23
Experion PKS R500.2 Server Patch 1 and Quick Builder Patch 1 Software Change Notice Revision Date: October 5, 2017

Experion PKS - Honeywell · Start -> Honeywell Experion Tools -> Experion PKS Services Control Panel). Once started, select “Stop All services” and click OK to stop all Experion

  • Upload
    lyxuyen

  • View
    437

  • Download
    31

Embed Size (px)

Citation preview

Page 1: Experion PKS - Honeywell · Start -> Honeywell Experion Tools -> Experion PKS Services Control Panel). Once started, select “Stop All services” and click OK to stop all Experion

Experion PKS

R500.2 Server Patch 1 and Quick Builder Patch 1

Software Change Notice

Revision Date: October 5, 2017

Page 2: Experion PKS - Honeywell · Start -> Honeywell Experion Tools -> Experion PKS Services Control Panel). Once started, select “Stop All services” and click OK to stop all Experion

Server Patch 1 and Quick Builder Patch 1 Release R500.2 Software Change Notice ii

Notices and Trademarks

© Honeywell International Sàrl 2017. All Rights Reserved.

While this information is presented in good faith and believed to be accurate, Honeywell

disclaims the implied warranties of merchantability and fitness for a particular purpose and

makes no express warranties except as may be stated in its written agreement with and for its

customer.

In no event is Honeywell liable to anyone for any indirect, special or consequential damages.

The information and specifications in this document are subject to change without notice.

Honeywell PlantScape, Experion, and TotalPlant are US registered trademarks of Honeywell

International Inc.

Other brand or product names are trademarks of their respective owners.

Honeywell Process Solutions

1860 West Rose Garden Lane

Phoenix, AZ 85027 USA

1-800 822-7673

Page 3: Experion PKS - Honeywell · Start -> Honeywell Experion Tools -> Experion PKS Services Control Panel). Once started, select “Stop All services” and click OK to stop all Experion

Server Patch 1 and Quick Builder Patch 1 Release R500.2 Software Change Notice iii

Page 4: Experion PKS - Honeywell · Start -> Honeywell Experion Tools -> Experion PKS Services Control Panel). Once started, select “Stop All services” and click OK to stop all Experion

Server Patch 1 and Quick Builder Patch 1 Release R500.2 Software Change Notice iv

Symbol Definitions

The following table lists those symbols used in this document to denote certain conditions.

Symbol Definition

ATTENTION: Identifies information that requires special

consideration.

Page 5: Experion PKS - Honeywell · Start -> Honeywell Experion Tools -> Experion PKS Services Control Panel). Once started, select “Stop All services” and click OK to stop all Experion

Server Patch 1 and Quick Builder Patch 1 Release R500.2 Software Change Notice v

Table of Contents

1 Introduction.........................................................................................................................7

1.1 About the document ......................................................................................................7

1.2 About the patch .............................................................................................................7

1.2.1 Problems resolved .................................................................................................7

1.2.2 Known Issues ........................................................................................................7

1.2.3 Limitations .............................................................................................................7

1.3 Before you begin ...........................................................................................................8

1.3.1 Prerequisites ..........................................................................................................8

1.3.2 Patch installation or migration checklist..................................................................8

1.3.3 Applicable nodes ...................................................................................................8

1.3.4 Applicable modules ................................................................................................9

1.3.5 Supported controller migration paths ...................................................................10

1.3.6 Verify the present version on the node .................................................................10

1.3.7 Copying and extracting the patch .........................................................................10

1.4 Change impact ............................................................................................................10

1.4.1 Control change impact .........................................................................................10

1.4.2 Operational change impact ..................................................................................11

1.4.3 Infrastructure change impact ................................................................................11

2 Patch installation ..............................................................................................................12

2.1 Installing the patch on Backup Control Center Server .................................................12

2.1.1 To install the patch ...............................................................................................12

2.1.2 To validate the patch installation ..........................................................................12

2.2 Installing the patch on Redundant Experion Server (ESV) & Redundant Server TPN

Connected (ESVT) .................................................................................................................13

2.2.1 To install the patch ...............................................................................................13

2.2.2 To validate the patch installation ..........................................................................13

2.3 Installing the patch on Non-Redundant Experion Server (ESV) , Non-Redundant

Server TPN Connected (ESVT) , and Application Server (EAS) ............................................14

2.3.1 To install the patch ...............................................................................................14

Page 6: Experion PKS - Honeywell · Start -> Honeywell Experion Tools -> Experion PKS Services Control Panel). Once started, select “Stop All services” and click OK to stop all Experion

Server Patch 1 and Quick Builder Patch 1 Release R500.2 Software Change Notice vi

2.3.2 To validate the patch installation ..........................................................................14

2.4 Installing the patch on Console Station (ES-C), Console Station TPN Connected (ES-

T), Console Extension Station (ES-CE), Flex Station (ES-F), and Remote Engineering and

Station Server (RESS) ...........................................................................................................15

2.4.1 To install the patch ...............................................................................................15

2.4.2 To validate the patch installation ..........................................................................15

2.5 Migrating controllers ....................................................................................................16

3 Patch removal ...................................................................................................................17

3.1 Removing the patch on Backup Control Center Server ...............................................17

3.1.1 To stop the services .............................................................................................17

3.1.2 To remove the patch ............................................................................................17

3.1.3 To validate the patch removal ..............................................................................17

3.2 Removing the patch on Redundant Experion Server (ESV) & Redundant Server TPN

Connected (ESVT) .................................................................................................................18

3.2.1 To stop the services .............................................................................................18

3.2.2 To remove the patch ............................................................................................18

3.2.3 To validate the patch removal ..............................................................................18

3.3 Removing the patch on Non-Redundant Experion Server (ESV), Non-Redundant

Server TPN Connected (ESVT), and Application Server (EAS) .............................................19

3.3.1 To stop the services .............................................................................................19

3.3.2 To remove the patch ............................................................................................19

3.3.3 To validate the patch removal ..............................................................................19

3.4 Removing the patch on Console Station (ES-C), Console Station TPN Connected (ES-

T) , Console Extension Station (ES-CE), Flex Station (ES-F), and Remote Engineering and

Station Server (RESS) ...........................................................................................................20

3.4.1 To stop the services .............................................................................................20

3.4.2 To remove the patch ............................................................................................20

3.4.3 To validate the patch removal ..............................................................................20

4 Additional information .....................................................................................................21

4.1 Additional information to validate patch installation .....................................................21

4.1.1 Firmware revision ................................................................................................21

5 GTAC Support ...................................................................................................................22

Page 7: Experion PKS - Honeywell · Start -> Honeywell Experion Tools -> Experion PKS Services Control Panel). Once started, select “Stop All services” and click OK to stop all Experion

Server Patch 1 and Quick Builder Patch 1 Release R500.2 Software Change Notice 7

1 Introduction

1.1 About the document

The Software Change Notice describes the prerequisites, resolved PARs, applicable nodes,

and steps to install/uninstall the patch. Additionally, the SCN contains information about the

change impact and additional information for this patch. The latest version of this SCN is always

available on the Honeywell Process Solutions website.

1.2 About the patch

This patch addresses problems and offers improvements requested since the release of

Experion PKS R500.2. These fixes will be included in point release R500.3. It is recommended

to move to this once it is available.

1.2.1 Problems resolved

This patch resolves the following PARs.

PAR Subsystem Description of problem

1-87EOXPZ Enron

Modbus

Interface

Enron Modbus interface support for transport of Modbus TCP

over UDP

1-87DZ0UN Licence

Management

Can't sync servers after changing the locale to Arabic (Bahrain)

or Greek (Greece)

1-86BHJUZ Display

Subsystem

Setting a value via script data takes longer than expected to

get reflected back to the display.

1.2.2 Known Issues

None

1.2.3 Limitations

1.2.3.1 Patch removal

[] Automatic [ ] Can be done manually

during next upgrade

[ ] Must be done manually

before next upgrade

Page 8: Experion PKS - Honeywell · Start -> Honeywell Experion Tools -> Experion PKS Services Control Panel). Once started, select “Stop All services” and click OK to stop all Experion

Server Patch 1 and Quick Builder Patch 1 Release R500.2 Software Change Notice 8

1.2.3.2 Patch distribution

[] Not Limited [ ] Limited for:

1.2.3.3 Localization

[] Not impacted [ ] Patch may contain strings

in English. A Localization

version to be included in the

next release.

1.2.3.4 Cumulative patch

[] Yes.

See Prerequisites

[ ] No

1.3 Before you begin

1.3.1 Prerequisites

The patch must be installed on a node on which the following updates are installed.

Experion PKS R500.2

1.3.2 Patch installation or migration checklist

Task order Task Reference

1 Prerequisites See section Prerequisites

2 Applicable nodes See section Applicable nodes

3 Installing the patch See section Patch installation

1.3.3 Applicable nodes

This patch is applicable for the following nodes.

Node Is the patch

applicable?

Server (ESV) Yes

Page 9: Experion PKS - Honeywell · Start -> Honeywell Experion Tools -> Experion PKS Services Control Panel). Once started, select “Stop All services” and click OK to stop all Experion

Server Patch 1 and Quick Builder Patch 1 Release R500.2 Software Change Notice 9

Node Is the patch

applicable?

Server TPN Connected (ESVT) Yes

eServer No

Application Control Environment (ACE) No

Application Control Environment TPN Connected (ACE-T) No

Simulation Control Environment (SCE) No

Console Station (ES-C) Yes

Console Station TPN Connected (ES-T) Yes

Console Extension Station (ES-CE) Yes

Flex Station (ES-F) Yes

Experion Hiway Gateway (EHG) No

APP Node (E-APP) No

Application Server (EAS) Yes

Remote Engineering and Station Server (RESS) Yes

1.3.4 Applicable modules

This patch is applicable for the following modules.

Node Is the patch

applicable?

C200 controller No

C200E controller No

C300 controller No

Fieldbus Interface Module No

Fieldbus Interface Module 4 No

Fieldbus Interface Module 8 No

Fault Tolerant Ethernet Bridge Module (FTEB) No

Serial I/O Module (IOM) No

Legacy I/O Module (LIOM) No

PROFIBUS Gateway Module (PGM) No

Page 10: Experion PKS - Honeywell · Start -> Honeywell Experion Tools -> Experion PKS Services Control Panel). Once started, select “Stop All services” and click OK to stop all Experion

Server Patch 1 and Quick Builder Patch 1 Release R500.2 Software Change Notice 10

Node Is the patch

applicable?

SeriesC IO Module No

1.3.5 Supported controller migration paths

Not Applicable

1.3.6 Verify the present version on the node

To verify the present version on the node, perform the following steps.

1. Using Notepad, open the ProductVersion.txt file located in the following path. <install folder>\Honeywell\Experion PKS\ProductVersion.txt.

2. Verify the ProductVersion.txt for the following: If the following line is present, the node has the appropriate product version to install this patch. +Experion PKS R500.2 Install completed on MM/DD/YYYY HH:MM:SS

Note: <install folder> is the location where Experion is installed. For default installations this is

C:\Program Files (x86).

1.3.7 Copying and extracting the patch

Perform the following steps to copy and extract the patch.

1. For each node that needs to be updated, copy Experion PKS R500.2 Server Patch 1 and Quick Builder Patch 1.zip to a temporary folder on your hard disk.

2. Extract files to a temporary folder on your hard disk.

3. Zip file contains:

a. Experion PKS R500.2 Server Patch 1.exe

b. Experion PKS R500.2 Server Patch 1.xml

c. Experion PKS R500.2 Server Patch 1_Contents.txt

d. Experion PKS R500.2 QuickBuilder Patch1.exe

e. Experion PKS R500.2 QuickBuilder Patch1.xml

f. Experion PKS R500.2 Server Patch 1 and Quick Builder Patch 1_SCN.pdf

g. experion_wrapper.exe

h. experion_wrapper.xml

1.4 Change impact

1.4.1 Control change impact

Not Applicable

Page 11: Experion PKS - Honeywell · Start -> Honeywell Experion Tools -> Experion PKS Services Control Panel). Once started, select “Stop All services” and click OK to stop all Experion

Server Patch 1 and Quick Builder Patch 1 Release R500.2 Software Change Notice 11

1.4.2 Operational change impact

PAR 1-5GDV07P

Description: Unable to perform a data entry on an alphanumeric that has a data binding as well as script

data binding.

Impact: This PAR addresses an issue where an alphanumeric that is directly bound to data as well as

using script data would have issues with data entry if a script data write occurred at the same time.

For this fix to work correctly, the server wide setting “Scripts act as Operator” needs to be set to off.

1.4.3 Infrastructure change impact

Not Applicable

Page 12: Experion PKS - Honeywell · Start -> Honeywell Experion Tools -> Experion PKS Services Control Panel). Once started, select “Stop All services” and click OK to stop all Experion

Server Patch 1 and Quick Builder Patch 1 Release R500.2 Software Change Notice 12

2 Patch installation

ATTENTION

Please ensure the order in which the patch is applied to each node, follows the order

as documented in the below patch installation instructions.

2.1 Installing the patch on Backup Control Center Server

2.1.1 To install the patch

1. Ensure the Primary and all Backup Server databases are synchronized and there is no alarm indicating that the event replication has failed before proceeding.

2. The Backup Server in the following steps refers to the Backup Server in the Active Server Location

3. On the Backup Server log in using an account that is a member of both the Windows Administrators and Product Administrators group.

4. Ensure no instances of Station, Display Builder, Configuration Studio, Quick Builder, HMIWeb Display Builder, the Diagnostic Capture Tool or Microsoft Excel are running.

5. On the Backup Server, start the Experion PKS Services Control Panel program (from Start -> Honeywell Experion Tools -> Experion PKS Services Control Panel). Once started, select “Stop All services” and click OK to stop all Experion services.

6. Click Exit to exit the Experion PKS Services Control Panel program. 7. Navigate to the software patch package, right click experion_wrapper.exe and choose

Run as Administrator 8. Click Yes when prompt asked if you want to allow the patch to run. 9. Click OK when asked if you want to install the following update. A Command Prompt

window with the text “Installing patch…” and a few windows installer dialogs will appear. 10. After successful install, reboot the system following the popup 11. Synchronize Primary and Backup Server databases 12. Fail over the Primary Server to the Backup Server in the Active Server Location 13. Synchronize Primary and Backup Server databases 14. Validate that the System is healthy 15. Repeat steps 3. to 11. on the new Backup Server in the Active Server Location 16. Repeat steps 3. to 11. on Server A in the Backup Server Location 17. Repeat steps 3. to 11. on Server B in the Backup Server Location

Notes:

i) If the software patch installer reports that some programs must be closed before installing, click “OK” to accept this and let the installer to terminate these programs. Otherwise, click “Cancel” to abort installation.

2.1.2 To validate the patch installation

To verify the successful installation of the patch:

a) Using Notepad, open the ProductVersion.txt file located in the following path:

Page 13: Experion PKS - Honeywell · Start -> Honeywell Experion Tools -> Experion PKS Services Control Panel). Once started, select “Stop All services” and click OK to stop all Experion

Server Patch 1 and Quick Builder Patch 1 Release R500.2 Software Change Notice 13

<install folder>\Honeywell\Experion PKS\ProductVersion.txt

b) Verify that the file contains an entry starting with: “++ <name of patch> installed on <install date & time>”

After successful installation, the files extracted for installation are no longer needed. Delete the temporary folder and its files.

2.2 Installing the patch on Redundant Experion Server (ESV) &

Redundant Server TPN Connected (ESVT)

2.2.1 To install the patch

1. Ensure the Primary and Backup Server databases are synchronized and there is no alarm indicating that the event replication has failed before proceeding.

2. On Backup Server log in using an account that is a member of both the Windows Administrators and Product Administrators group.

3. Ensure no instances of Station, Display Builder, Configuration Studio, Quick Builder, HMIWeb Display Builder, the Diagnostic Capture Tool or Microsoft Excel are running.

4. On the Backup Server, start the Experion PKS Services Control Panel program (from Start -> All Programs -> Honeywell Experion PKS -> Experion PKS Services Control Panel). Once started, select “Stop All services” and click OK to stop all Experion services.

5. Click Exit to exit the Experion PKS Services Control Panel program. 6. Navigate to the software patch package, right click experion_wrapper.exe and choose

Run as Administrator 7. Click Yes when prompt asked if you want to allow the patch to run. 8. Click OK when asked if you want to install the following update. A Command Prompt

window with the text “Installing patch…” and a few windows installer dialogs will appear. 9. Once the patch installation is finished, click Ok to close the dialog. 10. After successful install, reboot the system following the popup 11. Synchronize Primary and Backup Server databases 12. Fail over the Primary Server to the Backup Server 13. Repeat steps 2. to 11. on the new Backup Server

Notes:

i) If the software patch installer reports that some programs must be closed before installing, click “OK” to accept this and let the installer to terminate these programs. Otherwise, click “Cancel” to abort installation.

2.2.2 To validate the patch installation

To verify the successful installation of the patch:

a) Using Notepad, open the ProductVersion.txt file located in the following path:

Page 14: Experion PKS - Honeywell · Start -> Honeywell Experion Tools -> Experion PKS Services Control Panel). Once started, select “Stop All services” and click OK to stop all Experion

Server Patch 1 and Quick Builder Patch 1 Release R500.2 Software Change Notice 14

<install folder>\Honeywell\Experion PKS\ProductVersion.txt

b) Verify that the file contains an entry starting with: “++ <name of patch> installed on <install date & time>”

After successful installation, the files extracted for installation are no longer needed. Delete

the temporary folder and its files.

2.3 Installing the patch on Non-Redundant Experion Server (ESV) ,

Non-Redundant Server TPN Connected (ESVT) , and Application

Server (EAS)

2.3.1 To install the patch

ATTENTION

Installation of this patch requires the Experion Server to be stopped, therefore no view

or control of the process is available during the installation.

1. Log in using an account that is a member of both the Windows Administrators and

Product Administrators group. 2. Ensure no instances of Station, Display Builder, Configuration Studio, Quick Builder,

HMIWeb Display Builder, the Diagnostic Capture Tool or Microsoft Excel are running. 3. Start the Experion PKS Services Control Panel program (from Start -> All Programs ->

Honeywell Experion PKS -> Experion PKS Services Control Panel). Once started, select “Stop All services” and click OK to stop all Experion services.

4. Click Exit to exit the Experion PKS Services Control Panel program. 5. Navigate to the software patch package, right click experion_wrapper.exe and choose

Run as Administrator 6. Click Yes when prompt asked if you want to allow the patch to run. 7. Click OK when asked if you want to install the following update. A Command Prompt

window with the text “Installing patch…” and a few windows installer dialogs will appear. 8. Once the patch installation is finished, click Ok to close the dialog. 9. After successful install, reboot the system following the popup

Notes:

i) If the software patch installer reports that some programs must be closed before installing, click “OK” to accept this and let the installer to terminate these programs. Otherwise, click “Cancel” to abort installation.

2.3.2 To validate the patch installation

To verify the successful installation of the patch:

a) Using Notepad, open the ProductVersion.txt file located in the following path: <install folder>\Honeywell\Experion PKS\ProductVersion.txt

b) Verify that the file contains an entry starting with:

Page 15: Experion PKS - Honeywell · Start -> Honeywell Experion Tools -> Experion PKS Services Control Panel). Once started, select “Stop All services” and click OK to stop all Experion

Server Patch 1 and Quick Builder Patch 1 Release R500.2 Software Change Notice 15

“++ <name of patch> installed on <install date & time>”

After successful installation, the files extracted for installation are no longer needed. Delete

the temporary folder and its files.

2.4 Installing the patch on Console Station (ES-C), Console Station

TPN Connected (ES-T), Console Extension Station (ES-CE), Flex

Station (ES-F), and Remote Engineering and Station Server

(RESS)

2.4.1 To install the patch

1. Log in using an account that is a member of both the Windows Administrators and

Product Administrators group. 2. Ensure no instances of Station, Display Builder, Configuration Studio, Quick Builder,

HMIWeb Display Builder, the Diagnostic Capture Tool or Microsoft Excel are running. 3. Start the Experion PKS Services Control Panel program (from Start -> All Programs ->

Honeywell Experion PKS -> Experion PKS Services Control Panel). Once started, select “Stop All services” and click OK to stop all Experion services.

4. Click Exit to exit the Experion PKS Services Control Panel program. 5. Navigate to the software patch package, right click experion_wrapper.exe and choose

Run as Administrator. 6. Click Yes when prompt asked if you want to allow the patch to run. 7. Click OK when asked if you want to install the following update. A Command Prompt

window with the text “Installing patch…” and a few windows installer dialogs will appear. 8. Once the patch installation is finished, click Ok to close the dialog. 9. After successful install, reboot the system following the popup

Notes:

i) If the software patch installer reports that some programs must be closed before installing, click “OK” to accept this and let the installer to terminate these programs. Otherwise, click “Cancel” to abort installation.

2.4.2 To validate the patch installation

To verify the successful installation of the patch:

a) Using Notepad, open the ProductVersion.txt file located in the following path: <install folder>\Honeywell\Experion PKS\ProductVersion.txt

b) Verify that the file contains an entry starting with: “++ <name of patch> installed on <install date & time>”

After successful installation, the files extracted for installation are no longer needed. Delete

the temporary folder and its files.

Page 16: Experion PKS - Honeywell · Start -> Honeywell Experion Tools -> Experion PKS Services Control Panel). Once started, select “Stop All services” and click OK to stop all Experion

Server Patch 1 and Quick Builder Patch 1 Release R500.2 Software Change Notice 16

2.5 Migrating controllers

Not Applicable

Page 17: Experion PKS - Honeywell · Start -> Honeywell Experion Tools -> Experion PKS Services Control Panel). Once started, select “Stop All services” and click OK to stop all Experion

Server Patch 1 and Quick Builder Patch 1 Release R500.2 Software Change Notice 17

3 Patch removal

3.1 Removing the patch on Backup Control Center Server

3.1.1 To stop the services

1. Close and exit all Experion PKS application. 2. In Window, click on Start -> All Programs -> Honeywell Experion PKS -> Experion PKS

Services Control Panel 3. Click Yes in the User Account Control dialog to launch the utility. 4. Select “Stop All Services” and click OK. 5. Click on exit to exit the tool once all services have been stopped.

3.1.2 To remove the patch

1. The Backup Server in the following steps refers to the Backup Server in the Active Server Location

2. On the Backup Server, in Windows, right click on Start -> All Programs -> Honeywell Experion PKS -> Maintenance Tools and select “Run as administrator”.

3. Click Yes when prompted to run the program. 4. Click on “View/Modify Experion Product”. 5. Click on “View/Uninstall Experion Updates”. 5. Locate the patch to remove and click on the “Remove” button. 6. Follow the prompts on screen to uninstall the patch. 7. Once the uninstallation completed, an uninstallation successfully completed dialog box

will popup. 8. Restart the machine 9. Synchronize primary and backup server databases. 10. Validate that the System is healthy 11. Repeat steps 2. to 9. on Server A in the Backup Server Location 12. Repeat steps 2. to 9. on Server B in the Backup Server Location 13. Fail over the primary server to the backup server in the Active Server Location. The

backup server will become primary and the primary server become backup. 14. Synchronize primary and backup server databases. 15. Repeat steps 2. to 9. on the new Backup Server in the Active Server Location 16. Synchronize primary and backup server databases 17. Uninstall is completed.

3.1.3 To validate the patch removal

a) Using Notepad, open the ProductVersion.txt file located in the following path: <install folder>\Honeywell\Experion PKS\ProductVersion.txt

b) Verify that the file contains an entry starting with: “- - <name of patch>uninstalled on <install date & time>”

Page 18: Experion PKS - Honeywell · Start -> Honeywell Experion Tools -> Experion PKS Services Control Panel). Once started, select “Stop All services” and click OK to stop all Experion

Server Patch 1 and Quick Builder Patch 1 Release R500.2 Software Change Notice 18

3.2 Removing the patch on Redundant Experion Server (ESV) &

Redundant Server TPN Connected (ESVT)

3.2.1 To stop the services

1. Close and exit all Experion PKS application. 2. In Window, click on Start -> All Programs -> Honeywell Experion PKS -> Experion PKS

Services Control Panel 3. Click Yes in the User Account Control dialog to launch the utility. 4. Select “Stop All Services” and click OK. 5. Click on exit to exit the tool once all services have been stopped.

3.2.2 To remove the patch

1. On the Backup Server, in Windows, right click on Start -> All Programs -> Honeywell Experion PKS -> Maintenance Tools and select “Run as administrator”.

2. Click Yes when prompted to run the program. 3. Click on “View/Modify Experion Product”. 4. Click on “View/Uninstall Experion Updates”. 5. Locate the patch to remove and click on the “Remove” button. 6. Follow the prompts on screen to uninstall the patch. 7. Once the uninstallation completed, an uninstallation successfully completed dialog box

will popup. 8. Restart the machine. 9. Synchronize primary and backup server databases. 10. Fail over the primary server to the backup server. The backup server will become

primary and the primary server become backup. 11. Repeat Steps 1-9 on the new backup. 12. Synchronize primary and backup server databases 13. Uninstall is completed.

3.2.3 To validate the patch removal

a) Using Notepad, open the ProductVersion.txt file located in the following path: <install folder>\Honeywell\Experion PKS\ProductVersion.txt

b) Verify that the file contains an entry starting with: “- - <name of patch>uninstalled on <install date & time>”

Page 19: Experion PKS - Honeywell · Start -> Honeywell Experion Tools -> Experion PKS Services Control Panel). Once started, select “Stop All services” and click OK to stop all Experion

Server Patch 1 and Quick Builder Patch 1 Release R500.2 Software Change Notice 19

3.3 Removing the patch on Non-Redundant Experion Server (ESV),

Non-Redundant Server TPN Connected (ESVT), and Application

Server (EAS)

ATTENTION

Installation of this patch requires the Experion Server to be stopped, therefore no view

or control of the process is available during the installation.

3.3.1 To stop the services

1. Close and exit all Experion PKS application. 2. In Window, click on Start -> All Programs -> Honeywell Experion PKS -> Experion PKS

Services Control Panel 3. Click Yes in the User Account Control dialog to launch the utility. 4. Select “Stop All Services” and click OK. 5. Click on exit to exit the tool once all services have been stopped.

3.3.2 To remove the patch

1. In Windows, right click on Start -> All Programs -> Honeywell Experion PKS -> Maintenance Tools and select “Run as administrator”.

2. Click Yes when prompted to run the program. 3. Click on “View/Modify Experion Product”. 4. Click on “View/Uninstall Experion Updates”. 5. Locate the patch to remove and click on the “Remove” button. 6. Follow the prompts on screen to uninstall the patch. 7. Once the uninstallation completed, an uninstallation successfully completed dialog box

will popup. 8. If prompted, restart the machine. 9. In Windows, click on Start -> All Programs -> Honeywell Experion PKS -> Experion PKS

Services Control Panel 10. Select “Start All Services” and click OK. 11. Uninstall is completed.

3.3.3 To validate the patch removal

a) Using Notepad, open the ProductVersion.txt file located in the following path: <install folder>\Honeywell\Experion PKS\ProductVersion.txt

b) Verify that the file contains an entry starting with: “- - <name of patch>uninstalled on <install date & time>”

Page 20: Experion PKS - Honeywell · Start -> Honeywell Experion Tools -> Experion PKS Services Control Panel). Once started, select “Stop All services” and click OK to stop all Experion

Server Patch 1 and Quick Builder Patch 1 Release R500.2 Software Change Notice 20

3.4 Removing the patch on Console Station (ES-C), Console Station

TPN Connected (ES-T) , Console Extension Station (ES-CE), Flex

Station (ES-F), and Remote Engineering and Station Server

(RESS)

3.4.1 To stop the services

1. Close and exit all Experion PKS application. 2. In Window, click on Start -> All Programs -> Honeywell Experion PKS -> Experion PKS

Services Control Panel 3. Click Yes in the User Account Control dialog to launch the utility. 4. Select “Stop All Services” and click OK. 5. Click on exit to exit the tool once all services have been stopped.

3.4.2 To remove the patch

1. In Windows, right click on Start -> All Programs -> Honeywell Experion PKS -> Maintenance Tools and select “Run as administrator”.

2. Click Yes when prompted to run the program. 3. Click on “View/Modify Experion Product”. 4. Click on “View/Uninstall Experion Updates”. 5. Locate the patch to remove and click on the “Remove” button. 6. Follow the prompts on screen to uninstall the patch. 7. Once the uninstallation completed, an uninstallation successfully completed dialog box

will popup. 8. If prompted, restart the machine. 9. In Windows, click on Start -> All Programs -> Honeywell Experion PKS -> Experion PKS

Services Control Panel 10. Select “Start All Services” and click OK. 11. Uninstall is completed.

3.4.3 To validate the patch removal

a) Using Notepad, open the ProductVersion.txt file located in the following path: <install folder>\Honeywell\Experion PKS\ProductVersion.txt

b) Verify that the file contains an entry starting with: “- - <name of patch>uninstalled on <install date & time>”

Page 21: Experion PKS - Honeywell · Start -> Honeywell Experion Tools -> Experion PKS Services Control Panel). Once started, select “Stop All services” and click OK to stop all Experion

Server Patch 1 and Quick Builder Patch 1 Release R500.2 Software Change Notice 21

4 Additional information

4.1 Additional information to validate patch installation

4.1.1 Firmware revision

Not Applicable

Page 22: Experion PKS - Honeywell · Start -> Honeywell Experion Tools -> Experion PKS Services Control Panel). Once started, select “Stop All services” and click OK to stop all Experion

Server Patch 1 and Quick Builder Patch 1 Release R500.2 Software Change Notice 22

5 GTAC Support

Subscribe for Automated Email Alerts: Honeywell advises all users to subscribe for alerts on HoneywellProcess.com to receive an email alert every time a new Notification or patch is posted. A tutorial is available (“Learn to Subscribe” link at the bottom right hand side of any page of HoneywellProcess.com) to help guide you through the subscription process and to tailor subscriptions to be appropriate to your system and needs. In addition you may also Subscribe to the GTAC Knowledge Sharing Mails which provide users on a regular basis with valuable tips & tricks, lessons learned and recommendations.

Further support required? If you have any questions concerning this notification, please contact your local Honeywell office or the

Global Technical Assistance Centre (GTAC). Visit HoneywellProcess.Com and select “Contact Us” for

country-specific Customer Contact Numbers. After you log on to HoneywellProcess.Com you may also

Search our Knowledge Base or Submit a Support Request to request help.

Page 23: Experion PKS - Honeywell · Start -> Honeywell Experion Tools -> Experion PKS Services Control Panel). Once started, select “Stop All services” and click OK to stop all Experion

Honeywell Process Solutions

1860 West Rose Garden Lane

Phoenix, AZ 85027 USA