Upload
vanquynh
View
213
Download
0
Embed Size (px)
Citation preview
File E67601 Vol. 2 Index Page 1 Issued: 2017-03-24 INDEX
Construction United States Types Canadian Types Sec.
PVC Parallel Cord SPT-1, SPT-2, SPT-3, NISPT-1, NISPT-2
SPT-1, SPT-2, SPT-3, NISPT-1, NISPT-2 1
PVC Jacketed CordSVT, SVTO, SJT, ST, SJTO, STO, SJTW, STW,
SJTOW, STOW
SVT, SVTO, SJT, ST, SJTO, STO, SJTW, STW,
SJTOW, STOW 2
CABLE-UL-VOLEX-JEM 1/4
File E67601 Vol 2 Auth. Page 1 Issued: 2017-03-20 Revised: 2017-03-24 FOLLOW-UP SERVICE PROCEDURE (TYPE L) FLEXIBLE CORD (ZJCZ,ZJCZ7) Manufacturer: SEE ADDENDUM FOR MANUFACTURER LOCATIONS 197624 (Party Site) Applicant: Volex (Asia) Pte Ltd (337951-004) 35 TAMPINES ST 92 SINGAPORE 528880 SINGAPORE 197624 (Party Site) Listee/Classified Co.: SAME AS APPLICANT (337951-004) This Follow-Up Service Procedure authorizes the above Manufacturer(s) to use the marking specified by UL LLC, or any authorized licensee of UL LLC, including the UL Contracting Party, only on products when constructed, tested and found to be in compliance with the requirements of this Follow-Up Service Procedure and in accordance with the terms of the applicable service agreement with UL Contracting Party and any applicable Service Terms. The UL Contracting Party for Follow-Up Services is listed on addendum to this Follow-Up Service Procedure ("UL Contracting Party"). UL Contracting Party and UL LLC are referred to jointly herein as "UL." UL further defines responsibilities, duties and requirements for both Manufacturers and UL representatives in the document titled, "UL Mark Surveillance Requirements" that can be located at the following web-site: http://www.ul.com/fus and in the document titled "UL and Subscriber Responsibilities" that can be located at the following website: http://www.ul.com/responsibilities. Manufacturers without Internet access may obtain the current version of these documents from their local UL customer service representative or UL field representative. For assistance, or to obtain a paper copy of these documents or the applicable Service Terms, please contact UL's Customer Service at http://ul.com/aboutul/locations/, select a location and enter your request, or call the number listed for that location. The Applicant, the specified Manufacturer(s) and any Listee/Classified Co. in this Follow-Up Service Procedure must agree to receive Follow-Up Services from UL Contracting Party. If your applicable agreement is a Global Services Agreement ("GSA") with an effective date of January 1, 2012 or later and this Follow-Up Service Procedure is issued on or after that effective date, the Applicant, the specified Manufacturer(s) and any Listee/Classified Co. will be bound to a Service Agreement for Follow-Up Services upon the earliest by any Subscriber of use of the prescribed UL Mark, acceptance of the factory inspection, or payment of the Follow-Up Service fees which will incorporate such GSA, this Follow-Up Service Procedure and the Follow-Up Service Terms which can be accessed by clicking here: http://www.ul.com/contracts/Terms-After-12-31-2011. In all other events, Follow-Up Services will be governed by and incorporate the terms of your applicable service agreement and this Follow-Up Service Procedure.
CABLE-UL-VOLEX-JEM 2/4
File E67601 Vol 2 Auth. Page 2 Issued: 2017-03-20 Revised: 2017-03-24 It is the responsibility of the Listee/Classified Co. to make sure that only the products meeting the aforementioned requirements bear the authorized Marks of UL LLC, or any authorized licensee of UL LLC. This Follow-Up Service Procedure contains information for the use of the above Manufacturer(s) and representatives of UL and is not to be used for any other purpose. It is provided to the Manufacturer with the understanding that it will be returned upon request and is not to be copied in whole or in part. This Follow-Up Service Procedure, and any subsequent revisions, is the property of UL and is not transferable. This Follow-Up Service Procedure contains confidential information for use only by the above named Manufacturer(s) and representatives of UL and is not to be used for any other purpose. It is provided to the Subscribers with the understanding that it is not to be copied, either wholly or in part unless specifically allowed, and that it will be returned to UL, upon request. Capitalized terms used but not defined herein have the meanings set forth in the GSA and the applicable Service Terms or any other applicable UL service agreement. UL shall not incur any obligation or liability for any loss, expense or damages, including incidental, consequential or punitive damages arising out of or in connection with the use or reliance upon this Follow-Up Service Procedure to anyone other than the above Manufacturer(s) as provided in the agreement between UL LLC or an authorized licensee of UL LLC, including UL Contracting Party, and the Manufacturer(s). UL LLC has signed below solely in its capacity as the accredited entity to indicate that this Follow-Up Service Procedure is in compliance with the accreditation requirements. Bruce A. Mahrenholz Director North American Certification Program
CABLE-UL-VOLEX-JEM 3/4
File E67601 Vol 2 Addendum To Page 1 Issued: 2017-03-20 Authorization Page Revised: 2017-03-24 LOCATION 1640606 (Party Site) Volex-JEM Cable Precision (Dongguan) Co., Ltd No. 406, Qing Feng Road , Qingxi Town, Guangdong Province Dongguan City CHINA Factory ID: Volex-J or VLX-J UL Contracting Party for above site is: UL AG
CABLE-UL-VOLEX-JEM 4/4
DQD 507 Rev. 2016-02-18 Page 1
Certificate of Compliance Certificate: 70111963 Master Contract: 172976
Project: 70111963 Date Issued: 2017-04-07
Issued to: Volex (Asia) Pte Ltd.
35 Tampines St 92
Singapore, 528880
SINGAPORE
Attention: Joyce Teo
The products listed below are eligible to bear the CSA Mark shown
Issued by: Wilson Wang
Wilson Wang
PRODUCTS
CLASS - C583101 - WIRES-Flexible Cord
Types SPT-1, SPT-2, SPT-3, 300V, rated 60C, 75°C, 90°C and 105C, FT1, FT2 and VW-1.
Types NISPT-1, NISPT-2, 300V, rated 60C, 75°C, 90°C and 105C, FT1, FT2 and VW-1.
Types SVT, SVTO, 300V, rated 60C, 75°C, 90°C and 105C, FT1, FT2 and VW-1.
Types SJT,SJTO, SJTW, SJTOW, 300V, rated 60C, 75°C, 90°C and 105C, FT1, FT2 and VW-1.
Types ST, STO, STW, STOW, 600V, rated 60C, 75°C, 90°C and 105C, FT1, FT2 and VW-1.
APPLICABLE REQUIREMENTS
CSA Standard C22.2 No. 49 - Flexible Cords and Cables
CABLE-CSA-VOLEX-JEM 1/2
DQD 507 Rev. 2016-02-18 Page 1
Supplement to Certificate of Compliance
Certificate: 70111963 Master Contract: 172976
The products listed, including the latest revision described below,
are eligible to be marked in accordance with the referenced Certificate.
Product Certification History
Project Date Description
70111963 2017-04-07 Original Certification of Flexible cord, Types SPT-1, SPT-2, SPT-3, NISPT-
1, NISPT-2, SVT, SVTO, SJT, SJTO, SJTW, SJTOW, 300V and ST, STO,
STW, STOW, 600V, rated at 60°C, 75°C, 90°C and 105°C, FT1, FT2 and
VW-1, with PVC insulation “CT105”. CSA Standard C22.2 No. 49-14.
CABLE-CSA-VOLEX-JEM 2/2
2016/4/20 ZJCZ.E84516 - Flexible Cord
http://database.ul.com/cgi-bin/XYV/template/LISEXT/1FRAME/showpage.html?name=ZJCZ.E84516&ccnshorttitle=Flexible+Cord&objid=1074132793&cfgi… 1/1
ZJCZ.E84516Flexible Cord
Page Bottom
Flexible Cord
See General Information for Flexible Cord
TA HSING INDUSTRIES LTD E84516
10F-16 6 Ln 180 Sec 6 Minquan E Rd
Neihu District
Taipei, 114 TAIWAN
Decorative cord, Type(s) CXTW, SPT-1W, SPT-2W, XTW
Jacketed cord, Type(s) SE, SJE, SJT, SJTO, SJTOO, SJTOW, SJTW, ST, STO, STOO, STOOW, STOW, STW, SVE, SVT,SVTO, SVTOO
Parallel cord, Type(s) NISPE-1, NISPE-2, NISPT-1, SPE-1, SPE-2, SPE-3, SPT-1, SPT-2, SPT-3
Special-use cord, Type(s) C
Tinsel cord, Type(s) TPT, TST
Last Updated on 2015-01-16
Questions? Print this page Terms of Use Page Top
� 2016 UL LLC
The appearance of a company's name or product in this database does not in itself assure that products soidentified have been manufactured under UL's Follow-Up Service. Only those products bearing the UL Mark shouldbe considered to be Certified and covered under UL's Follow-Up Service. Always look for the Mark on the product.
UL permits the reproduction of the material contained in the Online Certification Directory subject to the followingconditions: 1. The Guide Information, Assemblies, Constructions, Designs, Systems, and/or Certifications (files) mustbe presented in their entirety and in a non-misleading manner, without any manipulation of the data (or drawings).2. The statement "Reprinted from the Online Certifications Directory with permission from UL" must appear adjacentto the extracted material. In addition, the reprinted material must include a copyright notice in the following format:"© 2016 UL LLC".
2016/4/20 ZJCZ7.E84516 - Flexible Cord Certified for Canada
http://database.ul.com/cgi-bin/XYV/template/LISEXT/1FRAME/showpage.html?name=ZJCZ7.E84516&ccnshorttitle=Flexible+Cord+Certified+for+Canada… 1/1
ZJCZ7.E84516Flexible Cord Certified for Canada
Page Bottom
Flexible Cord Certified for Canada
See General Information for Flexible Cord Certified for Canada
TA HSING INDUSTRIES LTD E84516
10F-16 6 Ln 180 Sec 6 Minquan E Rd
Neihu District
Taipei, 114 TAIWAN
Jacketed cord, Type(s) SJT, SJT(TPE), SJTO, SJTOO, SJTOW, SJTW, ST, ST(TPE), STO, STOO, STOOW, STOW, STW,SVT, SVT(TPE), SVTO, SVTOO
Parallel cord, Type(s) NISPT-1, NISPT-1(TPE), NISPT-2(TPE), SPT-1, SPT-1(TPE), SPT-2, SPT-2(TPE), SPT-3, SPT-3(TPE)
Tinsel cord, Type(s) TPT, TST
Last Updated on 2015-01-16
Questions? Print this page Terms of Use Page Top
� 2016 UL LLC
The appearance of a company's name or product in this database does not in itself assure that products soidentified have been manufactured under UL's Follow-Up Service. Only those products bearing the UL Mark shouldbe considered to be Certified and covered under UL's Follow-Up Service. Always look for the Mark on the product.
UL permits the reproduction of the material contained in the Online Certification Directory subject to the followingconditions: 1. The Guide Information, Assemblies, Constructions, Designs, Systems, and/or Certifications (files) mustbe presented in their entirety and in a non-misleading manner, without any manipulation of the data (or drawings).2. The statement "Reprinted from the Online Certifications Directory with permission from UL" must appear adjacentto the extracted material. In addition, the reprinted material must include a copyright notice in the following format:"© 2016 UL LLC".
2017/9/11 ZJCZ.E156136 - Flexible Cord
http://database.ul.com/cgi-bin/XYV/template/LISEXT/1FRAME/showpage.html?name=ZJCZ.E156136&ccnshorttitle=Flexible+Cord&objid=1074132723&cf… 1/1
ZJCZ.E156136Flexible Cord
Page Bottom
Flexible Cord
See General Information for Flexible Cord
SHENZHEN TONGYUAN ELECTRICAL WIRE & CABLE CO., LTD. E156136
TONGYUAN INDUSTRY ZONE, XIKENG NEW VILLAGE
FUMIN GUANLAN TOWN, LONGHUA
SHENZHEN, GUAGNDONG 518110 CHINA
Clock cord, Type(s) Clock
Decorative cord, Type(s) CXTW, SPT-1W, SPT-2W, XTW
Jacketed cord, Type(s) SE, SEO, SEOO, SEOOW, SEOW, SEW, SJE, SJEO, SJEOO, SJEOOW, SJEOW, SJEW, SJT, SJT-R,SJTO, SJTOO, SJTOOW, SJTOW, SJTW, ST, STO, STOO, STOOW, STOW, STW, SVE, SVT, SVT-R
Parallel cord, Type(s) NISPT-1, NISPT-2, SPT-1, SPT-2, SPT-2-R, SPT-3
Last Updated on 2017-09-08
Questions? Print this page Terms of Use Page Top
© 2017 UL LLC
The appearance of a company's name or product in this database does not in itself assure that products soidentified have been manufactured under UL's Follow-Up Service. Only those products bearing the UL Mark shouldbe considered to be Certified and covered under UL's Follow-Up Service. Always look for the Mark on the product.
UL permits the reproduction of the material contained in the Online Certification Directory subject to the followingconditions: 1. The Guide Information, Assemblies, Constructions, Designs, Systems, and/or Certifications (files) mustbe presented in their entirety and in a non-misleading manner, without any manipulation of the data (or drawings).2. The statement "Reprinted from the Online Certifications Directory with permission from UL" must appear adjacentto the extracted material. In addition, the reprinted material must include a copyright notice in the following format:"© 2017 UL LLC".
CABLE-UL-BH(SZ) 1/3
NOTICE OF AUTHORIZATION TO APPLY THE UL MARK
This is an electronically generated letter. Signatures are not required for this document to be valid. Page 1 of 2
05/10/2010 Shenzhen Bao Hing Electric Wire & Cable Mfr Co Ltd Mr. Jiadong Luo Buchong Tongfuyu Industry Area Shajing Rd Shajing St Baoan District Shenzhen Guangdong 518104, Cn
Our Reference: File E159216, Vol. 1 Project Number 10CA22625 Your Reference: MS. LUO ACCEPTED ON 30 APR 10 Project Scope: UL/CUL: TPE Flexible Cord, Types SVE, SVT, SJE, SJT, NISPE-1, NISPT-1 NISPE-2 and
NISPT-2, 18 AWG conductor, may employ rayon yarns with 200-500 denier within copper conductor strands
Dear Mr. Jiadong Luo:
UL's investigation of your product(s) has been completed under the above Reference Number and the product was determined to comply with the applicable requirements.
This letter temporarily supplements the UL Follow-Up Services Procedure and serves as authorization to apply the UL Mark only at authorized factories under UL's Follow-Up Service Program.
To provide the manufacturer with the intended authorization to use the UL Mark, the addressee must send a copy of this notice to each manufacturing location currently authorized in File E159216, Vol. 1.
This authorization is effective from the date of this Notice and only for products at the indicated manufacturing locations. Records in the Follow-Up Services Procedure covering the product are now being prepared and will be sent in the near future. This letter authorizes application of the UL Mark for 90 days from the date of this letter.
Products that bear the UL Mark shall be identical to those that were evaluated by UL and found to comply with UL’s requirements. If changes in construction are discovered, appropriate action will be taken for products not in conformance with UL’s requirements and continued use of the UL Mark may be withdrawn. UL may elect to withdraw use of the UL Mark if the Applicant or Manufacturer fails to comply with UL’s requirements including ongoing compliance of the product, under UL’s Follow-Up Service.
CABLE-UL-BH(SZ) 2/3
Notice of Authorization - 10CA22625
This is an electronically generated letter. Signatures are not required for this document to be valid. Page 2 of 2
Any information and documentation provided to you involving UL Mark services are provided on behalf of Underwriters Laboratories Inc. (UL) or any authorized licensee of UL.
The contents of this Letter are intended solely for the use of UL and the Applicant. The opinions and findings of UL represent its judgment given with due consideration to the necessary limitations of practical operation in accordance with UL’s objectives and purposes. UL shall not otherwise be responsible for the use of or reliance upon the contents of this letter by anyone. UL shall not incur any obligation or liability for any loss, expense or damages, including incidental, consequential or punitive damages, arising out of or in connection with the use or reliance upon the contents of this letter to anyone other than the Applicant as provided in the agreement between UL and Applicant. Any use or reference to UL’s name or certification mark(s) by anyone other than the Applicant in accordance with the agreement is prohibited without the express written approval of UL.
Very truly yours, Reviewed by:
Jacky Lam Dan Chan+852 2276 9296 +852 2276 9573Engineer Project Engineer [email protected] [email protected]
GUZCAE9-242C58
CABLE-UL-BH(SZ) 3/3
CABLE-CSA-BH 1 / 6
CABLE-CSA-BH 2 / 6
CABLE-CSA-BH 3 / 6
CABLE-CSA-BH 4 / 6
CABLE-CSA-BH 5 / 6
CABLE-CSA-BH 6 / 6
File E62405SP Vol 1 Auth. Page 1 Issued: 1982-01-06
Revised: 2017-08-04
FOLLOW-UP SERVICE PROCEDURE
(TYPE R)
UNLISTED COMPONENT
ATTACHMENT PLUGS, FUSELESS
(AXUT3,AXUT9)
Manufacturer: SEE ADDENDUM FOR MANUFACTURER LOCATIONS
197624 (Party Site)
Applicant: Volex (Asia) Pte Ltd
(337951-004) 35 TAMPINES ST 92
SINGAPORE 528880 SINGAPORE
This Follow-Up Service Procedure authorizes the above Manufacturer(s) to use the marking
specified by UL LLC, or any authorized licensee of UL LLC, including the UL Contracting
Party, only on products when constructed, tested and found to be in compliance with the
requirements of this Follow-Up Service Procedure and in accordance with the terms of the
applicable service agreement with UL Contracting Party and any applicable Service Terms. The
UL Contracting Party for Follow-Up Services is listed on addendum to this Follow-Up Service
Procedure ("UL Contracting Party"). UL Contracting Party and UL LLC are referred to jointly
herein as "UL."
UL further defines responsibilities, duties and requirements for both Manufacturers and UL
representatives in the document titled, "UL Mark Surveillance Requirements" that can be
located at the following web-site: http://www.ul.com/fus and in the document titled "UL and
Subscriber Responsibilities" that can be located at the following website:
http://www.ul.com/responsibilities. Manufacturers without Internet access may obtain the
current version of these documents from their local UL customer service representative or UL
field representative. For assistance, or to obtain a paper copy of these documents or the
applicable Service Terms, please contact UL's Customer Service at
http://ul.com/aboutul/locations/, select a location and enter your request, or call the
number listed for that location.
The Applicant and the specified Manufacturer(s) in this Follow-Up Service Procedure must
agree to receive Follow-Up Services from UL Contracting Party. If your applicable agreement
is a Global Services Agreement ("GSA") with an effective date of January 1, 2012 or later
and this Follow-Up Service Procedure is issued on or after that effective date, the
Applicant and the specified Manufacturer(s) will be bound to a Service Agreement for Follow-
Up Services upon the earliest by any Subscriber of use of the prescribed UL Mark, acceptance
of the factory inspection, or payment of the Follow-Up Service fees which will incorporate
such GSA, this Follow-Up Service Procedure and the Follow-Up Service Terms which can be
accessed by clicking here: http://www.ul.com/contracts/Terms-After-12-31-2011. In all other
events, Follow-Up Services will be governed by and incorporate the terms of your applicable
service agreement and this Follow-Up Service Procedure.
PLUG-CONN-RECEPTACLES-UL 1/11
File E62405SP Vol 1 Auth. Page 2 Issued: 1982-01-06
Revised: 2017-08-04
It is the responsibility of the Manufacturer to make sure that only the products meeting the
aforementioned requirements bear the authorized Marks of UL LLC, or any authorized licensee
of UL LLC.
This Follow-Up Service Procedure contains information for the use of the above
Manufacturer(s) and representatives of UL and is not to be used for any other purpose. It is
provided to the Manufacturer with the understanding that it will be returned upon request
and is not to be copied in whole or in part.
This Follow-Up Service Procedure, and any subsequent revisions, is the property of UL and is
not transferable. This Follow-Up Service Procedure contains confidential information for use
only by the above named Manufacturer(s) and representatives of UL and is not to be used for
any other purpose. It is provided to the Subscribers with the understanding that it is not
to be copied, either wholly or in part unless specifically allowed, and that it will be
returned to UL, upon request.
Capitalized terms used but not defined herein have the meanings set forth in the GSA and the
applicable Service Terms or any other applicable UL service agreement.
UL shall not incur any obligation or liability for any loss, expense or damages, including
incidental, consequential or punitive damages arising out of or in connection with the use
or reliance upon this Follow-Up Service Procedure to anyone other than the above
Manufacturer(s) as provided in the agreement between UL LLC or an authorized licensee of UL
LLC, including UL Contracting Party, and the Manufacturer(s).
UL LLC has signed below solely in its capacity as the accredited entity to indicate that
this Follow-Up Service Procedure is in compliance with the accreditation requirements.
Bruce A. Mahrenholz
Director
North American Certification Program
PLUG-CONN-RECEPTACLES-UL 2/11
File E62405SP Vol 1 Addendum To Page 1 Issued: 1982-01-06
Authorization Page Revised: 2017-08-04
LOCATION
175031 (Party Site)
(342882-001) VOLEX CABLE ASSEMBLY (VIETNAM) CO LTD
D-5B THANG LONG INDUSTRIAL PARK
DONG ANH DISTRICT
HANOI VIETNAM
Factory ID: VH
UL Contracting Party for above site is: UL AG
202099 (Party Site)
(221809-001) PT VOLEX INDONESIA
JALAN IR SUTAMI, KAWASAN INDUSTRI SEKUPANG
BATAM 29422 INDONESIA
Factory ID: B
UL Contracting Party for above site is: UL AG
21297 (Party Site)
(918517-001) Volex Cable Assembly (Zhongshan) Co Ltd
2 Xingda St
Torch Development Zone
ZHONGSHAN
GUANGDONG 528437 CHINA
Factory ID: SM1 OR SMI
UL Contracting Party for above site is: UL AG
24462 (Party Site)
(902299-002) Volex De Mexico S A
Ave 32 Sur Num 8950
INTERIOR EDIFICIO G1, D, E, F
PARQUE INDUSTRIAL LA MESA, FRACC RUBIO
22650 Tijuana
BC MEXICO
Factory ID: TI
UL Contracting Party for above site is: UL AG
PLUG-CONN-RECEPTACLES-UL 3/11
File E62405SP Vol 1 Addendum To Page 2 Issued: 1982-01-06
Authorization Page Revised: 2017-08-04
LOCATION
28615 (Party Site)
(106395-001) Volex Cable Assembly (Shenzhen) Co Ltd
VOLEX BLDG
1173 SHENHUI RD
BAO'AN, HENGGANG
SHENZHEN
GUANGDONG 518115 CHINA
Factory ID: SM or HG
UL Contracting Party for above site is: UL AG
65729 (Party Site)
(788163-001) VOLEX INTERCONNECT (INDIA) PVT LTD
22-1A 1ST ST
KHAZURA GARDEN
NEELANGARAI
CHENNAI Tamil Nadu 600041 INDIA
Factory ID: VC
UL Contracting Party for above site is: UL India Private Limited
PLUG-CONN-RECEPTACLES-UL 4/11
File E62405SP Vol. 1 Index Page 1 Issued: 1989-07-11
Revised: 2015-09-11
INDEX
ATTACHMENT PLUG:
Models Section Report Date
Unlisted component, Attachment-Plug Cap! Cat.
No.ME301.
1 1976-12-23
NEMA CONFIGURATION
Cat. No. Config. Cord AWG Electrical A/V Sec. Fig. USU CNU
ME301, -D, -
P, -S, -R, -
RP
1-15 20,18,17,16/2 7,10,10,13/125 2 1,1A Yes Yes
230619-001 1-15 18/2 5/125 2 1B Yes Yes
USJ15 1-15 18,16/2 7,10,13/125 2 1 Yes Yes
ME302, -B, -
P
1-15 18,17,16/2 10,12,13/125 2 2 Yes Yes
ME302GR 1-15 18,17,16/2 10,12,13/125 2 3 Yes Yes
US115LS, -
LPS, -S
1-15 18,16/2 10,13/125 2 4,6 Yes Yes
926 1-15 18,16,14/2 10,13,15/125 2 7 Yes Yes
926SR 1-15 18,16,14/2 10,13,15/125 2 Ill.13,14 Yes Yes
926NPSR 1-15 18,16,14/2 10,13,15/125 2 16 Yes Yes
926BSR 1-15 18,16,14/2 10,13,15/125 2 Ill.13,14,16 Yes Yes
DS15EPS2 1-15 18,17,16/2 10,12,13/125 2 21 Yes Yes
US115SC, -
PSC
1-15 18/2 7/125 3 16 Yes Yes
US15B, -P 1-15 18,16,14/2 10,13,15/125 2 4 Yes Yes
US15S2 1-15 18/2 10/125 2 Ill.17 Yes Yes
USJ15B 1-15 18/2 10/125 2 4 Yes Yes
MP128(EMI) 1-15 18/2 10/125 3 5 Yes Yes
VP129(EMI) 1-15 18/2 10/250 3 14 Yes Yes
US515SC(EMI) 5-15 16/3 13/125 3 21 Yes Yes
185, -F 5-15 18,16,14/3 10,13,15/125 2 -- Yes No
CX-490, -495 5-15 14,12,10/3 15,20,30/250 2 8 Yes No
3323(Hosp) 5-15 16,14/3 13,15/125 3 11,12 Yes Yes
3317 5-15 18,16/3 10,13/125 3 13 Yes Yes
AEC60(Hosp) 5-15 18,16,14,12/3 10,13,15,15/125 3 15 Yes Yes
PS204, -B, -
D
5-15 18,17,16,14/3 10,12,13,15/125 3 1 Yes Yes
PS204A 5-15 18,17,16,14/3 10,12,13,15/125 3 3 Yes Yes
US515A,
USI515A
5-15 18,16,14/3 10,13,15/125 3 17 Yes Yes
PS206 5-15 18,16,14/3 10,13,15/125 3 2 Yes Yes
PS206A -- 18,16 10,13 3 -- Yes Yes
PS515 5-15 18,16,14,12/3 10,13,15,20/125 3 10 Yes Yes
MP204 5-15 18,18,16,14/3 2.5,10,13,15,15/125 3 4 Yes Yes
USD15A, -
S15A
5-15 18,16/3 10,13/125 3 9 Yes Yes
PS520
5-20 18,16, 18,16,
14,12/314,12/3
10,13, 18,20/125 3 10 Yes Yes
PLUG-CONN-RECEPTACLES-UL 5/11
File E62405SP Vol. 1 Index Page 1A Issued: 1989-07-11
Revised: 2016-06-01
ATTACHMENT PLUG: (Cont’d)
NEMA CONFIGURATION
Cat. No. Config. Cord AWG Electrical A/V Sec. Fig. USU CNU
1541 L5-20 18,16,14/3 10,13,15/125 3 20 Yes No
VS205A 6-15 18,16,14/3 10,13,15/250 3 8 Yes Yes
VS205S 6-15 18,16,14/3 10,13,15/250 3 Ill.55,56 Yes Yes
PS615 6-15 18,16,14,12/3 10,13,15,20/250 3 10 Yes Yes
PS620 6-20 18,16,14,12/3 10,13,18,20/250 3 10 Yes Yes
VS207A 6-20 14,12/3 15,20/250 3 6 Yes Yes
VS208A 6-30 12/3 25/250 3 7 Yes Yes
PL3001 1-15 18/2 10/125 3 23 Yes Yes
PL3007 1-15 14/3 15/125 3 -- Yes Yes
PS206A 5-15 18,16/3 10,13/125 3 24 Yes Yes
US650A, US650A
(A.C.1)
6-50 12/3 25/250 3 25,33 Yes Yes
US15S3 5-15 18/3 10/125 3 Ill.51 Yes Yes
MA115VPS2 1-15 18, 16/2 10,15/125 9 Ill.1 Yes Yes
USL620PS3 L6-20 14,12/3 15,20/250 3 26 Yes Yes
VPUS15S3 5-15 18,16/3 10,13/125 3 27 Yes Yes
US515NGA3,
US515EGA3, US515SGA3,
US515WGA3
5-15 18,16,14 10,13,15/125 3 28 YES YES
US515BTA3 5-15 18,16 10,13/125 3 29 YES YES
VPUS15DS3 5-15 18,16 10,13/125 3 - YES YES
US15GPS2 1-15 17,16 12,13/125 2 9 YES YES
USJ15TS3 5-15 18,16,14 10,13,15/125 3 30 YES YES
US115VPS2 1-15 18,17 10,12/125 2 13 YES YES
US115DPS2 1-15 17 12/125 2 10 YES YES
RA115GRP 1-15 18,17,16 10,12,13/125 2 11 YES YES
USL520PS3 L5-20 18,16,14,12 10,13,15,20/125 3 31 YES YES
PS520A 5-20 12 20/125 3 32 YES YES
US115VS2 1-15 18,17 10,12/125 2 12 YES YES
VPUS15S2 1-15 18/2 10/125 2 14 YES YES
USD15GPS2 1-15 18,17,16/2 10,12,13/125 2 15 YES YES
USD115PS2 1-15 17/2 12/125 2 16 YES YES
APUS15S3 5-15 18,16/3 10,13/125 3 34 YES YES
DS15PS2 1-15 18, 17, 16/2 10,12,13/125 2 17 YES YES
ME301SH 1-15 18 10/125 2 18 YES YES
APUS15S2 1-15 18/2 10/125 2 19 YES YES
US15PA2 1-15 18/2 10/125 2 20 YES YES
US520A3 5-20P 12/3 20/125 3 35,36 YES YES
US15TS2 1-15 18/2 10/125 2 22 YES YES
DS15JPS2 1-15P 18,17,16/2 10,12,13/125 2 23 YES YES
HO515S3 5-15P 16/3 13/125 3 37 YES -
MFUS15S2 1-15 18/2 2.5,7/125 2 24 YES YES
AP7J34 1-15 18/2 10/125 2 25 YES YES
DLUS15S3 5-15 18/3 7/125 9 1 YES YES
VNUS15S3 5-15 18,16/3 2.5,10,13/125 2 26 YES YES
VNUS15FS3 5-15 18/3 2.5,10/125 2 -- YES YES
VNUS15S2 1-15 18/2 7, 10/125 2 27 YES YES
USL515PS3 L5-15 14/3 15/125 3 38 YES YES
USL2130PS L21-30P 10/5 25/120/208, 3 3 39 YES NO
USL630PS L6-30 10,9/3 30,30/250 3 40 YES YES
Note: (A.C.1) – ALTERNATE CONSTRUCTION NO. 1.
PLUG-CONN-RECEPTACLES-UL 6/11
File E62405SP Vol. 1 Index Page 1B Issued: 1989-07-11
Revised: 2017-12-15
ATTACHMENT PLUG (Cont’d): NEMA CONFIGURATION
Cat. No. Config. Cord AWG Electrical A/V Sec. Fig. USU CNU
CSUS15S3 5-15P 18,16/3 10,13/125 9 2 Yes Yes
DGUSJ515HS3 5-15P 18,14/3 10,15/125 3 41 Yes Yes
APUSC138S2 1-15P 18/2 10/125 9 3 Yes Yes
US515AD 5-15P 18,18/3 2.5,10/125 3 42 Yes Yes
MLUS15S2 1-15P 18/2 2.5/125 9 4 Yes Yes
IEC CONFIGURATION
Cat. No. Config. Cord AWG Electrical A/V Sec. Fig. USU CNU
PS25A C14 18/3 10/250 5 1 YES YES
PS25 C14 18/3 10/250 5 2 YES YES
SSD10A C14 18,16/3 10,13/250 5 3 YES YES
3318-M3 C14 18,16/3 10,13/250 5 4 YES YES
3321A,-B C14 18,16/3 10,13/250 5 4 YES YES
3322A,-B C14 18,16/3 10,13/250 5 4 YES YES
APC14 C14 18/3 10/250 5 6 YES YES
VAC14A, VAC14S
C14 18,17/3 10,12/125 or 250 5 9 YES YES
C14 17/3 12/125 or 250 5 9 YES YES
VAC14BS C14 16/3 13/250 5 9 YES YES
VAC14LS C14 16/3 10,13/125 or 250 5 Ill.32 YES YES
14/3 15,16/125 or 250
94110/2 EuroPlug 18/2 2.5/250 5 5 YES YES
201492-1 C14/C7(2) 18/2 7/250 5 7,8 YES YES
VSC20 C20 16,14,12/3 13,16,20/250 5 10 YES YES
PL3004 C14 16/3 13/125 or 250 5 11 YES YES
VAC20S C20 16,14/3 13,16/125 or 250 5 12 YES YES
VAC20A C20 16,14/3 13,15,16/125 or 250 5 20 YES YES
VAC14KC C14 18,16/3 10,13/125 or 250 5 21 YES YES
VAC20KC C20 14/3 16/125 or 250 5 22 YES YES
VAC20BS C20 12/3 16,20/125 or 250 5 23 YES YES
VAC14LA C14 18,16,14/3 10,13,15/125 or 250 5 24 YES YES
VAC20AD C20 14,12/3 16,20/125 or 250 5 25 YES YES
VAC14KAL C14 18,16/3 10,13/125 or 250 5 26 YES YES
VAC14KAR C14 18,16/3 10,13/125 or 250 5 27 YES YES
VAC20KAR C20 16,14,14/3 13,15,16/125 or 250 5 28 YES YES
VAC20KAL C20 16,14,14/3 13,15,16/125 or 250 5 29 YES YES
SMC14LA C14 18,16/3 10,13/125 or 250 5 30 YES YES
VNC14S C14 18,17,16/3 10,12,13/125 or 250 5 31 YES YES
VAC14S C14 18,17/3 10,12/125 or 250 5 32 YES YES
VNC14BS C14 17,17,16/3 10,12,13/125 or 250 5 33 YES YES
PLUG-CONN-RECEPTACLES-UL 7/11
File E62405SP Vol. 1 Index Page 2 Issued: 1989-07-11
Revised: 2017-06-30
CORD CONNECTOR BODIES:
NEMA CONFIGURATION
Cat. No.
Config
. Cord AWG Electrical A/V Sec. Fig. CUL
US115RPS 1-15 18/2 10/125 7 1 Yes
US515RP 5-15 18/3 10/125 7 2 Yes
US515RS,
US515RS(A.C.1) 5-15 18,16,14/3 10,13,15/125 4 30,51 Yes
AEC-212, AEC-202,-
210, 5-15 18,16,14/3 10,13,15/125 4 32 Yes
28-9170 1-15 18,16,14/3 10,13,15/125 4 32 Yes
CN-4008 5-15 16, 14/3 13,15/125 4 38 Yes
PH-161 1-15 18,16,14/2 10,13,15/125 4 44,45,
46 No
US515RP-A 5-15 18/3 10/125 7 3 Yes
Note: (A.C.1) – ALTERNATE CONTRUCTION NO. 1.
IEC CONFIGURATION
Cat. No. Config. Cord AWG Electrical A/V Sec. Fig. CUL
PS625,-A,-LA C13 18,16,14/3 10,13,15/125 4 1 Yes
PS309,-P C1 18/2 7/125 4 2 Yes
M1625 C13 18,16/3 10,13/125 or 250 4 3,3A Yes
VIC13A C13 18,16/3 10,13/125 or 250 4 3C
V1625 C13 18,18,17,16/
3
2.5,10,12,13/125 or
250 4 3, 3A Yes
V1625BS
C13 16,14,14/3 13,15,16/125 or 250 4 3B Yes
VAC13KS C13
18/3
16/3
14/3
10/125 or 250
13/125 or 250
15/125 or 250
4 3D Yes
M1250A,-P C7 18/2 7/250 4 4 Yes
M1250R C7 18/2 7/250 4 4A Yes
MS212,-A C9 18/2 10/125 4 5 Yes
MS225 C17 18/2 10/125 4 6 Yes
VAC17S,VAC17BS,
PIC17S, PIC17BS C17 18,16,14/2 10,13,15/125 4 6A Yes
YAC17S C17 18/2 10/125 4 6A Yes
VAC17A C17 16/2 10,13/125 4 6C Yes
M2825 C15,
C15A 18,16/3 10,15(HPN)/125 4 7 Yes
VAC15A C15 16,14/3 13, 16/125 or 250 4 52 Yes
VAC15S C15 18,16,14/3 10,13,15/250 (HPN) 4 7 Yes
VAC15BS C15 18,16,14/3 10,13,15/250 4 7 Yes
18 10/125 (SJ)
25AC5, 25ARAC5 C5 18/3 2.5,7/125 or 250 4 8 Yes
VAC5S,-AL,-AR C5 18/3 2.5,7/125 or 250 4 8 Yes
V1625LA C13 18,17,16,14/
3
10,12,13,15/125 or
250 4 9 Yes
V1625A C13 18,17,16/3 10,12,13/125 or 250 4 9 Yes
V1625BA C13 16,14/3 13,15/125 or 250 4 9A Yes
PLUG-CONN-RECEPTACLES-UL 8/11
File E62405SP Vol. 1 Index Page 2A Issued: 1989-07-11
Revised: 2013-03-13
CORD CONNECTOR BODIES CON’T:
IEC CONFIGURATION
Cat. No. Config. Cord AWG Electrical A/V Sec. Fig. CUL
AVLC13 C13 18,16,14,14/3 10,13,15,16/125 or 250
4 9B Yes
AVRC13 C13 18,16,14/3
10,13,15/125 or
250 4 9B Yes
3318-F3 C13 18,16/3 10,13/125 4 10 Yes
3319A,-B C13 18,16/3 10,13/125 4 10 Yes
3320A,-B C13 18,16/3 10,13/125 4 10 Yes
VSC15,VRC15,VLC15 C15 18,17,16,14/3 10,10,13,15/250 4 11 Yes
VSC13,VRC13,VLC13 C13 18,17,16,14/3 10,10,13,15/250 4 11 Yes
VSCC13 C13 18/3 10/250 4 11A Yes
VSC19,VRC19,VLC19 C19 18,16,14,12/3 10,13,16,20/250 4 12 Yes
VSCC19 C19 18,16,14,12/3 10,13,16,20/250 4 -- Yes
8393 Spec. 18/3 10/125 4 13 Yes
HS10S,-U C13 18,16/3 10,13/250 4 14 Yes
HS10A,-U C13 18,16/3 10,13/250 4 15 Yes
Z357316 C17 18/2 10/125 4 -- Yes
Z357318 C13 18/2 10/250 4 16 Yes
16SCI C19 16/3 13/250 4 17 Yes
AP19M18 C19 14/3 15/125 8 1 Yes
APC13 C13 18,16/3 10,13/250 4 18 Yes
APC13S C13 18/3 10/250 4 31 Yes
APC5A C5 18/3 10/125 4 19 Yes
APC5M C5 18/2 10/125 4 20 Yes
APC7M C7 18/2 2.5/125 4 29 Yes
APC5S, -5SM C5 18/3 10/125 4 21 Yes
VAC7PS C7 18/2 7/125 4 23 Yes
VAC7S, SZC7S C7 18/2 2.5,7/125 or 250 4 23 Yes
VAC7A C7 18/2 7/125 4 24 Yes
APC7S C7 18/2 2.5/125 or 250 4 25 Yes
APC7Q C7 18/3(Functional Ground)
2.5/125 4 35 Yes
VAC19 C19 16,14,12/3 13,15,20/250 4 26 Yes
VAC19A, VAC19LA C19 16,14,12/3 13,15,20/125 or 250
4 65 Yes
APC5SP, -SF C5 18/3 2.5/250 4 27 Yes
CN-4001 C17 18/2 10/125 4 28 Yes
CN-4002 C13(Special Use)
16/3 13/125 or 250 4 36 Yes
APC13F C13(Special Use)
18,16/3 10,13/125 4 37 Yes
APC13G C13(Special Use)
18/3 10/125 or 250 4 39 Yes
APC13H C13(Special
Use) 18/3 10/125 or 250 4 53 Yes
DLC7U2 C7 18/2 2.5/125 4 - Yes
DLC5U3 C5 18 2.5/125 4 - Yes
AP7M16 C7 18 2.5/125 4 - Yes
APC13FH C13(Special Use)
16/3 13/125 4 62 Yes
PLUG-CONN-RECEPTACLES-UL 9/11
File E62405SP Vol. 1 Index Page 2B Issued: 1989-07-11
Revised: 2017-12-15
CORD CONNECTOR BODIES CON’T:
IEC CONFIGURATION
Cat. No. Config. Cord AWG Electrical A/V Sec. Fig. CUL
VCC13 C13 18/3 10/125 4 40 Yes
VAC19KS C19 14, 14,12/3 15,16,20/125 or 250 4 41 Yes
SOC7S C7 18/2 7/125 4 42 Yes
APC13GH C13 18/3 10/125 4 43 Yes
HPC13A C13 18,16/3 10,13/250 4 47 Yes
DLC7E2 C7 18/2 2.5/125 4 48 Yes
DLC5E3 C5 18/3 2.5/125 4 49 Yes
V1625AT C13 18/3 10/250 4 50 Yes
VCC7S C7 18/2 3,7/125 or 250 4 54 Yes
VCC5S C5 18/3 2.5/125 or 250 4 55 Yes
APC7H C7 18/3(Functional Ground)
2.5/125 4 56 Yes
VCC5AR C5 18/3 2.5/125 or 250 4 57 Yes
VCC13A C13 18/3 10/125 or 250 4 58 Yes
V1625H C13 18,16/3 10,13/125 or 250 4 59 Yes
VAC19H C19 14,14,12/3 15,16,20/125 or 250 4 60 Yes
APC7K C7 18/2 2.5/125 4 61 Yes
VCC7 C7 18/2 7/125 or 250 4 63 Yes
HOC13S C13 16/3 13/125 or 250 4 64 Yes
VAC17KS C17 18/2 10/125 or 250 4 66 Yes
VAC13CS, VAC13AU
C13 18/3 10/125 or 250 4 68 Yes
VAC13AD C13 18,16/3 10,13/125 or 250 4 68 Yes
APC7KC C7 18/2 2.5/125 10 1 Yes
APC13HC C13 18/3 10/125 10 2 Yes
MFC7S C7 18/2 2.5/125 10 3 Yes
APC13HJ C13 18/3 10/125 10 4 Yes
APC7HB C7 18/3(Functional Ground)
2.5/125 10 5,6 Yes
VCS3KS Non-
Stanard
18/3 2.5/125 or 250 10 7 Yes
VAS3KS Non-Stanard
18/3 2.5/125 or 250 10 8 Yes
APC7J C7 18/2 2.5/125 4 67 Yes
DLC5CS3 C5 18/3 7/125 10 9 Yes
VNC7S C7 18/2 7/125 10 10 Yes
VNC5S C5 18/3 2.5/125 or 250 10 11 Yes
VNC5FS C5 18/3 2.5/125 or 250 10 12 Yes
VNC13S C13 18,17,16/3 10,12,13/125 or 250 10 13 Yes
VNC13A C13 18,16/3 10,13/125 or 250 10 15 Yes
VNC7A C7 18/2 7/125 10 14 Yes
VAC19A120, VAC19LA120
C19 12/3 16/125 or 250 4 69 Yes
DGC13A C13 18/3 10/ 125 or 250 4 70 Yes
DGC13S C13 18/3 10/ 125 or 250 4 71 Yes
DGC19S C19 14/3 15/ 125 or 250 4 72 Yes
HPC5DC C5 18/3 7 / 125 10 12 Yes
VAC7SR C7 18/2 7/125 4 - Yes
VNC21S C21 14/3 16/250 11 1 Yes
MLC7S C7 18/2 2.5/125 10 17 Yes
PLUG-CONN-RECEPTACLES-UL 10/11
File E62405SP Vol. 1 Index Page 3 Issued: 1989-07-11
Revised: 2010-09-08
NONSTANDARD CONFIGURATION
Cat. No. Config. Cord AWG Electrical A/V Sec. Fig. CUL
PHX-949 N/A 18,17/2 10,10/125 4 22 Yes
SR5008 N/A 16/3 13/125 4 33 Yes
DLC5A3 N/A 18/3 2.5/125 4 34 Yes
DLC5SA3 N/A 18/3 2.5/125 4 34A Yes
CORD SPLICES:
Cat. No. Config. Cord AWG Electrical A/V Sec. Fig. CUL
497-0420299 N/A 18,16/3 10,13/125 6 1,3 Yes
7594 N/A 18,16,14/3 10,13,15/250 6 2 Yes
Duo-Cord N/A 18,16,14/3 10,13,16/125 or 250 6 4 Yes
DUO-CORD-B N/A 14/3 16/125 or 250 6 6 Yes
Trident N/A 18,16,14/3 10,10,10/250 6 5 Yes
PLUG-CONN-RECEPTACLES-UL 11/11
PLUG-CSA 1/5
PLUG-CSA 2/5
PLUG-CSA 3/5
PLUG-CSA 4/5
PLUG-CSA 5/5
File E62405SP Vol 3 Auth. Page 1 Issued: 2000-01-05
Revised: 2012-03-06
FOLLOW-UP SERVICE PROCEDURE
(TYPE R)
UNLISTED COMPONENT
ATTACHMENT PLUGS, FUSELESS
(AXUT3)
Manufacturer: SEE ADDENDUM FOR MANUFACTURER LOCATIONS
68781 (Party Site)
Applicant: VOLEX (ASIA) PTE LTD
(337951-004) 35 TAMPINES ST 92
SINGAPORE 528880 SINGAPORE
This Follow-Up Service Procedure authorizes the above Manufacturer(s) to use the marking
specified by UL LLC, or any authorized licensee of UL LLC, including the UL Contracting
Party, only on products when constructed, tested and found to be in compliance with the
requirements of this Follow-Up Service Procedure and in accordance with the terms of the
applicable service agreement with UL Contracting Party and any applicable Service Terms. The
UL Contracting Party for Follow-Up Services is listed on addendum to this Follow-Up Service
Procedure ("UL Contracting Party"). UL Contracting Party and UL LLC are referred to jointly
herein as "UL."
UL further defines responsibilities, duties and requirements for both Manufacturers and UL
representatives in the document titled, "UL Mark Surveillance Requirements" that can be
located at the following web-site: http://www.ul.com/fus and in the document titled "UL and
Subscriber Responsibilities" that can be located at the following website:
http://www.ul.com/responsibilities. Manufacturers without Internet access may obtain the
current version of these documents from their local UL customer service representative or UL
field representative. For assistance, or to obtain a paper copy of these documents or the
applicable Service Terms, please contact UL's Customer Service at
http://www.ul.com/global/eng/pages/corporate/contactus, select a location and enter your
request, or call the number listed for that location.
The Applicant and the specified Manufacturer(s) in this Follow-Up Service Procedure must
agree to receive Follow-Up Services from UL Contracting Party. If your applicable agreement
is a Global Services Agreement ("GSA") with an effective date of January 1, 2012 or later
and this Follow-Up Service Procedure is issued on or after that effective date, the
Applicant and the specified Manufacturer(s) will be bound to a Service Agreement for Follow-
Up Services upon the earliest by any Subscriber of use of the prescribed UL Mark, acceptance
of the factory inspection, or payment of the Follow-Up Service fees which will incorporate
such GSA, this Follow-Up Service Procedure and the Follow-Up Service Terms which can be
accessed by clicking here: http://www.ul.com/contracts/Terms-After-12-31-2011. In all other
events, Follow-Up Services will be governed by and incorporate the terms of your applicable
service agreement and this Follow-Up Service Procedure.
File E62405SP Vol 3 Auth. Page 2 Issued: 2000-01-05
Revised: 2012-03-06
It is the responsibility of the Manufacturer to make sure that only the products meeting the
aforementioned requirements bear the authorized Marks of UL LLC, or any authorized licensee
of UL LLC.
This Follow-Up Service Procedure contains information for the use of the above
Manufacturer(s) and representatives of UL and is not to be used for any other purpose. It is
provided to the Manufacturer with the understanding that it will be returned upon request
and is not to be copied in whole or in part.
This Follow-Up Service Procedure, and any subsequent revisions, is the property of UL and is
not transferable. This Follow-Up Service Procedure contains confidential information for use
only by the above named Manufacturer(s) and representatives of UL and is not to be used for
any other purpose. It is provided to the Subscribers with the understanding that it is not
to be copied, either wholly or in part unless specifically allowed, and that it will be
returned to UL, upon request.
Capitalized terms used but not defined herein have the meanings set forth in the GSA and the
applicable Service Terms or any other applicable UL service agreement.
UL shall not incur any obligation or liability for any loss, expense or damages, including
incidental, consequential or punitive damages arising out of or in connection with the use
or reliance upon this Follow-Up Service Procedure to anyone other than the above
Manufacturer(s) as provided in the agreement between UL LLC or an authorized licensee of UL
LLC, including UL Contracting Party, and the Manufacturer(s).
UL LLC has signed below solely in its capacity as the accredited entity to indicate that
this Follow-Up Service Procedure is in compliance with the accreditation requirements.
William R. Carney
Director
North American Certification Program
File E62405SP Vol 3 Addendum To Page 1 Issued: 2000-01-05
Authorization Page Revised: 2012-03-06
LOCATION
433003 (Party Site)
(106395-001) VOLEX CABLE ASSEMBLY (SHENZHEN) CO LTD
VOLEX BLDG
1173 SHENHUI RD
BAO'AN, HENGGANG
SHENZHEN
GUANGDONG 518115 CHINA
Factory ID: SM OR HG
UL Contracting Party for above site is: UL AG
31812 (Party Site)
(221809-001) P T VOLEX INDONESIA
KAWASAN INDUSTRI
SEKUPANG
BATAM RIAU
. INDONESIA
Factory ID: B
UL Contracting Party for above site is: UL AG
67739 (Party Site)
(342882-001) VOLEX CABLE ASSEMBLY (VIETNAM) CO LTD
D-5B THANG LONG INDUSTRIAL PARK
DONG AHH DISTRICT
HANOI VIET NAM
Factory ID: VH
UL Contracting Party for above site is: UL AG
171879 (Party Site)
(788163-001) VOLEX INTERCONNECT (INDIA) PVT LTD
22-1A 1ST ST
KHAZURA GARDEN
NEELANGARAI
CHENNAI TN 600041 INDIA
Factory ID: VC
UL Contracting Party for above site is: UL India Private Limited
File E62405SP Vol 3 Addendum To Page 2 Issued: 2000-01-05
Authorization Page Revised: 2012-03-06
LOCATION
196799 (Party Site)
(918517-001) VOLEX CABLE ASSEMBLY (ZHONGSHAN) CO
LTD
ZHONGSHAN TORCH HI TECH IND DEV ZONE
2 SINTA N ST
ZHONGSHAN
GUANGDONG 528437 CHINA
Factory ID: SM1 OR SMI
UL Contracting Party for above site is: UL AG
File E62405SP Vol. 3 Index Page 1 Issued: 2000-01-05
Revised: 2003-07-23
ATTACHMENT PLUG CAPS:
NEMA CONFIGURATION
Belden
Models Config. Cord AWG A / V Sec. Fig. CUL Issued
AEC-P19 1-15 18,17/2 10,12/125 1 1 NO 02-02-90
AEC-P19CH 1-15 18,17/2 10,12/125 1 1 NO 02-02-90
AEC-20 1-15 18,16,14/2 10,13,15/125 1 2 NO 12-23-76
AEC-20P 1-15 18,16,14/2 10,13,15/125 1 2 NO 12-23-76
AEC-21 1-15 18,16,14/2 10,13,15/125 1 3 NO 02-02-90
AEC-21P 1-15 18,16,14/2 10,13,15/125 1 3 NO 02-02-90
AEC-22 1-15 18,16,14/2 10,13,15/125 1 4 NO 12-23-76
AEC-22CH 1-15 18,16,14/2 10,13,15/125 1 4 NO 12-23-76
AEC-22R-4 1-15 18,16,14/2 10,13,15/125 1 4 NO 12-23-76
AEC-22PR1 1-15 18,16,14/2 10,13,15/125 1 4 NO 12-23-76
AEC-22PR2 1-15 18,16,14/2 10,13,15/125 1 4 NO 12-23-76
AEC-22PR3 1-15 18,16,14/2 10,13,15/125 1 4 NO 12-23-76
AEC-23 1-15 18,16,14/2 10,13,15/125 1 5 NO 12-23-76
AEC-23P 1-15 18,16,14/2 10,13,15/125 1 5 NO 12-23-76
AEC-26 2-20 14,12 18,20/250 1 6 NO 02-20-87
AEC-27, -27P 1-15 18,16,14 10,13,15/125 1 7 NO 10-17-86
AEC-28 1-15 18,16,14/2 10,13,15/125 1 8 NO 03-22-76
AEC-29 1-15 18,16,14/2 10,13,15/125 1 9 NO 03-22-76
AEC-30 5-15 18,16,14 10,13,15/125 1 10 NO 09-19-75
AEC-30CH 5-15 18,16,14 10,13,15/125 1 10 NO 09-19-75
AEC-31 5-15 18,16,14,12 10,13,15,15/125 1 11 NO 09-19-75
AEC-32 6-15 18,16,14 10,13,15/250 1 12 NO 09-19-75
AEC-33 7-15 18,16,14,12 10,13,15,15/277 1 12A NO 09-19-75
AEC-34 6-20 18,16,14,12 10,13,15,20/125 1 -- NO 03-26-76
AEC-35 5-20 18,16,14,12 10,13,15,20/250 1 12B NO 03-29-76
AEC-36 5-15 14,12 15,15/125 1 13 NO 07-25-88
AEC-38 5-15 18,16,14 10,13,15/125 1 10 NO 09-19-75
AEC-38CH 5-15 18,16,14 10,13,15/125 1 10 NO 09-19-75
AEC-40-NB 5-15 18,16,14,12 10,13,15,15/125 1 14 NO 03-22-76
AEC-40-S 5-15 18,16,14,12 10,13,15,15/125 1 14 NO 03-22-76
AEC-41-N 6-15 18,16,14,12 10,13,15,15/250 1 14 NO 03-22-76
AEC-42-SFP 7-15 18,16,14,12 10,13,15,15/277 1 14 NO 03-22-76
AEC-43-N 5-20 18,16,14,12 10,13,15,20/125 1 14 NO 03-22-76
AEC-44-E 6-20 18,16,14,12 10,13,15,20/250 1 14 NO 03-22-76
AEC-45 5-15 18,16,14,12 10,13,15,15/125 1 15 NO 03-22-76
*AEC-50WB 5-15 18,16,14,12 10/125 1 16 NO 03-25-98
*AEC-50W 5-15 18,16,14,12 10/125 1 16 NO 03-25-98
*AEC-50NB 5-15 18,16,14,12 10/125 1 16 NO 03-25-98
*AEC-50N 5-15 18,16,14,12 10/125 1 16 NO 03-25-98
*AEC-50-1WB 1-15 18,16,14,12 13/125 1 16 NO 03-25-98
*AEC-50-1W 1-15 18,16,14,12 13/125 1 16 NO 03-25-98
*AEC-50-1NB 1-15 18,16,14,12 13/125 1 16 NO 03-25-98
*AEC-50-1N 1-15 18,16,14,12 13/125 1 16 NO 03-25-98
*AEC-50-1SB 5-15 18,16,14,12 10/125 1 16 NO 03-25-98
*AEC-50-1S 5-15 18,16,14,12 10/125 1 16 NO 03-25-98
*AEC-50-1EB 5-15 18,16,14,12 10/125 1 16 NO 03-25-98
*AEC-50-1E 5-15 18,16,14,12 10/125 1 16 NO 03-25-98
File E62405SP Vol. 3 Index Page 2 Issued: 2000-01-05
Revised: 2008-10-22
ATTACHMENT PLUG CAPS:
NEMA CONFIGURATION
Belden
Models Config. Cord AWG A / V Sec. Fig. CUL Issued
AEC-60(H) 5-15 18,16,14,12 10,13,15,15/125 1 17 YES 05-14-85
AEC-61(H) 6-15 18,16,14,12 10,13,15,15/250 1 17 YES 05-14-85
AEC-62(H) 5-20 18,16,14,12 10,13,15,20/125 1 17 YES 05-14-85
AEC-63(H) 6-20 18,16,14,12 10,13,15,20/250 1 17 YES 05-14-85
AP2-1 1-15 18,16,14/2 10,13,15/125 1 18 NO 04-01-86
AP2-1P 1-15 18,16,14/2 10,13,15/125 1 19 NO 05-08-86
AP2-2 1-15 14/2 13/125 1 20 NO 04-04-86
AP3-1 5-15 18,16/3 10,13/125 1 21 NO 04-02-86
AP3-1BT 5-15 18,16 10,13/125 1 22 NO 04-02-86
AP3-2 5-15 18,16 10,13/125 1 23 NO 04-02-86
AP3-3 5-15 18,16 10,13/125 1 24 NO 04-02-86
AP3-4 5-20 16,14,12 13,15,20/125 1 25 NO 04-03-86
AP3-5 5-15 18,16 10,13/125 1 29 NO 04-02-86
AP3-6 5-15 16,14,12 13,15,15/125 1 26 NO 04-03-86
AP3-7 6-15 16,14,12 13,15,15/250 1 27 NO 04-03-86
AP3-8 6-20 16,14,12 13,15,20/125 1 28 NO 04-03-86
BI-5204 5-15 18 10/125 1 30 NO 04-05-88
CH12975 5-15 4250AWM 0.4/125 1 31 NO 08-20-93
CX-11 5-15 18,16 10,13/125 1 32 NO 11-26-84
CX-91AN 5-15 18,16,14 10,13,15/125 1 33 NO 11-26-84
CX-91BN 5-15 18,16,14 10,13,15/125 1 33 NO 11-26-84
CX-91C 5-15 18,16,14 10,13,15/125 1 33 NO 11-26-84
CX-91DN 5-15 18,16,14 10,13,15/125 1 33 NO 11-26-84
CX-91E 5-15 18,16,14 10,13,15/125 1 33 NO 11-26-84
CX-91FN 5-15 18,16,14 10,13,15/125 1 33 NO 11-26-84
CX-91S 5-15 18,16,14 10,13,15/125 1 33 NO 11-26-84
CX-92 5-15 18,16,14 10,13,15/125 1 34 NO 11-26-84
CX-94 5-15 18 10/125 1 35 NO 11-26-84
CX-130 1-15 18,16/2 10,13/125 1 36 NO 11-23-84
CX-140 5-15 18,16,14 10,13,15/125 1 37 NO 11-26-84
CX-170-A 1-15 18,16/2 10,13/125 1 38 NO 11-30-84
CX-170NN 1-15 18,16/2 10,13/125 1 38 NO 11-30-84
CX-290 1-15 18,16 10,13/125 1 39 NO 11-30-84
CX-391 6-15 18,16,14,12 10,13,15,15/250 1 40 NO 12-04-84
CX-391-S 6-15 18,16,14,12 10,13,15,15/250 1 40 NO 12-04-84
CX-392 5-20 18,16,14,12 10,13,15,15/125 1 40 NO 12-04-84
CX-393 6-20 18,16,14,12 10,13,15,15/250 1 40 NO 12-04-84
*CX-394S 7-20 14,12 15,20/277 1 41 NO 12-04-84
*CX-394N 7-20 14,12 15,20/277 1 41 NO 12-04-84
CX-395 5-15 18,16,14,12 10,13,15,15/125 1 42 NO 01-25-95
CX-396 5-15 18,16,14,12 10,13,15,15/125 1 42 NO 01-25-95
CX-397 6-15 18,16,14,12 10,13,15,15/250 1 42 NO 01-25-95
CX-399 7-15 18,16,14,12 10,13,15,15/277 1 42 NO 01-25-95
CX-485 6-30 12,10 15,15/250 1 43 NO 12-05-84
CX-490 6-50 12,10,8 15,15,15/125 1 44 NO 11-27-84
CX-495 6-50 12,10,8 25,30,40/125,250 1 -- NO 11-27-84
DR3 10-30 10 30/250 1 45 NO 11-22-84
File E62405SP Vol. 3 Index Page 3 Issued: 2000-01-05
Revised: 2009-04-24
ATTACHMENT PLUG CAPS:
NEMA CONFIGURATION
Belden Models Config. Cord AWG A / V Sec. Fig. CUL Issued ECC-102 1-15 18,16/2 10,13/125 1 47 NO 11-23-84
ECC-103 1-15 18,16/2 10,13/125 1 47 NO 11-23-84 KM2P 5-15 18,16 10,13/125 1 48 NO 11-27-79 KM-2L3 6-15 18,16 10,13/250 1 49 NO 11-27-79
*
* * KM5D 10-30 10 30/125,250 1 51 NO 08-26-82 PL1030P 10-30 10/3 30/125,250 1 - NO PL1050P 10-50 8/2,10/1 40/125,250
6/2,8/1 50/125, 250 1 - NO PL1430P 10-30 10/4 30/125,250 1 - NO PL1450P 14-50 8/2,10/2 40/125,250
6/2,8/2 50/125, 250 1 - NO KM5E 14-30 10 30/125,250 1 51 NO 08-26-82 KM5F 7-30 12,10 25,30/277 1 50 NO 10-27-81
KM-8 1-15 18,16/2 10,13/125 1 52 NO 05-23-80 KM-8A 1-15 18,16/2 10,13/125 1 52 NO 05-23-80 KM-9 6-20 18,16,14,12 10,13,15, 20/250 1 53 NO 11-27-79
KM-9A 5-20 18,16,14,12 10,13,15, 20/250 1 53 NO 11-27-79
KM-11 5-15 18,16 10,13/125 1 54 NO 02-26-80 PH-22 1-15 16 13/125 1 55 NO 06-27-66
PH-43 5-15 16,14 13,15/125 1 56 NO 06-27-66 PH-44 6-15 18,16,14 10,13,15/250 1 57 NO 06-27-66 PH-44B 1-15 18,16,14 10,13,15/125 1 57 NO 06-27-66
PHC-44C 1-15 18,16,14 10,13,15/125 1 57 NO 06-27-66 PHC-44D 1-15 18,16,14 10,13,15/125 1 57 NO 06-27-66 PH-50 6-15 16,14 13,15/125 1 58 NO 06-27-66
PHF133-SN 1-15 27,20,18,16 2,2,10,13/125 1 59 NO 06-27-66 PH-173 5-15 18,16,14,12 10,13,15,15/125 1 60 NO 06-27-66 PH-173A 5-15 18,16,14,12 10,13,15,15/125 1 60 NO 06-27-66
PH-185 5-15 18,16,14 10,13,15/125 1 61 NO 06-27-66 PH-185F 5-15 18,16,14 10,13,15/125 1 61 NO 06-27-66 PHF-190 10-20 27,20 2,2.5/250 1 62 NO 06-27-66
PH-290A 5-15 18,16,14/3 10,13,15/125 1 63 NO 06-27-66
PH-290B 5-15 18,16,14/3 10,13,15/125 1 63 NO 06-27-66 PH-290D 5-15 18,16,14/3 10,13,15/125 1 63 NO
PH-290G 5-15 18,16,14/3 10,14,15/125 1 63 NO PH-290M 5-15 18,16,14/3 10,13,15/125 1 63 NO 06-27-66 PH-290N 5-15 18,16,14/3 10,13,15/125 1 63 NO 06-27-66
PH-290-O 5-15 18,17,16,14/3 10,10,13,15/125 1 63 NO PH-290P 5-15 18,16,14/3 10,13,15/125 1 63 NO 06-27-66 PH-290J 5-15 18,16,14 10,13,15/125 1 64 NO 06-27-66
PH-304 5-20 12 20/125 1 66 NO 06-27-66 PH-306 6-20 12 20/250 1 66 NO 06-27-66 PH-305 6-15 18,16,14 10,13,15/250 1 65 NO 06-27-66
PH-309 5-15 18,16,14 10,13,15/125 1 67 NO 06-27-66 PHC-309A 5-15 18,16,14 10,13,15/125 1 67 NO 06-27-66 PH-312A 6-30 10 30/250 1 68 NO 05-19-66
PH-312B 6-30 10 30/250 1 69 NO 05-19-66 PH-313 6-50 6 50/250 1 70 NO 06-27-66
File E62405SP Vol. 3 Index Page 4 Issued: 2000-01-05
Revised: 2007-05-21
ATTACHMENT PLUG CAPS:
NEMA CONFIGURATION
Belden Models Config. Cord AWG A / V Sec. Fig. CUL Issued PH-313B 6-50 6 50-250 1 70 NO 06-27-66
PH-347A 5-20 18,16,14,12 10,13,15,20/125 1 71 NO 06-27-66 PH-347B 6-20 18,16,14,12 10,13,15,20/250 1 71 NO 06-27-66 PH-347C 6-15 18,16,14,12 10,13,15,15/250 1 71 NO 06-27-66
PH-347D 5-15 18,16,14 10,13,15/125 1 71 NO 03-28-73 PH-347G 6-15 18,16,14 10,13,15/250 1 71 NO 03-28-73
PH-347F 1-15 18,16,14 10,13,15/125 1 71 NO 03-28-73
PH-615 14-30 10 30/125 1 72 NO 06-07-73 PH-616 14-50 6 50/250 1 73 NO 06-07-73 PH-700 5-15 14 15/125 1 74 NO 10-25-79
PH727 5-15 18,16 10,13/125 1 75 NO 06-27-99 *PH-960 L5-15 18 10/125 1 76 YES 10-09-92 PH-961 L5-20 16,14,12 13,15,20/125 1 125 YES
PL-3001 1-15 18 10/125 1 124 Yes 06-27-66 PL-3009 1-15 18,16,14 10,13,15/125 1 126 NO 10-27-04 PL-3010 5-15 18,16,14 10,13,15/125 1 127 NO 10-27-04
RA3 10-20 6 20/250 1 77 NO 11-22-84 R1 5-15 18,16,14 10,13,15/125 1 78 NO 11-26-80 R2 5-15 18,16,14 10,13,15/125 1 79 NO 11-26-80
R3-1 5-15 18,16,14 10,13,15/125 1 80 NO 11-26-80
R3-2 5-15 18,16,14 10,13,15/125 1 80 NO 11-26-80 R3-3 5-15 16,14 13,15/125 1 80 NO 11-26-80
R3 5-15 18,16,14 10,13,15/125 1 80 NO 11-26-80 R4 5-15 18,16,14 10,13,15/125 1 81 NO 11-26-80 R5 5-15 18,16 10,13/125 1 81 NO 11-26-80
S1 5-15 18,16,14 10,13,15/125 1 82 NO 11-26-80 S2-2 1-15 18,16,14 10,13,15/125 1 83 NO 11-26-80 S3 1-15 18,16,14 10,13,15/125 1 84 NO 11-26-80
S-289-S 1-15 27,18,17,16,14 2,10,12,13,15/125 1 88 NO 06-27-66 S-289-S-GT 1-15 27,18,17,16,14 2,10,12,13,15/125 1 88 NO 06-27-66 S-289-S-K 1-15 27,18,17,16,14 2,10,12,13,15/125 1 88 NO 06-27-66
S-289-S-L 1-15 27,18,17,16,14 2,10,12,13,15/125 1 88 NO 06-27-66 S-289-S-LT 1-15 27,18,17,16,14 2,10,12,13,15/125 1 88 NO 06-27-66 S-289-S-O 1-15 27,18,17,16,14 2,10,12,13,15/125 1 88 NO 06-27-66
S-289-S-T 1-15 27,18,17,16,14 2,10,12,13,15/125 1 88 NO 06-27-66
S-289-SN 1-15 27,18,17,16,14 2,10,12,13,15/125 1 88 NO 06-27-66 S-289-SN-G 1-15 27,18,17,16,14 2,10,12,13,15/125 1 88 NO 06-27-66
S-289-SN-GT 1-15 27,18,17,16,14 2,10,12,13,15/125 1 88 NO 06-27-66 S-289-SN-K 1-15 18,16,14 10,15,15/125 1 88 NO 06-27-66 S-289-SN-L 1-15 18,16,14 10,15,15/125 1 88 NO 06-27-66
S-289-SN-LT 1-15 27,18,17,16,14 2,10,12,13,15/125 1 88 NO 06-27-66 S-289-SN-O 1-15 27,18,17,16,14 2,10,12,13,15/125 1 88 NO 06-27-66 S-289-SN-T 1-15 27,18,17,16,14 2,10,12,13,15/125 1 88 NO 06-27-66
S-289-T 1-15 27,18,17,16,14 2,10,12,13,15/125 1 88 NO 06-27-66 SPH-290K 5-15 18,16,14 10,13,15/125 1 64 NO 06-27-66 SPH-727 5-15 - - 1 75 NO 06-27-66
133-SP 1-15 27,20,18,16 2,2,10,13/125 1 85 NO 05-23-80 133-S 1-15 18,16 10,13/125 1 85 NO 05-23-80 173,-A 5-15 18,16,14/3 10,13,15/125 1 86 NO 05-19-66
185,-F 5-15 18,16,14/3 10,13,15/125 1 -- NO 05-19-66
289-D, -E 1-15 27,18,17,16,14 2,10,12,13,15/125 1 87 NO 05-03-66 289-F, -G 1-15 27,18,17,16,14 2,10,12,13,15/125 1 87 NO 05-03-66
File E62405SP Vol. 3 Index Page 5 Issued: 2000-01-05
Revised: 2007-05-21
ATTACHMENT PLUG CAPS:
NEMA CONFIGURATION
Belden
Models Config. Cord AWG A / V Sec. Fig. CUL Issued 289-J 1-15 27,18,17,16,14 2,10,12,13,15/125 1 87 NO 05-03-66 289-Q 1-15 27,18,17,16,14 2,10,12,13,15/125 1 88 NO 06-27-66
289-R 1-15 27,18,17,16,14 2,10,12,13,15/125 1 88 NO 06-27-66 289-S 1-15 27,18,17,16,14 2,10,12,13,15/125 1 88 NO 06-27-66 289-S-G 1-15 27,18,17,16,14 2,10,12,13,15/125 1 88 NO 06-27-66
289-S-K 1-15 27,18,17,16,14 2,10,12,13,15/125 1 88 NO 06-27-66 289-S-L 1-15 27,18,17,16,14 2,10,12,13,15/125 1 88 NO 06-27-66 289-S-O 1-15 27,18,17,16,14 2,10,12,13,15/125 1 88 NO 06-27-66
289-SN 1-15 27,18,17,16,14 2,10,12,13,15/125 1 88 NO 06-27-66 289-SN-G 1-15 27,18,17,16,14 2,10,12,13,15/125 1 88 NO 06-27-66 289-SN-K 1-15 18,16,14 10,15,15/125 1 88 NO 06-27-66
289-SN-L 1-15 18,16,14 10,15,15/125 1 88 NO 06-27-66 289-SN-O 1-15 27,18,17,16,14 2,10,12,13,15/125 1 88 NO 06-27-66 304 5-20 12 20/125 1 89 NO 06-27-66
310 5-15 14,12 15,15/125 1 90 NO 06-27-66 310A 5-15 14,12 15,15/125 1 90 NO 06-27-66 333RP 5-15 18,16 10,13/125 1 -- NO 11-27-79
366-S 5-15 18,16,14 10,13,15/125 1 91 NO 02-26-80 366-SE 5-15 18,16,14 10,13,15/125 1 91 NO 02-26-80 366-SP 5-15 18,16,14 10,13,15/125 1 91 NO 02-26-80
366-SPE 5-15 18,16,14 10,13,15/125 1 91 NO 02-26-80 377B 1-15 18,16 10,13/125 1 92 NO 01-06-97 610A 1-15 18,16,14 10,13,15/125 1 93 NO 07-10-96
610A-S 1-15 18,16,14 10,13,15/125 1 93 NO 07-10-96 644, -A 1-15 18, 16 10/125 1 94 NO 01-06-97 661 1-15 18, 16 10/125 1 96 NO 01-06-97
661A 1-15 18, 16 10/125 1 96 NO 01-06-97 648 5-30 10 30/125 1 95 NO 08-16-74 668A 5-20 18,16,14,12 10,13,15,20/125 1 71A NO 06-27-66
668B 6-20 18,16,14,12 10,13,15,20/250 1 71A NO 06-27-66 668C 6-15 18,16,14,12 10,13,15,15/250 1 71A NO 06-27-66 668D 5-15 18,16,14 10,13,15/125 1 71A NO 03-28-73
668G 6-15 18,16,14 10,13,15/250 1 71A NO 03-28-73 668F 1-15 18,16,14 10,13,15/125 1 71A NO 03-28-73 697 1-15 18 10/125 1 97 NO 02-28-89
772 1-15 18,17 10,12/125 1 98 NO 07-22-83 772A 1-15 18,17 10,12/125 1 98 NO 07-22-83 772B 1-15 17 12/125 1 98 NO 07-22-83
772S 1-15 18,17 10,12/125 1 98 NO 07-22-83 772SA 1-15 18,17 10,12/125 1 98 NO 07-22-83 813(h) 5-15 18,16,14 10,13,15/125 1 -- NO 01-21-87
814(h) 5-15 18,16,14 10,13,15/125 1 100 NO 01-21-87 814A(h) 5-15 18,16,14 10,13,15/125 1 100 NO 01-21-87 814B(h) 5-15 18,16,14 10,13,15/125 1 100 NO 01-21-87
814C(h) 5-15 18,16,14 10,13,15/125 1 100 NO 01-21-87 814D(h) 5-15 18,16,14 10,13,15/125 1 100 NO 01-21-87 815 1-15 18,16 6,6/125 1 101 NO 02-18-87
816 5-15 18 6/125 1 -- NO 02-18-87 838 1-15 18,16 10,13/125 1 102 NO 06-30-89 838B 1-15 18,17 10,12/125 1 102 NO 06-30-89
File E62405SP Vol. 3 Index Page 6 Issued: 2000-01-05
Revised: 2007-05-21
ATTACHMENT PLUG CAPS:
NEMA CONFIGURATION
Belden
Models Config. Cord AWG A / V Sec. Fig. CUL Issued
847 5-15 18 10/125 1 103 NO 08-08-88
860 1-15 18,17,16,14 10,12,13,15/125 1 104 NO 03-23-92
860-HT 1-15 18,17,16,14 10,12,13,15/125 1 104 NO 03-23-92
860-T 1-15 18,17,16,14 10,12,13,15/125 1 104 NO 03-23-92
862 5-15 18,16,14/3 10,13,15/125 1 63 NO 06-27-66
1362A 1-15 18, 16, 14/3 10,13,15/125 1 - NO
879B 1-15 14,12 15,15/125 1 105 NO 03-27-73
882 5-15 18,17,16,14 10,12,13,15/125 1 -- NO 03-23-92
882-T 5-15 18,17,16,14 10,12,13,15/125 1 -- NO 03-23-92
894B(EMI) 5-15 18,16,14 7,7,7/125 1 106 NO 08-22-91
926 1-15 18,16,14 10,13,15/125 1 107 YES 08-23-96
926C 1-15 18,16,14 10,13,15/125 1 -- YES 01-05-00
952 5-15 18,16,14 10,13,15/125 1 -- YES 08-23-96
953 5-15 18,16,14 10,13,15/125 1 -- YES 08-23-96
1533 1-15 18,16,14 10,13,15/125 1 109 NO 12-17-84
1533A 1-15 18,16,14 10,13,15/125 1 109 NO 12-17-84
1533C 1-15 18,16,14 10,13,15/125 1 109 NO 12-17-84
1541 Locking 16,14 13,15/125 1 110 NO 10-09-92
5197 5-15 18,16 10,13/125 1 112 NO 03-22-73
5205 5-15 18,16 10,13/125 1 112 NO 03-22-73
5210 5-15 18,16 10,13/125 1 112 NO 03-22-73
5942 5-15 18 10/125 1 111 NO 03-22-73
5943 5-15 18,16 10,13/125 1 112 NO 03-22-73
5944 5-15 18,16,14 10,13,15/125 1 113 NO 11-26-84
5945 1-15 18,16/14 10,13,15/125 1 113 NO 11-26-84
5982 5-15 18,16,14 10,13,15/125 1 114 NO 02-16-82
5983 5-15 18,16,14 10,13,15/125 1 115 NO 02-16-82
PL1030P 10-30 10/3 30/125,250 1
IEC CONFIGURATION
Models Config. Cord AWG A / V Sec. Fig. CUL Issued
AEC-150 C14 18,16,14 10,13,15/125 1 116 NO 06-28-89
388 C14 18 10/125 1 117 NO 03-02-70
388A C14 18 10/125 1 117 NO 03-02-70
388B C14 18 10/125 1 117 NO 03-02-70
388C C14 18 10/125 1 117 NO 03-02-70
388D C14 18 10/125 1 117 NO 03-02-70
388E C14 18 10/125 1 117 NO 03-02-70
388F C14 18 10/125 1 117 NO 03-02-70
388J C14 18 10/125 1 117 NO 03-02-70
388L C14 18 10/125 1 117 NO 03-02-70
388K C14 18 10/125 1 118 NO 03-02-70
File E62405SP Vol. 3 Index *Page 7 Issued: 01-05-00
New: 08-31-01
ATTACHMENT PLUG CAPS:
NON-STANDARD CONFIGURATION
Models Config. Cord AWG A / V Sec. Fig. CUL Issued
PH-100 -- 18 10/125 1 119 NO 06-27-66
PH-235 -- 14 16/250 1 120/121 NO 04-01-86
PH-235A -- 14 16/250 1 120/121 NO 04-01-86
PH-235B -- 14 16/250 1 120/121 NO 04-01-86
PH-235C -- 14 16/250 1 120/121 NO 04-01-86
PH-235D -- 14 16/250 1 120/121 NO 04-01-86
PH-235E -- 14 16/250 1 120/121 NO 04-01-86
PH-235F -- 14 16/250 1 120/121 NO 04-01-86
PH-235G -- 14 16/250 1 120/121 NO 04-01-86
PH-633 -- 18 2.5/250 1 122 NO 10-20-75
916 -- 18 10 1 123 NO 08-20-90
916A -- 18 10 1 123 NO 08-20-90
File E62405SP Vol. 3 Index Page 8 Issued: 2000-01-05
Revised: 2013-08-09
CORD CONNECTOR BODIES:
NEMA CONFIGURATION
Models Config. Cord AWG A / V Sec. Fig. CUL Issued
AEC-202 1-15 18,16,14 10,13,15/125 2 1 NO 2000-05-02
AEC-210 5-15 18,16,14 10,13,15/125 2 2 NO 2000-05-02
AEC-212 5-15 16,14 13,15/125 2 2 NO 2000-05-02
AEC-231 1-15 16,14 13,15/125 2 3 NO 2000-05-02
AEC-232 6-15 16,14 13,15/250 2 3 NO 2000-05-02
AEC-234 6-20 16,14 13,18/250 2 3 NO 2000-05-02
AEC-235 5-20 16,14 13,18/125 2 3 NO 2000-05-02
F1-3 5-15 16,14 13,15/125 2 9 NO 1984-09-18
FL-3 5-15 16,14 13,15/125 2 10 NO 1988-04-13
PH-32 5-15 16,14 13,15/125 2 11 NO 1966-06-28
PH-32D 1-15 16,14 13,15/125 2 -- NO 1966-06-28
PH-108B 5-15 16,14 13,15/125 2 -- NO 1966-06-28
PH-108A 5-15 16,14 13,15/125 2 11 NO 1966-06-28
645 1-15 16 13/125 2 27 NO 1966-06-28
645A 1-15 16 13/125 2 27 NO 1966-06-28
5987 5-15 16 13/125 2 31 NO 1989-12-27
IEC CONFIGURATION
Models Config. Cord AWG A / V Sec. Fig. CUL Issued
AEC-250 C13 18,16,14 10,13,15/250 2 4 NO 2000-05-02
AEC-250A,-B C13 18,16,14 10,13,15/250 2 4 NO 2000-05-02
AEC-251 C17 18,16,14 10,13,15/250 2 4 NO 2000-05-02
AEC-255L,-R C13 18,16,14 10,13,15/250 2 4 NO 2000-05-02
AEC-255LA, C13 18,16,14 10,13,15/250 2 4 NO 2000-05-02
-LB,-RA,-RB
AEC-256L,-R C17 18,16,14 10,13,15/250 2 4 NO 2000-05-02
CX-300 C13 18 10/125 2 8 NO 1984-12-06
PH-913 C7 18 13/125 2 16 NO 1969-12-15
386,-C,-E,-F,-
H,-J,-L
C13 18,16 10,13/250 2 22 NO 1970-03-02
386A C13 18,16,14 10,13,15/125
or 250
2 22 YES 1970-03-02
386AL C13 18,16,14 10,13,15/125
or 250
2 32 YES 2000-05-02
386B C13 18,16 10,13/250 2 22 NO 1970-03-02
386P, -POD C13 18,16,14 10,13,15/125 2 23 NO 1970-03-02
386Q C13 14 15/125 2 24 NO 1970-03-02
390C C13 18,16,14 10,13,15/125 2 25 NO 1970-03-02
390D C17 18,16 10,13/250 2 22 NO 1970-03-02
390E C13 18,16,14 10,13,15/125 2 25 NO 1970-03-02
391,-A, -B, C13 18,16,14 10,13,15/125 2 25 NO 1970-03-02
-C, -E
726 C13 18,16,14 10,13,15/125 2 28 NO 1970-03-02
904 C13 18,16,14 10,13,15/125 2 25 NO 1970-03-02
910, 911 C13 18,16,14 10,13,15/250 2 25 NO 1970-03-02
846 C13 18 10/125 2 29 NO 1988-07-25
877 C13 18 10/125 2 30 NO 1990-08-20
File E62405SP Vol. 3 Index Page 9 Issued: 2000-01-05
Revised: 2008-08-05
NON-STANDARD CONFIGURATION
Models Config. Cord AWG A / V Sec. Fig. CUL Issued
AEC-380 2 cond. 18,16 7/125 2 5 NO 2000-05-02
AEC-381 3 cond. 18,16 7/125 2 5 NO 2000-05-02
CX-150 2 cond. 18 7/125 2 6 NO 1984-11-29
CX-160AK 2 cond. 18 7/125 2 7 NO 1984-11-28
PH-94 2 cond. 18,16 13/125 2 12 NO 1966-06-28
PH-98 2 cond. 18 7/125 2 13 NO 1966-06-28
PH-103 2 cond. 18,16 13/125 2 12 NO 1966-06-28
PH-104 2 cond. 18 10/125 2 21 NO 2000-05-02
PH-109 2 cond. 18,16 2/125 2 12 NO 1966-06-28
*PH-163 3 cond. 18 10/125 2 21 NO 2000-05-02
PH-164 2 cond. 18 10/125 2 21 NO 2000-05-02
PH-322H 2 cond. 27 0.12/125 2 14 NO 1973-05-02
PH-326 3 cond. 18,16 7/125 2 15 NO 1966-06-28
SFE-2 2 cond. 18 0.4/125 2 17 NO 1987-01-07
SPH-222 2 cond. 18 10/125 2 21 NO 2000-05-02
SPH-243 3 cond. 18 7/125 2 18 NO 1966-06-28
SPH-602 2 cond. 18 10/125 2 21 NO 2000-05-02
SPH-622B 3 cond. 18 7/125 2 19 NO 1973-02-28
SPH-637 4 cond. 18 7/125 2 20 NO 1966-06-28
SPHC-750 2 cond. 27 0.12/125 2 21 NO 1967-10-24
638A 3 cond. 18 7/125 2 26 NO 1966-06-28
CURRENT TAP:
NEMA CONFIGURATION
Cat. No. Config. Cord AWG Electrical A/V Sec. Fig. C-UL
728, -APOD 18,16 10,13/125 3 1,2 No
745 18,16 10,13/125 3 - No
AEC-50 Series 18 10/125 3 3 No
US615RPAB,
US615RPAT
6-15 18,16,14 10,13,15/250 3 4,5 Yes
US615RPAL,
US615RPAR
6-15 18,16,14 10,13,15/250 3 6,7 Yes
US515RPAB,
US515RPAT
5-15 18,16,14 10,13,15/125 3 8,9 Yes
US515RPAL,
US515RPAR
5-15 18,16,14 10,13,15/125 3 10,11 Yes
File E62405SP Vol. 3 Index Page 10 Issued: 2000-01-05
Revised: 2003-03-05
REPLACES PAGE 10