8/20/2019 Especificaciones Sssangyong Rexton 2.7 Xdi Cr

1/2

Technical data on the vehicle

Make

Model

Year

Engine

SsangYong

Rexton 2,7 Xdi

665 925

2004-2006

Date:

Owner

Registration No.

VIN

1. Reg. Date

05-08-2011

Variant

Technical item Data

Engine

Engine ID code D27DT (665.925)

Number of cylinders R5 i

Number of valves 20, DOHC

Capacity/ (bore/ stroke) 2696 cm³ (86,20 / 92,40)

Compression ratio 18,0: 1

Max. output kW (din hp)/ rpm 121 (165)/ 4000

Max. torque NM/ rpm 340/ 1800 - 3250

Engine code location Left side, underneat engine mount

Vehicle Identification Number location Frame behind right front tireVehicle identification plate location Driver´s door sill

Valve clearance, inlet (cold/ hot) (Hydraulic)

Valve clearance, exhaust (cold/ hot) (Hydraulic)

Piston height over block, mm 0,765 - 1,055

Cylinder head height new, mm 142,9 - 143,1

Cylinder head height minimum, mm 142,4

Cylinder head max. distortion, mm 0,08

Valve height in cylinder head, mm 0,1 - 0,7

Compression pressure, bar 32.0 (Min. 18.0) Max. difference 3.0

Oil pressure running, bar 2,5 - 3,0

Radiator cap opening pressure, bar 1,2 - 1,5Thermostat opens, °C 85° C

Timing chain: i

Noise measurement, dB(A) at rpm 83/ 3000

Drive belt i

Engine management

Engine management system Delphi Common rail

Diagnostic connector Under steering wheel, left side i

Injector/ injector type Delphi / PWM

Adjustment method Electronic i

Injection order 1 - 2 - 4 - 5 - 3 (Cylinder 1 at timing gear) i

Injection timing mark location Belt pulleyElectrical system

Battery 12 V 90 Ah

Starter motor current (cranking), A 160 A

Voltage relay, Volt at/ amp. 14,6 V

Terminal definitions DIN 72 552

Alternator max, A 140

Glow plug voltage/ drop resistor 11.5 V/

Wheel alignment

Toe-in, ° 0° 15' ± 15'

Camber° 0° 00' ± 30' i

Camber, max. difference on R and L side 30'Caster° 2° 27' ± 30' i

Caster, max. difference on R and L side 30'

Rear camber° No factory setting i

Rear toe-in ° No factory setting i

Tyre size 255/ 65 R16 (235/ 75 R16) 255/ 70 R16 (225/ 75 R15)

8/20/2019 Especificaciones Sssangyong Rexton 2.7 Xdi Cr

2/2

Technical item Data

Wheel alignment

Tyre pressure, front/ rear, bar 2,0

Free play in suspension parts Factory data i

Wheel offset, mm 7J x 16 =43 (7J x15 = 29)

Top speed 170 - 177

Tightening torques

Tightening, NM Torque standards

Cylinder head bolts, stage 1, Nm 20 Nm (M8 bolts 25 Nm) i

Cylinder head bolts, stage 2, Nm 85

Cylinder head bolts, stage 3, Nm + 90°

Cylinder head bolts, stage 4, Nm + 90°

Cylinder head bolts, stage 5, Nm + 90° i

Main bearings, Nm 55 Nm + 90°

Connection rod bearings, Nm 40 Nm + 90°

Flywheel, Nm 45 Nm + 90°

Crankshaft pulley centre bolt, Nm 325 Nm + 90°

Camshaft pulley centre bolt, Nm 25 Nm + 90°

Camshaft bearings, Nm 25

Pump pulley, Nm 20 Nm + 90° (Center nut 65 Nm)

Timing belt tensioner, Nm (Chain tensioner 65 Nm)

Nozzle clamp, Nm 9 Nm + 190°

Nozzle line, Nm 40

Glow plug 15

Wheel nuts/ bolts, Nm 130

Brakes

Front, thickness new, mm 26,0

Front, minimum thickness, mm 23,4

Rear, disc thickness new, mm 10,4

Rear, disc thickness minimum, mm 8,5

Rear, drum diameter new, mm 254,0

Rear, drum diameter maximum, mm 255,5

Min. brake lining thickness, front, mm 2,0

Min. brake lining thickness, rear, mm 1.0

Capacities

Engine oil/ - incl. f ilter, litre  / 7,0 - 8,0 (SAE 5W30) MB 229,3

Manual transmission, litre 3,6 ( ATF Dexron III )

Transfer case, litre 1,4 ( ATF Dexron III )

Automatic transmission, litre 8,0 ( ATF 3353 ) 5 gear

Automatic transmission, litre. variant 2 4,5 ( ATF Dexron III ) 4 gear

Final drive, litre Front 1.5. Rear 2.2 SAE 75W 85 API GL-5

Power steering, litre 1,1 ( ATF Dexron III )

Cooling system, litre 11,5

Fuel tank, litre 80

A/C fluid, type/ gram R134a/ 850

Environmental parametres

Idle speed, rpm 750 ± 50

Smoke gas density (K-value) 1,02

EU norm Euro 3

Remarks

n  Order No.:

Mechanicn

n n