Click here to load reader
Upload
lynhu
View
213
Download
0
Embed Size (px)
Citation preview
Features• Self contained in lockable cabinet
• 24 VDC remote power supply
• Power-limited individually protected outputs
• Two input/control circuits (from FACP notification appli-ance circuits) are electrically isolated from outputs.Input 1 controls Output 1 and Output 2. Input 2 controlsOutput 3 and Output 4
• Two Style Y/Style Z notification appliance circuits (out-puts 1 and 3)
• Two Style Y circuits (outputs 2 and 4 which could beconfigured permanently ON (non-resettable))
• 4.0 amp continuous output
• 6.0 amp full load output
• Suitable for powering 4-wire smoke detectors
• Integral battery charger
• Up to 7.0 AH batteries in FCPS-24 cabinet
• Fully supervised power supply, battery, and notificationappliance circuits
• Earth fault detection (selectable)
• A.C. fail trouble contact reporting immediate, delayed8, or 16 hours (selectable)
• Fixed terminal blocks for field wiring capable of accept-ing up to 12 AWG wire
• Normally closed output trouble contacts
• Suitable for 60 hour standby when outputs are used asnotification circuits
Applications
The FCPS-24 and FCPS-24E are compact, cost effec-tive, remote power supplies with battery chargers. TheFCPS-24(E) consists of a regulated and filtered 24 VDCoutput that may be configured to drive four notificationappliance circuits (four Style Y, or two Style Z and twoStyle Y). Alternately, all outputs could be used as anycombination of resettable/non-resettable power outputs.The FCPS-24(E) also contains a battery charger capableof charging up to 7.0 Amp Hour batteries.
Technical InformationAC Power:
FCPS-24:. . . . . . . . . . . . . . . . . . . 120 VAC, 50/60 HzFCPS-24E:. . . . . . . . . . . . . . 220/240 VAC, 50/60 Hz
Wire Size: . . . Minimum #14 AWG with 600 V insulationBattery:
Normal Charge Voltage: . . . . . . . . . . . . . . . . . 27.6 VMaximum Charge Current:. . . . . . 250 mA MaximumMaximum Battery Capacity: . . . . . . . . . . . . . . 7.0 AH
DIMENSIONS
APPLICATION EXAMPLES
Example 1: Expand notification appliance power an addi-tional 6.0 amps. Use up to 4 Class B (Style Y) outputs or2 Class A (Style Z) and 2 Class B (Style Y) outputs.
In this example, the FACP notification appliance circuitswill activate the FCPS-24 when on (polarity reverses).Trouble conditions on the FCPS-24 are sensed by theFACP through notification appliance circuit #1.
Example 2: Use the FCPS-24 as a 4 amp regulatedpower supply. The output may be selected as resettableor non-resettable.
A resettable FCPS output is created by tying the reset-table output from the FACP to one or both of the FCPS-24 inputs. A non-resettable output is created simply bycutting an on board resistor. For addressable unit appli-cations, use a monitor module to sense the trouble sta-tus of the FCPS-24 via the trouble contacts. Use a FreeInitiating Zone or an Addressable monitor module tomonitor the FCPS for trouble.
DETECTION AND CONTROL EQUIPMENT
DATA SHEET
FCPS-24/FCPS-24EREMOTE POWER SUPPLY
PC2001177
One Stanton StreetMarinette, WI 54143
FACPFCPS-24(E)
NAC #1SILENCEABLE
NAC #2NON-SILENCEABLE
ELRINPUT 1
SILENCEABLEHORNS
NON-SILENCEABLESTROBESINPUT 2
ELR
14.5 IN.(368 mm)
2.75 IN.(70 mm)DEEP
15 IN.(381 mm)
ALL OUTPUTSREGULATED + 24 VDC
RESETTABLE POWER
NON-RESETTABLEPOWER
END OFLINE RELAY
INPUT 1
TROUBLECONTACTS
INPUT 2
•R175 CUT
•R176 CUT
OUTPUT 1
OUTPUT 2
OUTPUT 3
OUTPUT 4
+ 24VRESETTABLEPOWER
SLC LOOP
FACP
MONITORMODULE
Technical Information (Continued)
Example 3: Use addressable control modules to activatethe FCPS-24(E) instead of FACP notification appliancecircuits (compare with example 1). This typically allowsfor mounting the FCPS-24(E) at greater distances awayfrom the FACP while expanding system architecture.
FCPS-24(E) troubles are sensed by control module #1 inOff state. Both control modules should be close nippledto FCPS-24(E) cabinet.
Listings and Approvals*UL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . S635California State Fire Marshal (CSFM) . . 7315-0028:178MEA . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 387-94-E
* Listings and Approvals are under NOTIFIER a Division of Pittway Corporation. Listingswith CSFM and MEA are for FCPS-24 only.
Ordering InformationShippingWeight
No. Description lb. (kg)
418563 FCPS-24F Remote Power 25 (11.3)Supply, 120 VAC, Red
418564 FCPS-24FE Remote 25 (11.3)Power Supply, 220 VAC, Red
417692 Battery Pack, 7 AH, 13 (5.9)24 VDC (two-12 volt batteries)
417699 EOL Power Supervision Relay 1 (0.45)
TERMINAL DESIGNATIONSTO TRANSFORMER #2
CUT JP1 TO USE A LISTED EXTERNAL BATTERY CHARGER.
CUT R134 AND R76 TO ENABLE TROUBLE REPORTING ONCONTROL INPUT #1.
CUT R175 TO MAKE OUTPUT #2 CONSTANT ON 24 VDC.
CUT R176 TO MAKE OUTPUT #4 CONSTANT ON 24 VDC.
TO TRANSFORMER #1
EA
RT
H
TB1
P1
P2
JP1
JP2
BATTERY FUSE 10A 3AG SLOW BLOW
R27
TB2
R175
R76
R176
TB4
2.2
K
2.2
K
1 2 3 4 5 6 7 8 9 10 11 12
R63
TB3R134
D31
1 IN +
2 IN – (Control Input #1 from FACP)
3 OUT +/TROUBLE CONTACT
4 OUT –
5 TROUBLE CONTACT
6 IN +
7 IN – (Control Input #2 from FACP)
8 AUXILIARY OUTPUT (+24 VDC, 10 mA max)
9 AUXILIARY OUTPUT RETURN
BA
TT
ER
Y(+
)
BA
TT
ER
Y(—
)
7 A
H, 2
4 V
DC
AC
ON
AC
FA
ILU
RE
/EA
RT
H F
AU
LT
BA
TT
ER
Y/C
HA
RG
ER
TR
OU
BLE
OU
TP
UT
1 T
RO
UB
LE
OU
TP
UT
2 T
RO
UB
LE
OU
TP
UT
3 T
RO
UB
LE
OU
TP
UT
4 T
RO
UB
LEO
UP
UT
1 +
(Sty
le Y
/Z)
OU
TPU
T1
-(S
tyle
Y/Z
)
OU
TPU
T1
+ (S
tyle
Z)
OU
TPU
T-
(Sty
le Z
)
OU
TPU
T2
+ (S
tyle
Y)
OU
TPU
T2
-(S
tyle
Y)
OU
TPU
T3
+ (S
tyle
Y/Z
)
OU
TPU
T3
-(S
tyle
Y/Z
)
OU
TPU
T3
+ (S
tyle
Z)
OU
TPU
T3
-(S
tyle
Z)
OU
TPU
T4
+ (S
tyle
Y)
OU
TPU
T4
-(S
tyle
Y)
AC
NE
UT
RA
L
AC
HO
T
INPUT 1
FCPS-24(E)
AUXILIARYOUTPUT
INPUT 2
OUTPUT 1
OUTPUT 2
OUTPUT 3
OUTPUT 4
SLC LOOP
FACPADDRESSABLE
CONTROL MODULE #1
CONTROL MODULE #2