Flexi Transport Module Parameters
Id:0900d80580975ffbConfidential
IPNO Parameters
23.34 uPlaneIpAddress (User plane application IP address)
Parameter name User plane application IP address
Abbreviated name uPlaneIpAddress
3GPP name -
Managed Object IPNO
Multiplicity 1
Description This parameter specifies the IP address that is used for user plane traffic by the FTM.
This IP address can collapse with the local IP address of the plain Ethernet interface (IEIF object) or with the local IP address of one of the VLAN interfaces (IVIF object) or with the local IP address of the ML-PPP interface (P3SL or P3ML object) of the FTM. If it does not collapse with such network interface IP address, the second user-plane IP address is virtual. In the latter case, the assignment to a network interface has to be configured addi-tionally by the operator.
The format of this parameter is dotted decimal.
Value 0.0.0.0 means the user-plane application IP address is not used.
The parameter is not used at all in case of AtmOv-erEthernet (AtmIub) mode.
In case the second user-plane IP address is config-ured too, the operator has to additionally assign both the first and the 2nd user plane IP address to an IP network interface.
Range 7...15
Units characters
Formula for getting internal value
internal_value = gui_value
Default value 0.0.0.0
Default value notes By default the user-plane application IP address is not used.
Related functions -
Modification On-Line
Table 177 uPlaneIpAddress (User plane application IP address)
DN70577885 251
Flexi Transport Module Parameters IPNO Parameters
Id:0900d80580975ffbConfidential
23.35 uPlaneIpInterface (User-plane application IP network interface)
Related parameters transportMode of IPNO - Parameter uPlaneIpAddress is irrelevant in case parameter transportMode has value AtmOverEthernet.
uPlaneIpInterface of IPNO - In case uPlane2IpAddress is a virtual IP address, the operator must configure parameter uPlaneIpInter-face too.
Parameter relationships -
Related options -
Feature dependencies • CN4065
Interfaces • EM <-> FTM • RAC <-> FTM • RAC <-> RACApp
References -
Validation pattern -
Table 177 uPlaneIpAddress (User plane application IP address) (Cont.)
Parameter name User-plane application IP network interface
Abbreviated name uPlaneIpInterface
3GPP name -
Managed Object IPNO
Multiplicity 1
Table 178 uPlaneIpInterface (User-plane application IP network interface)
252 DN70577885
Flexi Transport Module Parameters
Id:0900d80580975ffbConfidential
IPNO Parameters
Description This parameter maps the first user-plane IP address to an IP network interface if this IP address is a virtual IP address. This means: the FTM will use the first user-plane application IP address as source IP address in user-plane traffic sent over this interface.
Note that the interface of user-plane traffic is selected based on the entries of the static routing table of the FTM. If it happens to match the value of parameter uPlaneIpInterface, the IP address in parameter uPlaneIpAddress is used in user-plane traffic over that interface.
The format of this parameter is local managed object instance identifier (LMOID). The value refer-ences either the plain Ethernet interface (instance of IEIF object class) or a VLAN interface (instance of IVIF object class).
Range 0...40
Units characters
Formula for getting internal value
internal_value = gui_value
Default value -
Default value notes By default the parameter is empty: non-virtual IP addresses for the user-plane application are assumed, i.e. the uPlaneIpAddress collapses with the local IP address of either the plain Ethernet interface or one of the VLAN interfaces.
Related functions -
Modification On-Line
Related parameters uPlaneIpAddress of IPNO - Parameter uPlaneIpInterface must be configured in case parameter uPlaneIpAddress and uPlane2IpAddress are virtual IP addresses.
uPlane2IpAddress of IPNO - Parameter uPlaneIpInterface must be configured in case parameter uPlaneIpAddress and uPlane2IpAddress are virtual IP addresses.
Parameter relationships -
Related options -
Feature dependencies • CN4065
Table 178 uPlaneIpInterface (User-plane application IP network interface) (Cont.)
DN70577885 253
Flexi Transport Module Parameters IPNO Parameters
Id:0900d80580975ffbConfidential
Interfaces • EM <-> FTM • RAC <-> FTM • RAC <-> RACApp
References -
Validation pattern -
Table 178 uPlaneIpInterface (User-plane application IP network interface) (Cont.)
254 DN70577885
Flexi Transport Module Parameters
Id:0900d80580975ffbConfidential
IPRM Parameters
24 IPRM Parameters
24.1 RmExceptions (Restricted Mode Exception)
Parameter name Restricted Mode Exception
Abbreviated name RmExceptions
3GPP name -
Managed Object IPRM
Multiplicity 32
Description Restricted mode provides protection of the mobile carriers' network against intrusion through inter-faces of the Base Station, in particular the LMT. By default, all traffic to other destinations will be barred.
IPRM allows to configure exceptions, so that defined IP traffic will be allowed, for example com-munication with an LDAP server or administration of other base stations through the LMP of the local one.
Administration of the Restricted Mode consists therefore in defining exceptions from the general blocking of traffic to the outside world.
An RM exception is defined as a far end IP address to/from which traffic is allowed. Port information is not taken into account.
It is possible to define up to 32 exceptions.
NOTE:Exceptions can overlap but they cannot have exactly same configuration.
Formula for getting internal value
-
Default value -
Default value notes -
Related functions -
Child parameters • sourceTwoDiscr • sourceTwoIpAddr • sourceTwoNetMask • userLabel
Modification On-Line
Related parameters -
Parameter relationships -
Table 179 RmExceptions (Restricted Mode Exception)
DN70577885 255
Flexi Transport Module Parameters IPRM Parameters
Id:0900d80580975ffbConfidential
24.2 sourceTwoDiscr (How is source two defined?)
Related options • RAN1749 BTS Firewall
Feature dependencies -
Interfaces • EM <-> FTM • RAC <-> FTM • RAC <-> RACApp
References -
Validation pattern -
Table 179 RmExceptions (Restricted Mode Exception) (Cont.)
Parameter name How is source two defined?
Abbreviated name sourceTwoDiscr
3GPP name -
Managed Object -
Multiplicity 1
Description With this parameter the user can select the way how to define source two.
Possible values are:
SINGLE: a single IP address
RANGE: a range of IP addresses given by an IP address and a subnet mask
WILDCARD: any IP adress is allowed
Range SINGLE (1), RANGE (2), WILDCARD (3)
Units -
Formula for getting internal value
gui ==> internal
SINGLE ==> 1
RANGE ==> 2
WILDCARD ==> 3
Default value SINGLE (1)
Default value notes -
Related functions -
Modification On-Line
Related parameters -
Parameter relationships -
Related options • RAN1749 BTS Firewall
Table 180 sourceTwoDiscr (How is source two defined?)
256 DN70577885
Flexi Transport Module Parameters
Id:0900d80580975ffbConfidential
IPRM Parameters
24.3 sourceTwoIpAddr (IP address for source two)
Feature dependencies -
Interfaces • EM <-> FTM • RAC <-> FTM • RAC <-> RACApp
References -
Validation pattern -
Table 180 sourceTwoDiscr (How is source two defined?) (Cont.)
Parameter name IP address for source two
Abbreviated name sourceTwoIpAddr
3GPP name -
Managed Object -
Multiplicity 1
Description This parameter is meaningful if and only if source two is defined as SINGLE or as RANGE; in all other cases it is ignored.
"IP address source two" specifies a single IP address.
If source two is defined as SINGLE, this is the only allowed IP address.
If source two is defined as RANGE, then the allowed range of IP addresses is obtained by applying the "IP subnet mask for source two" to this IP address.
The IP address must be given as "dotted decimal" string.
NOTE: IP address 0.0.0.0 is not allowed.
Range 7...15
Units characters
Formula for getting internal value
internal_value = gui_value
Default value 0.0.0.0
Default value notes -
Related functions -
Modification On-Line
Related parameters sourceTwoDiscr of IPRM
Table 181 sourceTwoIpAddr (IP address for source two)
DN70577885 257
Flexi Transport Module Parameters IPRM Parameters
Id:0900d80580975ffbConfidential
24.4 sourceTwoNetMask (IP Subnet Mask)
Parameter relationships sourceTwoIpAddr is only relevant if parameter sourceTwoDiscr has value SINGLE or RANGE.
Related options • RAN1749 BTS Firewall
Feature dependencies -
Interfaces • EM <-> FTM • RAC <-> FTM • RAC <-> RACApp
References -
Validation pattern -
Table 181 sourceTwoIpAddr (IP address for source two) (Cont.)
Parameter name IP Subnet Mask
Abbreviated name sourceTwoNetMask
3GPP name -
Managed Object -
Multiplicity 1
Description This parameter is meaningful if and only if source two is defined as RANGE; in all other cases it is ignored.
"IP Subnet Mask" specifies a netmask which, when applied to "IP address for source two" yields the allowed range of far end IP addresses.
The netmask must be entered in dotted decimal format.
NOTE:IP address 255.255.255.255 and 0.0.0.0 are not allowed.
Range 7...15
Units characters
Formula for getting internal value
internal_value = gui_value
Default value 0.0.0.0
Default value notes -
Related functions -
Modification On-Line
Related parameters sourceTwoDiscr of IPRM
Table 182 sourceTwoNetMask (IP Subnet Mask)
258 DN70577885
Flexi Transport Module Parameters
Id:0900d80580975ffbConfidential
IPRM Parameters
24.5 userLabel (User Label)
Parameter relationships SourceTwoNetmask is only meaningfull if parame-ter sourceTwoDiscr has value RANGE. Otherwise sourceTwoNetMask is ignored.
Related options • RAN1749 BTS Firewall
Feature dependencies -
Interfaces • EM <-> FTM • RAC <-> FTM • RAC <-> RACApp
References -
Validation pattern -
Table 182 sourceTwoNetMask (IP Subnet Mask) (Cont.)
Parameter name User Label
Abbreviated name userLabel
3GPP name -
Managed Object -
Multiplicity 1
Description An alphanumeric string asigned by the user to uniquely identify the RM Exception.
(More exactly: only the pair userLabel/sourceOne must be unique)
NOTE:This parameter is a mandatory parameter for exception and it must be unique.
Range 1...40
Units characters
Formula for getting internal value
internal_value = gui_value
Default value -
Default value notes -
Related functions -
Modification On-Line
Related parameters -
Parameter relationships -
Related options • RAN1749 BTS Firewall
Feature dependencies -
Table 183 userLabel (User Label)
DN70577885 259
Flexi Transport Module Parameters IPRM Parameters
Id:0900d80580975ffbConfidential
24.6 iprmId (IP Restricted Mode Identifier)
Interfaces • EM <-> FTM • RAC <-> FTM • RAC <-> RACApp
References -
Validation pattern -
Table 183 userLabel (User Label) (Cont.)
Parameter name IP Restricted Mode Identifier
Abbreviated name iprmId
3GPP name -
Managed Object IPRM
Multiplicity 1
Description This parameter identifies the firewall configuration of the BTS. The value is always 1.
Range 1... 1
Units -
Formula for getting internal value
internal_value = gui_value
Default value -
Default value notes -
Related functions -
Modification Not modifiable
Related parameters -
Parameter relationships -
Related options • RAN1749 BTS Firewall
Feature dependencies -
Interfaces • EM <-> FTM • RAC -> FTM • RAC <-> RACApp
References -
Validation pattern -
Table 184 iprmId (IP Restricted Mode Identifier)
260 DN70577885
Flexi Transport Module Parameters
Id:0900d80580975ffbConfidential
IPRT Parameters
25 IPRT Parameters
25.1 ipRoutingTableId (IP Routing Table Identifier)
Parameter name IP Routing Table Identifier
Abbreviated name ipRoutingTableId
3GPP name -
Managed Object IPRT
Multiplicity 1
Description This parameter identifies an IP routing table of the BTS.
Instance 1 shall only be used for DCN routing, instance 2 shall be used for IP routing. IPRT-1 is not supported in IubIP. "FTEB, FTHA, FTPB, FTFA, FTFB, FTIF and FIIF" are not supported for IPRT-2 in AtmIub mode. "FSM and FSI" are supported for IPRT-2 only in IubIP mode.
NOTE: The routing options should be hidden in IP connectivity test dialog for FTFB,FTIF & FIIF in ATM Iub mode and DCN routing shall be used for test in these 3 units when mode is ATM Iub.
Range 1... 2
Units -
Formula for getting internal value
internal_value = gui_value
Default value -
Default value notes -
Related functions -
Modification Not modifiable
Related parameters transportMode of IPNO - An instance for IP routing shall only be available in transport mode Iub/IP.
iHSPAmode of IPNO - If iHS-PAmode is set to enabled, then only IPRT-2(ipRou-tingTableId=2) is supported.
Parameter relationships -
Related options -
Feature dependencies • IPv4 routing for management traffic, DHCP, NTP
Table 185 ipRoutingTableId (IP Routing Table Identifier)
DN70577885 261
Flexi Transport Module Parameters IPRT Parameters
Id:0900d80580975ffbConfidential
25.2 staticRoutes (List of static routes)
Interfaces • EM <-> FTM • RAC -> FTM • RAC <-> RACApp
References -
Validation pattern -
Table 185 ipRoutingTableId (IP Routing Table Identifier) (Cont.)
Parameter name List of static routes
Abbreviated name staticRoutes
3GPP name -
Managed Object IPRT
Multiplicity 100
Description Contains the list of static (configured) routes.
Formula for getting internal value
-
Default value -
Default value notes -
Related functions -
Child parameters • bfdId • destIpAddr • gateway • netmask • preference
Modification On-Line
Related parameters -
Parameter relationships -
Related options -
Feature dependencies • IPv4 routing for management traffic, DHCP, NTP
Interfaces • EM <-> FTM • RAC <-> FTM • RAC <-> RACApp
References -
Validation pattern -
Table 186 staticRoutes (List of static routes)
262 DN70577885
Flexi Transport Module Parameters
Id:0900d80580975ffbConfidential
IPRT Parameters
25.3 bfdId (BFD route protection session identifier)
25.4 destIpAddr (Route destination IP address)
Parameter name BFD route protection session identifier
Abbreviated name bfdId
3GPP name -
Managed Object -
Multiplicity 1
Description This parameter identifies the Bidirectional Forward-ing Detection (BFD) session that shall protect this route. The parameter value shall match one of the object instance identifiers of the BFD managed object class.
Value 0 means the route is not protected by any BFD session.
Range 0... 16
Units -
Formula for getting internal value
internal_value = gui_value
Default value 0
Default value notes The route is not protected.
Related functions -
Modification On-Line
Related parameters iHSPAmode of IPNO - Not supported in case parameter iHSPAmode is set to enabled.
Parameter relationships -
Related options • RAN2440 Fast IP Rerouting
Feature dependencies -
Interfaces • EM <-> FTM • RAC <-> FTM • RAC <-> RACApp
References -
Validation pattern -
Table 187 bfdId (BFD route protection session identifier)
Parameter name Route destination IP address
Table 188 destIpAddr (Route destination IP address)
DN70577885 263
Flexi Transport Module Parameters IPRT Parameters
Id:0900d80580975ffbConfidential
25.5 gateway (IP address of the next hop of the route)
Abbreviated name destIpAddr
3GPP name -
Managed Object -
Multiplicity 1
Description Specifies the IP address for indirectly connected (point-to-point) IP nodes (remote network). If a default gateway shall be defined, the value is to be set to 0.0.0.0.
Range 7...15
Units characters
Formula for getting internal value
internal_value = gui_value
Default value -
Default value notes -
Related functions -
Modification On-Line
Related parameters -
Parameter relationships -
Related options -
Feature dependencies • IPv4 routing for management traffic, DHCP, NTP
Interfaces • EM <-> FTM • RAC <-> FTM • RAC <-> RACApp
References -
Validation pattern -
Table 188 destIpAddr (Route destination IP address) (Cont.)
Parameter name IP address of the next hop of the route
Abbreviated name gateway
3GPP name -
Managed Object -
Multiplicity 1
Description Specifies the IP address of the next hop via which the route destination Ip address can be reached.
Table 189 gateway (IP address of the next hop of the route)
264 DN70577885
Flexi Transport Module Parameters
Id:0900d80580975ffbConfidential
IPRT Parameters
25.6 netmask (Netmask of the destination IP address)
Range 7...15
Units characters
Formula for getting internal value
internal_value = gui_value
Default value -
Default value notes -
Related functions -
Modification On-Line
Related parameters -
Parameter relationships -
Related options -
Feature dependencies • IPv4 routing for management traffic, DHCP, NTP
Interfaces • EM <-> FTM • RAC <-> FTM • RAC <-> RACApp
References -
Validation pattern -
Table 189 gateway (IP address of the next hop of the route) (Cont.)
Parameter name Netmask of the destination IP address
Abbreviated name netmask
3GPP name -
Managed Object -
Multiplicity 1
Description Specifies the subnet mask of the route destination IP address. If a default gateway shall be defined, the value is to be set to 0.0.0.0.
Range 7...15
Units characters
Formula for getting internal value
internal_value = gui_value
Default value -
Default value notes -
Related functions -
Table 190 netmask (Netmask of the destination IP address)
DN70577885 265
Flexi Transport Module Parameters IPRT Parameters
Id:0900d80580975ffbConfidential
25.7 preference (Preference value for the route)
Modification On-Line
Related parameters -
Parameter relationships -
Related options -
Feature dependencies • IPv4 routing for management traffic, DHCP, NTP
Interfaces • EM <-> FTM • RAC <-> FTM • RAC <-> RACApp
References -
Validation pattern -
Table 190 netmask (Netmask of the destination IP address) (Cont.)
Parameter name Preference value for the route
Abbreviated name preference
3GPP name -
Managed Object -
Multiplicity 1
Description This parameter specifies a preference value for this route. The FTM shall use by preference routes with lower preference value.
Range 1... 254
Units -
Formula for getting internal value
internal_value = gui_value
Default value 1
Default value notes Default value is lowest possible preference value. By default all routes have equally low cost.
Related functions -
Modification On-Line
Related parameters -
Parameter relationships -
Related options • RAN2440 Fast IP Rerouting
Feature dependencies -
Table 191 preference (Preference value for the route)
266 DN70577885
Flexi Transport Module Parameters
Id:0900d80580975ffbConfidential
IPRT Parameters
Interfaces • EM <-> FTM • RAC <-> FTM • RAC <-> RACApp
References -
Validation pattern -
Table 191 preference (Preference value for the route) (Cont.)
DN70577885 267
Flexi Transport Module Parameters IVIF Parameters
Id:0900d80580975ffbConfidential
26 IVIF Parameters
26.1 cESoPSN (CES over PSN flag)
Parameter name CES over PSN flag
Abbreviated name cESoPSN
3GPP name -
Managed Object IVIF
Multiplicity 1
Description This flag specifies if this interface shall be used for CES over PSN. If true, the traffic over this interface will not be shaped.
Beware that still the actual interface that is used for CES over PSN packets is decided via dynamic routing based on the entries of the static routing table of managed object class IPRT.
Range false (0), true (1)
Units -
Formula for getting internal value
• false => 0 • true => 1
Default value false (0)
Default value notes -
Related functions -
Modification On-Line
Related parameters -
Parameter relationships -
Related options • RAN1707 Flexi WCDMA Integrated CESoPSN
Feature dependencies -
Interfaces • EM <-> FTM • RAC <-> FTM • RAC <-> RACApp
References -
Validation pattern -
Table 192 cESoPSN (CES over PSN flag)
268 DN70577885
Flexi Transport Module Parameters
Id:0900d80580975ffbConfidential
IVIF Parameters
26.2 cir (Committed information rate)
Parameter name Committed information rate
Abbreviated name cir
3GPP name -
Managed Object IVIF
Multiplicity 1
Description The VLAN Committed Information Rate ("VLAN CIR") shall define the average rate up to which traffic is delivered by one VLAN. It shall define the guaranteed transport capacity for the VLAN. The parameter is required for dynamic CAC.
The sum of CIR values of all configured IP inter-faces (IEIF / IVIF) and CIR of Ethernet Service OAM multiplied by 1.2 cannot exceed the available Transport Ethernet interface bandwidth (see IEIF/shapedBandwidth and IEIF/sirTotal ) - Cir of Service OAM is taken in count if there exists at least one OAMMEP in the system.
If there are several IP interfaces and shaping is PATH, Connection Admission Control is based on CIR parameter of the IP interface that user plane uses.
Range 0... 1000000
Units kbps
Formula for getting internal value
internal_value = gui_value
Default value 0
Default value notes -
Related functions -
Modification On-Line
Related parameters -
Parameter relationships -
Related options • RAN1709 VLAN Traffic Differentiation
Feature dependencies -
Interfaces • EM <-> FTM • RAC <-> FTM • RAC <-> RACApp
References -
Validation pattern -
Table 193 cir (Committed information rate)
DN70577885 269
Flexi Transport Module Parameters IVIF Parameters
Id:0900d80580975ffbConfidential
26.3 confCost (OSPF configured interface cost)
26.4 helloInterval (OSPF keepalive message transmission interval)
Parameter name OSPF configured interface cost
Abbreviated name confCost
3GPP name -
Managed Object IVIF
Multiplicity 1
Description This parameter specifies the cost used by the inter-face as defined by the operator. Value 0 means "not specified": If OSPF is enabled the cost calculated by the OSPF router shall be used instead.
Range 0... 65535
Units -
Formula for getting internal value
internal_value = gui_value
Default value 0
Default value notes Default means: "not specified by the operator, use OSPF router calculated cost instead".
Related functions -
Modification On-Line
Related parameters -
Parameter relationships -
Related options • RAN1879 Dynamic routing by OSPF
Feature dependencies -
Interfaces • EM <-> FTM • RAC <-> FTM • RAC <-> RACApp
References -
Validation pattern -
Table 194 confCost (OSPF configured interface cost)
Parameter name OSPF keepalive message transmission interval
Abbreviated name helloInterval
3GPP name -
Table 195 helloInterval (OSPF keepalive message transmission interval)
270 DN70577885
Flexi Transport Module Parameters
Id:0900d80580975ffbConfidential
IVIF Parameters
26.5 interfaceArea (OSPF interface area)
Managed Object IVIF
Multiplicity 1
Description This parameter specifies the interval for transmit-ting keepalive ("Hello") messages.
Range 1... 65535
Units -
Formula for getting internal value
internal_value = gui_value
Default value 1
Default value notes -
Related functions -
Modification On-Line
Related parameters routerDeadInterval of IVIF - Router dead interval should be greater than hello interval
Parameter relationships -
Related options -
Feature dependencies -
Interfaces • EM <-> FTM • RAC <-> FTM • RAC <-> RACApp
References -
Validation pattern -
Table 195 helloInterval (OSPF keepalive message transmission interval) (Cont.)
Parameter name OSPF interface area
Abbreviated name interfaceArea
3GPP name -
Managed Object IVIF
Multiplicity 1
Description This parameter specifies the OSPF area to which the interface belongs.
Range 0...15
Units characters
Table 196 interfaceArea (OSPF interface area)
DN70577885 271
Flexi Transport Module Parameters IVIF Parameters
Id:0900d80580975ffbConfidential
26.6 localIpAddr (Local Address of the IP Interface)
Formula for getting internal value
internal_value = gui_value
Default value -
Default value notes Empty value means OSPF is disabled on this inter-face.
Related functions -
Modification On-Line
Related parameters -
Parameter relationships -
Related options • RAN1879 Dynamic routing by OSPF
Feature dependencies -
Interfaces • EM <-> FTM • RAC <-> FTM • RAC <-> RACApp
References -
Validation pattern -
Table 196 interfaceArea (OSPF interface area) (Cont.)
Parameter name Local Address of the IP Interface
Abbreviated name localIpAddr
3GPP name -
Managed Object IVIF
Multiplicity 1
Description This parameter holds the IP address of the BTS in the transport network for this VLAN. It is accompa-nied with a subnet mask.
Range 7...15
Units characters
Formula for getting internal value
internal_value = gui_value
Default value -
Default value notes -
Related functions -
Modification BTS restart needed
Related parameters -
Table 197 localIpAddr (Local Address of the IP Interface)
272 DN70577885
Flexi Transport Module Parameters
Id:0900d80580975ffbConfidential
IVIF Parameters
26.7 mtuMismatchDetection (MTU mismatch detection in use)
Parameter relationships -
Related options • RAN1709 VLAN Traffic Differentiation
Feature dependencies -
Interfaces • EM <-> FTM • RAC <-> FTM • RAC <-> RACApp
References NSN reference: WBTS_TRS_4548
Validation pattern -
Table 197 localIpAddr (Local Address of the IP Interface) (Cont.)
Parameter name MTU mismatch detection in use
Abbreviated name mtuMismatchDetection
3GPP name -
Managed Object IVIF
Multiplicity 1
Description If set to true, this parameter enables OSPF MTU mismatch detection on receiving DBD (Data Base Descriptor) packets on this interface.
Range false (0), true (1)
Units -
Formula for getting internal value
• false => 0 • true => 1
Default value true (1)
Default value notes -
Related functions -
Modification On-Line
Related parameters -
Parameter relationships -
Related options • RAN1879 Dynamic routing by OSPF
Feature dependencies -
Interfaces • EM <-> FTM • RAC <-> FTM • RAC <-> RACApp
References -
Table 198 mtuMismatchDetection (MTU mismatch detection in use)
DN70577885 273
Flexi Transport Module Parameters IVIF Parameters
Id:0900d80580975ffbConfidential
26.8 netmask (IP network mask of the local IP address)
26.9 ospfWithBfd (OSPF uses additionally BFD)
Validation pattern -
Table 198 mtuMismatchDetection (MTU mismatch detection in use) (Cont.)
Parameter name IP network mask of the local IP address
Abbreviated name netmask
3GPP name -
Managed Object IVIF
Multiplicity 1
Description This parameter holds the network mask for the IP address of the BTS in the transport network for this VLAN.
Range 7...15
Units characters
Formula for getting internal value
internal_value = gui_value
Default value -
Default value notes -
Related functions -
Modification BTS restart needed
Related parameters -
Parameter relationships -
Related options • RAN1709 VLAN Traffic Differentiation
Feature dependencies -
Interfaces • EM <-> FTM • RAC <-> FTM • RAC <-> RACApp
References -
Validation pattern -
Table 199 netmask (IP network mask of the local IP address)
Parameter name OSPF uses additionally BFD
Abbreviated name ospfWithBfd
Table 200 ospfWithBfd (OSPF uses additionally BFD)
274 DN70577885
Flexi Transport Module Parameters
Id:0900d80580975ffbConfidential
IVIF Parameters
26.10 proxyArpIpAddrList (List of proxy ARP IP addresses for this interface.)
3GPP name -
Managed Object IVIF
Multiplicity 1
Description If set to true the OSPF router shall use Bidirectional Forwarding Detection (BFD) for detecting link inter-ruptions on this interface. If set to false, the OSPF router only uses keepalive Hello messages.
Range false (0), true (1)
Units -
Formula for getting internal value
• false => 0 • true => 1
Default value false (0)
Default value notes The OSPF router does not use BFD but only Hello messages.
Related functions -
Modification On-Line
Related parameters -
Parameter relationships -
Related options • RAN2359 OSPF enhancements
Feature dependencies -
Interfaces • EM <-> FTM • RAC <-> FTM • RAC <-> RACApp
References -
Validation pattern -
Table 200 ospfWithBfd (OSPF uses additionally BFD) (Cont.)
Parameter name List of proxy ARP IP addresses for this interface.
Abbreviated name proxyArpIpAddrList
3GPP name -
Managed Object IVIF
Multiplicity 16
Table 201 proxyArpIpAddrList (List of proxy ARP IP addresses for this interface.)
DN70577885 275
Flexi Transport Module Parameters IVIF Parameters
Id:0900d80580975ffbConfidential
26.11 qosEnabled (QOS traffic priorisation enabling flag)
Description This parameter holds a list of up to 16 IP addresses that can be used for proxy ARP detection.
The format of each IP address in the list is dotted decimal.
An empty list means the feature is not used.
Range 7...15
Units characters
Formula for getting internal value
internal_value = gui_value
Default value -
Default value notes -
Related functions -
Modification On-Line
Related parameters -
Parameter relationships -
Related options -
Feature dependencies • RAN2083 ProxyARP in BTS
Interfaces • EM <-> FTM • RAC <-> FTM • RAC <-> RACApp
References -
Validation pattern -
Table 201 proxyArpIpAddrList (List of proxy ARP IP addresses for this interface.)
Parameter name QOS traffic priorisation enabling flag
Abbreviated name qosEnabled
3GPP name -
Managed Object IVIF
Multiplicity 1
Table 202 qosEnabled (QOS traffic priorisation enabling flag)
276 DN70577885
Flexi Transport Module Parameters
Id:0900d80580975ffbConfidential
IVIF Parameters
26.12 retransInterval (OSPF LSA retransmission interval)
Description This parameter specifies if multiple queues are used over this interface or only a single one. Multiple queues allow DSCP based traffic priorisa-tion.
Amongst the active interfaces (IEIF or IVIF managed object instances) there shall be at least one and at most 2 interfaces carrying a multiple queue scheduler. So qosEnabled shall have value true for at least one interface and must not have value true on more than 2 interfaces.
Range false (0), true (1)
Units -
Formula for getting internal value
• false => 0 • true => 1
Default value false (0)
Default value notes By default the 6 PHB qeueue scheduler is not installed on a VLAN interface.
Related functions -
Modification On-Line
Related parameters -
Parameter relationships -
Related options • RAN1709 VLAN Traffic Differentiation
Feature dependencies -
Interfaces • EM <-> FTM • RAC <-> FTM • RAC <-> RACApp
References -
Validation pattern -
Table 202 qosEnabled (QOS traffic priorisation enabling flag) (Cont.)
Parameter name OSPF LSA retransmission interval
Abbreviated name retransInterval
3GPP name -
Managed Object IVIF
Multiplicity 1
Table 203 retransInterval (OSPF LSA retransmission interval)
DN70577885 277
Flexi Transport Module Parameters IVIF Parameters
Id:0900d80580975ffbConfidential
26.13 routerDeadInterval (OSPF router read interval)
Description This parameter specifies the value for the retrans-mission of Link State Advertisement (LSA) messages for OSPF. Currently values of 1s and 2s are not supported for LSA retransmission interval .
This issue is to be resolved in the future release of the software.
Range 1... 65535
Units -
Formula for getting internal value
internal_value = gui_value
Default value 5
Default value notes -
Related functions -
Modification On-Line
Related parameters -
Parameter relationships -
Related options • RAN1879 Dynamic routing by OSPF
Feature dependencies -
Interfaces • EM <-> FTM • RAC <-> FTM • RAC <-> RACApp
References -
Validation pattern -
Table 203 retransInterval (OSPF LSA retransmission interval) (Cont.)
Parameter name OSPF router read interval
Abbreviated name routerDeadInterval
3GPP name -
Managed Object IVIF
Multiplicity 1
Description This parameter specifies the value for OSPF router dead interval in seconds. If no hello packet is received within the router dead interval, the link is assumed to be down.
Range 1... 65535
Units -
Table 204 routerDeadInterval (OSPF router read interval)
278 DN70577885
Flexi Transport Module Parameters
Id:0900d80580975ffbConfidential
IVIF Parameters
26.14 sbs (Shaper burst size)
Formula for getting internal value
internal_value = gui_value
Default value 4
Default value notes -
Related functions -
Modification On-Line
Related parameters helloInterval of IVIF - Router dead interval should be greater than hello interval
Parameter relationships -
Related options • RAN1879 Dynamic routing by OSPF
Feature dependencies -
Interfaces • EM <-> FTM • RAC <-> FTM • RAC <-> RACApp
References -
Validation pattern -
Table 204 routerDeadInterval (OSPF router read interval) (Cont.)
Parameter name Shaper burst size
Abbreviated name sbs
3GPP name -
Managed Object IVIF
Multiplicity 1
Description The Traffic Path Shaper Burst Size (SBS) shall define the maximum burst size that is allowed to pass the traffic path shaper.
Range 1522... 2000000
Units octets
Formula for getting internal value
internal_value = gui_value
Default value 1522
Default value notes -
Related functions -
Modification On-Line
Related parameters -
Table 205 sbs (Shaper burst size)
DN70577885 279
Flexi Transport Module Parameters IVIF Parameters
Id:0900d80580975ffbConfidential
26.15 sir (Shaper information rate)
Parameter relationships -
Related options • RAN1709 VLAN Traffic Differentiation
Feature dependencies -
Interfaces • EM <-> FTM • RAC <-> FTM • RAC <-> RACApp
References -
Validation pattern -
Table 205 sbs (Shaper burst size) (Cont.)
Parameter name Shaper information rate
Abbreviated name sir
3GPP name -
Managed Object IVIF
Multiplicity 1
Description The Shaper Information Rate ("VLAN SIR") defines the bandwidth limit to which VLAN traffic is shaped by the traffic path shaper.
For FTLB, the actual minimum egress rate is 1.18 Mbps and on FSM-r3, the actual minimum egress rate is 1.56 Mbps due to technical limitations on Octeon.
Note: The SIRs should be configured to equal the sum of CIR+EIR at the corresponding UNI.
The sum of all SIRs is allowed to exceed the total available bandwidth on the interface (overbooking). Therefore, SIR cannot be guaranteed by the system.
Range 0... 1000000
Units kbps
Formula for getting internal value
internal_value = gui_value
Default value 1000000
Default value notes -
Related functions -
Modification On-Line
Table 206 sir (Shaper information rate)
280 DN70577885
Flexi Transport Module Parameters
Id:0900d80580975ffbConfidential
IVIF Parameters
26.16 transmitDelay (OSPF packet transmission delay)
Related parameters -
Parameter relationships -
Related options • RAN1709 VLAN Traffic Differentiation
Feature dependencies -
Interfaces • EM <-> FTM • RAC <-> FTM • RAC <-> RACApp
References -
Validation pattern -
Table 206 sir (Shaper information rate) (Cont.)
Parameter name OSPF packet transmission delay
Abbreviated name transmitDelay
3GPP name -
Managed Object IVIF
Multiplicity 1
Description This parameter specifies the OSPF transmit delay. This is the amount of time added to the age of an OSPF Link State Update (LSU) packet before transmitting it. It is the estimated number of seconds to transmit a packet over the interface.
Range 1... 65535
Units -
Formula for getting internal value
internal_value = gui_value
Default value 1
Default value notes -
Related functions -
Modification On-Line
Related parameters -
Parameter relationships -
Related options • RAN1879 Dynamic routing by OSPF
Feature dependencies -
Table 207 transmitDelay (OSPF packet transmission delay)
DN70577885 281
Flexi Transport Module Parameters IVIF Parameters
Id:0900d80580975ffbConfidential
26.17 vlanId (VLAN identifier)
Interfaces • EM <-> FTM • RAC <-> FTM • RAC <-> RACApp
References -
Validation pattern -
Table 207 transmitDelay (OSPF packet transmission delay) (Cont.)
Parameter name VLAN identifier
Abbreviated name vlanId
3GPP name -
Managed Object IVIF
Multiplicity 1
Description This parameter holds the VLAN identifier number.
Range 0... 4094
Units -
Formula for getting internal value
internal_value = gui_value
Default value -
Default value notes -
Related functions -
Modification On-Line
Related parameters -
Parameter relationships -
Related options • RAN1709 VLAN Traffic Differentiation
Feature dependencies -
Interfaces • EM <-> FTM • RAC <-> FTM • RAC <-> RACApp
References -
Validation pattern -
Table 208 vlanId (VLAN identifier)
282 DN70577885
Flexi Transport Module Parameters
Id:0900d80580975ffbConfidential
IVIF Parameters
26.18 vlanIfNetId (VLAN interface object identifier)
Parameter name VLAN interface object identifier
Abbreviated name vlanIfNetId
3GPP name -
Managed Object IVIF
Multiplicity 1
Description This parameter identifies the VLAN interface object. Value range is 1 to 7.
Up to 6 VLANs may exist in IP Iub mode. Up to 5 VLANs may exist in Dual Iub mode.
One of the VLAN interfaces is intended to be reserved for FlexiPacket Radio Management.
One of the VLAN interfaces is intended to be reserved for CES over PSN.
Range 1... 7
Units -
Formula for getting internal value
internal_value = gui_value
Default value -
Default value notes -
Related functions -
Modification Not modifiable
Related parameters -
Parameter relationships -
Related options • RAN1709 VLAN Traffic Differentiation • RAN1883 FlexiPacket Radio Management
Feature dependencies -
Interfaces • EM <-> FTM • RAC -> FTM • RAC <-> RACApp
References -
Validation pattern -
Table 209 vlanIfNetId (VLAN interface object identifier)
DN70577885 283
Flexi Transport Module Parameters L2SWI Parameters
Id:0900d80580975ffbConfidential
27 L2SWI Parameters
27.1 dscpMap (DSCP to priority queue map)
Parameter name DSCP to priority queue map
Abbreviated name dscpMap
3GPP name -
Managed Object L2SWI
Multiplicity 64
Description This parameter maps DSCP values to priority queues. The table contains at most 64 entries, one for each possible DSCP value (0..63).
Default values for non-FTLB hardware unit type:
DSCP values 48 and 46 map to priority queue 1, this is the strict priority queue.
DSCP values 38, 36, 34, 30, 28 and 26 map to priority queue 2, this is the first WRR priority queue.
DSCP values 22, 20, 18, 14, 12 and 10 map to priority queue 3, this is the second WRR priority queue.
All other DSCP values map by default to priority queue 4, this is the third WRR priority queue.
Default values for FTLB & FSMr3 hardware unit type:
DSCP values 48 and 46 map to priority queue 1, this is the strict priority queue.
DSCP values 38, 36 and 34 map to priority queue 2, this is the first WRR priority queue.
DSCP values 30, 28 and 26 map to priority queue 3, this is the second WRR priority queue.
DSCP values 22, 20, 18, 14, 12 and 10 map to priority queue 4, this is the third WRR priority queue.
All other DSCP values map by default to priority queue 6, this is the fifth WRR priority queue.
Formula for getting internal value
-
Default value -
Default value notes -
Related functions -
Table 210 dscpMap (DSCP to priority queue map)
284 DN70577885
Flexi Transport Module Parameters
Id:0900d80580975ffbConfidential
L2SWI Parameters
27.2 dscp (DSCP value)
Child parameters • dscp • priorityQueue
Modification On-Line
Related parameters -
Parameter relationships -
Related options • RAN1769 Ethernet Switching
Feature dependencies -
Interfaces • EM <-> FTM • RAC <-> FTM • RAC <-> RACApp
References NSN reference: CN4420 QoS-VLAN Ethernet switching improvement
Validation pattern -
Table 210 dscpMap (DSCP to priority queue map) (Cont.)
Parameter name DSCP value
Abbreviated name dscp
3GPP name -
Managed Object -
Multiplicity 1
Description This parameter specifies a DSCP value.
Range 0... 63
Units -
Formula for getting internal value
internal_value = gui_value
Default value -
Default value notes -
Related functions -
Modification On-Line
Related parameters -
Parameter relationships -
Related options • RAN1769 Ethernet Switching
Feature dependencies -
Table 211 dscp (DSCP value)
DN70577885 285
Flexi Transport Module Parameters L2SWI Parameters
Id:0900d80580975ffbConfidential
27.3 priorityQueue (Priority queue identifier)
Interfaces • EM <-> FTM • RAC <-> FTM • RAC <-> RACApp
References -
Validation pattern -
Table 211 dscp (DSCP value) (Cont.)
Parameter name Priority queue identifier
Abbreviated name priorityQueue
3GPP name -
Managed Object -
Multiplicity 1
Description This parameter specifies a priority queue.
Non-FTLB hardware unit type:
Priority queue values range from 1 to 4 where 4 means lowest and 1 means highest priority. The default value of the parameter = 4.
FTLB & FSMr3 hardware unit type:
Priority queue values range from 1 to 6 where 6 means lowest and 1 means highest priority. The default value of the parameter = 6.
Range 1... 6
Units -
Formula for getting internal value
internal_value = gui_value
Default value 4
Default value notes -
Related functions -
Modification On-Line
Related parameters -
Parameter relationships -
Related options • RAN1769 Ethernet Switching
Feature dependencies -
Table 212 priorityQueue (Priority queue identifier)
286 DN70577885
Flexi Transport Module Parameters
Id:0900d80580975ffbConfidential
L2SWI Parameters
27.4 enableLayer2Switching (Ethernet Switch Enable)
Interfaces • EM <-> FTM • RAC <-> FTM • RAC <-> RACApp
References NSN reference: CN4420 QoS-VLAN Ethernet switching improvement
Validation pattern -
Table 212 priorityQueue (Priority queue identifier) (Cont.)
Parameter name Ethernet Switch Enable
Abbreviated name enableLayer2Switching
3GPP name -
Managed Object L2SWI
Multiplicity 1
Description This parameter indicates if the ethernet link is par-ticipating in the QOS aware layer 2 switch.
Range false (0), true (1)
Units -
Formula for getting internal value
• false => 0 • true => 1
Default value false (0)
Default value notes "false" means the switching is "MAC_ADDRESS" based
Related functions -
Modification On-Line
Related parameters -
Parameter relationships -
Related options • RAN1769 Ethernet Switching
Feature dependencies -
Interfaces • EM <-> FTM • RAC <-> FTM • RAC <-> RACApp
References -
Validation pattern -
Table 213 enableLayer2Switching (Ethernet Switch Enable)
DN70577885 287
Flexi Transport Module Parameters L2SWI Parameters
Id:0900d80580975ffbConfidential
27.5 l2PriorityQueueWeight2 (Layer 2 switch member weight for priority queue 2)
27.6 l2PriorityQueueWeight3 (Layer 2 switch member weight for priority queue 3)
Parameter name Layer 2 switch member weight for priority queue 2
Abbreviated name l2PriorityQueueWeight2
3GPP name -
Managed Object L2SWI
Multiplicity 1
Description This parameter specifies the weight for the 1st priority queue.
Range 1... 8
Units -
Formula for getting internal value
internal_value = gui_value
Default value 8
Default value notes -
Related functions -
Modification On-Line
Related parameters -
Parameter relationships -
Related options • RAN1769 Ethernet Switching
Feature dependencies -
Interfaces • EM <-> FTM • RAC <-> FTM • RAC <-> RACApp
References NSN reference: CN4420 QoS-VLAN Ethernet switching improvement
Validation pattern -
Table 214 l2PriorityQueueWeight2 (Layer 2 switch member weight for priority queue 2)
Parameter name Layer 2 switch member weight for priority queue 3
Abbreviated name l2PriorityQueueWeight3
Table 215 l2PriorityQueueWeight3 (Layer 2 switch member weight for priority queue 3)
288 DN70577885
Flexi Transport Module Parameters
Id:0900d80580975ffbConfidential
L2SWI Parameters
27.7 l2PriorityQueueWeight4 (Layer 2 switch member weight for priority queue 4)
3GPP name -
Managed Object L2SWI
Multiplicity 1
Description This parameter specifies the weight for the second priority queue.
The default value of this parameter = 1 for the FTIB hardware unit.
The default value of this parameter = 4 for the FTLB hardware unit.
Range 1... 8
Units -
Formula for getting internal value
internal_value = gui_value
Default value -
Default value notes The default value of this parameter = 1 for the FTIB hardware unit.The default value of this parameter = 4 for the FTLB hardware unit.
Related functions -
Modification On-Line
Related parameters -
Parameter relationships -
Related options • RAN1769 Ethernet Switching
Feature dependencies -
Interfaces • EM <-> FTM • RAC <-> FTM • RAC <-> RACApp
References NSN reference: CN4420 QoS-VLAN Ethernet switching improvement
Validation pattern -
Table 215 l2PriorityQueueWeight3 (Layer 2 switch member weight for priority queue 3) (Cont.)
Parameter name Layer 2 switch member weight for priority queue 4
Abbreviated name l2PriorityQueueWeight4
Table 216 l2PriorityQueueWeight4 (Layer 2 switch member weight for priority queue 4)
DN70577885 289
Flexi Transport Module Parameters L2SWI Parameters
Id:0900d80580975ffbConfidential
27.8 l2PriorityQueueWeight5 (Layer 2 switch member weight for priority queue 5)
3GPP name -
Managed Object L2SWI
Multiplicity 1
Description This parameter specifies the weight for the third priority queue.
Range 1... 8
Units -
Formula for getting internal value
internal_value = gui_value
Default value 1
Default value notes -
Related functions -
Modification On-Line
Related parameters -
Parameter relationships -
Related options • RAN1769 Ethernet Switching
Feature dependencies -
Interfaces • EM <-> FTM • RAC <-> FTM • RAC <-> RACApp
References NSN reference: CN4420 QoS-VLAN Ethernet switching improvement
Validation pattern -
Table 216 l2PriorityQueueWeight4 (Layer 2 switch member weight for priority queue 4) (Cont.)
Parameter name Layer 2 switch member weight for priority queue 5
Abbreviated name l2PriorityQueueWeight5
3GPP name -
Managed Object L2SWI
Multiplicity 1
Table 217 l2PriorityQueueWeight5 (Layer 2 switch member weight for priority queue 5)
290 DN70577885
Flexi Transport Module Parameters
Id:0900d80580975ffbConfidential
L2SWI Parameters
27.9 l2PriorityQueueWeight6 (Layer 2 switch member weight for priority queue 6)
Description This parameter specifies the weight for the fourth priority queue.
This parameter is only supported for the FTLB hardware unit.
Range 1... 8
Units -
Formula for getting internal value
internal_value = gui_value
Default value 1
Default value notes -
Related functions -
Modification On-Line
Related parameters -
Parameter relationships -
Related options • RAN1769 Ethernet Switching
Feature dependencies -
Interfaces • EM <-> FTM • RAC <-> FTM • RAC <-> RACApp
References NSN reference: CN4420 QoS-VLAN Ethernet switching improvement
Validation pattern -
Table 217 l2PriorityQueueWeight5 (Layer 2 switch member weight for priority queue 5) (Cont.)
Parameter name Layer 2 switch member weight for priority queue 6
Abbreviated name l2PriorityQueueWeight6
3GPP name -
Managed Object L2SWI
Multiplicity 1
Description This parameter specifies the weight for the fifth priority queue.
This parameter is only supported for the FTLB hardware unit.
Table 218 l2PriorityQueueWeight6 (Layer 2 switch member weight for priority queue 6)
DN70577885 291
Flexi Transport Module Parameters L2SWI Parameters
Id:0900d80580975ffbConfidential
27.10 portDefaultPriority (Switch Port Default VLAN Priority (internal Port))
Range 1... 8
Units -
Formula for getting internal value
internal_value = gui_value
Default value 1
Default value notes -
Related functions -
Modification On-Line
Related parameters -
Parameter relationships -
Related options • RAN1769 Ethernet Switching
Feature dependencies -
Interfaces • EM <-> FTM • RAC <-> FTM • RAC <-> RACApp
References NSN reference: CN4420 QoS-VLAN Ethernet switching improvement
Validation pattern -
Table 218 l2PriorityQueueWeight6 (Layer 2 switch member weight for priority queue 6) (Cont.)
Parameter name Switch Port Default VLAN Priority (internal Port)
Abbreviated name portDefaultPriority
3GPP name -
Managed Object L2SWI
Multiplicity 1
Description Default VLAN priority for untagged frames.
Every untagged ingress Ethernet frame at this inter-face gets assigned this Port Default Priority. If QoS classification mode is configured to VLAN-PCP, this priority is used for enqueing decision of the frame. If the frame egresses the switch tagged, this priority shall be used in the VLAN tag header.
Range 0... 7
Units -
Table 219 portDefaultPriority (Switch Port Default VLAN Priority (internal Port))
292 DN70577885
Flexi Transport Module Parameters
Id:0900d80580975ffbConfidential
L2SWI Parameters
27.11 portDefaultVlanId (Switch Port Default VLAN Identifier (internal Port))
Formula for getting internal value
internal_value = gui_value
Default value 0
Default value notes -
Related functions -
Modification On-Line
Related parameters enableLayer2Switching of L2SWI - VLAN aware switching mode should be enabled (enableLayer2Switching="true")
Parameter relationships -
Related options • RAN1769 Ethernet Switching
Feature dependencies -
Interfaces • EM <-> FTM • RAC <-> FTM • RAC <-> RACApp
References NSN reference: CN4420 QoS-VLAN Ethernet switching improvement
Validation pattern -
Table 219 portDefaultPriority (Switch Port Default VLAN Priority (internal Port))
Parameter name Switch Port Default VLAN Identifier (internal Port)
Abbreviated name portDefaultVlanId
3GPP name -
Managed Object L2SWI
Multiplicity 1
Description This parameter specifies the VLAN identifier that is inserted internally by the FTM into an untagged ingress frame that enters the layer 2 switch via this Ethernet interface - if parameter discardUntagged has value false for the Ethernet interface.
In order that the frame will be transmitted via the same or another Ethernet interface, after layer 2 switching has been performed, the same VLAN id must be configured in the VLAN identifier list of that Ethernet interface (see parameter l2VlanIdList). Else the frame will be discarded.
Table 220 portDefaultVlanId (Switch Port Default VLAN Identifier (internal Port))
DN70577885 293
Flexi Transport Module Parameters L2SWI Parameters
Id:0900d80580975ffbConfidential
27.12 priorityQueueNonIP (Priority queue for non-IP frames)
Range 1... 4094
Units -
Formula for getting internal value
internal_value = gui_value
Default value 1
Default value notes Default VLAN id = 1.
Related functions -
Modification On-Line
Related parameters enableLayer2Switching of L2SWI - VLAN aware switching mode should be enabled (enableLayer2Switching="true")
Parameter relationships -
Related options • RAN1769 Ethernet Switching
Feature dependencies -
Interfaces • EM <-> FTM • RAC <-> FTM • RAC <-> RACApp
References NSN reference: CN4420 QoS-VLAN Ethernet switching improvement
Validation pattern -
Table 220 portDefaultVlanId (Switch Port Default VLAN Identifier (internal Port))
Parameter name Priority queue for non-IP frames
Abbreviated name priorityQueueNonIP
3GPP name -
Managed Object L2SWI
Multiplicity 1
Description This parameter specifies which priority queue shall be used for non-IP frames. Non-IP frames examples are ARP-, Ethernet OAM- and Synchro-nous Ethernet messages. The range is
1-6 for FTLB, FSMr3 and
1-4 for all others.
Range 1... 6
Units -
Table 221 priorityQueueNonIP (Priority queue for non-IP frames)
294 DN70577885
Flexi Transport Module Parameters
Id:0900d80580975ffbConfidential
L2SWI Parameters
27.13 priorityQueuePcp0 (Priority queue for ethernet frames with VLAN PCP bits 0)
Formula for getting internal value
internal_value = gui_value
Default value 1
Default value notes The default queue is the strict priority queue. By default non-IP traffic is handled with high priority.
Related functions -
Modification On-Line
Related parameters -
Parameter relationships -
Related options • RAN1769 Ethernet Switching
Feature dependencies -
Interfaces • EM <-> FTM • RAC <-> FTM • RAC <-> RACApp
References NSN reference: CN4420 QoS-VLAN Ethernet switching improvement
Validation pattern -
Table 221 priorityQueueNonIP (Priority queue for non-IP frames) (Cont.)
Parameter name Priority queue for ethernet frames with VLAN PCP bits 0
Abbreviated name priorityQueuePcp0
3GPP name -
Managed Object L2SWI
Multiplicity 1
Description This parameter specifies which priority queue shall be used for ethernet frames with VLAN PCP bits value 0.
The range is
1-6 for FTLB, FSMr3 and
1-4 for all others.
Range 1... 6
Units -
Table 222 priorityQueuePcp0 (Priority queue for ethernet frames with VLAN PCP bits 0)
DN70577885 295
Flexi Transport Module Parameters L2SWI Parameters
Id:0900d80580975ffbConfidential
27.14 priorityQueuePcp1 (Priority queue for ethernet frames with VLAN PCP bits 1)
Formula for getting internal value
internal_value = gui_value
Default value 4
Default value notes The default queue is a Weighted Round Robin priority queue. Default value is 4 for non-FTLB and 6 for FTLB.
Related functions -
Modification On-Line
Related parameters -
Parameter relationships -
Related options • RAN1769 Ethernet Switching
Feature dependencies -
Interfaces • EM <-> FTM • RAC <-> FTM • RAC <-> RACApp
References NSN reference: CN4420 QoS-VLAN Ethernet switching improvement
Validation pattern -
Table 222 priorityQueuePcp0 (Priority queue for ethernet frames with VLAN PCP bits 0) (Cont.)
Parameter name Priority queue for ethernet frames with VLAN PCP bits 1
Abbreviated name priorityQueuePcp1
3GPP name -
Managed Object L2SWI
Multiplicity 1
Description This parameter specifies which priority queue shall be used for ethernet frames with VLAN PCP bits value 1.
The range is
1-6 for FTLB, FSMr3 and
1-4 for all others.
Range 1... 6
Table 223 priorityQueuePcp1 (Priority queue for ethernet frames with VLAN PCP bits 1)
296 DN70577885
Flexi Transport Module Parameters
Id:0900d80580975ffbConfidential
L2SWI Parameters
27.15 priorityQueuePcp2 (Priority queue for ethernet frames with VLAN PCP bits 2)
Units -
Formula for getting internal value
internal_value = gui_value
Default value 4
Default value notes The default queue is a Weighted Round Robin priority queue.
Related functions -
Modification On-Line
Related parameters -
Parameter relationships -
Related options • RAN1769 Ethernet Switching
Feature dependencies -
Interfaces • EM <-> FTM • RAC <-> FTM • RAC <-> RACApp
References NSN reference: CN4420 QoS-VLAN Ethernet switching improvement
Validation pattern -
Table 223 priorityQueuePcp1 (Priority queue for ethernet frames with VLAN PCP bits 1) (Cont.)
Parameter name Priority queue for ethernet frames with VLAN PCP bits 2
Abbreviated name priorityQueuePcp2
3GPP name -
Managed Object L2SWI
Multiplicity 1
Description This parameter specifies which priority queue shall be used for ethernet frames with VLAN PCP bits value 2.
The range is
1-6 for FTLB, FSMr3 and
1-4 for all others.
Range 1... 6
Table 224 priorityQueuePcp2 (Priority queue for ethernet frames with VLAN PCP bits 2)
DN70577885 297
Flexi Transport Module Parameters L2SWI Parameters
Id:0900d80580975ffbConfidential
27.16 priorityQueuePcp3 (Priority queue for ethernet frames with VLAN PCP bits 3)
Units -
Formula for getting internal value
internal_value = gui_value
Default value 3
Default value notes The default queue is a Weighted Round Robin priority queue. Default value is 3 for non-FTLB and 4 for FTLB.
Related functions -
Modification On-Line
Related parameters -
Parameter relationships -
Related options • RAN1769 Ethernet Switching
Feature dependencies -
Interfaces • EM <-> FTM • RAC <-> FTM • RAC <-> RACApp
References NSN reference: CN4420 QoS-VLAN Ethernet switching improvement
Validation pattern -
Table 224 priorityQueuePcp2 (Priority queue for ethernet frames with VLAN PCP bits 2) (Cont.)
Parameter name Priority queue for ethernet frames with VLAN PCP bits 3
Abbreviated name priorityQueuePcp3
3GPP name -
Managed Object L2SWI
Multiplicity 1
Description This parameter specifies which priority queue shall be used for ethernet frames with VLAN PCP bits value 3.
The range is
1-6 for FTLB, FSMr3 and
1-4 for all others.
Table 225 priorityQueuePcp3 (Priority queue for ethernet frames with VLAN PCP bits 3)
298 DN70577885
Flexi Transport Module Parameters
Id:0900d80580975ffbConfidential
L2SWI Parameters
27.17 priorityQueuePcp4 (Priority queue for ethernet frames with VLAN PCP bits 4)
Range 1... 6
Units -
Formula for getting internal value
internal_value = gui_value
Default value 3
Default value notes The default queue is a Weighted Round Robin priority queue. Default value is 3 for non-FTLB and 4 for FTLB.
Related functions -
Modification On-Line
Related parameters -
Parameter relationships -
Related options • RAN1769 Ethernet Switching
Feature dependencies -
Interfaces • EM <-> FTM • RAC <-> FTM • RAC <-> RACApp
References NSN reference: CN4420 QoS-VLAN Ethernet switching improvement
Validation pattern -
Table 225 priorityQueuePcp3 (Priority queue for ethernet frames with VLAN PCP bits 3) (Cont.)
Parameter name Priority queue for ethernet frames with VLAN PCP bits 4
Abbreviated name priorityQueuePcp4
3GPP name -
Managed Object L2SWI
Multiplicity 1
Table 226 priorityQueuePcp4 (Priority queue for ethernet frames with VLAN PCP bits 4)
DN70577885 299
Flexi Transport Module Parameters L2SWI Parameters
Id:0900d80580975ffbConfidential
27.18 priorityQueuePcp5 (Priority queue for ethernet frames with VLAN PCP bits 5)
Description This parameter specifies which priority queue shall be used for ethernet frames with VLAN PCP bits value 4.
The range is
1-6 for FTLB, FSMr3 and
1-4 for all others.
Range 1... 6
Units -
Formula for getting internal value
internal_value = gui_value
Default value 2
Default value notes The default queue is a Weighted Round Robin priority queue. Default value is 2 for non-FTLB and 3 for FTLB.
Related functions -
Modification On-Line
Related parameters -
Parameter relationships -
Related options • RAN1769 Ethernet Switching
Feature dependencies -
Interfaces • EM <-> FTM • RAC <-> FTM • RAC <-> RACApp
References NSN reference: CN4420 QoS-VLAN Ethernet switching improvement
Validation pattern -
Table 226 priorityQueuePcp4 (Priority queue for ethernet frames with VLAN PCP bits 4) (Cont.)
Parameter name Priority queue for ethernet frames with VLAN PCP bits 5
Abbreviated name priorityQueuePcp5
3GPP name -
Managed Object L2SWI
Table 227 priorityQueuePcp5 (Priority queue for ethernet frames with VLAN PCP bits 5)
300 DN70577885
Flexi Transport Module Parameters
Id:0900d80580975ffbConfidential
L2SWI Parameters
27.19 priorityQueuePcp6 (Priority queue for ethernet frames with VLAN PCP bits 6)
Multiplicity 1
Description This parameter specifies which priority queue shall be used for ethernet frames with VLAN PCP bits value 5.
The range is
1-6 for FTLB, FSMr3 and
1-4 for all others.
Range 1... 6
Units -
Formula for getting internal value
internal_value = gui_value
Default value 2
Default value notes The default queue is a Weighted Round Robin priority queue. Default value is 2 for non-FTLB and 3 for FTLB.
Related functions -
Modification On-Line
Related parameters -
Parameter relationships -
Related options • RAN1769 Ethernet Switching
Feature dependencies -
Interfaces • EM <-> FTM • RAC <-> FTM • RAC <-> RACApp
References NSN reference: CN4420 QoS-VLAN Ethernet switching improvement
Validation pattern -
Table 227 priorityQueuePcp5 (Priority queue for ethernet frames with VLAN PCP bits 5) (Cont.)
Parameter name Priority queue for ethernet frames with VLAN PCP bits 6
Abbreviated name priorityQueuePcp6
3GPP name -
Table 228 priorityQueuePcp6 (Priority queue for ethernet frames with VLAN PCP bits 6)
DN70577885 301
Flexi Transport Module Parameters L2SWI Parameters
Id:0900d80580975ffbConfidential
27.20 priorityQueuePcp7 (Priority queue for ethernet frames with VLAN PCP bits 7)
Managed Object L2SWI
Multiplicity 1
Description This parameter specifies which priority queue shall be used for ethernet frames with VLAN PCP bits value 6.
The range is
1-6 for FTLB, FSMr3 and
1-4 for all others.
Range 1... 6
Units -
Formula for getting internal value
internal_value = gui_value
Default value 1
Default value notes The default queue is the strict priority queue. Default value is 1 for non-FTLB and 2 for FTLB.
Related functions -
Modification On-Line
Related parameters -
Parameter relationships -
Related options • RAN1769 Ethernet Switching
Feature dependencies -
Interfaces • EM <-> FTM • RAC <-> FTM • RAC <-> RACApp
References -
Validation pattern -
Table 228 priorityQueuePcp6 (Priority queue for ethernet frames with VLAN PCP bits 6) (Cont.)
Parameter name Priority queue for ethernet frames with VLAN PCP bits 7
Abbreviated name priorityQueuePcp7
3GPP name -
Table 229 priorityQueuePcp7 (Priority queue for ethernet frames with VLAN PCP bits 7)
302 DN70577885
Flexi Transport Module Parameters
Id:0900d80580975ffbConfidential
L2SWI Parameters
27.21 priorityQueueUntagged (Priority queue for untagged ethernet frames)
Managed Object L2SWI
Multiplicity 1
Description This parameter specifies which priority queue shall be used for ethernet frames with VLAN PCP bits value 7.
The range is
1-6 for FTLB, FSMr3 and
1-4 for all others.
Range 1... 6
Units -
Formula for getting internal value
internal_value = gui_value
Default value 1
Default value notes The default queue is the strict priority queue.
Related functions -
Modification On-Line
Related parameters -
Parameter relationships -
Related options • RAN1769 Ethernet Switching
Feature dependencies -
Interfaces • EM <-> FTM • RAC <-> FTM • RAC <-> RACApp
References NSN reference: CN4420 QoS-VLAN Ethernet switching improvement
Validation pattern -
Table 229 priorityQueuePcp7 (Priority queue for ethernet frames with VLAN PCP bits 7) (Cont.)
Parameter name Priority queue for untagged ethernet frames
Abbreviated name priorityQueueUntagged
3GPP name -
Managed Object L2SWI
Multiplicity 1
Table 230 priorityQueueUntagged (Priority queue for untagged ethernet frames)
DN70577885 303
Flexi Transport Module Parameters L2SWI Parameters
Id:0900d80580975ffbConfidential
27.22 qosClassification (QoS Classification Mode)
Description This parameter specifies which priority queue shall be used for untagged ethernet frames.
The range is
1-6 for FTLB, FSMr3 and
1-4 for all others.
Range 1... 6
Units -
Formula for getting internal value
internal_value = gui_value
Default value 1
Default value notes The default queue is the strict priority queue. By default untagged ethernet frames are handled with high priority.
Related functions -
Modification On-Line
Related parameters -
Parameter relationships -
Related options • RAN1769 Ethernet Switching
Feature dependencies -
Interfaces • EM <-> FTM • RAC <-> FTM • RAC <-> RACApp
References NSN reference: CN4420 QoS-VLAN Ethernet switching improvement
Validation pattern -
Table 230 priorityQueueUntagged (Priority queue for untagged ethernet frames)
Parameter name QoS Classification Mode
Abbreviated name qosClassification
3GPP name -
Managed Object L2SWI
Multiplicity 1
Description This parameter specifies if the QOS aware switch-ing is based on DSCP to PHB mapping or on PCP to PHB mapping.
Table 231 qosClassification (QoS Classification Mode)
304 DN70577885
Flexi Transport Module Parameters
Id:0900d80580975ffbConfidential
L2SWI Parameters
27.23 switchId (Layer 2 Switch Object Identifier)
Range DSCP (0), PCP (1)
Units -
Formula for getting internal value
gui ==> internal
DSCP ==> 0
PCP ==> 1
Default value DSCP (0)
Default value notes Default value means DSCP to PHB mapping.
Related functions -
Modification On-Line
Related parameters -
Parameter relationships -
Related options • RAN1769 Ethernet Switching
Feature dependencies -
Interfaces • EM <-> FTM • RAC <-> FTM • RAC <-> RACApp
References -
Validation pattern -
Table 231 qosClassification (QoS Classification Mode) (Cont.)
Parameter name Layer 2 Switch Object Identifier
Abbreviated name switchId
3GPP name -
Managed Object L2SWI
Multiplicity 1
Description This parameter identifies the BTS transport layer 2 switch. The value is always 1.
Range 1... 1
Units -
Formula for getting internal value
internal_value = gui_value
Default value -
Default value notes -
Related functions -
Table 232 switchId (Layer 2 Switch Object Identifier)
DN70577885 305
Flexi Transport Module Parameters L2SWI Parameters
Id:0900d80580975ffbConfidential
27.24 vlanAwareSwitch (VLAN Aware Switching Enable)
Modification Not modifiable
Related parameters -
Parameter relationships -
Related options • RAN1769 Ethernet Switching
Feature dependencies -
Interfaces • EM <-> FTM • RAC -> FTM • RAC <-> RACApp
References -
Validation pattern -
Table 232 switchId (Layer 2 Switch Object Identifier) (Cont.)
Parameter name VLAN Aware Switching Enable
Abbreviated name vlanAwareSwitch
3GPP name -
Managed Object L2SWI
Multiplicity 1
Description This parameter specifies if VLAN information shall be taken into account at the layer 2 switch. By default VLAN information is not taken into account: switching is only based on MAC destination address lookup.
Range false (0), true (1)
Units -
Formula for getting internal value
• false => 0 • true => 1
Default value false (0)
Default value notes Default value is not to include VLAN information in the switching decision.
Related functions -
Modification On-Line
Related parameters -
Parameter relationships -
Related options • RAN1769 Ethernet Switching
Feature dependencies -
Table 233 vlanAwareSwitch (VLAN Aware Switching Enable)
306 DN70577885
Flexi Transport Module Parameters
Id:0900d80580975ffbConfidential
L2SWI Parameters
Interfaces • EM <-> FTM • RAC <-> FTM • RAC <-> RACApp
References -
Validation pattern -
Table 233 vlanAwareSwitch (VLAN Aware Switching Enable) (Cont.)
DN70577885 307
Flexi Transport Module Parameters OAMMA Parameters
Id:0900d80580975ffbConfidential
28 OAMMA Parameters
28.1 assocId (Maintenance association identifier)
28.2 maName (Name of the maintenance domain)
Parameter name Maintenance association identifier
Abbreviated name assocId
3GPP name -
Managed Object OAMMA
Multiplicity 1
Description This parameter identifies an Ethernet service OAM maintenance association. Up to 15 associations may exist in the BTS.
Range 1... 15
Units -
Formula for getting internal value
internal_value = gui_value
Default value -
Default value notes -
Related functions -
Modification Not modifiable
Related parameters -
Parameter relationships -
Related options • RAN1880-b Ethernet OAM (Ethernet Service OAM)
Feature dependencies -
Interfaces • EM <-> FTM • RAC -> FTM • RAC <-> RACApp
References -
Validation pattern -
Table 234 assocId (Maintenance association identifier)
Parameter name Name of the maintenance domain
Abbreviated name maName
3GPP name -
Table 235 maName (Name of the maintenance domain)
308 DN70577885
Flexi Transport Module Parameters
Id:0900d80580975ffbConfidential
OAMMA Parameters
28.3 vlanId (VLAN identifier of the maintenance association)
Managed Object OAMMA
Multiplicity 1
Description This parameter specifies the name of the Mainte-nance Association.
Range 1...42
Units characters
Formula for getting internal value
internal_value = gui_value
Default value -
Default value notes -
Related functions -
Modification On-Line
Related parameters -
Parameter relationships -
Related options • RAN1880-b Ethernet OAM (Ethernet Service OAM)
Feature dependencies -
Interfaces • EM <-> FTM • RAC <-> FTM • RAC <-> RACApp
References -
Validation pattern -
Table 235 maName (Name of the maintenance domain) (Cont.)
Parameter name VLAN identifier of the maintenance association
Abbreviated name vlanId
3GPP name -
Managed Object OAMMA
Multiplicity 1
Table 236 vlanId (VLAN identifier of the maintenance association)
DN70577885 309
Flexi Transport Module Parameters OAMMA Parameters
Id:0900d80580975ffbConfidential
Description This parameter specifies the VLAN identifier that is associated to the Maintenance Association.
The FTM uses this VLAN identifier in the Service OAM messages its sends over the Service OAM ethernet link (configured in the OAMMEP managed object).
Note: The configured VLAN identifier must match the restrictions of the VLAN identifier settings of the Layer 2 bridges of the FTM, in order to prevent that the Service OAM messages are discarded in the bridge.
Range 0... 4094
Units -
Formula for getting internal value
internal_value = gui_value
Default value 0
Default value notes Parameter vlanId = 0 means the maintenance association is not associated to any VLAN.
Related functions -
Modification On-Line
Related parameters -
Parameter relationships -
Related options • RAN1880-b Ethernet OAM (Ethernet Service OAM)
Feature dependencies -
Interfaces • EM <-> FTM • RAC <-> FTM • RAC <-> RACApp
References -
Validation pattern -
Table 236 vlanId (VLAN identifier of the maintenance association) (Cont.)
310 DN70577885
Flexi Transport Module Parameters
Id:0900d80580975ffbConfidential
OAMMD Parameters
29 OAMMD Parameters
29.1 domainId (Maintenance domain identifier)
29.2 mdLevel (Level of the maintenance domain)
Parameter name Maintenance domain identifier
Abbreviated name domainId
3GPP name -
Managed Object OAMMD
Multiplicity 1
Description This parameter identifies an Ethernet service OAM maintenance domain. Up to 10 domains may exist on the BTS.
Range 1... 10
Units -
Formula for getting internal value
internal_value = gui_value
Default value -
Default value notes -
Related functions -
Modification Not modifiable
Related parameters -
Parameter relationships -
Related options • RAN1880-b Ethernet OAM (Ethernet Service OAM)
Feature dependencies -
Interfaces • EM <-> FTM • RAC -> FTM • RAC <-> RACApp
References -
Validation pattern -
Table 237 domainId (Maintenance domain identifier)
Parameter name Level of the maintenance domain
Abbreviated name mdLevel
3GPP name -
Table 238 mdLevel (Level of the maintenance domain)
DN70577885 311
Flexi Transport Module Parameters OAMMD Parameters
Id:0900d80580975ffbConfidential
29.3 mdName (Name of the maintenance domain)
Managed Object OAMMD
Multiplicity 1
Description This parameter specifies the level of the Mainte-nance Domain.
Range 0... 7
Units -
Formula for getting internal value
internal_value = gui_value
Default value -
Default value notes -
Related functions -
Modification On-Line
Related parameters -
Parameter relationships -
Related options • RAN1880-b Ethernet OAM (Ethernet Service OAM)
Feature dependencies -
Interfaces • EM <-> FTM • RAC <-> FTM • RAC <-> RACApp
References -
Validation pattern -
Table 238 mdLevel (Level of the maintenance domain) (Cont.)
Parameter name Name of the maintenance domain
Abbreviated name mdName
3GPP name -
Managed Object OAMMD
Multiplicity 1
Description This parameter specifies the name of the Mainte-nance Domain.
Range 1...42
Units characters
Formula for getting internal value
internal_value = gui_value
Table 239 mdName (Name of the maintenance domain)
312 DN70577885
Flexi Transport Module Parameters
Id:0900d80580975ffbConfidential
OAMMD Parameters
Default value -
Default value notes -
Related functions -
Modification On-Line
Related parameters -
Parameter relationships -
Related options • RAN1880-b Ethernet OAM (Ethernet Service OAM)
Feature dependencies -
Interfaces • EM <-> FTM • RAC <-> FTM • RAC <-> RACApp
References -
Validation pattern -
Table 239 mdName (Name of the maintenance domain) (Cont.)
DN70577885 313
Flexi Transport Module Parameters OAMMEP Parameters
Id:0900d80580975ffbConfidential
30 OAMMEP Parameters
30.1 aisEnabled (AIS message transmission enabling flag)
30.2 aisTxPeriod (AIS messages transmission period)
Parameter name AIS message transmission enabling flag
Abbreviated name aisEnabled
3GPP name -
Managed Object OAMMEP
Multiplicity 1
Description This parameter specifies if the transmission of AIS messages is enabled.
Range false (0), true (1)
Units -
Formula for getting internal value
• false => 0 • true => 1
Default value true (1)
Default value notes -
Related functions -
Modification On-Line
Related parameters -
Parameter relationships -
Related options -
Feature dependencies -
Interfaces • EM <-> FTM • RAC <-> FTM • RAC <-> RACApp
References -
Validation pattern -
Table 240 aisEnabled (AIS message transmission enabling flag)
Parameter name AIS messages period
Abbreviated name aisTxPeriod
3GPP name -
Managed Object OAMMEP
Table 241 aisTxPeriod (AIS messages transmission period)
314 DN70577885
Flexi Transport Module Parameters
Id:0900d80580975ffbConfidential
OAMMEP Parameters
30.3 ccmTxPeriod (Continuity Check Messages transmission period)
Multiplicity 1
Description This parameter specifies the rate for sending AIS messages.
Range AIS_1SEC (0), AIS_1MIN (1)
Units -
Formula for getting internal value
gui ==> internal
AIS_1SEC ==> 0
AIS_1MIN ==> 1
Default value AIS_1SEC (0)
Default value notes -
Related functions -
Modification On-Line
Related parameters -
Parameter relationships -
Related options -
Feature dependencies -
Interfaces • EM <-> FTM • RAC <-> FTM • RAC <-> RACApp
References -
Validation pattern -
Table 241 aisTxPeriod (AIS messages transmission period) (Cont.)
Parameter name Continuity Check Messages transmission period
Abbreviated name ccmTxPeriod
3GPP name -
Managed Object OAMMEP
Multiplicity 1
Description This parameter specifies the period for sending Continuity Check messages (CCMs).
Range CCM_3_33MS (0), CCM_10MS (1), CCM_100MS (2), CCM_1SEC (3), CCM_10SEC (4), CCM_1MIN (5), CCM_10MIN (6)
Units -
Table 242 ccmTxPeriod (Continuity Check Messages transmission period)
DN70577885 315
Flexi Transport Module Parameters OAMMEP Parameters
Id:0900d80580975ffbConfidential
30.4 enableCcm (Allow sending of CCM messages and reset CCM counters)
Formula for getting internal value
gui ==> internal
CCM_3_33MS ==> 0
CCM_10MS ==> 1
CCM_100MS ==> 2
CCM_1SEC ==> 3
CCM_10SEC ==> 4
CCM_1MIN ==> 5
CCM_10MIN ==> 6
Default value CCM_1SEC (3)
Default value notes -
Related functions -
Modification On-Line
Related parameters -
Parameter relationships -
Related options • RAN1880-b Ethernet OAM (Ethernet Service OAM)
Feature dependencies -
Interfaces • EM <-> FTM • RAC <-> FTM • RAC <-> RACApp
References -
Validation pattern -
Table 242 ccmTxPeriod (Continuity Check Messages transmission period) (Cont.)
Parameter name Allow sending of CCM messages and reset CCM counters
Abbreviated name enableCcm
3GPP name -
Managed Object OAMMEP
Multiplicity 1
Table 243 enableCcm (Allow sending of CCM messages and reset CCM counters)
316 DN70577885
Flexi Transport Module Parameters
Id:0900d80580975ffbConfidential
OAMMEP Parameters
30.5 ethernetPort (Ethernet link reference)
Description This parameter allows sending continuity check messages (ETH_CCM) towards the remote Mainte-nance Association Endpoints (MEPs) of the End Point. Changeing the parameter from false (not allowed) to true (allowed) resets the CCM counters of all remote MEPs.
Range false (0), true (1)
Units -
Formula for getting internal value
• false => 0 • true => 1
Default value false (0)
Default value notes By default, sending CCM messages is not allowed.
Related functions -
Modification On-Line
Related parameters -
Parameter relationships -
Related options • RAN1880-b Ethernet OAM (Ethernet Service OAM)
Feature dependencies -
Interfaces • EM <-> FTM • RAC <-> FTM • RAC <-> RACApp
References -
Validation pattern -
Table 243 enableCcm (Allow sending of CCM messages and reset CCM counters)
Parameter name Ethernet link reference
Abbreviated name ethernetPort
3GPP name -
Managed Object OAMMEP
Multiplicity 1
Description This parameter specifies the ethernet link that the FTM shall use for sending Service OAM messages. The parameter is a local managed object instance identifier (LMOID), i.e. a reference to an instance of object class ETHLK. ethernetport cannot be set to FB bit pipe interface.
Table 244 ethernetPort (Ethernet link reference)
DN70577885 317
Flexi Transport Module Parameters OAMMEP Parameters
Id:0900d80580975ffbConfidential
30.6 oammepId (Maintenance association endpoint identifier)
Range 0...40
Units characters
Formula for getting internal value
internal_value = gui_value
Default value -
Default value notes -
Related functions -
Modification On-Line
Related parameters -
Parameter relationships -
Related options • RAN1880-b Ethernet OAM (Ethernet Service OAM)
Feature dependencies -
Interfaces • EM <-> FTM • RAC <-> FTM • RAC <-> RACApp
References -
Validation pattern -
Table 244 ethernetPort (Ethernet link reference) (Cont.)
Parameter name Maintenance association endpoint identifier
Abbreviated name oammepId
3GPP name -
Managed Object OAMMEP
Multiplicity 1
Description This parameter identifies an Ethernet service OAM maintenance association endpoint (MEP).
Range 1... 8191
Units -
Formula for getting internal value
internal_value = gui_value
Default value -
Default value notes -
Related functions -
Table 245 oammepId (Maintenance association endpoint identifier)
318 DN70577885
Flexi Transport Module Parameters
Id:0900d80580975ffbConfidential
OAMMEP Parameters
30.7 remoteMepList (Remote maintenance association end-points list)
Modification Not modifiable
Related parameters -
Parameter relationships -
Related options • RAN1880-b Ethernet OAM (Ethernet Service OAM)
Feature dependencies -
Interfaces • EM <-> FTM • RAC -> FTM • RAC <-> RACApp
References -
Validation pattern -
Table 245 oammepId (Maintenance association endpoint identifier) (Cont.)
Parameter name Remote maintenance association endpoints list
Abbreviated name remoteMepList
3GPP name -
Managed Object OAMMEP
Multiplicity 30
Description This parameter specifies the list of Maintenance Association Endpoints (MEPs) that are contained in the Maintenance Association.
Formula for getting internal value
-
Default value -
Default value notes -
Related functions -
Child parameters • macAddr • mepId
Modification On-Line
Related parameters -
Parameter relationships -
Related options • RAN1880-b Ethernet OAM (Ethernet Service OAM)
Feature dependencies -
Table 246 remoteMepList (Remote maintenance association endpoints list)
DN70577885 319
Flexi Transport Module Parameters OAMMEP Parameters
Id:0900d80580975ffbConfidential
30.8 macAddr (MAC address of the remote MEP)
Interfaces • EM <-> FTM • RAC <-> FTM • RAC <-> RACApp
References -
Validation pattern -
Table 246 remoteMepList (Remote maintenance association endpoints list) (Cont.)
Parameter name MAC address of the remote MEP
Abbreviated name macAddr
3GPP name -
Managed Object -
Multiplicity 1
Description This parameter specifies the MAC address of the remote Maintenance Association End Point (MEP).
Range 17
Units characters
Formula for getting internal value
internal_value = gui_value
Default value -
Default value notes -
Related functions -
Modification On-Line
Related parameters -
Parameter relationships -
Related options • RAN1880-b Ethernet OAM (Ethernet Service OAM)
Feature dependencies -
Interfaces • EM <-> FTM • RAC <-> FTM • RAC <-> RACApp
References -
Validation pattern -
Table 247 macAddr (MAC address of the remote MEP)
320 DN70577885
Flexi Transport Module Parameters
Id:0900d80580975ffbConfidential
OAMMEP Parameters
30.9 mepId (Remote maintenance association endpoint identi-fier)
30.10 vlanPrio (VLAN PCP bits)
Parameter name Remote maintenance association endpoint identi-fier
Abbreviated name mepId
3GPP name -
Managed Object -
Multiplicity 1
Description This parameter specifies the identifier of the remote Maintenance Association End Point (MEP).
Range 1... 8191
Units -
Formula for getting internal value
internal_value = gui_value
Default value -
Default value notes -
Related functions -
Modification On-Line
Related parameters -
Parameter relationships -
Related options • RAN1880-b Ethernet OAM (Ethernet Service OAM)
Feature dependencies -
Interfaces • EM <-> FTM • RAC <-> FTM • RAC <-> RACApp
References -
Validation pattern -
Table 248 mepId (Remote maintenance association endpoint identifier)
Parameter name VLAN PCP bits
Abbreviated name vlanPrio
3GPP name -
Managed Object OAMMEP
Table 249 vlanPrio (VLAN PCP bits)
DN70577885 321
Flexi Transport Module Parameters OAMMEP Parameters
Id:0900d80580975ffbConfidential
Multiplicity 1
Description This parameter specifies the PCP bits value to be used for Service OAM messages for this Mainte-nance association Endpoint (MEP).
Range 0... 7
Units -
Formula for getting internal value
internal_value = gui_value
Default value 7
Default value notes -
Related functions -
Modification On-Line
Related parameters -
Parameter relationships -
Related options -
Feature dependencies -
Interfaces • EM <-> FTM • RAC <-> FTM • RAC <-> RACApp
References -
Validation pattern -
Table 249 vlanPrio (VLAN PCP bits) (Cont.)
322 DN70577885
Flexi Transport Module Parameters
Id:0900d80580975ffbConfidential
OAMPRF Parameters
31 OAMPRF Parameters
31.1 activeMode (Link OAM operational mode at local peer)
Parameter name Link OAM operational mode at local peer
Abbreviated name activeMode
3GPP name -
Managed Object OAMPRF
Multiplicity 1
Description This parameter specifies the Link OAM operational mode at the local peer. If false the BTS shall only respond to a remotely initiated discovery process, if active the BTS shall itself initiate the process.
Range false (0), true (1)
Units -
Formula for getting internal value
• false => 0 • true => 1
Default value false (0)
Default value notes -
Related functions -
Modification On-Line
Related parameters -
Parameter relationships -
Related options • RAN1880-a Ethernet OAM (Ethernet Link OAM)
Feature dependencies -
Interfaces • EM <-> FTM • RAC <-> FTM • RAC <-> RACApp
References -
Validation pattern -
Table 250 activeMode (Link OAM operational mode at local peer)
DN70577885 323
Flexi Transport Module Parameters OAMPRF Parameters
Id:0900d80580975ffbConfidential
31.2 alarmClearanceDelay (Link OAM Link Critical Event Alarm clearance delay)
31.3 efEventThreshold (Errored Frame Event counting thresh-old)
Parameter name Link OAM Link Critical Event Alarm clearance delay
Abbreviated name alarmClearanceDelay
3GPP name -
Managed Object OAMPRF
Multiplicity 1
Description This parameter specifies for how long critical event flags must have been cleared before the FTM will clear the corresponding Link OAM Critical Event alarm.
Range 1... 10
Units seconds
Formula for getting internal value
internal_value = gui_value
Default value 1
Default value notes -
Related functions -
Modification On-Line
Related parameters -
Parameter relationships -
Related options -
Feature dependencies -
Interfaces • EM <-> FTM • RAC <-> FTM • RAC <-> RACApp
References -
Validation pattern -
Table 251 alarmClearanceDelay (Link OAM Link Critical Event Alarm clearance delay)
Parameter name Errored Frame Event counting threshold
Abbreviated name efEventThreshold
Table 252 efEventThreshold (Errored Frame Event counting threshold)
324 DN70577885
Flexi Transport Module Parameters
Id:0900d80580975ffbConfidential
OAMPRF Parameters
31.4 efEventWindow (Errored Frame Event counting interval)
3GPP name -
Managed Object OAMPRF
Multiplicity 1
Description This parameter specifies the threshold value for counting the Errored Frame Event. If the number of errored frames detected within the measurement window specified by efEventWindow is exceeded, the BTS transmits an OAM PDU Event Notification message for that event.
The maximum value of efEventThreshold equals "32 bit value".
Range 0... 4294967295
Units -
Formula for getting internal value
internal_value = gui_value
Default value 1
Default value notes -
Related functions -
Modification On-Line
Related parameters -
Parameter relationships -
Related options -
Feature dependencies -
Interfaces • EM <-> FTM • RAC <-> FTM • RAC <-> RACApp
References -
Validation pattern -
Table 252 efEventThreshold (Errored Frame Event counting threshold) (Cont.)
Parameter name Errored Frame Event counting interval
Abbreviated name efEventWindow
3GPP name -
Managed Object OAMPRF
Multiplicity 1
Table 253 efEventWindow (Errored Frame Event counting interval)
DN70577885 325
Flexi Transport Module Parameters OAMPRF Parameters
Id:0900d80580975ffbConfidential
31.5 efpEventThreshold (Errored Frame Period Event counting threshold)
Description This parameter specifies the measurement interval for counting the Errored Frame Event. If the number of errored frames detected within the measurement interval exceeds the threshold number specified in parameter efEventThreshold, the FTM transmits an OAM PDU Event Notification message for that event.
Range 1... 60
Units seconds
Formula for getting internal value
internal_value = gui_value
Default value 1
Default value notes -
Related functions -
Modification On-Line
Related parameters -
Parameter relationships -
Related options -
Feature dependencies -
Interfaces • EM <-> FTM • RAC <-> FTM • RAC <-> RACApp
References -
Validation pattern -
Table 253 efEventWindow (Errored Frame Event counting interval) (Cont.)
Parameter name Errored Frame Period Event counting threshold
Abbreviated name efpEventThreshold
3GPP name -
Managed Object OAMPRF
Multiplicity 1
Table 254 efpEventThreshold (Errored Frame Period Event counting threshold)
326 DN70577885
Flexi Transport Module Parameters
Id:0900d80580975ffbConfidential
OAMPRF Parameters
31.6 efpEventWindow (Errored Frame Period Event counting interval)
Description This parameter specifies the threshold value for counting the Errored Frame Period Event. If the number of received errored frames within the mea-surement window specified by efpEventWindow is exceeded, the BTS transmits an OAM PDU Event Notification message for that event.
The maximum value of efpEventThreshold equals "32 bit value".
Range 0... 4294967295
Units -
Formula for getting internal value
internal_value = gui_value
Default value 1
Default value notes -
Related functions -
Modification On-Line
Related parameters efpEventWindow of OAMPRF - Configured value for efpEventThreshold should be within configured value for OAMPRF-efpEventWin-dow to enable the possibility of generating Errored Frame Period Event Notifications
Parameter relationships -
Related options -
Feature dependencies -
Interfaces • EM <-> FTM • RAC <-> FTM • RAC <-> RACApp
References -
Validation pattern -
Table 254 efpEventThreshold (Errored Frame Period Event counting threshold)
Parameter name Errored Frame Period Event counting interval
Abbreviated name efpEventWindow
3GPP name -
Managed Object OAMPRF
Multiplicity 1
Table 255 efpEventWindow (Errored Frame Period Event counting interval)
DN70577885 327
Flexi Transport Module Parameters OAMPRF Parameters
Id:0900d80580975ffbConfidential
31.7 efssEventThreshold (Errored Frame Seconds Summary Event counting threshold)
Description This parameter specifies the measurement interval for counting the Errored Frames. If the number of received errored frames within the measurement interval exceeds the threshold number specified in parameter efpEventThreshold, the BTS transmits an OAM PDU Event Notification message for that event.
Range 1... 4294967295
Units -
Formula for getting internal value
internal_value = gui_value
Default value 1
Default value notes -
Related functions -
Modification On-Line
Related parameters -
Parameter relationships -
Related options -
Feature dependencies -
Interfaces • EM <-> FTM • RAC <-> FTM • RAC <-> RACApp
References -
Validation pattern -
Table 255 efpEventWindow (Errored Frame Period Event counting interval) (Cont.)
Parameter name Errored Frame Seconds Summary Event counting threshold
Abbreviated name efssEventThreshold
3GPP name -
Managed Object OAMPRF
Multiplicity 1
Table 256 efssEventThreshold (Errored Frame Seconds Summary Event counting threshold)
328 DN70577885
Flexi Transport Module Parameters
Id:0900d80580975ffbConfidential
OAMPRF Parameters
31.8 efssEventWindow (Errored Frame Seconds Summary Event counting interval)
Description This parameter specifies the threshold value for counting the Errored Frame Seconds Summary Event. If the number of errored frame seconds that occurred during the specified measurement interval specified by efssEventWindow is exceeded, the BTS transmits an OAM PDU Event Notification message for that event.
The maximum value of efssEventThreshold equals "16 bit value".
Range 0... 65535
Units -
Formula for getting internal value
internal_value = gui_value
Default value 1
Default value notes -
Related functions -
Modification On-Line
Related parameters -
Parameter relationships -
Related options -
Feature dependencies -
Interfaces • EM <-> FTM • RAC <-> FTM • RAC <-> RACApp
References -
Validation pattern -
Table 256 efssEventThreshold (Errored Frame Seconds Summary Event counting threshold) (Cont.)
Parameter name Errored Frame Seconds Summary Event counting interval
Abbreviated name efssEventWindow
3GPP name -
Managed Object OAMPRF
Multiplicity 1
Table 257 efssEventWindow (Errored Frame Seconds Summary Event counting interval)
DN70577885 329
Flexi Transport Module Parameters OAMPRF Parameters
Id:0900d80580975ffbConfidential
31.9 eventRepetition (OAM PDU message transmission rate)
Description This parameter specifies the measurement interval for counting the Errored Frame Seconds Summary Event. If the number of errored frame seconds that occurred during the specified measurement interval exceeds the threshold number specified in param-eter efssEventThreshold, the BTS transmits an OAM PDU Event Notification message for that event.
Range 10... 900
Units seconds
Formula for getting internal value
internal_value = gui_value
Default value 60
Default value notes -
Related functions -
Modification On-Line
Related parameters -
Parameter relationships -
Related options -
Feature dependencies -
Interfaces • EM <-> FTM • RAC <-> FTM • RAC <-> RACApp
References -
Validation pattern -
Table 257 efssEventWindow (Errored Frame Seconds Summary Event counting interval) (Cont.)
Parameter name OAM PDU message transmission rate
Abbreviated name eventRepetition
3GPP name -
Managed Object OAMPRF
Multiplicity 1
Table 258 eventRepetition (OAM PDU message transmission rate)
330 DN70577885
Flexi Transport Module Parameters
Id:0900d80580975ffbConfidential
OAMPRF Parameters
31.10 eventSupport (Link OAM event support flag)
Description This parameter specifies how often the FTM repeats the transmission of OAM Events Notifica-tions to its remote peer to increase the probability that they are received by the remote peer. The parameter specifies the total number of repetitive transmissions of such messages.
Range 1... 4
Units -
Formula for getting internal value
internal_value = gui_value
Default value 2
Default value notes -
Related functions -
Modification On-Line
Related parameters activeMode of OAMPRF - Parameter eventRepetition is only relevant in Link OAM active mode (parameter activeMode = true).
Parameter relationships -
Related options -
Feature dependencies -
Interfaces • EM <-> FTM • RAC <-> FTM • RAC <-> RACApp
References -
Validation pattern -
Table 258 eventRepetition (OAM PDU message transmission rate) (Cont.)
Parameter name Link OAM event support flag
Abbreviated name eventSupport
3GPP name -
Managed Object OAMPRF
Multiplicity 1
Description This parameter specifies if the FTM supports Link OAM events.
Range false (0), true (1)
Units -
Table 259 eventSupport (Link OAM event support flag)
DN70577885 331
Flexi Transport Module Parameters OAMPRF Parameters
Id:0900d80580975ffbConfidential
31.11 linkLostTime (Link OAM link lost time)
Formula for getting internal value
• false => 0 • true => 1
Default value false (0)
Default value notes -
Related functions -
Modification On-Line
Related parameters -
Parameter relationships -
Related options -
Feature dependencies -
Interfaces • EM <-> FTM • RAC <-> FTM • RAC <-> RACApp
References -
Validation pattern -
Table 259 eventSupport (Link OAM event support flag) (Cont.)
Parameter name Link OAM link lost time
Abbreviated name linkLostTime
3GPP name -
Managed Object OAMPRF
Multiplicity 1
Description This parameter specifies the time for raising the Link OAM Link Lost Alarm. The Alarm shall be raised if no Link OAM PDUs are received for a period equal to linkLostTime. The alarm shall be cleared if Link OAM PDUs have been continuously received again for the same period of time.
Range 2... 10
Units seconds
Formula for getting internal value
internal_value = gui_value
Default value 10
Default value notes -
Related functions -
Table 260 linkLostTime (Link OAM link lost time)
332 DN70577885
Flexi Transport Module Parameters
Id:0900d80580975ffbConfidential
OAMPRF Parameters
31.12 linkOAMProfileName (Link OAM Profile Name)
Modification On-Line
Related parameters -
Parameter relationships -
Related options -
Feature dependencies -
Interfaces • EM <-> FTM • RAC <-> FTM • RAC <-> RACApp
References -
Validation pattern -
Table 260 linkLostTime (Link OAM link lost time) (Cont.)
Parameter name Link OAM Profile Name
Abbreviated name linkOAMProfileName
3GPP name -
Managed Object OAMPRF
Multiplicity 1
Description This parameter is available in WN7.0 2.0 release.
This parameter describes a unique configurable name for each link OAM profile.
Range 1...40
Units characters
Formula for getting internal value
internal_value = gui_value
Default value -
Default value notes -
Related functions -
Modification On-Line
Related parameters -
Parameter relationships -
Related options • RAN1880-a Ethernet OAM (Ethernet Link OAM)
Feature dependencies -
Table 261 linkOAMProfileName (Link OAM Profile Name)
DN70577885 333
Flexi Transport Module Parameters OAMPRF Parameters
Id:0900d80580975ffbConfidential
31.13 loopBackTime (Link OAM loopback duration)
Interfaces • FTM <-> EM • RAC <-> FTM • RAC <-> RACApp
References -
Validation pattern -
Table 261 linkOAMProfileName (Link OAM Profile Name) (Cont.)
Parameter name Link OAM loopback duration
Abbreviated name loopBackTime
3GPP name -
Managed Object OAMPRF
Multiplicity 1
Description This timer is relevant for Loopback mode either ini-tiated by the BTS or initiated by the Peer.
When BTS initiates the Loopback mode (remote end is in looped state), the loopback time defines the maximum duration of the loopback. After expiry of this timer ("timeout"), the BTS will terminate the Loopback by sending a Loopback Control Disable PDU to the Peer.
When the peer initiates the Loopback mode(BTS is in looped state), the BTS receives a Loopback Control Enable PDU from the Peer and sends an Information PDU back including updated state information. The Loopback mode will be exited if one of the following conditions apply:
(i) The peer sends a Loopback Control Disable PDU to the BTS within the loopback timeout timer
(ii)The loopback timeout timer expires and the BTS exists the loopback mode by sending an Informa-tion OAM PDU to the peer including updated state information. This case is not standardized, but it has been included to avoid the BTS remaining in Loopback mode forever, in case the remote end does not send a Control Disable PDU or it gets lost.
Range 10... 600
Units seconds
Formula for getting internal value
internal_value = gui_value
Table 262 loopBackTime (Link OAM loopback duration)
334 DN70577885
Flexi Transport Module Parameters
Id:0900d80580975ffbConfidential
OAMPRF Parameters
31.14 profileId (Profile instance identifier)
Default value 10
Default value notes -
Related functions -
Modification On-Line
Related parameters activeMode of OAMPRF - Parameter loopBackTime is only relevant in Link OAM active mode (parameter activeMode = true).
Parameter relationships -
Related options -
Feature dependencies -
Interfaces • EM <-> FTM • RAC <-> FTM • RAC <-> RACApp
References -
Validation pattern -
Table 262 loopBackTime (Link OAM loopback duration) (Cont.)
Parameter name Profile instance identifier
Abbreviated name profileId
3GPP name -
Managed Object OAMPRF
Multiplicity 1
Description This parameter identifies an Ethernet link OAM profile.
Range 1... 5
Units -
Formula for getting internal value
internal_value = gui_value
Default value -
Default value notes -
Related functions -
Modification Not modifiable
Related parameters -
Parameter relationships -
Related options -
Table 263 profileId (Profile instance identifier)
DN70577885 335
Flexi Transport Module Parameters OAMPRF Parameters
Id:0900d80580975ffbConfidential
31.15 testFrameRate (Link OAM loopback test message rate)
Feature dependencies -
Interfaces • EM <-> FTM • RAC -> FTM • RAC <-> RACApp
References -
Validation pattern -
Table 263 profileId (Profile instance identifier) (Cont.)
Parameter name Link OAM loopback test message rate
Abbreviated name testFrameRate
3GPP name -
Managed Object OAMPRF
Multiplicity 1
Description This parameter specifies the number of frames / second to be sent during loopback operation for Link OAM.
Value 0 switched the test frame generator off.
Range 0... 25000
Units -
Formula for getting internal value
internal_value = gui_value
Default value 1
Default value notes -
Related functions -
Modification On-Line
Related parameters -
Parameter relationships -
Related options • RAN1880-a Ethernet OAM (Ethernet Link OAM)
Feature dependencies -
Interfaces • EM <-> FTM • RAC <-> FTM • RAC <-> RACApp
References -
Validation pattern -
Table 264 testFrameRate (Link OAM loopback test message rate)
336 DN70577885
Flexi Transport Module Parameters
Id:0900d80580975ffbConfidential
OAMPRF Parameters
31.16 testFrameSize (Link OAM loopback test message frame size)
Parameter name Link OAM loopback test message frame size
Abbreviated name testFrameSize
3GPP name -
Managed Object OAMPRF
Multiplicity 1
Description This parameter specifies the ethernet frame size of test messages sent during loopback operation for Link OAM.
Range 64... 1518
Units -
Formula for getting internal value
internal_value = gui_value
Default value 64
Default value notes Default is minimum PDU size.
Related functions -
Modification On-Line
Related parameters -
Parameter relationships -
Related options • RAN1880-a Ethernet OAM (Ethernet Link OAM)
Feature dependencies -
Interfaces • EM <-> FTM • RAC <-> FTM • RAC <-> RACApp
References -
Validation pattern -
Table 265 testFrameSize (Link OAM loopback test message frame size)
DN70577885 337
Flexi Transport Module Parameters OSPFV2 Parameters
Id:0900d80580975ffbConfidential
32 OSPFV2 Parameters
32.1 confPref (OSPF routing preference value)
32.2 ospfAreas (OSPF area list)
Parameter name OSPF routing preference value
Abbreviated name confPref
3GPP name -
Managed Object OSPFV2
Multiplicity 1
Description This parameter specifies the preference value of the OSPF protocol. The preference value is used in calculating the cost of an OSPF based route.
NOTE: Any change to this parameter causes OSPF daemon restart. It may cause temporary connectiv-ity loss depending on routing configuration.
Range 1... 254
Units -
Formula for getting internal value
internal_value = gui_value
Default value 110
Default value notes -
Related functions -
Modification On-Line
Related parameters -
Parameter relationships -
Related options • RAN1879 Dynamic routing by OSPF
Feature dependencies -
Interfaces • EM <-> FTM • RAC <-> FTM • RAC <-> RACApp
References -
Validation pattern -
Table 266 confPref (OSPF routing preference value)
Parameter name OSPF area list
Table 267 ospfAreas (OSPF area list)
338 DN70577885
Flexi Transport Module Parameters
Id:0900d80580975ffbConfidential
OSPFV2 Parameters
32.3 areaId (OSPF area identifier)
Abbreviated name ospfAreas
3GPP name -
Managed Object OSPFV2
Multiplicity 1
Description This parameter specifies the properties of all OSPF areas configured for the OSPF router. In this release only 1 area is supported.
Formula for getting internal value
-
Default value -
Default value notes -
Related functions -
Child parameters • areaId • areaStub
Modification On-Line
Related parameters -
Parameter relationships -
Related options • RAN1879 Dynamic routing by OSPF
Feature dependencies -
Interfaces • EM <-> FTM • RAC <-> FTM • RAC <-> RACApp
References -
Validation pattern -
Table 267 ospfAreas (OSPF area list) (Cont.)
Parameter name OSPF area identifier
Abbreviated name areaId
3GPP name -
Managed Object -
Multiplicity 1
Description This parameter specifies a unique identifier for the OSPF area in IP notation.
Range 7...15
Units characters
Table 268 areaId (OSPF area identifier)
DN70577885 339
Flexi Transport Module Parameters OSPFV2 Parameters
Id:0900d80580975ffbConfidential
32.4 areaStub (OSPF area stub flag)
Formula for getting internal value
internal_value = gui_value
Default value -
Default value notes -
Related functions -
Modification On-Line
Related parameters -
Parameter relationships -
Related options • RAN1879 Dynamic routing by OSPF
Feature dependencies -
Interfaces • EM <-> FTM • RAC <-> FTM • RAC <-> RACApp
References -
Validation pattern -
Table 268 areaId (OSPF area identifier) (Cont.)
Parameter name OSPF area stub flag
Abbreviated name areaStub
3GPP name -
Managed Object -
Multiplicity 1
Description This parameter specifies whether the OSPF area is a stub area. OSPF backbone area "0.0.0.0" cannot be stub area.
Range false (0), true (1)
Units -
Formula for getting internal value
• false => 0 • true => 1
Default value false (0)
Default value notes -
Related functions -
Modification On-Line
Related parameters -
Table 269 areaStub (OSPF area stub flag)
340 DN70577885
Flexi Transport Module Parameters
Id:0900d80580975ffbConfidential
OSPFV2 Parameters
32.5 ospfEnabled (OSPF enabling flag)
Parameter relationships -
Related options • RAN1879 Dynamic routing by OSPF
Feature dependencies -
Interfaces • EM <-> FTM • RAC <-> FTM • RAC <-> RACApp
References -
Validation pattern -
Table 269 areaStub (OSPF area stub flag) (Cont.)
Parameter name OSPF enabling flag
Abbreviated name ospfEnabled
3GPP name -
Managed Object OSPFV2
Multiplicity 1
Description If set to true, this parameter enables OSPF.
Note: OSPF is not supported on the following modules:
FTEB, FTHA, FTPB, FTFA.
Range false (0), true (1)
Units -
Formula for getting internal value
• false => 0 • true => 1
Default value false (0)
Default value notes -
Related functions -
Modification On-Line
Related parameters unitTypeExpected of UNIT - OSPF is not supported on the following modules:
Parameter relationships -
Related options • RAN1879 Dynamic routing by OSPF
Feature dependencies -
Table 270 ospfEnabled (OSPF enabling flag)
DN70577885 341
Flexi Transport Module Parameters OSPFV2 Parameters
Id:0900d80580975ffbConfidential
32.6 ospfRouterId (OSPF router identification)
Interfaces • EM <-> FTM • RAC <-> FTM • RAC <-> RACApp
References -
Validation pattern -
Table 270 ospfEnabled (OSPF enabling flag) (Cont.)
Parameter name OSPF router identification
Abbreviated name ospfRouterId
3GPP name -
Managed Object OSPFV2
Multiplicity 1
Description This parameter identifies the OSPF router through an IP address. If the operator sets the parameter to 0.0.0.0 the FTM will overwrite the value as follows:
- with the highest configured virtual IP address in the applications binding map of the IPNO class
- if none of the IP addresses of that map is a virtual IP address, the FTM shall overwrite the parameter with the highest network interface IP address.
NOTE: Any change to this parameter causes OSPF daemon restart. It may cause temporary connectiv-ity loss depending on routing configuration.
Range 7...15
Units characters
Formula for getting internal value
internal_value = gui_value
Default value 0.0.0.0
Default value notes Value 0.0.0.0 means "not specified".
Related functions -
Modification On-Line
Related parameters ospfEnabled of OSPFV2 - "ospfRouterId" should be overwritten if ospfEn-abled is true and areaId is 0.0.0.0.
Parameter relationships -
Related options • RAN1879 Dynamic routing by OSPF
Table 271 ospfRouterId (OSPF router identification)
342 DN70577885
Flexi Transport Module Parameters
Id:0900d80580975ffbConfidential
OSPFV2 Parameters
32.7 ospfV2Id (OSPF configuration identifier)
Feature dependencies -
Interfaces • EM <-> FTM • RAC <-> FTM • RAC <-> RACApp
References -
Validation pattern -
Table 271 ospfRouterId (OSPF router identification) (Cont.)
Parameter name OSPF configuration identifier
Abbreviated name ospfV2Id
3GPP name -
Managed Object OSPFV2
Multiplicity 1
Description This parameter identifies the OSPF configuration object. Value is always 1.
Range 1... 1
Units -
Formula for getting internal value
internal_value = gui_value
Default value -
Default value notes -
Related functions -
Modification Not modifiable
Related parameters -
Parameter relationships -
Related options -
Feature dependencies -
Interfaces • EM <-> FTM • RAC -> FTM • RAC <-> RACApp
References -
Validation pattern -
Table 272 ospfV2Id (OSPF configuration identifier)
DN70577885 343
Flexi Transport Module Parameters OSPFV2 Parameters
Id:0900d80580975ffbConfidential
32.8 refBandwidth (Reference bandwidth for OSPF cost equal to 1)
32.9 spfDelay (OSPF Shortest Path First recalculation delay)
Parameter name Reference bandwidth for OSPF cost equal to 1
Abbreviated name refBandwidth
3GPP name -
Managed Object OSPFV2
Multiplicity 1
Description This parameter specifies the bandwidth for which the OSPF cost is considered to be 1.
Range 1... 65535
Units mbps
Formula for getting internal value
internal_value = gui_value
Default value 10000
Default value notes Default is 10 GBps.
Related functions -
Modification On-Line
Related parameters -
Parameter relationships -
Related options • RAN1879 Dynamic routing by OSPF
Feature dependencies -
Interfaces • EM <-> FTM • RAC <-> FTM • RAC <-> RACApp
References -
Validation pattern -
Table 273 refBandwidth (Reference bandwidth for OSPF cost equal to 1)
Parameter name OSPF Shortest Path First recalculation delay
Abbreviated name spfDelay
3GPP name -
Managed Object OSPFV2
Multiplicity 1
Table 274 spfDelay (OSPF Shortest Path First recalculation delay)
344 DN70577885
Flexi Transport Module Parameters
Id:0900d80580975ffbConfidential
OSPFV2 Parameters
32.10 spfHoldTime (OSPF Shortest Path First hold time)
Description This parameter specifies the minimum amount of time to delay the Shortest Path First (SPF) recalcu-lation after a topology change event is received. Value is in milliseconds. Value range is from 0 mil-liseconds to 10 minutes.
Range 0... 600000
Units ms
Formula for getting internal value
internal_value = gui_value
Default value 200
Default value notes -
Related functions -
Modification On-Line
Related parameters -
Parameter relationships -
Related options • RAN1879 Dynamic routing by OSPF
Feature dependencies -
Interfaces • EM <-> FTM • RAC <-> FTM • RAC <-> RACApp
References -
Validation pattern -
Table 274 spfDelay (OSPF Shortest Path First recalculation delay) (Cont.)
Parameter name OSPF Shortest Path First hold time
Abbreviated name spfHoldTime
3GPP name -
Managed Object OSPFV2
Multiplicity 1
Description This parameter specifies the time between consec-utive Shortest Path First (SPF) calculations.
Value range is from 0 milliseconds to 10 minutes.
Range 0... 600000
Units ms
Table 275 spfHoldTime (OSPF Shortest Path First hold time)
DN70577885 345
Flexi Transport Module Parameters OSPFV2 Parameters
Id:0900d80580975ffbConfidential
32.11 spfMaxHoldTime (OSPF maximum Shortest Path First hold time)
Formula for getting internal value
internal_value = gui_value
Default value 5000
Default value notes -
Related functions -
Modification On-Line
Related parameters -
Parameter relationships -
Related options • RAN1879 Dynamic routing by OSPF
Feature dependencies -
Interfaces • EM <-> FTM • RAC <-> FTM • RAC <-> RACApp
References -
Validation pattern -
Table 275 spfHoldTime (OSPF Shortest Path First hold time) (Cont.)
Parameter name OSPF maximum Shortest Path First hold time
Abbreviated name spfMaxHoldTime
3GPP name -
Managed Object OSPFV2
Multiplicity 1
Description This parameter specifies the maximum hold time for Shortest Path First (SPF) calculations. Events which occur within the hold time of an ongoing SPF calculation will cause the overall holdtime to be increased by the value of spfHoldTime. If the overall holdtime surpasses the maximum hold time (spfMaxHoldTime) it is reset to the value of spfHold-Time.
Value is in milliseconds. Value range is from 0 mil-liseconds to 10 minutes.
Range 0... 600000
Units ms
Table 276 spfMaxHoldTime (OSPF maximum Shortest Path First hold time)
346 DN70577885
Flexi Transport Module Parameters
Id:0900d80580975ffbConfidential
OSPFV2 Parameters
Formula for getting internal value
internal_value = gui_value
Default value 80000
Default value notes -
Related functions -
Modification On-Line
Related parameters -
Parameter relationships -
Related options • RAN1879 Dynamic routing by OSPF
Feature dependencies -
Interfaces • EM <-> FTM • RAC <-> FTM • RAC <-> RACApp
References -
Validation pattern -
Table 276 spfMaxHoldTime (OSPF maximum Shortest Path First hold time) (Cont.)
DN70577885 347
Flexi Transport Module Parameters P3LP Parameters
Id:0900d80580975ffbConfidential
33 P3LP Parameters
33.1 acFieldCompressionOn (Access Control Field Compres-sion flag)
33.2 fcsFieldLength (Frame Check Sequence field size)
Parameter name Access Control Field Compression flag
Abbreviated name acFieldCompressionOn
3GPP name -
Managed Object P3LP
Multiplicity 1
Description If acFieldCompressionOn is true, the Address & Control Field (ACF) is compressed (saves 2 bytes, RFC-1661 chapter 6.6).
Range false (0), true (1)
Units -
Formula for getting internal value
• false => 0 • true => 1
Default value false (0)
Default value notes -
Related functions -
Modification On-Line
Related parameters -
Parameter relationships -
Related options • RAN1878 IP over ML-PPP on E1/T1/JT1 Inter-faces
Feature dependencies -
Interfaces • EM <-> FTM • RAC <-> FTM • RAC <-> RACApp
References -
Validation pattern -
Table 277 acFieldCompressionOn (Access Control Field Compression flag)
Parameter name Frame Check Sequence field size
Table 278 fcsFieldLength (Frame Check Sequence field size)
348 DN70577885
Flexi Transport Module Parameters
Id:0900d80580975ffbConfidential
P3LP Parameters
33.3 magicNumberOn (Magic number flag)
Abbreviated name fcsFieldLength
3GPP name -
Managed Object P3LP
Multiplicity 1
Description This parameter specificies the size of the Frame Check Sequence (FCS) field in bits (RFC 1570).
Range fcs0 (0), fcs16 (1), fcs32 (2)
Units -
Formula for getting internal value
gui ==> internal
fcs0 ==> 0
fcs16 ==> 1
fcs32 ==> 2
Default value fcs16 (1)
Default value notes -
Related functions -
Modification On-Line
Related parameters -
Parameter relationships -
Related options • RAN1878 IP over ML-PPP on E1/T1/JT1 Inter-faces
Feature dependencies -
Interfaces • EM <-> FTM • RAC <-> FTM • RAC <-> RACApp
References -
Validation pattern -
Table 278 fcsFieldLength (Frame Check Sequence field size) (Cont.)
Parameter name Magic number flag
Abbreviated name magicNumberOn
3GPP name -
Managed Object P3LP
Multiplicity 1
Table 279 magicNumberOn (Magic number flag)
DN70577885 349
Flexi Transport Module Parameters P3LP Parameters
Id:0900d80580975ffbConfidential
33.4 mruSize (Maximum Receive Unit (MRU) size)
Description A magic number provides a way to detect looped-back links and other data link layer anomalies by sending a number that is otherwise unlikely to happen (RFC-1661chapter 6.4). The attribute decides if the option is used.
Range false (0), true (1)
Units -
Formula for getting internal value
• false => 0 • true => 1
Default value false (0)
Default value notes -
Related functions -
Modification On-Line
Related parameters -
Parameter relationships -
Related options • RAN1878 IP over ML-PPP on E1/T1/JT1 Inter-faces
Feature dependencies -
Interfaces • EM <-> FTM • RAC <-> FTM • RAC <-> RACApp
References -
Validation pattern -
Table 279 magicNumberOn (Magic number flag) (Cont.)
Parameter name Maximum Receive Unit (MRU) size
Abbreviated name mruSize
3GPP name -
Managed Object P3LP
Multiplicity 1
Table 280 mruSize (Maximum Receive Unit (MRU) size)
350 DN70577885
Flexi Transport Module Parameters
Id:0900d80580975ffbConfidential
P3LP Parameters
Description This parameter specifies maximum receive unit size in octets.
A LCP MRU Configure-Request shall be sent auto-matically when a different value than the default 1500 bytes is set for parameter mruSize. Otherwise no Configure-Request shall be sent.
For IHSPA the maximum mruSize is 1600.
The BTS sends an alarm is the size of a received packet surpasses the mruSize.
Range PACKET_SIZE_1500 (1500), PACKET_SIZE_1520 (1520), PACKET_SIZE_1540 (1540), PACKET_SIZE_1560 (1560), PACKET_SIZE_1580 (1580), PACKET_SIZE_1600 (1600),
PACKET_SIZE_1604(1604), PACKET_SIZE_1620 (1620), PACKET_SIZE_1630 (1630) for WN7.0 1.0
PACKET_SIZE_1500 (1500), PACKET_SIZE_1520 (1520), PACKET_SIZE_1540 (1540), PACKET_SIZE_1560 (1560), PACKET_SIZE_1580 (1580), PACKET_SIZE_1600 (1600), PACKET_SIZE_1620 (1620), PACKET_SIZE_1630 (1630) for WN7.0 2.0
Units -
Formula for getting internal value
gui ==> internal
PACKET_SIZE_1500 ==> 1500
PACKET_SIZE_1520 ==> 1520
PACKET_SIZE_1540 ==> 1540
PACKET_SIZE_1560 ==> 1560
PACKET_SIZE_1580 ==> 1580
PACKET_SIZE_1600 ==> 1600
PACKET_SIZE_1620 ==> 1620
PACKET_SIZE_1630 ==> 1630
Default value PACKET_SIZE_1500 (1500)
Default value notes -
Related functions -
Modification On-Line
Related parameters -
Table 280 mruSize (Maximum Receive Unit (MRU) size) (Cont.)
DN70577885 351
Flexi Transport Module Parameters P3LP Parameters
Id:0900d80580975ffbConfidential
33.5 p3lpId (PPP link identifier)
Parameter relationships -
Related options • RAN1878 IP over ML-PPP on E1/T1/JT1 Inter-faces
Feature dependencies • CN4065
Interfaces • EM <-> FTM • RAC <-> FTM • RAC <-> RACApp
References -
Validation pattern -
Table 280 mruSize (Maximum Receive Unit (MRU) size) (Cont.)
Parameter name PPP link identifier
Abbreviated name p3lpId
3GPP name -
Managed Object P3LP
Multiplicity 1
Description This parameter identifies the PPP link.
The format is slot#-if#
where slot# is always 1 (slot number) and
if# = 1..16 (interface number).
Range 3...4
Units characters
Formula for getting internal value
internal_value = gui_value
Default value -
Default value notes -
Related functions -
Modification Not modifiable
Related parameters -
Parameter relationships -
Related options • RAN1878 IP over ML-PPP on E1/T1/JT1 Inter-faces
Feature dependencies -
Table 281 p3lpId (PPP link identifier)
352 DN70577885
Flexi Transport Module Parameters
Id:0900d80580975ffbConfidential
P3LP Parameters
33.6 protocolFieldCompressionOn (Protocol Field Compres-sion flag)
Interfaces • EM <-> FTM • RAC -> FTM • RAC <-> RACApp
References -
Validation pattern -
Table 281 p3lpId (PPP link identifier) (Cont.)
Parameter name Protocol Field Compression flag
Abbreviated name protocolFieldCompressionOn
3GPP name -
Managed Object P3LP
Multiplicity 1
Description The Protocol Field (PCF) in LCP packets by default has 2 octets. If the PCF option is used, it is com-pressed to 1 octet (RFC-1661 chapter 6.5). If proto-colFieldCompressionOn equals true, the option is used.
Range false (0), true (1)
Units -
Formula for getting internal value
• false => 0 • true => 1
Default value false (0)
Default value notes -
Related functions -
Modification On-Line
Related parameters -
Parameter relationships -
Related options • RAN1878 IP over ML-PPP on E1/T1/JT1 Inter-faces
Feature dependencies -
Interfaces • EM <-> FTM • RAC <-> FTM • RAC <-> RACApp
References -
Table 282 protocolFieldCompressionOn (Protocol Field Compression flag)
DN70577885 353
Flexi Transport Module Parameters P3LP Parameters
Id:0900d80580975ffbConfidential
Validation pattern -
Table 282 protocolFieldCompressionOn (Protocol Field Compression flag) (Cont.)
354 DN70577885
Flexi Transport Module Parameters
Id:0900d80580975ffbConfidential
P3ML Parameters
34 P3ML Parameters
34.1 administrativeState (Administrative state of the PPP multi-link)
34.2 endPointDiscriminatorType (Endpoint discriminator type)
Parameter name Administrative state of the PPP multi-link
Abbreviated name administrativeState
3GPP name -
Managed Object P3ML
Multiplicity 1
Description This parameter is used to lock and unlock the PPP multi-link. Locking the PPP multi-link deactivates it.
Range locked (0), unlocked (1)
Units -
Formula for getting internal value
gui ==> internal
locked ==> 0
unlocked ==> 1
Default value locked (0)
Default value notes The interface is locked.
Related functions -
Modification On-Line
Related parameters -
Parameter relationships -
Related options • RAN1878 IP over ML-PPP on E1/T1/JT1 Inter-faces
Feature dependencies -
Interfaces • EM <-> FTM • RAC <-> FTM • RAC <-> RACApp
References -
Validation pattern -
Table 283 administrativeState (Administrative state of the PPP multi-link)
Parameter name Endpoint discriminator type
Table 284 endPointDiscriminatorType (Endpoint discriminator type)
DN70577885 355
Flexi Transport Module Parameters P3ML Parameters
Id:0900d80580975ffbConfidential
34.3 interfaces (Physical interface list)
Abbreviated name endPointDiscriminatorType
3GPP name -
Managed Object P3ML
Multiplicity 1
Description The Endpoint Discriminator Option is a way to dynamically link to an existing multilink bundle of the peer or to create a new multilink bundle in the peer (RFC 1990 chapter 5.5.3). The attribute decides if the option is used.
Range NORMAL (0), EDGE (1)
Units -
Formula for getting internal value
gui ==> internal
NORMAL ==> 0
EDGE ==> 1
Default value NORMAL (0)
Default value notes -
Related functions -
Modification On-Line
Related parameters -
Parameter relationships -
Related options • RAN1878 IP over ML-PPP on E1/T1/JT1 Inter-faces
Feature dependencies -
Interfaces • EM <-> FTM • RAC <-> FTM • RAC <-> RACApp
References -
Validation pattern -
Table 284 endPointDiscriminatorType (Endpoint discriminator type) (Cont.)
Parameter name Physical interface list
Abbreviated name interfaces
3GPP name -
Managed Object P3ML
Multiplicity 16
Table 285 interfaces (Physical interface list)
356 DN70577885
Flexi Transport Module Parameters
Id:0900d80580975ffbConfidential
P3ML Parameters
34.4 mpFragmentSize (Fragment size in egress direction)
Description This parameter holds the list of the physical inter-faces used for MLPPP.
The maximum number of interfaces in one MLPPP interface depends on the unit type:
FIIB, FILB, FTIA, FTIB, FTJA, FTLB: 4
FTEB, FTPB, FTFA: 8
FTFA, FTHA, FTFB: 16
Interfaces have to be selected consecutively starting with 1.
Range 1... 16
Units -
Formula for getting internal value
internal_value = gui_value
Default value -
Default value notes -
Related functions -
Modification On-Line
Related parameters -
Parameter relationships -
Related options • RAN1878 IP over ML-PPP on E1/T1/JT1 Inter-faces
Feature dependencies -
Interfaces • EM <-> FTM • RAC <-> FTM • RAC <-> RACApp
References -
Validation pattern -
Table 285 interfaces (Physical interface list) (Cont.)
Parameter name Fragment size in egress direction
Abbreviated name mpFragmentSize
3GPP name -
Managed Object P3ML
Multiplicity 1
Table 286 mpFragmentSize (Fragment size in egress direction)
DN70577885 357
Flexi Transport Module Parameters P3ML Parameters
Id:0900d80580975ffbConfidential
34.5 mrruSize (Maximum Receive Reconstructed Unit (MRRU) size)
Description This parameter specificies the PPP MultiLink Protocol fragment size in egress direction in octets.
Range FRAGMENT_SIZE_128 (128), FRAGMENT_SIZE_256 (256), FRAGMENT_SIZE_512 (512)
Units -
Formula for getting internal value
gui ==> internal
FRAGMENT_SIZE_128 ==> 128
FRAGMENT_SIZE_256 ==> 256
FRAGMENT_SIZE_512 ==> 512
Default value FRAGMENT_SIZE_256 (256)
Default value notes -
Related functions -
Modification On-Line
Related parameters -
Parameter relationships -
Related options • RAN1878 IP over ML-PPP on E1/T1/JT1 Inter-faces
Feature dependencies -
Interfaces • EM <-> FTM • RAC <-> FTM • RAC <-> RACApp
References -
Validation pattern -
Table 286 mpFragmentSize (Fragment size in egress direction) (Cont.)
Parameter name Maximum Receive Reconstructed Unit (MRRU) size
Abbreviated name mrruSize
3GPP name -
Managed Object P3ML
Multiplicity 1
Table 287 mrruSize (Maximum Receive Reconstructed Unit (MRRU) size)
358 DN70577885
Flexi Transport Module Parameters
Id:0900d80580975ffbConfidential
P3ML Parameters
Description This parameter specifies maximum receive recon-structed unit size in octets.
The MRRU option shall always be sent as part of every LCP negotiation and applies to then to the bundle.
For IHSPA the maximum mruSize is 1600.
The BTS sends an alarm is the size of a received packet surpasses the mrruSize.
Range PACKET_SIZE_1500 (1500), PACKET_SIZE_1520 (1520), PACKET_SIZE_1540 (1540), PACKET_SIZE_1560 (1560), PACKET_SIZE_1580 (1580), PACKET_SIZE_1600 (1600), PACKET_SIZE_1620 (1620), PACKET_SIZE_1630 (1630)
Units -
Formula for getting internal value
gui ==> internal
PACKET_SIZE_1500 ==> 1500
PACKET_SIZE_1520 ==> 1520
PACKET_SIZE_1540 ==> 1540
PACKET_SIZE_1560 ==> 1560
PACKET_SIZE_1580 ==> 1580
PACKET_SIZE_1600 ==> 1600
PACKET_SIZE_1620 ==> 1620
PACKET_SIZE_1630 ==> 1630
Default value PACKET_SIZE_1500 (1500)
Default value notes -
Related functions -
Modification On-Line
Related parameters -
Parameter relationships -
Related options • RAN1878 IP over ML-PPP on E1/T1/JT1 Inter-faces
Feature dependencies -
Interfaces • EM <-> FTM • RAC <-> FTM • RAC <-> RACApp
References -
Table 287 mrruSize (Maximum Receive Reconstructed Unit (MRRU) size) (Cont.)
DN70577885 359
Flexi Transport Module Parameters P3ML Parameters
Id:0900d80580975ffbConfidential
34.6 netmask (Netmask of the IP address of the PPP endpoint)
34.7 p3mlId (PPP multi-link identifier)
Validation pattern -
Table 287 mrruSize (Maximum Receive Reconstructed Unit (MRRU) size) (Cont.)
Parameter name Netmask of the IP address of the PPP endpoint
Abbreviated name netmask
3GPP name -
Managed Object P3ML
Multiplicity 1
Description Netmask for the primary IP address of the PPP end-point. To be entered in dotted decimal format.
Range 7...15
Units characters
Formula for getting internal value
internal_value = gui_value
Default value -
Default value notes -
Related functions -
Modification On-Line
Related parameters -
Parameter relationships -
Related options • RAN1878 IP over ML-PPP on E1/T1/JT1 Inter-faces
Feature dependencies -
Interfaces • EM <-> FTM • RAC <-> FTM • RAC <-> RACApp
References -
Validation pattern -
Table 288 netmask (Netmask of the IP address of the PPP endpoint)
Parameter name PPP multi-link identifier
Abbreviated name p3mlId
Table 289 p3mlId (PPP multi-link identifier)
360 DN70577885
Flexi Transport Module Parameters
Id:0900d80580975ffbConfidential
P3ML Parameters
34.8 p3pIpAddr (PPP endpoint IP address)
3GPP name -
Managed Object P3ML
Multiplicity 1
Description This parameter identifies the unique PPP multi-link object in the BTS. Value is always 1.
Range 1... 1
Units -
Formula for getting internal value
internal_value = gui_value
Default value -
Default value notes Always 1. Only 1 PPP multi-link can exist.
Related functions -
Modification Not modifiable
Related parameters -
Parameter relationships -
Related options • RAN1878 IP over ML-PPP on E1/T1/JT1 Inter-faces
Feature dependencies -
Interfaces • EM <-> FTM • RAC -> FTM • RAC <-> RACApp
References -
Validation pattern -
Table 289 p3mlId (PPP multi-link identifier) (Cont.)
Parameter name PPP endpoint IP address
Abbreviated name p3pIpAddr
3GPP name -
Managed Object P3ML
Multiplicity 1
Description IP address of the PPP endpoint in the transport network. To be entered in dotted decimal format.
Range 7...15
Units characters
Table 290 p3pIpAddr (PPP endpoint IP address)
DN70577885 361
Flexi Transport Module Parameters P3ML Parameters
Id:0900d80580975ffbConfidential
34.9 shortSeqNrOn (Short sequence numbering flag)
Formula for getting internal value
internal_value = gui_value
Default value -
Default value notes -
Related functions -
Modification On-Line
Related parameters -
Parameter relationships -
Related options • RAN1878 IP over ML-PPP on E1/T1/JT1 Inter-faces
Feature dependencies -
Interfaces • EM <-> FTM • RAC <-> FTM • RAC <-> RACApp
References -
Validation pattern -
Table 290 p3pIpAddr (PPP endpoint IP address) (Cont.)
Parameter name Short sequence numbering flag
Abbreviated name shortSeqNrOn
3GPP name -
Managed Object P3ML
Multiplicity 1
Description This parameter specificies how packets are num-bered. The Long Sequence Number Format uses 24 bits for the fragment sequence number, the short sequence format 12 bits (RFC 1990). If short-SeqNrOn equals true, the short sequence number is used.
Range false (0), true (1)
Units -
Formula for getting internal value
• false => 0 • true => 1
Default value false (0)
Default value notes -
Table 291 shortSeqNrOn (Short sequence numbering flag)
362 DN70577885
Flexi Transport Module Parameters
Id:0900d80580975ffbConfidential
P3ML Parameters
34.10 ts16Excluded (Is timeslot TS16 excluded)
Related functions -
Modification On-Line
Related parameters -
Parameter relationships -
Related options • RAN1878 IP over ML-PPP on E1/T1/JT1 Inter-faces
Feature dependencies -
Interfaces • EM <-> FTM • RAC <-> FTM • RAC <-> RACApp
References -
Validation pattern -
Table 291 shortSeqNrOn (Short sequence numbering flag) (Cont.)
Parameter name Is timeslot TS16 excluded
Abbreviated name ts16Excluded
3GPP name -
Managed Object P3ML
Multiplicity 1
Description This parameter specifies if timeslot TS16 is used. By default all timeslots from TS1 to TS31 are used. If parameter TS16Excluded has value true, timeslots TS1..TS15 and TS17..TS31 are used.
Range false (0), true (1)
Units -
Formula for getting internal value
• false => 0 • true => 1
Default value false (0)
Default value notes By default timeslot TS16 is included for E1. All timeslots from TS1 to TS31 are used.
Related functions -
Modification On-Line
Related parameters -
Parameter relationships -
Table 292 ts16Excluded (Is timeslot TS16 excluded)
DN70577885 363
Flexi Transport Module Parameters P3ML Parameters
Id:0900d80580975ffbConfidential
Related options • RAN1878 IP over ML-PPP on E1/T1/JT1 Inter-faces
Feature dependencies -
Interfaces • EM <-> FTM • RAC <-> FTM • RAC <-> RACApp
References -
Validation pattern -
Table 292 ts16Excluded (Is timeslot TS16 excluded) (Cont.)
364 DN70577885
Flexi Transport Module Parameters
Id:0900d80580975ffbConfidential
P3SL Parameters
35 P3SL Parameters
35.1 administrativeState (Administrative state of the PPP link)
35.2 interface (Physical interface list)
Parameter name Administrative state of the PPP link
Abbreviated name administrativeState
3GPP name -
Managed Object P3SL
Multiplicity 1
Description This parameter is used to lock and unlock the PPP link. Locking the PPP link deactivates it.
Range locked (0), unlocked (1)
Units -
Formula for getting internal value
gui ==> internal
locked ==> 0
unlocked ==> 1
Default value locked (0)
Default value notes The interface is locked.
Related functions -
Modification On-Line
Related parameters -
Parameter relationships -
Related options • RAN1878 IP over ML-PPP on E1/T1/JT1 Inter-faces
Feature dependencies -
Interfaces • EM <-> FTM • RAC <-> FTM • RAC <-> RACApp
References -
Validation pattern -
Table 293 administrativeState (Administrative state of the PPP link)
Parameter name Physical interface list
Abbreviated name interface
Table 294 interface (Physical interface list)
DN70577885 365
Flexi Transport Module Parameters P3SL Parameters
Id:0900d80580975ffbConfidential
35.3 netmask (Netmask for the IP address of the PPP endpoint)
3GPP name -
Managed Object P3SL
Multiplicity 1
Description This parameter holds the physical interface id used by the PPP link over PDH.
This id is restricted by the number of interfaces present in the transport module. Only IF 1 is sup-ported for current release.
Range 1... 16
Units -
Formula for getting internal value
internal_value = gui_value
Default value -
Default value notes -
Related functions -
Modification On-Line
Related parameters -
Parameter relationships -
Related options • RAN1878 IP over ML-PPP on E1/T1/JT1 Inter-faces
Feature dependencies -
Interfaces • EM <-> FTM • RAC <-> FTM • RAC <-> RACApp
References -
Validation pattern -
Table 294 interface (Physical interface list) (Cont.)
Parameter name Netmask for the IP address of the PPP endpoint
Abbreviated name netmask
3GPP name -
Managed Object P3SL
Multiplicity 1
Description Netmask for the primary IP address of the PPP end-point. To be entered in dotted decimal format.
Table 295 netmask (Netmask for the IP address of the PPP endpoint)
366 DN70577885
Flexi Transport Module Parameters
Id:0900d80580975ffbConfidential
P3SL Parameters
35.4 p3pIpAddr (PPP endpoint IP address)
Range 7...15
Units characters
Formula for getting internal value
internal_value = gui_value
Default value -
Default value notes -
Related functions -
Modification On-Line
Related parameters -
Parameter relationships -
Related options • RAN1878 IP over ML-PPP on E1/T1/JT1 Inter-faces
Feature dependencies -
Interfaces • EM <-> FTM • RAC <-> FTM • RAC <-> RACApp
References -
Validation pattern -
Table 295 netmask (Netmask for the IP address of the PPP endpoint) (Cont.)
Parameter name PPP endpoint IP address
Abbreviated name p3pIpAddr
3GPP name -
Managed Object P3SL
Multiplicity 1
Description IP address of the PPP endpoint in the transport network. To be entered in dotted decimal format.
Range 7...15
Units characters
Formula for getting internal value
internal_value = gui_value
Default value -
Default value notes -
Related functions -
Table 296 p3pIpAddr (PPP endpoint IP address)
DN70577885 367
Flexi Transport Module Parameters P3SL Parameters
Id:0900d80580975ffbConfidential
35.5 p3slId (PPP single link object instance identifier)
Modification On-Line
Related parameters -
Parameter relationships -
Related options • RAN1878 IP over ML-PPP on E1/T1/JT1 Inter-faces
Feature dependencies -
Interfaces • EM <-> FTM • RAC <-> FTM • RAC <-> RACApp
References -
Validation pattern -
Table 296 p3pIpAddr (PPP endpoint IP address) (Cont.)
Parameter name PPP single link object instance identifier
Abbreviated name p3slId
3GPP name -
Managed Object P3SL
Multiplicity 1
Description This is the object instance identifier of the PPP single link object. The value is always 1.
Range 1... 1
Units -
Formula for getting internal value
internal_value = gui_value
Default value -
Default value notes -
Related functions -
Modification Not modifiable
Related parameters -
Parameter relationships -
Related options • RAN1878 IP over ML-PPP on E1/T1/JT1 Inter-faces
Feature dependencies -
Table 297 p3slId (PPP single link object instance identifier)
368 DN70577885
Flexi Transport Module Parameters
Id:0900d80580975ffbConfidential
P3SL Parameters
35.6 ts16Excluded (Is timeslot TS16 excluded)
Interfaces • EM <-> FTM • RAC -> FTM • RAC <-> RACApp
References -
Validation pattern -
Table 297 p3slId (PPP single link object instance identifier) (Cont.)
Parameter name Is timeslot TS16 excluded
Abbreviated name ts16Excluded
3GPP name -
Managed Object P3SL
Multiplicity 1
Description This parameter specifies if timeslot TS16 is used. By default all timeslots from TS1 to TS31 are used. If parameter TS16Excluded has value true, timeslots TS1..TS15 and TS17..TS31 are used.
Range false (0), true (1)
Units -
Formula for getting internal value
• false => 0 • true => 1
Default value false (0)
Default value notes By default timeslot TS16 is included for E1. All timeslots from TS1 to TS31 are used.
Related functions -
Modification On-Line
Related parameters -
Parameter relationships -
Related options • RAN1878 IP over ML-PPP on E1/T1/JT1 Inter-faces
Feature dependencies -
Interfaces • EM <-> FTM • RAC <-> FTM • RAC <-> RACApp
References -
Validation pattern -
Table 298 ts16Excluded (Is timeslot TS16 excluded)
DN70577885 369
Flexi Transport Module Parameters PPTT Parameters
Id:0900d80580975ffbConfidential
36 PPTT Parameters
36.1 administrativeState (Administrative State)
36.2 interfaceNumber (Interface Number)
Parameter name Administrative State
Abbreviated name administrativeState
3GPP name -
Managed Object PPTT
Multiplicity 1
Description Used to lock and unlock the interface.
Locking the interface deactivates it and all alarms and any ATM cell transfer is suppressed.
Range locked (0), unlocked (1)
Units -
Formula for getting internal value
gui ==> internal
locked ==> 0
unlocked ==> 1
Default value locked (0)
Default value notes -
Related functions -
Modification On-Line
Related parameters -
Parameter relationships -
Related options -
Feature dependencies • Physical Interfaces E1, T1, JT1
Interfaces • EM <-> FTM • RAC <-> FTM • RAC <-> RACApp
References -
Validation pattern -
Table 299 administrativeState (Administrative State)
Parameter name Interface Number
Abbreviated name interfaceNumber
Table 300 interfaceNumber (Interface Number)
370 DN70577885
Flexi Transport Module Parameters
Id:0900d80580975ffbConfidential
PPTT Parameters
36.3 pdhLbo (PDH Line Build Out)
3GPP name -
Managed Object PPTT
Multiplicity 1
Description Defines the interface location on the unit.
The number of interfaces depends on the unit type.
FTEB, FTPB, FTIF, FIIF: 1..8
FIIB, FILB, FTIA, FTIB, FTJA, FTLB: 1..4
FTFB, FTHA, FTFA: 1..16
Range 1... 16
Units -
Formula for getting internal value
internal_value = gui_value
Default value -
Default value notes -
Related functions -
Modification Not modifiable
Related parameters -
Parameter relationships -
Related options -
Feature dependencies -
Interfaces • FTM -> EM • FTM -> RAC
References -
Validation pattern -
Table 300 interfaceNumber (Interface Number) (Cont.)
Parameter name PDH Line Build Out
Abbreviated name pdhLbo
3GPP name -
Managed Object PPTT
Multiplicity 1
Table 301 pdhLbo (PDH Line Build Out)
DN70577885 371
Flexi Transport Module Parameters PPTT Parameters
Id:0900d80580975ffbConfidential
36.4 pdhLineType (PDH Line Type)
Description Specifies the attenuation for the signal from the transmitter.
All attenuation values are specified in dB at 772 kHz. This parameter is only supported on T1 inter-faces.
Range PDH_LBO_0 (1), PDH_LBO_7_5 (2), PDH_LBO_15 (3)
Units -
Formula for getting internal value
gui ==> internal
PDH_LBO_0 ==> 1
PDH_LBO_7_5 ==> 2
PDH_LBO_15 ==> 3
Default value PDH_LBO_0 (1)
Default value notes -
Related functions -
Modification On-Line
Related parameters -
Parameter relationships -
Related options -
Feature dependencies • Physical Interfaces E1, T1, JT1
Interfaces • EM <-> FTM • RAC <-> FTM • RAC <-> RACApp
References -
Validation pattern -
Table 301 pdhLbo (PDH Line Build Out) (Cont.)
Parameter name PDH Line Type
Abbreviated name pdhLineType
3GPP name -
Managed Object PPTT
Multiplicity 1
Table 302 pdhLineType (PDH Line Type)
372 DN70577885
Flexi Transport Module Parameters
Id:0900d80580975ffbConfidential
PPTT Parameters
Description Specifies the frame format of the PDH signal for a physical PDH interface of a unit.
E1 (G.704):
- DOUBLEFRAME
- MULTIFRAME
- DOUBLEFRAME UNBALANCED
- MULTIFRAME UNBALANCED
T1: EXTENDED_SUPERFRAME
JT1: EXTENDED_MULTIFRAME
NOTEs:
1) This parameter is "not modifiable" for FTIB and FTLB hardware unit.
2) For FTIB and FTLB hardware unit UNBAL-ANCED mode is not supported at all.
Range PDH_LINE_TYPE_DOUBLE_FRAME_G704 (1), PDH_LINE_TYPE_MULTI_FRAME_G704 (2), PDH_LINE_TYPE_EXTENDED_MULTIFRAME (8), PDH_LINE_TYPE_EXTENDED_SUPERFRAME (11), PDH_LINE_TYPE_DOUBLE_FRAME_G704_UNBALANCED (12), PDH_LINE_TYPE_MULTI_FRAME_G704_UNBALANCED (13)
Units -
Formula for getting internal value
gui ==> internal
PDH_LINE_TYPE_DOUBLE_FRAME_G704 ==> 1
PDH_LINE_TYPE_MULTI_FRAME_G704 ==> 2
PDH_LINE_TYPE_EXTENDED_MULTIFRAME ==> 8
PDH_LINE_TYPE_EXTENDED_SUPERFRAME ==> 11
PDH_LINE_TYPE_DOUBLE_FRAME_G704_UNBALANCED ==> 12
PDH_LINE_TYPE_MULTI_FRAME_G704_UNBALANCED ==> 13
Default value -
Table 302 pdhLineType (PDH Line Type) (Cont.)
DN70577885 373
Flexi Transport Module Parameters PPTT Parameters
Id:0900d80580975ffbConfidential
36.5 pdhPSTTPId (PDH Interface Identifier)
Default value notes Defaults depend on E1/T1/JT1:E1: PDH_LINE_TYPE_MULTI_FRAME_G704T1: PDH_LINE_TYPE_EXTENDED_SUPERFRAMEJT1: PDH_LINE_TYPE_EXTENDED_MULTIFRAME
Related functions -
Modification On-Line
Related parameters -
Parameter relationships When setting the PDH Line Type to another inter-face type (E1/T1/JT1), FTM switches on all inter-faces of this unit the PDH Line Type to the default value for that interface type. In the second configu-ration step the framing format within this interface type can be modified.
Notes
1) In case of switching the line type, all ATM, IMA and CES objects that are associated with this unit are deleted!
2) PdhLineType is not modifiable for the FTIB and the FTLB hardware unit. It must be set on creation of the object instance.
3) UNBALANCED mode is not supported at all for the FTIB and FTLB hardware unit.
Related options -
Feature dependencies • Physical Interfaces E1, T1, JT1
Interfaces • EM <-> FTM • RAC <-> FTM • RAC <-> RACApp
References -
Validation pattern -
Table 302 pdhLineType (PDH Line Type) (Cont.)
Parameter name PDH Interface Identifier
Abbreviated name pdhPSTTPId
3GPP name -
Managed Object PPTT
Multiplicity 1
Table 303 pdhPSTTPId (PDH Interface Identifier)
374 DN70577885
Flexi Transport Module Parameters
Id:0900d80580975ffbConfidential
PPTT Parameters
Description This parameter identifies a PDH interface.
Format: unit#-if#
where
unit# = slot number of the unit containing the PDH interfaces, and
if# = the interface number of the physical interface on the unit
and
for FIIB/FILB/FTIA/FTIB/FTJA/FTLB,
unit#: 1 : This is always 1, since there is only 1 slot.
if#: 1..4
for FTFB/FTHA/FTFA,
unit#: 1 : This is always 1, since there is only 1 slot.
if#: 1..16
for FTEB/FTPB/FTIF/FIIF,
unit#: 1 : The slot number is '1', since this is an additional unit
if#: 1..8 : Value range is 1..8 for IF1..IF8 on this unit
Range 3...4
Units characters
Formula for getting internal value
internal_value = gui_value
Default value -
Default value notes -
Related functions -
Modification Not modifiable
Related parameters -
Parameter relationships -
Related options -
Feature dependencies -
Interfaces • EM <-> FTM • RAC -> FTM • RAC <-> RACApp
References -
Validation pattern -
Table 303 pdhPSTTPId (PDH Interface Identifier) (Cont.)
DN70577885 375
Flexi Transport Module Parameters PPTT Parameters
Id:0900d80580975ffbConfidential
36.6 unitNumber (Unit Number)
Parameter name Unit Number
Abbreviated name unitNumber
3GPP name -
Managed Object PPTT
Multiplicity 1
Description Specifies the location of the unit providing the PDH interface. In this release it is always 1.
Range 1... 1
Units -
Formula for getting internal value
internal_value = gui_value
Default value -
Default value notes -
Related functions -
Modification Not modifiable
Related parameters -
Parameter relationships -
Related options -
Feature dependencies -
Interfaces • FTM -> EM • FTM -> RAC
References -
Validation pattern -
Table 304 unitNumber (Unit Number)
376 DN70577885
Flexi Transport Module Parameters
Id:0900d80580975ffbConfidential
PWMP Parameters
37 PWMP Parameters
37.1 bfdAdminUp (BFD actual session administration flag)
37.2 bfdEnable (Bidirectional Forwarding Enabled)
Parameter name BFD actual session administration flag
Abbreviated name bfdAdminUp
3GPP name -
Managed Object PWMP
Multiplicity 1
Description This parameter is used to switch on or off the actual BFD session.
Note that this parameter is only relevant if parame-ter bfdEnable has value true.
Range false (0), true (1)
Units -
Formula for getting internal value
• false => 0 • true => 1
Default value true (1)
Default value notes -
Related functions -
Modification On-Line
Related parameters bfdEnable of PWMP
Parameter relationships bfdAdminUp is only relevant if bfdEnable has value true.
Related options -
Feature dependencies • RAN1142 ATM over Ethernet for BTS
Interfaces • EM <-> FTM • RAC <-> FTM • RAC <-> RACApp
References -
Validation pattern -
Table 305 bfdAdminUp (BFD actual session administration flag)
Parameter name Bidirectional Forwarding Enabled
Table 306 bfdEnable (Bidirectional Forwarding Enabled)
DN70577885 377
Flexi Transport Module Parameters PWMP Parameters
Id:0900d80580975ffbConfidential
37.3 cellsConcatUl (Uplink Concatenation Factor.)
Abbreviated name bfdEnable
3GPP name -
Managed Object PWMP
Multiplicity 1
Description This parameter switches the BFD session on or off for each PW. BFD comprises VCCV-BFD (== PW OAM)and VCCV = Virtual Channel Continuity Veri-fication.
Range false (0), true (1)
Units -
Formula for getting internal value
• false => 0 • true => 1
Default value false (0)
Default value notes -
Related functions -
Modification On-Line
Related parameters -
Parameter relationships -
Related options -
Feature dependencies • RAN1142 ATM over Ethernet for BTS
Interfaces • EM <-> FTM • RAC <-> FTM • RAC <-> RACApp
References -
Validation pattern -
Table 306 bfdEnable (Bidirectional Forwarding Enabled) (Cont.)
Parameter name Uplink Concatenation Factor.
Abbreviated name cellsConcatUl
3GPP name -
Managed Object PWMP
Multiplicity 1
Description Uplink Concatenation Factor.
Range 1... 28
Table 307 cellsConcatUl (Uplink Concatenation Factor.)
378 DN70577885
Flexi Transport Module Parameters
Id:0900d80580975ffbConfidential
PWMP Parameters
37.4 ctpList (Set of registered vcCTPs.)
Units -
Formula for getting internal value
internal_value = gui_value
Default value 28
Default value notes -
Related functions -
Modification On-Line
Related parameters -
Parameter relationships -
Related options -
Feature dependencies • RAN1142 ATM over Ethernet for BTS
Interfaces • EM <-> FTM • RAC <-> FTM • RAC <-> RACApp
References -
Validation pattern -
Table 307 cellsConcatUl (Uplink Concatenation Factor.) (Cont.)
Parameter name Set of registered vcCTPs.
Abbreviated name ctpList
3GPP name -
Managed Object PWMP
Multiplicity 100
Description Set of registered vcCTPs.
Represented as Local MOId strings of VCCT without the prefix "DN:"
Example: "VPTT-1-76-2/VCCT-32"
Range 10...32
Units characters
Formula for getting internal value
internal_value = gui_value
Default value -
Default value notes -
Related functions -
Table 308 ctpList (Set of registered vcCTPs.)
DN70577885 379
Flexi Transport Module Parameters PWMP Parameters
Id:0900d80580975ffbConfidential
37.5 labelDl (Downlink MPLS Header)
Modification On-Line
Related parameters -
Parameter relationships -
Related options -
Feature dependencies • RAN1142 ATM over Ethernet for BTS
Interfaces • EM <-> FTM • RAC <-> FTM • RAC <-> RACApp
References -
Validation pattern -
Table 308 ctpList (Set of registered vcCTPs.) (Cont.)
Parameter name Downlink MPLS Header
Abbreviated name labelDl
3GPP name -
Managed Object PWMP
Multiplicity 1
Description Downlink MPLS Header (inner label)
Range 16... 1048575
Units -
Formula for getting internal value
internal_value = gui_value
Default value -
Default value notes -
Related functions -
Modification On-Line
Related parameters -
Parameter relationships -
Related options -
Feature dependencies • RAN1142 ATM over Ethernet for BTS
Interfaces • EM <-> FTM • RAC <-> FTM • RAC <-> RACApp
References -
Table 309 labelDl (Downlink MPLS Header)
380 DN70577885
Flexi Transport Module Parameters
Id:0900d80580975ffbConfidential
PWMP Parameters
37.6 labelUl (Uplink MPLS Header)
37.7 perHopBehaviour (Per hop behaviour DiffServ)
Validation pattern -
Table 309 labelDl (Downlink MPLS Header) (Cont.)
Parameter name Uplink MPLS Header
Abbreviated name labelUl
3GPP name -
Managed Object PWMP
Multiplicity 1
Description Uplink MPLS Header (inner label)
Range 16... 1048575
Units -
Formula for getting internal value
internal_value = gui_value
Default value -
Default value notes -
Related functions -
Modification On-Line
Related parameters -
Parameter relationships -
Related options -
Feature dependencies • RAN1142 ATM over Ethernet for BTS
Interfaces • EM <-> FTM • RAC <-> FTM • RAC <-> RACApp
References -
Validation pattern -
Table 310 labelUl (Uplink MPLS Header)
Parameter name Per hop behaviour DiffServ
Abbreviated name perHopBehaviour
3GPP name -
Managed Object PWMP
Table 311 perHopBehaviour (Per hop behaviour DiffServ)
DN70577885 381
Flexi Transport Module Parameters PWMP Parameters
Id:0900d80580975ffbConfidential
Multiplicity 1
Description Per hop behaviour (DiffServ). This parameter is used to determine the DSCP value(Diff Serv Code Point) that must be stored in the first 6 bits of the 'Type of Service' (ToS) field that is part of the standard IP header. The DSCP for the given per-HopBehaviour is configured in the trafficTypesMap of the QOS object.
Range expeditedForwarding (0), assuredForwardingClass4 (1), assuredForwardingClass3 (2), assuredForwardingClass2 (3), assuredForwardingClass1 (4), bestEffort (5)
Units -
Formula for getting internal value
gui ==> internal
expeditedForwarding ==> 0
assuredForwardingClass4 ==> 1
assuredForwardingClass3 ==> 2
assuredForwardingClass2 ==> 3
assuredForwardingClass1 ==> 4
bestEffort ==> 5
Default value bestEffort (5)
Default value notes -
Related functions -
Modification On-Line
Related parameters trafficTypesMap of QOS
Parameter relationships perHopBehaviour is used as a search criterium in the trafficTypesMap to find the corresponding DSCP value.
Related options -
Feature dependencies • RAN1142 ATM over Ethernet for BTS
Interfaces • EM <-> FTM • RAC <-> FTM • RAC <-> RACApp
References -
Validation pattern -
Table 311 perHopBehaviour (Per hop behaviour DiffServ) (Cont.)
382 DN70577885
Flexi Transport Module Parameters
Id:0900d80580975ffbConfidential
PWMP Parameters
37.8 pkTimer (Packetization Timer)
Parameter name Packetization Timer
Abbreviated name pkTimer
3GPP name -
Managed Object PWMP
Multiplicity 1
Description This parameter shall define for each PW the maximum time allowed to create a PW frame. Value range is [500, 5000] µs, possible values are 500, 1000, 2000, 3000, 4000 and 5000 µs.
Please note that small deviations between actual and nominal values exist in the implementation. These must be taken into account by the planning tools.
Range 500 (500), 1000 (1000), 2000 (2000), 3000 (3000), 4000 (4000), 5000 (5000)
Units -
Formula for getting internal value
gui ==> internal
500 ==> 500
1000 ==> 1000
2000 ==> 2000
3000 ==> 3000
4000 ==> 4000
5000 ==> 5000
Default value 500 (500)
Default value notes -
Related functions -
Modification On-Line
Related parameters -
Parameter relationships -
Related options -
Feature dependencies • RAN1142 ATM over Ethernet for BTS
Interfaces • EM <-> FTM • RAC <-> FTM • RAC <-> RACApp
References -
Validation pattern -
Table 312 pkTimer (Packetization Timer)
DN70577885 383
Flexi Transport Module Parameters PWMP Parameters
Id:0900d80580975ffbConfidential
37.9 pwMplsId (MPLS Pseudowire Identifier)
Parameter name MPLS Pseudowire Identifier
Abbreviated name pwMplsId
3GPP name -
Managed Object PWMP
Multiplicity 1
Description Identifies the MPLS Pseudowire. Format: slot#-mp# where
slot# = 1
mp# = 1..6
Range 3
Units characters
Formula for getting internal value
internal_value = gui_value
Default value -
Default value notes -
Related functions -
Modification Not modifiable
Related parameters -
Parameter relationships -
Related options -
Feature dependencies • RAN1142 ATM over Ethernet for BTS
Interfaces • EM <-> FTM • RAC -> FTM • RAC <-> RACApp
References -
Validation pattern -
Table 313 pwMplsId (MPLS Pseudowire Identifier)
384 DN70577885
Flexi Transport Module Parameters
Id:0900d80580975ffbConfidential
PWNE Parameters
38 PWNE Parameters
38.1 bfdTimer (BFD Timer)
38.2 bfdDetectMult (Maximum allowed number of lost control packets for BFD)
Parameter name BFD Timer
Abbreviated name bfdTimer
3GPP name -
Managed Object PWNE
Multiplicity 1
Description Timing details for VCCV-BFD. (i.e. PW OAM)
Only one value set must be defined
Formula for getting internal value
-
Default value -
Default value notes -
Related functions -
Child parameters • bfdDetectMult • desiredMinTxIntvl • requiredMinRxIntvl
Modification On-Line
Related parameters -
Parameter relationships -
Related options -
Feature dependencies • RAN1142 ATM over Ethernet for BTS
Interfaces • EM <-> FTM • RAC <-> FTM • RAC <-> RACApp
References -
Validation pattern -
Table 314 bfdTimer (BFD Timer)
Parameter name Maximum allowed number of lost control packets for BFD
Table 315 bfdDetectMult (Maximum allowed number of lost control packets for BFD)
DN70577885 385
Flexi Transport Module Parameters PWNE Parameters
Id:0900d80580975ffbConfidential
38.3 desiredMinTxIntvl (Desired Minimum Transmit Interval)
Abbreviated name bfdDetectMult
3GPP name -
Managed Object -
Multiplicity 1
Description This parameter holds the number of control packets that the BTS may lose before the BFD session is declared down.
Range 2... 10
Units -
Formula for getting internal value
internal_value = gui_value
Default value 5
Default value notes -
Related functions -
Modification On-Line
Related parameters -
Parameter relationships -
Related options -
Feature dependencies • RAN1142 ATM over Ethernet for BTS
Interfaces • EM <-> FTM • RAC <-> FTM • RAC <-> RACApp
References -
Validation pattern -
Table 315 bfdDetectMult (Maximum allowed number of lost control packets for BFD)
Parameter name Desired Minimum Transmit Interval
Abbreviated name desiredMinTxIntvl
3GPP name -
Managed Object -
Multiplicity 1
Description Desired minimum transmit interval for the control word in ms.
Range 500... 5000
Table 316 desiredMinTxIntvl (Desired Minimum Transmit Interval)
386 DN70577885
Flexi Transport Module Parameters
Id:0900d80580975ffbConfidential
PWNE Parameters
38.4 requiredMinRxIntvl (Required Minimum Receive Interval)
Units -
Formula for getting internal value
internal_value = gui_value
Default value 500
Default value notes -
Related functions -
Modification On-Line
Related parameters -
Parameter relationships -
Related options -
Feature dependencies • RAN1142 ATM over Ethernet for BTS
Interfaces • EM <-> FTM • RAC <-> FTM • RAC <-> RACApp
References -
Validation pattern -
Table 316 desiredMinTxIntvl (Desired Minimum Transmit Interval) (Cont.)
Parameter name Required Minimum Receive Interval
Abbreviated name requiredMinRxIntvl
3GPP name -
Managed Object -
Multiplicity 1
Description Required minimum receive interval for the control word in ms.
Range 500... 5000
Units -
Formula for getting internal value
internal_value = gui_value
Default value 500
Default value notes -
Related functions -
Modification On-Line
Related parameters -
Table 317 requiredMinRxIntvl (Required Minimum Receive Interval)
DN70577885 387
Flexi Transport Module Parameters PWNE Parameters
Id:0900d80580975ffbConfidential
38.5 cwEnable (Control Word Enable)
Parameter relationships -
Related options -
Feature dependencies • RAN1142 ATM over Ethernet for BTS
Interfaces • EM <-> FTM • RAC <-> FTM • RAC <-> RACApp
References -
Validation pattern -
Table 317 requiredMinRxIntvl (Required Minimum Receive Interval) (Cont.)
Parameter name Control Word Enable
Abbreviated name cwEnable
3GPP name -
Managed Object PWNE
Multiplicity 1
Description Enables the setting of the Control Word bits in the data packet.
Range false (0), true (1)
Units -
Formula for getting internal value
• false => 0 • true => 1
Default value false (0)
Default value notes -
Related functions -
Modification On-Line
Related parameters -
Parameter relationships -
Related options -
Feature dependencies • RAN1142 ATM over Ethernet for BTS
Interfaces • EM <-> FTM • RAC <-> FTM • RAC <-> RACApp
References -
Validation pattern -
Table 318 cwEnable (Control Word Enable)
388 DN70577885
Flexi Transport Module Parameters
Id:0900d80580975ffbConfidential
PWNE Parameters
38.6 pwNeId (Pseudowire Network Element Identifier)
Parameter name Pseudowire Network Element Identifier
Abbreviated name pwNeId
3GPP name -
Managed Object PWNE
Multiplicity 1
Description There is alway only one instance of this class. It is identified with 1
Range 1
Units characters
Formula for getting internal value
internal_value = gui_value
Default value -
Default value notes -
Related functions -
Modification Not modifiable
Related parameters -
Parameter relationships -
Related options -
Feature dependencies • RAN1142 ATM over Ethernet for BTS
Interfaces • EM <-> FTM • RAC -> FTM • RAC <-> RACApp
References -
Validation pattern -
Table 319 pwNeId (Pseudowire Network Element Identifier)
DN70577885 389
Flexi Transport Module Parameters PWTIP Parameters
Id:0900d80580975ffbConfidential
39 PWTIP Parameters
39.1 administrativeState (Administrative State)
39.2 attachedPWList (Attached Pseudo-Wires List)
Parameter name Administrative State
Abbreviated name administrativeState
3GPP name -
Managed Object PWTIP
Multiplicity 1
Description Used to lock and unlock the interface.
Locking the interface deactivates it and all alarms and any ATM cell transfer is suppressed.
Range locked (0), unlocked (1)
Units -
Formula for getting internal value
gui ==> internal
locked ==> 0
unlocked ==> 1
Default value locked (0)
Default value notes -
Related functions -
Modification On-Line
Related parameters -
Parameter relationships -
Related options -
Feature dependencies • RAN1142 ATM over Ethernet for BTS
Interfaces • EM <-> FTM • RAC <-> FTM • RAC <-> RACApp
References -
Validation pattern -
Table 320 administrativeState (Administrative State)
Parameter name Attached Pseudo-Wires List
Abbreviated name attachedPWList
Table 321 attachedPWList (Attached Pseudo-Wires List)
390 DN70577885
Flexi Transport Module Parameters
Id:0900d80580975ffbConfidential
PWTIP Parameters
39.3 pwTipId (Pseudowire Tunnel IP Identifier)
3GPP name -
Managed Object PWTIP
Multiplicity 6
Description A list of all Pseudowires running through this tunnel.
Format: slot#-mp#, e.g. "1-5" with
slot#: always "1" in this release
mp#: 1..6
Range 3
Units characters
Formula for getting internal value
internal_value = gui_value
Default value -
Default value notes -
Related functions -
Modification On-Line
Related parameters -
Parameter relationships -
Related options -
Feature dependencies • RAN1142 ATM over Ethernet for BTS
Interfaces • EM <-> FTM • RAC <-> FTM • RAC <-> RACApp
References -
Validation pattern -
Table 321 attachedPWList (Attached Pseudo-Wires List) (Cont.)
Parameter name Pseudowire Tunnel IP Identifier
Abbreviated name pwTipId
3GPP name -
Managed Object PWTIP
Multiplicity 1
Description Identifier for the Pseudowire Tunnel.
The value is fixed to 1-76.
Range 4
Table 322 pwTipId (Pseudowire Tunnel IP Identifier)
DN70577885 391
Flexi Transport Module Parameters PWTIP Parameters
Id:0900d80580975ffbConfidential
39.4 remoteIpv4Addr (Remote IPv4 Address)
Units characters
Formula for getting internal value
internal_value = gui_value
Default value -
Default value notes -
Related functions -
Modification Not modifiable
Related parameters -
Parameter relationships -
Related options -
Feature dependencies • RAN1142 ATM over Ethernet for BTS
Interfaces • EM <-> FTM • RAC -> FTM • RAC <-> RACApp
References -
Validation pattern -
Table 322 pwTipId (Pseudowire Tunnel IP Identifier) (Cont.)
Parameter name Remote IPv4 Address
Abbreviated name remoteIpv4Addr
3GPP name -
Managed Object PWTIP
Multiplicity 1
Description This parameter shall define the IPv4 address of the remote PWE3 GW (RNC GW) where the PW is ter-minated. The address will range from 0.0.0.0 (7 characters) to 255.255.255.255 (15 characters)
Range 7...15
Units characters
Formula for getting internal value
internal_value = gui_value
Default value -
Default value notes -
Related functions -
Modification On-Line
Table 323 remoteIpv4Addr (Remote IPv4 Address)
392 DN70577885
Flexi Transport Module Parameters
Id:0900d80580975ffbConfidential
PWTIP Parameters
Related parameters -
Parameter relationships -
Related options -
Feature dependencies • RAN1142 ATM over Ethernet for BTS
Interfaces • EM <-> FTM • RAC <-> FTM • RAC <-> RACApp
References -
Validation pattern -
Table 323 remoteIpv4Addr (Remote IPv4 Address) (Cont.)
DN70577885 393
Flexi Transport Module Parameters QOS Parameters
Id:0900d80580975ffbConfidential
40 QOS Parameters
40.1 perHopBehaviourWeightList (Per Hop Behaviour Weight List)
Parameter name Per Hop Behaviour Weight List
Abbreviated name perHopBehaviourWeightList
3GPP name -
Managed Object QOS
Multiplicity 1
Description This is a set of 5 weight values for the traffic queues associated to the Per Hop Behaviours:
- Assured Forwarding 4 (AF4)
- Assured Forwarding 3 (AF3)
- Assured Forwarding 2 (AF2)
- Assured Forwarding 1 (AF1)
- Best Effort (BE.
Weight value range is between 1 and 10.000.
Formula for getting internal value
-
Default value -
Default value notes -
Related functions -
Child parameters • assuredForwardingClass1 • assuredForwardingClass2 • assuredForwardingClass3 • assuredForwardingClass4 • bestEffort
Modification On-Line
Related parameters -
Parameter relationships -
Related options • RAN1253 Iub Transport QoS
Feature dependencies -
Interfaces • EM <-> FTM • RAC <-> FTM • RAC <-> RACApp
References -
Table 324 perHopBehaviourWeightList (Per Hop Behaviour Weight List)
394 DN70577885
Flexi Transport Module Parameters
Id:0900d80580975ffbConfidential
QOS Parameters
40.2 assuredForwardingClass1 (Assured Forwarding Class 1 Weight Value)
Validation pattern -
Table 324 perHopBehaviourWeightList (Per Hop Behaviour Weight List) (Cont.)
Parameter name Assured Forwarding Class 1 Weight Value
Abbreviated name assuredForwardingClass1
3GPP name -
Managed Object -
Multiplicity 1
Description This is the weight value of the traffic queue associ-ated to the Per Hop Behaviour Assured Forwarding Class 1 (AF1).
Range 1... 10000
Units -
Formula for getting internal value
internal_value = gui_value
Default value 10
Default value notes -
Related functions -
Modification On-Line
Related parameters -
Parameter relationships -
Related options • RAN1253 Iub Transport QoS
Feature dependencies -
Interfaces • EM <-> FTM • RAC <-> FTM • RAC <-> RACApp
References -
Validation pattern -
Table 325 assuredForwardingClass1 (Assured Forwarding Class 1 Weight Value)
DN70577885 395
Flexi Transport Module Parameters QOS Parameters
Id:0900d80580975ffbConfidential
40.3 assuredForwardingClass2 (Assured Forwarding Class 2 Weight Value)
40.4 assuredForwardingClass3 (Assured Forwarding Class 3 Weight Value)
Parameter name Assured Forwarding Class 2 Weight Value
Abbreviated name assuredForwardingClass2
3GPP name -
Managed Object -
Multiplicity 1
Description This is the weight value of the traffic queue associ-ated to the Per Hop Behaviour Assured Forwarding Class 2 (AF2).
Range 1... 10000
Units -
Formula for getting internal value
internal_value = gui_value
Default value 100
Default value notes -
Related functions -
Modification On-Line
Related parameters -
Parameter relationships -
Related options • RAN1253 Iub Transport QoS
Feature dependencies -
Interfaces • EM <-> FTM • RAC <-> FTM • RAC <-> RACApp
References -
Validation pattern -
Table 326 assuredForwardingClass2 (Assured Forwarding Class 2 Weight Value)
Parameter name Assured Forwarding Class 3 Weight Value
Abbreviated name assuredForwardingClass3
3GPP name -
Managed Object -
Table 327 assuredForwardingClass3 (Assured Forwarding Class 3 Weight Value)
396 DN70577885
Flexi Transport Module Parameters
Id:0900d80580975ffbConfidential
QOS Parameters
40.5 assuredForwardingClass4 (Assured Forwarding Class 4 Weight Value)
Multiplicity 1
Description This is the weight value of the traffic queue associ-ated to the Per Hop Behaviour Assured Forwarding Class 3 (AF3).
Range 1... 10000
Units -
Formula for getting internal value
internal_value = gui_value
Default value 1000
Default value notes -
Related functions -
Modification On-Line
Related parameters -
Parameter relationships -
Related options • RAN1253 Iub Transport QoS
Feature dependencies -
Interfaces • EM <-> FTM • RAC <-> FTM • RAC <-> RACApp
References -
Validation pattern -
Table 327 assuredForwardingClass3 (Assured Forwarding Class 3 Weight Value)
Parameter name Assured Forwarding Class 4 Weight Value
Abbreviated name assuredForwardingClass4
3GPP name -
Managed Object -
Multiplicity 1
Description This is the weight value of the traffic queue associ-ated to the Per Hop Behaviour Assured Forwarding Class 4 (AF4).
Range 1... 10000
Units -
Table 328 assuredForwardingClass4 (Assured Forwarding Class 4 Weight Value)
DN70577885 397
Flexi Transport Module Parameters QOS Parameters
Id:0900d80580975ffbConfidential
40.6 bestEffort (Best Effort Weight Value)
Formula for getting internal value
internal_value = gui_value
Default value 10000
Default value notes -
Related functions -
Modification On-Line
Related parameters -
Parameter relationships -
Related options • RAN1253 Iub Transport QoS
Feature dependencies -
Interfaces • EM <-> FTM • RAC <-> FTM • RAC <-> RACApp
References -
Validation pattern -
Table 328 assuredForwardingClass4 (Assured Forwarding Class 4 Weight Value)
Parameter name Best Effort Weight Value
Abbreviated name bestEffort
3GPP name -
Managed Object -
Multiplicity 1
Description This is the weight value of the traffic queue associ-ated to the Per Hop Behaviour Best Effort (BE).
Range 1... 10000
Units -
Formula for getting internal value
internal_value = gui_value
Default value 1
Default value notes -
Related functions -
Modification On-Line
Related parameters -
Parameter relationships -
Table 329 bestEffort (Best Effort Weight Value)
398 DN70577885
Flexi Transport Module Parameters
Id:0900d80580975ffbConfidential
QOS Parameters
40.7 qosId (Quality of Service Configuration Identifier)
Related options • RAN1253 Iub Transport QoS
Feature dependencies -
Interfaces • EM <-> FTM • RAC <-> FTM • RAC <-> RACApp
References -
Validation pattern -
Table 329 bestEffort (Best Effort Weight Value) (Cont.)
Parameter name Quality of Service Configuration Identifier
Abbreviated name qosId
3GPP name -
Managed Object QOS
Multiplicity 1
Description This parameter identifies the BTS transport Quality of Service (QOS) configuration. The value is always 1.
Range 1... 1
Units -
Formula for getting internal value
internal_value = gui_value
Default value -
Default value notes -
Related functions -
Modification Not modifiable
Related parameters -
Parameter relationships -
Related options • RAN1253 Iub Transport QoS
Feature dependencies -
Interfaces • EM <-> FTM • RAC -> FTM • RAC <-> RACApp
References -
Validation pattern -
Table 330 qosId (Quality of Service Configuration Identifier)
DN70577885 399
Flexi Transport Module Parameters QOS Parameters
Id:0900d80580975ffbConfidential
40.8 trafficTypesMap (Quality of Service mapping table)
40.9 dscpList (Differentiated Services Code Point list)
Parameter name Quality of Service mapping table
Abbreviated name trafficTypesMap
3GPP name -
Managed Object QOS
Multiplicity 35
Description This table maps traffic types to Per Hop Behaviours and to other quality of service properties, including VlanId, VlanPrio and DSCP values.
Formula for getting internal value
-
Default value -
Default value notes -
Related functions -
Child parameters • dscpList • pHB • trafficType • vlanPrio
Modification On-Line
Related parameters -
Parameter relationships -
Related options • RAN1253 Iub Transport QoS • RAN2440 Fast IP Rerouting
Feature dependencies • RAN1142 ATM over Ethernet for BTS
Interfaces • EM <-> FTM • RAC <-> FTM • RAC <-> RACApp
References -
Validation pattern -
Table 331 trafficTypesMap (Quality of Service mapping table)
Parameter name Differentiated Services Code Point list
Abbreviated name dscpList
3GPP name -
Table 332 dscpList (Differentiated Services Code Point list)
400 DN70577885
Flexi Transport Module Parameters
Id:0900d80580975ffbConfidential
QOS Parameters
40.10 pHB (Per Hop Behaviour)
Managed Object -
Multiplicity 1
Description This is the list of Differentiated Services Code Point (DSCP) values that relate to a specific traffic cate-gory. The list is a comma-seperated value list. The values are DSCP decimal values. The list can contain up to 64 entries.
Range 0...255
Units characters
Formula for getting internal value
internal_value = gui_value
Default value -
Default value notes -
Related functions -
Modification On-Line
Related parameters -
Parameter relationships -
Related options -
Feature dependencies -
Interfaces • EM <-> FTM • RAC <-> FTM • RAC <-> RACApp
References -
Validation pattern -
Table 332 dscpList (Differentiated Services Code Point list) (Cont.)
Parameter name Per Hop Behaviour
Abbreviated name pHB
3GPP name -
Managed Object -
Multiplicity 1
Table 333 pHB (Per Hop Behaviour)
DN70577885 401
Flexi Transport Module Parameters QOS Parameters
Id:0900d80580975ffbConfidential
Description This parameter designates a Per Hop Behaviour.
The following values are predefined:
0 = EF (meaning: Expedited Forwarding)
1 = AF4 (Assured Forwarding 4)
2 = AF3 (Assured Forwarding 3)
3 = AF2 (Assured Forwarding 2)
4 = AF1 (Assured Forwarding 1)
5 = BE (Best Effort).
Range expeditedForwarding (0), assuredForwardingClass4 (1), assuredForwardingClass3 (2), assuredForwardingClass2 (3), assuredForwardingClass1 (4), bestEffort (5)
Units -
Formula for getting internal value
gui ==> internal
expeditedForwarding ==> 0
assuredForwardingClass4 ==> 1
assuredForwardingClass3 ==> 2
assuredForwardingClass2 ==> 3
assuredForwardingClass1 ==> 4
bestEffort ==> 5
Default value -
Default value notes -
Related functions -
Modification On-Line
Related parameters -
Parameter relationships -
Related options -
Feature dependencies -
Interfaces • EM <-> FTM • RAC <-> FTM • RAC <-> RACApp
References -
Validation pattern -
Table 333 pHB (Per Hop Behaviour) (Cont.)
402 DN70577885
Flexi Transport Module Parameters
Id:0900d80580975ffbConfidential
QOS Parameters
40.11 trafficType (Traffic type)
Parameter name Traffic type
Abbreviated name trafficType
3GPP name -
Managed Object -
Multiplicity 1
Table 334 trafficType (Traffic type)
DN70577885 403
Flexi Transport Module Parameters QOS Parameters
Id:0900d80580975ffbConfidential
Description This parameter designates a traffic type.
Values for transport mode AtmOverEthernet:
"TOP"
"SG1" - Pseudowire (PW) for perHopBehaviour (pHB) EF
"SG2" - PW for pHB AF4
"SG3" - PW for pHB AF3
"SG4" - PW for pHB AF2
"SG5" - PW for pHB AF1
"SG6" - PW for pHB BE
"ICMP"
Values for transport mode Iub IP:
"DCN"
"NBAP"
"TOP"
"SG1" - Signalled traffic for pHB EF
"SG2" - Signalled traffic for pHB AF4
"SG3" - Signalled traffic for pHB AF3
"SG4" - Signalled traffic for pHB AF2
"SG5" - Signalled traffic for pHB AF1
"SG6" - Signalled traffic for pHB BE
"ICMP"
"CES1" to "CES4" - For mapping DSCP values to vlanPrio bits (on FIIB,FILB,FTIB,FTLB units only)
"CES1" to "CES8" - For mapping DSCP values to vlanPrio bits (on FTFB, FIIF, FTIF unit only)
"BFD1" to "BFD16"
"OSPF" (on FIIB,FILB,FTIA,FTIB,FTJA,FTLB,FTFB, FSM, FSI, FIIF, FTIF units only)
Values for transport mode Dual Iub:
"TOP"
"SG1" - Signalled traffic for pHB EF
"SG2" - Signalled traffic for pHB AF4
"SG3" - Signalled traffic for pHB AF3
"SG4" - Signalled traffic for pHB AF2
"SG5" - Signalled traffic for pHB AF1
"SG6" - Signalled traffic for pHB BE
"ICMP"
"BFD1" to "BFD16"
"OSPF" (on FIIB,FILB,FTIA,FTIB,FTJA,FTLB,FTFB, FIIF, FTIF units only)
404 DN70577885
Flexi Transport Module Parameters
Id:0900d80580975ffbConfidential
QOS Parameters
40.12 vlanPrio (Vlan priority flag)
Range 1...40
Units characters
Formula for getting internal value
internal_value = gui_value
Default value -
Default value notes -
Related functions -
Modification On-Line
Related parameters iHSPAmode of IPNO - Value "OSPF, CES and BFD" is not supported if iHSPA-mode is set to enabled.
Parameter relationships -
Related options • AND RAN2440 Fast IP Rerouting (optional) AND RAN1879 Dynamic routing by OSPF (optional) AND RAN2359 OSPF enhance-ments (optional) AND RAN74 Native Iub IP for Flexi WCDMA BTS (optional) AND RAN1253 Iub Transport QoS (optional)
Feature dependencies -
Interfaces • EM <-> FTM • RAC <-> FTM • RAC <-> RACApp
References -
Validation pattern -
Table 334 trafficType (Traffic type) (Cont.)
Parameter name Vlan priority flag
Abbreviated name vlanPrio
3GPP name -
Managed Object -
Multiplicity 1
Description This is the vlan priority to be used on all connec-tions for a given Per Hop Behaviour.
Range 0... 7
Units -
Table 335 vlanPrio (Vlan priority flag)
DN70577885 405
Flexi Transport Module Parameters QOS Parameters
Id:0900d80580975ffbConfidential
Formula for getting internal value
internal_value = gui_value
Default value 0
Default value notes -
Related functions -
Modification On-Line
Related parameters -
Parameter relationships -
Related options -
Feature dependencies -
Interfaces • EM <-> FTM • RAC <-> FTM • RAC <-> RACApp
References -
Validation pattern -
Table 335 vlanPrio (Vlan priority flag) (Cont.)
406 DN70577885
Flexi Transport Module Parameters
Id:0900d80580975ffbConfidential
SDHIF Parameters
41 SDHIF Parameters
41.1 administrativeState (Administrative State)
Parameter name Administrative State
Abbreviated name administrativeState
3GPP name -
Managed Object SDHIF
Multiplicity 1
Description Used to lock and unlock the interface.
Unlocking the interface triggers the creation of a TCTT (ATM interface).
Locking the interface deactivates it and all alarms and any ATM cell transfer is suppressed. Note that the associated TCTT (ATM interface) is not deleted.
Range locked (0), unlocked (1)
Units -
Formula for getting internal value
gui ==> internal
locked ==> 0
unlocked ==> 1
Default value locked (0)
Default value notes -
Related functions -
Modification On-Line
Related parameters -
Parameter relationships -
Related options -
Feature dependencies • Physical Interfaces STM1/OC3 & STM0/OC1
Interfaces • EM <-> FTM • RAC <-> FTM • RAC <-> RACApp
References -
Validation pattern -
Table 336 administrativeState (Administrative State)
DN70577885 407
Flexi Transport Module Parameters SDHIF Parameters
Id:0900d80580975ffbConfidential
41.2 interfaceNumber (Interface Number)
41.3 laserMode (Laser Mode)
Parameter name Interface Number
Abbreviated name interfaceNumber
3GPP name -
Managed Object SDHIF
Multiplicity 1
Description Defines the interface location on the unit.
Since the FTOA unit provides just one SDH inter-face, the number is fixed to 1.
Range 1... 1
Units -
Formula for getting internal value
internal_value = gui_value
Default value 1
Default value notes Fixed value 1.
Related functions -
Modification Not modifiable
Related parameters -
Parameter relationships -
Related options -
Feature dependencies • Physical Interfaces STM1/OC3 & STM0/OC1
Interfaces • FTM -> EM • FTM -> RAC
References -
Validation pattern -
Table 337 interfaceNumber (Interface Number)
Parameter name Laser Mode
Abbreviated name laserMode
3GPP name -
Managed Object SDHIF
Multiplicity 1
Table 338 laserMode (Laser Mode)
408 DN70577885
Flexi Transport Module Parameters
Id:0900d80580975ffbConfidential
SDHIF Parameters
41.4 rdiOnExcessiveBer (Remote Defect Indication On Exces-sive Bit Error Ratio)
Description Switches the laser on or off separately for each SDH interface. Automatic switching is not provided.
Range LASER_MODE_OFF (0), LASER_MODE_ON (1)
Units -
Formula for getting internal value
gui ==> internal
LASER_MODE_OFF ==> 0
LASER_MODE_ON ==> 1
Default value LASER_MODE_OFF (0)
Default value notes -
Related functions -
Modification On-Line
Related parameters -
Parameter relationships -
Related options -
Feature dependencies • Physical Interfaces STM1/OC3 & STM0/OC1
Interfaces • EM <-> FTM • RAC <-> FTM • RAC <-> RACApp
References -
Validation pattern -
Table 338 laserMode (Laser Mode) (Cont.)
Parameter name Remote Defect Indication On Excessive Bit Error Ratio
Abbreviated name rdiOnExcessiveBer
3GPP name -
Managed Object SDHIF
Multiplicity 1
Description Enables or disables RDI on EBER that is set in SDH/SONET frame if the Bit Error Ratio of the con-nection is exceeded.
Range false (0), true (1)
Units -
Table 339 rdiOnExcessiveBer (Remote Defect Indication On Excessive Bit Error Ratio)
DN70577885 409
Flexi Transport Module Parameters SDHIF Parameters
Id:0900d80580975ffbConfidential
41.5 sdhifId (SDH Interface Identifier)
Formula for getting internal value
• false => 0 • true => 1
Default value true (1)
Default value notes -
Related functions -
Modification On-Line
Related parameters -
Parameter relationships -
Related options -
Feature dependencies • Physical Interfaces STM1/OC3 & STM0/OC1
Interfaces • EM <-> FTM • RAC <-> FTM • RAC <-> RACApp
References -
Validation pattern -
Table 339 rdiOnExcessiveBer (Remote Defect Indication On Excessive Bit Error Ratio) (Cont.)
Parameter name SDH Interface Identifier
Abbreviated name sdhifId
3GPP name -
Managed Object SDHIF
Multiplicity 1
Description This MO class has only one instance in this release. The identifier is "1-1"
(unit#-if#)
Range 3
Units characters
Formula for getting internal value
internal_value = gui_value
Default value 1-1
Default value notes Value is always "1-1. In this release only one unit with at most one SDH interface is available.
Related functions -
Modification Not modifiable
Table 340 sdhifId (SDH Interface Identifier)
410 DN70577885
Flexi Transport Module Parameters
Id:0900d80580975ffbConfidential
SDHIF Parameters
41.6 unitNumber (Unit Number)
Related parameters -
Parameter relationships -
Related options -
Feature dependencies • Physical Interfaces STM1/OC3 & STM0/OC1
Interfaces • EM <-> FTM • RAC -> FTM • RAC <-> RACApp
References -
Validation pattern -
Table 340 sdhifId (SDH Interface Identifier) (Cont.)
Parameter name Unit Number
Abbreviated name unitNumber
3GPP name -
Managed Object SDHIF
Multiplicity 1
Description Specifies the location of the unit. In this release it is always 1.
Range 1... 1
Units -
Formula for getting internal value
internal_value = gui_value
Default value -
Default value notes -
Related functions -
Modification Not modifiable
Related parameters -
Parameter relationships -
Related options -
Feature dependencies • Physical Interfaces STM1/OC3 & STM0/OC1
Interfaces • EM <-> FTM • RAC <-> FTM • RAC <-> RACApp
References -
Table 341 unitNumber (Unit Number)
DN70577885 411
Flexi Transport Module Parameters SDHIF Parameters
Id:0900d80580975ffbConfidential
41.7 xmtTraceId_HP (Sent Trace Identifier (J1, HOP))
41.8 xmtTraceId_RS (Sent Trace Identifier (J0, RS))
Validation pattern -
Table 341 unitNumber (Unit Number) (Cont.)
Parameter name Sent Trace Identifier (J1, HOP)
Abbreviated name xmtTraceId_HP
3GPP name -
Managed Object SDHIF
Multiplicity 1
Description Specifies a signal label forwarded to the remote site on the High Order Path. The Trace Identifier is located in the J1 byte of the RSOH in the STM/SONET frame.
Range 0...15
Units characters
Formula for getting internal value
internal_value = gui_value
Default value -
Default value notes The empty string is default value and indicates that the feature is not used.
Related functions -
Modification On-Line
Related parameters -
Parameter relationships -
Related options -
Feature dependencies • Physical Interfaces STM1/OC3 & STM0/OC1
Interfaces • EM <-> FTM • RAC <-> FTM • RAC <-> RACApp
References -
Validation pattern -
Table 342 xmtTraceId_HP (Sent Trace Identifier (J1, HOP))
Parameter name Sent Trace Identifier (J0, RS)
Table 343 xmtTraceId_RS (Sent Trace Identifier (J0, RS))
412 DN70577885
Flexi Transport Module Parameters
Id:0900d80580975ffbConfidential
SDHIF Parameters
Abbreviated name xmtTraceId_RS
3GPP name -
Managed Object SDHIF
Multiplicity 1
Description Specifies a signal label forwarded to the remote site. The Trace Identifier is located in the J0 byte of the RSOH in the STM-1 frame. It is not supported on SONET interfaces.
As a default, no value is defined. In this case the Trace Identifier is not checked in the FTM.
Range 0...15
Units characters
Formula for getting internal value
internal_value = gui_value
Default value -
Default value notes The empty string is default value and indicates that the feature is not used.
Related functions -
Modification On-Line
Related parameters -
Parameter relationships -
Related options -
Feature dependencies • Physical Interfaces STM1/OC3 & STM0/OC1
Interfaces • EM <-> FTM • RAC <-> FTM • RAC <-> RACApp
References -
Validation pattern -
Table 343 xmtTraceId_RS (Sent Trace Identifier (J0, RS)) (Cont.)
DN70577885 413
Flexi Transport Module Parameters STPG Parameters
Id:0900d80580975ffbConfidential
42 STPG Parameters
42.1 ssmSelExt2M (SSM Selection with external 2.048 MHz)
Parameter name SSM Selection with external 2.048 MHz
Abbreviated name ssmSelExt2M
3GPP name -
Managed Object STPG
Multiplicity 1
Description This parameter is used for selection with external 2.048 MHz being sync reference.
Range PRC (0), SSU-A (1), SSU-B (2), EEC1 (3), PRS (4), Stratum2 (5), TraceabilityUnknown (6)
Units -
Formula for getting internal value
gui ==> internal
PRC ==> 0
SSU-A ==> 1
SSU-B ==> 2
EEC1 ==> 3
PRS ==> 4
Stratum2 ==> 5
TraceabilityUnknown ==> 6
Default value EEC1 (3)
Default value notes The default value in ITU is EEC1 and ANSI is "Traceability Unknown".
Related functions -
Modification On-Line
Related parameters -
Parameter relationships -
Related options -
Feature dependencies -
Interfaces • EM <-> FTM • FTM <-> RAC • RAC <-> RACApp
References NSN reference: CN4429 SyncE alignment to SSM acceptance level
Validation pattern -
Table 344 ssmSelExt2M (SSM Selection with external 2.048 MHz)
414 DN70577885
Flexi Transport Module Parameters
Id:0900d80580975ffbConfidential
STPG Parameters
42.2 ssmSelPDH (SSM Selection with TDM)
Parameter name SSM Selection with TDM
Abbreviated name ssmSelPDH
3GPP name -
Managed Object STPG
Multiplicity 1
Description This parameter is used for selection of SSM with TDM being sync reference.
Range PRC (0), SSU-A (1), SSU-B (2), EEC1 (3), PRS (4), Stratum2 (5), TraceabilityUnknown (6)
Units -
Formula for getting internal value
gui ==> internal
PRC ==> 0
SSU-A ==> 1
SSU-B ==> 2
EEC1 ==> 3
PRS ==> 4
Stratum2 ==> 5
TraceabilityUnknown ==> 6
Default value EEC1 (3)
Default value notes The default value in ITU is EEC1 and ANSI is "Traceability Unknown".
Related functions -
Modification On-Line
Related parameters -
Parameter relationships -
Related options -
Feature dependencies -
Interfaces • EM <-> FTM • FTM <-> RAC • RAC <-> RACApp
References NSN reference: CN4429 SyncE alignment to SSM acceptance level
Validation pattern -
Table 345 ssmSelPDH (SSM Selection with TDM)
DN70577885 415
Flexi Transport Module Parameters STPG Parameters
Id:0900d80580975ffbConfidential
42.3 ssmSelSyncE (SSM Selection with SyncE)
Parameter name SSM Selection with SyncE
Abbreviated name ssmSelSyncE
3GPP name -
Managed Object STPG
Multiplicity 1
Description This parameter is used for selection with SyncE being sync reference and SSM monitoring.
Range PRC (0), SSU-A (1), SSU-B (2), EEC1 (3), PRS (4), Stratum2 (5), TraceabilityUnknown (6)
Units -
Formula for getting internal value
gui ==> internal
PRC ==> 0
SSU-A ==> 1
SSU-B ==> 2
EEC1 ==> 3
PRS ==> 4
Stratum2 ==> 5
TraceabilityUnknown ==> 6
Default value EEC1 (3)
Default value notes The default value in ITU is EEC1 and ANSI is "Traceability Unknown".
Related functions -
Modification On-Line
Related parameters -
Parameter relationships -
Related options -
Feature dependencies -
Interfaces • EM <-> FTM • FTM <-> RAC • RAC <-> RACApp
References NSN reference: CN4429 SyncE alignment to SSM acceptance level
Validation pattern -
Table 346 ssmSelSyncE (SSM Selection with SyncE)
416 DN70577885
Flexi Transport Module Parameters
Id:0900d80580975ffbConfidential
STPG Parameters
42.4 ssmTxUntagged (Send SSM message frames untagged)
42.5 ssmType (SSM support network standard)
Parameter name Send SSM message frames untagged
Abbreviated name ssmTxUntagged
3GPP name -
Managed Object STPG
Multiplicity 1
Description If true, the frames of SSM messages transmitted for Synchronous Ethernet are mandatory untagged, even when sent on VLAN interfaces.
Range false (0), true (1)
Units -
Formula for getting internal value
• false => 0 • true => 1
Default value true (1)
Default value notes By default the frames are untagged.
Related functions -
Modification On-Line
Related parameters -
Parameter relationships -
Related options • RAN2071 Synchronous Ethernet Generation
Feature dependencies -
Interfaces • EM <-> FTM • RAC <-> FTM • RAC <-> RACApp
References -
Validation pattern -
Table 347 ssmTxUntagged (Send SSM message frames untagged)
Parameter name SSM support network standard
Abbreviated name ssmType
3GPP name -
Managed Object STPG
Multiplicity 1
Table 348 ssmType (SSM support network standard)
DN70577885 417
Flexi Transport Module Parameters STPG Parameters
Id:0900d80580975ffbConfidential
42.6 synchERegenOn (Activate the synchronous ethernet regenerator function)
Description This parameter specifies according to which network standard SSM messages shall be transmit-ted in synchronous Ethernet regeneration mode.
Range SSM_OFF (1), SSM_ITU (2), SSM_ANSI (3)
Units -
Formula for getting internal value
gui ==> internal
SSM_OFF ==> 1
SSM_ITU ==> 2
SSM_ANSI ==> 3
Default value SSM_ITU (2)
Default value notes Default is ITU / ETSI standard.
Related functions -
Modification On-Line
Related parameters -
Parameter relationships -
Related options • RAN2071 Synchronous Ethernet Generation
Feature dependencies -
Interfaces • EM <-> FTM • RAC <-> FTM • RAC <-> RACApp
References -
Validation pattern -
Table 348 ssmType (SSM support network standard) (Cont.)
Parameter name Activate the synchronous ethernet regenerator function
Abbreviated name synchERegenOn
3GPP name -
Managed Object STPG
Multiplicity 1
Table 349 synchERegenOn (Activate the synchronous ethernet regenerator function)
418 DN70577885
Flexi Transport Module Parameters
Id:0900d80580975ffbConfidential
STPG Parameters
42.7 synchroSourceList (The synchronization sources of the BTS)
Description This parameter switches the Synchronous Ethernet Regenerator function on.
NOTE: This parameter should not be allowed to be set to true in ATM Iub mode for FTFB,FTIF & FIIF.
Range false (0), true (1)
Units -
Formula for getting internal value
• false => 0 • true => 1
Default value false (0)
Default value notes By default the function is switched off.
Related functions -
Modification On-Line
Related parameters -
Parameter relationships -
Related options • RAN2071 Synchronous Ethernet Generation
Feature dependencies -
Interfaces • EM <-> FTM • RAC <-> FTM • RAC <-> RACApp
References -
Validation pattern -
Table 349 synchERegenOn (Activate the synchronous ethernet regenerator function) (Cont.)
Parameter name The synchronization sources of the BTS
Abbreviated name synchroSourceList
3GPP name -
Managed Object STPG
Multiplicity 2
Description This is the list of synchronization sources of the BTS. Up to 2 clock sources can be configured.
NOTE:Synchronous Ethernet synchronization source is not supported in the FTFB, FTIF, FIIF unit when it's in the ATM Iub transport mode.
Table 350 synchroSourceList (The synchronization sources of the BTS)
DN70577885 419
Flexi Transport Module Parameters STPG Parameters
Id:0900d80580975ffbConfidential
42.8 clockProtocol (Protocol of the clock source)
Formula for getting internal value
-
Default value -
Default value notes -
Related functions -
Child parameters • clockProtocol • interfaceNumber • priority • ssmAcceptanceLevel • ssmEnabled • ssmTimeout • unitNumber
Modification On-Line
Related parameters -
Parameter relationships -
Related options • RAN1254 Timing over Packet • RAN1708 Synchronuous Ethernet
Feature dependencies -
Interfaces • EM <-> FTM • RAC <-> FTM • RAC <-> RACApp
References -
Validation pattern -
Table 350 synchroSourceList (The synchronization sources of the BTS) (Cont.)
Parameter name Protocol of the clock source
Abbreviated name clockProtocol
3GPP name -
Managed Object -
Multiplicity 1
Description This parameter holds the protocol of this clock source: PDH, SDH, synchronuous Ethernet, Timing over Packet or the external 2 MHz clock.
Note: SyncE and TOP source does not support unit types FTFB, FTIF and FIIF when transport mode is Atm Iub
Table 351 clockProtocol (Protocol of the clock source)
420 DN70577885
Flexi Transport Module Parameters
Id:0900d80580975ffbConfidential
STPG Parameters
42.9 interfaceNumber (Interface number)
Range clkPDH (1), clkSDH (2), clkSyncE (3), clkToP (4)
Units -
Formula for getting internal value
gui ==> internal
clkPDH ==> 1
clkSDH ==> 2
clkSyncE ==> 3
clkToP ==> 4
Default value -
Default value notes -
Related functions -
Modification On-Line
Related parameters -
Parameter relationships -
Related options • RAN1254 Timing over Packet • RAN1708 Synchronuous Ethernet
Feature dependencies -
Interfaces • EM <-> FTM • RAC <-> FTM • RAC <-> RACApp
References -
Validation pattern -
Table 351 clockProtocol (Protocol of the clock source) (Cont.)
Parameter name Interface number
Abbreviated name interfaceNumber
3GPP name -
Managed Object -
Multiplicity 1
Table 352 interfaceNumber (Interface number)
DN70577885 421
Flexi Transport Module Parameters STPG Parameters
Id:0900d80580975ffbConfidential
Description This parameter specifies either
- the PDH interface on the unit for a PDH synchro-nization source, or
- the SDH interface on the unit for a SDH clock source, or
- the Ethernet interface on the unit for the synchro-nous Ethernet synchronization source.
In case of Timing over Packet the BTS automati-cally selects the Ethernet link. This parameter is ignored.
In case the external clock is selected as synchroni-zation source the parameter is ignored by the BTS. Recommended value is 0 in this case.
Examples:
interfaceNumber=1, unitNumber=1, clockProto-col=clkPDH: This means PDH interface number 1 on unit 1.
interfaceNumber=1, unitNumber=1, clockProto-col=clkSyncE: This means Ethernet interface number 1 on unit 1.
Range 0... 16
Units -
Formula for getting internal value
internal_value = gui_value
Default value -
Default value notes -
Related functions -
Modification On-Line
Related parameters -
Parameter relationships -
Related options • RAN1254 Timing over Packet • RAN1708 Synchronuous Ethernet
Feature dependencies -
Interfaces • EM <-> FTM • RAC <-> FTM • RAC <-> RACApp
References -
Validation pattern -
Table 352 interfaceNumber (Interface number) (Cont.)
422 DN70577885
Flexi Transport Module Parameters
Id:0900d80580975ffbConfidential
STPG Parameters
42.10 priority (Clock source priority)
42.11 ssmAcceptanceLevel (SSM defined value)
Parameter name Clock source priority
Abbreviated name priority
3GPP name -
Managed Object -
Multiplicity 1
Description This parameter holds the priority in which the clock sources of the BTS are to be taken into use. Value 1 ist highest priority: this clock source will be taken first.
Range 1... 2
Units -
Formula for getting internal value
internal_value = gui_value
Default value -
Default value notes -
Related functions -
Modification On-Line
Related parameters -
Parameter relationships -
Related options • RAN1254 Timing over Packet • RAN1708 Synchronuous Ethernet
Feature dependencies -
Interfaces • EM <-> FTM • RAC <-> FTM • RAC <-> RACApp
References -
Validation pattern -
Table 353 priority (Clock source priority)
Parameter name SSM defined value
Abbreviated name ssmAcceptanceLevel
3GPP name -
Managed Object -
Table 354 ssmAcceptanceLevel (SSM defined value)
DN70577885 423
Flexi Transport Module Parameters STPG Parameters
Id:0900d80580975ffbConfidential
42.12 ssmEnabled (SSM enabling flag)
Multiplicity 1
Description This is the defined SSM value (defined quality of the source clock). An alarm will be raised, If the quality falls below this value for ssmTimeout seconds.
Range ssmPRCorPRS (1), ssmSSU (2)
Units -
Formula for getting internal value
gui ==> internal
ssmPRCorPRS ==> 1
ssmSSU ==> 2
Default value 1
Default value notes -
Related functions -
Modification On-Line
Related parameters clockProtocol of STPG - This parameter is only relevant in case the value of parameter clockProtocol is equal to clkSyncE (Syn-chronuous Ethernet clock source).
ssmTimeout of STPG - An alarm is raised if the observed quality of clock source is below ssmAcceptanceLevel for a period of ssm-Timeout seconds.
Parameter relationships -
Related options • RAN1708 Synchronuous Ethernet
Feature dependencies -
Interfaces • EM <-> FTM • RAC <-> FTM • RAC <-> RACApp
References -
Validation pattern -
Table 354 ssmAcceptanceLevel (SSM defined value) (Cont.)
Parameter name SSM enabling flag
Abbreviated name ssmEnabled
3GPP name -
Managed Object -
Multiplicity 1
Table 355 ssmEnabled (SSM enabling flag)
424 DN70577885
Flexi Transport Module Parameters
Id:0900d80580975ffbConfidential
STPG Parameters
42.13 ssmTimeout (SSM message timeout)
Description This parameter enables Synchronization Status Message (SSM) support for Synchronuous Ether-net.
Range false (0), true (1)
Units -
Formula for getting internal value
• false => 0 • true => 1
Default value true (1)
Default value notes By default SSM support is enabled.
Related functions -
Modification On-Line
Related parameters clockProtocol of STPG - This parameter is only relevant in case the value of parameter clockProtocol is equal to clkSyncE (Syn-chronuous Ethernet clock source).
Parameter relationships -
Related options • RAN1708 Synchronuous Ethernet
Feature dependencies -
Interfaces • EM <-> FTM • RAC <-> FTM • RAC <-> RACApp
References -
Validation pattern -
Table 355 ssmEnabled (SSM enabling flag) (Cont.)
Parameter name SSM message timeout
Abbreviated name ssmTimeout
3GPP name -
Managed Object -
Multiplicity 1
Table 356 ssmTimeout (SSM message timeout)
DN70577885 425
Flexi Transport Module Parameters STPG Parameters
Id:0900d80580975ffbConfidential
42.14 unitNumber (Unit number)
Description This is the maximum duration in seconds for which the actual SSM value may be less than a required clock quality. If the duration is surpassed, an alarm will be raised.
If SSM support is according to network standard ITU / ETSI, an alarm will be raised if the observed SSM value falls below ssmPRC quality for ssmTim-eout seconds.
If SSM support is according to network standard ANSI / SONET, an alarm will be raised if the observed SSM value falls below ssmPRS quality for ssmTimeout seconds.
Range 2... 10
Units seconds
Formula for getting internal value
internal_value = gui_value
Default value 5
Default value notes -
Related functions -
Modification On-Line
Related parameters clockProtocol of STPG - This parameter is only relevant in case the value of parameter clockProtocol is equal to clkSyncE (Syn-chronuous Ethernet clock source).
Parameter relationships -
Related options • RAN1708 Synchronuous Ethernet
Feature dependencies -
Interfaces • EM <-> FTM • RAC <-> FTM • RAC <-> RACApp
References -
Validation pattern -
Table 356 ssmTimeout (SSM message timeout) (Cont.)
Parameter name Unit number
Abbreviated name unitNumber
3GPP name -
Table 357 unitNumber (Unit number)
426 DN70577885
Flexi Transport Module Parameters
Id:0900d80580975ffbConfidential
STPG Parameters
42.15 timingGenPgId (Synchronisation Protection Group Identi-fier)
Managed Object -
Multiplicity 1
Description This parameter specifies the location of the unit providing the synchronisation source interface. unitNumber shall be "0" for ToP sync source when unit is FSM/FSI/FTIF/FIIF.
Range 1... 1 for WN7.0 1.0
0... 1 for WN7.0 2.0
Units -
Formula for getting internal value
internal_value = gui_value
Default value -
Default value notes -
Related functions -
Modification On-Line
Related parameters -
Parameter relationships -
Related options • RAN1254 Timing over Packet • RAN1708 Synchronuous Ethernet
Feature dependencies -
Interfaces • EM <-> FTM • RAC <-> FTM • RAC <-> RACApp
References -
Validation pattern -
Table 357 unitNumber (Unit number) (Cont.)
Parameter name Synchronisation Protection Group Identifier
Abbreviated name timingGenPgId
3GPP name -
Managed Object STPG
Multiplicity 1
Table 358 timingGenPgId (Synchronisation Protection Group Identifier)
DN70577885 427
Flexi Transport Module Parameters STPG Parameters
Id:0900d80580975ffbConfidential
Description This parameter identifies the BTS transport syn-chronisation protection group. The value is always 1.
Range 1... 1
Units -
Formula for getting internal value
internal_value = gui_value
Default value -
Default value notes -
Related functions -
Modification Not modifiable
Related parameters -
Parameter relationships -
Related options -
Feature dependencies -
Interfaces • EM <-> FTM • RAC -> FTM • RAC <-> RACApp
References -
Validation pattern -
Table 358 timingGenPgId (Synchronisation Protection Group Identifier) (Cont.)
428 DN70577885
Flexi Transport Module Parameters
Id:0900d80580975ffbConfidential
SYNC Parameters
43 SYNC Parameters
43.1 syncId (Clock Synchronization Configuration Identifier)
Parameter name Clock Synchronization Configuration Identifier
Abbreviated name syncId
3GPP name -
Managed Object SYNC
Multiplicity 1
Description This parameter identifies the BTS transport clock synchronization configuration. The value is always 1.
Range 1... 1
Units -
Formula for getting internal value
internal_value = gui_value
Default value -
Default value notes -
Related functions -
Modification Not modifiable
Related parameters -
Parameter relationships -
Related options -
Feature dependencies -
Interfaces • EM <-> FTM • RAC -> FTM • RAC <-> RACApp
References -
Validation pattern -
Table 359 syncId (Clock Synchronization Configuration Identifier)
DN70577885 429
Flexi Transport Module Parameters TCTT Parameters
Id:0900d80580975ffbConfidential
44 TCTT Parameters
44.1 interfaceNumber (Interface number)
Parameter name Interface number
Abbreviated name interfaceNumber
3GPP name -
Managed Object TCTT
Multiplicity 1
Description Defines the location of the physical interface on the unit.
The value range depends on the unit type.
FTEB, FTPB, FTIF, FIIF: 1..8
FIIB, FILB, FTIA, FTIB, FTJA, FTLB: 1..4
FTFB, FTFA, FTHA: 1..16
In case of Inverse Multiplexing for ATM (IMA) the value range is: 33..75.
For ATM over Ethernet, the value is always: 76.
Range 1... 76
Units -
Formula for getting internal value
internal_value = gui_value
Default value -
Default value notes -
Related functions -
Modification Not modifiable
Related parameters imaGroupId of IMAG
Parameter relationships If the TC adapter is associated to an IMA group, the imaGroupId is used as interface number
Related options -
Feature dependencies -
Interfaces • FTM -> EM • FTM -> RAC
References -
Validation pattern -
Table 360 interfaceNumber (Interface number)
430 DN70577885
Flexi Transport Module Parameters
Id:0900d80580975ffbConfidential
TCTT Parameters
44.2 tcAdaptorTTPId (ATM Interface Identifier)
Parameter name ATM Interface Identifier
Abbreviated name tcAdaptorTTPId
3GPP name -
Managed Object TCTT
Multiplicity 1
Description Naming attribute
The object is identified by
- Interface Type (PPTT, IMAG, PWTIP, SVTT)
- UnitNumber (always "1")
- InterfaceNumber (if#, must be equal to the attri-bute interfaceNumber)
Format:
- PPTT-1-if#
- IMAG-1-if#
- PWTIP-1-76
- SVTT-1-1
Range 8...10
Units characters
Formula for getting internal value
internal_value = gui_value
Default value -
Default value notes -
Related functions -
Modification Not modifiable
Related parameters interfaceNumber of TCTT - The value of the attribute interfaceNumber is contained in the ATM interface identifier.
Parameter relationships -
Related options -
Feature dependencies -
Interfaces • EM <-> FTM • RAC -> FTM • RAC <-> RACApp
References -
Validation pattern -
Table 361 tcAdaptorTTPId (ATM Interface Identifier)
DN70577885 431
Flexi Transport Module Parameters TCTT Parameters
Id:0900d80580975ffbConfidential
44.3 unitNumber (Unit Number)
Parameter name Unit Number
Abbreviated name unitNumber
3GPP name -
Managed Object TCTT
Multiplicity 1
Description Specifies the location of the unit. In this release it is always 1.
Range 1... 1
Units -
Formula for getting internal value
internal_value = gui_value
Default value -
Default value notes -
Related functions -
Modification Not modifiable
Related parameters -
Parameter relationships -
Related options -
Feature dependencies -
Interfaces • FTM -> EM • FTM -> RAC
References -
Validation pattern -
Table 362 unitNumber (Unit Number)
432 DN70577885
Flexi Transport Module Parameters
Id:0900d80580975ffbConfidential
TMPAR Parameters
45 TMPAR Parameters
45.1 cacCommittedBitRate (CAC Committed Bit Rate)
Parameter name CAC Committed Bit Rate
Abbreviated name cacCommittedBitRate
3GPP name -
Managed Object TMPAR
Multiplicity 1
Table 363 cacCommittedBitRate (CAC Committed Bit Rate)
DN70577885 433
Flexi Transport Module Parameters TMPAR Parameters
Id:0900d80580975ffbConfidential
Description Connection Admission Control Committed Bit Rate
- Used in Dual Iub and Iub/IP transport modes
In case there is just one IP interface (IVIF, IEIF, P3xL) or when shaping is WFQ (IEIF/trafficPath-ShapingEnable) CAC committed bit rate is a total bit rate, which is available for guaranteed traffic at the Iub. In Iub/IP mode (not in dual Iub mode) sig-nalling bit rate and DCN bit rate are subtracted from the CAC committed bit rate and the rest is available for the user-plane data connections which are under transport connection admission control.
If there are several IP interfaces and shaping is PATH, Connection Admission Control is based on CIR parameter of the IP interface (IVIF, IEIF) that user plane uses.
The value range depends on the network interface type.
Fast Ethernet: 400 Kbps to 99900 Kbps with step of 100 Kbps
Gigabit Eth: 400 Kbps to 999900 Kbps with step of 100 Kbps
Multi Link PPP (P3ML): Connection Admission Control is based on the summed capacity of the PPP links included. CAC Committed bit rate param-eter value is omitted in this case. Signalling bit rate and DCN bit rate are subtracted from the PPP link capacity and the rest is available for the user-plane data connections which are under transport con-nection admission control.
Single Link PPP (P3SL): Connection Admission Control is based on the capacity of the PPP link included. CAC Committed bit rate parameter value is omitted in this case. Signalling bit rate and DCN bit rate are subtracted from the PPP link capacity and the rest is available for the user-plane data con-nections which are under transport connection admission control.
Range 400... 999900
Units kbps
Formula for getting internal value
internal_value = gui_value
Default value -
Default value notes -
Related functions -
Table 363 cacCommittedBitRate (CAC Committed Bit Rate) (Cont.)
434 DN70577885
Flexi Transport Module Parameters
Id:0900d80580975ffbConfidential
TMPAR Parameters
45.2 dcnCommittedBitRate (DCN Committed Bit Rate)
Modification On-Line
Related parameters transportMode of IPNO
Parameter relationships cacCommittedBitRate is relevant only for transport modes Dual Iub and Iub/IP.
Related options • RAN1449 Dual Iub for Flexi WCDMA • RAN74 Native Iub IP for Flexi WCDMA BTS
Feature dependencies -
Interfaces • EM <-> FTM • RAC <-> FTM • RAC <-> RACApp
References -
Validation pattern -
Table 363 cacCommittedBitRate (CAC Committed Bit Rate) (Cont.)
Parameter name DCN Committed Bit Rate
Abbreviated name dcnCommittedBitRate
3GPP name -
Managed Object TMPAR
Multiplicity 1
Description DCN Committed Bit Rate. Used in transport mode Iub/IP.
Range 50... 1000
Units kbps
Formula for getting internal value
internal_value = gui_value
Default value -
Default value notes -
Related functions -
Modification On-Line
Related parameters transportMode of IPNO
Parameter relationships dcnCommitttedBitRate is only relevant for transport mode Iub/IP.
Related options • RAN74 Native Iub IP for Flexi WCDMA BTS
Feature dependencies -
Table 364 dcnCommittedBitRate (DCN Committed Bit Rate)
DN70577885 435
Flexi Transport Module Parameters TMPAR Parameters
Id:0900d80580975ffbConfidential
45.3 externalNATIpAddress (External NAT IP Address)
Interfaces • EM <-> FTM • RAC <-> FTM • RAC <-> RACApp
References -
Validation pattern -
Table 364 dcnCommittedBitRate (DCN Committed Bit Rate) (Cont.)
Parameter name External NAT IP Address
Abbreviated name externalNATIpAddress
3GPP name -
Managed Object TMPAR
Multiplicity 1
Description This is the IP address to be used in addressing the external NAT device.
Range 7...15
Units characters
Formula for getting internal value
internal_value = gui_value
Default value -
Default value notes -
Related functions -
Modification On-Line
Related parameters -
Parameter relationships -
Related options • RAN1449 Dual Iub for Flexi WCDMA
Feature dependencies -
Interfaces • EM <-> FTM • RAC <-> FTM • RAC <-> RACApp
References -
Validation pattern -
Table 365 externalNATIpAddress (External NAT IP Address)
436 DN70577885
Flexi Transport Module Parameters
Id:0900d80580975ffbConfidential
TMPAR Parameters
45.4 farEndSctpSubnetIpAddress (Far End SCTP Subnet IP Address )
Parameter name Far End SCTP Subnet IP Address
Abbreviated name farEndSctpSubnetIpAddress
3GPP name -
Managed Object TMPAR
Multiplicity 1
Description This is the IP address to be used in the transport network at the far end of the SCTP tunnel. The address is the SCTP tunnel subnet address, i.e all its host bits must be set to 0´s. It must be entered in dotted decimal format.
The parameter is used in Iub/IP transport mode.
The associated subnet mask is defined in parame-ter farEndSctpSubnetMask.
Range 7...15
Units characters
Formula for getting internal value
internal_value = gui_value
Default value -
Default value notes -
Related functions -
Modification On-Line
Related parameters transportMode of IPNO
Parameter relationships farEndSctpSubnetIpAddress is only relevant in transportMode Iub/IP.
Related options • RAN74 Native Iub IP for Flexi WCDMA BTS
Feature dependencies -
Interfaces • EM <-> FTM • RAC <-> FTM • RAC <-> RACApp
References -
Validation pattern -
Table 366 farEndSctpSubnetIpAddress (Far End SCTP Subnet IP Address )
DN70577885 437
Flexi Transport Module Parameters TMPAR Parameters
Id:0900d80580975ffbConfidential
45.5 farEndSctpSubnetMask (Far End SCTP Subnet Mask)
45.6 minSCTPPort (Minimum SCTP port number)
Parameter name Far End SCTP Subnet Mask
Abbreviated name farEndSctpSubnetMask
3GPP name -
Managed Object TMPAR
Multiplicity 1
Description This is the subnet mask for the far end SCTP tunnel subnet IP address (parameter farEndSctpSubnetI-pAddress). To be entered in dotted decimal format.
Range 7...15
Units characters
Formula for getting internal value
internal_value = gui_value
Default value -
Default value notes -
Related functions -
Modification On-Line
Related parameters transportMode of IPNO
Parameter relationships The farEndSctpSubnetMask is only relevant in transport mode Iub/IP.
Related options • RAN74 Native Iub IP for Flexi WCDMA BTS
Feature dependencies -
Interfaces • EM <-> FTM • RAC <-> FTM • RAC <-> RACApp
References -
Validation pattern -
Table 367 farEndSctpSubnetMask (Far End SCTP Subnet Mask)
Parameter name Minimum SCTP port number
Abbreviated name minSCTPPort
3GPP name -
Managed Object TMPAR
Multiplicity 1
Table 368 minSCTPPort (Minimum SCTP port number)
438 DN70577885
Flexi Transport Module Parameters
Id:0900d80580975ffbConfidential
TMPAR Parameters
45.7 minUDPPort (Minimum UDP port number)
Description This is is the minimum value of the port number to be used for SCTP. Used in transport mode Iub/IP.
Range 49152... 65534
Units -
Formula for getting internal value
internal_value = gui_value
Default value 49152
Default value notes -
Related functions -
Modification On-Line
Related parameters transportMode of IPNO
Parameter relationships minSCTPPort is only relevant in transport mode Iub/IP.
Related options • RAN74 Native Iub IP for Flexi WCDMA BTS
Feature dependencies -
Interfaces • EM <-> FTM • RAC <-> FTM • RAC <-> RACApp
References -
Validation pattern -
Table 368 minSCTPPort (Minimum SCTP port number) (Cont.)
Parameter name Minimum UDP port number
Abbreviated name minUDPPort
3GPP name -
Managed Object TMPAR
Multiplicity 1
Description This is is the minimum value of the port number to be used for UDP connections.
The maximum value of this parameter = 63047, since 2488 calls are supported in transport modes Dual Iub an IubIP (65535 - 2488 = 63047).
Range 49152... 63047
Units -
Table 369 minUDPPort (Minimum UDP port number)
DN70577885 439
Flexi Transport Module Parameters TMPAR Parameters
Id:0900d80580975ffbConfidential
45.8 signallingCommittedBitRate (Signalling Committed Bit Rate)
Formula for getting internal value
internal_value = gui_value
Default value 49152
Default value notes -
Related functions -
Modification On-Line
Related parameters -
Parameter relationships -
Related options • RAN74 Native Iub IP for Flexi WCDMA BTS • RAN1449 Dual Iub for Flexi WCDMA
Feature dependencies -
Interfaces • EM <-> FTM • RAC <-> FTM • RAC <-> RACApp
References -
Validation pattern -
Table 369 minUDPPort (Minimum UDP port number) (Cont.)
Parameter name Signalling Committed Bit Rate
Abbreviated name signallingCommittedBitRate
3GPP name -
Managed Object TMPAR
Multiplicity 1
Description Signalling Committed Bit Rate. Used in transport mode Iub/IP.
Range 50... 1000
Units kbps
Formula for getting internal value
internal_value = gui_value
Default value -
Default value notes -
Related functions -
Modification On-Line
Table 370 signallingCommittedBitRate (Signalling Committed Bit Rate)
440 DN70577885
Flexi Transport Module Parameters
Id:0900d80580975ffbConfidential
TMPAR Parameters
45.9 tmparId (TMPAR Object Instance Identifier)
Related parameters transportMode of IPNO
Parameter relationships signallingCommittedBitRate is only relevant for transport mode Iub/IP.
Related options • RAN74 Native Iub IP for Flexi WCDMA BTS • RAN1449 Dual Iub for Flexi WCDMA
Feature dependencies -
Interfaces • EM <-> FTM • RAC <-> FTM • RAC <-> RACApp
References -
Validation pattern -
Table 370 signallingCommittedBitRate (Signalling Committed Bit Rate) (Cont.)
Parameter name TMPAR Object Instance Identifier
Abbreviated name tmparId
3GPP name -
Managed Object TMPAR
Multiplicity 1
Description This parameter identifies the unique object instance of the TMPAR clas. Value is always 1.
Range 1... 1
Units -
Formula for getting internal value
internal_value = gui_value
Default value -
Default value notes -
Related functions -
Modification Not modifiable
Related parameters -
Parameter relationships -
Related options -
Feature dependencies -
Interfaces • EM <-> FTM • RAC -> FTM • RAC <-> RACApp
Table 371 tmparId (TMPAR Object Instance Identifier)
DN70577885 441
Flexi Transport Module Parameters TMPAR Parameters
Id:0900d80580975ffbConfidential
References -
Validation pattern -
Table 371 tmparId (TMPAR Object Instance Identifier) (Cont.)
442 DN70577885
Flexi Transport Module Parameters
Id:0900d80580975ffbConfidential
TOPIK Parameters
46 TOPIK Parameters
46.1 administrativeState (Administrative State)
46.2 logMeanSyncValue (Log mean synchronization value)
Parameter name Administrative State
Abbreviated name administrativeState
3GPP name -
Managed Object TOPIK
Multiplicity 1
Description Used to lock and unlock the TOP object instance.
Locking the object deactivates it and supresses all its alarms.
Range locked (0), unlocked (1)
Units -
Formula for getting internal value
gui ==> internal
locked ==> 0
unlocked ==> 1
Default value locked (0)
Default value notes -
Related functions -
Modification On-Line
Related parameters -
Parameter relationships -
Related options • RAN1254 Timing over Packet
Feature dependencies -
Interfaces • EM <-> FTM • RAC <-> FTM • RAC <-> RACApp
References -
Validation pattern -
Table 372 administrativeState (Administrative State)
Parameter name Log mean synchronization value
Abbreviated name logMeanSyncValue
Table 373 logMeanSyncValue (Log mean synchronization value)
DN70577885 443
Flexi Transport Module Parameters TOPIK Parameters
Id:0900d80580975ffbConfidential
46.3 masterIpAddr (IP Address of the ToP master)
3GPP name -
Managed Object TOPIK
Multiplicity 1
Description This indicates how often a ToP sync message shall be send by the ToP master within the transmission duration request period. (The transmission duration request period is currently fixed to 300 seconds.)
The following values are defined:
-3: 8 per second
-4: 16 per second
-5: 32 per second
Range -5... -3
Units -
Formula for getting internal value
internal_value = gui_value
Default value -4
Default value notes This means 16 per second.
Related functions -
Modification On-Line
Related parameters -
Parameter relationships -
Related options • RAN1254 Timing over Packet
Feature dependencies -
Interfaces • EM <-> FTM • RAC <-> FTM • RAC <-> RACApp
References -
Validation pattern -
Table 373 logMeanSyncValue (Log mean synchronization value) (Cont.)
Parameter name IP Address of the ToP master
Abbreviated name masterIpAddr
3GPP name -
Managed Object TOPIK
Multiplicity 1
Table 374 masterIpAddr (IP Address of the ToP master)
444 DN70577885
Flexi Transport Module Parameters
Id:0900d80580975ffbConfidential
TOPIK Parameters
46.4 topId (Timing Over Packet Configuration Identifier)
Description IP address of the ToP master. To be entered in dotted format.
Range 7...15
Units characters
Formula for getting internal value
internal_value = gui_value
Default value -
Default value notes -
Related functions -
Modification On-Line
Related parameters administrativeState of TOPIK
Parameter relationships The parameter masterIpAddr shall have a regular value (not NULL, not 0.0.0.0, etc). whenever parameter administrativeState is set to unlocked.
Related options • RAN1254 Timing over Packet
Feature dependencies -
Interfaces • EM <-> FTM • RAC <-> FTM • RAC <-> RACApp
References -
Validation pattern -
Table 374 masterIpAddr (IP Address of the ToP master) (Cont.)
Parameter name Timing Over Packet Configuration Identifier
Abbreviated name topId
3GPP name -
Managed Object TOPIK
Multiplicity 1
Description This parameter identifies the BTS Timing over Packet (TOP) configuration. The value is always 1.
Range 1... 1
Units -
Formula for getting internal value
internal_value = gui_value
Default value -
Table 375 topId (Timing Over Packet Configuration Identifier)
DN70577885 445
Flexi Transport Module Parameters TOPIK Parameters
Id:0900d80580975ffbConfidential
Default value notes -
Related functions -
Modification Not modifiable
Related parameters -
Parameter relationships -
Related options • RAN1254 Timing over Packet
Feature dependencies -
Interfaces • EM <-> FTM • RAC -> FTM • RAC <-> RACApp
References -
Validation pattern -
Table 375 topId (Timing Over Packet Configuration Identifier) (Cont.)
446 DN70577885
Flexi Transport Module Parameters
Id:0900d80580975ffbConfidential
TRDE Parameters
47 TRDE Parameters
47.1 atmTrafficDescriptorId (Traffic Descriptor Identifier)
47.2 conformanceDefinition (Conformance Definition)
Parameter name Traffic Descriptor Identifier
Abbreviated name atmTrafficDescriptorId
3GPP name -
Managed Object TRDE
Multiplicity 1
Description This parameter identifies the traffic descriptor.
The value of the parameter shall represent a number starting with 100. Note that at most 32 traffic descriptors can exist in the AXC.
Range 3...10
Units characters
Formula for getting internal value
internal_value = gui_value
Default value -
Default value notes -
Related functions -
Modification Not modifiable
Related parameters -
Parameter relationships -
Related options -
Feature dependencies • ATM Traffic Management: UBR (Unspecified Bit Rate), CBR (Constant Bit Rate), Shaping
Interfaces • EM <-> FTM • RAC -> FTM • RAC <-> RACApp
References -
Validation pattern -
Table 376 atmTrafficDescriptorId (Traffic Descriptor Identifier)
Parameter name Conformance Definition
Abbreviated name conformanceDefinition
Table 377 conformanceDefinition (Conformance Definition)
DN70577885 447
Flexi Transport Module Parameters TRDE Parameters
Id:0900d80580975ffbConfidential
47.3 minDesiredCellRate (Minimum Desired Cell Rate)
3GPP name -
Managed Object TRDE
Multiplicity 1
Description Specifies the type of conformance test performed on the traffic stream by Usage Parameter Control (UPC).
The FTM enforces the correspondence between conformance definition and service category. For CBR the conformance definition is CBR.1 and for UBR UBR.1.
Range CBR1 (0), UBR1 (1)
Units -
Formula for getting internal value
gui ==> internal
CBR1 ==> 0
UBR1 ==> 1
Default value -
Default value notes Default values for service categories:CBR: CBR.1UBR: UBR.1
Related functions -
Modification On-Line
Related parameters -
Parameter relationships -
Related options -
Feature dependencies • ATM Traffic Management: UBR (Unspecified Bit Rate), CBR (Constant Bit Rate), Shaping
Interfaces • EM <-> FTM • RAC <-> FTM • RAC <-> RACApp
References -
Validation pattern -
Table 377 conformanceDefinition (Conformance Definition) (Cont.)
Parameter name Minimum Desired Cell Rate
Abbreviated name minDesiredCellRate
3GPP name -
Table 378 minDesiredCellRate (Minimum Desired Cell Rate)
448 DN70577885
Flexi Transport Module Parameters
Id:0900d80580975ffbConfidential
TRDE Parameters
47.4 peakCellRate (Peak Cell Rate)
Managed Object TRDE
Multiplicity 1
Description Minimum Desired Cell Rate (MDCR). Is the targeted minimum throughput of a UBR connection in cells per second. The parameter can be set optionally for UBR connections. The same value applies both for ingress and egress traffic.
Note: The value of the MDCR cannot exceed the PCR.
Range 0... 144896
Units cells/s
Formula for getting internal value
internal_value = gui_value
Default value 0
Default value notes -
Related functions -
Modification On-Line
Related parameters peakCellRate of TRDE
Parameter relationships The value of the MDCR cannot exceed the PCR.
Related options -
Feature dependencies • ATM Traffic Management: UBR (Unspecified Bit Rate), CBR (Constant Bit Rate), Shaping
Interfaces • EM <-> FTM • RAC <-> FTM • RAC <-> RACApp
References -
Validation pattern -
Table 378 minDesiredCellRate (Minimum Desired Cell Rate) (Cont.)
Parameter name Peak Cell Rate
Abbreviated name peakCellRate
3GPP name -
Managed Object TRDE
Multiplicity 1
Table 379 peakCellRate (Peak Cell Rate)
DN70577885 449
Flexi Transport Module Parameters TRDE Parameters
Id:0900d80580975ffbConfidential
47.5 ubrShare (UBR Share)
Description Specifies the peak cell rate (PCR) assigned or reserved in both egress and ingress directions of transmission across the VP or VC link that is termi-nated.
The rate is given in cells per seconds. It cannot be greater than the line rate of the source.
The exact allowed value range depends on the type of interface (E1, T1, SDH, IMA, ATMOverEthernet)
Range 36... 144896
Units cells/s
Formula for getting internal value
internal_value = gui_value
Default value -
Default value notes -
Related functions -
Modification On-Line
Related parameters -
Parameter relationships -
Related options -
Feature dependencies • ATM Traffic Management: UBR (Unspecified Bit Rate), CBR (Constant Bit Rate), Shaping
Interfaces • EM <-> FTM • RAC <-> FTM • RAC <-> RACApp
References -
Validation pattern -
Table 379 peakCellRate (Peak Cell Rate) (Cont.)
Parameter name UBR Share
Abbreviated name ubrShare
3GPP name -
Managed Object TRDE
Multiplicity 1
Table 380 ubrShare (UBR Share)
450 DN70577885
Flexi Transport Module Parameters
Id:0900d80580975ffbConfidential
TRDE Parameters
47.6 userLabel (User Label)
Description UBRshare allows to weight the traffic exceeding the Minim Desired Cell Rate among UBR connections that share the same ATM interface. An individual UBR connection may get at least the ingress MDCR and up to ingress MDCR + ingressUBRshare_i / Sum(ingress UBRshare_i) * ingress EBW. Where ingres EBW is the currently available ingress band-width for the traffic of all the UBR connections sharing the same ATM interface.
The value of UBR Share applies to both ingress and egress traffic.
Range 1... 1000
Units none
Formula for getting internal value
internal_value = gui_value
Default value 1
Default value notes -
Related functions -
Modification On-Line
Related parameters -
Parameter relationships -
Related options -
Feature dependencies • ATM Traffic Management: UBR (Unspecified Bit Rate), CBR (Constant Bit Rate), Shaping
Interfaces • EM <-> FTM • RAC <-> FTM • RAC <-> RACApp
References -
Validation pattern -
Table 380 ubrShare (UBR Share) (Cont.)
Parameter name User Label
Abbreviated name userLabel
3GPP name -
Managed Object TRDE
Multiplicity 1
Table 381 userLabel (User Label)
DN70577885 451
Flexi Transport Module Parameters TRDE Parameters
Id:0900d80580975ffbConfidential
Description A string used as label to describe the ATM traffic descriptor.
Range 1...20
Units characters
Formula for getting internal value
internal_value = gui_value
Default value -
Default value notes -
Related functions -
Modification On-Line
Related parameters -
Parameter relationships -
Related options -
Feature dependencies • ATM Traffic Management: UBR (Unspecified Bit Rate), CBR (Constant Bit Rate), Shaping
Interfaces • EM <-> FTM • RAC <-> FTM • RAC <-> RACApp
References -
Validation pattern -
Table 381 userLabel (User Label) (Cont.)
452 DN70577885
Flexi Transport Module Parameters
Id:0900d80580975ffbConfidential
TWAMP Parameters
48 TWAMP Parameters
48.1 administrativeState (Lock or unlock a TWAMP session)
Parameter name Lock or unlock a TWAMP session
Abbreviated name administrativeState
3GPP name -
Managed Object TWAMP
Multiplicity 1
Description This parameter locks or unlocks the TWAMP session. Locking a session stops it. Unlocking a session starts or re-starts it.
Starting or re-starting a session clears all statistics and alarms for the session. Stopping a session clears TWAMP alarms but not TWAMP statistics.
Range locked (0), unlocked (1)
Units -
Formula for getting internal value
gui ==> internal
locked ==> 0
unlocked ==> 1
Default value locked (0)
Default value notes By default the TWAMP session is locked.
Related functions -
Modification On-Line
Related parameters -
Parameter relationships -
Related options • RAN1900 IP Transport Network Measurement
Feature dependencies -
Interfaces • EM <-> FTM • RAC <-> FTM • RAC <-> RACApp
References -
Validation pattern -
Table 382 administrativeState (Lock or unlock a TWAMP session)
DN70577885 453
Flexi Transport Module Parameters TWAMP Parameters
Id:0900d80580975ffbConfidential
48.2 destIpAddress (TWAMP session destination IP address)
48.3 destPort (TWAMP session destination port)
Parameter name TWAMP session destination IP address
Abbreviated name destIpAddress
3GPP name -
Managed Object TWAMP
Multiplicity 1
Description This parameter specifies the destination IP address of the TWAMP session. The TWAMP session must be locked, before its destination IP address can be changed.
Range 7...15
Units characters
Formula for getting internal value
internal_value = gui_value
Default value -
Default value notes -
Related functions -
Modification Requires object locking
Related parameters administrativeState of TWAMP - The TWAMP session must be locked, before its destination IP address can be changed (set admin-istrativeState to "locked").
Parameter relationships -
Related options • RAN1900 IP Transport Network Measurement
Feature dependencies -
Interfaces • EM <-> FTM • RAC <-> FTM • RAC <-> RACApp
References -
Validation pattern -
Table 383 destIpAddress (TWAMP session destination IP address)
Parameter name TWAMP session destination port
Abbreviated name destPort
3GPP name -
Table 384 destPort (TWAMP session destination port)
454 DN70577885
Flexi Transport Module Parameters
Id:0900d80580975ffbConfidential
TWAMP Parameters
48.4 dscp (DSCP value for TWAMP message transmission)
Managed Object TWAMP
Multiplicity 1
Description This parameter specifies the destination port for TWAMP initiator messages. Changeing the desti-nation port of the TWAMP session requires locking the session.
Range 1... 65535
Units -
Formula for getting internal value
internal_value = gui_value
Default value 5000
Default value notes -
Related functions -
Modification Requires object locking
Related parameters administrativeState of TWAMP - Changeing the destination port of the session requires locking it.
Parameter relationships -
Related options • RAN1900 IP Transport Network Measurement
Feature dependencies -
Interfaces • EM <-> FTM • RAC <-> FTM • RAC <-> RACApp
References -
Validation pattern -
Table 384 destPort (TWAMP session destination port) (Cont.)
Parameter name DSCP value for TWAMP message transmission
Abbreviated name dscp
3GPP name -
Managed Object TWAMP
Multiplicity 1
Table 385 dscp (DSCP value for TWAMP message transmission)
DN70577885 455
Flexi Transport Module Parameters TWAMP Parameters
Id:0900d80580975ffbConfidential
48.5 messageSize (TWAMP initiator message size)
Description This parameter specifies the DSCP value to be used for transmission of TWAMP messages over the session. The corresponding mapping to a Per Hop Behaviour priority queue is contained in table trafficTypesMap of the QOS managed object class.
Range 0... 63
Units -
Formula for getting internal value
internal_value = gui_value
Default value 34
Default value notes The default DSCP value maps to Per Hop Behav-iour Assured Forwarding Class 4 (AF4).
Related functions -
Modification On-Line
Related parameters -
Parameter relationships -
Related options • RAN1900 IP Transport Network Measurement
Feature dependencies -
Interfaces • EM <-> FTM • RAC <-> FTM • RAC <-> RACApp
References -
Validation pattern -
Table 385 dscp (DSCP value for TWAMP message transmission) (Cont.)
Parameter name TWAMP initiator message size
Abbreviated name messageSize
3GPP name -
Managed Object TWAMP
Multiplicity 1
Description This parameter specifies the size of the TWAMP messages sent by the TWAMP initiator on this session. The value of the parameter shall not exceed the Maximum Transfer Unit value of the FTM.
Range 69... 1500
Table 386 messageSize (TWAMP initiator message size)
456 DN70577885
Flexi Transport Module Parameters
Id:0900d80580975ffbConfidential
TWAMP Parameters
48.6 plrAlarmThreshold (Packet loss ratio alarm threshold)
Units -
Formula for getting internal value
internal_value = gui_value
Default value 100
Default value notes Default value is 100 octets.
Related functions -
Modification On-Line
Related parameters mtu of IPNO - The value of the parameter messageSize shall not exceed the Maximum Transfer Unit value of the FTM.
Parameter relationships -
Related options • RAN1900 IP Transport Network Measurement
Feature dependencies -
Interfaces • EM <-> FTM • RAC <-> FTM • RAC <-> RACApp
References -
Validation pattern -
Table 386 messageSize (TWAMP initiator message size) (Cont.)
Parameter name Packet loss ratio alarm threshold
Abbreviated name plrAlarmThreshold
3GPP name -
Managed Object TWAMP
Multiplicity 1
Description This parameter specifies the threshold for raising the TWAMP session alarm for reasons of excessive packet loss ratio (PRL).
The alarm is raised, if the packet loss ratio observed over a 15 minute evalutation period exceeds the threshold value. The alarm will be cleared if the packet loss ratio drops below the threshold value for 2 consecutive 15-minute obser-vation periods.
Range 0... 10000
Units 0.01%
Table 387 plrAlarmThreshold (Packet loss ratio alarm threshold)
DN70577885 457
Flexi Transport Module Parameters TWAMP Parameters
Id:0900d80580975ffbConfidential
48.7 rttAlarmThreshold (Round-trip-time alarm threshold)
Formula for getting internal value
internal_value = gui_value
Default value 10000
Default value notes Default value is 100 percent. This means the alarm is only raised if packet loss = 100%.
Related functions -
Modification On-Line
Related parameters -
Parameter relationships -
Related options • RAN1900 IP Transport Network Measurement
Feature dependencies -
Interfaces • EM <-> FTM • RAC <-> FTM • RAC <-> RACApp
References -
Validation pattern -
Table 387 plrAlarmThreshold (Packet loss ratio alarm threshold) (Cont.)
Parameter name Round-trip-time alarm threshold
Abbreviated name rttAlarmThreshold
3GPP name -
Managed Object TWAMP
Multiplicity 1
Description This parameter specifies the threshold for raising the TWAMP session alarm for reasons of excessive round-trip-time (RTT).
The alarm is raised if the average round-trip-time of the TWAMP messages, calculated during a 1-minute evaluation period, exceeds the configured threshold. The alarm will be cleared, if during 5 con-secutive 1-minute periods the average value of the RTT remains below the threshold.
Range 0... 1000000
Units microseconds
Formula for getting internal value
internal_value = gui_value
Table 388 rttAlarmThreshold (Round-trip-time alarm threshold)
458 DN70577885
Flexi Transport Module Parameters
Id:0900d80580975ffbConfidential
TWAMP Parameters
48.8 sourceIpAddress (TWAMP initiator messages source IP address)
Default value 1000000
Default value notes Default value is 1 second.
Related functions -
Modification On-Line
Related parameters -
Parameter relationships -
Related options • RAN1900 IP Transport Network Measurement
Feature dependencies -
Interfaces • EM <-> FTM • RAC <-> FTM • RAC <-> RACApp
References -
Validation pattern -
Table 388 rttAlarmThreshold (Round-trip-time alarm threshold) (Cont.)
Parameter name TWAMP initiator messages source IP address
Abbreviated name sourceIpAddress
3GPP name -
Managed Object TWAMP
Multiplicity 1
Description This parameter specifies the source IP address of TWAMP initiator messages. The TWAMP session must be locked, before its source IP address can be changed.
Range 7...15
Units characters
Formula for getting internal value
internal_value = gui_value
Default value -
Default value notes -
Related functions -
Modification On-Line
Table 389 sourceIpAddress (TWAMP initiator messages source IP address)
DN70577885 459
Flexi Transport Module Parameters TWAMP Parameters
Id:0900d80580975ffbConfidential
48.9 twampId (TWAMP session identifier)
Related parameters administrativeState of TWAMP - The TWAMP session must be locked, before its source IP address can be changed (set administra-tiveState to "locked").
Parameter relationships -
Related options • RAN1900 IP Transport Network Measurement
Feature dependencies -
Interfaces • EM <-> FTM • RAC <-> FTM • RAC <-> RACApp
References -
Validation pattern -
Table 389 sourceIpAddress (TWAMP initiator messages source IP address) (Cont.)
Parameter name TWAMP session identifier
Abbreviated name twampId
3GPP name -
Managed Object TWAMP
Multiplicity 1
Description This parameter identifies a TWAMP session.
Range 1... 10
Units -
Formula for getting internal value
internal_value = gui_value
Default value -
Default value notes -
Related functions -
Modification Not modifiable
Related parameters -
Parameter relationships -
Related options • RAN1900 IP Transport Network Measurement
Feature dependencies -
Interfaces • EM <-> FTM • RAC -> FTM • RAC <-> RACApp
Table 390 twampId (TWAMP session identifier)
460 DN70577885
Flexi Transport Module Parameters
Id:0900d80580975ffbConfidential
TWAMP Parameters
References -
Validation pattern -
Table 390 twampId (TWAMP session identifier) (Cont.)
DN70577885 461
Flexi Transport Module Parameters UNIT Parameters
Id:0900d80580975ffbConfidential
49 UNIT Parameters
49.1 enableRP301Interface (Enable RP3-01 interface)
49.2 unitId (Unit Identifier)
Parameter name Enable RP3-01 interface
Abbreviated name enableRP301Interface
3GPP name -
Managed Object UNIT
Multiplicity 1
Description Configure and designate EIF2(Out-door)/EIF5(Indoor) on the Flexi System Module (FCT) as RP3-01 interface
Range false (0), true (1)
Units -
Formula for getting internal value
• false => 0 • true => 1
Default value false (0)
Default value notes -
Related functions -
Modification BTS restart needed
Related parameters unitTypeExpected of UNIT - This parameter is applicable only when unitTypeEx-pected is one of FTIF, FIIF, FSM, or FSI.
Parameter relationships -
Related options -
Feature dependencies -
Interfaces • EM <-> FTM • RAC <-> FTM • RAC <-> RACApp
References -
Validation pattern -
Table 391 enableRP301Interface (Enable RP3-01 interface)
Parameter name Unit Identifier
Abbreviated name unitId
Table 392 unitId (Unit Identifier)
462 DN70577885
Flexi Transport Module Parameters
Id:0900d80580975ffbConfidential
UNIT Parameters
49.3 unitTypeActual (Installed hardware unit type)
3GPP name -
Managed Object UNIT
Multiplicity 1
Description This parameter identifies the unit location as the slot number containing the hardware unit of BTS transport.
Range 1... 1
Units -
Formula for getting internal value
internal_value = gui_value
Default value -
Default value notes -
Related functions -
Modification Not modifiable
Related parameters -
Parameter relationships -
Related options -
Feature dependencies -
Interfaces • EM <-> FTM • RAC -> FTM • RAC <-> RACApp
References -
Validation pattern -
Table 392 unitId (Unit Identifier) (Cont.)
Parameter name Installed hardware unit type
Abbreviated name unitTypeActual
3GPP name -
Managed Object UNIT
Multiplicity 1
Table 393 unitTypeActual (Installed hardware unit type)
DN70577885 463
Flexi Transport Module Parameters UNIT Parameters
Id:0900d80580975ffbConfidential
Description This parameter shows the type of the hardware unit that is installed in the FTM slot.
Values are:
System Module Release 2:
FIIB: 472271A
FILB: 472294A
FTEB: 470156A
FTFA: 470134A
FTFB: 472036A
FTHA: 471522A
FTIA: 471025A
FTIB: 471720A
FTJA: 471248A
FTLB: 471984A
FTOA: 470133A
FTPB: 470137A
System Module Release 3:
FSM: Outdoor System Module
FSI: Indoor System Module
FTIF: 472311A
FIIF: 472355A
Flexi BTS support:
FQGA:472467A
Range 7
Units characters
Formula for getting internal value
internal_value = gui_value
Default value -
Default value notes -
Related functions -
Modification Not modifiable
Related parameters -
Parameter relationships -
Related options • RAN1299 BTS Auto Configuration
Feature dependencies -
Interfaces • FTM -> EM • FTM -> RAC
Table 393 unitTypeActual (Installed hardware unit type) (Cont.)
464 DN70577885
Flexi Transport Module Parameters
Id:0900d80580975ffbConfidential
UNIT Parameters
49.4 unitTypeExpected (Expected hardware unit type)
References -
Validation pattern -
Table 393 unitTypeActual (Installed hardware unit type) (Cont.)
Parameter name Expected hardware unit type
Abbreviated name unitTypeExpected
3GPP name -
Managed Object UNIT
Multiplicity 1
Description This parameter specifies the type of the hardware unit that is expected to be installed in the FTM slot.
Values are:
System Module Release 2:
FIIB: 472271A
FILB: 472294A
FTEB: 470156A
FTFA: 470134A
FTFB: 472036A
FTHA: 471522A
FTIA: 471025A
FTIB: 471720A
FTJA: 471248A
FTLB: 471984A
FTOA: 470133A
FTPB: 470137A
System Module Release 3:
FSM: Outdoor System Module
FSI: Indoor System Module
FTIF: 472311A
FIIF: 472355A
Flexi BTS support:
FQGA:472467A
Table 394 unitTypeExpected (Expected hardware unit type)
DN70577885 465
Flexi Transport Module Parameters UNIT Parameters
Id:0900d80580975ffbConfidential
Range 470137A (0), 470156A (1), 470134A (2), 471522A (3), 471025A (4), 471720A (5), 471248A (6), 470133A (7), 471984A (8), 472036A (9), 472271A (10), 472294A (11) for WN7.0 1.0;
470137A (0), 470156A (1), 470134A (2), 471522A (3), 471025A (4), 471720A (5), 471248A (6), 470133A (7), 471984A (8), 472036A (9), 472271A (10), 472294A (11), FSM (12), FSI (14), 472311A (16), 472355A (17), 472467A (18) for WN7.0 2.0
Units -
Formula for getting internal value
gui ==> internal
470137A ==> 0
470156A ==> 1
470134A ==> 2
471522A ==> 3
471025A ==> 4
471720A ==> 5
471248A ==> 6
470133A ==> 7
471984A ==> 8
472036A ==> 9
472271A ==> 10
472294A ==> 11
FSM ==> 12
FSI ==> 14
472311A ==> 16
472355A ==> 17
472467A ==> 18
Default value -
Default value notes -
Related functions -
Modification On-Line
Related parameters -
Parameter relationships -
Related options • RAN1299 BTS Auto Configuration
Feature dependencies -
Table 394 unitTypeExpected (Expected hardware unit type) (Cont.)
466 DN70577885
Flexi Transport Module Parameters
Id:0900d80580975ffbConfidential
UNIT Parameters
Interfaces • EM <-> FTM • RAC <-> FTM • RAC <-> RACApp
References -
Validation pattern -
Table 394 unitTypeExpected (Expected hardware unit type) (Cont.)
DN70577885 467
Flexi Transport Module Parameters VCCT Parameters
Id:0900d80580975ffbConfidential
50 VCCT Parameters
50.1 VCI (Virtual Channel Identifier)
50.2 VPI (Virtual Path Identifier)
Parameter name Virtual Channel Identifier
Abbreviated name VCI
3GPP name -
Managed Object VCCT
Multiplicity 1
Description Virtual Channel Identifier.
Range 32... 4095
Units -
Formula for getting internal value
internal_value = gui_value
Default value -
Default value notes -
Related functions -
Modification Not modifiable
Related parameters -
Parameter relationships -
Related options -
Feature dependencies -
Interfaces • FTM -> EM • FTM -> RAC
References -
Validation pattern -
Table 395 VCI (Virtual Channel Identifier)
Parameter name Virtual Path Identifier
Abbreviated name VPI
3GPP name -
Managed Object VCCT
Multiplicity 1
Description Virtual Path Identifier.
Table 396 VPI (Virtual Path Identifier)
468 DN70577885
Flexi Transport Module Parameters
Id:0900d80580975ffbConfidential
VCCT Parameters
50.3 interfaceNumber (Interface Number)
Range 0... 255
Units -
Formula for getting internal value
internal_value = gui_value
Default value -
Default value notes -
Related functions -
Modification Not modifiable
Related parameters -
Parameter relationships -
Related options -
Feature dependencies -
Interfaces • FTM -> EM • FTM -> RAC
References -
Validation pattern -
Table 396 VPI (Virtual Path Identifier) (Cont.)
Parameter name Interface Number
Abbreviated name interfaceNumber
3GPP name -
Managed Object VCCT
Multiplicity 1
Description Defines the location of the physical interface on the unit.
The value range depends on the unit type.
FTEB, FTPB, FTIF, FIIF: 1..8
FIIB, FILB, FTIA, FTIB, FTJA, FTLB: 1..4
FTFB, FTFA, FTHA: 1..16
In case of Inverse Multiplexing for ATM (IMA) the value range is: 33..75.
For ATM over Ethernet, the value is always: 76.
Range 1... 76
Units -
Table 397 interfaceNumber (Interface Number)
DN70577885 469
Flexi Transport Module Parameters VCCT Parameters
Id:0900d80580975ffbConfidential
50.4 trafficDescriptorId (Traffic Descriptor Pointer)
Formula for getting internal value
internal_value = gui_value
Default value -
Default value notes -
Related functions -
Modification Not modifiable
Related parameters -
Parameter relationships -
Related options -
Feature dependencies -
Interfaces • FTM -> EM • FTM -> RAC
References -
Validation pattern -
Table 397 interfaceNumber (Interface Number) (Cont.)
Parameter name Traffic Descriptor Pointer
Abbreviated name trafficDescriptorId
3GPP name -
Managed Object VCCT
Multiplicity 1
Description This parameter points to the instance of the ATM traffic descriptor (TRDE) that contains the peak cell rate (PCR) settings for this virtual channel.
The value of the parameter is a number above 100. This references the identifier of the TRDE managed object instance, e.g. TRDE-104.
The traffic descriptor managed object instance must have been created before it can be referenced by this parameter.
Range 100... 9999999999
Units -
Formula for getting internal value
internal_value = gui_value
Default value -
Default value notes -
Table 398 trafficDescriptorId (Traffic Descriptor Pointer)
470 DN70577885
Flexi Transport Module Parameters
Id:0900d80580975ffbConfidential
VCCT Parameters
50.5 unitNumber (Unit Number)
Related functions -
Modification On-Line
Related parameters -
Parameter relationships -
Related options -
Feature dependencies -
Interfaces • EM <-> FTM • RAC <-> FTM • RAC <-> RACApp
References -
Validation pattern -
Table 398 trafficDescriptorId (Traffic Descriptor Pointer) (Cont.)
Parameter name Unit Number
Abbreviated name unitNumber
3GPP name -
Managed Object VCCT
Multiplicity 1
Description Specifies the location of the unit. In this release it is always 1.
Range 1... 1
Units -
Formula for getting internal value
internal_value = gui_value
Default value -
Default value notes -
Related functions -
Modification Not modifiable
Related parameters -
Parameter relationships -
Related options -
Feature dependencies -
Interfaces • FTM -> EM • FTM -> RAC
Table 399 unitNumber (Unit Number)
DN70577885 471
Flexi Transport Module Parameters VCCT Parameters
Id:0900d80580975ffbConfidential
50.6 vcCTPId (Virtual Channel Identifier (VCI))
References -
Validation pattern -
Table 399 unitNumber (Unit Number) (Cont.)
Parameter name Virtual Channel Identifier (VCI)
Abbreviated name vcCTPId
3GPP name -
Managed Object VCCT
Multiplicity 1
Description Naming attribute (relative to Virtual Path).
The value is the same as the attribute VCI
Range 32... 4095
Units -
Formula for getting internal value
internal_value = gui_value
Default value -
Default value notes -
Related functions -
Modification Not modifiable
Related parameters VCI of VCCT
Parameter relationships The value must be the same as the attribute VCI
Related options -
Feature dependencies -
Interfaces • EM <-> FTM • RAC -> FTM • RAC <-> RACApp
References -
Validation pattern -
Table 400 vcCTPId (Virtual Channel Identifier (VCI))
472 DN70577885
Flexi Transport Module Parameters
Id:0900d80580975ffbConfidential
VCTT Parameters
51 VCTT Parameters
51.1 VCI (Virtual Channel Identifier)
51.2 VPI (Virtual Path Identifier)
Parameter name Virtual Channel Identifier
Abbreviated name VCI
3GPP name -
Managed Object VCTT
Multiplicity 1
Description Virtual Channel Identifier.
Range 32... 4095
Units -
Formula for getting internal value
internal_value = gui_value
Default value -
Default value notes -
Related functions -
Modification Not modifiable
Related parameters -
Parameter relationships -
Related options -
Feature dependencies -
Interfaces • FTM -> EM • FTM -> RAC
References -
Validation pattern -
Table 401 VCI (Virtual Channel Identifier)
Parameter name Virtual Path Identifier
Abbreviated name VPI
3GPP name -
Managed Object VCTT
Multiplicity 1
Description Virtual Path Identifier.
Table 402 VPI (Virtual Path Identifier)
DN70577885 473
Flexi Transport Module Parameters VCTT Parameters
Id:0900d80580975ffbConfidential
51.3 aalProfilePtr (ATM Adaptation Layer (AAL) Profile Pointer)
Range 0... 255
Units -
Formula for getting internal value
internal_value = gui_value
Default value -
Default value notes -
Related functions -
Modification Not modifiable
Related parameters -
Parameter relationships -
Related options -
Feature dependencies -
Interfaces • FTM -> EM • FTM -> RAC
References -
Validation pattern -
Table 402 VPI (Virtual Path Identifier) (Cont.)
Parameter name ATM Adaptation Layer (AAL) Profile Pointer
Abbreviated name aalProfilePtr
3GPP name -
Managed Object VCTT
Multiplicity 1
Description Specifies for which AAL type the virtual channel (VCCT) is terminated.
Supported types are AAL2-1 (AAL2 user traffic) and AAL5-1 (IP over ATM connections, AAL2 signal-ling).
Range AAL2-1 (1), AAL5-1 (2)
Units -
Formula for getting internal value
gui ==> internal
AAL2-1 ==> 1
AAL5-1 ==> 2
Default value -
Table 403 aalProfilePtr (ATM Adaptation Layer (AAL) Profile Pointer)
474 DN70577885
Flexi Transport Module Parameters
Id:0900d80580975ffbConfidential
VCTT Parameters
51.4 interfaceNumber (Interface Number)
Default value notes -
Related functions -
Modification On-Line
Related parameters -
Parameter relationships -
Related options -
Feature dependencies -
Interfaces • EM <-> FTM • RAC <-> FTM • RAC <-> RACApp
References -
Validation pattern -
Table 403 aalProfilePtr (ATM Adaptation Layer (AAL) Profile Pointer) (Cont.)
Parameter name Interface Number
Abbreviated name interfaceNumber
3GPP name -
Managed Object VCTT
Multiplicity 1
Description Defines the location of the physical interface on the unit.
The value range depends on the unit type.
FTEB, FTPB, FTIF, FIIF: 1..8
FIIB, FILB, FTIA, FTIB, FTJA, FTLB: 1..4
FTFB, FTFA, FTHA: 1..16
In case of Inverse Multiplexing for ATM (IMA) the value range is: 33..75.
For ATM over Ethernet, the value is always: 76.
Range 1... 76
Units -
Formula for getting internal value
internal_value = gui_value
Default value -
Default value notes -
Related functions -
Table 404 interfaceNumber (Interface Number)
DN70577885 475
Flexi Transport Module Parameters VCTT Parameters
Id:0900d80580975ffbConfidential
51.5 unitNumber (Unit Number)
Modification Not modifiable
Related parameters -
Parameter relationships -
Related options -
Feature dependencies -
Interfaces • FTM -> EM • FTM -> RAC
References -
Validation pattern -
Table 404 interfaceNumber (Interface Number) (Cont.)
Parameter name Unit Number
Abbreviated name unitNumber
3GPP name -
Managed Object VCTT
Multiplicity 1
Description Specifies the location of the unit. In this release it is always 1.
Range 1... 1
Units -
Formula for getting internal value
internal_value = gui_value
Default value -
Default value notes -
Related functions -
Modification Not modifiable
Related parameters -
Parameter relationships -
Related options -
Feature dependencies -
Interfaces • FTM -> EM • FTM -> RAC
References -
Validation pattern -
Table 405 unitNumber (Unit Number)
476 DN70577885
Flexi Transport Module Parameters
Id:0900d80580975ffbConfidential
VCTT Parameters
51.6 vcTTPId (Virtual Channel Trail Termination Point Identi-fier)
Parameter name Virtual Channel Trail Termination Point Identifier
Abbreviated name vcTTPId
3GPP name -
Managed Object VCTT
Multiplicity 1
Description Naming attribute
The object is identified by
- unitNumber(unit#)
- interfaceNumber (if#, imag# or pw#)
- virtual path identifier (vpi#)
- virtual channel identifier (vci#)
Possible formats (examples in parentheses):
- unit#-if#-vpi#vci# (2-8-000C0)
- slot#-imag#-vpi#vci# (2-34-00210)
Value ranges:
- unit#: 1
- if#: 1..16 (1 or 2 digits)
- imag#: 33..75 (2 digits)
- pw#: 76
- vpi#: 00..FF (hexadecimal number, 2 digits)
- vci#: 000..FFF (hexadecimal number, 3 digits)
Range 9...10
Units characters
Formula for getting internal value
internal_value = gui_value
Default value -
Default value notes -
Related functions -
Modification Not modifiable
Related parameters VCI of VCTT
VPI of VCTT
interfaceNumber of VCTT
unitNumber of VCTT
Table 406 vcTTPId (Virtual Channel Trail Termination Point Identifier)
DN70577885 477
Flexi Transport Module Parameters VCTT Parameters
Id:0900d80580975ffbConfidential
Parameter relationships The VCTT id is composed of the values of these other attributes.
Related options -
Feature dependencies -
Interfaces • EM <-> FTM • RAC -> FTM • RAC <-> RACApp
References -
Validation pattern -
Table 406 vcTTPId (Virtual Channel Trail Termination Point Identifier) (Cont.)
478 DN70577885
Flexi Transport Module Parameters
Id:0900d80580975ffbConfidential
VPCT Parameters
52 VPCT Parameters
52.1 VPI (Virtual Path Identifier)
52.2 interfaceNumber (Interface Number)
Parameter name Virtual Path Identifier
Abbreviated name VPI
3GPP name -
Managed Object VPCT
Multiplicity 1
Description Virtual Path Identifier.
Range 0... 255
Units -
Formula for getting internal value
internal_value = gui_value
Default value -
Default value notes -
Related functions -
Modification Not modifiable
Related parameters -
Parameter relationships -
Related options -
Feature dependencies -
Interfaces • FTM -> EM • FTM -> RAC
References -
Validation pattern -
Table 407 VPI (Virtual Path Identifier)
Parameter name Interface Number
Abbreviated name interfaceNumber
3GPP name -
Managed Object VPCT
Multiplicity 1
Table 408 interfaceNumber (Interface Number)
DN70577885 479
Flexi Transport Module Parameters VPCT Parameters
Id:0900d80580975ffbConfidential
52.3 trafficDescriptorId (Traffic Descriptor Pointer)
Description Defines the location of the physical interface on the unit.
The value range depends on the unit type.
FTEB, FTPB, FTIF, FIIF: 1..8
FIIB, FILB, FTIA, FTIB, FTJA, FTLB: 1..4
FTFB, FTFA, FTHA: 1..16
In case of Inverse Multiplexing for ATM (IMA) the value range is: 33..75.
For ATM over Ethernet, the value is always: 76.
Range 1... 76
Units -
Formula for getting internal value
internal_value = gui_value
Default value -
Default value notes -
Related functions -
Modification Not modifiable
Related parameters -
Parameter relationships -
Related options -
Feature dependencies -
Interfaces • FTM -> EM • FTM -> RAC
References -
Validation pattern -
Table 408 interfaceNumber (Interface Number) (Cont.)
Parameter name Traffic Descriptor Pointer
Abbreviated name trafficDescriptorId
3GPP name -
Managed Object VPCT
Multiplicity 1
Table 409 trafficDescriptorId (Traffic Descriptor Pointer)
480 DN70577885
Flexi Transport Module Parameters
Id:0900d80580975ffbConfidential
VPCT Parameters
52.4 unitNumber (Unit Number)
Description This parameter points to the instance of the ATM traffic descriptor (TRDE) that contains the peak cell rate (PCR) settings for this virtual path.
The value of the parameter is a number above 100. This references the identifier of the TRDE managed object instance, e.g. TRDE-104.
The traffic descriptor managed object instance must have been created before it can be referenced by this parameter.
Range 100... 9999999999
Units -
Formula for getting internal value
internal_value = gui_value
Default value -
Default value notes -
Related functions -
Modification On-Line
Related parameters -
Parameter relationships -
Related options -
Feature dependencies -
Interfaces • EM <-> FTM • RAC <-> FTM • RAC <-> RACApp
References -
Validation pattern -
Table 409 trafficDescriptorId (Traffic Descriptor Pointer) (Cont.)
Parameter name Unit Number
Abbreviated name unitNumber
3GPP name -
Managed Object VPCT
Multiplicity 1
Description Specifies the location of the unit. In this release it is always 1.
Range 1... 1
Table 410 unitNumber (Unit Number)
DN70577885 481
Flexi Transport Module Parameters VPCT Parameters
Id:0900d80580975ffbConfidential
52.5 vpCTPId (Virtual Path Identifier (VPI))
Units -
Formula for getting internal value
internal_value = gui_value
Default value -
Default value notes -
Related functions -
Modification Not modifiable
Related parameters -
Parameter relationships -
Related options -
Feature dependencies -
Interfaces • FTM -> EM • FTM -> RAC
References -
Validation pattern -
Table 410 unitNumber (Unit Number) (Cont.)
Parameter name Virtual Path Identifier (VPI)
Abbreviated name vpCTPId
3GPP name -
Managed Object VPCT
Multiplicity 1
Description Specifies a virtual path on an ATM interface (TCTT) and serves as naming attribute for this object.
The value range is defined in the access profile of the ATM interface with the attribute maxNumVPIB-itsSupported.
Range 0... 255
Units -
Formula for getting internal value
internal_value = gui_value
Default value -
Default value notes -
Related functions -
Modification Not modifiable
Table 411 vpCTPId (Virtual Path Identifier (VPI))
482 DN70577885
Flexi Transport Module Parameters
Id:0900d80580975ffbConfidential
VPCT Parameters
Related parameters -
Parameter relationships -
Related options -
Feature dependencies -
Interfaces • EM <-> FTM • RAC -> FTM • RAC <-> RACApp
References -
Validation pattern -
Table 411 vpCTPId (Virtual Path Identifier (VPI)) (Cont.)
DN70577885 483
Flexi Transport Module Parameters VPTT Parameters
Id:0900d80580975ffbConfidential
53 VPTT Parameters
53.1 VPI (Virtual Path Identifier)
53.2 interfaceNumber (Interface Number)
Parameter name Virtual Path Identifier
Abbreviated name VPI
3GPP name -
Managed Object VPTT
Multiplicity 1
Description Virtual Path Identifier.
Range 0... 255
Units -
Formula for getting internal value
internal_value = gui_value
Default value -
Default value notes -
Related functions -
Modification Not modifiable
Related parameters -
Parameter relationships -
Related options -
Feature dependencies -
Interfaces • FTM -> EM • FTM -> RAC
References -
Validation pattern -
Table 412 VPI (Virtual Path Identifier)
Parameter name Interface Number
Abbreviated name interfaceNumber
3GPP name -
Managed Object VPTT
Multiplicity 1
Table 413 interfaceNumber (Interface Number)
484 DN70577885
Flexi Transport Module Parameters
Id:0900d80580975ffbConfidential
VPTT Parameters
53.3 unitNumber (Unit Number)
Description Defines the location of the physical interface on the unit.
The value range depends on the unit type.
FTEB, FTPB, FTIF, FIIF: 1..8
FIIB, FILB, FTIA, FTIB, FTJA, FTLB: 1..4
FTFB, FTFA, FTHA: 1..16
In case of Inverse Multiplexing for ATM (IMA) the value range is: 33..75.
For ATM over Ethernet, the value is always: 76.
Range 1... 76
Units -
Formula for getting internal value
internal_value = gui_value
Default value -
Default value notes -
Related functions -
Modification Not modifiable
Related parameters -
Parameter relationships -
Related options -
Feature dependencies -
Interfaces • FTM -> EM • FTM -> RAC
References -
Validation pattern -
Table 413 interfaceNumber (Interface Number) (Cont.)
Parameter name Unit Number
Abbreviated name unitNumber
3GPP name -
Managed Object VPTT
Multiplicity 1
Description Specifies the location of the unit. In this release it is always 1.
Range 1... 1
Table 414 unitNumber (Unit Number)
DN70577885 485
Flexi Transport Module Parameters VPTT Parameters
Id:0900d80580975ffbConfidential
53.4 vpTTPId (Virtual Path Trail Termination Point Identifier)
Units -
Formula for getting internal value
internal_value = gui_value
Default value -
Default value notes -
Related functions -
Modification Not modifiable
Related parameters -
Parameter relationships -
Related options -
Feature dependencies -
Interfaces • FTM -> EM • FTM -> RAC
References -
Validation pattern -
Table 414 unitNumber (Unit Number) (Cont.)
Parameter name Virtual Path Trail Termination Point Identifier
Abbreviated name vpTTPId
3GPP name -
Managed Object VPTT
Multiplicity 1
Table 415 vpTTPId (Virtual Path Trail Termination Point Identifier)
486 DN70577885
Flexi Transport Module Parameters
Id:0900d80580975ffbConfidential
VPTT Parameters
Description Specifies the termination of the virtual path.
The object is identified by
- unitNumber(unit#)
- interfaceNumber (if#, imag#)
- virtual path identifier (vpi#)
- pw tunnel id (pwt#)
Possible formats:
- unit#-if#-vpi#
- unit#-imag#-vpi#
- unit#-pwt#-vpi#
Value ranges:
unit#: 1
if#: 1..16
imag#: 33..75
vpi#: 0..255
pwt#: 76
Range 5...8
Units characters
Formula for getting internal value
internal_value = gui_value
Default value -
Default value notes -
Related functions -
Modification Not modifiable
Related parameters VPI of VPTT - The value of parameter VPI is contained in the value of parame-ter vpTTPId.
interfaceNumber of VPTT - The value of parameter interfaceNumber is contained in the value of parameter vpTTPId.
unitNumber of VPTT - The value of parameter unitNumber is contained in the value of parameter vpTTPId.
Parameter relationships The VPTT id is composed of the values of these other attributes
Related options -
Feature dependencies -
Table 415 vpTTPId (Virtual Path Trail Termination Point Identifier) (Cont.)
DN70577885 487
Flexi Transport Module Parameters VPTT Parameters
Id:0900d80580975ffbConfidential
Interfaces • EM <-> FTM • RAC -> FTM • RAC <-> RACApp
References -
Validation pattern -
Table 415 vpTTPId (Virtual Path Trail Termination Point Identifier) (Cont.)