EW0-200

8/13/2019 EW0-200

1/60

Exam : EW0-200

Title : Extreme Networks Associate Ver : 08.13.08

8/13/2019 EW0-200

2/60

8/13/2019 EW0-200

3/60

8/13/2019 EW0-200

4/60

EW0-200

Actualtests.com - The Power of Knowing

QUESTION 7:

Which step would you take to configure a VLAN to only allow IP-related traffic?

A. config protocol ip

B. config protocol ipC. config ip protocol D. None of these.

Answer: A

QUESTION 8:

Extreme Networks switches build their forwarding database from the incoming packetfield information containing the:

A. Source MAC address.B. Destination MAC address.C. Source IP address.D. Destination IP address.

Answer: A

QUESTION 9:

The CLI console port utilizes a serial cable for physical switch to terminal connection.

A. TRUEB. FALSE

Answer: A

QUESTION 10:

Which CLI command will you use to change the CLI prompt from the default display toSwitch02?

A. CONFIG SNMP SYSLOCATION Switch02B. CONFIG SNMP SYSNAME Switch02C. CONFIG CLI PROMPT Switch02D. CONFIG CLI DISPLAY Switch02

Answer: B

QUESTION 11:

8/13/2019 EW0-200

5/60

EW0-200


In spanning tree, the designated bridge is the bridge with the:

A. least-cost path to the root bridgeB. highest bridge priorityC. lowest port cost on all ports

D. None of theseAnswer: A

QUESTION 12:

In ExtremeWare, active VLANs that are configured with ports and an IP address andconfigured to forward IP and run a routing protocol will have their subnet advertised.

A. TRUEB. FALSE

Answer: A

QUESTION 13:

A 802.1Q tag is a marker inserted between the source and destination MAC addressesfields of the Ethernet frame.

A. TRUEB. FALSE

Answer: BQUESTION 14:

Which of the following protocol filter/s is/are predefined in ExtremeWare?

A. OSPFB. TCPC. NETBIOSD. All of these

Answer: C

QUESTION 15:

What CLI command is used to disable learning of incoming RIP routes on an interface?

A. disable rip learning B. configure rip rxmode none

8/13/2019 EW0-200

6/60

EW0-200


C. configure rip interface passiveD. None of these

Answer: B

QUESTION 16: Which statement is true? In a PC, the configured default gateway:

A. Is always within the PC IP (sub) network.B. Is always outside the PC IP (sub) network.C. Is always behind a router.D. Can be anywhere.

Answer: A

QUESTION 17: This type of OSPF router has its router interfaces connected into multiple OSPF areas.

A. ASBR.B. ABR.C. DR.D. BDR.

Answer: B

QUESTION 18:

Which CLI command would you use to configure the switch to ignore STP for selectedVLANs?

A. enable ignore-stp vlan B. enable ignore-bpdu stpd vlan C. enable ignore-bpdu stpd D. enable ignore-stp vlan

Answer: D

QUESTION 19:

Which of the following CLI commands would you use to enable ECMP for RIP?

A. enable rip route sharingB. enable route sharing ripC. enable iproute sharing

8/13/2019 EW0-200

7/60

EW0-200


D. None of these, ecmp is not supported by RIP

Answer: D

QUESTION 20:

If you wish to silently drop all traffic destined for IP network 100.219.10.0/24 with agateway of 10.219.10.1/24 and without receiving any ICMP messages that wouldotherwise be generated, which CLI command would you execute?

A. configure iproute delete 100.219.10.0/24 gateway 10.219.10.1B. configure iproute default 100.219.10.0/24C. configure iproute add blackhole 100.219.10.0/24 gateway 10.219.10.1D. configure iproute add blackhole 100.219.10.0/24

Answer: D

QUESTION 21:

What is true when VLAN corporate shows a protocol field with the value of NONE.

A. VLAN corporate will not forward any traffic.B. VLAN corporate must be a MAC-based VLAN.C. It is not possible for a VLAN to have NONE listed as the protocol.D. None of these.

Answer: A

QUESTION 22:

RIP is a routing protocol that scales to a limit. What is the maximum number ofsupported hop counts?

A. 10B. 15C. 20D. 30

Answer: B

QUESTION 23:

In order to span multiple VLANs across Extreme switches, the protocol EDP must beenabled.

A. TRUE

8/13/2019 EW0-200

8/60

8/13/2019 EW0-200

9/60

EW0-200


C. 15D. None of these

Answer: C

QUESTION 28: Which CLI command would you use to add a VLAN to a newly created STPD s1?

A. config stpd s1 add vlan B. config s1 stpd add vlan C. config stpd add s1 vlan D. config s1 add stpd vlan

Answer: A

QUESTION 29: CORRECT TEXTExhibit:

Which command provides the information displayed in the exhibit?

Answer: SHOWVLAN

QUESTION 30:

What is the default value for the RIP garbage-time setting?

A. 30 secondsB. 60 secondsC. 120 secondsD. 240 seconds

Answer: C

QUESTION 31:

In an Ethernet LAN, Layer 2 broadcasts reach every device within the same broadcastdomain and may cause bandwidth, congestion and delay issues.

8/13/2019 EW0-200

10/60

EW0-200


A. TRUEB. FALSE

Answer: A

QUESTION 32:

In order to set the OSPF router ID to 192.168.0.1 in area 7.7.7.7 which of the followingCLI commands should be used?

A. config routerid ospf 192.168.0.1 area 7.7.7.7B. config ospf routerid 192.168.0.1C. config ospf 192.168.0.1 routerid area 7.7.7.7D. config 192.168.0.1 ospf routerid


When a port is added to a tagged VLAN, jumbo frame support must be enabled tocompensate for the increased frame size.

A. TRUEB. FALSE

Answer: B

QUESTION 34:

The modular BlackDiamond 6804 switch supports the following legacy WAN modules?(Choose all three that apply)

A. 2-port SONET/SDH OC-12c/STM-4 PoSB. 4-port SONET/SDH OC-3c/STM-1 PoSC. 4-port SONET/SDH OC-3/STM-1 ATMD. 16-port SONET/SDH T3/E3 PoS/ATM

Answer: A,B,C

QUESTION 35:

In an Extreme Switch, the routing function is disabled on all VLANs by default.

A. TRUEB. FALSE

8/13/2019 EW0-200

11/60

EW0-200


Answer: A

QUESTION 36:

The acronym TCP/IP stands for:A. Transport Control Protocol/Internal ProtocolB. Transmission Control Protocol/ International ProtocolC. Transfer Control Policy/Interactive ProtocolD. None of these

Answer: D

QUESTION 37:

In a Summit 5i switch, a MAC address must be configured for each physical port beforerouting can be configured.

A. TRUEB. FALSE

Answer: B

QUESTION 38:

Given the following diagram, how would you disable ports 3 through 8 on module 1 and

all ports on modules 3 and 4?Exhibit: 1-38.gif

A. disable ports slot 1 ports 3-8, slot 3 ports 1-8, slot 4, ports 1-8B. unconfig ports 1:3-1:8, 3:1-4:8C. config vlan delete ports 1:3-1:8, 3:1-4:8D. disable ports 1:3-1:8, 3:1-4:8

Answer: D

QUESTION 39:

What information is not provided by the CLI command: show version?

A. The ExtremeWare software image version and the build date and timeB. The MAC address of the switchC. The Switch Serial NumberD. The BootROM version

8/13/2019 EW0-200

12/60

8/13/2019 EW0-200

13/60

EW0-200


QUESTION 42:

The IP ROUTING field indicates whether IP forwarding has been enabled or disabledwhen the CLI command: show ipconfig is entered.

A. TRUEB. FALSE

Answer: A

QUESTION 43:

How can you tell by looking at the front panel of an Summit 1i switch, which ports aredisabled?

A. Flashing amber lightB. Flashing green lightC. Solid amber lightD. Solid green light

Answer: B

QUESTION 44:

What does the TFTP acronym stands for?

A. True File Transfer ProtocolB. Total File Transfer ProtocolC. Trivial File Transfer ProtocolD. Transport File Trough Protocol

Answer: C

QUESTION 45:

SNMP access to a Summit 48si switch can be limited by the following methods:

A. Use an access listB. Use an access profileC. Use the CLI command: disable snmp accessD. All of these

Answer: D

8/13/2019 EW0-200

14/60

EW0-200


QUESTION 46:

In addition to maintaining an internal log, ExtremeWare supports remote logging featurevia the UNIX syslog facility.

A. TRUEB. FALSE

Answer: A

QUESTION 47:

Passwords for login names on ExtremeWare CLI accounts are case-sensitive.

A. TRUEB. FALSE

Answer: A

QUESTION 48:

Extreme switches learn source MAC addresses and perform bridging based on thedestination MAC address of incoming Ethernet frames.

A. TRUEB. FALSE

Answer: AQUESTION 49:

The RFC 1918 describes the use and benefits of IP address space for private networks.The following IP address 10.10.60.254/23 can be considered as a valid private IPaddress.

A. TRUEB. FALSE

Answer: A

QUESTION 50:

The Spanning Tree Protocol is designed to:

A. Calculate the shortest path route to a destination network.B. Calculate the topology of a network for the RIP protocol.

8/13/2019 EW0-200

15/60

8/13/2019 EW0-200

16/60

EW0-200


C. Tab keyD. None of these

Answer: C

QUESTION 55: There can be only one frame transmitted at a time on a traditional CSMA-CD Ethernetnetwork. What is the result when more frames are sent at the same time?

A. RuntsB. JabbersC. CollisionsD. Jumbo frames

Answer: C

QUESTION 56:

It is highly recommended to change the SNMP community strings on an Extreme switchfrom the factory default. The following well-known community strings apply by default:

A. R/O extreme R/W networksB. R/O public R/W privateC. R/O shared R/W secretD. R/O nonblocking R/W wirespeed


In normal IP unicast routing, all forwarding decisions are based on the ______________of each packet.

A. destination MAC addressB. source IP addressC. source MAC addressD. destination IP address

Answer: D

QUESTION 58:

I/O modules for the BlackDiamond 6808 and Alpine 3804 switch products areinterchangeable.

8/13/2019 EW0-200

17/60

8/13/2019 EW0-200

18/60

EW0-200


Given the diagram in the exhibit, which command would you use to send the switchactive configuration file to the TFTP server?

A. download config 192.168.0.1 B. upload config 192.168.0.254

C. download config 192.168.0.254 D. upload config 192.168.0.1

Answer: B

QUESTION 63:

What is the default STP max age value?

A. 20 secondsB. 30 seconds

C. 40 secondsD. 60 seconds

Answer: A

QUESTION 64:

Which CLI command would you use to configure VLAN corporate with IP address192.168.0.1/16?

A. config vlan corporate ipaddress 192.168.0.1/16

B. config ipaddress corporate vlan 192.168.0.1/16C. config ipaddress 192.168.0.1/16 vlan corporateD. config ipaddress 192.168.0.1/16 corporate vlan

Answer: A

QUESTION 65:

Upgrading the BootROM on a Summit 48i switch is done via the CLI command:

A. upload bootrom [ | ] B. enable bootrom [ | ] C. download bootrom [ | ] D. None of these

Answer: C

QUESTION 66:

8/13/2019 EW0-200

19/60

EW0-200


Classless routing and VLSM are supported by ExtremeWare.

A. TRUEB. FALSE


What is the broadcast address for 192.168.1.49/30?

A. 192.168.1.51B. 192.168.1.255C. 192.168.1.52D. 192.168.1.48


What is the maximum number of VLANs that can be tagged on a single link betweenExtreme Networks switches.

A. 1000B. 2000C. 4095D. 6000

Answer: C

QUESTION 69:

Which of the following sequences identifies a TCP three-way handshake?

A. SYN SYN ACKB. SYN ACK ACK TCP SYNC. TCP SYN ACK - SYN-ACKD. TCP SYN SYN ACK - ACK

Answer: D

QUESTION 70:

CORRECT TEXT Name one of the two user authentication protocols supported by ExtremeWare.

8/13/2019 EW0-200

20/60

EW0-200


Answer: TACACS+

QUESTION 71:

OSPF is a link-state type of routing protocol.A. TRUEB. FALSE

Answer: A

QUESTION 72:

Exhibit:

Which CLI command would have caused the output displayed in the exhibit if executed?

A. config ports 9-12 auto off duplex full speed 1000B. disable ports 9-12 autoC. config ports 9:12 auto off duplex full speed 1000D. disable ports 9:12 auto

Answer: A

QUESTION 73:

CORRECT TEXTAn Alpine 3802 switch maintains a maximum of _________ messages in its internal log?

Answer: 1000

QUESTION 74:

On an Extreme Summit 7i switch the following traffic is handled by the CPU.

A. ICMP redirectsB. PingC. Traffic destined for unknown MAC destinationsD. All of the above

Answer: D

QUESTION 75:

8/13/2019 EW0-200

21/60

EW0-200


Which one of the following can populate an IP Route Table with its route entry on anExtreme switch?

A. UDP-forwardingB. Proxy ARP

C. MAC AddressesD. None of these.

Answer: D

QUESTION 76:

Which statement is true?

A. When a bridge is root-bridge all its ports are root ports.B. When a bridge is root-bridge only one of its ports is root port.

C. When a bridge is root-bridge none of its ports is root port.D. None of the above

Answer: C

QUESTION 77:

In RIP, poison reverse processing means that:

A. A route is not advertised to the interface from which it was learned.B. A route is advertised as unreachable to the interface from which it was learned.

C. Traffic whose source interface does not match the routing table is black holed.D. None of these.

Answer: B

QUESTION 78:

Exhibit:

What can possibly cause the error displayed in the exhibit?

A. An attempt was made to add a port to a port-based VLAN, where that port was alreadyin use by another port-based VLAN.B. An attempt was made to add an IP address to port 1 when it was already configuredwith a protocol filter.C. An attempt was made to create another tagged VLAN for port 1.D. All of the above.

Answer: A

8/13/2019 EW0-200

22/60

EW0-200


QUESTION 79:

The CLI command: ?7KH&/,FRPPDQGshow s0?and the CLI command?"DQGWKH&/,FRPPDQGshow stpd s0?will display the same result.

A. TRUEB. FALSE

Answer: A

QUESTION 80:

When using IEEE 802.1D Spanning Tree Protocol, ExtremeWare supports VLANs indifferent STP Domains to share the same port when tagged.

A. TRUEB. FALSE

Answer: B

QUESTION 81:

STPDs s0, s1, and s2 have been created. What is the CLI command to enable spanningtree protocol for only s1?

A. enable stpd s1

B. enable s1 stpdC. enable dot1d s1D. None of these.

Answer: A

QUESTION 82:

What information is described by the IEEE 802.2 standard?

A. Token-ringB. ATMC. FDDID. Logical Link Control

Answer: D

QUESTION 83:

8/13/2019 EW0-200

23/60

EW0-200


Which of the following is a predefined protocol filter on an Extreme switch?

A. TELNETB. SMTPC. APPLETALK

D. None of theseAnswer: C

QUESTION 84:

An OSPF router type whose interfaces connect to two or more Autonomous Systems iscalled:

A. BDRB. ABR

C. Internal RouterD. None of these

Answer: D

QUESTION 85:

Which of the following CLI command line statements will configure an IP address on thedefault VLAN?

A. config vlan default xnetid 192.168.1.1 255.255.255.0

B. config default ipaddress 192.168.1.1/24C. enable vlan default ipaddress 192.168.1.1 255.255.255.0D. enable vlan default xnetid 192.168.1.1/24

Answer: B

QUESTION 86:

Which of the following can generate route entries for the IP route table to become populated?

A. UDP-forwardingB. proxy ARPC. RIPD. None of these.

Answer: C

8/13/2019 EW0-200

24/60

EW0-200


QUESTION 87:

Which CLI command would you use to create a static route to the 10.0.0.0/8 networkwith a gateway of 192.168.0.1/24 and a metric of 2?

A. config iproute add 10.0.0.0/8 192.168.0.1 2B. config iproute add 192.168.0.1 10.0.0.0/8 2C. create iproute add 10.0.0.0/8 192.168.0.1 2D. create iproute add 192.168.0.1 10.0.0.0/8 2

Answer: A

QUESTION 88:

CORRECT TEXTThe switch is capable of making packet-forwarding decisions by checking the FDB, and

IPFDB tables. If the switch does not find a match for the destination, the packet is queuedto the ____________ for route processing. Your answer >

Answer: CPU

QUESTION 89:

How many bits are reserved for the 802.1p priority in an 802.1p+Q tag

A. 3B. 8

C. 12D. 16

Answer: A

QUESTION 90:

Using RIP, how can you clear the IP routing table on a switch?

A. Clear iprouteB. Clear iparpC. Disable RIP / Enable RIPD. Clear ipfdb

Answer: C

QUESTION 91:

ExtremeWare automatically compensates for the increase in frame size when enabling

8/13/2019 EW0-200

25/60

EW0-200


vMAN tagging.

A. TRUEB. FALSE


What command would you execute to create a new protocol filter?

A. Enter the CLI command config protocol vlan .B. Enter the CLI command create protocol vlan .C. Enter the CLI command create protocol .D. Enter the CLI command config protocol .

Answer: CQUESTION 93:

In an Extreme Switch, a VLAN configured for routing can support only one physicalEthernet port.

A. TRUEB. FALSE

Answer: B

QUESTION 94:

Which parameter do you change on a switch to increase the probability that it becomesthe root bridge in STP.

A. Increase the Cost valueB. Decrease the Cost valueC. Increase the Priority valueD. Decrease the Priority value

Answer: D

QUESTION 95:

Exhibit:

8/13/2019 EW0-200

26/60

EW0-200


Which CLI command would provide the following information for the default VLANonly?

A. show vlanB. show vlan detailC. show vlan defaultD. All of these.

Answer: C

QUESTION 96:

When the CLI command: show stpd, shows that the switch root bridge and bridge ID arethe same, the switch is:

A. Not participating in spanning tree.B. Designated bridge.C. The root bridge.D. None of these.

Answer: C

QUESTION 97:

What load sharing algorithms are supported on switches with the ?chip-set.

A. port-basedB. address-basedC. round-robinD. all of the above.

Answer: D

QUESTION 98:

CORRECT TEXTA device management software, that allows you to access an Extreme Switch over aTCP/IP network using a standard Web browser supporting frames is called ExtremeWare ____________.

8/13/2019 EW0-200

27/60

EW0-200


Answer: VISTA

QUESTION 99:

Which CLI command would you use to create a blackhole route that blocks traffic to the10.0.0.0/8 network?

A. config iproute add 10.0.0.0/8 blackholeB. config blackhole iproute ad 10.0.0.0/8C. config iproute add blackhole 10.0.0.0/8D. None of these.

Answer: C

QUESTION 100:

What is the well-known name for port 80?

A. POP3B. TelnetC. HTTPD. FTP

Answer: C

QUESTION 101:

The CLI command to prevent VLAN corporate from forwarding broadcast traffic for ports 2:2-2:6 is: config vlan corporate add ports 2:2-2:6 nobroadcast.

A. TRUEB. FALSE

Answer: A

QUESTION 102:

ExtremeWare does not allow any configuration changes for the relative route priorityvalues.

A. TRUEB. FALSE

Answer: B

8/13/2019 EW0-200

28/60

EW0-200


QUESTION 103:

The modular Alpine switches support the following legacy WAN modules: (Choose allthree that apply)

A. 4-port T1 (RJ-48) WAN ModuleB. 4-port E1(RJ-48) WAN ModuleC. 1-port T3 (BNC) WAN ModuleD. 4-port OC12/STM4 WAN Module

Answer: A,B,C

QUESTION 104:

The IP forwarding function and routing protocols on an Extreme switch are disabled bydefault.

A. TRUEB. FALSE

Answer: A

QUESTION 105:

Extreme Networks switches that use the ?chipset support switching and routing of jumboframes at wire-speed on all ports.

A. TRUEB. FALSE

Answer: A

QUESTION 106:

What information can you find using the CLI command show edp?

A. ExtremeWare code version used by remote switch.B. The ports that are disabled on the remote switch.C. The master port of any load share groups.D. The speed and duplex settings of the ports connecting the two switches.

Answer: A

QUESTION 107:

Autonegotiation is enabled by default on all Ethernet ports of an Extreme switch.

8/13/2019 EW0-200

29/60

EW0-200


A. TRUEB. FALSE

Answer: A

QUESTION 108:

When multiple VLANs need to be configured on one physical port, all these VLANsmust be configured with a tag.

A. TRUEB. FALSE

Answer: B

QUESTION 109: The following applies when you execute a scheduled incremental download from a TFTPserver.

A. There must be IP connectivity between the switch and the TFTP server.B. The TFTP server must have the correct configuration in the right placeC. The configuration will not automatically be saved unless you specify this in the file.D. All of the above

Answer: D

QUESTION 110:

Which of the following methods can be used to access an Extreme Networks switch?

A. SNMPB. RS-232C. TelnetD. HTTPE. All of the above

Answer: E

QUESTION 111:

How could you verify that MAC address learning is disabled for ports 1 to 8 on aSummit7i switch?

A. Enter the CLI command: show ports 1,8 config detail

8/13/2019 EW0-200

30/60

EW0-200


B. Enter the CLI command: show ports 1-8 management detailC. Enter the CLI command: show ports 1,8 statistics detailD. Enter the CLI command: show ports 1-8 info detail

Answer: D

QUESTION 112:

Which CLI command would enable you to schedule a configuration upload to occur atregular intervals?

A. upload config every B. upload config C. upload config D. upload config every


The following console speeds are supported when a switch runs in bootROM mode.(Choose the two that apply)

A. 2400 bpsB. 9600 bpsC. 38400 bpsD. 115200 bps

Answer: B,C

QUESTION 114:

What command will provide you with information on SNMP statistics and SNMP accessattempts?

A. Show snmpB. Show switchC. Show epicenterD. Show management

Answer: D

QUESTION 115:

When you type in the history command, the switch will show you the previous 49commands. Using the arrow up/down key you can retrieve such a command.

8/13/2019 EW0-200

31/60

8/13/2019 EW0-200

32/60

EW0-200


QUESTION 120:

What is the default IP RIP route advertisement timer value?

A. 30 seconds

B. 60 secondsC. 120 secondsD. 180 seconds

Answer: A

QUESTION 121:

Which CLI command will configure VLAN corporate to use the protocol filter netbios:

A. config vlan corporate add protocol netbios

B. config vlan corporate protocol netbiosC. config vlan corporate add netbiosD. None of these

Answer: B

QUESTION 122:

The CLI command: configure vlan corporate ipaddress 10.10.101.0/24 is a validcommand.

A. TRUEB. FALSE

Answer: B

QUESTION 123:

The RFC 1918 describes the use and benefits of IP address space for private Internets.The following IP address 192.168.260.1/24 can be considered as a valid private IPaddress.

A. TRUEB. FALSE

Answer: B

QUESTION 124:

What is the CLI command to configure a VLAN to only allow IPX-related traffic?

8/13/2019 EW0-200

33/60

EW0-200


A. config protocol ipxB. config protocol ipxC. config ipx protocol D. None of these.

Answer: A

QUESTION 125:

Exhibit:

Given the diagram displayed in the exhibit, which command would you use to send aswitch configuration file from the TFTP server to the switch?

A. download config 192.168.0.254 B. download config 192.168.0.1 C. upload config 192.168.0.254 D. upload config 192.168.0.1

Answer: A

QUESTION 126:

The Extreme switch ASIC look-up Host Table containing IP host routes, outboundVLAN interfaces and ports is called:

A. IP Route TableB. IP ARP TableC. IP FDB

Answer: C

QUESTION 127:

In addition to maintaining an internal log, the switch supports remote logging by way ofthe UNIX syslog host facility. What would you do to enable remote logging on anExtreme switch?

A. Configure the syslog host to accept and log messagesB. Enable remote logging on the switch using the CLI command: enable syslog

8/13/2019 EW0-200

34/60

EW0-200


C. Configure remote logging using the CLI command: config syslog add D. All of these

Answer: D

QUESTION 128: There are no collisions occurring on a stable full duplex Fast Ethernet connection.

A. TRUEB. FALSE

Answer: A

QUESTION 129:

If you want to clear all the log entries, you have to type the following CLI command:A. clear logB. clear log allC. Clear log staticD. Clear log permanent

Answer: C

QUESTION 130:

CORRECT TEXTAn Ethernet broadcast domain is equivalent to a created ___________ within the switch.

Answer: VLAN

QUESTION 131:

CORRECT TEXTThe _______________ CLI command is used to view Spanning Tree Protocolconfiguration settings of domain S1 only. Your answer >

Answer: SHOWS1

QUESTION 132:

The ExtremeWare feature VLAN aggregation allows multiple sub-VLANs to share asingle IP subnet.

A. TRUE

8/13/2019 EW0-200

35/60

8/13/2019 EW0-200

36/60

EW0-200


QUESTION 137:

Broadcast frames are the only type of frames that may flood across VLANs.

A. TRUE

B. FALSEAnswer: B

QUESTION 138:

How many steps (packets) does it take to close a TCP session?

A. 2B. 3C. 4

D. 5Answer: C

QUESTION 139:

What is the default area type for all OSPF areas created using the ExtremeWare CLI:create ospf area ?

A. StubB. NSSA

C. NormalD. None of these

Answer: C

QUESTION 140:

Per Extreme switch port the maximum number of 802.1D spanning tree protocol domainsis:

A. 32B. 64C. 128D. None of these

Answer: D

QUESTION 141:

8/13/2019 EW0-200

37/60

EW0-200


Which routing solution in IP RIP prevents loop problems by sending a hop count of 16?

A. split horizonB. poison reverseC. ECMP

D. triggered updatesAnswer: B

QUESTION 142:

In ExtremeWare user account names and VLAN names share the same name space.Therefore a user named efault?cannot be created.

A. TRUEB. FALSE

Answer: A

QUESTION 143:

The CLI command to create a new user account named Bill with no password is: createaccount user Bill password none.

A. TRUEB. FALSE


in 802.1D mode ExtremeWare supports a VLAN being a member of up to 128 STPdomains.

A. TRUEB. FALSE

Answer: B

QUESTION 145:

What is the maximum specified distance for Extreme LX-100 fiber optic GBIC?

A. 550 metersB. 10 kilometerC. 70 kilometer

8/13/2019 EW0-200

38/60

EW0-200


D. 100 kilometer

Answer: D

QUESTION 146:

What is the purpose of the Spanning Tree Protocol listening state?

A. Listening to BPDUs to ensure there are no loops in the network.B. Building a forwarding database.C. Learning Mac addresses.D. Building a filter table.

Answer: A

QUESTION 147:

You need to add 192.168.0.254 as a trap receiver with a community of SECRET on anExtreme switch. How will you do this?

A. config snmp 192.168.0.254 trapreceiver add community secretB. config snmp add 192.168.0.254 trapreceiver community SECRETC. config snmp trapreceiver 192.168.0.254 add community secretD. config snmp add trapreceiver 192.168.0.254 community SECRET

Answer: D

QUESTION 148:

A newly-created VLAN has no member ports, is untagged, and uses protocol filterny?until one configures it otherwise.

A. TRUEB. FALSE

Answer: A

QUESTION 149:

What type of an OSPF area is used to limit the distribution of external routes?

A. Stub areaB. Normal areaC. Backbone areaD. None of these

8/13/2019 EW0-200

39/60

EW0-200


Answer: A

QUESTION 150:

You can only use the RMON features on the Extreme switch if you have an RMONmanagement application, and have enabled RMON on the switch.

A. TRUEB. FALSE

Answer: A

QUESTION 151:

In an Extreme switch, all ports are enabled by default. If a port is disabled however, the

link will also be disabled.A. TRUEB. FALSE

Answer: B

QUESTION 152:

A Summit 5i switch is able to store up to two separate configuration files in the locationscalled IMAGE1 and IMAGE2.

A. TRUEB. FALSE

Answer: B

QUESTION 153:

Which CLI command will list the ports involved in load sharing and also identifies themaster logical port?

A. show ports all statB. show ports all utilizationC. show ports all configurationD. All of these

Answer: C

8/13/2019 EW0-200

40/60

EW0-200


QUESTION 154:

Split Horizon and Poison Reverse are both enabled by default on an Extreme Switch afterenabling RIP routing.

A. TRUEB. FALSE

Answer: A

QUESTION 155:

The CLI command to disable poison reverse on an Extreme switch is:

A. disable rip poisonreverse noadvertiseB. disable poisonreverse rip noadvertise

C. disable rip poisonreverseD. disable poisonreverse rip

Answer: C

QUESTION 156:

UDP, like TCP runs on top of IP networks but what differs UDP from TCP?

A. UDP is a connectionless protocolB. UDP provides few error recovery services

C. With UDP datagram delivery is not guaranteedD. all of the above

Answer: D

QUESTION 157:

What industry specification defines the ability to associate multiple VLANs on a singleEthernet link and is supported on Extreme Networks switches?

A. MPLSB. 802.1QC. ISLD. Answer b & c

Answer: B

QUESTION 158:

8/13/2019 EW0-200

41/60

EW0-200


Which is the proper net mask for a class b network with a subnet of 6 bits?

A. 255.255.0.0B. 255.240.0.0C. 255.255.252.0

D. 255.255.255.0Answer: C

QUESTION 159:

If an asterisk (*) appears in front of the ExtremeWare command-line prompt, what does itindicate?

A. A CLI how?command was executedB. A CLI ave?command was executed

C. Nothing, because the asterisk is always present anywayD. None of these

Answer: D

QUESTION 160:

How would you stop a scheduled configuration upload from happening? Use the CLIcommand:

A. cancel configuration upload

B. configuration upload cancelC. delete configuration uploadD. upload configuration cancel

Answer: D

QUESTION 161:

Which of the following does not create entries in the routing table?

A. ARPB. RIPC. OSPFD. Static routes

Answer: A

QUESTION 162:

8/13/2019 EW0-200

42/60

EW0-200


Link aggregation is supported on a Summit 1i and the following load sharing algorithm isrecommended by Extreme Networks.

A. port-basedB. address-based

C. round-robinD. None of the above, link aggregation is not supported

Answer: B

QUESTION 163:

Which of the ExtremeWare features will allow you to increase bandwidth and resiliency by using a group of ports to carry traffic in parallel between two switches?

A. ESRP

B. VLAN AggregationC. QoSD. None of these

Answer: D

QUESTION 164:

What is the result of enabling spanning tree in a network?

A. Selects the best path between LAN for redundancy.

B. Reduces the number of broadcasts necessary by forwarding a specific subnet.C. Creates a loop-free layer-2 topology.D. Defined by IEEE 802.1D to enforce a hybrid ring network topology.

Answer: C

QUESTION 165:

When changing the password for John Doe management account, using the CLIcommand: config account johndoe password , you will be asked to enter the password twice.

A. TRUEB. FALSE

Answer: A

QUESTION 166:

8/13/2019 EW0-200

43/60

EW0-200


When a host, using TCP/IP, communicates with a destination outside its VLAN it relieson the configured default gateway. What is the destination MAC address in an Ethernetframe sent by this host destined to another VLAN? The ARP request has already beenreplied.

A. The MAC address of the destinationB. The MAC address of the default gatewayC. The MAC address of the sourceD. The general broadcast address.

Answer: B

QUESTION 167:

Which CLI commands would you use to configure VLAN CORPORATE (tag 100) with ports 1:1 through 4:8 tagged and ports 5:1 through 8:8 as untagged?

A. config vlan corporate ports add 1:1-4:8 taggedconfig vlan corporate ports add 5:1-8:8 untaggedB. config vlan corporate add ports 1:1-4:8 taggedconfig vlan corporate add ports 5:1-8:8 untaggedC. config corporate vlan add ports 1:1-4-8 taggedconfig corporate vlan add ports 5:1-8:8 untaggedD. config corporate vlan ports add 1:1-4:8 taggedconfig corporate vlan ports add 5:1:8:8 untagged

Answer: B

QUESTION 168:

Which CLI command would enable you to schedule a configuration download to occur atregular intervals?

A. download config B. download config C. download config every D. download config every

Answer: D

QUESTION 169:

What is the maximum number of FDB entries in a Summit 7i?

A. 256000B. 128000

8/13/2019 EW0-200

44/60

EW0-200


C. 64000D. 32000

Answer: A

QUESTION 170: CORRECT TEXTWhat CLI command will accomplish the selection of the secondary software image thenext time the switch is rebooted?

Answer: USEIMAGESECONDARY

QUESTION 171:

How would you create a VLAN named corporate using the CLI command?

A. create vlan corporateB. config vlan corporateC. enable vlan corporateD. None of these.

Answer: A

QUESTION 172:

How many unique physically MAC addresses has a Summit 48i switch?

A. 1B. 64C. Depends on the number of Ethernet ports.D. 4096

Answer: A

QUESTION 173:

CORRECT TEXTYou have used the CLI command: config syslog add 192.168.1.1 local0 info, to set upyour syslog server. You later check the syslog server and see that no messages have beenrecorded. What CLI command should you have entered next?

Answer: ENABLESYSLOG

QUESTION 174:

8/13/2019 EW0-200

45/60

8/13/2019 EW0-200

46/60

EW0-200


A. Triggered updatesB. Poison ReverseC. Split HorizonD. All of these

Answer: DQUESTION 179:

The acronym UDP stands for:

A. Unreliable Delivery ProtocolB. User Datagram ProtocolC. Unspecified Data ProfileD. None of these


In CSMA/CD, where does CS stand for?

A. Common senseB. Collision senseC. Carrier senseD. Closed subnet

Answer: CQUESTION 181:

ExtremeWare can automatically upload the active configuration to an FTP server.

A. TRUEB. FALSE

Answer: B

QUESTION 182:

A Summit 7i switch can support up to __________ active Telnet sessions concurrently.

A. 5B. 6C. 7D. 8

8/13/2019 EW0-200

47/60

EW0-200


Answer: D

QUESTION 183:

Which of the following routes will be used to forward a frame to 192.168.1.174?A. 192.168.1.0/29B. 192.168.1.128/30C. 192.168.1.128/25D. None of these.

Answer: C

QUESTION 184:

The Rip hold timer to remain a route in the routing table without receiving updates is?A. 60 seconds, 2 times the update timerB. 120 seconds, 4 times the update timerC. 180 seconds, 6 times the update timerD. 240 seconds, 8 times the update timer

Answer: C

QUESTION 185:

The maximum number of OSPF virtual links that an Extreme Summit1i switch cansupport is 32.

A. TRUEB. FALSE

Answer: A

QUESTION 186:

What will this CLI command accomplish: config vlan accounting protocol Appletalk?

A. It assigns Appletalk as one of the predefined protocols for use by the accountingVLANB. It configures the VLAN accounting as a protocol-based VLAN and will filter out all protocols except AppleTalkC. It adds a new predefined protocol vlan called AppletalkD. None of these

8/13/2019 EW0-200

48/60

EW0-200


Answer: B

QUESTION 187:

What is one of the functions of the ISO/OSI data-link layer?A. Encoding and decoding of signalsB. Provide one or more service access points.C. Manage communication over the linkD. None of the above

Answer: C

QUESTION 188:

TCP's method of flow control is called sliding window.A. TRUEB. FALSE

Answer: A

QUESTION 189:

When enabling load sharing in an Extreme switch, only a single switch must beconfigured. The switches will auto-negotiate the port sharing settings via the EDP

protocol.A. TRUEB. FALSE

Answer: B

QUESTION 190:

ExtremeWare provides two release strategies, General Deployment and GeneralAvailability. The first is a stable release strategy with successive versions including bugfixes. The GA release is to introduce new features and products that will convert to GDstatus.

A. TRUEB. FALSE

Answer: A

8/13/2019 EW0-200

49/60

EW0-200


QUESTION 191:

How long in seconds, is the Extreme switch?FDB Aging time set at by default?

A. 100

B. 200C. 300D. 400

Answer: C

QUESTION 192:

IP Forwarding is enabled by default only on the pre-configured VLAN DEFAULT.

A. TRUE

B. FALSEAnswer: B

QUESTION 193:

Which of the following is a predefined protocol filter in an Extreme Switch?

A. IPB. IPXC. Appletalk

D. all of the aboveAnswer: D

QUESTION 194:

A Bridge divides a network into:

A. IP-subnetsB. Collision domainsC. Broadcast domainsD. None of the above

Answer: B

QUESTION 195:

CORRECT TEXTWhat CLI command is used to show the port membership of only VLAN default?

8/13/2019 EW0-200

50/60

8/13/2019 EW0-200

51/60

EW0-200


QUESTION 200:

The modular BlackDiamond 6816 switch offers how many slots?

A. 4 I/O module slots and 2 MSM slots

B. 8 I/O module slots and 2 MSM slotsC. 16 I/O module slots and 2 MSM slotsD. 16 I/O module slots and 4 MSM slots

Answer: D

QUESTION 201:

What happens when one executes the CLI command: unconfigure switch all?

A. Resets configuration to factory defaults without a reboot

B. Erases the entire current configuration without a rebootC. Erases the configuration selected for next reboot, resets to factory defaults and rebootsthe switchD. Erases both configurations and reboots the switch

Answer: C

QUESTION 202:

The IEEE specification standard for the Spanning Tree Protocol is the:

A. IEEE 802.1DB. IEEE 802.1ADC. IEEE 802.1PD. IEEE 802.1Q

Answer: A

QUESTION 203:

ExtremeWare supports two levels of management ?user and administrator. When loggedin as a user, one has viewing access to all manageable parameters including User accountdatabase and SNMP community strings.

A. TRUEB. FALSE

Answer: B

8/13/2019 EW0-200

52/60

EW0-200


QUESTION 204:

Which CLI command would you use to configure VLAN corporate with a tag value of100?

A. config vlan corporate create tag 100B. config vlan corporate tag 100C. config vlan corporate add 100 tag

Answer: B

QUESTION 205:

What is the default 802.1Q Tag Protocol ID used by Extreme Networks switches?

A. 0x8000

B. 0x8100C. 0x9000D. 0x9100

Answer: B

QUESTION 206:

The default setting for spanning tree on an Extreme Networks switch is?

A. Off for the entire switch.

B. Off for the entire switch, with the exception of VLAN Default.C. On for the entire switch.D. On for the entire switch, with the exception of VLAN Default.

Answer: A

QUESTION 207:

What is a CP SYN?request?

A. A request from a TCP client to synchronize an FTP sessionB. A request from a TCP station to establish a TCP session to another stationC. A request from a TCP server to re-send telnet dataD. TCP client to server keep-alive

Answer: B

QUESTION 208:

8/13/2019 EW0-200

53/60

EW0-200


You need to change the name of a VLAN from corporate to corp. What steps would youtake to do this?

A. config name corporate corpB. config corporate name corp

C. config name corp corporateD. config corp name corporate

Answer: B

QUESTION 209:

Which CLI command should be used to configure the link cost for RIP?

A. config rip link-costB. config rip link-metric

C. config rip metric-tableD. None of these

Answer: D

QUESTION 210:

An Ethernet port cannot be added to two VLANs as an untagged port, with the followingexception:

A. Neither VLAN has a configured 802.1Q tag.

B. Both VLANs are configured for differing protocol types.C. 802.1Q negotiation is enabled on both VLANs.D. None of these.

Answer: B

QUESTION 211:

ICMP traffic on a Summit 1i switch is always handled in hardware at wire-speed by theASIC.

A. TRUEB. FALSE

Answer: B

QUESTION 212:

RIP supports the distribution of non-originated RIP routes using a command beginning

8/13/2019 EW0-200

54/60

EW0-200


with: enable rip export.

A. TRUEB. FALSE


This CLI command is valid: configure vlan default ipaddress 10.10.1.1/24 255.255.255.0.

A. TRUEB. FALSE

Answer: B

QUESTION 214: You are taking steps to secure SNMP access to your switches by turning off SNMPaccess to the switches. What is the minimum action you need to perform?

A. Enter the CLI Command DISABLE SNMP ACCESS and then reboot the switch.B. Enter the CLI Command DISABLE SNMP ACCESSC. Enter the CLI Command DISABLE SNMPD. Enter the CLI Command DISABLE SNMP and then reboot the switch.

Answer: B

QUESTION 215:

Which is not a tunable configuration option for STP?

A. Bridge priorityB. Hello timeC. Port CostD. Rapid cache timer

Answer: D

QUESTION 216:

What is the proper CLI command syntax to create a user-level account for johndoe?

A. create user account johndoeB. create account user johndoeC. create account johndoe user

8/13/2019 EW0-200

55/60

EW0-200


D. None of these.

Answer: B

QUESTION 217:

CORRECT TEXTThe command ______________ shows all information necessary for support by Extreme Networks?

Answer: SHOWTECH

QUESTION 218:

What information is provided by the CLI command: show version? (Choose all three thatapply)

A. The ExtremeWare software imageB. The MAC address of the switchC. The Switch Serial NumberD. The BootROM version

Answer: A,C,D

QUESTION 219:

When a bridge receives an Ethernet frame with an unknown destination MAC address,

what does it do?A. Disable the ingress Ethernet port.B. Floods the Ethernet frame to all other ports.C. Set the egress ports in forwarding mode.D. Set the egress ports in learning mode.

Answer: B

QUESTION 220:

Prior to downloading a new software image to an Extreme switch using the network, youare required to place the software image in a file on a TFTP server that is accessible onthe network.

A. TRUEB. FALSE

Answer: A

8/13/2019 EW0-200

56/60

EW0-200


QUESTION 221:

ExtremeWare does not support the exterior gateway protocol ?BGP4 in any of theExtreme Networks switch products.

A. TRUEB. FALSE

Answer: B

QUESTION 222:

Is this a valid CLI command : enable ignore-stp vlan default?

A. TRUE

B. FALSEAnswer: A

QUESTION 223:

ExtremeWare supports ECMP for which of the following routes? (Choose all that apply)

A. OSPF routesB. RIP routesC. Static routes

D. None of the aboveAnswer: A,C

QUESTION 224:

ExtremeWare provides two methods, RADIUS and TACACS+, to authenticate users whologin to the switch. However, you cannot simultaneously enable the switch for bothmethods.

A. TRUEB. FALSE

Answer: A

QUESTION 225:

Each IP address and mask configured for a VLAN must represent a unique IP subnet.However, the VLAN aggregation option allows you to use the same IP subnet on

8/13/2019 EW0-200

57/60

EW0-200


different VLANs.

A. TRUEB. FALSE


What command would you use to add a new SNMP read-write community string calledu.nt.b9?on your switch?

A. config snmp community readwrite eu.nt.b9B. config snmp add community readwrite eu.nt.b9C. create snmp readwrite community eu.nt.b9D. create snmp add readwrite community eu.nt.b9

Answer: B

QUESTION 227:

Which CLI command is used to see the active connections to the switch.

A. show sessionB. show connectionC. show userD. show account

Answer: A

QUESTION 228:

Exhibit:

What CLI command was executed and results in the system returning an error asdisplayed in the exhibit.

A. config corporate add port 1B. config vlan corporate add port 1 taggedC. config port 1 add vlan corporateD. None of these

Answer: A

8/13/2019 EW0-200

58/60

EW0-200


QUESTION 229:

What is the result when the CLI command: disable stpd port 4:1-4:8 is entered,?

A. Ports 4:1-4:8 are placed into the blocking state.

B. Ports 4:1-4:8 are placed into the listening state.C. Ports 4.1-4.8 are placed into the learning state.D. Ports 4:1-4:8 are placed into the forwarding state.

Answer: D

QUESTION 230:

What is the maximum number of IP host addresses that fit in this network172.168.128.96/27?

A. 14B. 30C. 62D. 254

Answer: B

QUESTION 231:

The OSPF Area 0.0.0.0 is always pre-configured on an Extreme switch as a ___________ area type.

A. StubB. NSSAC. NormalD. None of these

Answer: C

QUESTION 232:

In spanning tree algorithm, the switch with the ___________________ is elected as theroot bridge.

A. most number of active portsB. lowest numerical bridge IDC. highest numerical bridge IDD. None of these

Answer: B

8/13/2019 EW0-200

59/60

EW0-200


QUESTION 233:

What happens if the following CLI command is executed? create fdbentry00:E0:2B:12:34:56 vlan corporate port 4

A. Adds a temporary static entry to the FDBB. Adds a permanent static entry to the IPFDBC. Adds a permanent static entry to the IPARPD. Adds a permanent static entry to the FDB

Answer: D

QUESTION 234:

What is the well-known port number for Telnet?

A. 25B. 110C. 22D. 23

Answer: D

QUESTION 235:

In an Extreme switch, if MAC address learning is disabled on a port, no traffic destined

to a permanent MAC address matching that port number will be forwarded, not even broadcast traffic.

A. TRUEB. FALSE

Answer: B

QUESTION 236:

If you change and then forget the only remaining password for the CLI Administratoraccount ability to log on to an Extreme switch, how can you recover the passwordwithout loosing the configuration?

A. Provide dial-up, modem access to the switch console port for Extreme support to dialinB. Contact the local Extreme Systems EngineerC. You can RMA the switch and return to Extreme Corporate officesD. All of these

8/13/2019 EW0-200

60/60

EW0-200

Answer: D

QUESTION 237:

BGP, OSPF and RIP are interior gateway protocols supported by ExtremeWare.A. TRUEB. FALSE

Answer: B

QUESTION 238:

What is the meaning of the following CLI command: con ipr a bl 10.11.12.0/24?

A. Configure a blackhole route that blocks traffic destined to the 10.11.12.0/24 network.B. Configure a default route that forwards traffic destined to the 10.11.12.0/24 network.C. Configure a static route that forwards traffic destined to the 10.11.12.0/24 network.D. None of these.

Answer: A

QUESTION 239:

The default settings for the console port of an ?chipset switch are: 9600 bps/8data-bits/one stop-bit/no parity/software flow control

A. TRUEB. FALSE

Answer: A

QUESTION 240:

The Alpine series switches are provided with a passive backplane.

A. TRUEB. FALSE

Answer: B

Documents

EW0-200