Fibre Channel card Users Guide - Fujitsumanuals.ts.fujitsu.com/file/8792/C122-E012-19EN_.pdf · < Ex. > Emulex LPX000 Fibre Channel Storport Driver . 13 4. Click the "Driver"

PRIMEQUEST

Fibre Channel card Users Guide

2G Fibre Channel PCI-X card （MC-08FC11/ MC-08FC71） 4G Fibre Channel PCI-X card （MC-08FC31/ MC-08FC41） 4G Fibre Channel PCI-express card （MC-08FC51/ MC-08FC61） 8G Fibre Channel PCI-express card （MC-08FC81/ MC-08FC91）

MC IA Server Business Division

Copyright FUJITSU LIMITED 2008

1

C122－E012－19EN

2

Contents

1. Driver / TOOL / Firmware version..................................................................................4 2. The outline of this product .............................................................................................5 3. Specification ..................................................................................................................5 4. First setting by the EFI BIOS.........................................................................................7

4.1. Setting Topology ................................................................................................................. 7 4.2. Setting Link Speed............................................................................................................ 10 4.3. Changing the setting of opposed devices (Fibre Channel Switch / ETERNUS Disk Storage System) ........................................................................................................................................11

5. Installing ...................................................................................................................... 11 5.1. Red Hat Linux / SUSE Linux driver ...................................................................................11 5.2. Windows driver ..................................................................................................................11

Windows Server 2003...............................................................................................................11 5.2.1. Confirming the version level of the driver that now in use..........................................11 5.2.2. Installing the driver and tool ...................................................................................... 12 5.2.3. Confirming after Installing (Driver)............................................................................. 12 5.2.4. Confirming after Installing (HBAnyware Utility, LightPulse Utility/NT)........................ 12 Windows Server 2008.............................................................................................................. 12 5.2.5. Confirming the version level of the driver that now in use......................................... 12 5.2.6. Installing the driver and tool ...................................................................................... 13 5.2.7. Confirming after Installing (Driver)............................................................................. 13 5.2.8. Confirming after Installing (HBAnyware Utility).......................................................... 13

6. Uninnstalling................................................................................................................13 6.1. Red Hat Linux / SUSE Linux driver .................................................................................. 13 6.2. Windows driver ................................................................................................................. 14

Windows Server 2003.............................................................................................................. 14 6.2.1. Uninstalling the driver ................................................................................................ 14 6.2.2. Confirming after uninstalling ...................................................................................... 14 Windows Server 2008.............................................................................................................. 14 6.2.3. Uninstalling the driver ................................................................................................ 14 6.2.4. Confirming after uninstalling ...................................................................................... 15

7. Upgrade ......................................................................................................................15 7.1. Red Hat Linux / SUSE Linux driver .................................................................................. 15 7.2. Windows driver ................................................................................................................. 15

8. Update of EFI / Firmware ............................................................................................16 9. Instruction for proper use ............................................................................................16

9.1. Mounting condition ........................................................................................................... 16 9.2. Limitations when Fibre Channel card is exchanged. ........................................................ 16

3

9.3. Note EFI driver name ....................................................................................................... 16 9.4. Note when SAN configurations is changed (When EFI Driver before 3.11a4 is used.) .... 17 9.5. Setting driver parameter ................................................................................................... 18 9.6. Release Note for EFI Driver ............................................................................................. 21

4

1. Driver / TOOL / Firmware version Driver/TOOL/Firmware of following Version is in CD. [Driver / TOOL Version in Driver CD]

OS Kernel version Version

Linux [Emulex LightPulse Fibre Channel Driver] About a number for kernel and a version of a driver, confirm README in directory: "kernel version" which this manual is arranged.

Windows

Windows Server 2003 SP2

Windows Server 2008

【StorPort MiniPort Driver】=6.2.10.7 【HBAnyware】=4.0a32

-Caution- With the installation of a driver for

WS2003/WS2008, it is necessary to update Firmware/EFI Driver of FC card. Please inquire of Fujitsu service engineer about further information.

[EFI Driver/Firmware Version in Driver CD]

Firmware MC-08FC11/71 MC-08FC31 MC-08FC41 MC-08FC51 MC-08FC61 MC-08FC81 MC-08FC91

Shipment ver. 1.91a5 2.10a7 2.10a7 2.10a7 2.10a7 1.11a5

WS2003/2008 ver.

1.92a1 2.80a4 2.80a4 2.80a4 2.80a4 1.11a5

EFIDriver MC-08FC11/71 MC-08FC31 MC-08FC41 MC-08FC51 MC-08FC61 MC-08FC81 MC-08FC91

Shipment ver. 3.11x1 3.11x1 3.11x1 4.00a1

WS2003/2008 ver.

4.00a1 4.00a1 4.00a1 4.00a1

＊ As for Linux, use a shipment version. When MC08FC81/91 is used, the change of the following software/firmware is necessary.

PAL/SAL Firmware : 3.10 or later. PSA(PRIMEQUEST Server Agent) :

Linux is 1.17.2-1 or later. Windows 2003 is 1.17.1.13 or later. Windows2008 is 1.17.2.0 or later.

5

2. The outline of this product 1) By mounting Fibre Channel card with PCI slot, you can add 1 or 2 port for Fibre Channel

interface of 8 Gbps(800MB/s). 2) This card offers solutions for enterprise-class SAN(Storage Area Networks)

3. Specification (1) 2G Fibre Channel Card

Item Specification

Model Number MC-08FC11/ MC-08FC71

Host Bus Interface PCI-2.3 , PCI-X 1.0a

Standard/Transmission

method/Protocol FC-PI-2,FC-FS,FC-AL-2,FC-GS-4,FCP-2,RFC2625(IP over FC),

FC-PH,FC-PH-2,FC-PH-3,FC-PI,FC-AL,FC-FLA,FC-PLDA,FC-TAPE,FCP

Service class Class2, 3

Transmission media Multi-mode optical fibre cable (50/125μm MMF, Dual LC connector)

Multi-mode optical fibre cable (62.5/125μm MMF, Dual LC connector)

Data transfer rate MAX 200MB/s ( Synchronous transfer mode )

Connection distance MAX 300m (50/125μm) at 2Gbps

MAX 150m (62.5/125μm) at 2Gbps

Allotted number of ports 1 port

The number of connecting

devices

MAX 126 devices / 1 Loop

Form of connector Dual LC connector

6

(2) 4G Fibre Channel Card Item Specification

Model Number MC-08FC31 MC-08FC41 MC-08FC51 MC-08FC61

Host Bus Interface PCI-2.3, PCI-X 1.0a PCI-Express 1.0a


method/Protocol

FC-FS,FC-PH,FC-PI,FC-PI-2,

FCP,FCP-2,FC-AL,FC-PLDA,

FC-MI,FC-FLA,

RFC2625(IP over FC)

FC-FS,FC-PH-3,FC-PI-2,FC-TAPE,

FCP-2,FC-AL-2,FC-PLDA,FC-GS-4,

FC-FLA,RFC2625(IP over FC)





Connection distance MAX 150m(50/125μm) at 4Gbp

MAX 70m(62.5/125μm) at 4Gbps

Allotted number of ports 1 port 2 ports 1 port 2 ports


devices


Form of connector Dual LC connector

(3) 8G Fibre Channel Card

Item Specification

Model Number MC-08FC81 MC-08FC91

Host Bus Interface Fibre Channel PCI Express2.0


method/Protocol

FC-PI-4,FC-FS-2,FC-FS-2/AM1,FC-LS,AL-AL-2,FC-GS-6,

FC-FLA,FC-PLDA,FC-TAPE,FC-DA,FCP through FCP-4,

SBC-3,FC-SP,FC-HBA and SMI-S v1.1





Connection distance MAX 50m(50/125μm) at 8Gbp

MAX 21m(62.5/125μm) at 8Gbps

Allotted number of ports 1 port 2 port


devices


Form of connector SFP+short wave optical transce

iver connector x1

SFP+short wave optical transce

iver connector x2

4. First setting by the EFI BIOS

<Start EFI BIOS setup screen>

1. Enter to EFI Shell by selecting "EFI Shell [Built-in]" in EFI Boot Manager first screen. 2. Confirm the driver number of the target card by performing confirm command in EFI

Shell screen. Confirm command : “Shell>drivers –b”

3. Confirm the numerical value NN (DRV / here, it is 22) at the beginning of the "Emulex SCSI Pass Thru Driver" from the displayed screen.

4. Start EFI BIOS screen with the numerical value that has been confirmed in section 3. Start command : “Shell>drvcfg –s 22”

5. Emulex FC EFI-Bios Utility is started.

4.1. Setting Topology Set as follows to connection form (Fablic / FCAL) in EFI-Bios. * It is equipped with two Single FC cards and two Dual FC card in the following EFI-Bios Utility screen.

<Fablic >

EFI-Bios Utility first screen

7

T D

D Y C I

R P F A

V VERSION E G G #D #C DRIVER NAME IMAGE NAME

=== ======== = = = ===== ============================== ==============

022 00040011 B X X 6 1 Emulex SCSI Pass Thru Driver elxcli400a1

Select the target card that setting is changed 1) Select Setup Utility.

2) Select Configure HBA Parameters.

8

3) Select Topology Selection.

4) Select Point to Point.

9

<FCAL> The procedure that is selecting the target card that is changed setting is the same as

<Fablic> 1) - 3). 4) Select FCAL.

4.2. Setting Link Speed Set as follows to connecting Link Speed (2/4/8Gbps) in EFI-Bios.

Return to 4.1-3) screen by pushing Esc key in above screen and select "4. Force Link Speed".

The initial setting is "Auto negotiate – Default". Select Link speed to the using environment.

10

4.3. Changing the setting of opposed devices (Fibre Channel Switch / ETERNUS Disk Storage System)

The setting opposed Fibre Channel Switch and ETERNUS Disk Storage System is needed to setting Fibr Channel Card.

As for the detail, refer to ETERNUS Disk Storage System Settings / 2.1.1 Setting the To-server Connection Type (Setting the CA Parameters) of ETERNUS disk storage system Server Connection GUIDE (Fibre Channel).

5. Installing 5.1. Red Hat Linux / SUSE Linux driver

Confirm README in directory: "kernel version" which this manual is arranged.

5.2. Windows driver

OS InstallDriver Path

WS2003 SP2 DVD-ROM：¥Tools¥General¥Emulex¥APInstall.EXE

WS2008 DVD-ROM：¥Tools¥General¥Emulex¥APInstall.EXE

Windows Server 2003

5.2.1. Confirming the version level of the driver that now in use

1. Boot Windows Server 2003 and log on by the user with Administrator privileges. 2. Right-click the My Computer entry and click the Properties. 3. Click the Hardware tab of System properties and click the button, "Device Manager".

"Device Manager" is displayed. 4. Click the "+" of the SCSI and RAID controllers and existing FC adapters are

displayed. - It is displayed by either the following.( The display is different in each driver.)

Emulex LightPulse LPxxxxx, PCI Slotxxx, Storport Miniport Driver Emulex LightPulse LPxxxxx, Storport Miniport Driver

Emulex LightPulse HBA Storport Miniport Driver

11

● Please do not install, when current version is newer or same.

● Please install after ending all the applications. ● After installing, reboot the system so that the driver

which is applied becomes effective.

12

Double-click the above icon. 5. Click the "Driver" tab and confirm the version level of the driver now in use.

5.2.2. Installing the driver and tool

1. Double-click the following files in the Driver CD: “Tools＼General＼Emulex＼APInstall.exe”

The Setup Wizard begins. 2. Click the "Next" button. 3. Start Driver Installation Issue screen. 4. Click the "Next" button. 5. Start install. 6. When "HBAnyware UtilityManagement Mode" screen is displayed, select the "Strictly

Local Management" and click the "OK" button. 7. "Verify Installation" is finished in the Setup Wizard, click the "Next(N)" button. 8. The complete screen is displayed in the next screen, click the "Finish" button.

* After rebooting the system, the driver which is applied becomes effective.

5.2.3. Confirming after Installing (Driver)

Refer to Clause 5.2.1.

5.2.4. Confirming after Installing (HBAnyware Utility, LightPulse Utility/NT)

1. Click the “Start” button on the Taskbar. Confirm [Program](or [All programs]) →[Emulex] → [HBAnyware] is displayd.

2. Run HBAnyware. Click the “Help” and click the “About HBAnyware”. The window of HBAnyware About Box is displayed. Confirm the version level of HBAnyware.

Windows Server 2008

5.2.5. Confirming the version level of the driver that now in use

1. Boot Windows Server 2008 and log on by the user with Administrator privileges. 2. Click the "+" of Diagnostics in Server Manager and display "Device Manager" by

choosing it. 3. Click the "+" of “Storage controllers”, existing SCSI adapters are displayed.

Double-click the Emulex LPX000 Fibre Channel Storport Driver icon. < Ex. > Emulex LPX000 Fibre Channel Storport Driver

13

4. Click the "Driver" tab and confirm the version level of the driver now in use. < Ex. > version 5.1.30.208 / inbox driver)

5.2.6. Installing the driver and tool

1. Double-click the following files in the Driver CD: “Tools＼General＼Emulex＼APInstall.exe”

The Setup Wizard begins. 2. Click the "Next" button. 3. Start Driver Installation Issue screen. 4. Click the "Next" button. 5. Start install 6. When "Autopilot Installer Warning" screen is displayed, click the "OK" button. 7. "Verify Installation" is finished in the Setup Wizard, click the "Next(N)" button. 8. The complete screen is displayed in the next screen, click the "Finish" button.

* After rebooting the system, the driver which is applied becomes effective.

5.2.7. Confirming after Installing (Driver)

Refer to Clause 5.2.5.

5.2.8. Confirming after Installing (HBAnyware Utility)

1. Click the “Start” button on the Taskbar. Confirm [Program](or [All programs]) →[Emulex] → [HBAnyware], [HBAnyware] is displayd.

2. Run HBAnyware. Click the “Help” and click the “About HBAnyware”. The window of HBAnyware About Box is displayed. Confirm the version level of HBAnyware.

6. Uninnstalling

6.1. Red Hat Linux / SUSE Linux driver Confirm README in directory: "kernel version" which this manual is arranged.

14

6.2. Windows driver

Windows Server 2003

6.2.1. Uninstalling the driver

1. Click the "Start" button of the taskbar, and click the "Control panel" and "Addition and deletion of the program". The program being installed now is displayed.

2. Select the following programs and perform delete. Emulex Common SAN Management <Version> Emulex HBAnyware Utility <Version> Emulex Storport Miniport Driver Kit <Version>

Click these. 3. Click the “Change/Remove” button. 4. The Uninstall Wizard begins. Click the “Next” button. 5. The “Confirm Uninstall” are displayd, Click the “OK” button, Uninstall starts. 6. The completion of Uninstall Wizard is displayed. Click the "Finish" button.

6.2.2. Confirming after uninstalling

1. Click the "Start" button of the taskbar, and click the "Control panel" and "Addition and deletion of the program". The program being installed now is displayed.

2. Confirm the following programs are deleted. Emulex Common SAN Management <Version> Emulex HBAnyware Utility <Version> Emulex Storport Miniport Driver Kit <Version>

Windows Server 2008

6.2.3. Uninstalling the driver

1. Click the "Start" button of the taskbar and click the "Control panel"→"Programs and Features".The program being installed now is displayed.

2. Select the following programs and perform delete. Emulex Common SAN Management <Version> Emulex HBAnyware Utility <Version> Emulex Storport Miniport Driver Kit <Version>

Click these.

15

3. Right-click the target program and select "uninstallation and change (U)". 4. The Uninstall Wizard begins. Click the “Next” button. 5. The “Confirm Uninstall” are displayd, Click the “OK” button, Uninstall starts. 6. The completion of Uninstall Wizard is displayed. Click the "Finish" button.

6.2.4. Confirming after uninstalling

1. Click the "Start" button of the taskbar and click the "Control panel"→"Programs and Features".The program being installed now is displayed.

2. Confirm the following programs are deleted. Emulex Common SAN Management <Version> Emulex HBAnyware Utility <Version> Emulex Storport Miniport Driver Kit <Version>

7. Upgrade

7.1. Red Hat Linux / SUSE Linux driver

Confirm README in directory: "kernel version" which this manual is arranged.

7.2. Windows driver

Follow the procedure "5.2.2 Installing the driver and tool(Windows Server 2003)" or "5.2.6 Installing the driver and tool(Windows Server 2008)" to upgrade the FC card driver.

16

8. Update of EFI / Firmware With the installation of Windows Server 2003 SP2 and Windows Server 2008, the firm up of the FC card will be necessary. For Firmup detail, ask a certified service engineer.

9. Instruction for proper use

9.1. Mounting condition The mounting slot of PCI Card is assigned. For further information, ・See the chapter 2.3.5 Mounting conditions of PCI cards and

usable built-in I/Os in PRIMEQUEST 580A/540A/580/540/480/440 SYSTEM DESIGN GUIDE (C122-B001-EN)

・See the chapter 2.3.4 Mounting conditions of PCI cards and usable built-in I/Os in PRIMEQUEST 520A/520/420 SYSTEM DESIGN GUIDE (C122-B009-EN)

9.2. Limitations when Fibre Channel card is exchanged. <OS: Windows Server 2003 DTC , Windows Server 2003 EE , Windows Server 2008> -When you change Fibre Channel card used for boot path to other

Fibre Channel card (other part# card), OS reinstall will be necessary. -No need to reinstall OS for the change between the same part# products. -No need to reinstall OS when Fibre Channel card is used for data path.

9.3. Note EFI driver name When it boots from SAN storage device and updates Firmware built-in PCI

card, it should perform "drivers" command with EFI shell mode and confirm EFI Driver which displayed "Emulex SCSI Pass Thru Driver".

When it uses EFI Driver version 3.11x1, it is displayed as follows by IMAGE NAME column, but there is no problem in movement.

Also, when plural version coexists and they are displayed, please use the "VERSION" column that numerical value is big, so it is a new publication.

EFI Shell> drivers T D D Y C I R P F A V VERSION E G G #D #C DRIVER NAME IMAGE NAME === ======== = = = == === =================================== ================= 022 00031016 ? X X - - Emulex SCSI Pass Thru Driver Elxcli310a6 023 00031131 B X X 2 1 Emulex SCSI Pass Thru Driver PciRom Seg=000000

EFIDriver version 3.11x1

9.4. Note when SAN configurations is changed (When EFI Driver before 3.11a4 is used.) < Occurrence phenomenon >

・"EFI Internal Error2" is displayed in BOOT in SANBOOT environment by a screen, and there is the case that the phenomenon that a system is reset.

< Occurrence condition > ・After it was done SANBOOT setting (WWPN of Boot Target setting), when FC switch and

setting of the RAID side are changed, and it cannot be seen Boot Volume, it occurs. < Avoidance >

(1) In the state that EFI system stands up (EFI prompt is displayed ( “ EFI Shell> “)), change FC switch or setting of the RAID side, carry out Scan Target by all means, and set Boot Target again.

(2) If FC switch or setting of the RAID side is changed in the state that EFI system does not stand up, in the state that the fiber cable which is connected to pertinent FC card is pulled, start EFI system (EFI prompt is displayed ( “ EFI Shell> “)), connect fiber cable again, carry out Scan Target by all means, and set Boot Target again.

17

9.5. Setting driver parameter Driver palameter which is necessary when Fujitsu ETERNUS 3000/4000/8000 Disk Storage System and FC card be connected is described below.

* As for the maximum speed of the using Fibre Channel card, confirm it in a product manual and Emulex corporation website.

Emulex corporation website : http://www.emulex.com < Linux OS >

Confirm README in directory: "kernel version" which this manual is arranged. < Windows OS >

Set the following driver parameters.

1 Start HBAnyware Utility. Click the [Start] button, [Program](or [All programs]) - [Emulex] - [HBAnyware], HBAnyware Utility is started. 2 Select the port every the pertience FC card and click the "Driver Parameters".

18

When it is the same setting in all Fibre Channel cards, select locar server and select the "Driver Parameters".

19

3 Confirm the set point (Value) of each Adapter Parameter. Confirm and revise the set point that is mentioned in the following lists. Revise it (Value) in "Modify Adapter Parameters" by Adapter Parameter.

- Windows Server 2003 SP1/SP2, 2008

Value Maximum data transfer

rate Topology QueueDepth Queue

Target

LinkSpeed

8Gbps Fibre Channel

card

4Gbps Fibre Channel

card

2Gbps Fibre Channel

card

0 (FCAL)

1(Fablic)

ETERNUS8000,4000 is 254.

ETERNUS2000 calculates (*2).

1 (*1)

*1: Link Speed

Fablic

(Fibre Channel Switch connection)

FCAL

ET8000/ET4000

Fibre Channel card

transfer rate

8Gbps

4Gbps

2Gbps

1Gbps

FC-CA

(4G)

FC-CA

(8G)

ET2000

8Gbps 8 4 2 - 4 8 4

4Gbps 4 4 2 1 4 4 4

2Gbps 2 2 2 1 2 2 2

*2: In ETERNUS2000, set the value that is calculated in the following expression. The value = 40 / the number of Fibre Channel port that is connected a CA port (The decimal

point cuts it off). When the value is smaller than 8, set it in 8.

Caution : Change only the parameters that is explained here.

< Explanation of parameter >

- “Topology” It sets a connection form PRIMEQUEST and ETERNUS Disk Storage System.

- “QueueDepth” It sets the number of the command cues.

- “QueueTarget” It sets the number of the command cues for LUN or a target.

- “LinkSpeed” It sets Link Speed.

4 Click the "Apply" button after revising the value. As for the parameter displayed with red in Adapter Parameter, the value is not changed. Click the "Aplly" button.

5 When the every several cards are changed the value, repeat the above perform 1 ~ 4. < Notes when LinkSpeed is set > When LinkSpeed parameter setting of a PCI card is made a mistake in , it may result in OSBoot

is impossible in SANBoot environment. < Ex. >

The case of LinkSpeed parameter of 4G Fibre Channel Card (MC-08FC31/41/51/61) is set "LinkSpeed=4" and FC-AL connection/ fabric connection is connected to other party of CA corresponding to 2Gbps.

20

6 Finish HBAnyware Utility by selecting “Exit” in “File” after completing the all setting. The values that are changed become effective after rebooting the server. 7 Reboot the server after revising the values. The setting that is changed become effective after rebooting the server.

9.6. Release Note for EFI Driver It may result in there is no Dual Channel card notation for pertinence EFIDriver Release Note in "PRIMEQUEST Firmware CD(C122-E018)", but when there is the description of the same kind of Single Channel card, it may have applicability to it.

< Ex.>

When there is the description of following Single Channel(Lp11000) in Release Note, the application of Dual Channel(Lp11002) is possible.

21

BE311X1.PRG Lp11000 EFIBoot version 3.11X1

Documents

Fibre Channel card Users Guide - Fujitsumanuals.ts.fujitsu.com/file/8792/C122-E012-19EN_.pdf · < Ex. > Emulex LPX000 Fibre Channel Storport Driver . 13 4. Click the "Driver"