Upload
harva
View
65
Download
0
Embed Size (px)
DESCRIPTION
ENMAT101A Engineering Materials and Processes Associate Degree of Applied Engineering (Renewable Energy Technologies) Lecture 9 – Equilibrium diagrams. Equilibrium diagrams. EMMAT101A Engineering Materials and Processes. Equilibrium diagrams. - PowerPoint PPT Presentation
Citation preview
TAFE NSW -Technical and Further Education Commission
www.highered.tafensw.edu.au
ENMAT101A Engineering Materials and ProcessesAssociate Degree of Applied Engineering (Renewable Energy Technologies)Lecture 9 – Equilibrium diagrams
TAFE NSW -Technical and Further Education Commission
Equilibrium diagrams
EMMAT101A Engineering Materials and Processes
Reference Text Section
Higgins RA & Bolton, 2010. Materials for Engineers and Technicians, 5th ed, Butterworth Heinemann
Ch 9
Additional Readings Section
Callister, W. Jr. and Rethwisch, D., 2010, Materials Science and Engineering: An Introduction, 8th Ed, Wiley, New York.
Ch 10
TAFE NSW -Technical and Further Education Commission
Equilibrium diagrams
EMMAT101A Engineering Materials and Processes
Note: This lecture closely follows text (Higgins Ch9)
TAFE NSW -Technical and Further Education Commission
Equilibrium diagrams
EMMAT101A Engineering Materials and Processes
An equilibrium diagram (or phase diagram) is a graphical method of illustrating the relationship between the composition, temperature, and structure, or state, of any alloy in a series.
“Series” might be iron/carbon, lead/tin, copper/zinc, where the diagram is plotted over a range of percentage mixtures.
The diagram can help us to decide suitable heat-treatment processes for a particular carbon-steel. For a non-ferrous alloy system, the equilibrium diagram will often give us a pretty good indication of the structure - and hence the mechanical properties.
TAFE NSW -Technical and Further Education Commission
EMMAT101A Engineering Materials and Processes
The Iron-Carbon equilibrium diagram over a very small range of Carbon (0 to 2% by weight, or 0 to 7% by atoms)
This is as much carbon as steel can handle before it turns into cast iron, and then useless rock.
This diagram will meet you again soon (not today).
TAFE NSW -Technical and Further Education Commission
Obtaining equilibrium diagrams (Higgins 9.2)
EMMAT101A Engineering Materials and Processes
How are equilibrium diagrams obtained? Even for a simple binary alloy, some poor person had to carefully study each percentage just to plot a single dot on the curve!
There are about 70 metals, so that would mean 2415 combinations! Not quite – some don’t mix – e.g. high melting-point tungsten with very reactive caesium.
However, lots of metallic elements have been successfully alloyed with each other and with some of the non-metallic elements like carbon, silicon and boron.
There are a lot of alloys!
TAFE NSW -Technical and Further Education Commission
Melting / Boiling of Elements
EMMAT101A Engineering Materials and Processes
www.ptable.com
TAFE NSW -Technical and Further Education Commission
Lead-tin alloys (Higgins 9.2.1)
EMMAT101A Engineering Materials and Processes
TAFE NSW -Technical and Further Education Commission
Gas to Liquid. (Metal Vapour Condensing)
The temperature of a metal vapour (gas) falls until it reaches the boiling point where it starts to turn into liquid (condense).
In a liquid the atoms are randomly mixed together and are free to slide around. The atoms are held together only by weak forces of attraction at this stage, the liquid lacks cohesion and will flow.
Gas Animations: Tim Lovett 2012
EMMAT101A Engineering Materials and Processes
TAFE NSW -Technical and Further Education Commission
Latent HeatA pure metal solidifies at a fixed temperature (melting point).The liquid resists cooling below the melting point until the liquid has solidified. This requires removal of the Latent Heat. This energy is called the latent heat of fusion (solidification in this case).
Alloys (metal mixtures) can have a range of melting temperatures.
Higgins: Fig 4.1
EMMAT101A Engineering Materials and Processes
TAFE NSW -Technical and Further Education Commission
Lead-tin alloys (Higgins 9.2.1)
EMMAT101A Engineering Materials and Processes
Other ratios are tested for mushy and freezing points.They must be cooled slowly (to keep in EQUILIBRIUM)
TAFE NSW -Technical and Further Education Commission
Lead-tin alloys (Higgins 9.2.1)
EMMAT101A Engineering Materials and Processes
Plotting the data on a composition axis vs temperature.
This is the beginning of an equilibrium diagram.
TAFE NSW -Technical and Further Education Commission
Lead-tin alloys (Higgins 9.2.1)
EMMAT101A Engineering Materials and Processes
This is the whole thing for Lead and Tin.
http://www.ami.ac.uk/courses/topics/0244_tsm/index.html
TAFE NSW -Technical and Further Education Commission
Types of equilibrium diagrams (Higgins 9.3)
EMMAT101A Engineering Materials and Processes
A useful alloy must be soluble when molten, or there is no chance of any solid mixture. (E.g. Molten lead with zinc floating on top).
In the solid state the metals may be;
1. Completely soluble.2. Completely insoluble.3. Partially soluble.
To stay in equilibrium, some alloys need to be cooled extremely slowly – way too slowly for many industrial situations.
TAFE NSW -Technical and Further Education Commission
Two metals fully soluble (Higgins 9.3.1)
EMMAT101A Engineering Materials and Processes
Above the liquidus, mixture is liquid.
Below the solidus, mixture is solid.
TAFE NSW -Technical and Further Education Commission
Two metals fully soluble (Higgins 9.3.1)
EMMAT101A Engineering Materials and Processes
Follow notes in Higgins 9.3.1 in detail
TAFE NSW -Technical and Further Education Commission
Two metals completely insoluble (Higgins 9.3.2)
EMMAT101A Engineering Materials and Processes
TAFE NSW -Technical and Further Education Commission
Dendritic solidification (Higgins 4.3.1)
As the molten pure metal cools below its freezing point, crystallisation will begin. It starts out with a single unit – (e.g. BCC for Tungsten).
New atoms will join the 'seed crystal' and grow onto the structure much like a snowflake (except the metal is forming in liquid, not a cloud of droplets).
BCC Unit: Higgins Fig 4.3
Snowflake: Wikipedia
The branched crystal is called a 'dendrite‘ (Greek
for tree).
Higgins Fig 4.4
EMMAT101A Engineering Materials and Processes
TAFE NSW -Technical and Further Education Commission
Dendrite of Silver: Wikipedia
EMMAT101A Engineering Materials and Processes
TAFE NSW -Technical and Further Education Commission
Two metals completely insoluble (Higgins 9.3.2)
EMMAT101A Engineering Materials and Processes
Above the liquidus, mixture is liquid.
Below the solidus, mixture is solid.
TAFE NSW -Technical and Further Education Commission
Two metals completely insoluble (Higgins 9.3.2)
EMMAT101A Engineering Materials and Processes
Follow notes in Higgins 9.3.2 in detail
TAFE NSW -Technical and Further Education Commission
Two metals are partially soluble (Higgins 9.3.3)
EMMAT101A Engineering Materials and Processes
TAFE NSW -Technical and Further Education Commission
Two metals completely insoluble (Higgins 9.3.3)
EMMAT101A Engineering Materials and Processes
Follow notes in Higgins 9.3.3 in detail
TAFE NSW -Technical and Further Education Commission
Precipitation from a solid solution (Higgins 9.4.2)
EMMAT101A Engineering Materials and Processes
Follow notes in Higgins 9.4 in detail
At higher temperature, water can dissolve more salt.
Likewise, at higher temperature, metal A can dissolve more metal B
TAFE NSW -Technical and Further Education Commission
Precipitation from a solid solution (Higgins 9.4)
EMMAT101A Engineering Materials and Processes
Follow notes in Higgins 9.4.2 in detail
Copper solute in Aluminium (Cu/Al diagram)
Fast cooling (quenching) prevents precipitate forming. Age hardening allows precipitate to attempt to form is solid – causing lattice distortion > hindering slip > hardening the alloy. E.g. Duralumin 4%Cu.
TAFE NSW -Technical and Further Education Commission
Ternary equilibrium. (Higgins 9.5) Three metals, a 3D diagram!
EMMAT101A Engineering Materials and Processes
TAFE NSW -Technical and Further Education Commission
EMMAT101A Engineering Materials and Processes
Wikipedia: Materials properties
Online Properties Resources.
Metal Grains and processing
HandoutTeach yourself phase diagrams
http://www-g.eng.cam.ac.uk/mmg/teaching/phasediagrams/i2a.html
TAFE NSW -Technical and Further Education Commission
GLOSSARY
Phase DiagramEquilibrium DiagramLiquidus lineSolidus lineCoring or cored structureDendriticBinaryTertiarySolid phase changeEutecticPhaseEutectic phaseHypereutectoid alloyHypoeutectoid alloySolubility limitSystem
EMMAT101A Engineering Materials and Processes
TAFE NSW -Technical and Further Education Commission
QUESTIONSCallister: Ch3 (Mostly about calculating atomic packing factors - too esoteric)Moodle XML: Some questions in 10102 Classification and 10105 Steel
1. Define all the glossary terms.2. There are two names for the same thing: Phase Diagram and Equilibrium
Diagram. Both make sense. Describe what phase and equilibrium refer to.3. Why would it be difficult to make an alloy of Rhenium and Cadmium?4. Why is it important for a eutectic mixture to cool slowly during the creation of an
equilibrium diagram?5. What happens between the liquidus and solidus lines of a simple binary
equilibrium diagram with complete solubility?6. In the Cadmium-Bismuth thermal equilibrium diagram, What happens as a
mixture that crosses the BE line, the AE line, the EC line, the ED line? 7. In the lead-tin thermal equilibrium diagram, what does a and b stand for? What
is the difference between Lead, Tin, a and b? What happens as a mixture that crosses the AB line, the CB line, the BE line, the EF line?
EMMAT101A Engineering Materials and Processes