To Check Major alarmAllip: acl=a2; This command shows mains power failure, tre faults,Outage e.t.cTo check critical alarmAllip: acl=a1; this command shows low fuel, Common alarms, if is Gen set ON, AC alarms, rectifier alarms e.t.cTo check Minor alarmAllip: acl=a3;RXMFP: MO=RXOCF-tgno; this shows battery backup also cf statusRXMOP: MOTY=RXOTG; this printout all sites corresponding their TGRXCDP: MO=RXOTG-TGNO; shows status of site (if the site is up shows configured status and if the site is down shows blocked status) To check the tg frequency type- rxcdp:mo=rxotg-tgno.; tgno- transceiver group numberTo check in which sector or channel group the tg is present- rxmop:mo=rxotrx-17-2;To print site name- rxmop:mo=rxotg-tgno.;To check frequency of the cell- rlcfp:cell=cellno.;To active unused cell- rlstc:cell=cellno,chgr=0 or 1,state=halted;- rlstc:cell=cellno,chgr=0 or 1,state=active;To check for traffic in the sector- rlcrp:cell=cellno.;To change handover relations- rlmfc:cell=cellno,mbcchno=mbcchno,listtype=listtype;listtype can be active & idlembcchno=frequency number- rlmfp:cell=cellno;cell measurement frequenciesTo load software remotely- rxpli:mo=rxotg-tgno,uc;To check if loading of s/w is over- rxmsp:mo=rxocf-tgno;To check cell ID of the cell- rxtcp:mo=rxotg-tgno;Cell printing- rlcrp:cell=all;Reseting the site- rxbli:mo=rxocf-tgno,force;- rxble:mo=rxocf-tgno;To know the DIP no of the site- rxapp:mo=rxotg-tgno;- ntcop:snt=all; or ntcop=etm2-tgno;To check if there is any signaling link down in the MSCs- c7ltp:ls=all; If there is restoring then the signaling is not workingTo check CGI if defined correctly- mgcep:cell=cellID;To change CGI- 1. Halt cell rlstc:cell=cellID,chgr=0 or 1,state=halted;- 2. rldec:cell=cellID,cgi=640-05-9-cellID;- 3. Activate cell rlstc:cell=cellID,chgr=0 or 1,state=active;To check E1 for sites in the BSC- dtstp:dip=all;To check which cell are in extended range- rldep:cell=all,xrange;To check which cells are set in OL/UL- rldgp:cell=cellno;- rlcfp:cell=cellno.;To delete a sector1st block the trx i.e. rxbli:mo=rxotrx-30-4,subord,force;2nd put trx out of service i.e. rxese:mo=rxotrx-30-4,subord;3rd rxmoe:mo=rxots-30-4-0&&-7; rxmoe:mo=rxotx-30-4; rxmoe:mo=rxorx-30-4; rxmoe:mo=rxotrx-30-4;4th rlstc:cell=cellno,state=halted,chgr=0 or 1; rxtce:mo=rxotg-30,cell=cellno,chgr=0 or 1; rlsle:cell=cellno,perm; rldee:cell=cellno;To check if the cell is active or halted- rlstp:cell=cellno;To get TG number- rxtcp:moty=rxotg,cell=cellno;To check the TS- rxmsp:moty=rxots;To check which faulty code comes from a faulty tre- rxmfp:mo=rxotx-tgno-trxno;To lock a sector- rlstc:cell=cellno,state=halted;To unlock a sector- rlstc:cell=cellno,state=active;Upgrading a sector