GB

Valid for serial no. 606--xxx--xxxx0461 066 001 GB 090310

FeedMech 4804/FeedControl

Instruction manual

-- 2 --TOCe

Rights reserved to alter specifications without notice.

1 DIRECTIVE 3. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2 SAFETY 3. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3 INTRODUCTION 5. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

3.1 Equipment 5. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

4 TECHNICAL DATA 5. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5 INSTALLATION 6. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

5.1 Terminating resistor 6. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5.2 Example of a robotic welding system 7. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

6 OPERATION 7. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6.1 Connections 8. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6.2 Gas flow guard (if installed) 10. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6.3 Wire feed pressure 10. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6.4 Replacing and inserting wire 11. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6.5 Changing feed rollers 11. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

7 MAINTENANCE 11. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7.1 Inspection and cleaning 11. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

8 ORDERING SPARE PARTS 12. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .DIAGRAM 14. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .ORDERING NUMBER 16. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .WEAR PARTS 18. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .ACCESSORIES 20. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

-- 3 --bm49d1ea

1 DIRECTIVEDECLARATION OF CONFORMITY

ESAB AB, Welding Equipment, SE--695 81 Laxå, Sweden, gives its unreserved guarantee that unitFeedMech 4804 / FeedControl from serial number 606 are constructed and tested in compliance withthe standard EN 60974--1/--5 and EN 60974--10 (Class A) in accordance with the requirements of di-rective (2006/95EC) and (2004/108/EEC).--------------------------------------------------------------------------------------------------------------------------------------

Kent EimbrodtGlobal DirectorEquipment and Automation

Laxå 2008--06--12

2 SAFETYUsers of ESAB welding equipment have the ultimate responsibility for ensuring that anyone whoworks on or near the equipment observes all the relevant safety precautions. Safety precautionsmust meet the requirements that apply to this type of welding equipment. The following recommen-dations should be observed in addition to the standard regulations that apply to the workplace.

All work must be carried out by trained personnel well--acquainted with the operation of the weldingequipment. Incorrect operation of the equipment may lead to hazardous situations which can resultin injury to the operator and damage to the equipment.

1. Anyone who uses the welding equipment must be familiar with:S its operationS location of emergency stopsS its functionS relevant safety precautionsS welding

2. The operator must ensure that:S no unauthorized person is stationed within the working area of the equipment when it is

started up.S no--one is unprotected when the arc is struck

3. The workplace must:S be suitable for the purposeS be free from drafts

4. Personal safety equipmentS Always wear recommended personal safety equipment, such as safety glasses, flame--proof

clothing, safety gloves.S Do not wear loose--fitting items, such as scarves, bracelets, rings, etc., which could become

trapped or cause burns.

5. General precautionsS Make sure the return cable is connected securely.S Work on high voltage equipment may only be carried out by a qualified electrician.S Appropriate fire extinquishing equipment must be clearly marked and close at hand.S Lubrication and maintenance must not be carried out on the equipment during operation.

GB

-- 4 --bm49d1ea

WARNING

Read and understand the instruction manual before installing or operating.

Arc welding and cutting can be injurious to yourself and others. Take precausions when welding.Ask for your employer’s safety practices which should be based on manufacturers’ hazard data.

ELECTRIC SHOCK - Can killS Install and earth the welding unit in accordance with applicable standards.S Do not touch live electrical parts or electrodes with bare skin, wet gloves or wet clothing.S Insulate yourself from earth and the workpiece.S Ensure your working stance is safe.FUMES AND GASES - Can be dangerous to healthS Keep your head out of the fumes.S Use ventilation, extraction at the arc, or both, to take fumes and gases away from your breathing zone

and the general area.ARC RAYS - Can injure eyes and burn skin.S Protect your eyes and body. Use the correct welding screen and filter lens and wear protective

clothing.S Protect bystanders with suitable screens or curtains.FIRE HAZARDS Sparks (spatter) can cause fire. Make sure therefore that there are no inflammable materials nearby.NOISE - Excessive noise can damage hearingS Protect your ears. Use earmuffs or other hearing protection.S Warn bystanders of the risk.MALFUNCTION - Call for expert assistance in the event of malfunction.

PROTECT YOURSELF AND OTHERS!

CAUTION!This product is solely intended for arc welding.

CAUTION!Class A equipment is not intended for use in residential locations wherethe electrical power is provided by the public low--voltage supplysystem. There may be potential difficulties in ensuring electromagneticcompatibility of class A equipment in those locations, due to conductedas well as radiated disturbances.

Do not dispose of electrical equipment together with normal waste!In observance of European Directive 2002/96/EC on Waste Electrical and ElectronicEquipment and its implementation in accordance with national law, electrical equipmentthat has reached the end of its life must be collected separately and returned to anenvironmentally compatible recycling facility. As the owner of the equipment, you shouldget information on approved collection systems from our local representative.By applying this European Directive you will improve the environment and humanhealth!

GB

-- 5 --bm49d1ea

CAUTION!Read and understand the instruction manual beforeinstalling or operating.

ESAB can provide you with all necessary welding protection and accessories.

3 INTRODUCTION

The wire feed unit consist of a drive unit (FeedMech 4804) and a separate electronicunit (FeedControl).

The wire feed unit is intended for MIG/MAG welding along with robotic equipment.

NOTE!

The wire feed unit utilizes the robot’s safety system to obtain maximum interference protection.

ESAB’s accessories for the product can be found on page 20.

3.1 Equipment

The wire feed unit is supplied with an instruction manual, and the drive unit with asticker with recommended wear parts.

4 TECHNICAL DATAFeedMech 4804 FeedControl

Power supply 42 V 50--60 Hz 42 V 50--60 Hz

Power requirement 378 VA 378 VA

Motor current Imax 9.0 A 9.0 A

Settings dataWire feed speed 0.8 -- 25.0 m/min

Gun connection EURO

Wire dimensionFeSsAlCored wire

0.6--2.4 mm0.6--2.4 mm1.0--1.6 mm0.8--2.4 mm

Operating temperature --10 to + 40˚C --10 to + 40˚C

Weight 9.7 kg 4.9 kg

Dimensions (l x b x h) 383 x 161 x 287 mm 330 x 118 x 320 mm

Shielding gasmax pressure

Gases for MIG/MAG--welding5 Bar

Gases for MIG/MAG--welding5 Bar

GB

-- 6 --bm49d1ea

FeedControlFeedMech 4804

Maximum permissible load at60% intermittens100% intermittens

500 A280 A

500 A280 A

Enclosure class IP2X IP2X

Duty cycleThe duty cycle refers to the time as a percentage of a ten--minute period that you can weld at a cer-tain load without overloading. The duty cycle is valid for 40˚C.

The duty cycle is valid for 40˚C.

Enclosure classThe IP code indicates the enclosure class, i. e. the degree of protection against penetration by solidobjects or water. Apparatus marked IP2X are intended for indoor use.

5 INSTALLATION

The installation must be executed by a professional.

Note!Mains supply requirementsHigh power equipment may, due to the primary current drawn from the mains supply, influence thepower quality of the grid. Therefore connection restrictions or requirements regarding themaximum permissible mains impedance or the required minimum supply capacity at the interfacepoint to the public grid may apply for some types of equipment (see technical data). In this case itis the responsibility of the installer or user of the equipment to ensure, by consultation with thedistrubution network operator if necessary, that the equipment may be connected.

WARNING!When welding in an environment with increased electrical danger, only powersources intended for this environment may be used. These power sources aremarked with the symbol

5.1 Terminating resistor

The ends of the CAN bus must be fitted with terminatingresistors to avoid communication interference.

The terminating resistor is delivered with the powersource.

One end of the CAN bus is at the control panel (U8),which has an integral terminating resistor.The other end is at the FeedControl and must befitted with the terminating resistor, as shown on theright.

GB

-- 7 --bm49d1ea

5.2 Example of a robotic welding system

6 OPERATIONGeneral safety regulations for the handling of the equipment can be found onpage 3. Read through before you start using the equipment!

WARNING!Rotating parts can cause injury, take great care.

GB

-- 8 --bm49d1ea

6.1 Connections

FeedMech 4804

1 Switch for gas purging 9 Connection to drive unit, 4 poles

2 Switch for reversed wire feed 10 Connection to drive unit, 8 poles

3 Switch for cold wire feed 11 Connection for coolant from power source(cooling unit), BLUE

4 Connection for coolant to welding gun,BLUE

12 Connection for coolant to power source(cooling unit), RED

5 Connection for coolant from welding gun,RED

13 Inlet connection for spatter removal air

6 Outlet connection for spatter removal air 14 Connection for shielding gas in

7 Connection for signals to/from robotwelding gun

15 Connection for welding current fromelectronic unit (OKC)

8 Connection for welding gun 16 Rating plate

GB

-- 9 --bm49d1ea

FeedControl1 White indicating lamp – Power supply ON 9 Rating plate

2 Connection from electronic unit to driveunit

10 Connection for terminating resistor orforwarding to next wire feed unit

3 Connection from electronic unit to driveunit

11 Connection for control cable from powersource

4 Outlet connection for spatter removal air 12 Connection for shielding gas, in

5 Connection for coolant to welding gun,BLUE

13 Inlet connection for spatter removal air

6 Connection for welding current from driveunit (OKC)

14 Connection for coolant from power source(cooling unit), BLUE

7 Connection for coolant from welding gun,RED

15 Connection for welding current from powersource (OKC)

8 Connection for shielding gas, out 16 Connection for coolant to power source(cooling unit), RED

Symbol and function explanations

Gas purging

Used to measure the gas flow or to flush the gas hoses to clean them of any air andmoisture before commencing welding. Gas purging is carried out with the voltageand wire feed switched off.

GB

-- 10 --bm49d1ea

Reversed wire feed

Used to reverse the wire, for example when replacing the wire bobbin.

Inching

Used when wire is to be fed without switching on the welding voltage.

Inlet spatter removal air

Outlet spatter removal air

Used for spray--cleaning the contact tip on the welding gun.

Shielding gas in

Shielding gas out

6.2 Gas flow guard (if installed)

The gas flow monitor interrupts the ongoing welding process if the gas flow dropsbelow 3.5 l/min. When this occurs, an error message is displayed via the control unit.

6.3 Wire feed pressure

Start by making sure that the wire moves smoothly through the wire guide. Thenset the pressure of the wire feeder’s pressure rollers. It is important that thepressure is not too great.

Fig 1 Fig 2

To check that the feed pressure is set correctly, you can feed out the wire againstan insulated object, e.g. a piece of wood.

When you hold the gun approx. 5 mm from the piece of wood (fig. 1) the feedrollers should slip.

If you hold the gun approx. 50 mm from the piece of wood, the wire should befed out and bend (fig. 2).

GB

-- 11 --bm49d1ea

6.4 Replacing and inserting wireS Open the side panel.S Disconnect the pressure sensor by folding it backwards, the pressure rollers

slide up.S Straighten out the new wire 10--20 cm. File away burrs and sharp edges from the

end of the wire before inserting it into the wire feed unit.S Make sure that the wire goes properly into the feed

roller’s track and into the outflow nozzle or wire guide.S Secure the pressure sensor.S Close the side panel.

6.5 Changing feed rollersS Push down the pressure device (1) and pull it

towards you and upwards.S Pull out the bogey (2).S Remove the socket--head bolts (3) on the

intermediate nozzle and remove it.S Loosen the bolt holding the outlet nozzle (4)

and push the nozzle back.S Remove the socket--head bolt (5) in the centreS Slacken the two socket--head bolts (6) by half a turn.S Pull out the feed rollers (7).Reassemble in the reverse order.

Selecting the correct groove in thefeed rollersPlace no, one or two carrier washersbetween the outer washer and the feedrollers. NB: Replace the entire bogeywhen changing the pressure rollers (8).

7 MAINTENANCERegular maintenance is important for safe, reliable operation.

CAUTION!All guarantee undertakings from the supplier cease to apply if the customer himselfattempts any work in the product during the guarantee period in order to rectify any faults.

7.1 Inspection and cleaning

Wire feed unit

Check regularly that the wire feed unit is not clogged with dirt.

S Cleaning and replacement of the wire feed unit mechanism’s worn parts shouldtake place at regular intervals in order to achieve trouble--free wire feed. Notethat if pre--tensioning is set too hard, this can result in abnormal wear on thepressure roller, feed roller and wire guide.

GB

-- 12 --bm49d1ea

Welding gun

S Cleaning and replacement of the welding gun’s wear parts should take place atregular intervals in order to achieve trouble--free wire feed. Blow the wire guideclean regularly and clean the contact tip.

8 ORDERING SPARE PARTS

FeedMech4804 / FeedControl is designed and tested in accordance with the internatio-nal and European standards IEC/EN 60974--1, 60974--5 and 60974--10. It is the obliga-tion of the service unit which has carried out the service or repair work to make surethat the product still conforms to the said standard.

Spare parts may be ordered through your nearest ESAB dealer, see the last page ofthis publication.

GB

-- 13 --p

Diagram

-- 14 --bm49e

FeedControl & FeedMech 4804

-- 15 --bm49e

FeedMech 4804/FeedControl

Edition 090310

Ordering number

-- 16 --bm40o

Ordering no. Denomination Type Note

0461 070 8800461 070 8810461 080 8800459 839 007

Drive unitDrive unitFeed boxSpare parts list

Aristot Feed Mech 4804Aristot Feed Mech 4804Aristot Feed Control

23 pole12 pole

The spare parts list is available on the Internet at www.esab.com

-- 17 --p

FeedMech 4804/FeedControl

R0461 066/E090310/P22

Wear parts

-- 18 --bm49whk1

HD = Heavy Duty

Item Ordering no. Denomination Wire type Wire dimensions

HK1 0469 837 8800469 837 8810469 837 882

Outlet nozzleOutlet nozzleOutlet nozzle

Fe, Ss & coredAlFe, Ss & cored

Ø 2.0 mm steel for 0.6--1.6 mmØ 2.0 mm plastic for 1.0--1.6 mmØ 3.4 mm steel for 2.0--2.4 mm

Item Ordering no. Denomination Wire type Wire Ømm

Groove 1 Groove 2 Groove 3 Groovetyp

Roller /Bogeymark-ings

HK2 0366 966 880 Feed Roller Fe, Ss & cored 0.6--1.2 0.6--0.8 0.9--1.0 1.2 V 10366 966 881 Feed Roller Fe, Ss & cored 1.4--1.6 1.4--1.6 2.0 2.4 V 20366 966 889 Feed Roller Fe, Ss & cored 1.2 .045” / 1.2 .045” / 1.2 .045” / 1.2 V .045 / 70366 966 900 Feed Roller Fe, Ss & cored 0.9--1.6 0.9--1.0 1.2 1.4--1.6 V 60366 966 882 Feed Roller Cored 1.2--2.0 1.2 1.4--1.6 2.0 V--Knurled 30366 966 883 Feed Roller Cored 2.4 2.4 not used not used V--Knurled 40366 966 885 Feed Roller Al 1.2 1.2 1.2 1.2 U U20366 966 899 Feed Roller Al 1.0--1.6 1.0 1.2 1.6 U U4

Item Ordering no. Denomination Notes

HK3 0156 707 001 Distance washer

HK4 0156 707 002 Adjustment spacer

HK5 Screw M5x20

HK6 Screw M5x16

Item Ordering no. Denomination Wire type Wire dimensions Groovetyp

Roller /Bogey

markings

HK7 0366 902 880 Bogey (HD) Fe, Ss & cored Ø 0.6 -- 1.2 mm V 10366 902 900 Bogey (HD) Fe, Ss & cored Ø 0.9 -- 1.6 mm V 60366 902 881 Bogey (HD) Fe, Ss & cored Ø 1.4 -- 2.4 mm V 30366 902 894 Bogey (HD) Fe, Ss & cored Ø 1.2 mm V .045 / 70366 902 882 Bogey (HD) Cored Ø 1.2 -- 2.0 mm V--Knurled 30366 902 883 Bogey (HD) Cored Ø 2.4 mm V--Knurled 40366 902 899 Bogey (HD) Al Ø 1.0 -- 1.6 mm U U40366 902 886 Bogey (HD) Al Ø 1.2 mm x 3 U --

Item Ordering no. Denomination Wire type Wire dimensions

HK8 0366 944 001 Washer

HK9 0156 603 0010156 603 0020332 322 0010332 322 002

Intermediate nozzleIntermediate nozzleIntermediate nozzleIntermediate nozzle

Fe, Ss & AlFe, Ss & AlCoredCored

Ø 2 mm plastic for 0.6--1.6 mmØ 4 mm plastic for 2.0--2.4 mmØ 2.4 mm copper for 1.2--2.0 mmØ 4 mm copper for 2.4 mm

Item Ordering no. Denomination Note

HK10 0215 702 708 Locking washer

HK11 Nut M10

HK12 0458 748 002 Insulating washer

HK13 0458 748 001 Insulating bushing

Item Ordering no. Denomination Wire type Wire dimensions

HK14 0156 602 0010156 602 0020332 318 0010332 318 002

Inlet nozzleInlet nozzleInlet nozzle (HD)Inlet nozzle (HD)

Fe, Ss, Al & CoredFe, Ss, Al & CoredFe, Ss & CoredFe, Ss & Cored

Ø 2 mm plastic for 0.6--1.6 mmØ 4 mm plastic for 2.0--2.4 mmØ 2.4 mm steel for 1.2--2.0 mmØ 4 mm steel for 2.4 mm

FeedMech 4804/FeedControl

R0461 066/E090310/P22-- 19 --bm49whk1

FeedMech 4804/FeedControl

R0461 066/E090310/P22

Accessories

-- 20 --bm49a

Quick connector MarathonPact . . . . . . . . . . . . F102 440 880

Adapterplate for mounting on the robot arm . . . . . 0461 038 880

1 Check valve . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2 Gas flow meter . . . . . . . . . . . . . . . . . . . . . . . . . .

0461 110 8800460 005 881

-- 21 --p

ESAB ABSE--695 81 LAXÅSWEDENPhone +46 584 81 000

www.esab.com

081016

ESAB subsidiaries and representative offices

EuropeAUSTRIAESAB Ges.m.b.HVienna--LiesingTel: +43 1 888 25 11Fax: +43 1 888 25 11 85

BELGIUMS.A. ESAB N.V.BrusselsTel: +32 2 745 11 00Fax: +32 2 745 11 28

THE CZECH REPUBLICESAB VAMBERK s.r.o.VamberkTel: +420 2 819 40 885Fax: +420 2 819 40 120

DENMARKAktieselskabet ESABHerlevTel: +45 36 30 01 11Fax: +45 36 30 40 03

FINLANDESAB OyHelsinkiTel: +358 9 547 761Fax: +358 9 547 77 71

FRANCEESAB France S.A.Cergy PontoiseTel: +33 1 30 75 55 00Fax: +33 1 30 75 55 24

GERMANYESAB GmbHSolingenTel: +49 212 298 0Fax: +49 212 298 218

GREAT BRITAINESAB Group (UK) LtdWaltham CrossTel: +44 1992 76 85 15Fax: +44 1992 71 58 03

ESAB Automation LtdAndoverTel: +44 1264 33 22 33Fax: +44 1264 33 20 74

HUNGARYESAB KftBudapestTel: +36 1 20 44 182Fax: +36 1 20 44 186

ITALYESAB Saldatura S.p.A.Mesero (Mi)Tel: +39 02 97 96 81Fax: +39 02 97 28 91 81

THE NETHERLANDSESAB Nederland B.V.AmersfoortTel: +31 33 422 35 55Fax: +31 33 422 35 44

NORWAYAS ESABLarvikTel: +47 33 12 10 00Fax: +47 33 11 52 03

POLANDESAB Sp.zo.o.KatowiceTel: +48 32 351 11 00Fax: +48 32 351 11 20

PORTUGALESAB LdaLisbonTel: +351 8 310 960Fax: +351 1 859 1277

SLOVAKIAESAB Slovakia s.r.o.BratislavaTel: +421 7 44 88 24 26Fax: +421 7 44 88 87 41

SPAINESAB Ibérica S.A.Alcalá de Henares (MADRID)Tel: +34 91 878 3600Fax: +34 91 802 3461

SWEDENESAB Sverige ABGothenburgTel: +46 31 50 95 00Fax: +46 31 50 92 22

ESAB international ABGothenburgTel: +46 31 50 90 00Fax: +46 31 50 93 60

SWITZERLANDESAB AGDietikonTel: +41 1 741 25 25Fax: +41 1 740 30 55

North and South AmericaARGENTINACONARCOBuenos AiresTel: +54 11 4 753 4039Fax: +54 11 4 753 6313

BRAZILESAB S.A.Contagem--MGTel: +55 31 2191 4333Fax: +55 31 2191 4440

CANADAESAB Group Canada Inc.Missisauga, OntarioTel: +1 905 670 02 20Fax: +1 905 670 48 79

MEXICOESAB Mexico S.A.MonterreyTel: +52 8 350 5959Fax: +52 8 350 7554

USAESAB Welding & Cutting ProductsFlorence, SCTel: +1 843 669 44 11Fax: +1 843 664 57 48

Asia/PacificCHINAShanghai ESAB A/PShanghaiTel: +86 21 2326 3000Fax: +86 21 6566 6622

INDIAESAB India LtdCalcuttaTel: +91 33 478 45 17Fax: +91 33 468 18 80

INDONESIAP.T. ESABindo PratamaJakartaTel: +62 21 460 0188Fax: +62 21 461 2929

JAPANESAB JapanTokyoTel: +81 45 670 7073Fax: +81 45 670 7001

MALAYSIAESAB (Malaysia) Snd BhdUSJTel: +603 8023 7835Fax: +603 8023 0225

SINGAPOREESAB Asia/Pacific Pte LtdSingaporeTel: +65 6861 43 22Fax: +65 6861 31 95

SOUTH KOREAESAB SeAH CorporationKyungnamTel: +82 55 269 8170Fax: +82 55 289 8864

UNITED ARAB EMIRATESESAB Middle East FZEDubaiTel: +971 4 887 21 11Fax: +971 4 887 22 63

Representative officesBULGARIAESAB Representative OfficeSofiaTel/Fax: +359 2 974 42 88

EGYPTESAB EgyptDokki--CairoTel: +20 2 390 96 69Fax: +20 2 393 32 13

ROMANIAESAB Representative OfficeBucharestTel/Fax: +40 1 322 36 74

RUSSIALLC ESABMoscowTel: +7 095 543 9281Fax: +7 095 543 9280

LLC ESABSt PetersburgTel: +7 812 336 7080Fax: +7 812 336 7060

DistributorsFor addresses and phonenumbers to our distributors inother countries, please visit ourhome page

www.esab.com