FC-33/9, Institutional Area, Jasola, New Delhi-110025 ...urducouncil.nic.in/tender/pdf/Tender-Documents-for-DREAM-Project.pdf · FC-33/9, Institutional Area, Jasola, New Delhi

Tender No: 18-1 (16)/2014/DREAM/NCPUL

NCPUL 1 (Signature of Tenderer)

National Council for promotion of Urdu Language (NCPUL)

FC-33/9, Institutional Area, Jasola, New Delhi-110025

Tender Document for

Supply, Installation, Testing and Commissioning of Electronics Equipments, Hardware

Items, Home Appliances & Consumables

National Council for Promotion of Urdu Language, FC-33/9, Institutional Area, Jasola, New

Delhi-110025, invites technically sealed complete and commercially competitive tenders from

reputed bidders for supply, install, configure, testing and commissioning of Electronics

Equipments, Hardware Items, Home Appliances & Consumables for 50 NCPUL‟s centres

spread in the following states of India: Bihar, Delhi, Jammu & Kashmir, Jharkhand &Uttar

Pradesh (address of 50 Centres attached as Annexure-I). The tender document would be

available on NCPUL website (www.urducouncil.nic.in) and on Central Public Procurement

Portal (eprocure.gov.in) from 15 June, 2014.

1. INSTRUCTIONS TO BIDDERS

1.1 Scope of Work

The successful Tenderer will take total responsibility for supply, installation, testing and

commissioning of Electronics Equipments, Hardware Items, Home Appliances &

Consumables supplied by him. The Tenderer will be required to provide warranty at all locations

for allappliances (wherever applicable) which will be installed, configured and used to carry out

various functions. The Tenderer may also be required to arrange for inspection/testing of various

functions as per technical specifications to the representatives of NCPUL.

The successful bidders shall provide comprehensive maintenance support services during warranty

period for equipments supplied, commissioned and installed by him at all locations. This involves

comprehensive maintenance and repair of supplied equipments including replacement of part(s)

modules, sub-modules, assemblies, sub-assemblies, spares, etc. to make the equipment operational.

This will include all kind of breakdown maintenance and preventive maintenance. The breakdown

could be for any reason. The Electronics Equipments, Hardware Items & Home Appliances

supplied by the Tenderer shall be under on-site comprehensive warranty for one year or OEM

Standard warranty (whichever is higher). 10% of the billed amount in the form of Performance Bank

Guarantee will be retained to ensure proper maintenances to cover the warranty. NCPUL will have right

to get the repair work of defective equipment done locally within the users arrangements and reimburse

the expenditure thereof to users in case tenderer fails to provide services within 48 hours from the time

of break down reported.

1.2 Cost of Tender Document

The tenderer has to purchase tender document against payment of

Rs.1000/- either in cash or in the form of demand draft drawn on Nationalized/Scheduled Commercial

Bank favouring „Director, NCPUL-DEEEP‟ payable at New Delhi.

In case the tender document is to be sent by post, Rs100/- will be charged extra. However,

NCPUL will not be responsible for non-delivery / postal delays. In case the tender document is

downloaded from the website, the tenderer shall have to deposit cost of tender of Rs. 1000/-

separately along with Technical bid in the form of Demand Draft drawn on Nationalized/Scheduled

Commercial Bank in favour of „Director, NCPUL-DEEEP‟ payable at New Delhi which is not

refundable.



1.3 Schedule of Events

S. No. Information Details

1. Name of Purchaser National Council for Promotion of Urdu

Language (NCPUL)

2. Cost of Tender Document (non-

refundable)

Rs. 1,000/-

3 Earnest Money Deposit (EMD) Rs. 7,00,000/- (seven lacs)

4 Publishing Date 15June, 2014

5 Last date for Submission of Queries 27 June, 2014

6 Response to Queries & Pre-Bid

Conference

30 June, 2014 at 11:30am

7 Venue for Pre-Bid Conference National Council for Promotion of Urdu

Language (NCPUL), Plot No. 9, FC-33,

Institutional Area, JASOLA Vihar, New Delhi

– 110025.

8 Uploading of Responses to Queries on

website & Issue of Corrigendum, if any

01 July, 2014

9 Last Date & Time of Bid Submission 08 July, 2014 1300 Hrs

10 Tender Opening Date & Time 08 July, 2014 1430 Hrs

11 Date & Time of opening of Financial

bids

Will be intimated later to the Shortlisted

Bidders

12 Website for downloading Tender

Document, Corrigendum, Addendums

http://www.urducouncil.nic.in

13 Tender Validity 120 days from the date of bid submission

14 Contact Person for Queries Assistant Education Officer – Vocational

Education, National Council for Promotion of

Urdu Language, Plot No. 9, FC-33,


– 110025 15 Addressee and Address at which bids

in response to Tender Invitation are to

be submitted

The Director, National Council for Promotion

of Urdu Language, Plot No. 9, FC-33,


– 110025

http://www.urducouncil.nic.in/



1.4 Eligibility Criteria

The tenderer should fulfill the following criteria (by furnishing the information showing

proof for all the criteria listed below):

I. The tenderer quoting for the tender should have at least 5 years of experience in similar

business. The tenderer should have experience of executing at least one project of similar

nature covering ITI‟s / Polytechnics / Engineering Colleges, etc. in different States.

II. The minimum turnover required during each of the last three financial years for tenderer

is Rupees 5 (five) crores.

III. The tenderer should be in sound financial conditions and should be in profits. A copy of

last three financial years Profit & Loss Statement and relevant audited Balance Sheets

should be submitted with the offer.

IV. The tenderer should be ISO 9001:2008 certified.

V. Affidavit duly attested by Notary Public stating that the bidder has not been blacklisted by

any institution/organization/society/company of the Central/State Government

ministry/department, or its public sector organizations during the last three years.

VI. The tenderers should submit an undertaking that it has sufficient resources to supply

Electronic Equipments, Hardware items and Home appliances all over India. This may be

incorporated in the affidavit.

VII. The Registration Number of the firm along with the CST/VAT No. allotted by the Sales

Tax Authorities, PAN, TIN and copy of Income Tax Return for the last three financial

years should be given in the technical bid, failing which Tenderer's bid would become

invalid and same shall be rejected.

VIII. For a bidder, who has submitted the tender bids, it will be automatically assumed that he had

accepted all the terms and conditions of the tender. No request for deviation in the terms and

conditions of the tender will be entertained. If there is any deviation from the terms and

conditions of the tender or the tenderer has submitted conditional bids, the bid will be

summarily rejected.

IX. Upon verification, evaluation/assessment, if in case any information furnished by the

Tenderer is found to be false/incorrect, their total bid shall be summarily rejected and no

correspondence on the same, shall be entertained. In such cases, EMD shall be forfeited.



1.5 Mandatory List of Documents to be submitted

Sl. No.

Check list of Certificates/attachments Page No.

1. Bank Draft/proof for purchase of Tender Document

2. Bank Demand Draft for EMD

3. Documentary evidence of turnover of Tenderer (Last 3 years balance sheet)

4. Experience Certificates

5. Attested copies of VAT, Service Tax, Registration No., Income Tax Return,

PAN& TIN.

6. Any of the following (If applicable):

i. Articles of Association

ii. Bye-Laws or Certificate of Registration

iii. Partnership Deed

7. Affidavit duly attested by the Notary Public for never being blacklisted

8. An undertaking on letter head to the effect that tenderer has sufficient resources to supply all the tendered items i.e. Electronics Equipments, Hardware Items, Home Appliances & Consumables, all over India (to be attached in original)

9. Documentary evidence of ISO 9001:2008 Certification

10. Certificate of Acceptance of Terms and conditions

Note: All the documents must bear continuous page number, stamp and signature of

the tenderer



2. GENERAL TERMS AND CONDITIONS

2.1 TENDERERS MUST QUOTE RATES ONLY IN THE ENCLOSED PROFORMA.

2.2 The Tender document is not transferable and its cost is not refundable under any

circumstances.

2.3 The tenders should be valid for 120 days from the last date for submission of the tender.

2.4 In case of untoward delay, if any, tenderers may be requested by NCPUL to submit their

willingness in writing to extend the validity of the bids for the requested period.

Normally, the date of submission and opening of bids shall not be extended. However,

in exceptional circumstances or when the bidding document is required to be

substantially modified as a result of discussions in pre-bid conference and the time with

the prospective bidders for preparation of bids appears insufficient, the date may be

extended by the Director, NCPUL and due publicity to such change in date of

submission of bids shall be given. In such cases, it shall be ensured that after issue of

corrigendum, reasonable time is available to the bidders to prepare and submit their

bids. Any change in date of submission and opening of bids shall also be placed on the

respective websites immediately. However, if the modifications in the bidding

documentor in specifications of goods are substantial, fresh publication of original bid

inquiry may also be issued. The tendering authority may, at its discretion, extend the

deadline for the submission of bids by amending the bidding document, in which case

all rights and obligations of the tendering authority and bidders previously subject to the

deadline shall thereafter would be subject to the deadline as extended.

2.5 Pre-bid Meeting: NCPUL shall hold a pre-bid meeting with the prospective bidders on

30.06.2014 at 11.30 a.m. in the Conference hall, National Council for Promotion of

Urdu Language (NCPUL), Plot No. 9, FC-33, Institutional Area, JASOLA Vihar, New

Delhi – 110025. Queries received, from the bidders, upto 27th

June, 2014 shall be

addressed. The queries can be sent to NCPUL through email to [email protected].

Response to the queries will be uploaded on the website http://www.urducouncil.nic.in

by 1st July 2014 and, if required, Corrigendum will also be uploaded on the said website.

2.6 The tenderer must quote for all the items. L1 will be evaluated on the basis of overall

cost.

2.7 Tender Bid Submission: The tenderer will be required to submit sealed tender in a

large envelope superscribing “TENDER FOR THE SUPPLY OF ELECTRONICS

EQUIPMENTS, HARDWARE ITEMS, HOME APPLIANCES & CONSUMABLES

FOR NCPUL” further containing two separate envelopes.

The FIRST ENVELOPE must contain the Performa to be filled in by the Tenderer

Qualification Bid,separate draft for the Tender Cost or copy of the Payment Receipt (in

case, tender is purchased in person), Earnest Money Draft from Nationalized/Scheduled

Commercial Bank, TECHNICAL BID consists of the technical specifications of the items

offered along with the supporting literature, brochures, drawings, names of the

supplier/manufacturer, standard warranty period as offered by OEM.The envelope should

be sealed and superscribed in bold letters:

mailto:[email protected]

http://www.urducouncil.nic.in/



“TECHNICAL BID FOR SUPPLY OF ELECTRONICS EQUIPMENTS,

HARDWARE ITEMS, HOME APPLIANCES & CONSUMABLES”

The SECOND ENVELOPE MUST CONTAIN THE FINANCIAL BID showing

rates. The envelope should also be sealed and superscribed in bold letters:

"FINANCIAL BID FOR SUPPLY OF ELECTRONICS EQUIPMENTS,

HARDWARE ITEMS, HOME APPLIANCES & CONSUMABLES”

2.8 Bid Evaluation:While opening the tenders, the envelopes containing Technical Bid shall be openedfirst and acceptance of the tender according to the specified clauses will be ascertained. Financial Bid of only those tenderers will be opened who qualify the eligibility criteria on the basis of Technical Evaluation. For opening of Financial Bids, separate date will be fixed.

2.9 Earnest Money Deposit: Tenderers have to deposit interest free earnest money of

Rs.7,00,000/- (rupees seven lacs) in the form of demand draft drawn on

Nationalized/Scheduled Commercial Bank in favour of „Director, NCPUL-DEEEP’

payable at New Delhi which will be returned to successful bidder without any interest after

successful installation of the Electronics Equipments, Hardware Items, Home

Appliances & Consumables and submission of the Performance Bank Guarantee to cover

warranty period from the last date of successful installation of the Electronics

Equipments, Hardware Items, Home Appliances & Consumables at all locations.

NO TENDER WITHOUT COST OF TENDER DOCUMENT AND EARNEST MONEY DEPOSIT WILL BE ENTERTAINED.

2.9.1Forfeiture of Earnest Money Deposit (EMD)

The EMD submitted along with the bid shall be forfeited under the following

conditions:

a) If the bid is withdrawn during the validity period or any extension agreed to by

the Bidder thereof.

b) If the bid is varied or modified in a manner not acceptable to NCPUL after

opening of Bid during the validity period or any extended period.

c) If the Bidder tries to influence the evaluation process.

d) If the Bidder does not accept the correction of errors in his bid.

e) If the Bidder refuses to take up the job within the time stipulated by NCPUL.

f) If the Bidder, having been notified of his selection, fails or refuses to submit

the required Performance Bank Guarantee within the time stipulated by the

NCPUL.



2.9.2Refund of EMD

The EMD will be refunded as follows:

a) In the case of unsuccessful bidders, the EMD will be returned to them without

any interest accrued thereon within 90 days after the award of the contract to

the successful bidder.

b) In the case of selected bidder(s), the EMD shall be refunded within 30 days

without any interest after successful installation of equipments at all locations.

2.10Incase of increase in requirement of any item during next six months from the date of

Purchase order, tenderer will have to supply items of the same make and model and at

quoted prices.

2.11. Prices quoted should be Free of Delivery (F.O.D.) at destination sites of NCPUL all over India

(quantity may vary at the time of placing the supply order) inclusive of all charges

like sales tax/VAT, excise duty, insurance, technical service/installation charges and

octroi etc. No other charges/taxes/levies shall be payable. No form „C‟/ „D‟/undertaking

will be provided by NCPUL.

2.12Tenderers qualified in the Technical Bid may be required to demonstrate their equipments

at National Council for Promotion of Urdu Language, New Delhi for bench marking the

products.

2.13Delivery Schedule: Purchase Order shall be raised to the successful bidder. Electronics

Equipments, Hardware Items, Home Appliances & Consumables must be delivered

and installed within 4 (four) weeks from the date of issue of the purchase order. Penalty

for late delivery would be liable at the rate of 0.5% per day subject to a maximum of 10

percent of the value of such portion of material as has not been supplied within the

stipulated period. In case delivery is not completed within 20 days after the specified

delivery period, NCPUL may cancel the order and arrange to procure the said items from

any other source at the risk and cost of the tenderer(s) and EMD/PBG will be forfeited.

2.14PAYMENT TERMS

The terms of payment will be as follows:

(i) Bill will be raised in the name of the Director, National Council for Promotion of Urdu

Language, FC-33/9, Institutional Area, Jasola New Delhi-110025 alongwith installation

reports and other relevant documents.

(ii) No advance payment against purchase order will be made.

(iii) 80% of the billed amount will be paid within 30 days of submission

of the bill along with; (a) Original Ink signed with office stamp, copy of delivery and

successful installation report from Centre-In-charge of NCPUL centre where the complete

lot of equipments is delivered (b) Consolidated summary report of items delivered at each

centre on the prescribed format (to be provided with supply order to the successful bidder)

showing successful delivery, Installation and satisfactory functioning of Electronics

Equipments, Hardware Items, Home Appliances & Consumables.



(iv) 20% of the billed amount will be paid by NCPUL on completion of installation of all the

items at all the NCPUL Centres and upon receipt of 10% Performance Bank Guarantee

(PBG) to cover the warranty.

2.15 NCPUL reserves the right to reject any or all tender(s) without assigning any reason.

2.16 Sealed tenders, complete in all respects, should reach National Council for Promotion of

Urdu Language, FC-33/9, Institutional Area, Jasola New Delhi-110025 latest

by01:00pmon 08.07.2014. Technical bids will be opened on the same date at

02.30p.m. in the presence of the representatives of the tenderers, who wish to attend the

Technical Bid opening. Incomplete tenders or those without earnest money and

requisite tender fee would be outrightly rejected. The Financial Bids of bidders

qualifying the technical evaluation will be opened at a date that would be fixed

separately.

2.17 NCPUL reserves the right to revise or alter the requirements and/or specifications of the

material before acceptance of any tender and call for revised tenders.

2.18 Supply, complete in all respects, will be accepted in one lot at each location.

2.19 All the pages forwarded with the quotation should be sequentially numbered and shall

be signed by authorized signatory with organization‟s rubber stamp.

2.20 Users at site will conduct the acceptance test(s) on the Equipments& Appliances

ordered. If the Equipments& Appliances supplied fail in the test(s), the same may be

rejected. Replacement of cards or defective part will not be allowed.

2.21 The acceptance test will be done as per the specifications of the equipments&

components.

2.22 NCPUL reserves the right to reject all or any item, if supplied material is found

defective within 30 days after successful installation.

2.23 Tenderer(s) must specify the make and model of items quoted along with printed

brochure of the products quoted in the Technical bid.



2.24 Tenderer(s) will be responsible for comprehensive maintenance of Electronics

Equipments, Hardware Items, Home Appliances & Consumables, free of charge,

during warranty period of Electronics Equipments, Hardware Items & Home

Appliances after the acceptance of supplied material at all locations. In case of

default, NCPUL will have the right to arrange maintenance at tenderer‟s risk against

the Performance Bank Guarantee.

2.25 Comprehensive maintenance will cover replacement of all defective parts/equipments.

2.26 Tenderer(s) should have satisfactory arrangement to receive complaints at all

locations at which material will be supplied and provide maintenance at these places.

The contact details of service centre will be provided to each NCPUL centre with a

copy to NCPUL, New Delhi. The response time for attending faults will be four hours

after these are reported to the tenderer. The tenderer will rectify the faults within 24

hours failing which tenderer will arrange temporary replacement of the equipment. In

case, the tenderer fails this requirement within 48 hours, NCPUL will have the right to

arrange repairs/replacements at the costs and risk of the tenderer.

2.27 The Tenderer, shall at all times, indemnify NCPUL against all claims, damages or

compensation under the provisions of Payment of Wages Act, 1936, Minimum Wages

Act, 1984, Employer Liability act, 1938, Workmen‟s compensation Act, 1923,

Industrial Disputes Act, 1947 and the Maternity Benefit Act, 1961, or any

modifications thereof or as a consequence or any accident or injury to any workman

or other persons in or about the Works, whether in the employment of Tenderer or

not.

2.28 Tenderer will be responsible to provide insurance cover to man, machines materials

involved till successful installation.

2.29 Tenderer will not sublet/transfer whole or any part of the assigned work to other(s).

2.30 Tenderer(s) should also give preventive maintenance schedule for the equipments

along with their offer. This schedule will have to be adhered to by the tenderer

strictly.

2.31 The Tenderer(s) must specifically mention the place, from where support for

maintenance would be offered.

2.32 All dispute and differences and questions arising out of, in any way touching or

concerning NCPUL and Tenderers, will be referred to the sole arbitration of the



Director, NCPUL or any person appointed by him. Arbitration shall be in accordance

with the Conciliation Act 1996. The arbitrator shall be entitled to extend the time of

arbitration proceeding with the consent of the party. In case of failure of arbitration

proceedings, the appropriate Courts at Delhi alone shall have jurisdiction to entertain

and try them.

2.33 Non-compliance of the above terms and conditions will be treated as non-responsive

and such bids are liable to be rejected.

2.34 Copy of these terms and conditions duly signed and stamped on each page must be

attached with the technical bid for acceptance of the above terms and conditions.

DECLARATION

I/We ……………………………. have read all the terms & conditions as laid down in NIT and

Tender document and agree to abide by them.

(Signature)

Seal



National Council for promotion of Urdu Language (NCPUL)

QUALIFICATION BID

PLEASE COMPLETE THE FORM AND ENCLOSE NECESSARY DODUMENTS WHERE REQUIRED OTHERWISE THE TENDER WILL BE REJECTED

BID PARTICULARS FOR TENDER NO. : _________________________________ 1) Name of the Bidder : _________________________________ 2) Address of the Bidder : _________________________________

_________________________________

_________________________________

Telephone :

Fax :

E-mail :

3) Bidder’s proposal number and date : 4) Name & Address of the officer :

To whom all references shall be

made regarding this tender

Telephone :

Fax :

E-mail :

5) Earnest Money : Bank/Demand Draft

Date

Bank/Demand

Draft No.

Drawn on Nationalized/Scheduled

Commercial Bank

Amount

6) No. of years of experience :

(Attach certificates from Client - for successful running) 7) Turnover of Tenderer (for last 3 years) : 2011-12 2012-13 2013-14 8) Similar Supplies in Educational Institutions: (Reference of Organization with Purchase Order)



9) Service Station/Maintenance Facility : 10)Copy of Income Tax returns : Yes/No (Attach attested copies) 11) CST/VAT Registration Certificate : Yes/No

(Attach attested copies) 12) An affidavit duly attested by the Notary : Yes/No

Public that the firm has never been Black Listed

(Attach original affidavit on Rs.10/- Stamp paper) 13) PAN : 14) TIN : 15) Documentary evidence of ISO Certification

(Attach attested copy) : Yes/No I/We have read all the terms and conditions of tender and accept them in full (Enclose a certificate of

acceptance)

(Signature) Seal

DECLARATION

I/WE DECLARE THAT THE INFORMATION SUPPLIED ABOVE IS CORRECT TO THE BEST OF MY/OUR KNOWLEDGE.

(Signature) Seal



TECHNICAL BID

A. List of Electronics Equipment, Hardware Items & Home Appliances

Sr. No.

Name of The Item Specification Qty Required at each Centre

Total Qty. for 50 centres

Make or Model Offered

Certified product Y/N

Deviation if any

1 Screw Driver Kit Single Handle, Multiple Size Bits including flat, star & cross head type

10 500

2 D Spanner set open end (8 pieces)

6 x 7, 8 x 9, 10 x 11, 12 x 13, 14 x 15, 16 x 17, 18 x 19, 20 x 22 (mm)

10 500

3 Ring Spanner Sets (8 pieces)

6 x 7, 8 x 9, 10 x 11, 12 x 13, 14 x 15, 16 x 17, 18 x 19, 20 x 22 (mm)

10 500

4 Allen Key Set (9 pieces) 1.5mm, 2mm, 2.5mm, 3mm,

4mm, 5mm, 6mm,

8mm,10mm

10 500

5 Plier (Insulated) Long Nose 6 Inches 10 500

6 Combinational Plier (insulated)

Insulated grip 10 500

7 Screw Driver cum Mains Tester

125 mm 10 500

8 Wire Stripper (insulated) Adjustable wire size Insulated vinyl grip

10 500

9 Wire Cutters(insulated) 0.18-1.2 mm copper 10 500

10 Cross Pein Hammer with handle

500 grams minimum 10 500

11 Tweezers 6" 10 500

12 Small Hacksaw with Blade

8” Size 10 500

13 Soldering Iron With Stand 25 Watts 10 500

14 Soldering Iron With Stand 10 Watts 10 500

15 De-Soldering Pumps · metal housing 10 500

· Strong vacuum

· antistatic

· length 200 mm

16 De-Soldering Wick Minimum 2.5 mm wide, 25 Feet long with Superior wetting properties

10 500

17 Multimeter (Low End) · Display: 22mm data height LCD Display

10 500

· Max. Indication : 1999 ( 3 ½ ), auto polarity indication

· Sampling Rate :approx . 3times/sec

· Low Battery Indication

· Operation (0~40)0 C, relative humidity < 80%



· Accessories : Manual, test lead and battery.

· DCV : 200mV/ 2V/20V/20V/200V:+ (0.5% + 4), 600V : + (1.0% +5)

· ACV : 200V/600V : + (1.2% +10)

· DCA : 200uA/2mA/20mA/ 200mA: + (1.5% +3), 10A : + (2.0 %+5)

· Resistance : 200Ω: + (0.8% +5), 2kΩ/20k Ω/200k Ω : + (0.8% +3), 20 Ω : + (1.0% +5)

18 Multimeter Digital Clamp meter

· Display : 6000 counts 1 50

· RMS Method : Average Responding

· DC V : 600V

· AC V : 600V

· AC Current : 400A

· Resistance : 600 ohm to 6k ohm

· Diode : 1.5V

· Continuity : 600ohm

· Auto Power Off: Yes

· Clamp opening : 31mm Minimum

· Clamp diameter : 27mm Minimum

Over – Voltage safety protection : CAT III 600V/ CAT IV 300V

19 Glue Gun 60 Watts, 110-230 V AC 2 100

20 Silicon Glue Stick Suitable for Glue Gun 10 500

21 Files(Iron) Fine (Flat), Minimum 10” Suitable for grounding solder iron tip

10 500

22 Power Supply Unit · 0-30V DC/5A 5 250

· Constant Current and Constant Voltage

· 2 Digital Panel Meters (DPMs) - One DPM for Voltage and other DPM for Current

· High Efficiency , Light and Compact Design

· High Power Density

· Overload and Reverse Polarity Protection

· 3 digits LED Display

· Cooling fan located internally.

23 Hot air soldering Gun for SMD soldering

· Power supply : 230V AC +- 10%, 50 Hz

2 100

· Power Consumption: 300 Watt Max.

· Hot Air Iron : 100Watt

· Channel : 2



· Temperature Range : 500 C to 5500 C

· Temperature Accuracy : + 2%

· ESD safe

· Display : LCD

· Hot Air Flow : 10l/min

· Nozzle : 3mm dia& 1.2 mm dia

· Stand with sponge

· Flux pen

24 Table Vice Jaw Width: 4”, Jaw Opening: 4.5”

1 50

25 Portable Electric Drill Machine

Rated Voltage = 230V, 50Hz Rated Input Power = 500 W Chuck Diameter =10mm Drill Type = Hammer Drill

2 100

26 ESD safe Electronic Work Bench with Multimeter, Digital Storage Oscilloscope and Power Supply

Assembly :Table should have 3 sub assemblies

1 50

Bottom stand Pi type structure with table top, drawers etc.

Hind Switch box, to hold 1ph.& 3ph. power source

Top side rectangular box mounted on top of hind switch box to house various instruments like CRO, Multimeter& power supply etc

Frame : 16 gauge, MS square tube (Heavy duty) Colour : Brown / Off white powder coated, optionally with sturdy aluminium profile frame

Table Top Material/Colour : The nova pan or Rubber wood with white / silver gray colour & smooth finish, Veneer finish table top (min. 18 mm thick)

Drawer : Drawers to have vertical position

• Out of 3 drawers, one should be of open type & would double up as PC keyboard drawer with mouse pad on its side. Other two drawers should be of closed type, lockable.



• Pull Output Writing pad provided above upper drawer on right side of table

• Dimensions of drawer :

Upper Drawer: Min. 600 mm (L) x 400 mm (W) x 200 mm (H)

Tall Drawer : Min. 600 mm (L) x 400 mm (W) x 200 mm (H)

Open Drawer : Min. 700 mm (L) x 400 mm (W) x 045 mm (H)

Writing Pad: Min. 335 mm (L) x 300 mm (W) x 010 mm (H)

Bottom Legs having Castor Wheel with locking mechanism to be provided so that table can be easily moved

Overall Dimensions: Min. 1200mm(L) x 750mm(W) x 1325mm(H)

Electrical Fitting: Hind (Switch) box with screwable hind side panel to facilitate wiring & controlling 6 separate sets of 5 Amp switch & 5 pin 3 phase proof protective Socket with 4 Pole MCB Neon indicators provided on the facing panel of switch box.

(A)DC REGULATED POWER SUPPLY

• 0-64 VDC/ 5 A, Line Regulation : 0.1%, Load Regulation: 0.1%, Maximum Ripple: <5 mV, Operating Temperature : 0 to 50 C, Display : 2 sets of 3 digits LED

• Line Power Supply : 220V +/- 10%, 50Hz, Constant Current and Constant Voltage, 2 DPMs, 1 for Voltage and One for Current, 3 Digit LED Display, CV and CC Indicators, Overload Protection, Low temperature drift, Multiturn potentiometers, easy to set up voltage and current



(B) 3 ¾ DIGITAL MULTIMETER with LCD display

Max Display : 4000 ( 3 ¾ ) digits automatic polarity

Sampling rate : approx. 3 times/sec

Over-range display : "OL" displayed in the highest digit.

Working environment: (0-~40)0C, relative humidity: <80%

Store environment : (-10~40) 0C, relative humidity: <80%

Accessories : test leads, user manual, temperature probe, holster, and battery.

Accuracy: + (% reading + digits), environment temperature at (23+5) 0C, relative humidity<75%

DC Voltage (DCV)

Range Max. Resolution Accuracy

400.0mV 0.1mV + (0.5% + 5)

Overload protection: 1000V DC or 750V AC.

AC Voltage (ACV)


4.000V 1mV + (1.0% + 5)

Overload protection: 1000V DC or 750V AC.

Frequency response: (40~200)Hz under 750V

Sine wave RMS (Average value response.)

DC Current (DCA)


400.0µA 0.1µA + (1.5% + 2)

MAX input current: 10A (within 15 seconds)

Over load protection: 400mA/250V and 10A/250V



AC Current (ACA)


400.0µA 0.1µA + (1.5% + 2)

MAX measurement voltage drop: full range mA: 400mV, A:200mV0

Max input current: 10A (within 15 seconds)


RESISTANCE (Ω)


400.0Ω 0.1Ω + (1.2% + 2)

(C) 50 MHZ DIGITAL STORAGE OSCILLOSCOPE

·Bandwidth : DC to 50 MHz

·Memory Depth/ Record Length: 8kpts all channels or better

·Sampling Rate: 1 GSa/Sec

· Vertical Input Sensitivity : 2 mV/div to 10V/div or Better

·Time base Range: 5 ns/div to 50 s/div or Better

· Automatic Measurement : 20+ including like as voltage, time, and frequency as Well as four waveform math functions including FFT

·Waveform Update Rate: 200 waveform update rate per second

· Vertical Resolution : 8 bit

· Large 5.7 inch diagonal colour TFT LCD display

The Manufacturer should have National Accreditation

Board for Testing and Calibration Laboratories

(NABL) accredited calibration facility in India.

27 Soldering/ De-soldering Station (ESD safe) with multiple tips

25 watts 2 100

28 SMPS Adapter Output :12V DC-1Amp, Input 100V-270V AC

5 250

29 Bit Set for Drill Machine 2 mm, 2.4 mm, 3 mm, 3.2 mm, 4 mm, 6 mm, 8 mm, 10 mm

2 100

30 Steel Almirah with Lock and Key

Minimum 72”(H)X 36”(W)X 20”(D), Minimum 20 Gauge steel sheet

2 100



31 Electricity Extension Board

230 V Screw fitted with Indicator, 4 nos. 5Amp 5 pin Socket, 5Amp Switch with Fuse Protection

5 250

32 Insulation tester/Meggar 0 to 200 M ohm, testing voltage 1000 volt, resolution 0.1 M ohms

1 50

33 Measuring Tape Steel- minimum 10 Feet long

2 100

34 First Aid kit with box Standard Kit 1 50

35 Colour Television LCD Display Size : Minimum 21” Diagonal

1 50

36 Colour TV with CRT CRT Picture Tube Display Size : Minimum 21” Diagonal

1 50

37 Cable Preparation Tool Suitable for stripping Coaxial cablesRG6, RG59

2 100

38 Compression Tool for F connector

For use on RG6 and RG59 cable F- Connector

2 100

39 Satellite Meter For DTH installation 2 100

40 Angle finder For DTH installation 2 100

41 Set Top boxes with Dish Free DTH with all fixtures and 20 meter cable

1 50

42 Set Top boxes with Dish Paid DTH – 1 nos of a Service provider with all fixtures, 20 meter cable and 3 years basic pack’s subscription

1 50

43 Spirit Level Rectangular, unbreakable, length 100mm minimum

5 250

44 Washing Machine Semi Automatic twin tub - minimum 6 KG ISI mark

1 50

45 Microwave Oven 20 Ltr with Convection - Mechanical Timer for training purpose

1 50

46 High Voltage Tester for MWO

10 KV, Display : Digital 1 50

47 Box panel Hose Clip for water purifier

Suitable for pipes used in water purifiers

10 500

48 RO Spanner 8 - 9 2 100

49 RO membrane Spanner standard 2 100

50 RO pipe Cutter Plastic pipe cutter, 5mm to 16 mm

2 100

51 Monkey Plier Insulated grip, length 200 mm minimum

10 500

52 Screw Driver Big Tip size 5.5mmx0.6mm, 200 mm length

10 500

53 TDS Meter Measurement Range : 0999ppm Resolution : 1ppm for 0-999ppm and 10ppm for 1000-9990ppm Display -LCD Suitable for water quality measurement

2 100

54 Water Purifier minimum 8 litre storage with RO & UV

1 50

55 Pipe Wrench Stillson Type

10" 2 100



56 Juicer/Mixer/Grinder minimum 450 watt motor 1 50

57 UPS Trainer Input range: 170-270V A.C./50Hz.

1 50

• Output (Input present) 195-250V sine.

• 230 V + 5% Quasi-sine.

• Capacity 200W lamp load on AVR.

• 12V / 7Ah Maintenance free lead acid Battery

• Backup of 5 minutes on 200W lamp load or 20 minutes on one PC with 14” colour monitor.

• Minimum 17 test points

Panels :

• Input / Output Module

• Battery / Transformer Module

• AVR / Charger Module

• Inverter Module

58 Tubular Battery 12V-80AH (Lead Acid) 2 100

59 Solar Inverter 600 VA with variable input voltage 11 V – 18 V

1 50

60 Charge Controller 12V– 5A 4 200

61 Charge Controller 24V – 5A 4 200

62 Solar Panel 12V - 36 Wp Rating, Aluminium Framing with Glass protection

3 150

63 Solar Panel 12V - 100 Wp Rating, Aluminium Framing with Glass protection

3 150

64 Lux meter Display : LCD, Range : 0-50000 Lux in3 Ranges

1 50

65 Mobile Charger with Multi Pin connector

Input Voltage - 110-240V AC Output Voltage : 5.5 VDC

10 500

66 Screw Driver Adjustable Torque : 1-5kgf.cm Torque Indication

1 50

67 Rheostat 10 ohm, 5 A 2 100

68 Magnifier with illumination lamp

Glass Lens ( Magnifier ) 3.5 Inch with fluorescent illumination

5 250

69 Wrist Band ESD Safe 10 500

Note: All the items mentioned above should be of good quality, standard brand and certified by

BIS/IECEE acceptance or equivalent, wherever applicable.



B. List of Consumables

Sr. No.

Name Of The Item Specification Qty Required per Centre

Total Qty. for 50 Centres

Make or Model Offered

Certified product Y/N

Deviation if any

1 Hookup Wire – 90 Meter Length Bundle

24 SWG 2 100

2 Insulated Connecting Wire (Red, Yellow, Blue, White, Grey, Brown, Black, Green, Orange)

14/36 (90 Meter Length Bundle)

9 450 (1 Each) (50

each)

3 Phenolic General Purpose PCB

6”x 4” size 40 2000

4 Multimeter Battery 9 V, Type 6F22 with connector

20 1000

5 Main Lead 3 Core 2 Amp Rating 10 500

6 Fuse Holder

suitable for 5 X 20 mmfuses upto 5 Amp

20 1000

7 Glass Fuse 20mm 100 m Amp 10 500

8 Glass Fuse 20mm 1 Amp 11 550



11 Hexa Blade 8” Size 40 2000

12 Machine Screw 1/8 " 100 5000

13 Machine Screw 1/4 " 100 5000

14 Soldering Flux Small Box 40 2000

15 Sand Paper Wood Type 40 2000

16 Safety Glove – pairs Latex rubber with good insulation, Medium Size

5 250

17 Isopropyl Alcohol for PCB Cleaning

1 litre packing 2 100


19 Regulator LM 7805 TO-220 Package 80 4000

20 Solder Wire Roll Lead Free, 50 gram Packing

40 2000

21 Capacitor 100uf/16V, 1000uf/16V, 470uf/16V,

Electrolytic 150 7500 (50 each) (2500

each)

22 Diode IN 4007 400 20000

23 LED 5mm (RED) 40 2000

24 LED 5mm (GREEN) 40 2000

25 White LEDs 5 mm 200 10000

26 White LEDs 1W(matka type) 200 10000

27 SPST Switch (Toggle SW) 5 AMP 40 2000

28 DPST Switch 5 Amp 10 500

29 TACT Switches 4 pin, 6mmX6mm 100 5000

30 Slide Switch – SPDT 3 position 40 2000

31 Male Berg Strip 40 pin, Pitch 100 mils 40 2000

32 Female Berg Strip 40 pin, Pitch 100 mils 40 2000

https://www.google.co.in/search?biw=1366&bih=667&q=Mechanic+Screw&spell=1&sa=X&ei=HSr_UYbpM4iGrAfvmYCIBQ&ved=0CCkQBSgA




33 Resistances (10 Ohm, 22 Ohm, 33 Ohm, 47 Ohm, 100 Ohm, 220 Ohm,270 Ohm,330 Ohm, 470 Ohm, 560 Ohm, 620 Ohm, 1 K Ohm, 1.5k Ohm, 2.2 K Ohm, 3.3 K Ohm, 4.7 K Ohm, 5.1 K Ohm, 6.8 K Ohm, 10 K Ohm, 22 K Ohm, 33 K Ohm, 47 K Ohm, 68 K Ohm, 100 K Ohm, 220 K Ohm, 330 K Ohm, 470 K Ohm)

¼ W, 5% 2700 135000 (100 each) (5000

each)

34 Variable Resistance - (1k,2k,5k,10k,100k)

Preset ( Screw type) 100 5000 (20 Each) (1000

each)

35 Relays (Sugar Cube) 6V, SPDT (Contact Rating 7A/240 V AC)

40 2000

36 Transistor BC 547 100 5000

37 MOSFET IRF Z44 40 2000

38 Transformer 6-0-6V, 1 Amp 10 500

39 Heat Sink For T0220 Package 40 2000

40 Heat Sink Compound Small Box 1 50

41 Sealed Lead Acid Battery 4 V- 1 AH 20 1000

42 Reference Voltage Source TL431

TO-92 Package 40 2000

43 LDR Minimum 5mm diameter 100 5000

44 Mobile Pin Socket Female (Round Small Pin – like Nokia mobile)

40 2000

45 Nut Bolt For Dish fixing 20 1000

Note: All the items mentioned above should be of good quality and of standard brand.

I/we hereby undertake that all the terms and conditions/specifications/requirements have been

carefully read, understood and nothing has been concealed.

(Signature)

Seal



Financial Bid

(The bidders need to sign each and every page of the financial bid) Reference to Notice Inviting Tender(NIT), Terms & Conditions, Specifications given in the Tenderand

locations of NCPUL centres, the rate including all charges/ taxes etc. involving upto at delivery, installation and operational stage of users and comprehensive onsite warranty at all locations along with Make and Model, are quoted, as under:-

A. Electronics Equipments, Hardware Items & Home Appliances Sr. No.

Name of The Item Specification Qty Required at each Centre

Total Qty. for 50 centres (A)

Unit Rate inclusive of all taxes with warranty (B)

Total Amount including all taxes A X B

1 Screw Driver Kit Single Handle, Multiple Size Bits including flat, star & cross head type

10 500

2 D Spanner set open end (8 pieces)

6 x 7, 8 x 9, 10 x 11, 12 x 13, 14 x 15, 16 x 17, 18 x 19, 20 x 22 (mm)

10 500

3 Ring Spanner Sets (8 pieces)

6 x 7, 8 x 9, 10 x 11, 12 x 13, 14 x 15, 16 x 17, 18 x 19, 20 x 22 (mm)

10 500

4 Allen Key Set (9 pieces)

1.5mm, 2mm, 2.5mm,

3mm, 4mm, 5mm,

6mm, 8mm,10mm

10 500

5 Plier (Insulated) Long Nose 6 Inches 10 500

6 Combinational Plier (insulated)

Insulated grip 10 500

7 Screw Driver cum Mains Tester

125 mm 10 500

8 Wire Stripper (insulated)

Adjustable wire size Insulated vinyl grip

10 500

9 Wire Cutters(insulated)

0.18-1.2 mm copper 10 500

10 Cross Pein Hammer with handle

500 grams minimum 10 500

11 Tweezers 6" 10 500

12 Small Hacksaw with Blade

8” Size 10 500

13 Soldering Iron With Stand

25 Watts 10 500

14 Soldering Iron With Stand

10 Watts 10 500



15 De-Soldering Pumps · metal housing 10 500

· Strong vacuum

· antistatic

· length 200 mm

16 De-Soldering Wick Minimum 2.5 mm wide, 25 Feet long with Superior wetting properties

10 500

17 Multimeter (Low End)

· Display: 22mm data height LCD Display

10 500

· Max. Indication : 1999 ( 3 ½ ), auto polarity indication · Sampling Rate :approx . 3times/sec · Low Battery Indication · Operation (0~40)0 C, relative humidity < 80% · Accessories : Manual, test lead and battery. · DCV : 200mV/ 2V/20V/20V/200V: + (0.5% + 4), 600V : + (1.0% +5) · ACV : 200V/600V : + (1.2% +10) · DCA : 200uA/2mA/20mA/ 200mA: + (1.5% +3), 10A : + (2.0 %+5) · Resistance : 200Ω: + (0.8% +5), 2kΩ/20k Ω/200k Ω : + (0.8% +3), 20 Ω : + (1.0% +5)

18 Multimeter Digital Clamp meter

· Display : 6000 counts

1 50

· RMS Method : Average Responding · DC V : 600V

· AC V : 600V

· AC Current : 400A · Resistance : 600 ohm to 6k ohm · Diode : 1.5V

· Continuity : 600ohm · Auto Power Off: Yes · Clamp opening : 31mm · Clamp diameter : 27mm



Over – Voltage safety protection : CAT III 600V/ CAT IV 300V

19 Glue Gun 60 Watts, 110-230 V AC

2 100


21 Files(Iron) Fine (Flat), Minimum 10” Suitable for grounding solder iron tip

10 500

22 Power Supply Unit · 0-30V/5A 5 250

· Constant Current and Constant Voltage · Digital Panel Meters (DPMs) · One DPM for Voltage and other DPM for Current · High Efficiency , Light and Compact Design · High Power Density · Overload and Reverse Polarity Protection · 3 digits LED Display · Cooling fan inner located.

23 Hot air soldering Gun for SMD soldering

· Power supply : 230V AC +- 10%, 50 Hz

2 100

· Power Consumption: 300 Watt Max. · Hot Air Iron : 100Watt · Channel : 2

· Temperature Range : 500 C to 5500 C · Temperature Accuracy : + 2% · ESD safe : Yes

· Display : LCD

· Hot Air Flow : 10l/min · Nozzle : 3mm dia& 1.2 mm dia · Stand with sponge · Flux pen

24 Table Vice 1 50



25 Portable Electric Drill Machine

Rated Voltage = 230V, 50Hz Rated Input Power = 500 W Chuck Diameter =10mm Drill Type = Hammer Drill

2 100

26 ESD safe Electronic Work Bench with Multimeter, Digital Storage Oscilloscope and Power Supply

Assembly :Table should have 3 sub assemblies

1 50

a) Bottom stand Pi type structure with table top, drawers etc. b) Switch box, to hold 1ph. & 3ph. power sources etc. c) Top side rectangular box mounted on top of switch box to house various instruments like CRO, Multimeter& power supply etc Frame : 16 guage MS square tube (Heavy duty) Colour : Brown /Off white powder coating, optionally with sturdy aluminum profile frame Table Top Material/Colour : The nova pan or Rubber wood with white / silver gray colour & smooth finish, Veneer finish table top (18 mm thick) Drawer : Drawers to have vertical position • Out of 3 drawers, one should be of open type & would double up as PC keyboard drawer with mouse pad on its side. Other two drawers should be of closed type, lockable. • Pull Out Put Writing pad provided above upper drawer on right side of table • Dimensions of drawer : Upper Drawer : 600 mm (L) x 400 mm (W) x 200 mm (H)



Tall Drawer : 600 mm (L) x 400 mm (W) x 200 mm (H)

Open Drawer : 700 mm (L) x 400 mm (W) x 045 mm (H) Writing Pad: 335 mm (L) x 300 mm (W) x 010 mm (H) Bottom Legs : Four rubber bottom legs are to be provided to support the table. optionally Castor Wheel with locking mechanism to be provided so that table can be easily moved Overall Dimensions: 1200mm(L) x 750mm(W) x 1325mm(H) Electrical Fitting : Hind (Switch) box with screwable hind side panel to facilitate wiring & controlling 6 separate sets of 5 Amp switch & 5 pin 3 phase proof protective Socket with 4 Pole MCB Neon indicator provided on the facing panel of switch box. (A)DC REGULATED POWER SUPPLY • 0-64 VDC/ 5 A, Line Regulation : 0.1%, Load Regulation: 0.1%, Maximum Ripple: <5 mV, Operating Temperature : 0 to 50 C, Display : 2 sets of 3 digits LED • Line Power Supply : 220V +/- 10%, 50Hz, Constant Current and Constant Voltage, 2 DPMs, 1 for Voltage and One for Current, 3 Digit LED Display, CV and CC Indicators, Overload Protection, Low temperature drift, Multiturn potentiometers, easy to set up voltage and current



(B) 3 3/4 DIGITAL MULTIMETER with LCD display

Max Display : 4000 ( 3 3/4 ) digits automatic polarity Sampling rate : approx. 3 times/sec Over-range display : "OL" displayed in the highest digit. Working environment: (0-~40)0C, relative humidity: <80% Store environment : (-10~40) 0C, relative humidity: <80% Accessories : test leads, user manual, temperature probe, holster, and battery. Accuracy: + (% reading + digits), environment temperature at (23+5) 0C, relative humidity<75% DC Voltage (DCV)

Range Max. Resolution Accuracy 400.0mV 0.1mV + (0.5% + 5) Overload protection: 1000V DC or 750V AC. AC Voltage (ACV)

Range Max. Resolution Accuracy 4.000V 1mV + (1.0% + 5) Overload protection: 1000V DC or 750V AC. Frequency response: (40~200)Hz under 750V Sine wave RMS (Average value response.) DC Current (DCA)

Range Max. Resolution Accuracy 400.0µA 0.1µA + (1.5% + 2)

MAX input current: 10A (within 15 seconds)




AC Current (ACA)

Range Max. Resolution Accuracy 400.0µA 0.1µA + (1.5% + 2) MAX measurement voltage drop: full range mA: 400mV, A:200mV0 Max input current: 10A (within 15 seconds) Over load protection: 400mA/250V and 10A/250V RESISTANCE (Ω)

Range Max. Resolution Accuracy 400.0Ω 0.1Ω + (1.2% + 2) (C) 50 MHZ DIGITAL STORAGE OSCILLOSCOPE ·Bandwidth : DC to 50 MHz ·Memory Depth/ Record Length: 8kpts all channels or better ·Sampling Rate: 1 GSa/Sec · Vertical Input Sensitivity : 2 mV/div to 10V/div or Better ·Time base Range: 5 ns/div to 50 s/div or Better · Automatic Measurement : 20+ including like as voltage, time, and frequency as Well as four waveform math functions including FFT ·Waveform Update Rate: 200 waveform update rate per second · Vertical Resolution : 8 bit Oscilloscope should have inbuilt 20 MHz function Generator,



· Large 5.7 inch digonalcolor TFT LCD display

The Manufacturer should have National

Accreditation Board for Testing and Calibration

Laboratories (NABL) accredited calibration

facility in India. 27 Soldering/ De-

soldering Station (ESD safe) with multiple tips

25 watts 2 100

28 SMPS Adopter Output :12V DC-1Amp, Input 100V-270V AC

5 250

29 Bit Set for Drill Machine

2 mm, 2.4 mm, 3 mm, 3.2 mm, 4 mm, 6 mm, 8 mm, 10 mm

2 100

30 Steel Almirah with Lock and Key

Minimum 72”(H)X 36”(W)X 20”(D), Minimum 20 Gauge steel sheet

2 100

31 Electricity Extension Board

230 V Screw fitted with Indicator, 4 nos. 5Amp 5 pin Socket, 5Amp Switch

5 250

32 Insulation tester/Meggar

0 to 200 M ohm, testing voltage 1000 volt, resolution 0.1 M ohms

1 50

33 Measuring Tape Steel- minimum 10 Feet long

34 First Aid kit with box

1 50

35 Colour Television LCD Display Size : Minimum 21” Diagonal

1 50

36 Colour TV with CRT CRT Picture Tube Display Size : Minimum 21” Diagonal

1 50

37 Cable Prepration Tool

Suitable for stripping Coaxial cables RG6, RG59

2 100

38 Compression Tool for F connctor

For use on RG6 and RG59 cable F- Connector

2 100

39 Satellite Meter For DTH installation 2 100

40 Angle finder For DTH installation 2 100

41 Set Top boxes with Dish

Free DTH with all fixtures and 20 meter cable

1 50

42 Set Top boxes with Dish

Paid DTH – 1 nos of a Service provider with all fixtures, 20 meter cable and 3 years basic pack’subscription

1 50

43 Spirit Level 5 250

44 Washing Machine Semi Automatic twin tub - minimum 6 KG ISI mark

1 50

45 Microwave Oven 20 Ltr with Convection - Mechanical Timer for training purpose

1 50



46 High Voltage Tester for MWO

10 KV Display : Digital

1 50

47 Box panel Hose Clip for water purifier

Suitable for pipes used in water purifiers

10 500

48 RO Spanner 8 - 9 2 100

49 RO membrane Spanner

2 100

50 Ro pipe Cutter 2 100

51 Monkey Plier 10 500

52 Screw Driver Big Tip size 5.5mmx0.6mm, 200 mm lenght

10 500

53 TDS Meter Measurement Range : 0999ppm Resolution : 1ppm for 0-999ppm and 10ppm for 1000-9990ppm Display -LCD Suitable for water quality measurement

2 100

54 Water Purifier minimum 8 litre storage with RO & UV

1 50

55 Pipe Wrench Stillson Type

10" 2 100

56 Juicer/Mixer/Grinder

minimum 450 watt motor

1 50

57 UPS Trainer Input range: 170-270V A.C./50Hz.

1 50

• Output (Input present) 195-250V sine.

• 230 V + 5% Quasi-sine. • Capacity 200W lamp load on AVR. • 12V / 7Ah Maintenance free lead acid Battery • Backup of 5 minutes on 200W lamp load or 20 minutes on one PC with 14” colour monitor. •Minimum 17 test points Panels :

•Input / Output Module

•Battery / Transformer Module • AVR / Charger Module

• Inverter Module

58 Tubular Battery 12V-80AH (Lead Acid) 2 100

59 Solar Inverter 600 VA with variable input voltage 11V – 18 V

1 50

60 Charge Controller 12V– 5A 4 200

61 Charge Controller 24V – 5A 4 200

62 Solar Panel 12V - 36 Wp Rating 3 150



63 Solar Panel 12V - 100 Wp Rating 3 150

64 Lux meter Display : LCD Range : 0-50000 Lux in3 Ranges

1 50

65 Mobile Charger with Multi Pin connector

10 500

66 Screw Driver Adjustable Torque : 1-5kgf.cm Torque Indication

1 50

67 Rehostat 10 ohm, 5 A 2 100

68 Magnifier with illimunation lamp

Glass Lens ( Magnifier ) 3.5 Inch with flourescentillumination

5 250

69 Wrist Band ESD Safe 10 500

Total Cost Inclusive of all taxes (in Figures)

Total Cost (In Words)

B. Consumables

Sr. No.

Name Of The Item Specification Qty Required per Centre

Total Qty. for 50 Centres (C)

Unit Rate inclusive of all taxes and Warranty (D)

Total Amount including all Taxes (C X D)

1 Hookup Wire – 90 Meter Length Bundle

24 SWG 2 100

2 Insulated Connecting Wire (Red, Yellow, Blue, White, Grey, Brown, Black, Green, Orange)

14/36 (90 Meter Length Bundle)

9 450 (1 Each) (50 each)

3 Phenolic General Purpose PCB

6”x 4” size 40 2000

4 Multimeter Battery 9 V 20 1000

5 Main Lead 3 Core 2 Amp Rating 10 500

6 Fuse Holder 20mm 20 1000

7 Glass Fuse 20mm 100 m Amp 10 500




11 Hexa Blade 8” Size 40 2000

12 Machine Screw 1/8 " 100 5000

13 Machine Screw 1/4 " 100 5000

14 Soldering Flux Small Box 40 2000

15 Sand Paper Wood Type 40 2000

16 Safety Glove – pairs 5 250

17 Isopropyl Alcohol for PCB Cleaning

1 litre packing

2 100

18 Silicon Glue Stick Suitable for Glue Gun

10 500

19 Regulator LM 7805 T0220 80 4000

20 Solder Wire Roll Lead Free, 50 gram Packing

40 2000





21 Capacitor 100uf/16V, 1000uf/16V, 470uf/16V,

Electrolytic 150 7500 (50 each) (2500

each)

22 Diode IN 4007 400 20000

23 LED 5mm (RED) 40 2000

24 LED 5mm (GREEN)

40 2000

25 White LEDs 5 mm 200 10000

26 White LEDs 1W(matka type)

200 10000

27 SPST Switch (Toggle SW)

5 AMP 40 2000

28 DPST Switch 5 Amp 10 500

29 TACT Switches 100 5000

30 Slide Switch – SPDT 3 position 40 2000

31 Male Berg Strip 40 pin, Pitch 100 mils

40 2000

32 Female Berg Strip 40 pin, Pitch 100 mils

40 2000

33 Resistances (10 Ohm, 22 Ohm, 33 Ohm, 47 Ohm, 100 Ohm, 220 Ohm,270 Ohm,330 Ohm, 470 Ohm, 560 Ohm, 620 Ohm, 1 K Ohm, 1.5k Ohm, 2.2 K Ohm, 3.3 K Ohm, 4.7 K Ohm, 5.1 K Ohm, 6.8 K Ohm, 10 K Ohm, 22 K Ohm, 33 K Ohm, 47 K Ohm, 68 K Ohm, 100 K Ohm, 220 K Ohm, 330 K Ohm, 470 K Ohm)

¼ W, 5% 2700 135000 (100 each) (5000

each)

34 Variable Resistance - (1k,2k,5k,10k,100k)

Preset ( Screw type)

100 5000 (20 Each) (1000

each)

35 Relays (Sugar Cube) 6V, SPDT (Contact Rating 7A/240 V AC)

40 2000

36 Transistor BC 547 100 5000

37 Transistor IRF Z44 40 2000

38 Transformer 6-0-6V, 1 Amp

10 500

39 Heat Sink For T0220 Package

40 2000

40 Heat Sink Compound Small Box 1 50

41 Sealed Lead Acid Battery

4 V- 1 AH 20 1000

42 Reference Voltage Source TL431

2.5V 40 2000

43 LDR 100 5000



44 Mobile Pin Socket Female (Round Small Pin – like Nokia mobile)

40 2000

45 Nut Bolt For Dish fixing

20 1000

Total Cost inclusive of all taxes (in Figures)

Total Cost inclusive of all taxes (in Words)

I/we hereby undertake that all the terms and conditions, specification, requirement have been

carefully read and nothing has been concealed.

(Signature)

Seal



Annexure-1

List of 50 Centres

Sr.

No.

Centre

Code

Name of CABA-MDTP Centre with Phone, Fax, Mobile & Email

ID

Bihar

1. 1 1328 ShriHumayun Ansari, Centre Incharge,NalandaSamajSewa

Ashram,MohallaChajjoo, Naseerpur, P.O. Bihar Sharif,Dist. Nalanda -

803101 (Bihar)

Mob: 09708966125, 09934048612

Email: [email protected]

2. 2 1334 Dr. Syed Abdul Aziz Salfi, Centre Incharge,DarulUloomAhmadiaSalafia,

Laheriasarai,Dist. Darbhanga - 846001 (Bihar).Ph. No.: 06272-325213-

Ehteshamul Haque (Supervisor) Mob: 09234733379, 09905873471


3. 3 1340 Md. A.Haque, Centre Incharge,Madrasa Islamia Arabia, 27Jama

Masjid, Sitamarhi - 84403302 (Bihar).

Ph. No.: 06226-250259, 250486 Fax: 06226-253051

Mob: 09431209555 (Secr.), 09631431802 (


[email protected]

4. 4 1319 Mr. Mohd. ArshadMadni, Centre Incharge,Jamia Imam IbnTaimiya,At

& P.O. Chandanbara, Via K. Chainpur, Dist. East Champaran - 845312

(Bihar).

Ph. No.: 06250-82249, 240088

Mob: 09431032739, 9472091779, 9661002794


5. 1353 Mr. Mushtaque Ahmad, Principal,DarulUloomRizvia,P.O. Bara

Chakia,Dist. East Champaran - 845412 (Bihar).

Ph. No.: 06257-243571 Mob: 09199856140


6. 1361 Mr. Md. ZakirHussain, Centre Incharge,Simna Public School,At-

Tahirpur, Po+Via-Salmari, Ps-Azamnagar,Katihar - 855113 (Bihar).

Ph. No.: 06451-228316 Mob: 08294370259










7. 7 1362 Mr. Zulfaquar Ahmad Ashrafi, Centre

Incharge,MadrasaNasiriaAshrafiaPanasi,

VPO: Panasi via Tayabpur, Kishanganj - 855117 (Bihar).

Mob: 09873889586


8. 8 1363 Mr. Abdul Quadir Shams, Centre Incharge,

Dawatul Quran Educational and Welfare Trust,At + P.O. DubaTaran,

Baluwa Road,Campus JamiaDawatul Quran, FetkiChowk,Araria -

854311 (Bihar).

Ph. No.: 06453-2226481

Mob:, 09711169021


9. 1

0

1403 Mr. Khalil Ahmed, Centre Incharge,

CCTC, BachchonKaGhar,5028, Darya Ganj,

New Delhi - 110002.

Ph. No.: 23242239, 23278795

Mob: 9868034309 - Faculty (Mr. Faiz Ahmed)

10. 1

1

1429 Mr. R.P. Shukla, Centre Incharge,

GurukulSamajVikasSanstha,C-14/1, Ramgarh, Jahangir Puri,

Behind Bank of Baroda,Delhi - 110033.

Ph .No.: 27642010, 27642011 Mob: 09654941021, 9811666251


11. 1

2

1430 Mr. Farid Ahmad, Chairman,

Minorities Welfare Foundation,

1516, 1st Floor, KalanMahal,

Pataudi House, Darya Ganj,

New Delhi - 110002.

Ph. No.: 23255091, 23287209 Mob: 09212512381, 09873715091

[email protected]

Jharkhand

12. 1

3

1602 Mr. TariqueSajjad, Center Incharge,

Sajjad Institute of Information Technology,

G.K. Market, 1st Floor, KantaToliChowk,

P.O. KantaToli, Ranchi - 834001 (Jharkhand).Ph. No.: 0651-2530522,

2532060Mob: 09431171130

Email: [email protected], [email protected]

13. 1

4

1607 Mr. IntekhabAlam, Centre Incharge,

Bright Career Coaching Institute,

L.B. Road, Chitarpur - 825101,

Dist. Ramgarh (Jharkhand).

Mob: 09934343356, 09334360114










14. 1

5

1609 Mr. Md. Afroz, Centre Incharge,

Infotech Education Centre,

Karbala Road, Sultan Nagar, Chas,

Bokaro Steel City - 827013 (Jharkhand).

Mob: 08235215267, 09953002691


Jammu & Kashmir

15. 1702 Mrs. Zahir Mir, Centre Incharge,

Eve‟s Cyber IT School,, Near Ghousia Hospital,

Khanyar, Srinagar – 190002 (J&K)

Mob: 09419028811


16. 1

7

1706 Mr. G.Q. Bulla, Centre Incharge,

Shah-I-Hamdan Computer Education Centre,UnderSopore Congress

Trust, Near IqbalPark,Shah Abad, Sopore - 193201 (J&K).Ph. No:

01954-225018 Mob: 09419524683-Zafar Ahmed Bakht

C.I.- 9419602103


17. 1

8

1707 Mr. Bashir Ahmad Baba, Centre Incharge,

Sheikh-Ul-Alam Institute of Information &

Technology, Charar-e-Sharif,

Teh: Chardora - 191112, Dist. Budgam (J&K).

Ph. No.: 01951-253308 Mob: 09419035801-Centre Incharge,

09858486580


18. 1

9

1715 Mr. Vijay Kumar Sahani, Centre Incharge,

National Institute for Technical Trainings (NITT),3-A, Pvt. Opp. Church,

Gandhi Nagar,Jammu - 180004.

Ph. No.: 0191-2433765

Mob: 09419104591, 09419261304


19. 2

0

1719 Mr. BaryamMunde, Centre Incharge,

Regional Institute of Management &

Computer Sciences, H.O. Dr. Jasrotia Children Hospital, II Floor,

ShaheediChowk,Kathua - 184101 (J&K).

Mob: 09419108380, 09419108083


20. 2

1

1727 Mr. Fayaz Ahmed Gannai, Centre Incharge,

Urdu Calligraphy Centre (NCPUL),

Bandipora College of information Technology,Urdu Complex, Under

The Management ofCitizen Institute of Educational

Training,MainChowkBandipore, Dist. Bandipora - 193502 (J&K).Ph.

No.: 01957-211091, Residence: 01957-225577 Mob:

09797025629Email: [email protected]











21. 2

2

1729 Mr. Mukhtar Ahmad Bhat, Centre Incharge,All India AASRA

Development & Research Centre, NusratBuilding,Old K.M.D.

Adda,Anantnag - 192101 (J&K).Ph. No.: 01932-225269, Residence:

01932-222970Mob: 09419532040


[email protected]

22. 2

4

1726 Mr. Firdos Ahmad Shah, Centre Incharge,

International Computer Institute (ICI),

BohriKadal, Srinagar - 190001 (J&K). Mob: 09086685191-Centre Incharge,

09796134057-Asma Zafar (Faculty)


23. 2

5

1741 Ms. BhinishShakeel, Centre Incharge, Research Institute of Information Technology (RIIT), Al-Hassan Plaza,

Near Town Hall,

Budgam - 191111 (J&K). Ph. No.: 01951-212026

Mob: 09419111777-C.I. Husband, 09858074224-Faculty,

09906491577-Ishtiyaq Ahmed (Faculty)


24. 2

8

1783 Mr. JavidReyazSidiqi, President,

Waris Institute of Computer Education,

Run by Waris Organization For Rehabilitation and Development,

Nagam, Tehsil: Chadoora, Dist. Budgam - 191113 (J&K).

Mob: 09205153289, 09018262013


25. 2

6

1769 Mr. Nisar Ahmad Bhat, Centre Incharge,

Kirmania Institute of IT, Bakto Complex, Central Market, Beehama,

Near Mobile Towers,

Ganderbal - 191201 (J&K).

Ph. No.: 0194-2416115

Mob: 09797119987, 09596202409-C.I.


26. 2

7

1771 Mr. Eijaz Ahmad Khan, Centre In charge,

Global Institute of Technology,

Under J & K Rural Welfare Institution,

Near BSNL Exchange, Beerwah,

Budgam-193411(J&K)

Mob: 09796732880











27. 2

9

1784 Mr. Afroz Ahmad Mir, Chief Functionary,

Tendril Institute of I.T. (TIIT),

Run by Tendril Educational Trust,

Chanapora, Srinagar - 190015 (J&K).

Ph. No.: 0194-2433999

Mob: 09906703045


28. 3

0

1724 Mr. RoufShafi, Centre Incharge, National Institute of Computer Education (NICE), Under the Management of Kashmir SarhadiTariqatiIdara, National Highway, Umar Abad,HMT Srinagar - 190012 (J&K). Ph. No.: 0194-2496713 Fax: 0194-2433404 Mob: 09906532250 Email: [email protected]

29. 1785 Ms. Ambrin, General Secretary,

Human Welfare Organization (NGO),

SatrathooMohalla, Balhama,

Srinagar - 191101 (J&K).

Mob: 08803306330


30. 1758 Mr. Sheikh Manzoor, Centre Incharge,

Voluntary Organisation on Environmental

and Socio-Economic Planning,

H.O. Taj Building, Opp. D.C. Office,

LalChowk, Anantnag - 192101 (J&K).

Mob: 09797118720, 09419008665


31. 1774 Mr. Abdul Razaq, Incharge,

Sadhbhavana Information Technology,

Under Operation Sadhbhavana,

Safapora, Manasbal, Tehsil: Lar,

Dist. Ganderbal - 193504 (J&K).

Ph. No.: 01954-230340

Mob: 09858469226, 09906746271


32. 1703

Mr. Imtiaz Ahmad, Centre Incharge,

Comtech Institute of Technology under

Comtech IT Educational Trust,

Shah Complex, Near Petrol Pump,

Opp. Police Station, N.H. Road,

Baramulla - 193101 (J&K)

P.No. 01952-235166-C.I., Mob: CEO- 09419432294, 09796727430


Uttar Pradesh









33. 3

1

2511 Dr. Mohammad Anees Khan, Principal, Shibli National College, Azamgarh City, Azamgarh - 276001 (U.P.). Ph. No.: 05462-227879, Mob: 09936380775-09919770018-Samiuddin (Jr. Faculty) Email: [email protected] [email protected], [email protected]

34. 3

2

2539 Mr. Abdul Muttalib, Centre Incharge,

AllamaFazl-e-HaqKhairAbadi Educational Society,11/96,

MaqbaraGwaltoli, Kanpur - 208001 (U.P.).

Ph. No.: 0512-2555147

Mob: 09794898786-Centre Incharge,


35. 3

3

2541 Mr. A.M. GulzarQasmi, Centre Incharge,

MAM Institute of Information Technology,

Gulzar-e-Hussainia Educational Society,

Ajrara - 245206, Dist. Meerut (U.P.).

Ph. No.: 95121-2448023, 2448055

Fax: 95121-2448055, Mob: 09412706634-Centre Incharge,

09837582390-Email: [email protected],

[email protected]

36. 3

4

2546 Mr. M. Tariq Shamsi, Centre Incharge,

Shamsi Institute of Information Technology, Under Management of

Muslim Taleemi Society, Madarsa Arabia Qurania, 206, KatraSewa

Kali,Etawah - 206001 (U.P.).

Ph. No.: 05688-258461Fax: 05688-251025

Mob: 09412349879-Supervisor, 09219077233


37. 3

5

2555 Shri Syed Mohd. Naiem, Centre Incharge,

HamidiyaIslamia School Society, Saqlainabad, National Highway-76,

Rath Road, Panwari,Dist. Mahoba - 210429 (U.P.).Ph. No.: 05281-

242447, 242086, Mob: 09450273249, 09793792249


38. 3

6

2562 Mr. K.M. Amil, Centre Incharge,

Kainat Institute of Information Technology,

Under Science aurKainatSoceity of India,

Near Petrol Pump &MandiSamiti,

BadaunDarwaza, Delhi Hasanpur Road,

Sambhal - 244302, Dist. Moradabad (U.P.).

Ph. No.: 05923-231056,

011-26315721-Secretary (Mr. K. M. Rafi)

Mob: 09917450757-Supervisor (Mr. K.M. Faheem), 09837910359-

Centre Incharge












39. 3

7

2574 Mr. Tajammul Husain, Centre Incharge,

Warsi Higher Secondary School,Warsi Information Technology

Institute,Qaziur, Afzalpurwari, Sirathu,

Kaushambi - 212217 (U.P.).

Mob: 09415321285-C.I., 09415809059


40. 3

9

4501 The Centre Incharge,

Rajiv Gandhi Computer Shiksha Kendra,

Amar Nagar, Kanpur Road,Raebareli - 229001 (U.P.).

Ph. No.: 0535-2210607, 2210608 Mob: 09415046718

Email: [email protected] [email protected]

41. 4

2

4505 Mr. MirzaArif Beg, President,

Maulana Azad Educational Society,

Anjanshaheed, Tehsil-Sagri,Dist. Azamgarh (U.P.).

Ph.: 05462-266786

Mob: 8382950978, 08009275595-Ms. Shirin


42. 4

3

4509 Dr. Ahmad MujtabaSiddiqui, Jt. Secretary,

Al-Barkaat School, Run by Al-Barkaat Educational Society,P.O. CDF,

Anoopshahr Road,Near Jamalpur Railway Crossing,

Aligarh - 202122 (U.P.).Ph. No.: 0571-3299871

Mob: 09359146873


43. 4

4

4510 Mr. Imran Ahmad,

Al-Noor School, Run by Mamba-Ul-Uloom Education Society, Pahasu

House, Near Tibbiya College, Civil Lines,

Aligarh - 202001 (U.P.).

Ph. No.: 0571-2402500 Mob: 9897920730, 9045236001


44. 4

5

4511 Mr. NasimRaza,

Minority Development Society,Amjadi Road, Bara Gaon,

Ghosi - 275304, Dist. Mau (U.P.).

Ph. No.: 05461-222429

Mob: 09335209598,9935383814, 9616867647,


45. 4

6

4523 Mr. Anwar Abbas, Centre Incharge,

GurukulShikshaEvamGraminVikasSansthan,

459/786, MehtabBagh, Opp. Shish MahalTalab,

DurgaPuriMarg, MohniPurwaChowk,

Lucknow - 226003 (U.P.).

Ph. No.: 0522-2253997 Mob: 09335904040, 08400730786,

08896730786














46. 4

7

2532 Mr. Sharif Ahmad, Centre Incharge,

NCPUL Computer Centre,Islamia College of Commerce,

Under Islamia Education Society, Buxi Bazar,

Gorakhpur - 273001 (U.P.).

Ph. No.: 0551-2345786

Mob:9935524372, 9415192929, 9044395595 9415858692

Fax: 0551-2349211


47. 4

8

4516 Ms. KiranYadav, President,

AnubhutiSewaSamiti,MohallaSarafa,

Patiyali - 207247 (U.P.).

Ph. No.: 05740-252470

Mob: 9319291919, 09958222106


48. 5

0

4532 Mr. Ashok Verma, Centre Incharge,

Ashok SewaSansthan,VPO: Kusela, Maholi,

Sitapur - 261141 (U.P.).

Mob: 8756509146, 09839717671


49. 4515 Ms. AyashaParveen, President,

RabiyaMahilaSevaSansthan,

VPO: Baheri, Dist. Ballia - 277001 (U.P.).

Mob: 09838179295, 9918470198, 9935479636,


50. 4517 Ms. ShaguftaMariyamAbbasi,Centre Incharge,

S.T. Educational Society,Rasoolpur, Gorakhnath,

Gorakhpur - 273015 (U.P.).

Ph. No.: 0551-22585226

Mob: 08574667196, 09415691100





