w h e r e i n n ova t i o n f l o w s

TM

www.euroflopumps.com

EUF/EUFS series

Fire Pump PSB Listed according to CP52(Singapore)

Australian Standard:AS 2941:2008Fixed Fire Protection Installation and Pumpset System

SETSCO Certification Body S-01 Terms and Conditions, Sept 2010

- 11 -

ANNEX 1: SPECIMEN OF LOGO and MARK

A) SETSCO (Registered) Logo

B) SETSCO Mark for Ready-Mixed Concrete

C) SETSCO Mark for Fire Safety Products

Remarks: YYYY – year of initial certification XXX – unique number A – site number

Cert No: RMC-YYYY-XXX-A

Cert No: FSP-YYYY-XXX

E.g. EUFS100/315 PBD DBXXXX XXX/XXX X XX XXXX

SeriesEUF = Bareshaft FirepumpsEUFS = High Pressure Series

Discharge Size

Impeller Nominal Size

Seal TypeP = Gland Packing

Impeller / Body Casing MaterialBC = Bronze impeller and Cast Iron BodyWW = Cast steel impeller and cast steel BodyBD = Bronze Impeller and Ductile Iron BodySC = SS304 impeller and Cast Iron BodySD = SS304 impeller and Ductile Iron Body

Special CodeDB = Double BearingOL = Oil LubricatorK6 = SS316 ShaftS4 = SS304 ShaftS1 = SS431 Shaft

IntroductionDescription:Volute casing centrifugal end suction pump with Back Pull-Out (BPO) feature, main dimensions and performance according to EN733/DIN24255/6 standards (EUF), ISO 2858/5199 (EUFS).

Flange : Std PN 16, PN 25, 40 Bar (optional) Materials : Cast Iron, Ductile Iron, Cast SteelMounting : Direct Coupled with Electric Motor or EngineDirection of Rotation : Clockwise as viewed from the drive sideMaterial :Casing : Ductile Iron, Cast Steel, Cast IronImpeller : BronzeShaft : SS420 optional AISI304 & AISI316Shaft Seal : Gland Packing

Operating Range :Flow Rate(Q) : up to 1100m3/hHead(H) : up to 290mSpeed : 2900 rpm (50Hz)Operating Temp. : -10 °C to 105 °C standard; Operating Pressure : 16 Bar (EUF) and 40 Bar (EUFS)

Application:Fire protection and fire fighting

w h e r e i n n o va t i o n f l o w s

TM

EUF/EUFS series

Coding System

w h e r e i n n o va t i o n f l o w s

TM

EUF/EUFS series

EUF Sectional Drawing

EUFS Sectional Drawing

Shaft Protection Sleeve (with Gland Packing Only)Replaceable Shaft Sleeves can be replaced due to damaged and also different metallurgy for various operational needs.

Ball bearingsHeavy Duty Deep Grooved Ball bearing are used to maintain rigidity and stability. This is further enhanced with a Double Roll Bearing located on the Non-Drive End to give additional support to the impeller and Seals due to the nature of operation.

Bearing HousingBack Pull-Out design allow removal of wet Ends from the casing without disturbing the pipe connection. A built-in oil reservoir designed for oil cooled bearing requirement as option.

Volute CasingSelf Venting design and cased in Ductile Cast Iron as standard. Maximum working pressure of 16 Bars.

ImpellerDynamically Balanced for smooth operation that improve mechanical durability for optimum usage and Hydraulically balanced by means of balancing holes to reduces turbulence and recirculation to ensure smooth performance across entire operating range.

Casing Wear RingsRenewable wear ring protects the casing from wear and allows for optimum efficiency at all times of the pump life and reduces maintenance cost, with a simple wear ring replacement.

Gland PackingGland Packing with Lantern Ring for proper cooling and Flushing during operation.

Shaft Protection Sleeve (with Gland Packing Only)Replaceable Shaft Sleeves can be replaced due to damaged and also different metallurgy for various operational needs.

Bearing HousingHeavy duty casting to reduce vibration and adding surfact are (Fins) to improve dissipating of heat from high speed operation to prolong bearing life

ImpellerDynamically Balanced for smooth operation that improve mechanical durability for optimum usage and Hydraulically balanced by means of balancing holes to reduces turbulence and recirculation to ensure smooth performance across entire operating range.

Gland PackingGland Packing with Lantern Ring for proper cooling and Flushing during operation.

Casing Wear RingDouble wear ring design allows for max. hydraulic performance and mechanical efficiency within the pumps and economical sacrificial wear part

Volute Casing Self-venting casing built for max allowable pressure of 25 bars with option for 40 bars 40 bars (shut off above 22bar, casting is center lined supported)

Ball BearingSKF roller bearing and angular contact bearing to handle both radial /axial load when operating less than ideal condition

Oil FlingerEUFS uses oil mist lubricating for better heat dissipation from the bearing for longer bearing live and improve mean Time Between Failure (MTBF )

w h e r e i n n o va t i o n f l o w s

TM

EUF/EUFS series

S/N Pump modelImpeller

Diameter (mm)

Duty PointDriver Power

(kw)Q (m3/h) Head (m) Power (kw) Efficiency (%)

1 EUF50-13 139 55 23.1 5.4 64.2 7.5

2 EUF50-16 174 60 35.9 8.6 68.1 11.0

3 EUF50-20 214 55 58.3 14.1 61.9 18.5

4 EUF50-26 264 80 86.8 30.2 62.4 37.0

5 EUF50-32 329 80 137.0 54.0 55.8 75.0

6 EUF65-16 174 90 36.3 12.0 74.0 15.0

7 EUF65-20 214 110 55.4 23.3 71.1 30.0

8 EUF65-26 264 110 93.5 42.9 65.3 55.0

9 EUF65-32 329 110 141.0 68.9 61.5 90.0

10 EUF80-16 174 150 34.5 18.5 76.3 22.0

11 EUF80-20 214 160 58.4 31.4 81.2 45.0

12 EUF80-26 264 180 86.6 59.1 72.0 75.0

13 EUF100-20 214 240 54.2 48.1 73.6 55.0

14 EUF100-26 264 297 84.6 93.2 73.3 110.0

15 EUFS 80-315 324 128.4 128 65 70 75.0

16 EUFS 80-400 400 157.2 170 120 61.7 132.0

17 EUFS 80-450 450 192.0 234 207 59 250.0

18 EUFS 100-315 324 238.8 130 114 74.5 132.0

19 EUFS 100-400 400 270.0 198 198 75.4 220.0

20 EUFS 150-315 324 429.6 129 186 80.5 220.0

21 EUFS 150-400 400 507.0 198 356 77.3 400.0

22 EUFS 200-315 324 672.0 124 268 85.2 315.0

EUF/EUFS Performance - 50Hz

w h e r e i n n o va t i o n f l o w s

TM

EUF/EUFS series

EUF Installing Dimensions

FRONT ELEVATION SIDE ELEVATION

Pump Model

Bear

ing

Hou

sing

Dis

char

ge

DN

2

Suct

ion

D

N1

Pump Dimension (mm)

Foot Dimension (mm) Shaft End

Net

Wei

ght

a f h1 h2 b c n3 m1 m2 n1 n2 s w d l t u

EUF50/13

2550 65

100 360

132 160

50

14

100

100 70

240 190

14

267 24 50 27 8

35

EUF50/16 160 180

110

265 21239

EUF50/20 160 200 49

EUF50/26 180 225

65 125 95

320 250 66

EUF50/32 35 125 470 225 280 345 280 342 32 80 35 10 102

EUF65/16 25

65 80100

360160 200 280 212

267 24 50 27 845

EUF65/20 180 225 320 250 71

EUF65/26 35 470

200 25080

15160 120

360 28018 342 32 80 35 10

84

EUF65/32

125

225 280 18 400 315 111

EUF80/16 25

80 100

360 180 22565

14125 95

320 25014

267 24 50 27 8 56

EUF80/20

35 470

180 25015

345 280

342 32 80 35 10

73

EUF80/26 200

280 80 160 120

400 315

18

93

EUF100/20 100 125 16

360 280 86

EUF100/26 140 225 400 315 116

h2

h1

n1

n2 m2m1

n3

c

b øs1

ø14

l

faDN2

DN

1

6

u

d

w

t

DN

2

h3

d

DN1

f

ws2

m2

m1

l ye

w h e r e i n n o va t i o n f l o w s

TM

EUF/EUFS series

Euroflo Pumps International Pte Ltd No.1 Joo Koon Way Singapore 628942 Tel: +65 6861 3836 Fax: +65 6861 3936

Pump Model

Bear

ing

Hou

sing

Dis

char

geD

N1

Suct

ion

DN

2

Pump Dimensions (mm)

Foot Dimension (mm) Shaft End

Net

Wei

ght

e f h2 h3 h1 m1 m2 n1 n2 b s1 s2 w y d l t u

EUFS80-315 2

80 100

185 560 300 160 225160 120

400 31580 18

14 490

180

32 55 35 10 165

EUFS80-400 3 180 625 350200

280 435 35518

530 4280

45 12 249

+EUFS80-450 4 200 675 400 330 200 150 550 450 100 23 575 48 51.5 14 267

EUFS100-315 *2

100

150

195560

320160

250 160 120 400 315 80 1814 490 32 55 35 10 183

EUFS100-315 3

625

200 18

530 42

80

45 12203

EUFS100-400 *3210 380

280

200 150

500 400

100 23

275

EUFS100-400 4 575 48 51.5 14 305

EUFS150-315 3

150

205 370530 42 45 12

226

+EUFS150-400 *3230 410 315 550 450

250

295

+EUFS150-400 4 675 575 48 51.5 14 326

EUFS200-315 *3200 200 245

625420 300 500 400

530 42 45 12 271

EUFS200-315 4 675 575 48 51.5 14 297

EUFS Installing Dimensions

SIDE ELEVATION

* For low speed 1450rpm+ Suggest use centerline type for pressure above 22bar at shut off head

FRONT ELEVATION

d

u

t

EUF-

EUFS

/ A

PR 1

3

n1

h1h2

s1 bn2