Estimating the Life Expectancy of Thin Asphalt Overlays in New … · In this presentation… WhyThinOverlays? StudyGoals&Objectives ResearchApproach Construction of Sections & Instrumentation

Estimating the Life Expectancy of Thin Asphalt Overlays in New Jersey

Ayman Ali, Ph.D.Manager, Center for Research and Education in Advanced

Transportation Engineering Systems (CREATEs)Rowan University

109 Gilbreth ParkwayMullica Hill, NJ 08062Tel: (908) 283-0467

Email: [email protected]

mailto:[email protected]

Acknowledgement Dr. Hashim Rizvi Ms. Caitlin Purdy Mr. Ian Sennstrom Mr. Andrae Francoise Ms. Eileen Sheehy Ms. Susan Gresavage Mr. Paul Hanczaryk Mr. Robert Blight Dr. Giri Venkiteela Ms. Kimbrali Davis

2

In this presentation… Why Thin Overlays? Study Goals & Objectives Research Approach Construction of Sections &

Instrumentation HVS Testing Plan Preliminary Testing Results Final Remarks Questions

3

4

Why Thin Asphalt Overlays?

Why Thin Asphalt Overlays? Around 50% of NJDOT’s roads are

PCC pavements. These roads are generally in poor

condition. Thin overlays are typically used to

extend the life of these pavements. However, these overlays have been

performing poorly in the field.

5

6

Goals and Objectives

Goals Conduct accelerated full-scale

pavement testing to evaluate theperformance of thin asphalt overlaytreatments used on Portland CementConcrete (PCC) pavements.

Analyze testing results to estimatethe expected life of thin asphaltoverlays applied over PCCpavements.

7

8

Research Approach

Research Approach

9

Conduct A Comprehensive Literature Review1

Evaluate Current Condition of PCC Pavements in NJ2

Identify Major Factors Affecting Life Expectancy of Thin Asphalt Overlays3

Construct Full-Scale PCC Sections Overlaid with Thin Asphalt Overlays.4

Research Approach

10

Apply Accelerated Loading Using a Heavy Vehicle Simulator (HVS)5

Monitor Performance of Thin Asphalt Overlays as Loading Progresses6

Analyze Testing Results7

Provide NJDOT with Findings and Recommendations8

Overlays Considered

11

A 9.5 mm. NMAS Superpave Mix (Control)

12.5 mm. NMAS Stone Matrix Asphalt (SMA)

High Performance Thin Overlay (HPTO)

Binder Rich Intermediate Course (BRIC)

B

C

D

Full-Scale Pavement Sections

12

A total of six sections wereconstructed at CREATEs acceleratedpavement testing facility.

Combinations of the four overlayswith varying thicknesses.

The supporting PCC pavementstructure was similar for all sections.

Full-Scale Pavement Sections

13

The sections were instrumented using aset of sensors including: Thermocouples Soil Compression Gauges Pressure cells Asphalt Strain Gauges LVDTs

The goal was to compare fieldperformance (rutting and reflectivecracking).

Full-Scale Sections

14

Binder Rich Intermediate Course (1 inch)9.5 mm. NMAS Superpave (3 inches)

PCC Layer (8 inches)

Subbase Layer (16 inches)

Compacted Natural Soil (12 inches)

Natural Soil

Section No. 1: 9.5 mm. NMAS Superpave Control Section

Full-Scale Sections

15

12.5 mm. NMAS SMA (3 inches)




Natural Soil

Section No. 2: 12.5 mm. NMAS SMA A Specialty NJDOT Overlay mix

16

High Performance Thin Overlay (2 inches)




Natural Soil

Section No. 3: High Performance Thin Overlay A Specialty NJDOT Overlay mix

Full-Scale Sections

Full-Scale Sections

17

9.5 mm. NMAS Superpave (2 inches)Binder Rich Intermediate Course (1 inch)




Natural Soil

Section No. 4: A combination of 9.5 mm.

Superpave and Binder Rich Intermediate Course (BRIC) Mixes.

BRIC is a Specialty NJDOT Overlay mix

Full-Scale Sections

18

12.5 mm. NMAS SMA (2 inches)Binder Rich Intermediate Course (1 inch)




Natural Soil

Section No. 5: A combination of 12.5 mm.

SMA and BRIC Mixes.

Full-Scale Sections

19

High Performance Thin Overlay (1 inch)Binder Rich Intermediate Course (1 inch)




Natural Soil

Section No. 6: A combination of HPTO and

BRIC Mixes.

20

Construction of Full-Scale Sections

Construction Phase-I (Facility)

21Construction Site: Work Begins


22Construction Site: Foundations


23Construction Site: Steel Structure


24Construction Site: Fabric Cover


25Construction Site: Fabric Cover


26Construction Site: Fabric Structure (Inside)


27Construction Site: Infrastructure


28Construction Site: Completed Facility

Construction Phase-II (NJDOT Sections)

29NJDOT Sections: Marking Sections Locations


30NJDOT Sections: Milling Existing Pavement


31NJDOT Sections: Milling Existing Pavement


32NJDOT Sections: Concrete Forms


33NJDOT Sections: Concrete Placement (Slabs)


34NJDOT Sections: Final PCC Slabs


35NJDOT Sections: HMA Overlays Paving







39

Instrumentation of Sections

Goals of Instrumentation

40

Assess the impact of reflectivecracking on performance of thinasphalt overlays.

Assess the impact of joint verticalmovements on performance of thinasphalt overlays.

Characterize rutting potential in thinasphalt overlays.

Instrumentation Plan

41

Longitudinal Asphalt Strain Gauge (Total: 2)

Pressure Cell (Total: 1)

LVDT (Total: 2)

Soil Compression Gauge (Total: 2)

HMA Temperature Sensor (Total: 3 T-type Thermocouples)

Type T thermocouples will be used for temperature measurements.

3”

11”

26”

31”

5 ft.5 ft.5 ft.5 ft.5 ft.5 ft.

Natural Soil

Compacted Natural Soil

I-3 (Layer -2)

PCC

HMA

I-3 (Layer -1)


Instrumentation

42

Pressure Cells (Geokon Inc.) To measure

pressure in sub-base (I-3) layer at both sides of transverse joints of PCC slabs

6 pressure cells have been installed in NJDOT sections

Instrumentation

43Instrumentation of NJDOT Sections: Pressure Cells

Instrumentation

44Instrumentation of NJDOT Sections: Leveling

Instrumentation

45Instrumentation of NJDOT Sections: Covering

Instrumentation

46Instrumentation of NJDOT Sections: Locating

Instrumentation (Thermocouples)

47

Thermocouples(Omega) To measure

temperature in subbase and overlays at various depths (2” interval for subbase and 0.5” interval in overlays)

48 thermocouples were installed in six Test sections

Instrumentation

48Instrumentation of NJDOT Sections: Preparation and Testing

Instrumentation

49Instrumentation of NJDOT Sections: Installation

Instrumentation


Instrumentation


Instrumentation

52Instrumentation of NJDOT Sections: Thermocouples

Thermocouple Installation (Surface Layer)

53

Thermocouple bed preparation, installation, and manual compaction

Instrumentation

54

Soil Compression Gauges (CTL Group) To measure vertical

deformation in sub-base (I-3) layer at both sides of transverse joints

12 soil compression gauges have been installed in NJDOT sections

Instrumentation

55Instrumentation of NJDOT Sections: Soil Compression Gauges

Instrumentation


Instrumentation


Instrumentation

58

Two LVDTs have been installed in PCC slabs

LVDTs used to measure lateral movement of the PCC slabs under accelerated loading.

Linear Variable Differential Transducers (LVDTs)

Instrumentation

59Instrumentation of NJDOT Sections: LVDTs

Instrumentation


Instrumentation


Instrumentation

62

12 strain gauges have been installed in NJDOT sections

Strain gauges utilized to simultaneously measure longitudinal and transverse strains in asphalt layer.

Asphalt Strain Gauges(Tokyo Sokki KM-100HAS H-gauge)

Instrumentation

63Instrumentation of NJDOT Sections: Wire trenches

Instrumentation

64Instrumentation of NJDOT Sections: ASGs

Instrumentation


Instrumentation


All Sections

67

68

Testing Plan

HVS Testing Protocol One section, out of the six, will be subjected to loading

using the HVS until failure (i.e., failing one section at atime).

Air Temp. around section is controlled using CREATEsCooling/Heating System (25oC).

Therefore, HVS loading will be conducted in thefollowing sequence: Section 1 loaded until failure,followed by Section 2, followed by Section 3, and soon.

69

9.5ME SMA HPTO 95/BRIC SMA/BRIC HPTO/BRIC

1 to 2 Months

1 to 2 Months

1 to 2 Months

1 to 2 Months

1 to 2 Months

1 to 2 Months

Testing Plan

70

Field Testing Steps

71

Verify Sensor Condition

Mark Loading Zone Cover Test Section

Perform HWD Testing

Field Testing Steps

72

Perform Profile Testing

Apply Sealing in HVS Station Cooling Trailer

Field Testing Steps

73

Ensure Testing Strip is Aligned

Station HVS on Section

Install Thermostat for Heaters Heat Control Thermostat

Field Testing Steps

74

Set-up Data Acquisition Station

Apply Side Insulation

Apply Rain Covers Attach Cooling Hoses

Heating System

75

Contains infrared heating elements.

Heating angle can be adjusted depending ondesired heating coverage within the section.

Used for controlling the air temperature aroundsection (within sealed enclosure).

Temperature Range:

Depends on ambient temperature.

On average, it can maintain the air temperaturearound the pavement to up to 120oF.

Heating System

76

Cooling System

77

Based on a vapor compression refrigeration cycle(i.e., uses a refrigerant to cool).

Works by cycling air through the enclosure coveringthe HVS. As a result, it is also used for controllingthe air temperature around section (within sealedenclosure).

Temperature Range:

Depends on ambient temperature.

On average, it can maintain the air temperaturearound the pavement to (comfortably) 32oF.

Cooling System

78

Cooling System

79

Data Collection Protocol The CREATEs cDAQ system will be utilized

to collect data from all sensors after theapplication of the following load passes:

80

Data Sampling Frequency1, 5, 10, 20, 30, 40, 50, 60, 70, 80, 90, 100, 125, 150, 175,200, 250, 300, 350, 400, 450, 500, 600, 700, 800, 900,1000, 1200, 1400, 1600, 1800, 2000, 2500, 3000, 3500,4000, 4500, 5000, 6000, 7000, 8000, 9000, 10000, …

Incremented by 5,000 after 10k Incremented by 10,000 after 40k

Incremented by 20,000 after 100k Incremented by 40,000 after 200k

A field test that is typicallyconducted evaluate thestructural integrity ofpavements.

The HWD “drops” (freefall) aweight on a particularlocation.

Geophones (seven) are used tomeasure deflections at variouslocations: Forming a DeflectionBasin.

HWD Testing

81

HWD Testing

82

Heavy Weight Deflectometer (HWD)testing will be conducted before HVSloading and after failure.

Six locations will be tested on eachsection.


12 ft

.

83

HWD Test ConfigurationsParameter Types No. of Drops Stress (psi) Load (lbf)

Load

Seating 3 60, 85,110, 140 7k, 9.5k, 12.5k, 16kDrop height 1 4 60 7kDrop height 2 4 85 9.5kDrop height 3 4 110 12.5kDrop height 4 4 140 16k

Loading Plate Diameter 12 in.

HWD Testing

Transverse Laser Profilometer Characterizes the transverse profiles of

pavements. Uses a laser distance measuring device and

collect data every 2 mm. Useful in measuring permanent deformation

(rutting) within the pavement structure.

84

Transverse Laser Profilometer

85

Transverse profiles will be measuredusing a laser profilometer on daily basis.

Seven locations will be tested as shown inthe schematic below:


12 ft

.

Visual Inspection and Mapping

86

In addition, visual inspection will beconducted to collect information about thesection.

That is, crack maps and pictures of cracksas loading progresses.

87


88


89

Preliminary Testing Results

Section Temperature (Before Testing)

90

12 ft.

1 ft.

2 ft.

4 ft.

7 ft.

Temperature (Surface Thermocouples)

91

12 ft.

1 ft.

2 ft.

4 ft.

7 ft.

Temperature (HMA Embedded Thermocouples)

92

Load

ing

Soil Compression Gauge (Gauge 1)

93

Load

ing


94

Load

ing


95

Loading

Slab 1 Slab 2

LVDT 1 (Horizontal Joint Opening)

96

Load

ing

LVDT 2 (Horizontal Joint Opening)

97

Load

ing

Pressure Cell

98

Load

ing

HWD Testing (Deflection Basins)

99

5 ft.

5 ft.

5 ft.

5 ft.

5 ft.

5 ft.

12 ft.

12

3

4

5

6

100

Final Remarks

Final Remarks

101

The Heavy Vehicle Simulator is capable ofsimulating damage applied by truck andaircraft wheels in an accelerated fashion.

Full-Scale accelerated testing of pavementsprovides valuable information about fieldperformance.

Data extracted from sensors can be used todevelop performance measures forevaluating pavement performance.

102

103

Ayman Ali, Ph.D.Tel: (908) 283-0467

Email: [email protected]/creates

mailto:[email protected]

http://www.rowan.edu/creates

Documents

Estimating the Life Expectancy of Thin Asphalt Overlays in New … · In this presentation… WhyThinOverlays? StudyGoals&Objectives ResearchApproach Construction of Sections & Instrumentation