Fiberglass Surface Prep

Fiberglass Surface Prep YMA601 is a low VOC cleaner that emulsifies and lifts mold release agentsand other contamination from the surface of fiberglass gelcoats so that it can be removed withclean, fresh water. Fiberglass Surface Prep cleans the surface and provides a key for Fiberglass No Sand Primer YPA200 or InterProtect® 2000E. The removal of surface contamination isextremely important to prevent delamination of subsequent coats of primers and paint. FiberglassSurface Prep can also be used on previously painted or varnished surfaces when preparing torepaint.

COMPATIBILITYFiberglass Surface Prep can be used on Fiberglass Gelcoat (Polyester or Vinylester) and Epoxyprimed surfaces prior to the application of Fiberglass No-Sand Primer YPA200 or InterProtect2000E.

PRODUCT DATAn Product code and color: YMA601 Pink

n Coverage: N/A

n Surfaces: Fiberglass gelcoat (polyester or vinylester) and epoxy primed surfaces

n Application: Maroon 3M™ Scotch-Brite™ pad

n Application temperature: 50°F (10°C) to 95ºF (35ºC)

n VOC: 2.71 lbs/gal (325 grams/liter) as supplied

n Case pack: 6 Quarts per case, 2 Gallons per case

Our World is Water

Product & Code Description

Fiberglass No Sand Primer YPA200 Single part primer

InterProtect® Gray 2000E/2001E Epoxy barrier for blister protection, prevention and priming

InterProtect® White 2002E/2001E Epoxy barrier for blister protection, prevention and priming

ASSOCIATED PRODUCTS

Our World is Water

FEB 201

1

PREPARATIONStir or shake contents thoroughly before use.

Bare Fiberglass

Apply Fiberglass Surface Prep YMA601 to a maroon 3M™ Scotch-Brite™ pad, then scrub the surfaceto be cleaned using moderate pressure. Flush the surface with fresh water or wipe off with a clean,wet cloth ensuring that no traces of Fiberglass Surface Prep YMA601 remain. Changing clothsfrequently, repeat until all contamination is removed.

Before application of primer it is very important that all contamination has been removed. To becertain the contamination has been removed, run water over the surface. If the water beads up orseparates, wipe again with Fiberglass Surface Prep YMA601, rinse and allow to dry.

As soon as the surface is dry it is ready to apply Fiberglass No Sand Primer YPA200 or InterProtect®

2000E. If more than 4 hours pass without overcoating wipe with a clean wet cloth and allow to dry.

HINTFor large areas, pour YMA601 into a paint tray and roller apply. Apply one section at a time, then scrubusing a maroon 3M™ Scotch-Brite™ pad and water to remove.

DISCLAIMERThe information given in this sheet is not intended to be exhaustive. Any person using this product without first making further enquiries as to the suitability of the product for the intended purpose does so attheir own risk and we can accept no responsibility for the performance of the product or for any loss or damage (other than death or personal injury resulting from negligence) arising out of such use. The information contained in this sheet is liable to modification from time to time in the light of experience and our policy of continuous development.Please refer to your local representative or www.yachtpaint.com for further information.

RECOMMENDED APPLICATION SYSTEMS

GENERAL DIRECTIONS

International Paint LLC 2270 Morris Avenue, Union, NJ 07083 Tel: (908) 686-1300 Toll Free Technical Help: 1-800-468-7589 Fax: (908) 686-85451 ®, Interlux®, the AkzoNobel logo and all product names mentioned in this publication are trademarks of, or licensed to, AkzoNobel. © Akzo Nobel N.V. 2011.3M™ and Scotch-Brite™ are trademarks of 3M.