Upload
rao-dheeru
View
214
Download
0
Embed Size (px)
Citation preview
7/28/2019 Fixed Timers
1/3
Timer NameDescription Value
T100 RADIO-LINK-TIMEOUT
Detects the presence of the radio link by detectingSACCH frames every 480 ms.
4 SACCH
multiframes. That
is 1.92 seconds ifthe SACCH is
completely absent.
T200 Data link
timer
Used for re-transmission on the data link. The
value varies depending on the message type.155 ms for FACCH
T301 Alerting
(ringing) timer
Timer used to limit the amount of time a user has
to answer a call.20 seconds
T303 Mobility
Management
connection timer
Time the network waits after sending a CMSERVICE REQUEST until receiving a response.
This occurs before initiating call clearing
procedures towards the MS.
10 seconds
T305 Release
timer
Time the network waits after transmitting a
DISCONNECT message until receiving a
RELEASE message.10 seconds
T306 In-band
tones release timer
Time the network waits after transmitting a
DISCONNECT message while in-bandtones/announcements are provided, until receiving
a RELEASE message.
10 seconds
T308 Releasetimer
Time the network waits after sending a RELEASE
message until receiving a RELEASE COMPLETE
message. This occurs before re-transmitting theRELEASE or releasing the Mobility Management
connection.
10 seconds
T310 Call
proceeding timer
Time the network waits after receiving a CALL
CONFIRMED message until receiving a
ALERTING, CONNECT, or DISCONNECTmessage before initiating clearing procedurestowards the MS.
10 seconds
T313 Connect
acknowledge timer
Time the network waits after transmitting aCONNECT message until receiving the
CONNECT ACKNOWLEDGE message before
performing clearing procedures with the MS.
10 seconds
7/28/2019 Fixed Timers
2/3
Timer NameDescription Value
T323 Modify
complete timer
Time the network waits after sending a MODIFY
message during call mode changes, until receiving
a MODIFY COMPLETE or MODIFY REJECTmessage before initiating call clearing procedures.
10 seconds
T3101 Immediate
assignment timer
Time the network waits after sending theIMMEDIATE ASSIGNMENT or IMMEDIATE
ASSIGNMENT EXTENDED message until the
main signalling link is established before releasingthe newly allocated channels.
1 second
T3103 Handover
timer
Time the network waits after transmitting aHANDOVER COMMAND message until
receiving HANDOVER COMPLETE orHANDOVER FAILURE or the MS re-establishesthe call before the old channels are released. If the
timer expires and the network has not received a
correctly decoded L2 (format A or B) or TCHframe, then the newly allocated channels are
released.
2 seconds
T3105 Physicalinformation
repetition timer
Time the network waits after sending the
PHYSICAL INFORMATION message until
receiving a correctly decoded L2 (format A or B)
or TCH frame. This occur before re-transmitting
the PHYSICAL INFORMATION message orreleasing the newly allocated channels.
50 ms
T3107 Channel
assignment timer
Time the network waits after transmitting an
ASSIGNMENT COMMAND message untilreceiving the ASSESSMENT FAILURE message
or the MS re-establishes the call before releasing
the old and the new channels.
3 seconds
T3109 Signalling
disconnection
timer
Time the network waits after sending the
CHANNEL RELEASE message before
disconnecting the signalling link.
5 seconds
T3111 Channel
deactivation afterdisconnection
timer
Time the network waits after disconnecting thesignalling link before deactivating the channel.
500 ms
7/28/2019 Fixed Timers
3/3
Timer NameDescription Value
T3113 Pagingtimer
Time the network waits after transmitting the
PAGING REQUEST message until receiving the
PAGING RESPONSE message. This occursbefore re-transmitting the PAGING REQUEST (if
the maximum number of re-transmissions have not
been exceeded).
5 seconds
T3212 Locationupdate timer
The location update timer is set to zero, periodic
location update by the MS are disabled. If the MScamps to the BCH and decodes a new MCC or
MNC from the one it last camped on, it should
perform a location update.
zero = infinite time
T3250 TMSIreallocation timer
Time the network waits after sending the TMSI
REALLOCATION COMMAND until receiving
TMSI REALLOCATION COMPLETE. Thisoccurs before aborting the procedure and releasing
the Radio Resource connection.
5 seconds
T3260
Authenticationresponse timer
Time the network waits after an
AUTHENTICATION REQUEST until receiving
AUTHENTICATION RESPONSE. This occursbefore aborting the procedure and releasing the
Radio Resource connection.
5 seconds