, 2010

Copyright Kohler China Ltd., 2010

�

�

�

�

Please read these instructions carefully tofamiliarize yourself with the required tools, materials,and installation sequences. Follow the sections thatpertain to your particular installation. This will helpyou avoid costly mistakes. In addition to properinstallation, read all operating and safety instructions.All information is based on the latest productinformation available at the time of publication.Kohler China Ltd. reserves the right to makechanges in product characteristics, packaging, oravailability at any time without notice.These instructions contain important care, cleaning,and warranty information-

Please provide adequate available space for thebath unit in accordance with rough-in. Arrange thelocation of drain in advance.

All installations must comply with council and localauthority by-laws. It is the responsibility of the installerto ensure that the waste is made watertight by meansof silicone sealant or caulking compound.

The bath can be installed after the decoration ofthe bathroom walls is finished. However, bath drain andwater pipe shall be pre-arranged.

please leave theseinstructions for the consumer.

IMPORTANT:

NOTE:

�

�

�

�

BEFORE YOU BEGIN

A.

�

�

A. Summary Of Key Requirements

Observe all local plumbing codes.Install the unit to a level subfloor.

�

�

PRODUCT REQUIREMENTS

EVOK

INSTALLATION INSTRUCTIONS

FREESTANDING ACRYLIC BATHK-18343T/K-18347T/K-18353T

368 201419

B. Plumbing Specifications

If using a rim-mounted bath faucet, flexible connectionsbetween the valves and spout may be required.

Confirm adequate mounting, connection ofspecified faucet for your installation.

space

B.

C. Product Inspection

Uncrate and inspect bath for damage. All Kohler sbaths have been manufactured with sophisticatedcraftsmanship. However, please inspect for anypossible damage that may have occurred in transit.Leave all materials in the crate during construction toprevent damage.

'

C.

-1-1119528-T01-C

-2-

NOTE: Damage occurred during transport orinstallation shall not be covered by warranty.

SITE REQUIREMENTS

A.A. Preparation

Check the flooring under the bath, and make repairs as

needed. Make sure the is level. It is strongly

recommended to prepare waterproof layer for the

subfloor beforehand.

Subfloor

subfloor

D.D. Clearance Requirements

Check the roughing-in and room dimensions to provide

adequate available space for the bath unit.

�

�

�

�

�

�

�

�

�

�

Adjustable pipe

wrench

Rule

Level

Safety shoes

Safety glasses

Square

Screwdriver

Pliers

Utility knife

Adjustable wrench

�

�

�

�

�

�

�

Plumbers putty

Wall coverings(as necessary)

Silicone sealant

Gypsum cement(optional)

Construction adhesive

(optional)

Protective covering for

bathtub

Nails

B. Materials RequiredA. Tools Required

�

�

�

�

�

�

�

�

�

�

�

�

�

�

�

�

�

( )

( )

( )

B.A.

INSTALLATION REQUIREMENTS

D. New or Replacement Installation

Requirements

This bath can be installed in new or existing bathrooms.For replacement: Remove the old bath, and removeenough old wall material and floor covering from thearea to allow for installation. Remove any old plumbingthat does not confo m to the rough-in requirements.For new installation: Position the plumbing according tothe rough-in dimensions. Cap the suppliers, and checkfor leaks.

r

D.

C. Installation Note: C. :

Read the entire installation instructions included withfixture before beginning the installation.

If installing a rim-mounted faucet, make sure there is nointerference with drain overflow before drilling anyholes.

1119528-T01-C

-3-

INSTALL THE BATH

A. Put the bath at desired position

1. Adjust the feet under the bath to make it level. Adjustthe height of the bath to the height marked in theRoughing-In. Tighten the nut on the adjustable feetto settle the height of the bath.

The bath must be installed level on a flat and levelsubfloor without any bumps or protrusions.Adjust the height of the bath to the height marked inthe Roughing-In.

IMPORTANT:�

�

A.

1.

�

�

2. Place the base on the floor. 2.

3. Fix the base on the floor with silicone sealant. 3.

4. Apply silicone sealant around the tail end of thedrain hose. Connect the drain hose with floor drain.Make sure the drain hose protrudes from the floor fora certain length to facilitate future bath removal.

4.

BEFORE INSTALLATION

A.A. Protect the Bath UnitCover the bath with a protective layer or similarmaterial. Be careful not to scratch the bath surface.

5. Connect cold and hot supplies and check allconnections for leak.

5.

1119528-T01-C

6. Apply lubricating oil both to the inner surface of theguide bush and the outer surface of the guide pin.Insert the guide pin into the guide bush to finally fix thebath onto the floor.

6.

-4-

B. Plumbing Installation

The drain has been installed onto the bath before itleaves factory. Fill the bath with water before the bathis securely positioned so as to check the connectionsfor leaks. Damage caused by negligence is not coveredby warranty.

Be careful not to damage the bottom of the bathand the subfloor.Note:

B.

Guide Pin

Guide BushBase

1119528-T01-C

C. install theRemove and freestandingbath

If the freestanding bath needs removing, please followthe steps below:

Lift the bath levelly, then the guide pin could bepluged out of the guide bush. Then remove the nuton the drain tail pipe.

1)

C.

1)

-5-

*

* 2

Mequiars 28 ( )

( )

Cleaning and Care

Cleaning Acrylic Surfaces: Do not use abrasivecleansers on any acrylic surfaces, as they will scratchand dull the surface. Wipe out the bath after each useto prevent a build-up of soap and scum.

If the acrylic surface becomes dull, an automotive typerubbing compound may be used on the unit, followedby an application of paste wax.

We recommend:Rubbing compound mequiars mirror glaze 28 metalpolish (import product)

reen oil.

*

*

G

IMPORTANT CONSUMER INFORMATION

2) When installing the freestanding bath, please firstapply lubricating oil both to the inner surface of theguide bush and the outer surface of the guide pin,and then insert the guide into the guide bush.

2)

Nut of the Drain Tail Pipe

1119528-T01-C