1
IS-ROS4100-062207 Thank you for purchasing one of Advanced Technology Inc.’s SHOTFORCE COMPONENTS! Please fill out the enclosed Unconditional Lifetime Warranty card and mail it within 30 days of purchase. ASSEMBLY INSTRUCTIONS MAKE SURE YOUR FIREARM IS UNLOADED BEFORE STARTING! ROSSI INSTALLATION INSTRUCTIONS STEP 1 Remove recoil pad by removing two screws from Buttstock STEP 2 Use #10mm or #13mm metric socket with extension to remove stock bolt from inside opening in rear of stock. STEP 3 New stock bolt will be either an M6 or M8 bolt. Select size of mounting bolt by hand starting each supplied bolt into tapped hole in receiver. STEP 4 Drop stock bolt with M8 washer into the end of the SHOTFORCE buttstock, place adapter over exit side of screw, align mounting screw with hole in receiver, and use long Phillips screwdriver to secure buttstock to receiver. NOTE: For 12/20ga shotgun: Collapsible stock must be fixed in second position using a long fastener with nut to comply with Section 922 (R). TO REPLACE FOREND STEP 1 Remove existing forend by unscrewing sling swivel on bottom of Rossi forend. STEP 2 Rossi has two receiver widths. If you have a wide receiver: Your new SHOTFORCE Forend includes a Pronged Adapter for the wide receiver assembled on the forend. If you have a narrow width receiver: Remove the Pronged Adapter located at the rear of your Rossi forend by removing one screw. Use Dremel tool to remove the pin sticking up from the flat side of the Rossi Adapter (Surface must be flush with back face of adapter). Use a 5/32 diameter drill to drill a vertical hole at the center of the pin. (Smaller drill can be used first to center and locate hole position). On the curved side, use a tapered Dremel tool to countersink the 5/32 drilled hole so the head of the #6 screw is below the curved surface. Secure the Pronged Adapter to the SHOTFORCE forend by placing (1) #6 x 1/2”screw into the bottom center hole on the SHOTFORCE forend. STEP 3 Rossi barrels have two different forend mounting post locations. Place the SHOTFORCE forend beside your barrel to determine the location of the mounting post. If the mounting post is closer to the rear position of the forend, do not remove the front screw from the forend. If the mounting post is near to the front position of the forend, remove the front screw to eliminate interference with the mounting post. STEP 4 Align the rear of the SHOTFORCE forend with the front of the receiver and pivot the forend upwards into place. STEP 5 Secure the forend by installing the supplied M6 x 16mm screw into the mounting post projecting into the forend. CAUTION: Do not overtighten any screws. TACTICAL BUTTSTOCK SHOTFORCE Adapter M8 Washer M8 Phillips Bolt DELUXE HEATSHIELD RECOMMENDED FOR SMALL BARREL ROSSI GUNS M8 Washer M6 Phillips Bolt Front Position Rear Position TACTICAL FOREND SHOTFORCE Forend Adapter (included) M6 x 16mm Flathead Screw ROSSI Narrow Width Forend Adapter (2) #6 x 1/2” Phillips Head Screws (1) #6 x 1/2” Phillips Head Screw Rossi Products are manufactured in several different receiver/forend lengths and widths. This product retro-fits all Rossi rifle and shotgun styles. Congratulations on purchasing one of Advanced Technology, Inc’s ROSSI SHOTFORCE components. There are several combinations and additional components available. Check with your local retailer for more new, exciting accessories. Rossi 12GA (Shown with Recommended Deluxe Heatshield with Ghost Ring Sights) Rossi .410 (Shown with Recommended Deluxe Heatshield, Scope, and Bipod). Rossi .223 Rifle (Shown with Deluxe Heatshield with Ghost Ring Sights, Muzzle Mount, Laser) ROSSI STOCK WITH TACTICAL FOREND INSTALLATION INSTRUCTIONS PART# ROS4100 Fits: All Rossi Shotguns and Rifle Models TO REPLACE BUTTSTOCK

Fits: All Rossi Shotguns and Rifle Models PART# …media.midwayusa.com/pdf/reference/advanced_technology_rossi_stock...ROSSI INSTALLATION INSTRUCTIONS Step 1 Remove recoil pad by removing

Embed Size (px)

Citation preview

Page 1: Fits: All Rossi Shotguns and Rifle Models PART# …media.midwayusa.com/pdf/reference/advanced_technology_rossi_stock...ROSSI INSTALLATION INSTRUCTIONS Step 1 Remove recoil pad by removing

IS-ROS4100-062207

Thank you for purchasing one of Advanced Technology Inc.’s SHOTFORCE COMPONENTS! Please fill out the enclosed Unconditional Lifetime Warranty card and mail it within 30 days of purchase.

ASSEMBLY INSTRUCTIONS

MAKE SURE YOUR FIREARM IS UNLOADED BEFORE STARTING!ROSSI INSTALLATION INSTRUCTIONS

Step 1 RemoverecoilpadbyremovingtwoscrewsfromButtstockStep 2 Use#10mmor#13mmmetricsocketwithextensiontoremovestockboltfrominsideopeninginrearofstock.Step 3 NewstockboltwillbeeitheranM6orM8bolt.Selectsizeofmountingboltbyhandstartingeachsuppliedboltintotappedholeinreceiver.Step 4 DropstockboltwithM8washerintotheendoftheSHOTFORCEbuttstock,placeadapteroverexitsideofscrew,alignmountingscrewwithholeinreceiver,

anduselongPhillipsscrewdrivertosecurebuttstocktoreceiver.NOte: For12/20gashotgun:CollapsiblestockmustbefixedinsecondpositionusingalongfastenerwithnuttocomplywithSection922(R).

TO REPLACE FORENDStep 1 RemoveexistingforendbyunscrewingslingswivelonbottomofRossiforend.Step 2 Rossihastworeceiverwidths.Ifyouhaveawidereceiver:YournewSHOTFORCEForendincludesaProngedAdapterforthewidereceiverassembled

ontheforend.Ifyouhaveanarrowwidthreceiver:RemovetheProngedAdapterlocatedattherearofyourRossiforendbyremovingonescrew.UseDremeltooltoremovethepinstickingupfromtheflatsideoftheRossiAdapter(Surfacemustbeflushwithbackfaceofadapter).Usea5/32diameterdrilltodrillaverticalholeatthecenterofthepin.(Smallerdrillcanbeusedfirsttocenterandlocateholeposition).Onthecurvedside,useataperedDremeltooltocountersinkthe5/32drilledholesotheheadofthe#6screwisbelowthecurvedsurface.SecuretheProngedAdaptertotheSHOTFORCEforendbyplacing(1)#6x1/2”screwintothebottomcenterholeontheSHOTFORCEforend.

Step 3 Rossibarrelshavetwodifferentforendmountingpostlocations.PlacetheSHOTFORCEforendbesideyourbarreltodeterminethelocationofthemountingpost.Ifthemountingpostisclosertotherearpositionoftheforend,donotremovethefrontscrewfromtheforend.Ifthemountingpostisneartothefrontpositionoftheforend,removethefrontscrewtoeliminateinterferencewiththemountingpost.

Step 4 AligntherearoftheSHOTFORCEforendwiththefrontofthereceiverandpivottheforendupwardsintoplace.Step 5 SecuretheforendbyinstallingthesuppliedM6x16mmscrewintothemountingpostprojectingintotheforend.

CAUTION:Donotovertightenanyscrews.

TACTICAL BUTTSTOCK

SHOTFORCE Adapter

M8 Washer

M8 Phillips Bolt

DELUxE HEATSHIELD RECOMMENDED FOR SMALL BARREL ROSSI GUNS

M8 Washer M6 Phillips

Bolt

Front Position Rear Position

TACTICAL FORENDSHOTFORCEForend Adapter(included)

M6 x 16mmFlathead Screw

ROSSI Narrow WidthForend Adapter

(2) #6 x 1/2” Phillips Head Screws

(1) #6 x 1/2” Phillips Head Screw

Rossi Products are manufactured in several different receiver/forend lengths and widths. This product retro-fits all Rossi rifle and shotgun styles.

Congratulations on purchasing one of Advanced technology, Inc’s ROSSI SHOtFORCe components. there are several combinations and additional components available. Check with your local retailer for more new, exciting accessories.

Rossi 12GA

(Shown with Recommended Deluxe Heatshield with Ghost Ring Sights)

Rossi .410

(Shown with Recommended Deluxe Heatshield, Scope, and Bipod).

Rossi .223 Rifle (Shown with Deluxe Heatshield with Ghost Ring Sights, Muzzle Mount, Laser)

ROSSI STOCK WITH TACTICAL FOREND

INSTALLATION INSTRUCTIONSPART# ROS4100

Fits: All Rossi Shotguns and Rifle Models

TO REPLACE BUTTSTOCK