IMPREZA/CROSSTREKKit Part No. H461SFL000

INTERIOR FOOTWELL ILLUMINATION

FI11671 Issue: 1 Date: 24/08/20169

© Lumen Australia 2016

Page 1 of

Parts Supplied

Safety Notes

General Notes

Tools Required

Kit Part No: H461SFL000

•

•

•

•

•

•

Read through the fitting instructions before installation of the accessory. Install the accessory following the fitting instructions. Failure to do so may cause damage to the vehicle or the accessory.

Ensure all recyclable discarded vehicle accessory components and packaging are recycled following local recycle regulations.

It is always recommend that this accessory is fitted by a qualified automotive technician.

Safely store and protect any removed vehicle components.

Ensure all bare metal surface are protected using automotive bare metal primer and touch-up paint, or suitable automotive rust inhibitor.

Remove all metals swarf and dust from all vehicle surface if surface is used for accessory installation.

•

•

Check that all work practices comply with safety standards.

Please wear appropriate clothing and use safety equipment.

Light x2 Harness x1 Cable Tie x7 Foam Tape - Large x1

1 2 3 4

Phillips Head Screwdriver Trim Removal Tool

Page 2 of

Torque WrenchRatchet8mm & 10mm Socket

Foam Tape - Small x2

5

Bracket x1

6

Flat Washer x2 CAP Nut x2

7 8

FI11671 Issue: 1 Date: 24/08/20169

© Lumen Australia 2016

Kit Part No: H461SFL000

FI11671 Issue: 1 Date: 24/08/20169

© Lumen Australia 2016

Harness

Light

BB

A

Page 3 of

Step 1

Step 2

Step 3

Kit Part No: H461SFL000

• Disconnect the negative battery terminal.

• Remove the RH Side Dash Cover .

• Remove the glovebox plunger

• Remove the glovebox

• Remove Ornament Panel .

.

.

1

2

3

Page 4 of

Ÿ Remove the LH side dash cover .Ÿ Remove the phillips head screw .Ÿ Remove the LH lower dash cover and unplug all

switches.

1

2

3

1

2

1

2

3

3

FI11671 Issue: 1 Date: 24/08/20169

© Lumen Australia 2016

Kit Part No: H461SFL000

Step 4

Step 5

Step 6

Page 5 of

Ÿ Remove the seven phillips head screws and remove the glove box inner frame .

1

2

Ÿ Assemble the LED housing to the bracket (LH).Ÿ Plug in the short side of the harness to the LED .

1 2

3 1

Ÿ Remove rubber boots from airbag mounting studs. 1

21

2

2

1

1

3

1

11

11

1

FI11671 Issue: 1 Date: 24/08/20169

© Lumen Australia 2016

Kit Part No: H461SFL000

Step 7

Step 8

Step 9

Page 6 of

Ÿ Attach bracket to LH knee airbag mounting studs using 8mm cap nut (Torque is 6.9 ± 0.9Nm, 61.07 - 7.97inlbs) and flat washers .

1

2

3

Ÿ Route the harness through the center console.Ÿ Secure the harness on the LH side with the two wire

ties to factory ignition harness and one wire tie to the OE harness at the white tape marks of Illumination Harness.

1

1

2 3

33

2 2

1

2

1

2

3

Ÿ Continue routing the harness through the center console.

1

DRIVER SIDE PASSENGER SIDE

11

FI11671 Issue: 1 Date: 24/08/20169

© Lumen Australia 2016

Kit Part No: H461SFL000

Step 10

Page 7 of

Step 11

Step 12

Ÿ Secure harness on RH side with four wire ties to various tie points at the white tape marks of Illumination Harness.

1 2

Ÿ Replace the glove box inner frame and secure using the seven previously removed phillips head screws .

1

2

1 22

22

Ÿ Plug in long side of harness to LED . Ÿ Mount LED to glove box Inner frame .

1 2

2 3

1

2

2

1

3

1

2

2

2

2

1

FI11671 Issue: 1 Date: 24/08/20169

© Lumen Australia 2016

Step 13

Kit Part No: H461SFL000

Step 14

2

1

Ÿ Reinstall the LH Lower Dash Cover and LH Side Dash Cover .

1

2

Step 15

Ÿ Connect power plug to factory Illumination Control harness .

Ÿ Wrap the connectors in the large foam .Ÿ Wrap factory Illumination Control harness in the

small foam .

1

2

3

2

4

1

2

Ÿ Replace the ornament panel Ÿ .Ÿ Replace the glove box .Ÿ Replace the RH side dash cover .

Replace the glovebox plunger

1

2

3

3

2

1

13

2

4

2

Page 8 of FI11671 Issue: 1 Date: 24/08/20169

© Lumen Australia 2016

Kit Part No: H461SFL000

FI11671 Issue: 1 Date: 24/08/20169

© Lumen Australia 2016

Step 16

E. & O.E. This document is copyright and must not be used except as permitted below or under the Copyright Act 1968. You may reproduce and publish this document in whole or in part for your or your organisation's own.

Personal or internal compliance, educational or non-commercial purposes. You must not alter or amend this document in any way. You must not reproduce or publish this document for commercial gain without the prior written consent of the copyright owner.

• Reconnect the negative battery terminal .

• Test Footwell Illumination in a dark area by turning the park lamps on and checking both footwells for correct illumination.

(Torque is 7.5 Nm, 66.38inlbs)

Wiring Diagram

ILL +ILL -

Vehicle

ILL CONT SW

Vehicle

2 1 2 1

LEDLED

Accessory - Footwell Illumination

Page 9 of