ER-TFT024-3 - buydisplay.com · ER-TFT024-3 2.4”TFT LCD Display with no Touch Panel. ER-TP024-3 2.4”Resistive Touch Panel ER-TPC024-3 2.4”Capacitive Touch Panel with Controller.(Under

TFT LCD Display Datasheet ER-TFT024-3

URL: www.buydisplay.com Document Name: ER-TFT024-3 Datasheet-V1.0 Page: 1 of 24

buydisplay.comEastRising

ER-TFT024-3 TFT LCD Display Datasheet

3B3B

EastRising Technology Co., Limited

Attention:

A. Some specifications of IC are not listed in this datasheet. Please refer to the IC datasheet for more details.

B. The related documents for interfacing, demo code, IC datasheet are all available, please download from our web.

C. Please pay more attention to “INSPECTION CRITERIA” in this datasheet. We assume you already agree with these

criterions when you place an order with us. No more recommendations.

REV Description Release Date

1.0 Preliminary Release Jun-19-2014

011

ISO9001Registered Company

siraCERTIFICATION




CONTENTS 1. ORDER INFORMATION - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 04

1.1 Order Number - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 04

1.2 Image - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -- - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 04

2. SPECIFICATION - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 05

2.1 Display Specification - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 05

2.2 Mechanical Specification - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 05

2.3 Electrical Specification - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 05

2.4 Optical Specification - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 05

3. OUTLINE DRAWING - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 06

3.1 ER-TFT024-3 with No Touch Panel Outline Drawing - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 06

3.2 ER-TFT024-3 with Resistive Touch Panel Outline Drawing - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 07

3.3 ER-TFT024-3 with Capacitive Touch Panel Outline Drawing - - - - - - - - - - - - -- - - - - - - - -- - - - - - - - - - - - 08

4. ELECTRICAL SPEC - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 09

4.1 Pin Configuration - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 09

4.2 Absolute Maximum Ratings - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 11

4.3 Electrical Characteristics - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 11

4.4 Backlight Characteristics - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 11

5. INSPECTION CRITERIA - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 12

5.1 Acceptable Quality Level - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 12

5.2 Definition of Lot - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 12

5.3 Condition of Cosmetic Inspection - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 12

5.4 Module Cosmetic Criteria - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 13

5.5 Screen Cosmetic Criteria (Non-Operating) - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 15

5.6 Screen Cosmetic Criteria (Operating) - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 16 6. PRECAUTIONS FOR USING - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 18

6.1 Handling Precautions - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 18

6.2 Power Supply Precautions- - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 19

6.3 Operating Precautions- - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 19

6.4 Mechanical/Environmental Precautions - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 19

6.5 Storage Precautions - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 19

6.6 Others- - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 20




7. USING LCD MODULES - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 20

7.1 Liquid Crystal Display Modules - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 20

7.2 Installing LCD Modules - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 21

7.3 Precaution for Handling LCD Modules - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 21

7.4 Electro-Static Discharge Control- - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 21

7.5 Precaution for Soldering to EastRising LCM- - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 21

7.6 Precaution for Operation - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 22

7.7 Limited Warranty - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 22

7.8 Return Policy - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 22

8. IMAGE STICKING - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 23

8.1 What is Image Sticking? - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 23

8.2 What causes Image Sticking? - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 23

8.3 How to Avoid Image Sticking? - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 24

8.4 How to Fix the Image Sticking? - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 24

8.5 Is Image Sticking Covered by EastRising RMA Warranty？- - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 24




1. ORDERING INFORMATION 1.1 Order Number

Part Number(Order Number) Description

ER-TFT024-3 2.4”TFT LCD Display with no Touch Panel.

ER-TP024-3 2.4”Resistive Touch Panel

ER-TPC024-3 2.4”Capacitive Touch Panel with Controller.(Under Development)

ER-CON50HT-1 ZIF Connector with 50 Pins 0.5mm Pitch SMD Top Contact

ER-DBT024-3 8051 Microcontroller Development Board&Kit for ER-TFT024-3

1.2 Image

Under Development

Image for ER-TFT024-3 ↑ Image for ER-TP024-3 ↑ Image for ER-TPC024-3 ↑

Image for ER-CON50HT-1 ↑ Image for ER-DBT024-3 ↑




2. SPECIFICATION

2.1 Display Specification

Item Standard Value Unit

Display Format 240X(RGB)X320 Dots --

Display Connector FPC --

FPC Connector 50 Pin,0.5mm Pitch, SMD Horizontal Type Top contact --

Operating Temperature -20 ~ +70 ℃

Storage Temperature -30 ~ +80 ℃

Touch Panel Optional Yes --

Sunlight Readable No --

2.2 Mechanical Specification H HHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHH


Diagonal Size 2.4 Inch

Outline Dimension with FPC Folded 42.72(W)x59.26(H)x2.6(T) mm

Visual Area 38.72x50.96 mm

Active Area 36.72X48.96 mm

Dot Pitch 0.153(W)x0.153(H) mm

2.3 Electrical Specification


IC Package COG --

Controller ILI9341 --

Interface 8080 8-bit/9-bit/16-bit/18-bit Parall,3/4-Wire Serial, RGB --

Response Time (Typ) 25 MS

2.4 Optical Specification H HHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHH


LCD Type TFT-LCD / Transmissive / TN --

Viewing Angle Range Left:70 , Right:70 , Up:60 , Down:70 Deg

Colors 65k/262k --

Contrast Ratio (Typ) 500:1 --

Brightness (Typ) 300 Cd/m2




3. OUTLINE DRAWING

3.1 ER-TFT024-3 with No Touch Panel Outline Drawing

LED

- K4

LED

-K3

LED

- K2

LED

-A

LED

- K1

U=

3.2V

, I=

4x20

mA

150

0.3±

0.03

CO

ND

UC

TOR

STIF

FEN

ER

150

RG

BR

RG

B

RG

R

1:10

2,60

±0.

1BL

42,

72±

0.2

LCD

V.A

38,

72

LCD

A.A

36,7

2

BL 59,26±0.2LCD V.A 50,96

LCD A.A48,96

2,00

3,00

1,50

2,50

26,90±0.3

25,5

0

11,60 13,50

3,50

2,00

0,80

8,00

30,2615,00

25,5

0

5,50

0,05

1

0,153

RG

BR

GB

RG

BR

GB

RG

BR

GB

Vie

win

g D

irec

tion

12:

00

2.4

"24

0x32

0 do

ts

1D

O N

OT

SCA

LE T

HIS

DR

AW

ING

.

MO

DEL

NU

MBE

R :

DW

NJI

M

APP

RO

VA

LS

CH

K

APP

Au g

-4-1

4

DA

TE

PRO

JEC

TIO

NSH

EET:

GEN

ERA

L TO

L.

SCA

LE:

N.T

.S.

UN

ITS

MM

buydisplay.co

m

Eas

tRis

ing

EA

ST

RIS

ING

TE

CH

NO

LOG

Y C

O.,L

TD

ER-T

FT02

4-3

Web

: ww

w.b

uydi

spla

y.co

m

Em

ail:

sale

s@bu

ydis

play

.comD

ATE

REV

DES

CR

IPTI

ON

DES

IGN

1'ST

DEG

INA

ug-0

4-20

14JI

MA B

1. U

nit:

mm

旭日

东方

科技

有限

公司




3.2 ER-TFT024-3 with Resistive Touch Panel Outline Drawing

1D

O N

OT

SCA

LE T

HIS

DRA

WIN

G.

MO

DEL

NU

MBE

R :

DW

NJI

M

APP

ROV

ALS

CH

K

APP

Aug

-4-1

4

DA

TE

PRO

JEC

TIO

NSH

EET:

GE N

ERA

L TO

L.

SCA

LE:

N.T

.S.

UN

ITS

MM

buydisplay.com

Eas

tRis

ing

EA

ST

RIS

ING

TE

CH

NO

LOG

Y C

O.,L

TD

ER-T

FT02

4-3

Web

: ww

w.b

uydi

spla

y.co

m

Em

ail:

sale

s@bu

ydis

play

.com

150

0 .3±

0.03

CO

ND

UC

TOR

STIF

FEN

ER1

50

RG

BR

RG

B

RG

R

1:10

PIN

1PI

N4

YU YD

XLXR

3,80

±0.

2

BL 4

2,72

±0.

2R

TP 4

2,52

RTP

Silv

er w

ire39

,52

RTP

V.A

38,

72

LCD

A.A

36,7

2

BL(RTP) 59,26±0.2RTP Silver wire 54,86

RTP V.A 50,30RTP A.A53,16

LCD A.A48,96

RTP

A.A

37,

72

1,60

±0.

32,

00±

0.3

2,50

±0.

33,

00±

0.3

1,60±0.3

2,00±0.32,50±0.3

2,50±0.3

26,90±0.3

25,5

0

11,60 13,50

3,50

2,00

0,80

8,00

30,2615,00

25,5

0

5,50

0,05

1

0,153

RG

BR

GB

RG

BR

GB

RG

BR

GB

LED

-K4

LED

-K3

LED

-K2

LED

-A

LED

-K1

U=

3.2V

, I=

4x20

mA

1. U

nit:

mm

2. R

TP=

Res

istiv

e To

uch

Pane

l

Vie

win

g D

irec

tion

12:

00

2.4

"24

0x32

0 do

ts

旭日

东方

科技

有限

公司




3.3 ER-TFT024-3 with Capacitive Touch Panel Outline Drawing

Under Development




4. ELECTRICAL SPEC

4.1 Pin Configuration

Pin No Pin Name Descriptions

1 LEDA Anode for LED backlighting

2 LEDK1 Cathode No.1 for LED backlighting




6~9 IM0~IM3 Select Interface Mode (Refer to Note1)

10 RESET Reset Pin

11 VSYNC Frame Synchronizing Signal For RGB Interface

12 HSYNC Line Synchronizing Signal For RGB Interface

13 DOTCLK Dot Clock Signal For RGB Interface

14 DE Data Enable Signal For RGB Interface

15-32 DB17-DB0 DATA BUS

33 SDO Serial Output Signal

34 SDI Serial Input Signal

35 RD Read execution control pin

36 WRX(D/CX) Write execution control pin ; Serial Register select s Signal

37 D/CX(SCL) Register select signal; Serial Interface Clock

38 CSX Chip Select Signal

39 TE Tearing effect out pin synchronize MPU to frame writng

40 VDDI Power Supply to the interface pins ,provide with 2.8V

41 VDDI Power Supply to the interface pins ,provide with 2.8V

42 VCI Logic power ,provide with 2.8V

43 GND Ground

44 X+ Touch panel output

45 Y+ Touch panel output

46 X- Touch panel output

47 Y- Touch panel output




48~50 GND Ground

Note 1: Select the MCU Interface Mode

Pin in Use IM3 IM2 IM1 IM0 MCU-Interface Mode

Register/content GRAM

0 0 0 0 8080 MCU 8-bit Bus Interface I D[7:0] D[7:0],WRX,RDX,CSX,D/CX




0 1 0 1 3-wire 9-bit data serial Interface I SCL,SDA,CSX

0 1 1 0 4-wire 8-bit data serial Interface I SCL,SDA,D/CX,CSX

1 0 0 0 8080 MCU 16-bit Bus Interface II D[8:1] D[17:0],D[8:1],WRX,RDX,CSX,D/CX

1 0 0 1 8080 MCU 8-bit Bus Interface II D[17:10] D[17:10],WRX,RDX,CSX,D/CX



1 1 0 1 3-wire 9-bit data serial Interface II SCL,SDI,SDO,CSX

1 1 1 0 4-wire 8-bit data serial Interface II SCL,SDI,D/CX,SDO,CSX




4.2 Absolute Maximum Ratings

Item Symbol Min Typ Max Unit

Power Supply Voltage VCI -0.3 - +4.6 V

Logic Signal Voltage VDDI -0.3 - +4.6 V

Operating Temperature TOP -20 - +70 °C

Storage Temperature TST -30 - +80 °C

Humidity RH - - 90%(Max60°C) RH

4.3 Electrical Characteristics

Item Symbol Min Typ Max Unit

Power Supply Voltage VCI 2.5 2.8 3.3 V

Logic Signal l/O Voltage VDDI 1.65 2.8 3.3 V

Input Voltage 'H' Level VIH 0.7VDDI - VDDI V

Input Voltage 'L' Level VIL VSS - 0.3VDDI V

Output Voltage 'H' Level VOH 0.8VDDI - VDDI V

Output Voltage 'L' Level VCL VSS0 - 0.2VDDI V

4.4 Backlight Characteristics

Item Symbol Condition Min Typ Max Unit

Supply Voltage Vf Lf=80mA - 3.2 3.4 V

Supply Current - - - - - MA

Reverse Voltage Vf - - - - V

Normal lpn - 70 80 Forward Current

Dimming lpd 4-chip Parallel

- - - MA




5. INSPECTION CRITERIA

5.1 Acceptable Quality Level

Each lot should satisfy the quality level defined as follows

Partition AQL Definition

A. Major 0.4% Functional defective as product

B. Minor 1.5% Satisfy all functions as product but not satisfy cosmetic standard

5.2 Definition of Lot

One lot means the delivery quantity to customer at one time.

5.3 Condition of Cosmetic Inspection

◆ INSPECTION AND TEST

-FUNCTION TEST

-APPEARANCE INSPECTION

-PACKING SPECIFICTION

◆ INSPECTION CONDITION

- Put under the lamp (20W) at a distance 100mm from

- Tilt upright 45 degree by the front (back) to inspect LCD appearance.

◆ AQL INSPECTION LEVEL

- SAMPLING METHOD: MIL-STD-105D

- SAMPLING PLAN: SINGLE

- MAJOR DEFECT: 0.4% (MAJOR)

- MINOR DEFECT: 1.5% (MINOR)

- GENERAL LEVEL: II/NORMAL




5.4 Module Cosmetic Criteria

No. Item Judgment Criterion Partition

1 Difference in Spec. None allowed Major

2 Pattern Peeling No substrate pattern peeling and floating Major

No soldering missing Major

No soldering bridge Major

3 Soldering Defects

No cold soldering Minor

4 Resist Flaw on Substrate Invisible copper foil(￠0.5mm or more)on substrate pattern Minor

No soldering dust 5 Accretion of Metallic

Foreign Matter No accretion of metallic foreign matters(Not exceed￠0.2mm)

Minor

6 Stain No stain to spoil cosmetic badly Minor

7 Plate Discoloring No plate fading, rusting and discoloring Minor

Solder Amount

1.Lead Parts

a. Soldering side of PCB

Solder to form a’Filet’all around the lead.

Solder should not hide the lead form perfectly.(too much)

b.Components side

(In case of ‘Through Hole PCB’)

Solder to reach the Components

side of PCB

Minor

2.Flat Packages Either‘toe’(A) or ‘heal’ (B) of

the lead to be covered by Filet’.

Lead form to be assume over

solder.

Minor

8

3.Chips (3/2) H≧h≧(1/2)H Minor

h H

A B




9 Backlight Defects 1.Light fails or flickers.(Major)

2. Color and luminance do not correspond to specifications.

(Major)

3.Exceeds standards for display’s blemishes, foreign matter,

dark lines or scratches.(Minor)

See

list

←

10 PCB Defects Oxidation or contamination on connectors.*

2. Wrong parts, missing parts, or parts not in specification.*

3.Jumpers set incorrectly.(Minor)

4.Solder(if any)on bezel, LED pad, zebra pad, or screw hole

pad is not smooth.(Minor)

*Minor if display functions correctly. Major if the display fails.

See

list

←

11 Soldering Defects 1. Unmelted solder paste.

2. Cold solder joints, missing solder connections, or oxidation.*

3. Solder bridges causing short circuits.*

4. Residue or solder balls.

5. Solder flux is black or brown.

*Minor if display functions correctly. Major if the display fails.

Minor




5.5 Screen Cosmetic Criteria (Non-Operating)

No. Defect Judgment Criterion Partition

1 Spots In accordance with Screen Cosmetic Criteria (Operating) No.1. Minor

2 Lines In accordance with Screen Cosmetic Criteria (Operation) No.2. Minor

Size: d mm Acceptable Qty in active area

d≦0.3

0.3<d≦1.0

1.0<d≦1.5

1.5<d

Disregard

3

1

0

Minor 3 Bubbles in Polarizer

4 Scratch

In accordance with spots and lines operating cosmetic criteria, When the light

reflects on the panel surface, the scratches are not to be remarkable.

Minor

5 Allowable density Above defects should be separated more than 30mm each other. Minor

6 Coloration Not to be noticeable coloration in the viewing area of the LCD panels.

Back-lit type should be judged with back-lit on state only.

Minor

7 Contamination Not to be noticeable. Minor




5.6 Screen Cosmetic Criteria (Operating)


A) Clear

Size:d mm Acceptable Qty in active area

d≦0.1

0.1<d≦0.2

0.2<d≦0.3

0.3<d

Disregard

6

2

0

Note: Including pin holes and defective dots which must be within one pixel

Size.

B) Unclear

Size:d mm Acceptable Qty in active area

1 Spots

d≦0.2

0.2<d≦0.5

0.5<d≦0.7

0.7<d

Disregard

6

2

0

Minor

2 Lines A) Clear

Note: () – Acceptable Qty in active area

L - Length (mm)

W -Width(mm)

∞-Disregard

B) Unclear

Minor

Clear’ = The shade and size are not changed by Vo.

Unclear’= The shade and size are changed by Vo.

L 5.0

2.0

8

0.02 0.05 0.1W

See No.1

(0)

(6)

L 10.0

2.0

8

(6)

(0)

0.05 0.3 0.5

See No.1W





3 Rubbing line Not to be noticeable. Minor

4 Allowable density Above defects should be separated more than 10mm each other. Minor

5 Rainbow Not to be noticeable. Minor

6 Dot size To be 95%~105%of the dot size (Typ.) in drawing.

Partial defects of each dot (ex.pin-hole) should be treated as spot.

(see Screen Cosmetic Criteria (Operating) No.1)

Minor

7 Brightness

(only back-lit

Module)

Brightness Uniformity must be BMAX/BMIN≦2

- BMAX : Max.value by measure in 5 points

- BMIN : Min.value by measure in 5 points

Divide active area into 4 vertically and horizontally.

Measure 5 points shown in the following figure.

Minor

8 Contrast

Uniformity

Contrast Uniformity must be BmAX/BMIN≦2

Measure 5 points shown in the following figure.

Dashed lines divide active area into 4 vertically and horizontally.

Measuring points are located at the inter-sections of dashed line.

Note: BMAX – Max.value by measure in 5 points.

BMIN – Min.value by measure in 5 points.

O – Measuring points in ￠10mm.

Minor

Note:

(1) Size: d=(long length + short length)/2

(2) The limit samples for each item have priority.

(3) Complexed defects are defined item by item, but if the number of defects is defined in above table, the total number should

not exceed 10.




(4) In case of ‘concentration’, even the spots or the lines of ‘disregarded’ size should not be allowed. Following three

situations

Should be treated as ‘concentration’.

-7 or over defects in circle of ￠5mm.

-10 or over defects in circle of ￠10mm

-20 or over defects in circle of ￠20mm

6. PRECAUTIONS FOR USING

6.1 Handling Precautions

◆ This device is susceptible to Electro-Static Discharge (ESD) damage. Observe Anti-Static precautions.

◆ EastRising display panel is made of glass. Do not subject it to a mechanical shock by dropping it or impact.

◆ If EastRising display panel is damaged and the liquid crystal substance leaks out, be sure not to get any in your mouth.

If the substance contacts your skin or clothes, wash it off using soap and water.

◆ Do not apply excessive force to the EastRising display surface or the adjoining areas since this may cause the color

tone to vary.

◆ The polarizer covering the EastRising display surface of the LCD module is soft and easily scratched. Handle this

polarizer carefully.

◆ If EastRising display surface becomes contaminated, breathe on the surface and gently wipe it with a soft dry cloth. If

it is heavily contaminated, moisten cloth with one of the following Isopropyl or alcohol.

◆ Solvents other than those above-mentioned may damage the polarizer. Especially, do not use the Water.

◆ Exercise care to minimize corrosion of the electrode. Corrosion of the electrodes is accelerated by water droplets,

moisture condensation or a current flow in a high-humidity environment.

◆ Install the EastRising LCD Module by using the mounting holes. When mounting the LCD module make sure it is free

of twisting, warping and distortion. In particular, do not forcibly pull or bend the cable or the backlight cable.

◆ Do not attempt to disassemble or process EastRising LCD module.

◆ NC terminal should be open. Do not connect anything.

◆ If the logic circuit power is off, do not apply the input signals.

◆ To prevent destruction of the elements by static electricity, be careful to maintain an optimum work environment.

-Be sure to ground the body when handling EastRising LCD modules.

-Tools required for assembling, such as soldering irons, must be properly grounded.

-To reduce the amount of static electricity generated, do not conduct assembling and other work under dry

conditions.

-The LCD module is coated with a film to protect the display surface. Exercise care when peeling off this protective film

since static electricity may be generated.




6.2 Power Supply Precautions

338B335B332B42B461B458B455B339B336B333B◆ Identify and, at all times, observe absolute maximum ratings for both logic and LC drivers. Note that there is some

variance between models.

◆ Prevent the application of reverse polarity to VDD and VSS, however briefly.

◆ Use a clean power source free from transients. Power-up conditions are occasionally jolting and may exceed the

maximum ratings of EastRising modules.

◆ The VDD power of EastRising module should also supply the power to all devices that may access the display. Don’t

allow the data bus to be driven when the logic supply to the module is turned off.

6.3 Operating Precautions

345B342B339B◆ DO NOT plug or unplug EastRising module when the system is powered up.

◆ Minimize the cable length between EastRising module and host MPU.

◆ For models with backlights, do not disable the backlight by interrupting the HV line. Unload inverters produce voltage

extremes that may arc within a cable or at the display.

◆ Operate EastRising module within the limits of the modules temperature specifications.

349B346B343B44B452B449B446B6.4 Mechanical/Environmental Precautions

350B347B344B◆ Improper soldering is the major cause of module difficulty. Use of flux cleaner is not recommended as they may seep

under the electrometric connection and cause display failure.

◆ Mount EastRising module so that it is free from torque and mechanical stress.

◆ Surface of the LCD panel should not be touched or scratched. The display front surface is an easily scratched, plastic

polarizer. Avoid contact and clean only when necessary with soft, absorbent cotton dampened with petroleum

benzene.

◆ Always employ anti-static procedure while handling EastRising module.

◆ Prevent moisture build-up upon the module and observe the environmental constraints for storage tem

◆ Do not store in direct sunlight

◆ If leakage of the liquid crystal material should occur, avoid contact with this material, particularly ingestion. If the

body or clothing becomes contaminated by the liquid crystal material, wash thoroughly with water and soap.

6.5 Storage Precautions

When storing the LCD modules, avoid exposure to direct sunlight or to the light of fluorescent lamps.

Keep EastRising modules in bags (avoid high temperature / high humidity and low temperatures below 0 ºC.

Whenever possible, EastRising LCD modules should be stored in the same conditions in which they were shipped from

our company.




6.6 Others

363B360B357BLiquid crystals solidify under low temperature (below the storage temperature range) leading to defective orientation or

the generation of air bubbles (black or white). Air bubbles may also be generated if the module is subject to a low

temperature.

If EastRising LCD modules have been operating for a long time showing the same display patterns, the display patterns

may remain on the screen as ghost images and a slight contrast irregularity may also appear. A normal operating status

can be regained by suspending use for some time. It should be noted that this phenomenon does not adversely affect

performance reliability.

To minimize the performance degradation of the LCD modules resulting from destruction caused by static electricity etc.,

exercise care to avoid holding the following sections when handling the modules.

-Exposed area of the printed circuit board.

-Terminal electrode sections. 69B368B466B365B463B 362B

7. USING LCD MODULES HHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHH HHH

369B366B363B31B450B447B444B7.1 Liquid Crystal Display Modules

EastRising LCD is composed of glass and polarizer. Pay attention to the following items when handling.

◆ Please keep the temperature within specified range for use and storage. Polarization degradation, bubble generation

or polarizer peel-off may occur with high temperature and high humidity.

◆ Do not touch, push or rub the exposed polarizers with anything harder than an HB pencil lead (glass, tweezers, etc.).

◆ N-hexane is recommended for cleaning the adhesives used to attach front/rear polarizers and reflectors made of

organic substances which will be damaged by chemicals such as acetone, toluene, ethanol and isopropyl alcohol.

◆ When EastRising display surface becomes dusty, wipe gently with absorbent cotton or other soft material like chamois

soaked in petroleum benzin. Do not scrub hard to avoid damaging the display surface.

◆ Wipe off saliva or water drops immediately, contact with water over a long period of time may cause deformation or

color fading.

◆ Avoid contacting oil and fats.

◆ Condensation on the surface and contact with terminals due to cold will damage, stain or dirty the polarizers. After

products are tested at low temperature they must be warmed up in a container before coming is contacting with room

temperature air.

◆ Do not put or attach anything on EastRising display area to avoid leaving marks on.

◆ Do not touch the display with bare hands. This will stain the display area and degradate insulation between terminals

(some cosmetics are determinated to the polarizers).

◆ As glass is fragile. It tends to become or chipped during handling especially on the edges. Please avoid dropping.




7.2 Installing LCD Modules

384B381B378B42B447B444B441B385B382B379B◆ Cover the surface with a transparent protective plate to protect the polarizer and LC cell.

◆ When assembling the LCM into other equipment, the spacer to the bit between the LCM and the fitting

plate should have enough height to avoid causing stress to the module surface, refer to the individual specifications

for measurements. The measurement tolerance should be±0.1mm.

7.3 Precaution for Handling LCD Modules

Since EastRising LCM has been assembled and adjusted with a high degree of precision; avoid applying excessive shocks

to the module or making any alterations or modifications to it.

◆ Do not alter, modify or change the shape of the tab on the metal frame.

◆ Do not make extra holes on the printed circuit board, modify its shape or change the positions of components to be

attached.

◆ Do not damage or modify the pattern writing on the printed circuit board.

◆ Absolutely do not modify the zebra rubber strip (conductive rubber) or heat seal connector.

◆ Except for soldering the interface, do not make any alterations or modifications with a soldering iron.

◆ Do not drop, bend or twist EastRising LCM.

7.4 Electro-Static Discharge Control

Since this module uses a CMOS LSI, the same careful attention should be paid to electrostatic discharge as for an

ordinary CMOS IC.

◆ Make certain that you are grounded when handing LCM.

◆ Before remove LCM from its packing case or incorporating it into a set, be sure the module and your body have the

same electric potential.

◆ When soldering the terminal of LCM, make certain the AC power source for the soldering iron does not leak.

◆ When using an electric screwdriver to attach LCM, the screwdriver should be of ground potentiality to minimize as

much as possible any transmission of electromagnetic waves produced sparks coming from the commutator of the

motor.

◆ As far as possible make the electric potential of your work clothes and that of the work bench the ground potential.

◆ To reduce the generation of static electricity be careful that the air in the work is not too dried. A relative humidity of

50%-60% is recommended.

7.5 Precaution for Soldering to EastRising LCM

◆ Observe the following when soldering lead wire, connector cable and etc. to the LCM.

-Soldering iron temperature : 280℃±10℃

-Soldering time: 3-4 sec.

-Solder: eutectic solder.

If soldering flux is used, be sure to remove any remaining flux after finishing to soldering operation. (This does not

apply in the case of a non-halogen type of flux.) It is recommended that you protect the LCD surface with a cover

during soldering to prevent any damage due to flux spatters.




◆ When soldering the electroluminescent panel and PC board, the panel and board should not be detached more than

three times. This maximum number is determined by the temperature and time conditions mentioned above, though

there may be some variance depending on the temperature of the soldering iron.

◆ When remove the electroluminescent panel from the PC board, be sure the solder has completely melted, the

soldered pad on the PCs board could be damaged.

7.6 Precaution for Operation

413B410B407B◆ Driving the EastRising LCD in the voltage above the limit shortens its life.

◆ Response time is greatly delayed at temperature below the operating temperature range. However, this does not

mean the LCD will be out of the order. It will recover when it returns to the specified temperature range.

◆ If EastRising display area is pushed hard during operation, the display will become abnormal. However, it will return to

normal if it is turned off and then back on.

◆ Condensation on terminals can cause an electrochemical reaction disrupting the terminal circuit. Therefore, it must be

used under the relative condition of 40℃, 50% RH.

◆ When turning the power on, input each signal after the positive/negative voltage becomes stable.

7.7 Limited Warranty

449B419B446B416B443B413BUnless agreed between EastRising and customer, EastRising will replace or repair any of its LCD modules which are found

to be functionally defective when inspected in accordance with EastRising LCD acceptance standards (copies available

upon request) for a period of one year from date of shipments. Cosmetic/visual defects must be returned to EastRising

within 90 days of shipment. Confirmation of such date shall be based on freight documents. The warranty liability of

EastRising limited to repair and/or replacement on the terms set forth above. EastRising will not be responsible for any

subsequent or consequential events.

7.8 Return Policy

22B419B416BNo warranty can be granted if the precautions stated above have been disregarded. The typical examples of violations

are:

-Broken LCD glass.

-PCB eyelet damaged or modified.

-PCB conductors damaged.

-Circuit modified in any way, including addition of components.

-PCB tampered with by grinding, engraving or painting varnish.

-Soldering to or modifying the bezel in any manner.

Module repairs will be invoiced to the customer upon mutual agreement. Modules must be returned with sufficient

description of the failures or defects. Any connectors or cable installed by the customer must be removed completely

without damaging the PCB eyelet’s, conductors and terminals.




8. IMAGE STICKING HHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHH HHH

369B366B363B31B450B447B444B8.1 What is Image Sticking?

If you remain a fixed image on LCD Display for a long period of time, you may experience a phenomenon called Image

Sticking. Image Sticking - sometimes also called “image retention” or “ghosting”- is a phenomenon where a faint

outline of a previously displayed image remains visible on the screen when the image is changed. It can occur at

variable levels of intensity depending on the specific image makeup, as well as the amount of time the core image

elements are allowed to remain unchanged on the screen. In POS applications, for example, a button menu which

remains fixed, or in which the “frame” elements (core image) remain fixed and the buttons may change, may be

susceptible to image sticking. It is important to note that if the screen is used exclusively for this application, the user

may never notice this phenomenon since the screen never displays other content. `It is only when an image other than

the “retained” image is shown on the screen that this issue becomes evident. Image sticking is different that the

“burn-in” effect commonly associated with phosphor based devices.

8.2 What causes Image Sticking?

Image sticking is an intrinsic behavior of LCD displays due to the susceptibility to polarization of the interior materials

(liquid crystals) when used under static, charged conditions (continuously displaying the same image). The individual

liquid crystals in an LCD panel have unique electrical properties. Displaying a fixed pattern - such as the POS menu

described above – over prolonged periods can cause a parasitic charge build-up (polarization) within the liquid

crystals which affects the crystals’ optical properties and ultimately prevents the liquid crystal from returning to its

normal, relaxed state when the pattern is finally changed. This effect takes place at a cellular level within the LCD, and

the effect can cause charged crystal alignment at the bottom or top of a crystal cell in the “z” axis, or even crystal

migration to the edges of a cell, again based on their polarity. These conditions can cause image sticking over an

entire area, or at boundaries of distinct color change respectively. In either case, when the liquid crystals in the pixels

and sub-pixels utilized to display the static image are polarized such that they can not return fully to their “relaxed”

state upon deactivation, the result is a faint, visible, retained image on the panel upon presentation of a new, different

image. The actual rate of image retention depends on variation factors such as the specific image, how long it is

displayed unchanged, the temperature within the panel and even the specific panel brand due to manufacturing

differences amongst panel manufacturers.




8.3 How to Avoid Image Sticking?

- Try not to operate the LCD with a “fixed” image on the screen for more than 2 hours.

- If you are operating the monitor in an elevated temperature environment and with a displayed image which is

contrary to the recommendations in “For Software Developers” below, image stick can occur in as little as 30

minutes. Adjust your screen saver settings accordingly.

- Power down the unit during prolonged periods of inactivity such as the hours a store is closed or a shift during which

the piece of equipment isn’t used.

- Use a screensaver with a black or medium gray background that is automatically set to come on if the device is

inactive for more than 5-10 minutes.

- Avoid placing the monitor in poorly ventilated areas or in areas that will create excess heat around the monitor for

software developers.

- In defining the icons, buttons, or windows in the screen, try to utilize block patterns instead of distinct lines as

borders for dividing the display into distinct areas.

- If it is necessary to display a static image, try to use colors that are symmetric to the middle grey level at the

boundary of two different colors, and slightly shift the borders line once in a while.

- Try to utilize medium gray hues for those areas that will have prolonged display times or remain static as other menu

elements change.

8.4 How to Fix the Image Sticking?

Unlike the usually irreversible “burn-in” effects commonly associated with direct view phosphor display devices

such as CRTs, an image retained on an LCD display can be reversed – often to a point of total invisibility. However, the

severity of the underlying causes (as described above) of the image retained on a specific display, as well as the

variation factors (see “For Software Developers” above) under which the retained image was created, will dictate the

final level of retention reversal. One way to erase a retained image on a panel is to run the screen (monitor “on”) in

an “all black” pattern for 4-6 hours. It is also helpful to do this in an elevated temperature environment of

approximately 35º to 50ºC. Again, utilizing a dynamic screen saver with an all black background during prolonged idle

display periods is a good way to avoid image retention issues.

8.5 Is Image Sticking Covered by EastRising RMA Warranty?

Image sticking is a phenomenon inherent to LCD Display technology itself, and as such, the occurrence of this

“ghosting” effect is considered normal operation by the manufacturers of the LCD display modules which are

integrated into today’s monitor solutions. EastRising does not warrant any display against the occurrence of image

sticking. We strongly advise that you follow the operating recommendations listed above to avoid the occurrence of

this phenomenon.

That's the end of the datasheet.

Documents

ER-TFT024-3 - buydisplay.com · ER-TFT024-3 2.4”TFT LCD Display with no Touch Panel. ER-TP024-3 2.4”Resistive Touch Panel ER-TPC024-3 2.4”Capacitive Touch Panel with Controller.(Under