F11.11 CHRONO PERIMETER LOCKING SETS - …€¦ · CHRONO PERIMETER LOCKING SETS F11.11 ... • Totally clampable system for project-out windows based on the CHRONO turn and ... drawing

CHRONO PERIMETER LOCKING SETS

F11.11

01.06.2018

F11

PROJECT-OUT WINDOWSAND TOP HUNG WINDOWS

Waregemstraat 5 - 9870 Zulte - Belgium - T. +32 9 388 88 81 - F. +32 9 388 88 21 - [email protected] - www.sobinco.com

F11.11.02 PROJECT-OUT WINDOWS


F11.11

CONTENTS

1. General characteristics........................................................F11.11.031.1. Perimeter locking F11.11.031.2. Friction hinges F11.11.03

2. Base sets ..............................................................................F11.11.042.1. Base set n° 60141 F11.11.042.2. Base set n° 60142 F11.11.05

3. Centre locking sets ..............................................................F11.11.063.1. Horizontal: n° 30140-800 and 4208-123 F11.11.063.2. Vertical: n° 20140-35 and 30140-800 F11.11.07

4. Selection of rods n° 35000-... .............................................F11.11.084.1. With base set n° 60141 F11.11.084.2. With base set n° 60142 F11.11.09

5. Wedge positions ................................................................... F11.11.105.1. With base set n° 60141 F11.11.105.2. With base set n° 60142 F11.11.11

6. Installation instructions ......................................................F11.11.126.1. With base set n° 60141 F11.11.126.2. With base set n° 60142 F11.11.13

7. Order tables ......................................................................... F11.11.147.1. With base set 60141 (handle 30000 or 4000) F11.11.147.2. With base set 60142 (handle 502 or 5020) F11.11.14

8. General information .............................................................F11.11.15

PROJECT-OUT WINDOWS F11.11.03


F11.11

1. General characteristics1.1. Perimeter locking

• Totally clampable system for project-out windows based on the Chrono turn and tilt technology.

• We have 2 base sets which vary according to the profile design: - N° 60141: with handle mounted on a horizontal profile surface: type 4000 or 30000. - N° 60142: with handle mounted on a vertical profile surface: type 502 or 5020.

• Windows higher and/or wider than 1200 mm must be provided with an additional centre locking set.

• The handle and the friction hinges are not included in the base set.

• All parts are made of non-corroding materials.

• Size range: - vent width FFb: 600-2400 mm (with set 60141) - vent width FFb: 572-2400 mm (with set 60142) - vent height: 300-2400 mm - vent weight: max. 180 kg

• N.B.: the minimum and maximum vent width, vent height and vent weight depend on the type of friction hinge.

• Dimensions out of standard range on request!

1.2. Friction hinges• The perimeter locking set is suitable to apply with the friction hinges series P691-... which are selected

in accordance with the width, the height and the weight of the vent. See table below. Advice should be sought from Sobinco when the sizes of your window differ from these dimensions.

• The maximum vent weight should never be exceeded!

• The vent movement must always be checked because there’s a chance that the vent will hit the frame when opening the window. The smaller the hinge, the bigger the risk. It’s sufficient to provide us a CAD drawing of the profile cross sections.

• For windows with a vent width of more than 100 kg, we recommend to use an additional window stay with friction device.

• We refer to chapter F11.13 for more details regarding the hinges.

Order code per pair

Hinge length L (mm)

Min/max vent height (mm)

Max vent weight (kg)

Opening angle A (+/- 2.5°)

TOP-HUNG WINDOWSP691-255 262 267/640 40 50°P691-305 313 640/800 50 50°P691-406V 415 800/1100 65 50°P691-559 567 1100/1500 100 45°P691-559V 570.5 1500/2000 100 20°P691-660 682.5 2000/2500 100 20°P691-660R 716.5 2000/2500 180 20°



F11.11

2. Base sets2.1. Base set n° 60141

Vent width FFb = 600-1200 mmVent height FFh = 300-1200 mm

• Profile dimensions: One system suitable for sections with frame groove width from 10 to 14 mm.

601411 10000-700 connection piece2 20000-620 bolt2 30000-600 vent run on rest2 30000-690 screw for handle2 30140-800 wedge

Friction hingeP691-...(left hand)

Friction hingeP691-...(right hand)

or Only for positioning of 20000-620. Remove after assembly.

Only for positioning of 20000-620. Remove after assembly.

Fb or Fh

FFb or FFh



F11.11

2.2. Base set n° 60142

Vent width FFb = 572-1200 mmVent height FFh = 300-1200 mm

• Profile dimensions: One system suitable for sections with frame groove width from 10 to 14 mm.

601421 4600-232.2 drive pin2 20000-620 bolt1 24000-701-1 connection piece2 30000-600 vent run on rest2 30140-800 wedge2 30300-701-2 fixing piece2 M5x35 DIN965 screw2 M5 UFO40 rivnut

Friction hingeP691-...(left hand)

Friction hingeP691-...(right hand)

or



Fb or Fh

FFb or FFh



F11.11

3. Centre locking sets

3.1. Horizontal: n° 30140-800 and 4208-123

Vent width FFb = 1200-1800 mm

• Windows with vent width from 1200 to 1800 mm require an additional wedge n° 30140-800 at the bottom and a pull-in wedge n° 4208-123 at the top.

Vent width FFb = 1800-2400 mm

• Windows with vent width from 1801 to 2400 mm require an additional wedge n° 30140-800 at the bottom and an additional pull-in wedge n° 4208-123 at the top.

60141 or 60142+

1 30140-800 wedge+

1 4208-123 pull-in wedge

or

or

60141 or 60142+

1 30140-800 wedge1 4208-123 pull-in wedge

1 30140-800 wedge

1 4208-123 pull-in wedge



F11.11

3.2. Vertical: n° 20140-35 and 30140-800

Vent height FFh Vent height FFh= 1201-1800 mm = 1801-2400 mm

• Windows with vent height from 1201 to 1800 mm require a centre locking set n° 20140-35.

• Windows with vent height from 1801 to 2400 mm require 2 additional wedges n° 30140-800.

60141 or 60142+

20140-352 30000-515 corner transmission2 30140-800 wedge

60141 or 60142+

20140-35+

2 30140-800 wedge



F11.11

4. Selection of rods n° 35000-...4.1. With base set n° 60141

• The system consists of 11 transmission rods with different lengths: 35000-100, 35000-150, ... .

• The adjustment range of each rod is 50 mm.



F11.11

4.2. With base set n° 60142• The system consists of 11 transmission rods with different lengths: 35000-100, 35000-150, ... .

• The adjustment range of each rod is 50 mm.



F11.11

5. Wedge positions5.1. With base set n° 60141

• The positioning of the wedges can be carried out very accurately and fast by means of a jig set n° 35000-950.• Note: the drawing below only shows the situation when

the handle is in the middle.

• Jig set n° 35000-950.

• Important! Tighten all clamping screws (grub screws 2.5 mm) of the frame parts with a force of 1.75 Nm +/-0.25 Nm.

Green

Red

Blue

jig

jig

jig

jig

jig

jig



F11.11

5.2. With base set n° 60142• Note: the drawing below only shows the situation when the handle is in the middle (A = FFb/2).• Important! Tighten all clamping screws (grub screws 2.5 mm) of the frame parts with a force of

1.75 Nm +/-0.25 Nm.



F11.11

6. Installation instructions6.1. With base set n° 60141

or

or

WEDGES FFb=600-1200 FFb=1201-1800 FFb=1801-2400FFh=300-1200 9, 11 9, 10, 11, 16, 19 8, 9, 10, 11, 16, 17,

18, 19FFh=1201-1800 9, 11, 13, 15 9, 10, 11, 13, 15, 16,

198, 9, 10, 11, 13, 15, 16, 17, 18, 19

FFh=1801-2400 9, 11, 12, 13, 14, 15 9, 10, 11, 12, 13, 14, 15, 16, 19

8, 9, 10, 11, 12, 13, 14, 15, 16, 17, 18, 19



F11.11

6.2. With base set n° 60142

or

or

WEDGES FFb=572-1200 FFb=1201-1800 FFb=1801-2400FFh=300-1200 12, 14 11, 12, 14, 20, 21 11, 12, 13, 14, 19, 20,

21, 22FFh=1201-1800 12, 14, 16, 18 11, 12, 14, 16, 18,

20, 2111, 12, 13, 14, 16, 18, 19, 20, 21, 22

FFh=1801-2400 12, 14, 15, 16, 17, 18 11, 12, 14, 15, 16, 17, 18, 20, 21

11, 12, 13, 14, 15, 16, 17, 18, 19, 20, 21, 22



F11.11

7. Order tables7.1. With base set 60141 (handle 30000 or 4000)

7.2. With base set 60142 (handle 502 or 5020)

Order example:A project-out window with vent width (FFb) 1300 mm and vent height (FFh) 1400 mm with handle 30000-659T with a glass thickness of 10 mm and a weight of 25 kg/m2.

Fittings to order: - 1x P691-559 (see chapter F11.13) - 1x 30000-659T - 1x 60141 - 1x 20140-35 - 1x 30140-800 - 1x 4208-123Rods: - 2x 30000-365 - 2x 30000-400

FFb=600-1200 FFb=1201-1800 FFb=1800-2400

FFh=300-1200

30000-659T+ 60141

30000-659T+ 60141+ 30140-800+ 4208-123

30000-659T+ 60141+ 2x 30140-800+ 2x 4208-123

FFh=1201-1800

30000-659T+ 60141+ 20140-35

30000-659T+ 60141+ 20140-35+ 30140-800+ 4208-123

30000-659T+ 60141+ 20140-35+ 2x 30140-800+ 2x 4208-123

FFh=1801-2400

30000-659T+ 60141+ 20140-35+ 2x 30140-800

30000-659T+ 60141+ 20140-35+ 3x 30140-800+ 4208-123

30000-659T+ 60141+ 20140-35+ 2x 30140-800+ 2x 4208-123

+ TRANSMISSION RODS (in accordance with the vent dimensions)

FFb=572-1200 FFb=1201-1800 FFb=1800-2400

FFh=300-1200

502-..+ 60142

502-..+ 60142+ 30140-800+ 4208-123

502-..+ 60142+ 2x 30140-800+ 2x 4208-123

FFh=1201-1800

502-..+ 60142+ 20140-35

502-..+ 60142+ 20140-35+ 30140-800+ 4208-123

502-..+ 60142+ 20140-35+ 2x 30140-800+ 2x 4208-123

FFh=1801-2400

502-..+ 60142+ 20140-35+ 2x 30140-800

502-..+ 60142+ 20140-35+ 3x 30140-800+ 4208-123

502-..+ 60142+ 20140-35+ 2x 30140-800+ 2x 4208-123

+ TRANSMISSION RODS (in accordance with the vent dimensions)



F11.11

8. General information• Attention! The maximum dimensions, for which the project-out systems n° 60141 and n° 60142 can be

used, are determined by the type of friction hinge used. Technical advice should be sought when the sizes of your window differ from these dimensions.

• The project-out system is made of non-corroding materials. The set should not be installed in corrosive atmospheres.

• Sobinco cannot be held responsible for the malfunctioning of the project-out system if any non-Sobinco parts are used.

• All parts must be assembled according to the instructions as described in previous pages.

• Surface treatment of vent and frame must take place before assembly of the set, as this will affect the working of the gear.

• Glazing must be in accordance with national standards.

• The window and gear should be kept clean and lubricated in accordance with our maintenance instructions (copy available on request).

Glass thickness without air gap

mm kg/m²10 2512 3014 3516 4018 4520 5022 5524 6026 6528 7030 7532 8034 8536 9038 9540 10042 105



F11.11

Documents

F11.11 CHRONO PERIMETER LOCKING SETS - …€¦ · CHRONO PERIMETER LOCKING SETS F11.11 ... • Totally clampable system for project-out windows based on the CHRONO turn and ... drawing