Upload
others
View
3
Download
0
Embed Size (px)
Citation preview
Fa stener Referenc e G uideM ea suring Threa ded Fa steners (length)
M ea suring Threa ds
Hea d Sty les
To Selec t Phillips Driv er Sty leDriv er Sty les
Fa stener Identifier (D=Dia m eter)
Fla t Fla tUnderc ut
Ov a l Ov a lUnderc ut
Round Fillister Pa n Binding BindingtUnderc ut
Truss RoundW a sher
Trim m edHex a gon
IndentedHex a gon
Slotted
IndentedHex a gonW a sher
Squa re
A325
G ra de 2 G ra de 5 G ra de 8
Hea d M a rk ings of Fa steners
18-8 Sta inlessSteel
316 Sta inlessSteel
A 325Struc tura l
316
Fla t W a sher
Split Loc k W a sher
Hex N ut
A c orn C a p
C oupling
Soc k et C a p
U-Bolt
Step Bolt
Ey ebolt
W ing N ut
Hex Stop N ut
Finish W a sher
Torque W a sher
Fla nge-Loc kW ood Sc rew
D
M a c hine Sc rewO v a l Hea d Slotted
D
M a c hine Sc rewFillister Hea d Slotted
D
Plow BoltD
Dry w a ll Sc rewD
C a p Sc rewD
La g Sc rew
D
Set Sc rewN utDD
M a c hine Sc rewFla t hea d slotted
D
StudD
Sheet M eta lSc rew
D
C a rria ge Sc rewD
Squa re N ut
Ex terna l ToothLoc k W a sher
Tee N ut
Interna l ToothLoc k W a sher
Hex C a stle N ut
Elev a tor Bolt
Founda tionHook Bolt
#990030
1| Revision Date: 6/23/16 | Revised by: EM
Fastener Reference Guide
2| Revision Date: 6/23/16 | Revised by: EM
HARDWARE ABBREVIATIONS KEY
All screws should have the same information in the Description field. Use the key below to determine if the head type, tool style, size, material, and hardness are accurate.
SCREW;SH;M8X1.25PX45L-30L;HS;BZN;G12.9;
Head Type – This is the type of head on the screw. Commonly used types are: BH – Button Head FH – Flat Head Round – Round Head SH or HS – Socket Head TRH or TRHW – Truss Head
CB – Carriage Head HH – Hex Head SET – Set Screw TH – Thin Head
Size – This is the screw size, thread pitch, and length. M3 – M12 – This is the size of the screw and is normally the first dimension listed. While most screws are metric, it is possible you will see a standard screw listed (example: 3/8”). 7P – 1.75P – This is the pitch of the screw threads. This is normally consistent and does not need to be checked. The pitch will not be listed on all screws, especially smaller sizes. Length – This is the total length of the screw minus the head in millimeters. If there are two numbers here (as seen in the example description: 45L-30L), it indicates the screw is only partially threaded. The example indicates a screw that is 45mm in length with threads on only 30mm of that length. Most partial thread screws will also be labeled with P-T.
Drive Style – This is the tool style that should be used to remove the screw. HS – Hex Socket HE – Hex Head
PH – Phillips Head
Thread Style – This is the style of the threads. This will only be called out for special threading. MT – Machine Thread TC – Thread Cutting
SM – Sheet Metal
Material – This is the material used to make the screw. The material will either be black or silver, both of which have several variations.
BZN, BED, BAN, BOX – These are black versions of screws CHM, CRMO, ZINC, ZN, SS, WZN – These are silver versions of screws
Hardness – This is the material hardness of the screw. G8.8 or G12.9 – We normally use 3 different hardness settings = G8.8, G12.9, and non-specific. If hardness is called out in the description, the screw should have the hardness stamped on the head.
Head Type Size Drive Style Material Hardness