EXTRUDER PELLETIZING LINES

2

WERNER & PFLEIDERER MODEL KP-92/250 TWIN SCREW EXTRUDER

W&P/COPERION MODEL EGR-250 HOTFACE CUTTER PELLETIZER

DAVIS STANDARD THERMATIC MODEL 60IN60TP1H 6" SINGLE SCREW EXTRUDER

DAVIS STANDARD LINE WATER THROUGH TABLE & BERINGER AIR WIPE DRYER

EXTRUDER PELLETIZING LINESLines may be sold bulk subject to the piecemeal bids

1 – WERNER & PFLEIDERER EXTRUDER PELLETIZING LINE,INCLUDING:

• (1) K TRON BELT FEEDER BLEND INFEED, DC Direct DriveVariable Speed

• (1) SCHENCK ACCU RATE REGRIND FEEDER AUGER, WithProgrammable Feed Rate Control, PPE Vacuum Loader

• (1) WERNER & PFLEIDERER MODEL KP-92/250 TWIN SCREWEXTRUDER, S/N 180978 (1997), 400-HP DC Drive, 3-1/2" Screws,18.1 Ratio, 4-Zone Electric Band Heat, Liquid Cooled, T2-2X5000NMGearbox, Closed Loop Oil System Gearbox, With Water Cooled HeatExchanger, 400-HP Soft Start Drive, With 440 KVA IsolationTransformer, Transition Box Discharge, With Colt-On 7-1/2-HPVacuum Pump System

• (1) W&P PROCESS TECHNOLOGIES INC. MODEL 10000.250MM,250mm 7:1 L/D Single Screw Extruder, S/N 2333-EXT (1997), 200-HP DC Drive, With Soft Start Drive & 220 KVA IsolationTransformer, Process Water Cooled Gearbox, 70" Screw, ElectricBand Heat, Water Cooled

• (1) W&P/COPERION MODEL EGR-250 HOT FACE CUTTER PELLETIZER, S/N 2050 2027 (2007), 36" Diameter 3-Blade CutterHead, 11.0 KW Cutter Head Drive, With Allen Bradley Power FlexProgrammable Frequency Drive Control, Die Plate, Floor ChuteDischarge

• (1) LIQUID RADIATOR COOLED FORCED AIR HEAT EXCHANGER• (1) GASHO ASSOCIATES 30-HP POSITIVE DISPLACEMENT

BLOWER (Outside Roof Mounted)• (1) ROOF MOUNTED RECEIVER CYCLONE, Gravity Discharge• (1) W&P AIR BED DRYER, MODEL & S/N NA, Roof Mounted Ventra

Pro Model E355/56-50 16.6 KW Blower, S/N 58606/1-98, Dryer BedSize 21-1/2" x 9', Start-Up Bypass Valve, Roof Mounted PelletBaghouse

• (1) SWECO VIBRO-ENERGY MODEL X548C66, 48" VIBRATORYSEPARATOR/SIZER, S/N 752039A300, 2-1/2-HP, Stainless Steel, 2 Screen Decks, 1/4" Hole Top Screen, 3" Non-Perforated Center/2"Non-Perforated Outside, 10mm Wire Mesh Fines Screen

• (1) FOX VENTURI, WITH 6" FORCED AIR BLOWPIPE & GASHOASSOCIATES 30-HP POSITIVE DISPLACEMENT BLOWER(Outside Roof Mounted)

• (1) ROOF MOUNTED RECEIVER CYCLONE, GRAVITYDISCHARGE

• (1) MATERIAL LOAD-OUT HOPPER, Stand Mounted, Gravity Infeed& Outfeed

• (1) ELECTRONIC PLATFORM WEIGH SCALE, 60" x 60" x 5000-Lb.Mettler Toledo Panther Programmable Readout

• (1) MAIN CONTROL PANEL, Allen Bradley SLC 5-04 PLC, EurothermDigital Heat Controls, Melt Temperature Monitors, Torque & RPMMeters, Complete Line Interlock System, Push Button & SwitchControls

1 – DAVIS STANDARD 6" EXTRUDER PELLETIZING LINEINCLUDING:

• (1) MESA EQUIPMENT 10-HP VACUUM PUMP, S/N NA,Sutorbilt Model GACMDPA Vacuum/Blower (Outside by Silos)

• (1) MAC RECEIVER FILTER HOPPER, S/N NA, Vacuum Fed,Top Pneumatic Manifold, Filter Bags, Hopper Vibrator,Pneumatic Knife Gate Discharge

• (1) SCHENCK ACCU RATE AUGER FEEDER, WithProgrammable Feed Rate Control

• (1) SCHENCK ACCU RATE COLORANT ADDITIVE FEEDER, With Programmable Feed Rate Control

• (1) DAVIS STANDARD THERMATIC MODEL 60IN60TP1H 6"SINGLE SCREW EXTRUDER, S/N U3920 (1997), 300-HPDC Drive Motor, 16' Screw Length, Electric Band Heaters,Liquid Cooled, With Heat Exchanger, 17.21:1 Gearbox Ratio,Closed Loop Oil Cooled Gearbox, With Water Cooled HeatExchanger, Reliance Electric Soft Start Drive, 330 KVAIsolation Transformer, Control Panel, With Ogden Digital HeatControllers (6-Zone Barrel, 4-Zone Die Head), Solid StateTemperature Control Blocks (New Barrel & Refurbished Screw2008)

• (1) DIE HEAD, (2) DIE PLATES, SCREEN PACKS, 21" WIDESTRAND TYPE HEAD

• (1) WATER TROUGH TABLE, Stainless Steel, 10' Long x 24"Wide x 12" High, Closed Loop Cooling Water RecirculationSystem, With Transfer Pump, Caster Mounted

• (1) BERINGER AIR WIPE DRYER, WITH VACUUM TURBINE, S/N 12D339 (1998)

• (1) CONAIR JETRO MODEL 212 PELLETIZER, S/N 8-120389, 15-HP, 12" Rotor Blades

• (1) AIR BED DRYER, VACUUM RECEIVER HOPPER, 21-1/2" x 5' Bed Size, W&P 15 KW Blower, Outside FinesCollector Silo

• (1) MAC MODEL 560 PKG 7.5-HP VACUUM PUMP, S/N 51925-001-1, Sutorbilt Model GACMDPA Vacuum/Blower (Outside)

• (1) SWECO VIBRO-ENERGY MODEL XS48S88 48" VIBRATORY SEPARATOR/SIZER, S/N 649633-A197, 2-1/2-HP, 2 Screen Decks, Stainless Steel, 1/4" Top ScreenHoles, 10mm Wire Mesh Fines Screen

• (1) WHITLOCK 7.5-HP VACUUM POWER UNIT, S/N 8631181

• (1) MATERIAL LOAD-OUT RECEIVING HOPPER, VacuumFeed, Gravity Discharge, Stand Mounted

• (1) ST REGIS MODEL 106FGS BAGGER, S/N 832003,Mechanical, Off-Line Retractable

• (1) INSCALE MODEL D-44-1-5K ELECTRONIC PLATFORMWEIGHT SCALE, S/N 19545, 48" x 48" x 5000-Lb.Programmable Readout

MIXING LINES • CONTROL SYSTEM • SUPER SACK UNLOAD STATIONS

3

TECHNICAL PROCESS & ENGINEERING FREE ROTOR EXTENDEDCONTINUOUS MIXER & 6" EXTRUDER PELLETIZING LINE

BERLYN 6" SINGLE SCREW EXTRUDER MAC SUPER SACK UNLOAD STATIONS

#4 MAC MODEL 19FRBC14FILTER HOPPER

LITTLEFORD MIXING LINE WORKTANK HOPPERS & FILTERS

METTLER TOLEDO 48" X 48" X 5000-LB.ELECTRONIC WEIGH SCALE

LITTLEFORD MIX LINE HOT OIL HEATER

MAC COMPUTERIZED CONTROL ROOM SYSTEM

Additional Extruder Pelletizing Lines are located on pages 4 & 6 of this brochure.

EXTRUDER PELLETIZING LINESLines may be sold bulk subject to the piecemeal bids

1 – TECHNICAL PROCESS & ENGINEERING SIZE 4 FREEROTOR EXTENDED CONTINUOUS MIXER & 6" EXTRUDERPELLETIZING LINE (4FRE LINE), INCLUDING:

• (1) K-TRAN MODEL K4G 3-COMPONENTBLENDER/FEEDER SYSTEM, (New 2008), ProgrammableTouch Screen Control, With 16 Feeder Capacity, (2) Stainless Steel Pellet Feeder Hoppers Each With LoadCell Scales, Premier Vacuum Loader/Filter System &Pneumatic Knife Gate Discharge, (1) Stainless Steel BlendFeeder, With Premier Vacuum Loader/Filter System, LoadCell Auger & Load Cell Pan Scale, System Mounted onTrolley Retractable Framework System

• (1) WATSON MARLOW MODEL 520U PROGRAMMABLEOIL ADDITIVE PUMP

• (1) T.P. & E SIZE 4 MODEL 4FREIL FREE ROTOREXTENDED CONTINOUOUS TWIN SCREW MIXER, S/N 98A150-M (1998), 200-HP DC Motor, With GE DV300Soft Start Drive (Refurbished 2008), #7 Screw Size, 48"Screw Length, Electric Band Heat, Water Cooled, Air GateRibbon Feeder Discharge, 220 KVA Isolation Transformer

• (1) T.P. & E MODEL 60MPEIL 6" SINGLE SCREWEXTRUDER, S/N 98A150-E, 200-HP DC Drive Motor, WithGE DV300 Soft Start Drive, 6' Screw Length, Die Head,Electric Band Heat, Water Cooled, 220 KVA IsolationTransformer

• (1) MIXER/EXTRUDER CONTROL CABINET, Each, With 2-Zone Digital Heat Controls, Motor Load & Screw SpeedMeters, Push Button Controls

• (1) GALA UNDERWATER PELLETIZER SYSTEM, ExtruderDie Head Mounted Wet Box Cutting Chamber, With PressurizedWater Upflow Discharge, 15-HP Motorized Cutting Head onRetractable Stand, Model 2016-DW Separator/Dryer, S/N982338, Model 140 GPM TWS Hot Water Recirculation Tank,250-Gallon Stainless Steel Tank, With Watlow Electric Heaters,Pelletizer System Control Cabinet, Water Recirculation System,With Pump & Heat Exchanger

• (1) SWECO MODEL US48-C66 VIBRO-ENERGY 48"VIBRATORY SEPARATOR/SIZER, S/N US48-5-81-52,Single Deck, 1/8" Holes, Stainless Steel Screen, CarbonSteel Shell

• (1) MATERIAL LOAD-OUT STATION, With Stand MountedReceiving Hopper, Whitlock 7.5-HP Vacuum Power Unit, In-Ground 72" x 48" x 5000-Lb. Electronic Scale,Programmable Readout

1 – BERLYN 6" EXTRUDER PELLETIZER LINE, INCLUDING:• (1) BERLYN 6" SINGLE SCREW EXTRUDER, S/N 021C516,

300-HP DC Drive, 30:1 L/D Ratio, Lufkin Gearbox (Rebuilt2000), 5-Zone Electric Band Heat, Liquid Cooled, SingleScrew, Feed Hopper, Control Panel, Transformer

• (1) AIR WIPE DRYER• (1) CONAIR PELLETIZER (Parts) NOTE: Line is Disconnected & Stored.

MIXING LINESLines may be sold bulk subject to the piecemeal bids

1 – LITTLEFORD MIXING LINE, INCLUDING:• (2) MAC MODEL 5 X 1 WORK TANKS, S/Ns 97-296-002, NA, Each, With Colt-On

Systems Model 54AVS16-111 Dust Collector/Filter System (Coarse Filter & Fine Filter),Gravity Drop, With Airlock Valves & Pneumatic Knife Gates

• (1) MAC MODEL 5 X 1 WORK TANK, S/N NA, Gravity Drop, With Airlock Valve &Pneumatic Knife Gate

• (1) MAC LEAD ADDITIVE WORK TANK, With Filter System (Not In Use)• (1) MAIN FRAME LOAD CELL WEIGH SCALE STATION FOR OILS & RESINS• (1) STAND-ALONE FILLER LOAD CELL SCALE HOPPER• (1) OIL TANK, With Regulated Fill Valves• (1) LITTLEFORD MODEL K-1200 HEAT MIXER, S/N 405593-3165, 30-HP, Oil Heated,

Jacketed, 30" Diameter x 8' Length Stainless Steel Horizontal Mixing Chamber,Automated, Bottom Center Discharge, With Pneumatic Drop Gate

• (1) HEAT INC. MODEL 550 HEAT MIXER OIL HEATER, S/N 2540, 100 KW• (1) LITTLEFORD MODEL K-1200 COOLER, S/N NA, 30-HP Paddle Drive, Water

Cooled, Jacketed, 30" Diameter x 8' Length Stainless Steel Chamber, Automated, BottomCenter Discharge, With Pneumatic Drop Gate

• (1) METTLER TOLEDO 48" X 48" X 5000-LB. ELECTRONIC WEIGH SCALE, WithProgrammable Readout

1 – MTI MIXING LINE, INCLUDING:• (3) MAC MODEL 5 X 1 WORK HOPPER TANKS, S/Ns NA, Gravity Drop, With Airlock

Valves & Pneumatic Knife Gates, Colt-On Systems Dust Collectors/Filters• (1) MAC MODEL 5 X 1 WORK HOPPER TANK, S/N NA, Gravity Drop, With Airlock Valve

& Pneumatic Knife Gate• (1) LEAD HOPPER/FILTER, With 10-HP Vacuum Blower (Not In Use)• (1) MAC CLAY ADDITIVE WORK HOPPER TANK, With Filter Bag Collector• (4) AUGER FEEDER STATIONS• (1) LOAD CELL WEIGH SCALE HOPPER, Approximately 1000-Lb. Rating, With Air

Bladder, Pneumatic Knife Gate Discharge• (1) RESIN LOAD CELL SCALE HOPPER, With (2) Rotary Airlock Fill Valves, Air Knife

Gates• (1) PLASTISIZER FLUID WEIGH SCALE HOPPER, With Oil Fill Valves• (1) MTI MODEL M850S/K3300 HEAT MIXER, S/N 1247 (1997), 300-HP, Vertical

Stainless Steel Mixing Chamber, Top Fill, Safetronics Solid State Soft Start Motor Control• (1) MTI COOLER, S/N 1247 (1997), 4' x 10' Paddle Blade Chamber, Jacketed, Process

Water Cooled, Air Lock Chamber Door, Bottom Discharge, With Air Gate1 – MTI LINE MATERIAL TRANSFER SYSTEM, 4 HOPPER SYSTEM, INCLUDING:

• (1) #1 PIT MOUNTED RECEIVING HOPPER, Underneath Cooler; Cone Bottom, WithVacuum Port

• (1) #2 MAC MODEL 19FRBC14 FILTER HOPPER, S/N 97-FRBF-09-001, Vacuum Fed,Top Pneumatic Manifold, Filter Bags, Hopper Vibrator, Rotary Airlock Discharge Valve(Roof Mounted)

• (1) #3 MAC HOLDING/RECEIVING HOPPER, Stand Mounted, Gravity Airlock Fed,Bottom Vacuum Discharge, Bin Vibrator

• (1) #4 MAC MODEL 19FRBC14 FILTER HOPPER, S/N 98-FRBF-01-005, Vacuum Fed,Top Pneumatic Manifold, Filter Bags, Hopper Vibrator, Rotary Air Lock, Discharge Valve,(Roof Mounted)

• (1) #1 to #2 VACUUM TRANSFER PUMP; Sutorbilt Type 5MP Model GAEMDPA 15-HPVacuum/Blower Pump, S/N S203362 (Outside on Chiller Pad)

• (1) #3 TO #4 VACUUM TRANSFER PUMP; Sutorbilt Type 4MP Model GACMDPA15-HP Vacuum/Blower Pump, S/N S225831, (Outside on Chiller Pad)

MIXER LINES MASTERCONTROL SYSTEM

1 – MAC COMPUTERIZED CONTROL ROOMSYSTEM (NEW 1997), OPERATED ON WONDERWARE TRADEMARKED/LICENSEDOPERATING SOFTWARE (CUSTOMERLICENSING/SUBSCRIPTION REQUIRED)

• MTI SIDE, With Allen Bradley SLC-500 PLC,Load Cell Scale Controllers, TemperatureMonitors, Chart Recorder

• LITTLEFORD SIDE, With Allen Bradley SLC-5/04 PLC, Load Cell Scale Controllers,Temperature Monitors, Motor Control Panel

• PC CONTROL UNIT, With Display Monitors, (3)On-Floor Operators Stations

BULK MATERIAL STORAGE

2 – DRY RESIN MATERIAL STORAGE SILOS,Welded Carbon Steel, 14' Diameter x 60' High,Top Forced Air Gravity Fed, Cone BottomDischarge, With Rotary Air Lock Valve

1 – COLT-ON SYSTEMS SILO LOADING BLOWER, With Schwitzer Model C466-81 25-HP Positive Displacement Blower, S/N 423/4012

8 – PLASTISIZER OIL STORAGE TANKS,Welded Carbon Steel, 12' Diameter x 15' High,Each With Viking Model KK32V 1-1/2-HP2" Dispensing Pump

SUPER SACK UNLOAD STATIONS

2 – MAC SUPER SACK UNLOAD STATIONS,Each With Self-Contained Dust Collector,Gravity Drop, With Rotary Air Lock Valve(Coarse & Fine Stations)

1 – MAC SUPER SACK VACUUM UNLOAD STATION, Self-Contained Dust Collector

1 – BAG RESIN UNLOAD STATION, Manual Load50-Lb. Bags, Unload Table, Gravity DropHopper, With Rotary Air Lock Valve (M-GradeStation)

1 – SUPER SACK CLAY UNLOAD STATION,Gravity Drop Hopper, With Vacuum Port

1 – MAC MODEL 1LFB-5 25-HP SUPER SACKCLAY FEEDER VACUUM PUMP, S/N99INLF91001, Schwitzer Duro FlowVacuum/Blower Pump (Outside on Chiller Pad)

1 – COARSE, FINE, & M-GRADE STATIONSSHARED BLOWER SYSTEM, Gardner DenverDura Flow Model CGDCABA 25-HPVacuum/Blower Pump, S/N U12431, (Outsideon Transformer Pad)

4

AIR COMPRESSORS • FORKLIFTS • LAB • EXTRUDER PALLETIZING LINES

VIEW OF HYSTER FORKLIFTS TO 4750-LB. CAPACITYINGERSOLL RAND SSR-EP50SE 50-HP ROTARY

SCREW AIR COMPRESSOR

DAVIS STANDARD GEMINI MODEL GP-140-MM LINE #2 CINCINNATI MILACRON MODEL CM 92 HP LINE #6 CINCINNATI MILACRON MODEL TP 140-26-1 LINE #7

Additional Extruder Pelletizing Lines are located on pages 2, 3 & 6 of this brochure.

EXTRUDER PELLETIZER LINESLines may be sold bulk subject to the piecemeal bids

GRANULATORS1 – WORTEX MODEL JC-10L GRANULATOR, S/N F-1383, Opening Size 10" x 20", Screen Holes 3/8", Blade Size 3 – 121 – NELMOR MODEL G1215P1 GRANULATOR, S/N 92-02-31413, 15-HP, 12" x 15" Opening

PROCESS COOLING WATER EQUIPMENT1 – TRANE MODEL CGAEC604AEA1FGTWRH 60-TON CHILLER, S/N J97G60252 (1997)1 – TRANE MODEL CGAEC804RANJJ42FGRWM 80-TON CHILLER, S/N J90B70602 (1990)1 – PROCESS COOLING WATER RECIRCULATION SYSTEM, Closed Loop Sytem, (2) 10-HP & (1) 1-1/2-HP Recirculation

Pumps, 2' x 5' x 10' High Water Holding Tank, Armstrong Model PEX8, 10" x 12" x 24" Plate Type Heat Exchanger, KinetcoWater Softening System

COMPRESSED AIR EQUIPMENT1 – INGERSOLL RAND MODEL SSR-EP50SE 50-HP ROTARY SCREW AIR COMPRESSOR, S/N G1095U92344, 198 SCFM,

125 PSIG, Air Cooled, Sound Enclosure Panels1 – GARDNER DENVER MODEL RNC 250A3 REFRIGERATED COMPRESSED AIR DRYER, S/N RG0J0250A0BA2NK06058,

250 SCFM @ 100 PSIG @ 100 Degree Fahrenheit

FORKLIFTS2 – HYSTER S50XL 4750-LB. CAPACITY FORKLIFTS, S/Ns C187V15888S, C187V15911S, LPG, Solid Tires, 189" Lift, 3-Stage Mast, Side Shift1 – HYSTER S35XM 3300-LB. CAPACITY FORKLIFT, S/N C010H03792U, LPG, Solid Tires, 189" Lift, 3-Stage Mast, Side Shift1 – RAYMOND MODEL EASI-R30TN 3000-LB. CAPACITY STAND-UP RIDER ELECTRIC FORKLIFT, S/N ET-D-00-10020

(2000), 134" Lift, Reach Type Forks, Side Shift, 24 Volt, With GNB FLX200 Industrial Battery Charger1 – CROWN MODEL 35RCTT 2950-LB. CAPACITY STAND-UP RIDER ELECTRIC FORKLIFT, S/N W-92992 (Not In Service)

MATERIAL HANDLING1 – NATIONAL BULK EQUIPMENT HYDRAULIC CARTON DUMPER, S/N NA,

Standard Gaylord Carton Size, Self-Contained Hydraulics28 – SECTIONS 80" WIDE X 48" DEEP X 12' HIGH ADJUSTABLE PALLET RACK-

ING, Tear-Drop Uprights, 2 Tier Cross-Beams60 – ROPAK 45" X 48" X 28" HIGH COLLAPSABLE SIDE POLY SKID BOXES25 – 45" X 48" POLY TRANSPORT DUNNAGE PALLETS (Sides Removed)25 – PORTABLE STACKABLE STEEL FLOW-BIN TOTES, Sizes to 45" x 45" x 48"

High

LAB EQUIPMENT1 – FARREL 12" X 6" X 6" 2-ROLL LAB MILL, S/N 52093, 7-1/2-HP, Oil Heated

Rolls, Hot Oil Heating Unit1 – BRABENDER TYPE IND/EXTR/16-04-000 INDEPENDENT LAB EXTRUDER,

S/N 1028/1, 3-Zone Digital Heat1 – DYNISCO POLYMER TEST LMI 4000 SERIES PROGRAMMABLE MELT

INDEX TESTER, S/N NA1 – ADMET PROGRAMMABLE TENSILE TESTER, S/N NA1 – MACBETH SPECTRA LIGHT II COLOR TEST BOOTH, S/N NA, 36" x 22"1 – CARVER MODEL C SAMPLE LABORATORY PRESS, S/N 2112-9, 6" x 6"

Platen, Hand Hydraulic JackMISCELLANEOUS LAB EQUIPMENT INCLUDING, Scales, Heaters, Hot Plates,Stirrers, Cabinets, Lab Benches, etc.

MISCELLANEOUS EQUIPMENT1 – 2 FLOOR HYDRAULIC PLATFORM SERVICE ELEVATOR, Services Littleford

& MTI Mixing Lines Upper Decks1 – MIMA MODEL LG208 PALLET SHRINK WRAP MACHINE, S/N LG208-05642 – INTERMEC MODEL 3400 LABEL PRINTERS2 – INTERMEC EASY CODER 3400e & PD41 LABEL PRINTERS

AUTOMOBILE1 – 2003 DODGE INTREPID SE 4-DOOR SEDAN, VIN: 2B3HD46R83H548415, Power

Windows, Power Locks, Power Steering, Air Conditioning, Cruise, 84,000 Miles

MISCELLANEOUS SHOP & FACTORY(1) Jesco 1-1/2 Cu. Yd. Self-Dumping Hopper, (1) Forklift "Man Basket" Attachment,(6) Rolling Step Ladders – (1) 10', (1) 9', (1) 7', (1) 5', (2) 3', (1) Spring-Type LiftManual Turntable, Miscellaneous Electronic Scales, Workbenches, Misc.Maintenance Supplies, Spare Parts, Pallet Jack, Hand Carts, Carton Stapler

OFFICE FURNITURE

1 – DAVIS STANDARD GEMINI MODEL GP-140-MM LINE #2 INCLUDING:• (1) 140mm (5.5") PARALLEL TWIN SCREW EXTRUDER, S/N AV030/78340 (2004), 12' Barrel Length,

200-HP Drive, Gear Ratio 31.5, Extruder RPM 30, Electric Band Heat, Motorized Additive Gate and MotorizedRotary Paddle, Console Control, With Digital Heat Controllers

• (1) BKG MODEL COMPACT 120 UNDERWATER PELLETIZER, S/N 2004-09-44 (2004), Wet BoxCutting Chamber, 13.4 KW Cutter Head, Master 2000 Dryer System, S/N 2003-11-25, Hot Water Tank,Drying Hopper, Exhaust, Recirculation System, Console Control with Siemens Simatic PLC

• (1) RICE LAKE 48" X 48" X 5000-LB. ELECTRONIC PLATFORM SCALE, With Programmable Readout1 – CINCINNATI MILACRON MODEL TP 140-26-1 LINE #7 INCLUDING:

• (1) 140mm TWIN SCREW EXTRUDER, S/N F1OA0100015 (2000), 26: 1 L/D Ratio, 200-HP, ElectricBand Heat, Liquid Cooled, 12' Barrel Length

• (1) CONAIR TRU FEED GRAVIMETRIC FEEDER, With Programmable Control & Motorized Gate• (1) BKG UWG COMPACT 120 UNDERWATER PELLETIZER, S/N 2004-04-13, Wet Cutting Chamber,

Motorized Cutterhead (Not in Service), Master 2000 Dryer System, S/N 2004-09-44, Hot Water Tank, Dryer,Recirculation Pumps, Filter, Console Control, With Siemens Simatic PLC

• (1) METTLER TOLEDO 48" X 48" X 5000-LB. ELECTRONIC PLATFORM SCALE, WithProgrammable Readout

1 – CINCINNATI MILACRON MODEL CM 92 HP LINE #3 INCLUDING:• (1) 92 mm (3.6") CONICAL TWIN SCREW EXTRUDER, S/N E15A020008, (2000), 27.2: 1 L/D Ratio,

150-HP, 98' Barrel, Electric Band Heat, Liquid Cooled, Console Control, With Digital Heat Controllers• (1) CONAIR TRU FEED GRAVIMETRIC FEEDER MOTORIZED REGULATOR FEED HOPPER• (1) GALA UNDERWATER PELLETIZER, S/N 992165, With Wet Box Cutting Chamber, 15-HP Cutter

Head, Model 140 GP Stainless Steel Hot Water Tank, Model 2016 DW Dryer, Model 160-FRU FinesRemoval Sieve, Recirculation Pumps

1 – CINCINNATI MILACRON MODEL CM 92 HP LINE #6 INCLUDING:• (1) 92mm (3.6") CONICAL TWIN SCREW EXTRUDER, S/N E15A0298011 (1998), 27.2: 1 L/D Ratio,

150-HP, 98" Barrel, Electric Band Heat, Liquid Cooled, Console Control, With Digital Heat Controllers• (1) ACCU RATE REGULATED FEEDER• (1) GALA UNDERWATER PELLETIZER, S/N 982436, Wet Box Cutting Chamber, 15-HP Cutterhead, 140

CPM Electric Hot Water Polymer Heating Tank, 40" Diameter x 48" High, Stainless Steel, Model 2016 DWDryer, FRU-160 Fines Removal Sieve, Recirculation Pumps

• (1) 48" x 48" x 5000-LB. ELECTRONIC PLATFORM SCALE, With Mettler Toledo Prog. Readout1 – CINCINNATI MILACRON MODEL CM-92-HP LINE #5 INCLUDING:

• (1) 92mm (3.6") CONICAL TWIN SCREW EXTRUDER, S/N 4215A01/95-1 (1995), 27.2: 1 L/D Ratio,150-HP, 98" Barrel, Electric Band Heat, Liquid Cooled, Console Control, With Digital Heat Controllers

• (1) GALA UNDERWATER PELLETIZER, S/N 952239, Wet Box Cutting Chamber, Motorized CutterHead, 80/TWS Hot Water Polymer Heating Tank, 31" x 31" Stainless Steel Tank, Model B-2BF Dryer,FRS-160 Fines Removal Sieve, Recirculation Pumps

1 – CINCINNATI MILACRON MODEL CM-92-HP LINE #4 INCLUDING:• (1) 92mm (3.6") CONICAL TWIN SCREW EXTRUDER, S/N 4215A01/94-1 (1994), 27-2: 1 L/D Ratio,

150-HP, 98" Barrel, Electric Band Heat, Liquid Cooled, Console Control, With Digital Heat Controllers• (1) CONAIR GRAVIMETRIC TECHNOLOGY TRU FEED GRAVIMETRIC FEEDER, With Prog. Control• (1) BKG UNDERWATER PELLETIZER (2004), Wet Box Cutting Chamber, UWG Compact 120 6.0 KW Cutter

Head, S/N 2003-11-25, Model Master 1000 Dryer, S/N 2004-04-13, Stainless Steel, Electric Heat, Hot WaterTank, Recirculation Pump, With Filter, Exhaust Blower

• (1) 48" x 48" x 5000-LB. ELECTRONIC PLATFORM SCALE, With Rice Lake 120 Prog. Readout

5

MIXING & BLENDING EQUIPMENT • PROCESS COOLING • EXTRUDERS

(1 OF 3) JACKETED RIBBON BLENDERS

MTI MIXING LINE INCLUDING: (1) PREMIER MATERIAL DELIVERY PUMP

PROCESS COOLING WATER SYSTEM

DAVIS STANDARD MV251N25 2-1/2" EXTRUDER

ARBURG MODEL 221-55-250 28-TON PLASTIC INJECTION MOLDING MACHINE

FILTREX C41000 CENTRALDUST COLLECTOR

MIXING AND BLENDING EQUIPMENT

Line may be sold bulk subject to the piecemeal bids1 – MTI MIXING LINE INCLUDING: (1) PREMIER MATERIAL

DELIVERY PUMP, With Sutorbilt Model GAEMPDA 15-HPVacuum Pump/Blower, S/N S041193

• (1) PREMIER MATERIAL DELIVERY PUMP, With Sutorbilt ModelGAEMDPA 7.5-HP Vacuum Pump/Blower, S/N S031853

• (2) PREMIER PNEUMATICS MATERIAL RECEIVING HOPPERS, Bin Level Indicators

• (2) BRABENDER MODEL FW120/600 FEEDERS, S/Ns BT19901012, BT19901011 (1999), Stainless Steel, BinMaster Model GR Electric Rotary Level Indicator

• (1) WALTON STOUT RECEIVING HOPPER, Pneumatic Pulse Jet,Cone Bottom, With Rotary Airlock Discharge

• (2) ELECTRONIC LOAD CELL WEIGH SCALE HOPPERS• (2) SENSOR TRONICS MODEL 2010 PROGRAMMABLE

WEIGHT CONTROLLERS• (1) MTI MODEL W1000S MIXER, S/N 1314 (1998), 350-HP, 42"

Diameter Stainless Steel Vertical Chamber, Vertical Shaft,Pneumatic Discharge Gate

• (1) STEEL SUPPORT SUPERSTRUCTURE1 – RELIANT 400-HP VERTICAL SHAFT MIXER, S/N N/A,

48" Diameter Stainless Steel Chamber, Material Weigh Scale Bin,Oil Weigh Scale Hopper, Pneumatic Discharge Gate

1 – VERTICAL SHAFT MIXER, MFG'R & MODEL NA, Approximately300-HP, 48" Diameter Stainless Steel Chamber, Material WeighScale Bin, Oil Weigh Scale Hopper, Pneumatic Discharge Gate

3 – JACKETED RIBBON BLENDERS, S/Ns 00100040613R,03100040690NR, 03100040696NR, Stainless Steel, 4' Diameter x7', 40-HP Gear Reduced Drive, Bottom Discharge, With PneumaticDischarge Gate, Stand Mounted, Operators Platform

1 – JACKETED RIBBON BLENDER, S/N N/A, Stainless Steel, 36"Diameter x 10-1/2', Approximately 40-HP Geared Drive, PneumaticDischarge Gate, Operators Platform

1 – YOUNG JACKETED RIBBON BLENDER, S/N 5337-1148-2819,Stainless Steel, 32" Diameter x 40", HP N/A, Design Pressure 15PSI – 650 Degree Fahrenheit, Jacket and Shell Thickness 3/16",Pneumatic Discharge Valve

PLASTIC EXTRUDER1 – DAVIS STANDARD MODEL MV251N25 2-1/2" EXTRUDER,

S/N AG590/74694 (2002), 40-HP, 60" Barrel Length, Gear Ratio17.26, Extruder RPM 100, Liquid Cooled, Electric Band Heat, DigitalTemperature Controls, Model 1 Zone Ext. Type DSPA Die Head

INJECTION MOLDING MACHINE1 – ARBURG MODEL 221-55-250 28-TON PLASTIC INJECTION

MOLDING MACHINE, S/N 148963, 2 oz. Polystyrene Shot Size,22mm Screw Diameter, Mold Height Range 7 in. – 5.91 in.,Maximum Daylight between Platens 6 in., Platen Size 7" x 7"

GRANULATORS3 – WORTEX MODEL JC-10 GRANULATORS, S/Ns 2910, 3233,

2617, Opening Size 10" x 12"

TEMPERATURE CONTROL UNITS1 – STERLCO MODEL 6016-MX TEMPERATURE CONTROL UNIT,

S/N 637901 – AEC TCO-1 TEMPERATURE CONTROL UNIT, S/N 37H0363

SEPARATORS/SIZERS3 – MIDWESTERN INDUSTRIES MODEL MR6088-8-C GYRA-VIB

60" VIBRATORY SEPARATOR/SIZERS, S/Ns 0705-5023, 0905-5028, 0905-5029 3 Screen Decks, 2-1/2-HP

2 – THERMAL ENGINEERING MODEL TEA-48 SHAKER SCREEN48" VIBRATORY SEPARATOR/SIZERS, S/Ns 93-1447, N/A, 2-1/2-HP, 2 Screen Decks

1 – THERMAL ENGINEERING 48" DIAMETER VIBRATORYSEPARATOR/SIZER, S/N N/A, 2 Screen Decks

DUST COLLECTORS1 – FILTREX MODEL C41000 CENTRAL DUST COLLECTOR,

S/N F10218, Pneumatic Pulse Jet Self-Cleaning, Stand Mounted1 – FREE-STANDING CENTRAL DUST COLLECTOR, MFG'R N/A,

Pneumatic Pulse Jet Self-Cleaning, Bottom Discharge, WithMotorized Rotary Airlock Valve

BULK MATERIAL STORAGE ANDTRANSPORT EQUIPMENT

8 – BULK MATERIAL STORAGE SILOS, Welded Carbon Steel, 11-1/2' x11-1/2' x Approximately 35' High, Square Design, Cone Bottom, SteelLeg Mounted

2 – 12' X APPROXIMATELY 40' BULK MATERIAL STORAGE SILOS2 – 12' X APPROXIMATELY 30' BULK MATERIAL STORAGE SILOS1 – CHICAGO CONVEYOR CORP. BULK MATERIAL VACUUM

UNLOADING/CONVEYING SYSTEM, S.O. NO.10985, 50-HPPressure Blower, With Air Cooled Heat Exchanger, 40-HP VacuumBlower, With Filter, Stainless Steel Receiver Filter, 4' x Approximately15' High, Rotary Airlock Discharge, Pneumatic Pulse Jet, Bin LevelIndicators

1 – DOVER MODEL VPS-5 VACUUM BULK MATERIAL UNLOADERSYSTEM, S/N D-1314, Roots Model 412-Roots-Flo 50-HP RotaryLobe Blower, S/N 0602922411, Skid Base, Pneumatic Filter Tank

1 – CYCLONAIRE PORTABLE VACUUM UNLOADER SYSTEM FILTER UNIT, S/N N/A

1 – BULK MATERIAL UNLOADER, 100-HP Pump/Blower, MFG'R N/A1 – WALTON STOUT VACUUM SYSTEM, With Gardner Denver Dura

Flow Model GGDCADA, 30-HP Pump/Blower1 – VACUUM PUMP SYSTEM, ROOTS/DRESSER 40-HP ROTARY

LOBE BLOWER, S/N 931-27501 – SPENCER 5-HP VACUUM PUMP BLOWER, S/N N/A1 – DRESSER 93-2703 50-HP VACUUM PUMP/BLOWER, S/N N/A

BULK BAG EQUIPMENT2 – CONTROL & METERING MODEL FEF-S DISCHARGE BULK BAG

METERING DISCHARGE STANDS, S/Ns C3782, C3791 (1999),Receiving Hopper, With Pneumatic Discharge Gate, Stand Mounted

1 – CONTROL & METERING MODEL FL-F DISCHARGER BULK BAGDUMP STAND, S/N C1559, 45" x 45" Hopper, With Vibco ElectricVibrator

1 – HAPMAN 42" X 28" DOWNDRAFT BAG BOOTH, S/N AB-3240,Closure Lid, Exhaust Blower

PROCESS COOLING WATER EQUIPMENT1 – TRANE MODEL CGWD0504CJQHAT101FFOUG 50-TON CHILLER,

S/N U96E04424 (1996), 15/10/10/10 Nominal HP/Ton Rating, (2) 1800Gallon Poly Holding Tanks, Whitlock Control Panel, RecirculationPumps

1 – PROCESS COOLING WATER SYSTEM, With (2) Approximate 3000-Gallon Poly Holding Tanks, Each With (2) 10-HP Recirculation Pumps,Heat Exchanger, Filter Tech Model LGF4-480 Filter, S/N 041272121, 50" Wide Paper Media

1 – EMERALD MODEL 556 PROCESS COOLING WATER UNIT, S/N 039, 72" x 72" x 60" Open Top Holding Tank, (2) 10-HPRecirculation Pumps

COMPRESSED AIR EQUIPMENT1 – SULLAIR V-120-50 H/A 50-HP ROTARY SCREW AIR

COMPRESSOR, S/N 003-139764, Air Cooled, SoundEnclosure Panels

2 – SULLAIR MODEL LS-10 40-HP ROTARY SCREW AIR COMPRESSORS, S/Ns N/A, Air Cooled, Skid Base,Aftercooler

1 – SULLAIR SR-250 REFRIGERATED COMPRESSED AIR DRYER, S/N 2899050004

1 – CURTIS DRI-PLUS SYSTEMS CDP-8200 REFRIGERATEDCOMPRESSED AIR DRYER, S/N 0325-A-102A-9811-9N, 200SCFM Capacity

1 – 36" DIAMETER X 8' HIGH VERTICAL COMPRESSED AIRRECEIVER TANK

LAB EQUIPMENT1 – LITTLEFORD MODEL N/A LAB MIXER, S/N N/A, 9" x 9"

Stainless Steel Mixing Chamber, AC Drive Motor, With LoadPercent Meter

1 – FARREL 12" X 6" X 6" 2-ROLL LAB MILL, S/N 57A1263,Liquid Temperature Regulated Rolls

1 – MFG'R NA, 12" x 6" x 6" 2-ROLL LAB MILL, S/N N/A1 – WABASH 50-1512-2T2WSM 50-TON HYDRAULIC LAB

COMPRESSION PRESS, S/N 8824, Compression Cylinder7 x 12, Platen Size 15"LR x 12"FB, Electric Platen Heat,Upacting, Self-Contained Hydraulics

1 – C.W. BRABENDER PLASTI-CORDER TYPE DR-2051LAB EXTRUDER, S/N 0328XXPE, 5-HP AC Drive, PL2100Digital Temperature Control Panel, With Power Supply

1 – LLOYD INSTRUMENTS MODEL LRX5K COMPUTERIZEDTENSILE STRENGTH TESTER, TYPE TG18, S/N W090979802, 5KN Maximum Load, 36" Vertical Travel,Programmable Readout, PC Control

1 – TMI MODEL 43-02-01-0001 PROGRAMMABLE IMPACTTESTER, S/N 27819-01, Programmable Monitor

1 – QUV MODEL QUV/SPRAY ACCELERATED WEATHERING TESTER, S/N N/A, Programmable, SolarEye UV Irradiance Controller

1 – GRETAG MACBETH MODEL COLOR EYE 7000ACOLOR ANALYZER, S/N 37102450447, PC Control

1 – FISCHER SCIENTIFIC MODEL 655F ELECTRIC LABOVEN, S/N 20900260, 24" x 18" x 20"

1 – AMINCO LAB MATERIAL HEATER, S/N N/A1 – GARDNER IMPACT TESTER, S/N N/ALab Equipment Including, Lab Hood, Benches, Cabinets, Scales,Lab Mixers, Hot Plates, Sieve Shaker, Microscope, Lab Ware

6

FORKLIFTS • MISC. EQUIPMENT • EXTRUDER PELLETIZING LINES

VIEW OF CATEPILLAR, CLARK, CROWN & DAEWOO ELECTRIC FORKLIFTS

Additional Extruder Pelletizing Lines are located on pages 2, 3 & 4 of this brochure.

EXTRUDER PELLETIZING LINESLines may be sold bulk subject to the piecemeal bids

TO 5,000-LB.

WERNER & PFLEIDERER ZSK-92 (3.6") TWIN SCREW EXTRUDER DAVIS STANDARD THERMATIC 60IN60TPIH 6" EXTRUDER CONAIR JETRO MODEL 212, 12" 15-HPDRY TYPE PELLETIZER

FORKLIFTS1 – CATERPILLAR MODEL GP25K 4400-LB. CAPACITY FORKLIFT, S/N AT17B-11974, LPG, Solid Tires, 188" Lift, Side Shift3 – CATERPILLAR MODEL 2EC25E 5000-LB. CAPACITY SIT-DOWN RIDER ELECTRIC FORKLIFTS,

S/Ns A2EC263252, A2EC363091, A2EC363099, 188" Lift, Side Shift, 36" Forks, 36 Volt3 – CLARK MODEL ECG25 4800-LB. CAPACITY SIT-DOWN RIDER ELECTRIC FORKLIFTS, S/Ns ECG358-0204-

6809FB, ECG358-0095-6751FB, ECG358-0084-6789FB1 – CROWN 4000-LB. CAPACITY SIT-DOWN RIDER ELECTRIC FORKLIFT, S/N 1A146844, 188" Lift1 – DAEWOO MODEL 8C20S 4000-LB. CAPACITY SIT-DOWN RIDER ELECTRIC FORKLIFT, S/N 27-0036, (No Battery)1 – CROWN 3700-LB. CAPACITY SIT-DOWN RIDER ELECTRIC FORKLIFT, S/N 1A145432, 188" Lift, Side Shift,

36" Forks, 36 Volt2 – YUASA MODEL TGN-18-1050 36 VOLT INDUSTRIAL FORKLIFT BATTERY CHARGERS, S/Ns WD 88788,

WI 968201 – MAC QUANTUM SERIES MODEL 18Q105002A 36 VOLT INDUSTRIAL FORKLIFT BATTERY CHARGER,

S/N 992256791 – MAC QUANTUM SERIES MODEL 18Q970C2A 36 VOLT INDUSTRIAL FORKLIFT BATTERY CHARGER,

S/N 990134811 – MAC QUANTUM SERIES MODEL 180970C2A 36 VOLT INDUSTRIAL FORKLIFT BATTERY CHARGER,

S/N 990134821 – POEHLERPROZESS INDUSTRIAL FORKLIFT BATTERY CHARGER, S/N N/A1 – LIFEGUARD MODEL LG18-1050F3B 36 VOLT INDUSTRIAL FORKLIFT BATTERY CHARGER, S/N 97U3958

MATERIAL HANDLING120 – JOHNSON 44" X 44" X 36" STACKABLE STEEL MATERIAL FLOW BIN TOTE BINS1 – MATERIAL TRANSFER AND STORAGE HYDRAULIC CARTON TIPPER, S/N N/A,

Standard Gaylord Carton Size1 – IMS MODEL 111871 TUMBLER DOUBLE-END 55-GALLON DRUM TUMBLER, S/N 09041 – 48" X 48" X 5000-LB. ELECTRONIC PLATFORM SCALE, With Mettler Toledo Panther

Plus Programmable Readout1 – 48" X 48" X 5000-LB. ELECTRONIC PLATFORM SCALE, With Programmable Readout1 – METTLER TOLEDO MODEL VLX 48" X 48" X 5000-LB. ELECTRONIC PLATFORM

SCALE, S/N 1142609-1EH, With Programmable Readout1 – METTLER TOLEDO 18" X 18" BENCH TOP ELECTRONIC SCALE, With Programmable

Counting Scale1 – AND BENCH TOP ELECTRONIC SCALE

AUTOMOBILES1 – 2006 FORD TAURUS SEL 4-DOOR SEAN VIN: 1FAFP56U56A251053, With Power

Windows, Power Locks, Air Conditioning, Programmable Entry Locks, Sunroof1 – 2005 DODGE NEON SXT 4-DOOR SEDAN, VIN: 1B3ES56C65D110518, With Power

Windows, Power Locks, Air Conditioning, (52,000 Miles)

MISCELLANEOUS EQUIPMENT1 – RIDGID MODEL 700 HAND HELD POWER PIPE THREADER, S/N EE16294-06032 – DEWALT MODEL DW 304P ELECTRIC RECIPROCATING SAWS1 – DEWALT MODEL DW 290 1/2" DRIVE ELECTRIC IMPACT WRENCH1 – BOSCH BULLDOG 11224 VSR ELECTRIC HAMMER DRILL1 – DEWALT DW 239 1/2" ELECTRIC DRILL MOTOR1 – HYDRAULIC PORT-A-POWER KIT1 – HITACHI MODEL C10 FS 10" SLIDING COMPOUND MITRE SAW1 – CLAUSING 15" DRILL PRESS1 – CRAFTSMAN 6" DOUBLE-END GRINDER1 – FAMCO No. 3-1/2 R ARBOR PRESS1 – MAKITA 2414NB 14" ABRASIVE CUT-OFF SAW1 – REPUBLIC 14" x 40" ENGINE LATHE1 – MILLPORT 2-HP 16-SPEED VERTICAL MILLING MACHINE1 – 6" x 12" HAND FEED SURFACE GRINDERGang Box, Welding Table, Welding Screens, Step Ladders, Maintenance and Repair Parts,Spare Equipment Parts, Motors, Pumps, Blowers, Hoppers, etc.

OFFICE FURNITURE & EQUIPMENT

1 – WERNER & PFLEIDERER EXTRUDER PELLETIZING LINE, INCLUDING:• (1) MAC 464A/6MVLBHC 15-HP MATERIAL TRANSFER VACUUM/BLOWER, S/N 9-PD6V-02-003• (1) MAC VACUUM RECEIVER/FILTER HOPPER, Vacuum Fed, Gravity Discharge, With Air Knife Gate,

Bindicator Level Indicators, Vibrators, Filter Bags, Top Air Manifold• (1) SCHENCK ACCU RATE ELECTONIC WEIGH SCALE PROGRAMMABLE FEEDER HOPPER• (1) SCHENCK ACCU RATE PROGRAMMABLE COLOR ADDITIVE AUGER FEEDER• (1) SCHENCK ACCU RATE PROGRAMMABLE REGRIND ADDITIVE AUGER FEEDER, With

Foremost Vacuum Loader• (1) SCHENCK ACCU RATE MAIN CONTROL PANEL, With Dry Blend, Color, & Blend Prog. Controllers• (1) WERNER & PFLEIDERER MODEL ZSK-92 (3.6") TWIN SCREW EXTRUDER, S/N 180770 (1994),

60" Barrel Length, 400-HP DC Drive, Electric Bank Heat, Liquid Cooled, Control Panel• (1) VACUUM ASSIT TRANSFER BOX DISCHARGE, With Vacuum Power Unit• (1) W&P MODEL ESA-200, 200mm (7.8") SINGLE SCREW CROSS EXTRUDER, S/N 108770 (1994),

48" Barrel Length, HP NA, Liquid Cooled, Electric Band HeatA/or Hot Oil Heated Hollow Screw• (1) EXTRUSION SPECIALTY PRODUCTS MODEL SA-2/20 HOT OIL HEATER, S/N 01043, 20 Kw• (1) HOT FACE CUTTER PELLETIZER, 30" Diameter 2 Blade Cutter Head, Gravity Drop Discharge• (1) MATERIAL TRANSFER POSITIVE DISPLACEMENT BLOWER, HP NA, 6" M-Floor Piping• (1) MATERIAL TRANSFER ASSIST POSITIVE DISPLACEMENT BLOWER FOR VERTICAL TRANSFER• (1) WERNER & PFLEIDERER MODEL GFC 230X45, 90.5" X 17.7" AIR BED DRYER, S/N 507823

(1993), Forced Air Blower (HP NA)• (1) SWECO VIBRO ENERGY 48" VIBRATORY SEPARATOR/SIZER, S/N NA, (2) Sizing Screen Decks,

Solid Inner/Outer Ring Top Screen• (1) MATERIAL TRANSFER POSITIVE DISPLACEMENT BLOWER, HP NA• (1) MATERIAL LOAD-OUT STAND, With Receiving Cyclone, Gravity Drop, Holding Hopper, Super Sack

Filler Framework or Gaylord Box Load• (1) TOLEDO 60" X 60" X 5000-LB. ELECTRONIC PLATFORM WEIGH SCALE, With Programmable Readout

1 – DAVIS STANDARD EXTRUDER PELLETIZING LINE INCLUDING:• (1) 15-HP VACUUM PUMP/BLOWER PNEUMATIC CONVEYING POWER UNIT• (1) MAC VACUUM RECEIVER/FILTER HOPPER, Vacuum Fed, Cone Bottom Discharge, With Air Knife

Gate, Filter Bags, Top Air Manifold• (1) ACCU RATE DRY MATERIAL FEEDER, Electronic Weigh Hopper Receiver/Feeder• (2) ACCU RATE ADDITIVE AUGER FEEDERS, (1) Color, (1) Regrind• (1) ACCU RATE MASTER CONTROL PANEL, With Schenck Disocont Programmable Controls• (1) DAVIS STANDARD THERMATIC MODEL 60IN60TPIH 6" EXTRUDER, S/N L-9918 (1991),

30:1 L/D Ratio, 15' Barrel Length, 300-HP, Electric Band Heat, Liquid Cooled, Console Control, WithEurotherm Digital Heat Controls

• (1) EXTRUSION DIES INC. 21" WIDE STRAND TYPE DIE HEAD, Electric Heat, Off-Line Retractable• (1) STAINLESS STEEL WATER BATH TABLE, 10' Length x 24" Wide x 12" Deep, Caster Mounted,

Connected Into Central Process Water Chill/Recirculation System• (1) BERINGER MODEL WS75 AIR WIPE DRYER, S/N 12D315• (1) CONAIR JETRO MODEL 212, 12" 15-HP DRY TYPE PELLETIZER, S/N 8-120281• (1) 15-HP VACUUM PUMP/BLOWER PNEUMATIC CONVEYING POWER UNIT• (1) WERNER & PFLEIDERER MODEL GFC 110X75, 43" X 29.5" AIR BED DRYER, S/N 230805,

Vacuum Receiver Hopper, 20-HP Air Blower• (1) SWECO VIBRO-ENERGY MODEL LS48C66, 48" VIBRATORY SEPARATOR/SIZER,

S/N C117817C, 2-1/2-HP (2) Sizing Screen Decks, Solid Inner/Outer Ring Top Screen• (1) 10-HP POSITIVE DISPLACEMENT TRANSFER BLOWER• (1) MATERIAL LOAD-OUT STATION RECEIVING CYCLONE/HOPPER, Super Structure Stand Mounted• (1) ST. REGIS MODEL 106-FGS BAGGER, S/N 752313, Mechanical Pre-Set Weigh Type, Off-Line

Track Mounted Retractable• (1) METTLER TOLEDO 60" X 60" X 5000-LB. ELECTRONIC PLATFORM WEIGH-OUT SCALE,

With Programmable Readout

7

MIXING/BLENDING • BULK STORAGE • MATERIAL HANDLING

BULK STORAGE/DISTRIBUTION2 – 12' X 40' BULK DRY MATERIAL STORAGE SILOS, Bolted

Steel Panels1 – 10' X 30' BULK DRY MATERIAL STORAGE SILO, Welded Carbon Steel1 – MAC 40-HP MATERIAL TRANSFER VACUUM/BLOWER

SYSTEM, S/N NA6 – PLASTICIZER OIL BULK STORAGE TANKS, Approximately 10' x

20', Welded Carbon Steel, Steel Leg Stand, Tapered Bottom, EachWith Viking HL-4125 2-HP Pump

2 – PLASTICIZER OIL BULK STORAGE TANKS, Approximately 10' x15', Welded Carbon Steel, Steel Leg Stand, Tapered Bottom, EachWith Viking HL-4125 2-HP Pump

1 – MAC 4-STATION SUPER SACK BULK BAG RECEIVING STATION, (4) Receiving Hoppers, With Electronic Vibrators,Vacuum Unload (Connected to Common Usage Vacuum System)

1 – MAC MODEL 36AV8 HAND BAG DUMP BENCH, S/N 91-AVSF-06-011, Self-Contained Dust Collector, VacuumUnload (Connected to Common Usage Vacuum System)

MIXING/BLENDING MASTER CONTROL SYSTEM

1 – MAC COMPUTERIZED CONTROL ROOM SYSTEM WONDERWARE TRADEMARKED/LICENSED OPERATING SOFTWARE(Customer Licensing/Subscription Required), Control Panels,Operating Terminals, Display Monitors

DUST COLLECTION SYSTEM1 – 50-HP CENTRAL FINES DUST COLLECTION SYSTEM,

Pneumatic Pulse Jet, Receiver Cyclone

GRANULATORS2 – WORTEX MODEL JC-10L GRANULATORS, S/Ns 1335, 1384,

Opening Size 18" x 10"

PROCESS COOLING WATER EQUIPMENT

1 – APPLICATION ENGINEERING (AEC) GLACIER SERIES MODELNXGA-30 PROCESS WATER CHILLER, S/N 98L0402, 30-HPCompressor

2 – APPLICATION ENGINEERING (AEC) S-190ME-Q PROCESSWATER CHILLERS, S/Ns 89K373, 89K372, 25/10-HP

1 – PROCESS COOLING WATER RECIRCULATION UNIT, WithHolding Tank & Pumps

COMPRESSED AIR EQUIPMENT1 – INGERSOLL RAND MODEL SSR 50-HP ROTARY SCREW AIR

COMPRESSOR, S/N NA, Air Cooled, Sound Enclosure Panels1 – ULTRA AIR UA-250-AC REFRIGERATED COMPRESSED

AIR DRYER, S/N A00010

MATERIAL HANDLING250 – 45" x 48" x 32" HIGH COLLAPSIBLE SIDE POLY SKID BOXES1 – VESTIL MFG MODEL HBD-2-48 HYDRAULIC CARTON TIPPER,

S/N NA, 2000-Lb. Capacity, Standard Gaylord Carton Size1 – ABELL HOWE 1/2-TON CAPACITY COLUMN MOUNTED JIB

CRANE, S/N 91-28022, With Yale 1/2-Ton Electric Chain Hoist, (MTI Receiver Bin Deck)

20 – 40" X 40" X 30" STACKABLE FLOW BIN TOTE BINSMiscellaneous Pallet Racks, Hand Carts, Pallet Jacks

FORKLIFTS1 – TCM MODEL FCG25N6T 5000-LB. CAPACITY FORKLIFT,

S/N A48805902, LPG, Solid Tires, 130" Lift1 – TCM MODEL FCG25N6 4600-LB. CAPCITY FORKLIFT,

S/N A48804150, LPG, Solid Tires, 189" Lift, 42" Forks1 – TCM MODEL FCG25T7T 4600-LB. CAPACITY FORKLIFT,

S/N A15G03063, LPG, Solid Tires, 189" Lift, 42" Forks

LAB EQUIPMENT1 – CARVER MODEL 4533-4D11B0C LAB PRESS, S/N 4533-011

(2007), 15" x 17" Electric Heated Platens, Auto SeriesProgrammable Control

1 – KSBI 12" X 6" X 6" 2-ROLL LAB MILL, S/N 14864, TemperatureControlled Rolls, 5.5 KW

1 – BRABENDER PLASTI-CORDER MODEL DR-2051 LAB EXTRUDER, S/N 0287-PE, 5-HP, PL2000 Programmable Controls

1 – BENZ LAB STIRRER2 – CARVER HYDRAULIC LAMINATING PRESSES1 – SCOTT TESTER IMPACT TESTERElectronic Scales, Hot Plates, Labware, Benches, Cabinets

STRAIGHT TRUCK1 – 1995 INTERNATIONAL 4700 24' SINGLE AXLE VAN BODY

STRAIGHT TRUCK, VIN: 1HTSCAAM9TH306274, DT466 Diesel,Fuller 6 Speed, 254" Wheel Base, 24' Morgan Aluminum Van Body

AUTOMOBILE1 – 2005 FORD TAURUS SLE 4-DOOR SEDAN, VIN: 1FAFP56UX5A152338,

Power Windows, Power Locks, Air Conditioning, Programmable Entry Locks

MISCELLANEOUS EQUIPMENT1 – OTC POWER TEAM 50-TON HYDRAULIC PULLER SET,

With Portable Gang Box1 – MIMA MODEL LG-20 PALLET SHRINK WRAP MACHINE,

S/N 13369Maintenance & Repair Parts, Motors, Blowers, Pumps, Hoppers,Electrical & Pneumatic Scales, Fans, Carts, General Shop & Factory

OFFICEMiscellaneous Office Furniture & Equipment

VIEW OF MTI MIXER LINE MTI MIXER LINE MACRECEIVER/FILTER HOPPERS

BULK STORAGE SILOS & MAC 40-HPBLOWER SYSTEM

50-HP CENTRAL FINES DUST COLLECTION SYSTEM

LITTLEFORD 125-HP VERTICAL SHAFT MIXER INGERSOLL RAND MODEL SSR 50-HPROTARY SCREW AIR COMPRESSOR

APPLICATION ENGINEERINGPROCESS WATER CHILLERS

VIEW OF TCM FORKLIFTS TO 5,000-LB. CAPACITY

MIXING/BLENDING EQUIPMENTLine may be sold bulk subject to

the piecemeal bids1 – MTI MIXER LINE, INCLUDING:

• (1) MAC 463-A-4506, 20-HP MATERIAL TRANSFER VACUUM PUMP/BLOWER, S/N 91-PDBV-06-004

• (1) MAC 463-A-4506, 20-HP MATERIAL TRANSFER VACUUM PUMP/BLOWER, S/N 91-PDBV-06-006

• (3) MAC RECEIVER/FILTER HOPPERS, Filter Bags, AirManifold Pulse Jet, Stand Mounted, Electronic Bin LevelIndicators, With Auger Discharge

• (1) MAC RECEIVER/FILTER HOPPER, Filter Bags, AirManifold Pulse Jet, Stand Mounted, Electronic Bin LevelIndicator, With Rotary Airlock Discharge

• (1) PLASTICIZER OIL RECEIVING LOAD CELL WEIGHHOPPER

• (3) LOAD CELL WEIGH HOPPERS, With Air Knife GateDischarge, Vibrators, Electronic Level Indicators

• (1) MTI MODEL M750/K2400 VERTICAL SHAFT MIXER, S/N878 (1991), 300-HP, Stainless Steel

• (1) MTI 4' X 8' HORIZONTAL SHAFT PADDLE BLADECOOLING CHAMBER, S/N 878, Jacketed, Water Cooled, AirLock Chamber Door, Bottom Discharge, With Air Gate

• (1) PIT MOUNTED RECEIVING HOPPER, Gravity Fed,Electronic Bin Level Indicators, Vacuum Discharge

• (1) MAC MODEL 463-A-4506, 20-HP MATERIAL TRANSFERVACUUM PUMP, S/N 91-PDBV-06-005

• (1) CAMCORP 26SFPRT19-3 RECEIVER/FILER HOPPER, S/N 2463-2, Vacuum Fed, Gravity Discharge, WithRotary Airlock Valve, Filter Bags, Air Manifold Pulse Jet, 48"Diameter x 60", Electronic Bin Level Indicators, Vibrators

• (1) LK MODULAR STAINLESS STEEL RECEIVER HOPPER• (1) 60" X 60" X 5000-LB. ELECTRONIC PLATFORM WEIGH-

OUT SCALE, With Programmable Readout• (1) CENTRAL PC CONTROL CART end Line

1 – LITTLEFORD 125-HP VERTICAL SHAFT MIXER, MODEL &S/N NA (Stored)

1 – LITTLEFORD 40" X 11' HORIZONTAL SHAFT COOLINGCHAMBER, S/N 10521, 30-HP (Stored)

1 – HAND BATCH BLENDING STATION, With:• (8) Schenck Accu Rate 21" x 21" Stainless Steel Auger Feeder

Hoppers, Programmable Feed Rate Controls, Electronic Weigh Scale• (1) Allen Bradley Versa View 1200M Central PLC Control

Console, With (2) Mettler Toledo Jagxtreme ProgrammableScale Controls