Upload
others
View
0
Download
0
Embed Size (px)
Citation preview
LUND UNIVERSITY
PO Box 117221 00 Lund+46 46-222 00 00
Fire Hazards and the Compartment Fire Growth Process : Outline of a Swedish JointResearch Program
Pettersson, Ove
1980
Link to publication
Citation for published version (APA):Pettersson, O. (1980). Fire Hazards and the Compartment Fire Growth Process : Outline of a Swedish JointResearch Program. (Report / Lund Institute of Technology, Lund, Sweden, Department of Structural Mechanics;Vol. R80-5). Lund Institute of Technology.
Total number of authors:1
General rightsUnless other specific re-use rights are stated the following general rights apply:Copyright and moral rights for the publications made accessible in the public portal are retained by the authorsand/or other copyright owners and it is a condition of accessing publications that users recognise and abide by thelegal requirements associated with these rights. • Users may download and print one copy of any publication from the public portal for the purpose of private studyor research. • You may not further distribute the material or use it for any profit-making activity or commercial gain • You may freely distribute the URL identifying the publication in the public portal
Read more about Creative commons licenses: https://creativecommons.org/licenses/Take down policyIf you believe that this document breaches copyright please contact us providing details, and we will removeaccess to the work immediately and investigate your claim.
LUND INSTITUTE OF TECHNOLOGY . LUND· SWEDENDEPARTMENT OF STRUCTURAL MECHANICSREPORT NO. R80-5
OVE PETTERSSON
FIRE HAZARDS AND THE COMPARTMENTFIRE GROWTH PROCESS-OUTLlNE OF ASWEDISH JOINT RESEARCH PROGRAM
LUND INSTITUTE OF TECHNOLOGY. LUND. SWEDEN
DEPARTMENT OF STRUCTURAL MECHANICS
REPORT NO. R80-5
OVE PETTERSSON
FIRE HAZARDS AND THE COMPARTMENT FIRE GROWTH PROCESS
OUTLINE OF A SWEDISH JOINT RESEARCH PROGRAM
Reprinted from FoU-brand (Fire Research and DevelopmentNews) No. l, 1980
l e 1980ranForskning och utveckling·brand • Fire Research and Development NewsUtges av Svenska Brandförsvarsföreningen med ekonomiskt stöd av Styrelsen för svensk brandforskning. Publisherl by The Swedish. Fire Pro;ection. Asso~iation withfinancial support by The Swedish Fire Research Board Kungsholms Hamnplan 3, $-11220, Stockhol.m.• Sw~den. Tfn. 08/5208. 40. U~glvareJPubhsher:. managmg dlreclorKjell Gunnarson. Redaktör/Editor: tekn lic Vilhelm Sjöiin, Styrelsen för svensk brandforskmng. AdmInistrativ re.daktorlManagmg ed!tor: 9un,,:,or Beije, SB.F/SFPA. RedaktionsrAd/Editorial board: profe_ssor.Kai Qdeen, Kungl Teknis]<:a ..Hö.8skolan, Stockholm,. docent Harald Frosthng, Svenska Arbetsglvareforemngen, avdelningschef ArneWestlin, Arbetarskyddsstyrelsen, overlngenjor Lars Bergman, ForsakrIngsbranschens Service AB. Best nr 1243
Fire hazams and the compart..ment fire growth process... outline of aSwedish ioint research programBy Ove Pettersson1
1. NATIONAL SWEDISHFIRE RESEARCHPROGRAM
As has been reported in previous issuesof this journal, an expanded fire research program has been initiated inSweden [1] as a joint venture betweengovernment, insurance companies andprivate industry. Based on an extensivesurvey carried out whitin the NationalDefense Research Institute (FOA) [2],the present three year program (endingDecember 1981) is defined by 26 specified research projects. These are nowin various stages of implementationunder the supervision of the established board of directors and a programsecretariat - the Swedish Fire Research Board. The overall programcovers most of the major research areas: fire growth processes and spread ofsmoke and fires in buildings (sectorB), their impact on human behaviour(sector H) and on materials and products (sector M), fire fighting and firedetection and extinction (sector K),systems and operational research (sector S), and general and overall functions and surveys (sector F).
Admittedly, there is a considerablevariation in depth and scope. Naturallimitations in resources. and nationalcompetence necessarily led to projectspecifications in some cases merelyasking for further survey and feasibility studies. One major sector where an
l Division of Structural Mechanics, Lund Instituteof Technology, Lund, Sweden
active and extensive contribution already has started concerns the area ofbuilding fire growth and spread in thepre-flashover stage. The aim of thepresentation given here is to outlinethe scope, contents and organizationof this particular effort and, in a fewcases, indicate some of the experiencesand results obtained so far.
2. SCOPEANDORGANIZATION OF AJOINT PRE-FLASHOVERCOMPARTMENT FIRERESEARCH PROJECT
Among the 26 research projects, constituting the national program, thefollowing four were thought to be interrelated to such a degree that greatadvantage could be gained by a combined study, made simultaneously andin paraIleI.
The titles of these are• project B2: generation of smoke and
toxic gases,• project M3: surface lining materials
- c1assificationand fire hazards,• project M4: building materials - fi
re tests and fire growth,• project M6: upholstered furniture
- fire safety requirements.The combined project has the title
"Fire Hazard - Fire Growth in Compartments in the Early Stage of Development (Pre-flashover)" and is carried out as a joint project by the Division of Fire Technology and the Labo-
ratory for Chemical Analysis at theSwedish National Testing Institute,Borås and the Division of StructuralMechanics at Lund Institute of Technology.
The ultimate goal of the project isto develop test methods in full orhalf-sized 'scale for surface lining materials as weIl as for furniture andother fittings, from which the real behaviour and contribution of the testedmaterial or product in a natural firecan be predicted. To achieve this goal,it will be necessary to develop andexploit theoretical analyses, based onreliable mathematical models for allthe fire processes, those making use ofinformation obtained from the testmethods and those processes describing the fire itself, e.g. the flows ofgases and the energy transfers. Suchanalyses will also facilitate the formulation of functionally based requirements and performance criteria. Animportant, paraIleI task within thecombined project is to evaluate thosesmall scale "reaction to fire" tests,being developed within ISO/TC921WG2 and 4, and to relate them to what
ContentllnnehållFire hazards and the compartmentfire growth process .
Systematiska brandplatsundersökningar . . . . . . . . . . . . . . .. 10
The department of fire safetyengineering at the Universityof Edinburgh. . . . . . . . . . . . . . . . .. 17
Fire behaviour of Roaf Structures forIndustrial Buildings 20
FoU-brand 1/1980
2
REDAKTÖRENUnder de senaste 20 åren har forskningen kring bränders förlopp ochegenskaper i stort sett varit knutnatill brandförloppet efter övertändning. Det är i det skedet som byggnadens bärande delar påverkas medrisk för brott och sammanstörtning.Forskningsinsatserna har varitframgångsrika. Undan för undanhar kunskapen ökat och burit fruktbl a i form av kvalificerade, ingenjörsmässiga beräkningsmetoder.Ett stort steg framåt var byggnadslagstiftningens godkännande avteoretisk beräkning som ett alternativ till provning.
Emellertid formas brandensverkningar i stor utsträckning avbrandförloppets tidigare del. Detgäller särskilt verkan på människoroch på ömtåligare delar av byggnadskonstruktioner och inredning.Den tidiga delen av brandförloppetär dock ur forskningssynpunktmycket svår att hantera och förhållandevis få mera omfattande ochdjupgående projekt har kommit tillstånd. Ett skäl härtill är att manmåste räkna med en stor satsning pålångsiktig kompetensutveckling innan man kan förvänta resultat förpraktisk tillämpning. Med den finansiering som brandforskningentidigare haft i vårt land, har det varit svårt att garantera så stora anslag under tillräckligt lång tid föratt göra satsningen meningsfylld.
Förhållandena har emellertidförändrats sedan BRANDFORSKtillkommit. En av dess första åtgärder blev därför att bevilja medelför ett stort projektblock av ny karaktär. Härigenom har Institutionen för byggnadsstatik vid Lundstekniska högskola i samarbete medbrandlaboratoriet vid statens provningsanstalt kunnat påbörja ett treårigt projekt - "det tidiga brandförloppet" . De båda forskningsinstitutionerna har genom att skjutatill egna medel kunnat disponera ca4 miljoner kronor t o m 1982. Projektet stöttas ytterligare av formaliserat samarbete med Fire ResearchStation i Storbritannien och genominformellt samarbete med andra utländska institutioner och organ.
Professor Ove Pettersson redogör i artikeln för projektblocketssyfte och innehåll. Artikeln publiceras på engelska som ett led i ansträngningarna att tidigt orienteraomvärlden om vad som pågår inomden svenska brandforskningen. Envidare orientering för det svenskabrandförsvarets personal förberedsi annan form.
happens at real fires. Undertakingsuch a project, will have a significantrole in increasing the national fire research competence.
Tackling such an extensive andcomplex research area, an effective cooperation between research graups becomes a necessity. On the national level, an agreement to co-ordinate andco-operate in work within fire researchwas signed in 1978 between the Swedish National Testing Institute (SP)and the Fire Research Group at LundInstitute of Technology (LTH). As aconsequence, the application for theresearch grant sent to the Swedish FireResearch Board was a joint one and directly based on a factual and contifillOUS cooperation.
Internationally, documents outlining joint research interests betweenthe Fire Research Station (FRS), UKand LTH has been agreed. This collaboration will be focused on problemsin the growth of fire in compartmentsin the early stage of development (preflashover). Extensive discussions andconsultations have taken place withFRS and form much of the background for the formulation of the research project, presented in this article. Chapter 3 is largely based on theoriginal letter of intent for theFRS/LTH co-operation.
Il should also be mentioned the roleplayed for the project by the information dissemanating from the NationalBureau of Standards (NBS) inWashington. A number of people havewillingly discussed projects in progress, given access to unpublished data, to computer programs and in otherways facilitated our work. Furthermore, the activities going on within theAd Hoc Fire Mathematical ModelingCommittee in USA and within ClBWI4 - pIanning to. organize a workshop on pre-flashover fire mathematicaj modelling during 1981 - will considerably support the research project.
3. GENERALBACKGROUND OF THERESEARCH PROJECT
Traditionally, efforts to increase thefire safety in buildings have been directed towards requirements on structural components and - to alesser extent - also to building materials. Furnishings and other non-structural features of buildings have until recent time remained essentially non-regulated. Il is now widely recognized thatan increase in human firesafety levelsrequires an assessment of the roIe offurnishings and other building contents. Consumer demands in a numberof countries have resulted in efforts tocontroi the flammability of furnishingby statutary or non-statutary require-
ments. The material or product selection is almost invariably related toperformance in a specified small scaletest method. As of now, the relationship between the behaviour of materials in a test and in a real fire, afterthe initial ignition, remains unknownin any general predictive sense. Awealth of data is gradually becomingavailable regarding ignition times, flame spread velocities, burning intensities, radiation output and so forth, butthere is no satisfactory comprehensivetheory of furnishing fire behaviour onwhich to base design or predict hazard.To a large degree, this also applies tothe roIe of internai linings in the residential fire process. The problem isaggravated by the new materials andproducts being continually developed,expanding the range of fire responsesand performance charactetistics.
Fire science and technology are attacking the mountain fire problem bya number of avenues. In the area of internal linings, standard laboratory fire test methods are being designedwhich measure the quantitative response of a material to specified fireexposure situations. Examples are the"reaction to fire" tests being developed within ISO/TC92/WG2 and 4. Byoperating at a number of exposure levels, these tests will provide a comprehensive, quantitative description of basic fire performance characteristics (ignitability, surface flame spread, rateof heat release). Simultaneously, initial but nevertheless extensive effortsare being made to mathematically model fire process dynamics, in a numberof areas, to determine the dominantcontrolling mechanisms. Examples ofimportant subrnodels or aspects of thefire growth phenomena are• field and zone models for part tur
bulent flows in enclosures,• fire growth models (flame spread
under arbitrary externai radiation),• characteristics of flame and hot gas
radiation,• convective heat transfer through
ventilation openings,• convective heat transfer within en
closure.The modelling problems inherent in
the list of transient, thermophysicalprocesses enumerated above will notbe solved in detail for many years tocome. One of the major problems willbe to strike a proper balance betweenthe need for reasonably quick answersand the need for modelling accuracy.Tools to complement the analyticalmodelling comprise experiments infull or small scale, reliability studiesand empirical data from standardtests. Attempts at interpreting standard tests by modelling them alsohelps to extract data from (hem in themost useful way for wider application.
FoU-brand 111980
Table l. Scheme of integration for the eleven research items of the total pre-flashover research project
Research item Project
B2 M3 M4 M6
1. Analysis of SIS 02 4823 (Swedish box test) x x x2. Bum room sensitivity study x x x3. Fire behaviour of surface Iining materials - full
scale testing x x x4. Fire behaviour of upholstered furniture - full
scale testing x x5. Interaction between buming items of furniture
and combustible surface lining materials - fullscale testing x x x x
6. Pilot studies of fire induced compartment flows x x x x7. Mathematical fire modelling x x x x8. Development of methods for analyzing
combustion products of polymeric materials x x x x9. ISO reaction to fire tests - correlation to real
fire, dassification x x x10. Development of standardized full scale tests
(a) Surface Iining materials x x x(b) Furniture x x
11. Testing of upholstered fumiture using half-scalerigs x x
3
EDITORIAlSo far, most of the research on fireshas been dealing with the fire situation after flashover. This is notsurprising, as the fire effects on theloadbearing structural elements ofthe building, will be imposed during this stage of a fire. In lateryears, however, extensive researchon postflashaver problems hasopened the way for an analyticalstructural fire engineering design,based upon well-defined functionalperformance criteria.
However, there are good reasonsto pay more attention to the earlystage of fire. A threat to humanswill certainly become eminent already before flashover. Furthermore, in many cases, the early development of a fire will determine thefire loss regardless of later damageto the loadbearing structural elements. With this background, it isnot difficult to see the reasans forthe present worldwide trend in fireresearch to put more emphasis onthe early stages.
The Swedish Fire Research Boardis a new initiating and sponsoringbody in the field of fire research. Itis founded and funded by the Swedish Government and by privateenterprises on a 50-50 basis.Oneof its first undertakings was toestablish a block of projects aimedat studies of the early stage of fire.
In this artide, professor Ove Pettersson of the Lund Institute ofTechnology tells about the intentions and scope of the work. Theprojects are conducted in ca-operation between the Institute and theFire Technology Laboratory of theNational Testing Institute. Bypooling financial resources, closeto U.S. $ one million has been setaside for a period of three years.The work indudes considerable international collaboration.
A short term goal may be a predictive model of whether or not flashaverwill occur for a given set of initial conditions, and, if so, how long after igni~
tian it will occur.Our increasing capability in con
structing physical or mathematicalmodels for important fire scenariosimplies that rationai approaches to estimate life safety levels will graduallybecome avallable. The life safetyproblem must be approached by methodologies now being used within anumber of other sectors for assessingefficiency, sensitivity to disturbanceand reliability in complicated systems.Examples of analytical tools are probability theory, variance analysis,
FoU-brand 1/1980
mathematical programming (linear l
dynamic), decision analysis, systemssimulation. Most of these methods have been used previously in one form oranother in the field of fire research.The choice of method has usually depended on the design level, 1.e. on thesize and complexity of the system involved.
4. DETAll STRUCTURE OFTHE RESEARCHPROJECT
For a more detailed planning of thetotal research project, it turned out tobe useful to break down the project inta eleven smaller research items. Table lenumerates these items and illustrates their relevance for and connection to the four original research projects B2, M3, M4 and M6 in the national Swedish fire research program.The different research items are not directly comparable in regard to extentand complexity. One research item analysis of the Swedish box test - israther lirnited. Same other items belong to very fundamental researchareas with a high degree of complexity, for instance, items 6 and 7. For these items, the level of ambition for ajoint Swedish contributian naturallymust be limited to give only a few modest complements to the comprehensive international research development. Accordingly, Table 1 must bemadeconcrete in order to give maredetailed information on the scope andlevel of complexity of the different research items.
The remainder of the paper will beused to present the eleven research
items as weIl as the progress made upto now (August 1980). As will be noted, none of them is anywhere nearcampietian, most are still in an initialplanning stage.
4.1 Research Item 1.Analysis of SIS 02 4823(the Swedish Box Test!
The standard instrument in Sweden fora fire c1assification of building liningmaterials is the so called box test. Thetest configuration has features similarto the British fire propagation test andthe Dutch flashover test, the majordifference being that the ventilation iscontrolled in the Swedish box test.The material to be tested is attached tothe ceiling and three walls of a smallenc10sure and exposed to a ratherstrong gas flame without any additional impressed radiation. Materials aregraded by the time curve o f the fluegas temperature with three specified limit curves.
1t is known that material fire properties, for instance, mass buming rateper unit surface area, varies widely,and in many cases non-linearly, withthe level of thermal exposure. The vaIue of the test as a measure of the contributian of lining materials to the firegrowth and spread could thus be considerably enhanced, if the exposure levels during the testing process are measured and compared with those generated in common natural compartmentfire scenarios. Useful information willa1so be gained byarnare completeeriergy balance study of the test process, giving the rates of heat outputand heat transfer within the enc1osure.The practicality of using oxygen con-
sumption calorimetry to measure thequantity of energy release by combustion will also be studied.
The investigation will be carried outat SP during autumn and winter 1980.
KEI(;KT (m1
"
IolASS FLOW
(kg!5)
KEI(;KT (m)
"
tiO T;me(mj~_!
&O Time(min}
..
..
"
..
OIFFEREHCE
,.o+---~--~--~--~-_o
precise: Given a fire source withknown heat output near a wall,what will different classes of walland ceiling surface materials meanin terms of time to untenable situations inside the room, time to flash·over, etc?The Swedish full scale method for
surface finishes now in use was initially modelled on the room-corridor firespread situation. Being developed inthe late 1950's, the test method inevitably has some inherent drawbackswhen measured against modern standards and requirements. The test process may be sensitive to changes inweather conditions. Acceptance criteria are not firmly quantified but of arather subjective nature. The test process has not been correlated to oneroom fire growth scenarios.
As an alternative test procedure, thecorner test was an obvious candidate j
and the burn room at SP is being usedfor development work on a room corner test. To find suitable fire scenarios, a series of tests were ron with various surface finishes. Heptane burners of various sizes were used and several sizes of the opening of the compartment were tried. The burners wereopen containers with water and heptane floating on top. Materials to be tested were mounted on walls and ceiting.
000
Figure 3. Measured rate of heat loss byconvection Qa versus time. StationarYconditions. Test I: Qe = 125 kW. TestII:Qe = 250kW[3]
'"
EFFECT
(kW)
"
'"".
lHFLOW
,.o~
Figure 2. Measured mass flow in andout of fire compartment and the difference of these values versus time.Qe = 250kW[3]
1.0 2.0
~:/~F~~r
o.,
-2.0 -1.0
(a) 0c = 125 kW
o, j-Z.O -1.0 o-~,-o~Z'_O
~ASS FLOW(k,,/5 m Z)
bl Qe" 250 kW'.0
(b) Oc = 250 kl.
Figure 1. Mass flow profiles in thedoorway at two rates of heat releaselevels [3]
4.3 Research Item 3.Fire Behaviour of SurfaceUning Materials - FullScale Testing
Recently, the Swedish regulations regarding the use of surface finishingmaterials were substantially extendedto cover new classes of buildings (essentiaIly, one family homes) and interior surface areas, which previouslyhad not been regulated. The minimumrequirements for all surface finishingmaterials, sold to the consumer, arethat their flammability characteristicsmust give at least equal safety as thoseof massive wood, when tested in theSwedish hot box.
The extension of governmental regulations brings a renewed urgency tosome old and only partial1y solvedproblems regarding a functional classification of surface finIshes. Amongthese are
• to what extent is the classification ofa surface material dependent on thechoice of base or backing material(degree of combustibility, value ofthermal inertia)?
• what is the relation between theclassification of a Iining material inthe box test and the contribution ofthe same material to room firegrowth and spread? Or to be more
4.2 Research Item 2.Burn Room SensitivityStudy
A full scale experimental burn roomhas been built and instrumented at SP.It will serve several functions duringthe project, viz.,
• to establish basic f1ame spread andcombustion characteristics of liningmaterials as well as furnishings (upholstered furniture) under full scaleconditions,
• to serve as basic configuration for aroom corner test,
• to serve as a room size calorimeter.
The instrumentation basically follows the "Recommended Practice forRoom Fire Test", issued by ASTME-39.101, the main difference beingthe number of bi-directional probesfound necessary to map door f10wconditions.
An extensive energy and mass balance calibration with gas burner asfuel source has been carried out andsummarily reported in [3]. Energy, re·leased by combustion in the fire room,leaves the room by convection and radiation through the doorway and byconduction through the surroundingstructures. The object of the calibration tests was to evaluate the variouscomponents at heat transfer and estimate the accuracy of the measurements by checking the heat balance.
In a first series of calibration experiments, gas velocity or rate of massf10w and temperatures were measuredonly a10ng a vertical line in the centerof the doorway. Considerable differences between calculated total rate ofmass f10ws in and out of the fire roomwere, however, registered because thehorizontal distributions of gas velocityare different in the f10ws in and out.
A second series of experiments wastherefore made where the horizontaldistribution was investigated. Themass flow and the temperature werethus measured in 66 points over thedoorway.
Examples of the vertical mass flowprofiles are shown in Fig.1 - the massf10w is integrated horizontaliy overthe doorway. Fig. 2 shows an exampleof the measured mass flow in and out,integrated over the doorway, and thedifference between these two as a function of time. The total rate of energyf10w Qa out of the compartment, integrated over the doorway, is given inFig. 3. As shown by Fig. 2 and 3, theaccuracy of the measurernents is satisfactory.
4
<2 min.
2 min,6 min,
20 min,
• to estimate the time available for escape or evacuation out of the roomof fire origin, Le. the minimum timefor a hazard component (heat, smoke or toxic gas concentration, heatfluxes) to reach untenable conditians,
• to validate the results obtained bysimulation computer programs. Inour case the Harvard Computer FireCode [5J and a time-dependent version of the Quintiere model, developed at FOA, Stockholm [6J wereused,
II to find correlation with experimentscarried out with a prototype scaleddown test rig (see further researchitem 11).
As an example of the results derivedin [4], Fig. 4 gives for five differentmaterial combinations the total, accumulated smoke production Dacc as afunction of time. Dacc is expressed, inaccordance with the terminology usedin [7J, as (dB/m) . m', where the firstfactor expresses light attenuation asdecibel per m of light path through theoutflowing smoke, and the second oneexpresses the total flow of combustionproducts (smoke). Table 2 gives details of the material combinationsused. Fig. 4 clearly illustrates the in-
®
t 000
2000
:::: jr
5000
4000 ~l
3000 J
Development, has been carried out inthe previously mentioned burn roomat SP and been preliminary reported[4J.
To get reproducible fire scenariosand clearly defined and measurablereactions to variations in the main parameter, Le. material selection, thetest furniture was a full scale mock upmodel of a three-seat sofa, designedwith loose cushions on a steel frame.A liquid fuel burner with a heat output of 20-30 kW was used as ignitionsource.
The materials of the cushions waschanged in a systematic way to represent the ranges available in the consumer market. In all, Il sofas were tested. Extensive measurements were taken of mass burning rates, gas temperatures, gas flow velocities, heatfluxes to floor and ceiling, smoke concentration and gas species concentratians.
The experimental data have beenprocessed and analyzed for a numberof purposes, viz.
• to assess basic components of therisk profile of the product (rate offire spread, maximum rate of heatrelease, concentration of producedsmoke),
A square burner with a surface of0.03 m' gives approximately a rate ofheat release of 50 kW, thus simulatinga burning waste paper basket. Whenthe burner was placed in a corner, thefollowing time intervals between ignition of the burner and flashover (defined here by flames coming out of theopening) were recorded
" untreated porous board• chip boardIl surface veneer, bonded to
chipboard• polystyrene foam, flame
retardant
With the same test conditions, thefollowing products did not causeflashover
• plaster board,• PVC-wallcovering, on plaster
board,• traditional wall-paper, on non
combustible board.
The PVC wall paper was also testedwith smaller openings and with a larger burner; on no occasion did flashover occur.
To complement the full scale studies, a series of room corner tests in model scale has been planned. Some preliminary tests have been performed ina cubic room with dimensions I x l x lm' for a study of ignition, fire growthand flashover at different combinations of wall and ceiling linings, madeof wood or wooden-based products. Agas burner. placed in a corner. wasused for simulating a scaled-down,representative thermal exposure. Temperature, gas velocity, heat flow andheat radiation were measured. In thefollowing tests, the measurement system will be expanded with an oxygenconsumption calorirneter for a determination of the energy, released bycombustion. An evaluation of the results of the preliminary tests is inprogress.
Table 2. Material combinations nsed in full scale tests of upholstered furniture
Figure 4. Total, accumulated smoke productian Dacc as function of time fortests 5, 6, 7, 8 and 11 [4]4.4 Research Item 4.
Fire Behaviour ofUpholstered Furniture Fuil Scale Testing
The overall objective of project M6 isto study the fire behaviour of upholstered furniture to assess the hazards,associated with ignition, growth of fireand production of smoke and toxic gases. A major element is developmentand validation work to produce functionally based fire tests ..Research item4 in particular comprises a study of thefull scale burning characteristics ofupholstered furniture, as influencedby the choice of upholstery Jabric, interlining and filling material. A firststudy, financed by the industry and theNational Swedish Board for Technical
Test No.
l23
45678
91011
Upholstery fabric
Acrylic 1000/0Acrylic 100%Acrylic 100%
Woolloo%Acrylic 100%Wool61 "lo, viscose 39%Wool61 "lo, viscose 39%Wool61 "lo, viscose 39%
Wool61 "lo, viscose 39%Wool61 "lo, viscose 39%Woo161 "lo, viscose 39%
Interliner
FirendVonarKynol
FiIling material
ConventionaI polyurethaneConventional polyurethaneConventionaI polyurethanewith FR additivesConventional polyurethaneConventionai polyurethaneConventionai polyurethaneHigh-resilient polyurethaneConventionai polyurethanewith FR-additivesConventionai polyurethaneConventionai polyurethaneConventionai polyurethane
FoU-brand 1/1980 5
Figure 5. Smoke producing potentialper unit weight of eonsumed fueJ Do asfunetion of time for tests 6, 7and 8 {4}
fluenee of material selection on the rate of smoke production.
An effort was also made to examinehow the quantity Do, (dB/m) . (m' /g),expressing the smoke producing potential per unit weight of consumed fuel,varied over the fire process. A constantvalue of Do obviously would providea convenient way of classifying materials. Unfortunately, as shown by Fig.S, Do varies strongly and shifts ranking order during the fire process.
4.5 Research Item 5.Interaction betweenSurning Items ofFurniture andCombustible Surfacetining Materials ~ FullScale Testing
This item should be studied at the endof the three-year program, when results from items 3 and 4 are availableand have been analyzed.
4.6 Research Item 6.Pilot Studies of FireInduced CompartmentFlows
Througout the series of full scaletests, which will be carried out forother, primary objectives, velocitymeasurements will be taken of the gasflow field inside the fire compartment(upper gas layer) as well as in the ventilation opening. The instrumentationwiU be based on the use of bi-directional probes, and one purpose will be totest the accuracy and speed, espedallyin highly transient compartment fires,of the measurement system. Other purposes include the need to check the limits and definition of the controi volume concept now used in the zane
6
modelling approach. In particular twoidealisations need further examination. The first is the concept that thefluid in the fire room is stratified intotwo horizontal layers of uniform temperatures with no mixing. The investigations in [8J imply that secondary andrecirculatory flows near the enclosureopening may be an important cause ofreducing the oxygen concentration ofthe combustion air and hence the massburning rate. The second concept is theone of a ventilation outflow, driven bya hydrostatic pressure distribution andwithout influence from the kineticenergy of the rising fire plume gasflow. These two approximations concern the basic problem of predictingthe temperature rise in the upper partof the enclosure and the concentrations of combustion products and unburnt fuel, and the way the fire interacts with the enclosure. In addition,measurement~ taken under researchitem 2 are being used to compute an effective flow coefficient. It is importantto investigate how the flow coefficients vary with the range of size of ventilation openings and fire sourcestrengths, encountered under practicalconditions.
4.7 Research Item 7.Mathematical FireModelling
The developments, taking place in thelast five years within the area of computerbased simulation of the enclosure fire process, has led to a number ofmedels for common fire scenarios.The range of practical application aswell as the predictive capability of these models is steadily increasing. Themore recent developments were sketchily summarized in a review report tothe 1980 CIB WI4-meeting in Athens[9].
In [9], available models were, some·what arbitrarily, divided into generalpurpose enclosure fire models (theQuintiere model and its successor [6]),models of growth of compartment fires involving combustible lining materials, models for a specified application - such as early growth of the closed room fire or the ventilation required to perrnit sustained burning orgrowth of compartment fire - and, fi·nally, models for a simplified prediction of room flashover. Other important modelling areas include probabilistic models for fire spread, modelling of laboratory scale tests, modelling of essentially micro'scale firephysics (ignition, flame spread, extinction), see e.g. the very recent survey in[17].
The research group expects to participate actively in the efforts takingplace within the cm framework to vitalize and co-operate with the European work on fire modelling.
The specifications for project M4emphasizes the need for establishing anational competence in this sector offire research. Within the project, theefforts will be concentrated on twotasks.
With the kind assistance of NBS andthe Harvard Fire Research Group, version four of the Harvard computer firecode [5J has been transferred to LTH,and is now being used to simulate thefull scale tests, mentioned under item4. Simultaneously, the predictive capacity of the FOA simulation programFLASHOVER [6J for this kind ofcompartment fires is being looked into.
The second task concerns a modelfor the prediction of wall fire spread.Very recently, important elements ofan analytical model describing the fla·me spread process across a combustible wall were for the first time outlinedby Quintiere [JO]. An effort will bemade to couple the experimental dataproduced in the model and full scaletests under research item 3 with theongoing efforts to put the mathematical modelon a firmer base.
4.8 Research Item Il.Characterization ofCombllstion Productsfrom Small and Full Scalelaboratory Fires
The overall responsibility for this partof the total project will be with theLaboratory for Chemical Analysis atSP. The primary aim of the researchtask is the development and calibration of a measurement system, basedon gas chromatography and massspectrometry, to analyze the combus·tion products from laboratory fires.These can be generated in small scalestandard tests such as the Swedish boxtest or the Smith RHR apparatus asweil as by full scale experiments usingthe burn room. In the first year, thesystem will be assembled and calibrated, while the second and third year.will be used to qualitatively and quantitatively identify possible toxic species from a number of natural andsynthetic polyrneric materials, withand without fire retardant additives.
4.9 Research Item 9.ISO Reaction to FireTests ~ Correlation toReal Fires. Classif/cat/on
The procedures available for predic·ting fire hazard from small scale testsare outlined in the ISO Technical Re-
FoU-brand 111980
with
V-I/2 = C(q' ". - q' ")f O,lg e
V·1!2 - CI (T T)f - 19- s
Tig effective ignition temperature,and
Ts surface equilibrium temperatu~
re.
The development of standardizedfull scale tests for furnishings, e.g. upholstered furnitures and beds, for thepost-ignition phase, is in a still moretentative stage of development.
A number of factors determine thehazard profile of a specified product,involved in the post-ignition stages ofa room fire: flame spread and firegrowth properties in general, maximum rate of combustion heat release,generation of smoke and toxic gases.The components in the first and thirdcategory determine the time availablefor safe escape, while the maximumrate of heat release indicates the risk ofroom flashover and spread to otherrooms. The flashover phenomena have been the subject of a number of recent papers and certain quantified limit criteria have been proposed. Theother hazard components, acceptancecriteria cannot yet be determinedobjectively.
The most extensive work has probably been carried out in the UK and,by way of an example, resulted in a series of "fire retardant specifications",issued by DOE/PSA [14]. One of these, DOE/PSA. FR 6, tests the burningcharacteristics of upholstered chairsby a burn-out test in an instrumentedroom. Data collected during the testinclude smoke temperature, opticaldensity and volume, heat fluxes to theenvironment and CO-concentration.
To test, for instance a full scale pie·ce of an upholstered furniture in a fully instrumented burn room, using ca~
lorimetric measurements and energybalance equations, involves a considerable amount of time and east. AIso, as long as effective ventilationflow coefficients are not available as afunction of opening geometry and heatsource strength, the number of velocity probes necessary for accuratelymapping highly transient gas flow velocity fields makes for a rather unwieldy test procedure. An attractivealternative in this situation is tOtiseoxygen consumption techniques [13 J.Still another approach is the room sizedynamie room calorimeter, developedat Monsanta [15], working under forced air flow conditions. The impact onburning characteristics of the artificialflow system may not be negligible,however. As a further alternative andif the influence of the enclosure on thefire growht process is of minor importance, pieces of furniture could be tested by free burning under an exhausthood and with rate of heat releasemeasured by oxygen consumption.
The problem of enhancement ofburning rate by thermal feed back,from enclosing structures and uppergas layer, was investigated by Thomas[16], who found that the ratio of rateof burning at the flashover point for a
is a material parameter, including radiation from flame, effective width of this radiation,thermo-physical properties,is minimum radiation flux forpiloted ignition, andis the imposed radiation flux.
q~,ig
where
c
q;
4.10 Research Item 10.Standardized Full ScaleTests
This research item is considered one ofthe more important part objectives ofthe total project. Experience has clearly demonstrated that small scale laboratory tests may give mislcading andeven erroneous information regardingmaterial or product performance in anatural fire. The need for further fullscale studies, using internationallystandardized procedures, where possible, is thus direct and urgent. Thisapplies to surface lining materials asweIl as furnishings.
For surface lining materials, initialdevelopment work has been describedunder research item 3. The work beingcarried out in the USA to produce anASTM room corner test is being clasely monitored [13J.
Quintiere also shows how values ofC and q".ig may be determined for aspecific material from a single test runwith the surface spread of flarne apparatus. Values of q".ig can also be obtained by imposing a uniform fluxover a smaller sample.
For a thermally thick material, there is a unique relation between q~ andthe corresponding equilibrium temperature. This implies that an alternativeexpression for Vf is
A key element in the Quintiere conceptual quasi-steady model for wallfire spread is a simplified theoreticalmodel of surface spread of flame under sup·porting radiation, such as canbe studied on the equipment being developed by ISO [12]. A simple expressian for the horizontal flame spread V,as may OCCUr in a corner test fire canbe theoretically derived if the materialis preheated so that its rear surface isstill cold when the front face hasreached thermal equilibriurn, viz.
port TR 6585 "Fire Hazard and Design and Use of Fire Tests". October1979 and in [16]. In the absence of analytical models for a standard testand/or the full scale experiment,multi-dimensional regression analysiscan be used to correlate test resultswith values of specified full scale experiment variables (maximum roomtemperature, time of flashover, etc).On the other hand, an analytical model of the small scale test dynamicscan provide information on a numberof important aspects. Identification ofthe test sample characteristics (area,orientation, exposure conditions),which contral the test outcome, formsthe basis for numerical simulationsand a sensitivity analysis of the testmethod itself. With a mathematicalmodel of the test dynamics to hand,important material characteristicscontrolling fire growth can be givenquantitative values, which then can beused as input for full scale. This procedure .would be of value, especiallyfor non-homogeneous materials, where relevant material properties, likethermal inertia, otherwise might notbe obtainable.
The research group participates activily in ongoing development and validatian work on the ISO reactian to firetests. The apparatus for ignitability,surface spread of flarne and smokegeneration is being evaluated at SP. AtLTH, calibration work is now beingdone on the rate of heat release (RHR)apparatus, designed by Prof. Smith atOhio State University. The apparatusis instrumented to measure the rate o fheat release by convective heat flowasweIl as by oxygen consumption.Among the problems likely to be encountered, if basic data are to be ob-
tained for wide use, is the fact that theapparatus, designed to work duringtests at constant levels of impressedradiation, progressively heats up andincreases the thermal exposure [Il].
Other RHR standard tests under development include an unconfined design configuration. To this group oftest methods belongs the NBS rate ofheat release test, based on measurement of the oxygen depletion. A grantfor a further study of this test has beengiven to the Swedish Forest ProductsResearch Laboratory.
Also the Swedish box test, cf. itemI, may be considered as a crude prototype to a RHR test method.
If a given material is being testedwith the three methods mentioned, thetest results will certainly differ. Anunderstanding of the differences in thetest processes will help to provide a rational explanation of the divergencesas weIl as of the relation between thetest methods and the natural fire process.
7
1500
oL..l"-"...L..l....lL.J:'--"''''--''--''-.L-'--..JL.L..J=-'--.b.L-'''--''..L..JL.L..J=_~
TESTNo 2 3 5 6 7 8 9 10 11 13 l' lS 16 11 18 19 2011 12 2' 2S 26
D ConvenlLonolpolyurelhone
1000
500
fire in an enc10sure to the rate of burning when the same product is allowedto burn freely in the open, is nearly aconstant '" 1.7. The implications arethat results from a free burning test,indeed can be used to indicate the riskfor the same product causing roomflashover.
Finally, as our own and others experiments have demonstrated, a test toassess the horizontal flame spreadproperties of furniture with extendedsurfaces remains essential both to provide basic input data in computer-based mathematical models of enclosurefire growth and as a more direct riskelassification tool. As pointed out in[16], fire spread may be more susceptible to radiative enhancement thanpure rate of burning.
r------------IIL~,
\\
\\\
\
Table 3. Total accumulated smoke production Dacc for upholstered fumiture,obtained in half-scale and full scale tests [4J
Figure 7. Total, accumulated smoke produetian Dacc for pieces of upholsteredfumiture, determined in ha/f-sca/e tests. In the tests, not reported in the figure,the smoke produetian was to small to enable any eva/uation [4]
39 40 'l 42 43 ,s 46 47 48 SO 51 S2
17T p-
17 17'/
/ 1/ // 1/ 1/ 1/ // V 7 1/
"XV /
r- / V / V 1/r; // " V / / '" V /~ r '" - '"V V V '/ V /
~
"-
" I- '" ~ "V"
V'" ~
/
" F:; V"
1/
"V"
'/
'" '/
" ~ /
"V ~
V"
'/"7" V j "X '"/
"V
'"1/ / 1/ / 1/oTEST No 21 28 29 31 32 33 3' 3S 36
500
1000
1500
r-------------IIIII
r~
J/
// .,
//
/
4.11 Research Item 11.Testing of UpholsteredFurniture UsingHalf-Scale Rigs
It follows from the discussions underresearch item 10 that obvious advantages would be gained, if testing of pieees of furniture could be made on specimens of a reduced size.
As a part of the project, brieflydescribed under research item 4, anumber of burning tests (52) were performed with a testing rig designed according to DD 58:1978, the originalproposal for a British ignitability standard. The test configuration is described by Fig. 6.
@ PHOTOCELL • THERMOCOUPLE
o GAS FLOW MEASUREMENT
Half-scale Full scale
Test No.
2530208039056910
465603639
1296
Smoke production Dacc ('!!f . m')
Half-scale Full scale
5678
1464847
LOAOING/CELL
Figure 6. Arrangements for testing upholstered fumiture, using a ha/f-sca/erig.
To illustrate the results obtained,Fig. 7 outlines the range in total accumulated smoke production Daee, obtained by material changes and modifications. Finally, Table 3 gives thecorrelation between full scale and model scale testing for those few caseswhere results are obtainable.
The table indicates a positive correlation but shows simultaneously thatthe relative ranking order is not unambiguous. Before more definite conelusions can be drawn, further tests mustbe carried out.
5. SUMMARYThe following four projects from thepresent National Swedish fire researchprogram
• generation of smoke and toxic gases(B2),
• surface lining materials - elassification and fire hazards (M3),
• building materials - fire tests andfire growth (M4),
• upholstered furniture - fire safetyrequirements (M6)
have been brought out and integratedto a research project with the tille "Fire Hazards - Fire Growth in Com-
8 FoU~braD~ 1/1980
partments in the Early Stage of Development (Pre-f1ashover)". The integrated project is carried out as a jointproject by the Division of Fire Technology and the Laboratory for ChemicalAnalysis at the Swedish National Testing Institute (SP), Borås and the Division of Structural Mechanics at LundInstitute of Technology (LTH). Within the frarnework of a collaborationagreed between the Fire Research Station, UK and LTH, extensive discussions and consultations have takenplace and are forming much of thebackground for the formulation of theresearch project. The project is financed by the Swedish Fire ResearchBoard.
The paper presents the generalbackground, scope, organization anddetailed structure of the integrated research project. In order to facilitatethe detalled planning, it turned out tobe useful to break down the project into eleven smaller research items.Table lenumerates these and illustrates their relevance for and connectionto the four original research projectsB2, M3, M4 and M6 in the nationalSwedish fire research program.The maln part of the paper is devotedto a presentation of the eleven researchitems as weil as the progress made upto now (August 1980). As it appears,none of them is anywhere near completion, most are still in an initialplanning stage.
The final goal of the project is defined as the development and validation of test meihods, for surface liningmaterials as weil as furnitureandother fittings, having the capability ofpredicting the behaviour and contribution of the tested material or productto natural fire growth and spread in acompartment. In order to achieve thisgoal, analytical modelling of thecompartment fire process becomes anecessity, e.g. as a tool to perform sensitivity studies; In this sense, the use ofmathematical models a1so facilitatesthe formulation of performance-basedclassification requirements. Specifically, evaluation and verification ofthe ISO reaction to fire tests representsan important task.
ACKNOWlEDGEMENTDr Philip Thomas,Fire Research
Station, UK, has generously contributed in consultations and discussions,giving a decisive influence on the formulation of the research project, presented in this article. He has a1so actively followed and given advice on individual research items of the project.
All participants in the research project wish to express their hearty thanksfor this support and look forward to astimulating future co-operation.
REFERENCES[I] FoU-brand (Fire Research and
DevelopmentNews),1·1979.[2] FoU-brand (Fire Research and
Development News), 2·1979.[3] Sundström, B. and Wickström,
U., Fire: Full Scale Tests Background and Test Arrangements, Technical Report SP Rapp 19S0:14, Borås 19S0.
[4] Andersson, B. and Magnusson,S.E., Fullskaleprov - Brand istoppmöbler (Full Scale Tests Fire Behaviour of UpholsteredFurniture), Byggnadsstatik, LTH,June 19S0.
[5] Mitler, H.E., The Physical Basisfor the Harvard Computer FireCode, Home Fire Project, TechnicaJ Report No. 34, actober 1975.
[6] Häggiund, B., Simulating theEarly Fire Orowth in ResidentialRooms, FOA, Stockholm 19S0.
[7] Rasbash, D.J. and Pratt, B.T.,Estimation of Smoke Produced inFires, Fire Safety Journal, Vol. 2,January 19S0.
[S] Quintiere, J.O., McCaffrey, B.and DenBraven, K., Experimentaland Theoretical Analysis ofQuasi-Steady Small ScaJe Enclosure Fires, NBSIR 7S-1511.
[9] Magnusson, S.E., Recent Developments in Mathematical Modeling of Fire Orowth, Notes for areport to the ClB/W14 meeting inAthens, May 1980.
[10] Quintiere, J., An Approach toModeling of Wall Fire Spread ina Room, Presentation given at theP .H. Thomas Honorary Conference, Washington, Apri119S0.
[II] Babrauskas, V., Private comrnunication.
[12J Quintiere, J., A Simplified Theory for Oeneralizing Results froma Radiant Panel Rate of FlarneSpread Apparatus. To be published.
[I3J Williarnson, R.B. and Fisher,F.L., Fire Orowth Experiments Toward a Standard Room FireTest WSS-79-48, Department ofCivil Engineering and LawrenceBerkeley Laboratory, Universityof California, Berkeley.
[I4J Paul, K.T., Fire Testing of Upholstered Furniture and Bedding,Fire and Materials, Vol. 4, No. 2,19S0.
[15] Fitzgerald, W.E., Kinetics of Burning in a Room Sized Calorime-
ter, Nat Symposium on Fire Safety Aspects of Polymeric Materials, American Chemical Society,1977.
[16J Thomas, P.H., Testing Productsand Materials for Their Contribution to Flashover in Rooms. To bepUblished.
[17] Thomas, P.H., Fire Modellingand Fire Behaviour in Rooms.ISth Symposium (International)of Combustion, Toronto, August1980.
9
PETTERSSON, OVE FIRE HAZARDS AND THE COMPARTMENT FIRE GROWTH PROCESS-OUTLlNE OF A SWEDISH JOINT RESEARCH PROGRAM R80-5
>,