February 16, 2017 Via E mail (75 pages) Addendum …...Refer to specification section 31 41 00 1.4.2.1 regarding lagging tolerances. Weepers and insulation should be able to be installed

Michael Pacholok, Chief Purchasing Official and Director

Purchasing & Materials Management City Hall 19th Floor, West 100 Queen Street West Toronto, Ontario M5H 2N2

Joanne Kehoe, Manager Construction Services

February 16, 2017 Via E-mail (75 pages)

Addendum No. 2

TENDER No. 345-2016

Closing: 12:00 NOON (LOCAL TIME), February 28, 2017 (REVISED)

For: the supply of all materials, equipment, labour and supervision necessary for the

construction of the Wellesley Community Centre Phase 2 Indoor Pool Addition.

Please refer to the above Tender Call document in your possession and be advised of the

following:

1.0 REVISED - Closing Date:

The closing date has been extended from February 21 to 12:00 Noon, Local Time,

February 28, 2017

The last day for questions is 1:00 pm., February 21, 2017

Additional information will follow shortly.

2.0 CLARIFICATIONS & REVISIONS, Section 4, Scope of Work:

Please refer to Architectural Addendum No. 2 dated February 15, 2017 (71 pages total)

which also includes:

Electrical Addendum ADD-E01 dated February 14, 2017 (5 pages), and

Mechanical Addendum ADD-M01 dated February 14, 2017 (1 page) and be governed accordingly.

3.0 RESPONSES TO QUESTIONS

The following are responses to questions received during the call period:

Q1. Regarding sidewalk along Bleecker Street:

1. Site Plan & Grading Plan show: Existing Sidewalk;

1 of 75

Addendum No. 2

TENDER No. 345-2016 2

2. Removal Plan shows: Remove Conc. Paving – Retain Sub-base; but it looks like the existing sidewalk at the new addition side keeps untouched;

3. Layout & Material Plan: the whole sidewalk looks all new. The illustrations above conflict. Please advise.

A1. This has been addressed in this addendum as part of ARCHITECTURAL DRAWING REVISIONS + CLARIFICATIONS.

Q2. Please note that several areas have indicated to remove existing concrete and asphalt; however no make-ups are provided for the existing assembly. Please

advise on the make-up breaking out the thickness of the different asphalt or

concrete make-ups with the granular bases.

A2. This has been addressed in this addendum as part of ARCHITECTURAL DRAWING REVISIONS + CLARIFICATIONS.

Q3. Please confirm addition F.F. elevation due to the following discrepancies:

Regarding the Finished Floor Elevation:

Grading Plan C-01 shows 111.55;

Drawing S101 says (Note 1): The Ground floor datum (+0.0) corresponds

to the finished floor of the existing building, denoted as geo. Elevation

110.95 in the SR;

Drawing A301 shows 110.95;

Survey Plan A001 shows 110.97

A3. There is a discrepancy between the as-built architectural drawings which note the ground floor FFE as 110.95 and the survey which indicates 110.97. Contractor to

verify existing FFE on site prior to the start of construction. C-01 to be corrected

to match verified FFE prior to construction. Noted revision of FFE on C-01 does

not affect the current grading or storm water management plan.

Also note that 111.55 is the correct elevation for the north-west end (existing gym

and change rooms) of the building.

Q4. Please refer to both Structural and Architectural plans and sections relating to the exterior foundation wall running along Gridline X from 10x to 16z, you are

currently showing installation of weeping tile and insulation on the exterior of the

wall; however, there are no details showing how this foundation wall will relate

to the shoring wall built directly in front. With the proximity of the wall to the

property line we believe that the foundation wall will have to be poured against

the shoring. Please review and advise.

A4. The line of shoring is indicated on plan S101 and is outboard of the property line. Refer to specification section 31 41 00 1.4.2.1 regarding lagging tolerances.

Weepers and insulation should be able to be installed in this configuration with

the noted tolerances. Contractors can propose to set the formwork directly against

2 of 75

Addendum No. 2

TENDER No. 345-2016 3

the lagging if this proves more cost effective with the understanding that details

and specifications would change to suit.

Q5. Please confirm the base material for the area of unit pavers that must be removed.

A5. As-built drawing detail 7/L-400 (not issued) indicates unit pavers on 150mm compacted granular ‘A’, 200mm compacted granular ‘B’ on compacted subgrade.

Contractor to site verify as-built conditions.

Q6. Re: Door Schedule

1) Please provide details of door types D2F, D-2G not shown with other door elevations, but is indicated on door schedule.

2) Please confirm if door ST-A2 is to have frame type F-05 as noted which is Alum or F-03 which is HM. The finish is noted as PTD so wasn't sure what

the frame material would be.

3) Door ST-1A is shown to have frame type F-03 which is shown to have a transom panel, however there is no information regarding transom in the

column "Transom", possibly this frame is to be F-01.

4) Material Type is not indicated for door 164A, please advise. 5) Door 167A references HM Doors with WD Transom, please confirm if this is

correct, possibly should be a HM Transom Panel

A6. Please note the following responses

1. D2F-D2G were mislabeled and replaced. Refer to reissued sheet A801

2. F-03 is correct. Refer to reissued sheet A801

3. F-01 is correct. Refer to reissued sheet A801

4. Door Material type is HM. Refer to reissued sheet A801

5. HM Transom Panel is correct. Refer to reissued sheet A801

Q7. Please provide specification for wood doors noted on door schedule.

A7. New specification section 08 14 00 issued with Addendum 2.

Q8. With reference to the experience and qualifications forms for the Mechanical and Electrical contractors, we noticed the requirements has been revised to

experience with indoor pool projects or Community Centres projects but the

explanation paragraph still requires indoor pool projects as a component within

a larger centre Please review and clarify

A8. The intent of the change is to recognize the experience of either having:

1. completed an indoor pool as described in the Tender documents, (pool can be stand alone or part of a larger centre – but the pool doesn't have to be part of a

larger centre), or

3 of 75

Addendum No. 2

TENDER No. 345-2016 4

2. completed a community centre with a minimum 50,000 sq. foot GFA - The community centre doesn't need to have a pool in it.

Should you have any questions regarding this addendum, please contact Mike Voelker at

[email protected].

Please attach this addendum to your RFT document and be governed accordingly. Bidders must

acknowledge receipt of all addenda on the space provided on the Tender Call Cover Page as per

the Process Terms and Conditions, Section 1, Item 8 - Addenda, of the Tender Call document.

All other aspects of the Tender remain the same.

Yours truly,

Joanne Kehoe,

Manager, Construction Services

Purchasing and Materials Management

4 of 75

mailto:[email protected]

Wellesley Community Centre Phase 2 – Pool Addition Addendum 02MacLennan Jaunkalns Miller Architects Page 1Project No. 1311 February 15, 2017

General ADD2

Addendum 02Issued February 15, 2017

Project: Wellesley Community Centre Phase 2 – Pool AdditionOwner: City of TorontoConsultant: MacLennan Jaunkalns Miller Architects

1. GENERAL

.1 This Addendum shall be attached to the front of the specifications and shall be brought to the attention of all concerned.

.2 This Addendum shall form an integral part and shall be read in conjunction with Specifications and Drawings. This Addendum shall take precedence over all requirements to the aforementioned specifications with which it may prove to be at variance.

.3 Receipt of this Addendum shall be acknowledged on the Bid Form. Failure to do so may subject the Proponent to disqualification.

.4 This Addendum Contains:

.1 Part 1: GENERAL – 1 page

.2 Part 2: ARCHITECTURAL SPECIFICATION REVISIONS + CLARIFICATIONS – 1 page

.3 Part 3: ARCHITECTURAL DRAWING REVISIONS + CLARIFICATIONS – 9 pages of Architectural Drawing Revisions and Clarifications, 21 sketches with prefix “ADD2” and 3 full size sheets (A406, A600, A801)

.4 RFI RESPONSES – Refer to the City of Toronto addendum documents

.5 Electrical Addendum ADD-E01 dated February 14, 2017 (5 pages)

.6 Mechanical Addendum ADD-M01 dated February 14, 2017 (1 page)

.7 FULL SIZE drawings reissued as included or noted in the individual addendums listed above.

5 of 75


Architectural Specifications ADD2

2. ARCHITECTURAL SPECIFICATION REVISIONS + CLARIFICATIONS

A. Section 08 14 00 – Flush Wood DoorsADD new specification section contained herein (7 pages)

B. Section 08 71 00 – Finish HardwareREVISE hardware schedule with updated version dated February 10 217 contained herein (23 pages)

C. Section 08 80 00 – Glass and GlazingADD paragraph 2.2.9:

.9 Back painted glass (GL-BP):

.1 Tempered, low-iron glass meeting requirements of ASTM C1048-12e1, kind HS, kind FT coated and uncoated, 6 mm (1/4") thick, minimum, epoxy coating on No. 2 surface, ‘MagiCoat’, by Imagic Glass.

.1 Colour: to later selection by Consultant

.2 Low iron glass acceptable Products:

.1 AGC ‘Krystal Klear’.

.2 Guardian ‘Ultraclear’.

.3 Pilkington ‘Opti-White’.

.4 PPG ‘Starphire’.

.5 Saint-Gobain ‘Diamente’.

.3 Acceptable manufacturers:

.1 Central Canadian Glass.

.2 Imagic Glass.

.4 Supply and install adhesive compatible with coating and suitable for adhering glassto substrates, as recommended by glass manufacturer.

D. Section 09 31 01 – Tiling Schedule

ADD to paragraph 1.2: (Speciality Tiles) Provide tile stair treads with custom radius edge and continuous safety strip routed into tile (both by manufacturer). Provide tile stair risers cut to suit.

END OF ARCHITECTURAL SPECIFICATION REVISIONS + CLARIFICATIONS.

6 of 75

Wellesley Community Centre Phase 2: Pool Addition Section 08 14 00City of Toronto Page 1Project No. 1311 February 15, 2017

Flush Wood DoorsSection issued by Addendum No. 02

PART 1 - GENERAL

1.1 Summary

.1 Section includes:

.1 Solid core doors with wood veneer.

.2 Factory finishing wood doors.

.3 Fire rated wood doors.

1.2 Submittals

.1 Submit required submittals in accordance with Section 01 33 00.

.2 Product data sheets:

.1 Submit manufacturer’s Product data sheets for Products proposed for use in thework of this section.

.3 Shop drawings:

.1 Indicate door location using numbering system per door schedule, size, and handof each door, elevation of each door type; undercuts, bevelling, construction typecore and edge construction not covered in product data; and special blockingrequirements.

.2 Indicate dimensions and locations of factory machining criteria for hardware, extentof hardware blocking.

.3 Indicate dimensions and locations of cut-outs including trim for openings.

.4 Indicate door face finish requirements including veneer matching.

.5 Indicate doors to be factory finished and finish requirements.

.6 Indicate fire ratings for fire rated doors.

.7 Indicate electrified hardware requirements and preparations.

.4 Verification samples:

.1 Submit cut-away sample of each type of door, to show stile and rail construction,core, cross banding, door face finish and edges.

.2 Submit solid lumber frames for light openings, minimum 150 mm (6") long, for eachmaterial, type and finish required.

1.3 Quality Assurance

.1 Quality standard:

.1 Work shall be in accordance with the Architectural Woodwork Standards Edition2-2014, Premium Grade.

1.4 Delivery, Storage, and Handling

.1 Door numbers shall be marked with door numbers used on shop drawings in the top hingecavity created by the machining for hinges.

7 of 75



.2 Identify doors with labels. Package with resilient packaging.

.3 Store doors flat at the Place of the Work in piles with bottom face on bottom of pile. Protectfrom moisture by placing water resistant material under skids supporting piles. Cover topof piles and provide air at sides of piles.

.4 Deliver the wood doors only after the building is closed and dry and HVAC system isoperating and maintaining ambient temperature and humidity conditions at occupancylevels during the remainder of the construction period. Do not receive the doors in a damparea. Do not drag the doors on the ground, floor or across one another.

PART 2- PRODUCTS

2.1 Manufacturer

.1 Algoma Hardwoods, Inc.

.2 Baillargeon Doors, Inc.

.3 DoorLam Manufacturing.

.4 Eggers Industries.

.5 JWS Manufacturing Inc.

.6 Lambton Doors.

.7 Marshfield Door Systems.

.8 Mohawk Flush Doors, Inc.

.9 Substitutions: in accordance with Section 01 25 00.

2.2 Performance/Design Requirements – Fire Rating Requirements

.1 Fire rated doors shall be fabricated, labelled and listed by an organization accredited byStandards Council of Canada in conformance with CAN/ULC-S104-10 and CAN/ULC-S105-09 for fire protection ratings as scheduled.

.2 Install fire rated doors in accordance with NFPA 80-2010.

2.3 General

.1 Single-source manufacturing and fabrication responsibility: Engage a qualifiedManufacturer to assume undivided responsibility for wood doors specified in this section,including fabrication and finishing except where site finishing is specified.

2.4 Fabrication – Door Construction

.1 Performance duty level:

.1 Doors shall meet the requirements of ANSI/WDMA I.S. 1A-13 for Heavy DutyPerformance Level unless otherwise indicated or scheduled.

.2 Solid particleboard core, veneer faced, non fire rated and 20 minute fire rated wood doorconstruction to Architectural Woodwork Standards Manual, Section 9 and as follows:

.1 Type PC-5, particle board core to ANSI A208.1-2009 LD-2 (minimum 529 kg/m3(33 lbs/ft3) density).

8 of 75



.3 Solid fire resistant core; veneer faced, construction to Architectural Woodwork StandardsManual, Section 9 and as follows:

.1 45, 60 and 90 minute rated doors; Type FD-5, non-combustible mineral core.

.4 Bonding:

.1 Bond stiles and rails to core; abrasive sand core assembly to achieve uniformthickness prior to lamination of door faces.

.5 Panel edge types:

.1 Wood veneer faced doors for transparent finish:

.1 For vertical edges (stiles) and exposed horizontal edges (rails). (Exposedhorizontal edges are those edges that can be viewed from floors above.):

.1 Edge Type A: Minimum 11 mm (7/16") thick solid hardwood, species tomatch face veneer, and referenced quality standard.

.2 Inset solid wood edging shall have consistent moisture content as panelcore material, be glued securely, and calibrated with panel core thicknessprior to being laminated with wood veneer on both sides.

.3 Non rated or 20 minute fire rated doors: Solid hardwood edge to belaminated to minimum 25.4 mm (1") structural composite lumber backer.

.4 45, 60, or 90 minute fire rated doors: Solid hardwood edge to be laminatedto Tectonite or manufacturer’s standard fire rated material for fire rateddoors

.2 For unexposed horizontal edges (rails):

.1 Non rated or 20 minute fire rated doors: Minimum 25 mm (1") structuralcomposite lumber.

.2 45, 60, or 90 minute fire rated doors: Tectonite or manufacturer’s standardfire rated material for fire rated doors.

.3 Minimum 11 mm (7/16") thick, closed grain, solid hardwood edge.

.1 Wood edge transparent finish to match face.

.4 Non-rated or 20 minute fire rated doors: Solid hardwood edge to be laminatedto minimum 25.4 mm (1") structural composite lumber backer.

.5 For 45, 60, or 90 minutes fire rated doors: Solid hardwood edge to belaminated to Tectonite or manufacturer’s standard fire rated material for firerated doors

.6 Blocking:

.1 Provide hardware blocking for doors as follows:

.1 Non-rated or 20 minute fire rated doors: Structural composite lumber forhardware blocking.

.2 45, 60, and 90 minute fire rated doors: Tectonite or manufacturer’s standardfire rated material for hardware blocking.

9 of 75



.3 HB-1, minimum 125 mm (5") wide, full door width, top-rail blocking for closuredevices or flush bolts or for sliding door hardware.

.4 HB-2, minimum 125 mm (5") wide, full door width, bottom-rail blocking fordoors with protection plates, concealed door seals, automatic bottoms, pivotsor floor bolts.

.5 HB-4, minimum 125 mm (5") wide x 250 mm (10") high blocking for doors withmortise locks and pockets.

.6 HB-5, minimum 125 mm (5") wide x 250 mm (10") high blocking for hinges.

.7 HB-6, minimum 125 mm (5") wide, full door width, mid-rail blocking for exitdevices.

.8 HB-7, minimum 125 mm (5") wide, full door height, for doors with continuoustype hinges.

.7 Thickness:

.1 45 mm (1-3/4") minimum unless otherwise indicated or scheduled.

2.5 Veneer Faced Doors For Transparent Finish

.1 Veneer face grade: Allowable wood veneer face grade characteristics shall comply withArchitectural Woodwork Standards, Edition 1, 2009 referenced grade and referencedstandards.

.1 AA.

.2 Veneer thickness: Minimum 1.02 mm (0.040") thick after sanding.

.3 Veneer species: Maple.

.4 Veneer cut: Quarter.

.5 Veneer leaf matching: Book.

.6 Veneer assembly matching: Balance.

2.6 Accessories

.1 Wood glass stops: Solid hardwood, species to match face finish, and referenced qualitystandard.

.2 Finishing hardware: in accordance with Section 08 71 00.

2.7 Fabrication

.1 Fire rated doors shall be fabricated, labelled and listed by an organization accredited byStandards Council of Canada in conformance with CAN/ULC-S104-10 and CAN/ULC-S105-09 for fire protection ratings as scheduled.

.2 Align and fit doors in frames with uniform clearances and bevels as indicated below; donot trim stiles and rails in excess of limits set by manufacturer or permitted for fire-rateddoors. Seal edges of doors, edges of cutouts, and mortises after fitting and machining.

.1 Clearances: Refer to Part 3 for clearance tolerances.

.2 Fit doors for automatic door bottoms.

10 of 75



.3 Comply with NFPA 80-2010 for fire-rated doors.

.4 Bevel non-fire-rated doors 3-1/2 degrees (1/8 inch in 2 inches) at lock and hingeedges.

.5 Bevel fire-rated doors 3-1/2 degrees (1/8 inch in 2 inches) at lock edge; trim stilesand rails only to extent permitted by labelling agency.

.3 Fabricate doors with hardware blocking as specified in Part 2 of this Section.

.4 Factory machine doors for finish hardware that is not surface applied. Do not machine forsurface hardware. Locate hardware to comply with Door and Hardware Institute (DHI)“Recommended Locations for Architectural Hardware for Flush Wood Doors (latestedition). Comply with final reviewed hardware schedules, door and frame shop drawingsand hardware templates.

.1 Coordinate with hardware mortises in metal frames to verify dimensions andalignment before factory machining.

.2 Metal astragals: Factory machine astragals and formed-steel edges for hardwarefor pairs of fire rated doors.

.5 Electrified hardware: Where electrically or electronically operated hardware is specifiedon the schedules or details or the final approved schedule and templates provided by thehardware supplier, doors with electrified devices shall be manufactured to include wireraceway in door panel to accommodate electrified devices, such as electric hinge, powertransfer units, electrified locks, electrified door closures and electrified exit devices.Construction of raceways shall provide a continuous conduit or channel between entryand exit points to accommodate wire installation after door manufacture.

.6 Factory cut and trim openings.

.1 Glazing: Factory install glazing in doors indicated to be factory finished.

.7 Transom and side panels:

.1 Fabricate matching panels with same construction, exposed surfaces, and finishas specified for associated doors. Finish bottom edges of transoms and top edgesof rabbeted doors same as door stiles.

2.8 Factory Finishing

.1 Finish work in factory in accordance with Architectural Woodwork Standards Manual,Section 9 and referenced quality standard.

.2 Prior to finishing, handling marks or effects of exposure to moisture removed with athorough final sanding over surfaces of the exposed portions, using appropriate gritsandpaper, and shall be cleaned prior to applying sealer or finish. Sanding shall becompleted just prior to stain or finishing application.

.3 Comply with requirements indicated below for finish system, staining, and sheen.

.1 Sheen; Sheen range measurements in accordance with Architectural WoodworkStandards, Edition 2, 2014:

.1 Satin.

11 of 75



.2 Factory finish with transparent, Post Catalyzed Lacquer in accordance with theArchitectural Woodwork Standards, Edition 1, 2009, Section 5.

.1 Transparent finish:

.1 Clear (natural).

.2 Stain: Stain colour as selected by Consultant.

.4 Seal top and bottom door edges.

PART 3 - EXECUTION

3.1 Examination

.1 Provide necessary grounds, bracing and strapping for fitting and adequate for securing ofthe work.

.2 Cooperate with work of other sections to ensure fastenings set by others are provided andlocated, their work is installed to their specifications and that those responsible for backpriming are notified in sufficient time for them to schedule work.

3.2 Installation - General

.1 Execute installation and assembly at the Place of the Work using skilled forces undersupervision of a competent joinery foreperson.

.2 Install work plumb, level and straight, and fasten it securely to backing to support itselfand anticipated superimposed loads.

.3 Build into construction as indicated, or specified in other sections of this specification, orboth.

.4 Adequately fasten units and secure in place with concealed fixings wherever possible.Include grounds and furring where required.

3.3 Installation – Doors/Frames

.1 Install fire rated doors in accordance with NFPA 80-2010.

.2 Install wood doors after finishing of walls.

.3 Align and fit doors in frames with uniform clearances as indicated below; do not trim stilesand rails in excess of limits set by manufacturer or permitted for fire-rated doors. Machinedoors for hardware. Seal edges of doors, edges of cutouts, and mortises after fitting andmachining.

.1 Clearances:

.1 Provide 3.2 mm (1/8") maximum clearance between door and frame at heads,jambs, and between pairs of doors.

.2 Provide minimum 3.2 mm (1/8") maximum clearance from bottom of door totop of decorative floor finish or covering unless otherwise indicated..

.3 Where threshold is shown or scheduled, 6.4 mm (1/4") minimum from bottomof door to top of threshold unless otherwise indicated and a maximum of12.7 mm (1/2").

12 of 75



.2 Comply with NFPA 80 for fire-rated doors.

.4 Seal top and bottom edges of wood doors if they are cut to fit, in accordance with doormanufacturer’s warranty requirements.

.5 Pilot drill screw and bolt holes.

.6 Coordinate installation of doors with installation of frames specified in Section 08 11 13,and hardware specified in Section 08 71 00.

3.4 Installation - Finishing Hardware

.1 Install finishing hardware in accordance with Section 08 71 00.

3.5 Adjusting and Cleaning

.1 Adjust doors to swing freely, smoothly and easily, to remain stationary at any point, toclose evenly and tightly against stops without binding, and to latch positively when doorsare closed with moderate force.

.2 Adjust hardware so that latches and locks operate smoothly and without binding, andclosers act positively with the least possible resistance in use. Lubricate hardware ifrequired by Supplier’s instructions.

.3 Ensure that doors equipped with closers operate to close doors firmly against anticipatedwind and building air pressure, and to enable doors to be readily opened as suitable forfunction, location and traffic.

.4 Clean hardware after installation in accordance with Supplier’s instructions.

END OF SECTION

13 of 75

/10/17

Upper Canada Specialty Hardware7100 Warden Ave.Unit 1Markham, Ontario, L3R 8B5

Wellesley Community CentrePhase 2 - Pool Addition

Submittal Date: February 10, 2017


ArchitectMacLennan Jaunkalns Miller Architects

425 Adelaide Street WestLevel 6

Toronto, OntarioM5V 3C1

Tel: 416-593-6796

CoordinatorMark Di Plama

Tel: 905-940-8358 Ext: 205Fax: 905-940-8362

Email: [email protected]

Consultant-----------------

Brian Hughes Tel: 647-502-7955Fax: 905-940-8362

E-Mail: [email protected]


14 of 75

/10/17




Openings Schedule

HardwareGroup Qty

OpeningNumber(s) Location 1

To/From Location 2 Hand

DoorType

NominalWidth

NominalHeight

DoorThickness

DoorMat'l

FrameMat'l Label

001 1 B61 CORRIDOR B60 FROM STORAGE B61 LHR/RHRA D2/F02 900, 900 2350 45 HM HM

002 1 B62 STORAGE B61 FROM HOISTWAY ACCESS B62 LHR/RHRA D2/F02 900, 900 2350 45 HM HM 45 MIN

003 1 B63 CORRIDOR B60 FROM MECHANICAL B63 LHR/RHRA D2/F02 900, 900 2150 45 HM HM 45 MIN

004 1 B68 FILTRATION RM B65 TO GROUND HEAT EXCHANGE B68 RH D1/F01 1000 2350 45 HM HM 45 MIN

005 1 STA-O STAIR FROM CORRIDOR B60 RHR D3/F01 1000 2350 45 HM HM 45 MIN

006 1 060A ATHLETIC CORRIDOR 031 TO ENTRY 060 SLIDER D11 3020 3000 WD -

007 1 060B ENTRY 060 TO UNIVERSAL CHANGE ROOM 064 SLIDER D5 2134 2352 AL AL

008 1 060C ENTRY 060 TO UNIVERSAL CHANGE ROOM 077 SLIDER D5 2134 2352 AL AL

009 1 061B ENTRY 060 TO RECEPTION 061 LH D1/F01 1000 2350 45 HM HM

010 1 062 STAFF KITCHEN 062 TO AQUATIC STAFF 063 LH D1/F01 1000 2350 45 HM HM

011 1 062A STAFF KITCHEN 061 FROM ELECT CLOSET 062A LHR/RHRA D2/F02 900, 900 2350 45 HM HM

012 1 063 POOL HALL 072 TO AQUATIC STAFF 063 RH D4/F05 1000 2350 45 AL AL

012A 1 064A EXIST ATHLETIC CORRIDOR 031 FROM UNIVERSAL CHANGE ROOM B 064 RHR D6 1050 2245 45 AL AL

012B 1 064B UNIVERSAL CHANGE ROOM B 064 TO SHOWER 069 O/H D10 1210 2400 45 AL AL

013 1 065 UNIVERSAL CHANGE ROOM 064 TO UNIVERSAL TOILET/CHANGE 065 RH D1/F01 1000 2350 45 HM HM

014 1 067 CORRIDOR 066 FROM ACCESSIBLE W/C 067 LHR D1/F01 950 2350 45 HM HM

015 1 068 CORRIDOR 066 FROM ACCESSIBLE W/C 068 LHR D1/F01 950 2350 45 HM HM

016 1 069A UNIVERSAL CHANGE ROOM 064 FROM SHOWER 069 O/H D10 1200 3200 AL -

017 1 069 POOL HALL 072 FROM SHOWER 069 O/H D10 1610 3200 AL -

018 1 070 EXTERIOR TO CHOLRINE STORAGE 070 RH D1/F01 900 2350 45 HM HM

019 1 071 EXTERIOR FROM HOISTWAY SHAFT 071 LHR/RHRA D2/F02 900, 900 2350 45 HM HM

020 1 072 ENTRY 006 FROM VIEW IN AREA 072 RHR D4/F05 900, 900 2650 45 AL AL

020A 1 072B POOL HALL FROM STAIR B RH 915 1800 13 GL -

021 1 073A POOL HALL 072 FROM POOL STORAGE 073 RHR D1/F01 1210 2150 45 HM HM

022 1 073B POOL HALL 072 FROM POOL STORAGE 073 LHR D1/F01 1210 2150 45 HM HM

023 1 075 POOL HALL 072 FROM POOL STORAGE 075 RHR D2A/F06 800 2350 45 AL AL

024 1 076 POOL HALL 072 TO STEAM ROOM 076 RH D4/F05 1000 2350 45 AL AL

024A 1 077A EXIST ATHLETIC CORRIDOR 031 FROM UNIVERSAL CHANGE ROOM A 077 LHR D6 1050 2845 45 AL AL

024B 1 077B UNIVERSAL CHANGE ROOM A 077 TO SHOWER 082 O/H D-10 1210 2400 45 AL -

025 1 078 UNIVERSAL CHANGE ROOM 077 TO UNIVERSAL TOILET/CHANGE 078 LH D1/F01 1000 2150 45 HM HM

026 1 080 CORRIDOR 079 FROM ACCESSIBLE W/C 080 RHR D1/F01 950 2350 45 HM HM

027 1 081 CORRIDOR 079 FROM ACCESSIBLE W/C 081 RHR D1/F01 950 2350 45 HM HM

028 1 082A UNIVERSAL CHANGE ROOM 077 FROM SHOWER 082 O/H D10 1200 2400 AL -

029 1 082B POOL HALL 072 FROM SHOWER 082 O/H D10 1550 3200 AL -

030 1 083 NEW VESTIBULE EXIT 083 FROM POOL HALL 072 LHR D4/F05 1000 2650 45 AL AL

031 1 083B EXTERIOR FROM NEW VESTIBULE EXIT 083 LHR D3A/F04 1048 2660 45 WD HM

032 1 ST-A1 STAIR A1 FROM POOL HALL 072 RHR D3 1000 2350 45 HM HM 45 MIN

033 1 ST-A1B EXTERIOR FROM STAIR A1 RHR D1 1000 2350 45 HM HM

034 1 160A CORRIDOR 160 FROM MECHANICAL LHR D2A/F03 1000 2250 45 HM HM

035 1 160B MECHANCIAL TO GREEN ROOF RH D1/F01 1000 2350 45 HM HM

036 1 161 CORRIDOR 160 TO ELECTRICAL 161 RH D2A/F03 1000 2250 45 HM HM 45 MIN

037 1 162 CORRIDOR 160 FROM OFFICE 162 LHR D2A/F05 1000 2250 45 WD AL

038 1 163 OFFICE 162 TO LAN ROOM 163 LH D1/F01 1000 2350 45 HM HM

039 1 164 CORRIDOR 160 FROM MULTI-PURPOSE 164 LHR D2A/F05 1000 2250 45 WD AL

039A 1 164A MULTI-PURPOSE 164 FROM STORAGE 164A RHR D2A/F3 1000 2250 45 HM HM

039B 1 165 2ND FLOOR CORRIDOR 160 TO UNISEX WC 165 RH D2A/F3 1000 2250 45 WD WD

15 of 75

/10/17




HardwareGroup Qty

OpeningNumber(s) Location 1

To/From Location 2 Hand

DoorType

NominalWidth

NominalHeight

DoorThickness

DoorMat'l

FrameMat'l Label

040 1 165A MULTI-PURPOSE 164 FROM STORAGE 165 LHR/RHRA D2A/F04 900, 900 2250 45 HM HM

041 1 165B MULTI-PURPOSE 166 FROM STORAGE 163 LHR/RHRA D2B/F04 900, 900 2350 45 WD HM

042 1 166A CORRIDOR 160 FROM MULTI-PURPOSE 166 LHR D2A/F05 1000 2250 45 WD AL

043 1 166B CORRIDOR 160 FROM MULTI-PURPOSE 166 LHR D2A/F05 1000 2250 45 WD AL

044 1 167A MULTI-PURPOSE 166 FROM STORAGE 167 LHR/RHRA D2B/F04 900, 900 2250 45 HM HM

045 1 168 CORRIDOR 160 TO ACCESSIBLE W/C 168 RH D2A/F03 1000 2250 45 HM HM

046 1 168A 1 - -

047 1 ST-A2 STAIR A2 FROM CORRIDOR 160 LHR D3/F05 900 2250 45 HM HM 45 MIN

16 of 75

/10/17




Hardware Schedule

Heading #001

1 Pair of doors B61, CORRIDOR B60 FROM STORAGE B61 LHR/RHRA

Type: D2/F02, 900, 900 x 2350 x 45 - HM DR x HM FR

8 Standard Hinge STSCB1391 114 x 101 NRP 32D 32D1 Lockset L9080HD 07B 630 RHR 6301 Cylinder Cyl. Schlage Everest B123 Keyed to Exist. MK System2 Flush Bolt GSH 401-12" C26D C26D1 Surface Closer 4050 PA AL DEL AL2 Kick Plate GSH 80A C32D (200 X 876) RC TM C32D2 Wall Door Stop GSH 240B C32D C32D

Heading #002

1 Pair of doors B62, STORAGE B61 FROM HOISTWAY ACCESS B62 LHR/RHRA

Type: D2/F02, 900, 900 x 2350 x 45 - HM DR x HM FR - 45 MIN

8 Standard Hinge STSCB1391 114 x 101 NRP 32D 32D1 Latchset L9010 07B 630 RHR 6302 Flush Bolt FB458-24 ULC C26D C26D1 Surface Closer 4050 PA AL DEL AL1 Overhead Door Stop 904S C32D (110 Deg.) C32D

(Inactive leaf)2 Kick Plate GSH 80A C32D (200 X 876) RC TM C32D1 Wall Door Stop GSH 240B C32D C32D

(Active leaf)

17 of 75

/10/17




Heading #003

1 Pair of doors B63, CORRIDOR B60 FROM MECHANICAL B63 LHR/RHRA

Type: D2/F02, 900, 900 x 2150 x 45 - HM DR x HM FR - 45 MIN

6 Standard Hinge STSCB1391 114 x 101 NRP 32D 32D1 Lockset L9080HD 07B 630 RHR 6301 Cylinder Cyl. Schlage Everest B123 Keyed to Exist. MK System2 Flush Bolt FB458-24 ULC C26D C26D1 Surface Closer 4050 PA AL DEL AL1 Overhead Door Stop 904S C32D (110 Deg.) C32D

(Inactive leaf)2 Kick Plate GSH 80A C32D (200 X 876) RC TM C32D1 Wall Door Stop GSH 240B C32D C32D

(Active leaf)

Heading #004

1 Single door B68, FILTRATION RM B65 TO GROUND HEAT EXCHANGE B68 RH

Type: D1/F01, 1000 x 2350 x 45 - HM DR x HM FR - 45 MIN

4 Standard Hinge STSCB1399 114 X 101 NRP 32D 32D1 Lockset L9080HD 07B 630 RH 6301 Cylinder Cyl. Schlage Everest B123 Keyed to Exist. MK System1 Surface Closer 4050 REG AL AL1 Kick Plate GSH 80A C32D (200 X 965) RC TM C32D1 Wall Door Stop GSH 240B C32D C32D

18 of 75

/10/17




Heading #005

1 Single door STA-O, STAIR FROM CORRIDOR B60 RHR


4 Standard Hinge STSCB1399 114 X 101 NRP 32D 32D1 Exit Device 98-L-NL-F C26D 996L-NL-R C26D RHR #07 Lever 1000 x 2350 Door C26D/C26D1 Cylinder Cyl. Schlage Everest B123 Keyed to Exist. MK System1 Rim Cylinder 80-159 6261 Surface Closer 4050 REG AL AL1 Kick Plate GSH 80A C32D (200 X 965) RC TM C32D1 Wall Door Stop GSH 240B C32D C32D1 Door Contact 1078-1 BRN BRN

Heading #006

1 Single door 060A, ATHLETIC CORRIDOR 031 TO ENTRY 060 SLIDER

Type: D11, 3020 x 3000 x __ - WD DR x - FR

DOOR DELETED

Heading #007

1 Single door 060B, ENTRY 060 TO UNIVERSAL CHANGE ROOM 064 SLIDER

Type: D5, 2134 x 2352 x __ - AL DR x AL FR

COMPLETE BY MANUFACTURER

Heading #008

1 Single door 060C, ENTRY 060 TO UNIVERSAL CHANGE ROOM 077 SLIDER

Type: D5, 2134 x 2352 x __ - AL DR x AL FR

COMPLETE BY MANUFACTURER

19 of 75

/10/17




Heading #009

1 Single door 061B, ENTRY 060 TO RECEPTION 061 LH

Type: D1/F01, 1000 x 2350 x 45 - HM DR x HM FR

3 Standard Hinge STSCB1391 114 x 101 NRP 32D 32D1 Lockset L9070HD 07B 630 LH 6301 Cylinder Cyl. Schlage Everest B123 Keyed to Exist. MK System1 Surface Closer 4050 PA AL DEL AL1 Kick Plate GSH 80A C32D (200 X 965) RC TM C32D1 Wall Door Stop GSH 240B C32D C32D1 Door Contact 1078-1 BRN BRN

Heading #010

1 Single door 062, STAFF KITCHEN 062 TO AQUATIC STAFF 063 LH


3 Standard Hinge STSCB1391 114 x 101 NRP 32D 32D1 Lockset L9070HD 07B 630 LH 6301 Cylinder Cyl. Schlage Everest B123 Keyed to Exist. MK System1 Surface Closer 4050 PA AL DEL AL1 Kick Plate GSH 80A C32D (200 X 965) RC TM C32D1 Wall Door Stop GSH 240B C32D C32D

Heading #011

1 Pair of doors 062A, STAFF KITCHEN 061 FROM ELECT CLOSET 062A LHR/RHRA


8 Standard Hinge STSCB1391 114 x 101 NRP 32D 32D1 Lockset L9080HD 07B 630 RHR 6301 Cylinder Cyl. Schlage Everest B123 Keyed to Exist. MK System2 Flush Bolt FB458-24 ULC C26D C26D2 Overhead Door Stop 452S C32D (110 Deg,) C32D

20 of 75

/10/17




Heading #012

1 Single door 063, POOL HALL 072 TO AQUATIC STAFF 063 RH

Type: D4/F05, 1000 x 2350 x 45 - AL DR x AL FR

1 Continuous Hinge SL11 CL HD x 2350 CL1 Set Door Pull GSH 1180-2 BTB C32D C32D1 Dead Lock MS1850S-210-628 - RH 6281 Cylinder Cyl. Schlage Everest B123 Keyed to Exist. MK System1 Mortise Cylinder 80-113 6261 Thumb Turn Cylinder 4066-01-130 1301 Surface Closer 4050 REG AL AL1 Mounting Plate 4050-18 AL AL1 Wall Door Stop GSH 240B C32D C32D1 Door Contact 1078-1 BRN BRN

Heading #012A

1 Single door 064A, EXIST ATHLETIC CORRIDOR 031 FROM UNIVERSAL CHANGE ROOM B 064 RHR

Type: D6, 1050 x 2245 x 45 - AL DR x AL FR

1 Continuous Hinge SL40 BLACK HD x 2220 BLACK1 Exit Device 35A-EO C26D RHR 4' Bar 1050 x 2245 Door C26D1 Door Closer 4050 S CUSH x 61 Spacer AL AL

NOTE:HARDWARE TO BE REVIEWED AND CONFIRM.

Heading #012B

1 Single door 064B, UNIVERSAL CHANGE ROOM B 064 TO SHOWER 069 O/H


OVERHEAD DOOR

ALL HARDWARE COMPLETE BY DOOR SUPPLIER

21 of 75

/10/17




Heading #013

1 Single door 065, UNIVERSAL CHANGE ROOM 064 TO UNIVERSAL TOILET/CHANGE 065 RH


3 Standard Hinge STSCB1399 114 X 101 NRP 32D 32D1 Lockset L9080HD 07B 630 RH 6301 Cylinder Cyl. Schlage Everest B123 Keyed to Exist. MK System1 Electric Strike 4500C-FS-24VDC-630-LBM 630-LBM1 Auto Door Operator 8500 628 (Pull Side) 6282 Actuator 6R3 630 6301 Indicator CM-AF5001 Push-to-Lock Button CM-400/81 Relay CX-EMF-21 LED Annunciator CM-AF501501 Assistance Requied Light CM-AF140501 Emergency Sign CM-SE21A1 Emergency Strip Nexgen Emerg Strip x 610mm1 Relay TA-2871 - For Emergency Strip1 Power Supply CX-PS313 V31 Kick Plate GSH 80A C32D (200 X 965) RC TM C32D1 Wall Door Stop GSH 240B C32D C32D

Heading #014

1 Single door 067, CORRIDOR 066 FROM ACCESSIBLE W/C 067 LHR


4 Standard Hinge STSCB1391 114 x 101 NRP 32D 32D1 Privacy Set L9040 07B 630 LHR 6301 Overhead Door Stop 905S C32D C32D1 Kick Plate GSH 80A C32D (200 x 912) RCTM C32D

22 of 75

/10/17




Heading #015

1 Single door 068, CORRIDOR 066 FROM ACCESSIBLE W/C 068 LHR


4 Standard Hinge STSCB1391 114 x 101 NRP 32D 32D1 Privacy Set L9040 07B 630 LHR 6301 Overhead Door Stop 905S C32D C32D1 Kick Plate GSH 80A C32D (200 x 912) RCTM C32D

Heading #016

1 Single door 069A, UNIVERSAL CHANGE ROOM 064 FROM SHOWER 069 O/H

Type: D10, 1200 x 3200 x __ - AL DR x - FR

DOOR DELETED

Heading #017

1 Single door 069, POOL HALL 072 FROM SHOWER 069 O/H

Type: D10, 1610 x 3200 x __ - AL DR x - FR

OVERHEAD DOOR

COMPELTE BY DOOR SUPPLIER

23 of 75

/10/17




Heading #018

1 Single door 070, EXTERIOR TO CHOLRINE STORAGE 070 RH


4 Standard Hinge STSCB1399 114 X 101 NRP 32D 32D1 Lockset L9080HD 07B 630 RH 6301 Cylinder Cyl. Schlage Everest B123 Keyed to Exist. MK System1 Surface Closer 4050 REG AL AL1 Floor Door Stop GSH 209 C26D C26D1 Door Sweep W-24S-CA x 900 CA1 Threshold CT-45 x 9001 Weatherstripping W-20S-CA 1 x 900 + 2 x 2350 CA1 Door Contact 1078-1 BRN BRN

Heading #019

1 Pair of doors 071, EXTERIOR FROM HOISTWAY SHAFT 071 LHR/RHRA


8 Standard Hinge STSCB1399 114 X 101 NRP 32D 32D1 Lockset L9080HD 07B 630 RHR 6301 Cylinder Cyl. Schlage Everest B123 Keyed to Exist. MK System2 Flush Bolt GSH 401-12" C26D C26D1 Surface Closer 4050 S CUSH AL AL2 Kick Plate GSH 80A C32D (200 X 876) RC TM C32D1 Threshold CT-45 x 18001 Weatherstripping W-20S-CA 1 @ 1800 + 2 @ 2350 CA2 Door Sweep W-24S-CA x 900 CA1 Astragal W-5 x 23502 Door Contact 1078-1 BRN BRN

24 of 75

/10/17




Heading #020

1 Single door 072, ENTRY 006 FROM VIEW IN AREA 072 RHR

Type: D4/F05, 900, 900 x 2650 x 45 - AL DR x AL FR

2 Continuous Hinge SL11 CL HD x 26251 Dead Lock MS1850S-210-628 6281 Thumb Turn Cylinder 4066-01-130 1301 Cylinder Cyl. Schlage Everest B123 Keyed to Exist. MK System1 Mortise Cylinder 80-113 6261 Set Door Pull GSH 1180-2 BTB C32D C32D2 Surface Closer 4050 PA AL DEL AL1 Flush Bolts Flush Bolts - By Door Supplier2 Mounting Plate 4050-18TJ AL AL1 Wall Door Stop GSH 240B C32D C32D2 Door Contact 1078-1 BRN BRN

Heading #020A

1 Elevation 072B, POOL HALL FROM STAIR B RH

915 x 1800 x 13 - GL DR x - FR

1 Hinge Tensor 812.520.1141 Patch Lock S104 B C32D C32D1 Mortise Cylinder 80-131 x B520-296 6261 Cylinder Cyl. Schlage Everest B123 Keyed to Exist. MK System1 Strike GSH Custom ASA Strike w/ Stop

Heading #021

1 Single door 073A, POOL HALL 072 FROM POOL STORAGE 073 RHR


1 Continuous Hinge SL11 CL HD x 21251 Lockset L9080HD 07B 630 RHR 6301 Cylinder Cyl. Schlage Everest B123 Keyed to Exist. MK System1 Overhead Door Stop 906S C32D C32D

25 of 75

/10/17




Heading #022

1 Single door 073B, POOL HALL 072 FROM POOL STORAGE 073 LHR


1 Continuous Hinge SL11 CL HD x 21251 Lockset L9080HD 07B 630 LHR 6301 Cylinder Cyl. Schlage Everest B123 Keyed to Exist. MK System1 Overhead Door Stop 906S C32D C32D

Heading #023

1 Single door 075, POOL HALL 072 FROM POOL STORAGE 075 RHR

Type: D2A/F06, 800 x 2350 x 45 - AL DR x AL FR

1 Continuous Hinge SL11 CL HD x 21251 Lockset L9080HD 07B 630 RHR 6301 Cylinder Cyl. Schlage Everest B123 Keyed to Exist. MK System1 Overhead Door Stop 905S C32D C32D

Heading #024

1 Single door 076, POOL HALL 072 TO STEAM ROOM 076 RH


1 Continuous Hinge SL11 CL HD x 2350 CL1 Cylinder Cyl. Schlage Everest B123 Keyed to Exist. MK System1 Mortise Cylinder 80-113 6261 Dead Lock MS1850S-210-628 - RH 6281 THUMBTURN CYLINDER 09-900 X AR CAM 626 6261 Set Door Pulls GSH 165F x 165F Wood BTB Oak OAK1 Roller Latch GSH 404H S C32D S C32D

NOTE:WEATHER SEAL COMPLETE BY DOOR MANUFACTURER

26 of 75

/10/17




Heading #024A

1 Single door 077A, EXIST ATHLETIC CORRIDOR 031 FROM UNIVERSAL CHANGE ROOM A 077 LHR


1 Continuous Hinge SL40 BLACK HD x 2820 BLACK1 Exit Device 35A-EO C26D LHR 4' Bar 1050 x 2845 Door C26D1 Door Closer 4050 S CUSH x 61 Spacer AL AL

NOTE:HARDWARE TO BE REVIEWED AND CONFIRM.

Heading #024B

1 Single door 077B, UNIVERSAL CHANGE ROOM A 077 TO SHOWER 082 O/H

Type: D-10, 1210 x 2400 x 45 - AL DR x - FR

OVERHEAD DOOR

ALL HARDWARE COMPLETE BY DOOR SUPPLIER

27 of 75

/10/17




Heading #025

1 Single door 078, UNIVERSAL CHANGE ROOM 077 TO UNIVERSAL TOILET/CHANGE 078 LH


3 Standard Hinge STSCB1399 114 X 101 NRP 32D 32D1 Lockset L9080HD 07B 630 LH 6301 Cylinder Cyl. Schlage Everest B123 Keyed to Exist. MK System1 Electric Strike 4500C-FS-24VDC-630-LBM 630-LBM1 Auto Door Operator 8500 628 (Pull Side) 6282 Actuator 6R3 630 6301 Indicator CM-AF5001 Push-to-Lock Button CM-400/81 Relay CX-EMF-21 LED Annunciator CM-AF501501 Assistance Requied Light CM-AF140501 Emergency Sign CM-SE21A1 Emergency Strip Nexgen Emerg Strip x 610mm1 Relay TA-2871 - For Emergency Strip1 Power Supply CX-PS313 V31 Kick Plate GSH 80A C32D (200 X 965) RC TM C32D1 Wall Door Stop GSH 240B C32D C32D

Heading #026

1 Single door 080, CORRIDOR 079 FROM ACCESSIBLE W/C 080 RHR


4 Standard Hinge STSCB1391 114 x 101 NRP 32D 32D1 Privacy Set L9040 07B 630 RHR 6301 Overhead Door Stop 905S C32D C32D1 Kick Plate GSH 80A C32D (200 x 912) RCTM C32D

28 of 75

/10/17




Heading #027

1 Single door 081, CORRIDOR 079 FROM ACCESSIBLE W/C 081 RHR


4 Standard Hinge STSCB1391 114 x 101 NRP 32D 32D1 Privacy Set L9040 07B 630 RHR 6301 Overhead Door Stop 905S C32D C32D1 Kick Plate GSH 80A C32D (200 x 912) RCTM C32D

Heading #028

1 Single door 082A, UNIVERSAL CHANGE ROOM 077 FROM SHOWER 082 O/H

Type: D10, 1200 x 2400 x __ - AL DR x - FR

DOOR DELETED

Heading #029

1 Single door 082B, POOL HALL 072 FROM SHOWER 082 O/H

Type: D10, 1550 x 3200 x __ - AL DR x - FR

OVERHEAD DOOR

COMPELTE BY DOOR SUPPLIER

29 of 75

/10/17




Heading #030

1 Single door 083, NEW VESTIBULE EXIT 083 FROM POOL HALL 072 LHR


1 Continuous Hinge SL11 CL HD x 26251 Exit Device 98EO C32D x 98ALK - LHR C32D1 Cylinder Cyl. Schlage Everest B123 Keyed to Exist. MK System1 Mortise Cylinder 80-132 6261 Surface Closer 4050 REG AL AL1 Mounting Plate 4050-18TJ AL AL1 Floor Door Stop GSH 209 C26D C26D1 Door Contact 1078-1 BRN BRN

NOTE:ALARM KIT BUILT INTO EXIT DEVICE.

Heading #031

1 Single door 083B, EXTERIOR FROM NEW VESTIBULE EXIT 083 LHR

Type: D3A/F04, 1048 x 2660 x 45 - WD DR x HM FR

1 Continuous Hinge SL11 CL HD x 26251 Exit Device 98EO C32D LHR 1048 x 2660 Door C32D1 Surface Closer 4050 TJ AL AL1 Drop Plate 4050-18G AL AL1 Overhead Door Stop 905S C32D C32D1 Threshold CT-45 x 10001 Door Sweep W-24S-CA x 1000 CA1 Door Contact 1078-1 BRN BRN

BALANCE OF WEATHER SEAL BY DOOR SUPPLIER

30 of 75

/10/17




Heading #032

1 Single door ST-A1, STAIR A1 FROM POOL HALL 072 RHR

Type: D3, 1000 x 2350 x 45 - HM DR x HM FR - 45 MIN

4 Standard Hinge STSCB1399 114 X 101 NRP 32D 32D2 Cylinder Cyl. Schlage Everest B123 Keyed to Exist. MK System1 Rim Cylinder 80-159 6261 Mortise Cylinder 80-132 6261 Exit Device 98L-F C32D 996L-NL ALK C26D #07 Lever - RHR C26D/C32D1 Surface Closer 4050 REG AL AL1 Kick Plate GSH 80A C32D (200 X 965) RC TM C32D1 Wall Door Stop GSH 240B C32D C32D1 Door Sweep W-24S-CA x 900 CA1 Door Contact 1078-1 BRN BRN

NOTE:ALARM KIT BUILT INTO EXIT DEVICE.

Heading #033

1 Single door ST-A1B, EXTERIOR FROM STAIR A1 RHR

Type: D1, 1000 x 2350 x 45 - HM DR x HM FR

4 Standard Hinge STSCB1391 114 x 101 NRP 32D 32D1 Exit Device 98EO C32D RHR 1000 x 2350 Door C32D1 Surface Closer 4050 S CUSH AL AL1 Kick Plate GSH 80A C32D (200 X 965) RC TM C32D1 Threshold CT-45 x 9001 Weatherstripping W-20S-CA 1 x 900 + 2 x 2350 CA1 Door Sweep W-24S-CA x 900 CA1 Door Contact 1078-1 BRN BRN

31 of 75

/10/17




Heading #034

1 Single door 160A, CORRIDOR 160 FROM MECHANICAL LHR

Type: D2A/F03, 1000 x 2250 x 45 - HM DR x HM FR

4 Standard Hinge STSCB1399 114 X 101 NRP 32D 32D1 Lockset L9080HD 07B 630 LHR 6301 Cylinder Cyl. Schlage Everest B123 Keyed to Exist. MK System1 Surface Closer 1450 S CUSH AL AL1 Wall Door Stop GSH 240B C32D C32D1 Threshold CT-45 x 10001 Door Sweep W-24S-CA x 1000 CA1 Weatherstripping W-20S-CA 1 x 1000 + 2 x 2350 CA1 Door Contact 1078-1 BRN BRN

Heading #035

1 Single door 160B, MECHANCIAL TO GREEN ROOF RH


4 Standard Hinge STSCB1399 114 X 101 NRP 32D 32D1 Lockset L9080HD 07B 630 RH 6301 Cylinder Cyl. Schlage Everest B123 Keyed to Exist. MK System1 Surface Closer 4050 S CUSH AL AL1 Threshold CT-45 x 1000

Heading #036

1 Single door 161, CORRIDOR 160 TO ELECTRICAL 161 RH

Type: D2A/F03, 1000 x 2250 x 45 - HM DR x HM FR - 45 MIN

4 Standard Hinge STSCB1399 114 X 101 NRP 32D 32D1 Lockset L9080HD 07B 630 RH 6301 Cylinder Cyl. Schlage Everest B123 Keyed to Exist. MK System1 Surface Closer 1450 Rw/PA AL AL1 Kick Plate GSH 80A C32D (200 X 965) RC TM C32D1 Wall Door Stop GSH 240B C32D C32D

32 of 75

/10/17




Heading #037

1 Single door 162, CORRIDOR 160 FROM OFFICE 162 LHR

Type: D2A/F05, 1000 x 2250 x 45 - WD DR x AL FR

3 Standard Hinge STSCB1391 114 x 101 NRP 32D 32D1 Lockset L9070HD 07B 630 LHR 6301 Cylinder Cyl. Schlage Everest B123 Keyed to Exist. MK System1 Surface Closer 4050 TJ DEL AL AL1 Kick Plate GSH 80A C32D (200 X 965) RC TM C32D1 Wall Door Stop GSH 240B C32D C32D

Heading #038

1 Single door 163, OFFICE 162 TO LAN ROOM 163 LH


4 Standard Hinge STSCB1399 114 X 101 NRP 32D 32D1 Lockset L9080HD 07B 630 LH 6301 Cylinder Cyl. Schlage Everest B123 Keyed to Exist. MK System1 Wall Door Stop GSH 240B C32D C32D1 Door Contact 1078-1 BRN BRN

Heading #039

1 Single door 164, CORRIDOR 160 FROM MULTI-PURPOSE 164 LHR



33 of 75

/10/17




Heading #039A

1 Single door 164A, MULTI-PURPOSE 164 FROM STORAGE 164A RHR


3 Standard Hinge STSCB1391 114 x 101 NRP 32D 32D1 Lockset L9070HD 07B 630 RHR 6301 Cylinder Cyl. Schlage Everest B123 Keyed to Exist. MK System1 Wall Door Stop GSH 240B C32D C32D

Heading #039B

1 Single door 165, 2ND FLOOR CORRIDOR 160 TO UNISEX WC 165 RH

Type: D2A/F3, 1000 x 2250 x 45 - WD DR x WD FR

4 Standard Hinge STSCB1391 114 x 101 NRP 32D 32D1 Privacy Set L9040 07B 630 RH 6301 Kick Plate GSH 80A C32D (200 X 965) RC TM C32D1 Wall Door Stop GSH 240B C32D C32D

Heading #040

1 Pair of doors 165A, MULTI-PURPOSE 164 FROM STORAGE 165 LHR/RHRA

Type: D2A/F04, 900, 900 x 2250 x 45 - HM DR x HM FR

DOOR DELETED

Heading #041

1 Pair of doors 165B, MULTI-PURPOSE 166 FROM STORAGE 163 LHR/RHRA

Type: D2B/F04, 900, 900 x 2350 x 45 - WD DR x HM FR

DOOR DELETED

34 of 75

/10/17




Heading #042

1 Single door 166A, CORRIDOR 160 FROM MULTI-PURPOSE 166 LHR



Heading #043

1 Single door 166B, CORRIDOR 160 FROM MULTI-PURPOSE 166 LHR



Heading #044

1 Pair of doors 167A, MULTI-PURPOSE 166 FROM STORAGE 167 LHR/RHRA

Type: D2B/F04, 900, 900 x 2250 x 45 - HM DR x HM FR

8 Standard Hinge STSCB1391 114 x 101 NRP 32D 32D1 Lockset L9070HD 07B 630 RHR 6301 Cylinder Cyl. Schlage Everest B123 Keyed to Exist. MK System1 Surface Bolt GSH 72 x 24" C26D C26D2 Overhead Door Stop 454S C32D (90 Deg.) C32D

35 of 75

/10/17




Heading #045

1 Single door 168, CORRIDOR 160 TO ACCESSIBLE W/C 168 RH


4 Standard Hinge STSCB1391 114 x 101 NRP 32D 32D1 Privacy Set L9040 07B 630 RH 6301 Kick Plate GSH 80A C32D (200 X 965) RC TM C32D1 Wall Door Stop GSH 240B C32D C32D

Heading #046

1 Single door 168A

1 x __ x __ - - DR x - FR

DELETE - RESERVE HEADING FOR FUTURE USE

Heading #047

1 Single door ST-A2, STAIR A2 FROM CORRIDOR 160 LHR


4 Standard Hinge STSCB1399 114 X 101 NRP 32D 32D1 Exit Device 98-L-NL-F C26D 996L-NL-R C26D LHR #07 Lever 900 x 2250 Door C26D/C26D1 Rim Cylinder 80-159 6261 Cylinder Cyl. Schlage Everest B123 Keyed to Exist. MK System1 Surface Closer 4050 REG AL AL1 Kick Plate GSH 80A C32D (200 X 876) RC TM C32D1 Wall Door Stop GSH 240B C32D C32D1 Weatherstripping W-22-BL x 5600 BL1 Door Contact 1078-1 BRN BRN

36 of 75


Architectural Drawings ADD2

3a. LANDSCAPE DRAWING REVISIONS + CLARIFICATIONS

Drawing L100-A LANDSCAPE REMOVALS PLAN - A.1

a) ADD the following note to the drawing legend: Where sub—base is to be retained under the removal of paving contractor shall verify depth of sub-base materials to comply with details 6, 7, & 8/L500. (No sketch issued)

b) ADD the following note to the drawing legend: Existing pedestrian concrete to remain damaged by construction activities to be repaired or replaced in kind. (No sketch issued)

c) ADD the following note to the drawing legend: Removals plan to be read in conjunction with L101A & B. (No sketch issued)

d) DELETE duplicate note.REFER TO ADD2-010

Drawing L100-B LANDSCAPE REMOVALS PLAN - B.1

a) Refer comments .1 & .2 above.

b) ADD hatch and note.REFER TO ADD2-010

Drawing L101-A LAYOUT AND MATERIALS PLAN – A & Drawing L101-B LAYOUT AND MATERIALS PLAN

.1 L101-A, L101-B

a) ADD notes.REFER TO ADD2-011

Drawing L102-B GRADING PLAN – B .1

a) REVISE hatch to show existing concrete.b) ADD markers showing where new meets existing.c) DELETE marker showing where new meets existing.REFER TO ADD2-012

Drawing L500 LANDSCAPE DETAILS .8/L500

a) ADD new detail on existing sheet.REFER TO ADD2-0113

37 of 75



3b. ARCHITECTURAL DRAWING REVISIONS + CLARIFICATIONS

Drawing A002– SITE PLAN.1 4/A002

a) REVISE note to indicate existing sidewalk to be removed and replacedREFER TO ADD2-014

Drawing A102– GROUND FLOOR PLAN.1 1/A102

a) DELETE elevation tag reference to 1/zA325NO SKETCH ISSUE

Drawing A103– SECOND FLOOR PLAN.1 1/A103

a) DELETE elevation tag reference to 1/zA325NO SKETCH ISSUE

Drawing A104– ROOF PLAN.1 1/A104

a) DELETE elevation tag reference to 1/zA325b) DELETE elevation tag reference to 1/CofA-A010c) DELETE elevation tag reference to C1Fa_8.5x11_A010d) REVISE south scupper width to 400e) REVISE north scupper location and width to 400f) ADD reference tag 6/A323 north of GL-12y across GL-HNO SKETCH ISSUE FOR ITEMS a) b) and c) above

REFER TO ADD2-009 FOR ITEMS d) e) and f) above

Drawing A111– RCP BASEMENT & GROUND FLOOR, DEMO RCP GROUND FLOOR.1 5/A111

a) ADD furring type F1 at north and south wall of Entry Rm 060.b) REVISE slot for OH coiling door as indicated and dimensionedc) ADD reference to 3/A113 as indicatedd) ADD dimension to locate speaker

38 of 75



e) REVISE dimension b/w diffuser and light fixture as notedf) REVISE dimension for wood ceiling to “EQ” at both ends in Entry Rm 060g) ADD note regarding wall finish to extent above ceilingh) REVISE further as indicatedREFER TO ADD2-001

Drawing A401– CHANGE ROOMS - LOCKERS AND CHANGE STALLS.1 1/A401

a) ADD furring type F1 at north and south wall of Entry Rm 060.b) REVISE partition type from P3 to PG2T near door # 061Bc) ADD plan detail 8/A406d) REVISE dimensions as notede) REVISE further as indicatedREFER TO ADD2-002

Drawing A402– CHANGE ROOMS – UNIVERSAL WC AND ACCESSIBLE WC.1 10/A402

a) DELETE reference tag 10/A412 for clarityNO SKETCH ISSUE

Drawing A406 – ADMIN AREAREFER TO RE-ISSSUED SHEET A406.1 1/A406 and 2/A406

a) ADD note and dimension for furring partition to extent above ceilingb) ADD dash line to indicate door frame beyond for clarityc) REVISE “TL-10 BEHIND GLASS DOOR” to “BACK PAINTED GLASS BEHIND GLASS

DOOR”

d) ADD vertical dimension of clear opening for clarity.2 3/A406

a) ADD furring type F1 at north and south wall of Entry Rm 060.b) ADD note “TILE FINISH ON” above furring tag “F1” at north and south wall of Entry Rm

060.

c) ADD “ON RETURN” below finish tag “TL-15”d) REVISE “SSF-1” extent above opening as noted

.3 4/406

39 of 75



a) ADD furring type F1 at north and south wall of Entry Rm 060 w/ note “TILE FINISH ON” above furring tag

b) ADD note for furring partition to extent above ceilingc) ADD note “SIMILAR SSF LAYOUT ON EITHER SIDE AND ABOVE ON WEST SIDE

OF DOOR”

.4 5/A406

a) DELETE notes (2) “WALL EXPANSION JOINT COVER”b) REVISE floor expansion joint as indicatedc) REVISE note “25mm EXPANSION JOINT” to ”EXPANSION JOINT IN TILE” d) DELETE note “REMOVEABLE TACKBOARD”e) ADD arrow from “TYPICAL REMOVABLE SOLID SURFACE” pointing to the middle

panel

f) REVISE notes (2) “TILE FINISH” to “BACK PAINTED GLASS ON 13mm EXTERIOR GRADE PLYWOOD”

g) REVISE further as noted.5 6/A406

a) DELETE expansion joint coverb) REVISE note “TILE TO TILE FLOOR EXPANSION JOINT” to “EXPANSION JOINT IN

TILE”

.6 8/A406

a) ADD new detail 8/A406.7 9/A406

a) ADD new detail 9/A406

Drawing A410– POOL HALL PARTIAL PLANS & SECTIONS.1 1/A410

a) ADD door number 072Bb) REVISE glass door to a single doorREFER TO ADD2-007

Drawing A450 – INTERIOR DETAILS.1 5/A450

c) REVISE partition type from “P3” to “PG2T”d) ADD fire proofing around columne) ADD align note b/w tile and face of door framef) ADD “SSF-1” finish east of “PG2T” partition and jamb returng) ADD blocking for door frames

40 of 75



h) ADD furring partition type “F1” beside door framei) REVISE further as notedREFER TO ADD2-003

.2 9/A450

a) DELETE note “RATED VERTICAL EXPANSION JOINT?”b) DELETE note “CONTINUE RATED TILE BACKER BOARD FOR COLUMN

PROTECTION”

c) ADD fire proofing around column and note “FIRE RATED COL”d) REVISE note “ALU COVER JOINT W/ RUBBER INSERT. COLOUR TO MATCH WALL”

to “TILE JOINT AT TRANSITION B/W NEW AND EXISTING CONCRETE STRUCTURE. EXPANSION JOINT IN TILE”

e) REVISE note “EXPANSION JOINT COLOUR TO MATCH FLOOR FINISH” to “EXPANSION JOINT IN FLOOR TILE”

f) REVISE detail over expansion joint as indicatedREFER TO ADD2-004

.3 15/A450

a) REVISE note “EXPANSION JOINT” to “EXPANSION JOINT IN TILE IN FLOOR AND WALL”

b) REVISE EXPANSION JOINT AS INDICATEc) REVISE further as indicatedREFER TO ADD2-005

.4 16/A450

a) REVISE note “EXPANSION JOINT” to “EXPANSION JOINT IN TILE IN FLOOR AND WALL”

b) REVISE EXPANSION JOINT AS INDICATE

c) REVISE further as indicatedREFER TO ADD2-006

Drawing A451 – INTERIOR DETAILS.1 1/A451

a) ADD alignment lines between east and west side of guard.b) ADD note “GAPS TO ALIGN ON BOTH SIDES”c) REVISE dimensions from “4 EQ. PANELS W/ 50mm GAP” to “4 EQ. PANELS W/ GAPS

AS INDICATED”

d) ADD note “EXPANSION JOINT IN TILE” at south end of bridgee) REVISE dimension for bridge as indicatedf) ADD notes (2) “ALIGN INTERIOR FACE OF STEEL GUARD WITH WALL FINISH”

41 of 75



g) DELETE notes (2) “WORKING PLANE INSIDE FACE OF STEEL GUARD”h) ADD note “EXPANSION JOINT W/ COVER” at north end of bridgei) REVISE further as indicated.REFER TO ADD2-018

.2 2/A451

a) REVISE drawing as indicatedREFER TO ADD2-019

.3 3/A451

a) ADD dimensions as noted.REFER TO ADD2-020

.4 4/A451

a) REVISE note “EXPANSION JOINT” to “EXPANSION JOINT IN TILE” at ceilingb) ADD note “EXPANSION JOINT W/ COVER”

REFER TO ADD2-021

Drawing A600 – STAIRREFER TO RE-ISSSUED SHEET A600.1 1/A600

a) REVISE dimensions.b) ADD new section detail reference.

.2 2/A600

a) REVISE stair guard.b) REVISE stair riser height.c) REVISE riser breakdown and landing height.d) ADD guard height dimensions.

.3 3/A600

a) REVISE landing and stair set out dimensions.b) ADD new section detail and reference.c) ADD dimensions.

.4 4/A600

a) ADD new section detail and reference.b) ADD door reference ST-A1B.c) ADD dimensions.d) REVISE integral dome reference.

.5 5/A600

42 of 75



a) ADD new section detail and reference.b) ADD dimensions.c) REVISE landing height.d) REVISE dimensions.

.6 5b/A600

a) ADD new section 5b/A600..7 6/A600

a) ADD dimensions.b) REVISE expansion joint note.c) REVISE dimensions.

.8 6/A600

a) ADD dimensions.b) REVISE dimensions.c) DELETE nosing at steel pan stair.d) ADD new detail and reference 9/A902.e) ADD new detail and reference 19/A600.f) CLARIFICATION: Spray applied AB cross referenced to spec as INS-28 with thermal

barrier (as noted in ADD1 issued February 10 2017)

.8 10/A600a) ADD note regarding picket spacing.b) ADD note regarding guard construction.c) ADD dimension.d) REVISE steel support location.e) CLARIFICATION dashed line of stringer beyond.

.9 11/A600

f) ADD note: contractor to coordinate door header location w/ stair landing..10 13/A600

a) ADD handrail supports.b) ADD dimensions.c) ADD new detail and reference 7/A902.d) CLARIFICATION note describing handrail as SST-POWDER added.

.11 15/A600

a) ADD south handrail.b) ADD dimensions.c) REVISE dimensions

43 of 75



d) REVISE detail reference for detectable warning surface.e) DELETE reference to expansion joint.

.12 16/A600

a) ADD new detail and reference 19/A600.b) ADD dimensions.c) REVISE handrail.d) REVISE dimensions.e) CLARIFICATION finish outline shifted to align with stair.

.13 17/A600

a) ADD reinforcement to concrete masonry units as required to support ladder..14 16/A600

a) ADD new detail and reference 19/A600..15 19/A600

a) ADD new detail 19/A600..16 20/A600

a) ADD new detail 20/A600.

Drawing A701– EXTERIOR AND INTERIOR SCREEN .1 31/A701

a) REVISE as indicatedREFER TO ADD2-007

.2 GLASS AND FRAME TYPES

a) ADD notes 7,8 and 9 as indicated to “GENERAL NOTES:”b) ADD note 4 as indicated to “CURTAIN WALL NOTES:”REFER TO ADD2-008

Drawing A801 – DOOR SCHEDULE & DETAILSREFER TO RE-ISSSUED SHEET A406.1 DOOR SCHEDULE

a) REVISE as indicated.2 1/A801

a) REVISE note “PREFINISHED ALUM CLOSER BY GLAZING CONTRACTOR SHIM AS REQ’D” to “PREFINISHED ALUM CLOSER ON BOTH SIDES BY GLAZING CONTRACTOR BLOCKING AS REQ'D”

b) ADD notes (2) “ALIGN” on both side of door frame.c) REVISE further as noted

44 of 75



Drawing A902 – FINISH SCHEDULE, RB SCHEDULE & TYP. FLOOR FINISH DETAILS.1 7/A902

a) ADD new section detail 7/A902.REFER TO ADD2-015

.2 8/A902


.3 9/A902


END OF ARCHITECTURAL DRAWING REVISIONS + CLARIFICATIONS.

45 of 75

N

Q

13x

P7

A406

3

A350 13y

OS

sp

av

152

305 2440 305

152

550

1105

750

216

EQ. EQ.

SLOT FOR OH

COILING DOOR

SPRINKLER IN BLANK OFF

PANEL. SEE CHANGER OOM

CLG FOR DETAIL

2440

os

64 25

114

25

EQ

EQ

3 ADD2

3 A113

Sim

3 A113

Sim

3 A113

Sim

WALL FINISH TO EXTENT

ABOVE CEILING HEIGHT.

TYP

3 ADD2

F1

F1

/REF 5 A111

3 ADD2

Scale:

Drawn By:

Project No: Drawing No:

2/15/2017 8:34:14 AM

1 : 50

WELLESLEY COMMUNITY CENTER

1311

AuthorADD2-001

ADDENDUM 2

1 : 50

ENTRY / RECEPTION CEILING - ADD2

REV. DESCRIPTION DATE

3 ADDENDUM 2 02 15 2017

46 of 75

13

H

N

Q

A406

4

21

3

ENTRY

060

F1C

FD1

P060B

5

A406

410

3609

7

A406

3

A350

P3P3

1

A501

13y

5

A450

PG2T

FEC

F1C

PG2T

3211

061B

12

A501PG2TPG2T

8

A406

1200

683

F1

FL-2A

F1

3 ADD2

/REF 1 A401

Scale:

Drawn By:


2/15/2017 8:34:39 AM

1 : 50


1311

AuthorADD2-002

ADDENDUM 2

1 : 50

PARTIAL OF CHANGE ROOM - ADD2


3 ADDENDUM 2 02 15 2017

47 of 75

Q

P

13y

FIRE PROOFED

COL

GLAZED SLIDING ALUM

DOOR

REFER TO SCHEDULE

REFER TO A406 FOR

ADDITIONAL DETAIL

PG2T

TILE FINISH

TILE FINISH

PROVIDE BLOCKING

AT DOOR FRAME

HM DOOR FRAME

295

SSF-1

TILE FINISH

F1

SSF-1

ALIGN

PG2T

CAULKING B/W FINISH

AND DOOR FRAME

/REF 5 A450

Scale:

Drawn By:


2/15/2017 8:34:57 AM

1 : 10


1311

AuthorADD2-003

ADDENDUM 2

1 : 10

PLAN DETAIL - RATED COLUMN @ 13y & Q - ADD2


2 ADDENDUM 1 02 10 2017

48 of 75

H

N

10y9y

800

150

TILE FINISH

LARGE FORMAT PORCELAIN TILE

F1C

F1C

F1C

CORNER METAL TRIM

LARGE FORMAT PORCELAIN TILECORNER METAL

TRIM

VERIFY DIMENSIONS &

LOCATIONS OF EXISTING

STRUCTURE ON SITEEXIST.LOBBY002

EXPANSION JOINT

IN FLOOR TILETILE JOINT AT TRANSITION B/W NEW AND EXISTING

CONCRETE STRUCTURE. EXPANSION JOINT IN TILE

550

74

287

PROVIDE BLOCKING AS

REQ'D FOR GRAB BAR

FIRE RATED COL

3 ADD2

/REF 9 A450

3 ADD2

Scale:

Drawn By:


NORTH ARROW

2/15/2017 8:35:21 AM

1 : 10

1311

AuthorADD2-004


ADDENDUM 2

1 : 10

GROUND FLOOR PLAN DETAIL @ GL-H/10y - ADD2


3 ADDENDUM 2 02 15 2017

49 of 75

15

H

N

15y15x

470 817 745

Sc-064a

EXIST. ATHLETIC CORRIDOR

031

UNIVERSAL CHANGE ROOM B

064

1000 518 9

12mm LAMINATED GLASS W/

COLOURED INTERLAYER ON

19mm PLY ON

STUDS

LARGE FORMAT TILE FINISH

EXPANSION JOINT IN TILE IN

FLOOR AND WALL

TILE TO MATCH FLOOR TILE IN

CHANGE ROOM

TL

TL

TILE TRANSITION

REFER TO FINISH PLAN FOR TILE

TYPE

29

A701

30

A70128

A701

3 ADD2

/REF 15 A450

Scale:

Drawn By:


NORTH ARROW

2/15/2017 8:35:40 AM

1 : 10

1311

AuthorADD2-005


ADDENDUM 2

1 : 10

PLAN DETAIL SC-064A - ADD2


3 ADDENDUM 2 02 15 2017

50 of 75

11

H

N

11x 11y2 A351



19mm PLY ON

STUDS

LARGE FORMAT TILE FINISH

Sc-077a

EXIST. ATHLETIC CORRIDOR

031

28

A701

30

A701

EXPANSION JOINT IN TILE IN

FLOOR AND WALL

TILE TO MATCH FLOOR TILE IN

CHANGE ROOM

TL

TL

TILE TRANSITION

REFER TO FINISH PLAN FOR TILE

TYPE



19mm PLY ON

STUDS

3 ADD2

Scale:

Drawn By:


NORTH ARROW

2/15/2017 8:36:04 AM

1 : 10

1311

AuthorADD2-006


ADDENDUM 2REV. DESCRIPTION DATE

3 ADDENDUM 2 02 15 2017

1 : 10

PLAN DETAIL SC-077a - ADD2

51 of 75

X

16z

STAIR

B

TDA701

31

GLASS DOOR

F1C

FEC

TH

15 A402

Sim

3 ADD2

/REF 1 A410

072B

LEVEL 1 (+110.95)

+0

Pool Platform

+2660

13

A600

SS HINGES W/ HOLD

OPEN AT 90 DEG

SS KEYED LOCK TO

RELEASE LATCH.

1000

GL-7

200

SS WALL MOUNTED

LATCH CATCHER

TILE FINISH ON CMU

REFER TO HARDWARE SCHEDULE.

GC TO COORD WITH GLASS AND

HARDWARE SUPPLIER

FINAL WIDTH OF

GLASS TBC ON SITE

1800

3 ADD2

/REF 31 A701

Scale:

Drawn By:


SEAL

2/15/2017 8:36:48 AM

1 : 50

1311

AuthorADD2-007


ADDENDUM 2

1 : 50

LEVEL 1 - POOL HALL - ADD2

1 : 50

POOL STAIR DOOR ELEVATION - ADD2


3 ADDENDUM 2 02 15 2017

52 of 75

GLASS TYPES:

GL3 POOL LOWER: INSULATED GLASS UNIT - CLEAR - FRIT

OUTER LITE: 8MM CLEAR TEMPERED GLASS

CERAMIC FRIT PATTERN - 5MM DIA. DOTS @ 100MM O.C ON SURFACE 2

LOW E COATING ON SURFACE 3

13MM THERMAL SPACER BAR

INNER LITE: 10MM (2x5MM) CLEAR TEMPERED LAMINATED GLASS W/

CLEAR INTERLAYER

GL1 POOL UPPER AND MULTI PURPOSE BLOCK: INSULATED GLASS UNIT - CLEAR - FRIT

OUTER LITE: 6MM CLEAR HEAT STRENGTHENED GLASS




INNER LITE: 6MM CLEAR HEAT STRENGTHENED GLASS

GL2 POOL UPPER (CLERESTORY): INSULATED GLASS UNIT - CLEAR - FRIT





INNER LITE: 12MM (2x6MM) CLEAR HEAT STRENGTHENED LAMINATED GLASS W/

CLEAR INTERLAYER

GL6 RESERVED

GL7 INTERIOR SCREENS (POOL): 12MM (2x6MM) CLEAR TEMPERED LAMINATED GLASS W/

CLEAR INTERLAYER TYPICAL

GL8 GLASS BALUSTRADE: 16MM (8MM+8MM) CLEAR HEAT STRENGTHENED LAMINATED GLASS W/

CLEAR INTERLAYER

FRAME TYPES:

EXTERIOR GLAZING

CW1 CURTAIN WALL, HIGH SPAN

63.5mm X 203mm PTD ALUM BACK SECTIONS

4 SIDED SSG (INCLUDES NO PERIMETER CAPS)

GLASS: VARIES (REF. A200 SERIES BUILDING ELEVATIONS)

CW2 CURTAIN WALL, LOW SPAN

63.5mm X 133mm PTD ALUM BACK SECTIONS

4 SIDED SSG (INCLUDES NO PERIMETER CAPS)

GLASS: VARIES (REF. A200 SERIES BUILDING ELEVATIONS)

SL-1 42mm ALUM. CHANNEL FRAMING (TOP & BOTTOM)

GL4 POOL LOWER: INSULATED GLASS UNIT - CLEAR - FRIT





INNER LITE: 6MM CLEAR TEMPERED GLASS

GL7a INTERIOR SCREENS (POOL): 12MM (2x6MM) CLEAR TEMPERED LAMINATED GLASS W/

TRANSLUCENT INTERLAYER TO DESK HEIGHT

GL5 INTERIOR SCREENS (STEAM ROOM): INSULATED GLASS UNIT - CLEAR - NO FRIT

OUTER LITE: 6MM (3MM+3MM) CLEAR TEMPERED LAMINATED GLASS W/

CLEAR INTERLAYER


INNER LITE: 6MM (3MM+3MM) CLEAR TEMPERED LAMINATED GLASS W/

CLEAR INTERLAYER

GL9 INTERIOR SCREENS: 12MM CLEAR TEMPERED GLASS

AL-1 THERMALLY BROKEN ALUM CHANNEL FRAME FOR IGU. (TOP & BOTTOM)

GENERAL NOTES:

1. SCREEN SYSTEM TYPES ARE NOTED ON SCHEDULE. REFER TO PROJECT MANUAL.

2. SCHEDULE INDICATES MINIMUM GLASS THICKNESSES, INCREASE GLASS THICKNESS TO MEET

ALL APPLICABLE CODES AND SAFTY STRENGTH AND DEFLECTION REQUIREMENTS FOR LOAD AND SIZE

BASED ON ASTM E 1300.

3. ALL EXTERIOR IGU IS TO HAVE 5MM DIA CERAMIC FRIT PATTERN @ 100 X 100mm O.C.

TO MEET TORONTO GREEN STANDARDS FOR MIGRATORY BIRDS TYP.

4. PROVIDE CONTINUOUS STEEL SUPPORTS AND BRACING BACK TO PRIMARY STRUCTURE AS NECESSARY-

CONCEALED ABOVE CEILING AND ACROSS HEAD OF ALL FULL HEIGHT GLASS PARTITION: TO BE DESIGNED

UNDER DIRECT SUPERVISION OF REGISTERED PROFESSIONAL STRUCTURAL ENGINEERS,

BRACES AT SCREENS REQUIRED TO ACT AS GUARDS SHOULD BE DESIGNED ACCORDINGLY

TO MEET REQUIREMENTS.

5. SITE VERIFY ALL GLAZED OPENING DIMENSIONS.

6. INTERMEDIATE DIMENSIONS ARE GENERALLY TO THE CENTERLINE OF THE FRAME.

7. REFER TO DOOR SCHEDULE FOR DOOR TYPES.

8. REFER TO JAMB SCHEDULE FOR JAMB TYPES.

9. FOR MIRRORS AND BACKPAINTED GLASS: COORDINATE OPENINGS REQUIRED FOR WALL MOUNTED FIXTURES,

ACCESSORIES AND RECEPTACLES AS REQUIRED.

CW3 RESERVED

CLEAR GLASS, ALL TYPES SHADOW BOXsb CLOSURE PANELcp

SF-1

SF-2

45 x115mm INTERIOR ALUM. STOREFRONT FRAME FOR SINGLE GLASS,

PAINTED ALUM. BACK SECTIONS.

50 x115mm INTERIOR ALUM. THERMALLY BROKEN STOREFRONT FRAME FOR IGU,

PAINTED ALUM.BACK SECTION.

GL8a INTERIOR SCREENS: 12MM (2x6MM) CLEAR TEMPERED LAMINATED GLASS W/

COLORED INTERLAYER

Determine if existing mulllion profile could be used

CURTAIN WALL NOTES:

1. ALL ALUMINUM SCREENS IN OR OPENING INTO AQUATIC HALL AND CHANGE ROOMS

TO HAVE FASTENERS AND STEEL COMPONENTS ALL TO BE STAINLESS STEEL.

2. DIMENSIONS INDICATED ARE NOMINAL. ALL DIMENSIONS TO BE SITE VERIFIED.

3. SEE PROJECT MANUALL FOR GLAZED ALUMINUM DOORS.

4. ALL FRAMES TO RECEIVE DURANAR XL PAINTED FINISH UNLESS OTHERWISE NOTED.

SF-3 50x115 ALUM. PHANTOM DOOR FRAME FOR LAMINATED GLASS,

PAINTED ALUM.BACK SECTION.

GL8b GLASS BALUSTRADE: 16MM (8MM+8MM) CLEAR HEAT STRENGTHENED LAMINATED GLASS W/

COLORED INTERLAYER

3

3

Scale:

Drawn By:


NORTH ARROW

1 : 20

2/15/2017 2:39:33 PM

1311

AuthorADD2-008


ADDENDUM 2

1 : 20

GLASS AND FRAME TYPES ADD2


53 of 75

E/A3000CFM

+100

RD

11

H

N

Q

11y

SLO

PE

D S

TRU

CTU

RE

CFD

A201 4

4.1

%

R

P

2%

120.75 m

5

120.13 m

SCUPPER5

A323

3460

400

CROSS HATCHED AREA DENOTES

LOCATION WHERE FASTENING RATE

NEED TO BE INCREASED AT CORNERS.

SEE SPEC FOR DIMENSIONS AND FM

GLOBAL DATA SHEET 1-29.

TYP FOR R1 ROOF

3 ADD2

18

N

Q

17z17x

R

P

17y

2.3

%

120.75 m

120.75 m

1500

SCUPPER

100

400

3 ADD2

12 13

G

H

N

Q

12y1

A301

1

A301

A210

3

CFD

P

13y

5

A310

6

A323

3 ADD2

Scale:

Drawn By:


NORTH ARROW

2/15/2017 2:40:02 PM

1 : 100

1311

AuthorADD2-009


ADDENDUM 2

1 : 100

Partial Roof Plan - ADD2a

1 : 100

Partial Roof Plan - ADD2b

1 : 100

Partial Roof Plan - ADD2c


3 ADDENDUM 2 02 15 2017

54 of 75

55 of 75

56 of 75

57 of 75

58 of 75

20 500

22 400

200

161

300 STORM20 500

22 400

200

161

300 STORM20 500

22 400

200

161

300 STORM

111.4

3

111.2

0

111.0

1

MH

110.6

5

110.7

8110.8

0

110.7

7

110.4

7

110.6

2

110.7

6

C

110.7

5

110.5

0

110.7

8

111.1

2

111.3

7

111.1

8

110.9

8

110.8

2

110.6

2

111.1

9

111.2

5

111.1

8

111.2

0

111.3

4

111.3

3111.3

8

111.3

7

110.4

5

110.5

0

110.7

3

111.0

3

111.2

7

111.4

8

111.3

6

111.5

3

111.7

2

111.3

2 111.3

0

111.5

7

111.7

9111.5

3

111.7

9

110.7

0

110.8

8

CB

MH

111.1

1

111.3

4

111.3

9

111.4

3

110.6

2

110.8

8

111.1

1

111.3

8

111.6

3

0.15 ∅ 0.20 ∅

0.10 ∅

0.40 ∅

0.20 ∅

0.30 ∅

0.90 ∅

0.10 ∅

0.15 ∅

EXIST. RETAINING

WALL TO BE REMOVED

EXISTING

WHEEL TRANS

STOP

EXISTING SOD

EXIST. CONC

TO BE REMOVED & REPLACED

PROPERTY LINE

DASHED LINE OF EXIST. BIKE RENTAL

STATIONS TO BE RELOCATED

EXIST ARMOUR STONE &

LOG BENCHES TO BE REMOVED &

RELOCATED

EXIST. ENTRANCE SIGNAGE

TO BE RELOCATED

3268

DASHED LINE OF TREE

PROTECTION

REFER TO ARBORIST REPORT

PROPOSED LOCATION

OF EXIST. ENTRANCE

SIGNAGE

PROPOSED LOCATION OF

6 EXISTING BIKE RACKS

(12 SPACES)

DASHED LINE OF

EXISTING STAIRS TO

BE CUT BACK &

REMOVED

PROPOSED LOCATION OF

EXISTING BIKE RENTAL STATION

500017756

DASHED LINE OF TREE

PROTECTION

REFER TO ARBORIST REPORT

5000

TY

P

1650

TO BE REMOVED & REPLACED

EXISTING SIDEWALK

3 ADD2

/REF 4 A002

Scale:

Drawn By:


NORTH ARROW

2/15/2017 2:46:38 PM

1 : 200

1311

AuthorADD2-014


ADDENDUM 2

1 : 200

Site Plan (PART) - ADD2


3 ADDENDUM 2 02 15 2017

59 of 75

Pool Platform

+2660

C.I.P

.

ST

RU

CT

UR

AL C

ON

C. S

LA

B

STL HAND RAIL BEYOND

CAST IN PLACE

CONCRETE STAIR

DETECTABLE WARNING SURFACE

TILE W/ INTEGRAL DOMES

CONTRASTING TILE

NOSING

REFER TO PLAN

TREAD

CONTRASTING TILE COLOUR

SCHLUTER TRIM AS PER

SPECIFICATIONS

STRETCHER TILE

3ADD2/REF 7 A902

Scale:

Drawn By:


2/15/2017 2:47:18 PM

1 : 5


1311

AuthorADD2-015

ADDENDUM 2

1 : 5

SECTION DETAIL - TILE NOSING AT POOL HALL STAIR - ADD2


3 ADDENDUM 2 02 15 2017

60 of 75

Level 1 Gym

+600

SAFETY TREAD

INSERT @ EACH

TREAD (TYP.)

STRETCHER TILE

SCHLUTER TRIM

AS PER

SPECIFICATIONS

REFER TO PLAN

TREAD

DETECTABLE

WARNING

SURFACE TILE

3 ADD2

/REF 8 A902

Scale:

Drawn By:


2/15/2017 2:47:47 PM

1 : 5


1311

AuthorADD2-016

ADDENDUM 2

1 : 5

SECTION DETAIL - TILE NOSING AT CHANGE ROOM STAIR - ADD2


3 ADDENDUM 2 02 15 2017

61 of 75

LEVEL 2

+5000

REFER TO PLAN

TREAD

RE

FE

R T

O S

EC

TIO

N

RIS

ER

TREAD

SCHLUTER TRIM AS PER SPECIFICIATIONS

DETECTABLE WARNING SURFACE

TILE FINISH AS PER TILE SCHEDULE

SAFETY STRIP ROUTERED INTO TILE BY

MANUFACTURER

EDGE OF TILE TO BE RADIUSED 6mm BY TILE

MANUFACTURER

TILE FINISH AS PER TILE SCHEDULE

CONCRETE ON STEEL PAN STAIR

INS-28 WITH THERMAL BARRIER

REFER TO WALL SECTION DETAILS

3ADD2

/REF 9 A902

Scale:

Drawn By:


2/15/2017 2:48:05 PM

1 : 5


1311

AuthorADD2-017

ADDENDUM 2

1 : 5

SECTION DETAIL - TILE NOSING AT STAIR 11 -ADD2


3 ADDENDUM 2 02 15 2017

62 of 75

N

Q

P

2

A451

4

A451

800

15

1883

15

15

185

A451

3

4 EQ PANELS W/ GAPS AS INDICATED

4960 TBC ON SITE

122520

122520

122520

1225

25 25

FACE OF WALL FINISH

25 305 25

GA

PS

TO

ALIG

N O

N

BO

TH

SID

ES

ALIGN INTERIOR

FACE OF STEEL

GUARD WITH WALL

FINISH

ALIGN INTERIOR

FACE OF STEEL

GUARD WITH WALL

FINISH

EXPANSION JOINT

W/ COVER

3ADD2

3ADD2

3ADD2

3ADD2

3ADD2

3ADD2

3ADD2

3ADD2

EXPANSION JOINT IN TILE

3ADD2

1

ADD2-019

/REF 1 A451

ADD2-020

1

1

ADD2-021

Scale:

Drawn By:


NORTH ARROW

2/15/2017 2:40:44 PM

1 : 20

1311

AuthorADD2-018


ADDENDUM 2REV. DESCRIPTION DATE

3 ADDENDUM 2 02 15 2017

1 : 20

BRIDGE ENLARGED PLAN - ADD2

63 of

Documents

February 16, 2017 Via E mail (75 pages) Addendum …...Refer to specification section 31 41 00 1.4.2.1 regarding lagging tolerances. Weepers and insulation should be able to be installed