EXPLORER SPORT / EXPLORER SPORT TRACWITH 4WD AUTOMATIC TRANSMISSION 2003 - 2005

US

E

F

INSTALLATION INSTRUCTION -

INSTRUCCIONESS DE INSTALACION -

INSTRUCTIONS D'INSTALLATION - Subject to alteration without noticeReservadas modificaciones tecnicas

Sous reserve de modificaciones techniques

PERSONAL INJURYLESIONES PERSONALESRISQUE DE BLESSURE

VEHICLE DAMAGEDANO DE VEHICULODOMMAGE AU VEHICULE

INCORRECTINCORRECTOINCORRECT

CORRECTCORRECTOCORRECT

SEE MANUALVER MANUALVOIR LE MANUEL

NEUTRAL TOW INDICATOR

© Copyright Ford 2005PG 1/9

INDICADOR NEUTRAL DEL REMOLQUE

INDICATEUR NEUTRE DE REMORQUAGE

A

cut along dotted line

Drill (2)3/16" Holes

allign with recess

B

8mm

7mm

1/4"

3/16"

TOOLS REQUIREDHERRAMIENTAS NECESARIASOUTILS NÉCESSAIRES

E The neutral tow feature(NTF) provides the convienience of towing your 4X4vehicle on the rear wheels or on all four wheels for extended distance with-out risking damage to the automatic transmission.

This vehicle has neutral tow capability. To engage the transfer caseinto neutral, follow the procedure listed below. If the transfer case isengaged in neutral, moving the shift lever out of neutral or moving the ignition switch to the ON or Start positions will result in the transfer case shifting out of neutral. Always verify that a low or dead battery condition does not existwhen shifting the transfer case into or out of neutral. Always applythe parking brake and remove the key when the vehicle is in PARK.Failure to follow these instructions could result in unexpected vehiclemovement or transmission damage. When the transfer case is in the neutral position, the engine and transmission are disconnected from the rest of the driveline. Therefore,the vehicle is free to roll. Make sure the vehicle is properly prepared for towing before shifting the transfer case into neutral (see supplement).

TO SHIFT THE TRANSFER CASE INTO NEUTRAL FOR TOWING: 1. Prepare the vehicle for towing. 2. Start the engine to make sure the battery is sufficiently charged. 3. Make sure vehicle is at a complete stop and the vehicle is shifted into two wheel drive 4.Place the automatic transmission shifter into NEUTRAL. 5.Turn the ignition switch to the OFF position (i.e. steering not locked). 6.Depress the brake pedal for 5 seconds. 7. The neutral light will initially go through a bulb check; then stay on to indicate the transfer case is in neutral. 8. Leave ignition switch in the OFF position and the transmission shifter in NEUTRAL while the vehicle is in tow.

DO NOT DISCONNECT TOWED VEHICLE BEFORE PLACING TRANSFER CASE INTO GEAR.

TO SHIFT THE TRANSFER CASE OUT OF NEUTRAL AFTER TOWING

1.Make sure vehicle is at a complete stop. 2. Turn the ignition to the ON (not START) position or move the trans- mission's shifter out of neutral. 3. The neutral light will turn off to indicate the transfer case is out of neutral. 4. Start the engine and shif tthe automatic transmission to DRIVE to make sure that the vehicle is out of neutral. 5. If the battery is low/dead or the vehicle does not shift out of neutral, set the parking brake until the vehicle can be serviced.

F

G

C D

5L2J-7E385-AA

F67A-7E385-CA F67A-7E385-DA

5L2J-7E385-BA

H

RANGER WITH 4WD AUTOMATIC TRANSMISSION2006

SK3L2J-7H332-AB3L2Z-7H332-AA

PG 2/9

1

cut along dotted line

Drill (2)3/16" Holes

allign with recess

2

5 6

A

7mm

3

B

B

4

B

1

2

3/16"

A

INSTALL TABS INTO HOLESINSTALE LAS TABULACIONES EN LOS AGUJEROS

INSTALLEZ LES TABULATEURS SUR DES TROUS

© Copyright Ford 2005SK3L2J-7H332-AB3L2Z-7H332-AA

PG 3/9

AALOCATE UNUSED GREEN CONNECTORLOCALICE EL CONECTADOR VERDE INUSITADOLOCALISEZ VERT LE CONNECTEUR INUTILISÉ

GREEN CONNECTORVERDE EL CONECTORVERT LE CONNECTEUR

8

8mm

10

8mm

A

11

7mm

12

9

7

AC

1/4"

© Copyright Ford 2005SK3L2J-7H332-AB3L2Z-7H332-AA

PG 4/9

LABEL PLACED ON HEADLINER, CENTERED OFF OF DRIVER’S SUNVISOR

ESCRITURA DE LA ETIQUETA PUESTA EN EL HEADLINER, CENTRADO APAGADO DEL SUNVISOR DEL PROGRAMA PILOTOEITQUETTE PLACEE SUR LE VEDETTE, CENTRE HORS FONCTION DU SUNVISOR DU GESTIONNAIRE

F

OWNER'S GUIDE

The neutral tow feature(NTF) provides the convienience of towing your 4X4vehicle on the rear wheels or on all four wheels for extended distance with-out risking damage to the automatic transmission.

This vehicle has neutral tow capability. To engage the transfer caseinto neutral, follow the procedure listed below. If the transfer case isengaged in neutral, moving the shift lever out of neutral or moving the ignition switch to the ON or Start positions will result in the transfer case shifting out of neutral. Always verify that a low or dead battery condition does not existwhen shifting the transfer case into or out of neutral. Always applythe parking brake and remove the key when the vehicle is in PARK.Failure to follow these instructions could result in unexpected vehiclemovement or transmission damage. When the transfer case is in the neutral position, the engine and transmission are disconnected from the rest of the driveline. Therefore,the vehicle is free to roll. Make sure the vehicle is properly prepared for towing before shifting the transfer case into neutral (see supplement).

TO SHIFT THE TRANSFER CASE INTO NEUTRAL FOR TOWING: 1. Prepare the vehicle for towing. 2. Start the engine to make sure the battery is sufficiently charged. 3. Make sure vehicle is at a complete stop and the vehicle is shifted into two wheel drive 4.Place the automatic transmission shifter into NEUTRAL. 5.Turn the ignition switch to the OFF position (i.e. steering not locked). 6.Depress the brake pedal for 5 seconds. 7. The neutral light will initially go through a bulb check; then stay on to indicate the transfer case is in neutral. 8. Leave ignition switch in the OFF position and the transmission shifter in NEUTRAL while the vehicle is in tow.

DO NOT DISCONNECT TOWED VEHICLE BEFORE PLACING TRANSFER CASE INTO GEAR.

TO SHIFT THE TRANSFER CASE OUT OF NEUTRAL AFTER TOWING

1.Make sure vehicle is at a complete stop. 2. Turn the ignition to the ON (not START) position or move the trans- mission's shifter out of neutral. 3. The neutral light will turn off to indicate the transfer case is out of neutral. 4. Start the engine and shif tthe automatic transmission to DRIVE to make sure that the vehicle is out of neutral. 5. If the battery is low/dead or the vehicle does not shift out of neutral, set the parking brake until the vehicle can be serviced.

E

15

16 17

EXPLORER SPORT & SPORT TRACMODELS ONLY

EXPLORER SPORT & SPORT TRACMODELS ONLY

A D

AGREEN CONNECTORVERDE EL CONECTORVERT LE CONNECTEUR

13 14

© Copyright Ford 2005SK3L2J-7H332-AB3L2Z-7H332-AA

PG 5/9

H

18 19

20 21

EXPLORER SPORT & SPORT TRACMODELS ONLY

EXPLORER SPORT & SPORT TRACMODELS ONLY

EXPLORER SPORT & SPORT TRACMODELS ONLY RANGER MODELS ONLY

22

RANGER MODELS ONLY

23

RANGER MODELS ONLY

H

© Copyright Ford 2005SK3L2J-7H332-AB3L2Z-7H332-AA

PG 6/9

25

26

G

24

RANGER MODELS ONLY RANGER MODELS ONLY

© Copyright Ford 2005SK3L2J-7H332-AB3L2Z-7H332-AA

PG 7/9

27USING NGS SERVICE (GREEN) CARDCONNECT TO VEHICLE VIA THE DIAGNOSTIC CONNECTORSELECT “SERVICE BAY FUNCTIONS”SELECT “4X4 CONTROL MODULE”SELECT “NEUTRAL TOW FUNCTION”SELECT “PROPER VEHICLE AND MODEL YEAR”PRESS TRIGGER AND SCROLL TO ENABLE OR DISABLEPRESS TRIGGER AGAIN AFTER HIGHLIGHTING THE DESIRED STATE PRESS “DONE”

USING NGS+ SELECT PROPER VEHICLE AND MODEL YEARSELECT DIAGNOSTIC DATA LINKSELECT 4X4 MODULESELECT FUNCTION TESTSSELECT NEUTRAL TOW ENABLESCROLL TO ENABLE OR DISABLE NTF AND PRESS TRIGGER

USING WDSCONNECT TO VEHICLE VIA THE DIAGNOSTIC CONNECTORFOLLOW HOOK UP SCREENAFTER WDS DISPLAYS VEHICLE INFO, SELECT TOOL BOX ON TOP OF SCREENFROM ON SCREEN MENU SELECT “MODULE PROGRAMMING”SELECT “PROGRAMMABLE PARAMETTERS”SELECT “NEUTRAL TOW FUNCTION”FOLLOW INSTRUCTIONS ON THE WDS TO COMPLETE OPERATION

FOLLOW INSTRUCTIONS ON THE LABEL ON THE HEADLINER / VISOR LABEL TO ENABLE AND DISABLE NEUTRAL FUNCTION.

PROGRAMMING PROGRAMACION PROGRAMMMATION

USANDO SERVICO DE NGS (VERDE) TARJETACONECTE CON EL VEHICULO VIA DE DIAGNOSTICO EL CONECTORSELECCIONE “LAS FUNCIONES DE LA BAHIA DEL SERVICO”SELECCIONE “EL MODULO DE CONTROL 4X4”SELECT “NEUTRAL TOW FUNCTION”SELECCIONE EL “VEHÍCULO Y MODELO CORRESPONDIENTE”PRESIONE EL DISPARADOR Y ENROLLELO PARA PERMITIR O PARA INVALIDARPRESIONE EL DISPARADOR OTRA VEZ DESPUES DE DESTACAR DESEADO EL ESTADOPRESIONE “HECHO”

EL USAR WDSCONECTE CON EL VEHICULO VIA DE DIAGNOSTICO EL CONNECTOSIGA EL GANCHO ENCIMA DE LA PANTALLADESPUES DE QUE WDS VISUALICE EL VEHICULO INFO,SELECCIONE EL “RECTANGULO DE LA HERRAMIENTA”ENCIMA DE LA PANTALLASELECCIONE LOS “PARAMETROS PROGRAMABLES”SELECCIONE LA “FUNCION NEUTRAL DEL REMOLQUE”SIGA LAS INSTRUCCIONES EN EL WDS DE TERMINAR LA OPERACIONSIGA LAS INSTRUCCIONES EN LA ESCRITURA DE LA ETIQUETA EN LA ESCRITURA DE LA ETIQUETA DEL HEADLINER / DEL VISERA DE PERMITIR Y DE INVALIDAR LA FUNCION NEUTRAL.

EN UTILISANT LE SERVICE DE NGS (VERTE) CARTERELIEZ AU VEHICULE PAR L’INTERMEDIARE DIAGNOSTIQUE DU CONNECTEURCHOISISSEZ “LES FONCTIONS DE COMPARTIMENT DE SERVICE”CHOISISSEZ “LA MODULE DE COMMANDE 4X4”CHOISISSEZ “LA FONCTION NEUTRE DE REMORQUAGE”CHOISISSEZ L”L'ANNÉE-MODÈLE ET LA MARQUE DE VOTRE VÉHICULE”APPUYEZ LE DECLENCHEMENT ET LE FAITES DEFILER POUR PERMETTRE OU INVALIDERAPPUYEZ LE DECLENCHEMENT ENCORE APRES AVOIR MIS EN VALEUR DESIRE L’ETATAPPUYEZ “FAIT”.

UTILISATION WDSRELIEZ AU VEHICULE PAR L’INTERMEDIAIRE DU DIAGNOSTIC CONNECTOSUIVEZ LA CONNEXION L’ECRANAPRES QUE WDS AFFICHE L’INFORMATION DE VEHICULE,CHOISISSEZ L’”CADRE D’ OUTIL” SUR L’ECRANCHOISISSEZ “LES PARAMETRES PROGRAMMABLES”CHOISISSEZ “LA FONCTION NEUTRE DE REMORQUAGE”SUIVEZ LES INSTRUCTIONS SUR LE WDS DE TERMINER L’EXECUTION

SUIVEZ LES INSTRUCTIONS SUR L’ETIQUETTE SUR L’ETIQUETTE DE VEDETTE / PARE SOLEIL DE PERMETTRE ET INVALIDER LA FONCTION NEUTRE.

UTILIZANDO NGS+SELECCIONE VEHÍCULO Y MODELO CORRESPONDIENTESELECCIONE DIAGNOSTIC DATA LINK (ENLACE DE DATOS DE DIAGNÓSTICO)SELECCIONE 4X4 MODULE (MÓDULO 4X4)SELECCIONE FUNCTION TESTS (PRUEBAS DE FUNCIÓN)SELECCIONE NEUTRAL TOW ENABLE (ACTIVAR REMOLQUE NEUTRAL)DESPLACE PARA ACTIVAR (ENABLE) O DESACTIVAR (DISABLE) LA FUNCIÓN DE REMOLQUE NEUTRAL Y PRESIONE EL DISPARADOR

UTILISER LA CARTE (VERTE) NGS SÉLECTIONNER L'ANNÉE-MODÈLE ET LA MARQUE DE VOTRE VÉHICULE SÉLECTIONNER DIAGNOSTIC DATA LINK (LIEN DE DONNÉES DE DIAGNOSTIC)SÉLECTIONNER 4X4 MODULESÉLECTIONNER FUNCTION TESTS (TESTS DE FONCTION)SÉLECTIONNER NEUTRAL TOW ENABLE (ACTIVER REMORQUAGE POINT MORT)ACTIVER OU DÉSACTIVER LE REMORQUAGE AU POINT MORT (NTF) ET APPUYER SURLA GÂCHETTE

© Copyright Ford 2005SK3L2J-7H332-AB3L2Z-7H332-AA

PG 8/9

C281b

White / YellowBlanco / Amarilla

Blanc / Jaune

Bater a +Batterie +

1

8

9

17

3

#25 7.5A

Battery +

BlackNegroNoir

LT B

lue

/ Yel

low

Azu

l Cla

ro /

Am

arill

a L

ger

Ble

u /

Jau

ne

4 X 4 Module

Neutral Tow Display

2 Pin Connection

Pin 3

El M dulo 4X44X4 Module

2 Connexion d 'Epingle2 Connexion d 'Epingle

El Despliegue neutral del RemolqueL'Exposition de Tow neutre

Black - C

atho

de

Red

- An

od

e

1440

1 H

arn

ess

El alfiler 3L 'Epingle 3

Neg

ro - C

tod

oN

oir - la C

atho

de

Ro

jo - A

no

do

Ro

ug

e - l'An

od

e

1440

1 E

nja

ezan

1440

1 E

xplo

iten

t

RedRojo

Rouge

28

© Copyright Ford 2005SK3L2J-7H332-AB3L2Z-7H332-AA

Congratulations!You've purchased a Genuine Ford Brand Accessory designed, engineered, and builtspecifically for your Ford vehicle. We have made every effort to ensure that the Neutral TowIndicator is top quality in terms of fit, durability, finish and ease of installation.

At Ford Customer Service Division,customer satisfaction is our number one priority!

¡Felicidades!Acaba de comprar un Accesorio marca Ford Genuino, diseñado y construidoespecíficamente para su vehículo Ford. Hemos realizado todos los esfuerzos

necesarios para que este Indicador Neutral Del Remolque sean de la mejor calidad encuanto a ajuste, durabilidad, acabado y facilidad de instalación.

¡Para la División de Atención al Cliente de Ford, la satisfacción del cliente es nuestraprincipal prioridad!

Félicitations !Vous avez acheté un accessoire Ford d'origine, conçu et réalisé spécialement pour

votre véhicule Ford. Nous avons tout mis en œuvre pour que ces Indicateur Neutre DeRemorquage soit de la plus haute qualité au niveau de l'adaptabilité, de la durabilité

de la finition et de la facilité d'installation.

Dans la division du service après-vente Ford, la satisfaction du client a priorité absolue !

PG 9/9 © Copyright Ford 2005SK3L2J-7H332-AB3L2Z-7H332-AA