INSTALLATION INSTRUCTIONS

M2-1120FLEETWOOD CROSS HANDLE 3-HOLE BASIN MIXER

M2-1121FLEETWOOD LEVER 3-HOLE BASIN MIXER

M2-1121M2-1120

2

Dimensions in Inches (& Millimetres)

Whilst every effort is made to ensure accuracy, design and dimensions are subject tochange without notice as part of the company’s product development process.

M2-1121

M2-1120

7 7/8"(200mm)

7 1/

16"

(178

.7m

m)

10"(254mm)

1/16

"~1

3/16

"(1

mm

)~(3

0mm

)

2 15

/16"

(74.

9mm

)

1 3/

16"

(30m

m)

2-9/16-24UNEF-2A

2-G

1/2

Ø2 3/16"(Ø55mm)

Ø2 3/16"(Ø55mm)

Ø2 3/16"(Ø55mm)

3 1/8"(80mm)

3 1/

8"(8

0.1m

m)

2-1/2-14NPSM-2A

9 7/

16"

(240

mm

)

4"

(102

mm

)

Ø2 3/16"(Ø55mm)

2 15

/16"

(75m

m)

2 15

/16"

(75m

m)

1/16

"~1

3/16

"(1

mm

)~(3

0mm

)

3 1/

8"(8

0mm

) 1 15

/16"

(50m

m)

2-1/2-14NPSM-2A

2-9/

16-2

4UNEF

-2A

4"(1

02m

m)

Ø2 3/16"(Ø55mm)

Ø2 3/16"(Ø55mm)

2-G

1/2

6"(152mm)

4 13

/16"

(122

.7m

m)

9 7/

16"

(240

mm

)

1/16

"~1

3/16

"(1

mm

)~(3

0mm

)

3

What you need to know

Adjustable WrenchGroove Joint PliersHacksawPhillips ScrewdriverPipe TapeSpatulaSpirit Level

Your new bathroom faucet is designed for yearsof trouble-free performance.

Keep it looking new by cleaning it periodically witha soft cloth. Avoid abrasive cleaners, wire wool andharsh chemicals as these will dull the finish andvoid your warranty.

If you are soldering during faucet installation,remove cartridges, seats, gaskets and washersprior to applying flame, otherwise you will voidthe warranty.

Cover drain openings to avoid losing small parts.

When cutting or soldering pipe, use safety glassesto protect your eyes.

Correct installation may vary depending on previous faucet installation. All necessary supplies required forfaucet installation are not included, but may be found where plumbing supplies are sold. It is suggested thatIAPMO and/or CSA approved plumbing supplies are used during installation.

Prior to beginning installation. turn off the cold andhot water lines and open the old faucet to releasebuilt-up pressure.

Overtightening nuts may cause damage.

Wrap all threaded connections with pipe tape available at your local plumbing supply store. Always wrap in a clockwise direction. The fittings should be installed by a state-licenced plumber.

Tools: Maintenance

Safety Tips

Things You May Need

Important Points

Standards Flow Rate

Please note : Final achievable flow rate is dependent on the outlets fitted, see relevant outlets (spouts, roses, sprays) for fullyassembled product flow rate.

IAPMO/cUPC Listed (all variants)Meets NSF 61-9 (all variants)Meets A112.18.1 (all variants)ADA Compliant (M2-1121only)

0

1.2

1.4

20 40 60 80PSI

4

Steps 1-4

Installation ProcedureLefroy Brooks always recommends that plumbing products be installed by a licensed professional.Shut off main water supply before installation.

4

1

2

3Install left handle assembly, headwork cover and side body.

Install other handle assembly, headwork cover and side body.

Connect flexible hoses. Alternative nuts are supplied in case you want to connect copper pipes instead.

Fit spout and install the connector assem-bly.

43

1 2

Set Screw

Alternative nuts

5

Steps 5

Installation ProcedureLefroy Brooks always recommends that plumbing products be installed by a licensed professional.Shut off main water supply before installation.

5 Remove aerator and turn on water to remove any left over debris. Re-assemble aerator.

5

Warning! When installing flexible hose, please notice:1. There should be no torsion or deformation2. Do not fold into a V or L shape.3. Do not use if there is any crack or deformation.

6

Exploded View

Parts List

M2-1120

1 Spout assembly (139376W)2 Oil-seal (010519N)3 Aerator insert (553661N)4 Aerator housing (305856-54)5 Handle (029685H-T)6 Set screw (075209)7 O-ring (004026N)8 Canopy (000113)9 Escutcheon (071326)10 O-ring (004072N)11 Washer (013797)

12 Oil-seal (058094)13 Washer (013006)14 Nut (009015)15 Connector (015004W)16 Handle (029685C-T)17 Canopy (018295)18 Washer (013570)19 Screw (008486)20 Clip (012242)21 Stem extension (110409)22 Adaptor (057507)

23 Cartridge (507907N)24 Escutcheon (071473)25 O-ring (004617)26 Oil-seal (010017)27 Washer (013158)28 Nut (009834)29 Body (061893W)30 Flexible hose (105750W)31 Allen key (031000)32 Alternative nuts (504003)

1

2

3

4

6

7

8

9

10

11

12

13

14

15

17

20

21

23

24

25

26

27

28

29

30

19

32

16

5

31

22

18

7

Parts List

M2-1121

1 Spout assembly (139376W)2 Oil-seal (010519N)3 Aerator insert (553661N)4 Aerator housing (305856-54)5 Handle (029686H-T)6 Cartridge ( H ) (507175N)7 O-ring (004026N)8 Set screw (075209)9 Canopy (000113)10 Escutcheon (071326)11 O-ring (004072N)

12 Washer (013797)13 Oil-seal (058094)14 Washer (013006)15 Nut (009015)16 Connector (015004W)17 Body (061893W)18 Handle (029686C-T)19 Canopy (018295)20 Washer (013570)21 Screw (008486)22 Clip (012242)

23 Stem extension (110409)24 Adaptor (057507)25 Cartridge ( C ) (507176N)26 Escutcheon (071473)27 O-ring (004617)28 Oil-seal (010017)29 Washer (013158)30 Nut (009834)31 Alternative nuts (504003)32 Flexible hose (105750W)33 Allen key (031000)

19

2

3

4

6

18

7

21

9

10

11

12

13

14

15

16

17

22

23

25

26

27

28

29

30

5

32

31

1

824

20

33

For additional assistance or service call

718-302-52929am to 5pm EST Monday to Friday

LEFROY BROOKS INC, 1828 TROUTMAN STREET, RIDGEWOOD, NY, 11385TELEPHONE: 718-302-5292. FAX: 718-302-4177

The use of trademarks, product design and artwork is subject to licence or agreement with LBIP Ltd. The designregistrations, trademark registrations and copyrights are protected by law and the use or reproduction outside the terms of an agreement is prohibited.

The right to modify designs and dimensions is reserved. Christo Lefroy Brooks is a member of ACID (Anti Copying in Design).

© LBIP LTD 2012

www.lefroybrooks.com