Upload
scherjeal-jangda
View
231
Download
0
Embed Size (px)
Citation preview
8/13/2019 ENTS 400 Rev5
1/62
United Energy Pakistan Ltd.
Specification For Standard
Piping
EN/TS 400
Page 1 of 62
UNITED ENERGY PAKISTAN LTD.
SPECIFICATION FOR STANDARD PIPING
EN/TS 400
Document Number: EST-301-200-IN-ENTS-00001-05
5 25/09/12 General Revision YM
4 16/11/11 General Revision YM AW MSZ
3 10/4/97 General Revision TLC
2 15/7/96 General Revision TLC
1 28/3/95 Paragraph 3.4.4 SWC
0 Issued for Use
Rev. Date Description By Checked Approved
8/13/2019 ENTS 400 Rev5
2/62
United Energy Pakistan Ltd.
Specification For Standard
Piping
EN/TS 400
Page 2 of 62
Table of Contents
1. Scope .. 1
2. Standards, Codes & References .. 1
3. Design & Fabrication .. 2
4. General .. 8
5. Materials .. 9
6. Inspection .. 9
7. Testing .. 10
Appendices
Appendix A Piping Material Specification 14
Appendix B Valve Specification . 46
Appendix C Valve Specification With Socket Weld End Connections... 60
8/13/2019 ENTS 400 Rev5
3/62
United Energy Pakistan Ltd.
Specification For Standard
Piping
EN/TS 400
Page 3 of 62
1. Scope
This specification defines the minimum requirements for the materials, fabrication, installation,inspection and testing of all piping systems to be used on vendor fabricated skids, in-house
fabricated skids and off-skid.
2. Standards, Codes and References
Applicable sections of the latest edition of the following shall form part of this specification:
2.1. American Petroleum InstituteAPI RP 1104 Welding of Pipelines & Related Facilities
API 5L Specification for Line Pipe
2.2. American Society of Mechanical EngineersASME B16.9 Butt Welded Fittings
ASME B16.5 Steel Pipe Flanges & Fittings
ASME B16.11 Screwed & Socket Weld Fittings
ASME B16.20 Ring Joint Gasket and Grooves for Steel Pipe Flanges
ASME B31.3 Chemical Plant and Petroleum Refinery Piping
ASME B31.4 Liquid Transportation systems for Hydrocarbon, Liquid Petroleum Gas,
Anhydrous Ammonia and Alcohols
ASME B31.8 Gas Transmission & Distribution Piping SystemBoiler & Pressure Vessel Code, Section VIII, Division I
Boiler & Pressure Vessel Code, Section IX
Boiler & Pressure Vessel Code, Section II
Boiler & Pressure Vessel Code, Section V
2.3. American Society for testing & MaterialsASTM A36 Steel Structure
ASTM A105 Forgings, Carbon Steel for Piping ComponentsASTM A106 Seamless Carbon Steel Pipe for High Temperature Service
ASTM A165 Electrodeposited Coatings of Cadmium on Steel
ASTM A193 Alloy Steel & Stainless Steel Bolting Material High Temperature Service
ASTM A194 Carbon & Alloy Steel Nuts for Bolting for High Pressure & High
Temperature Service
ASTM A234 Piping Fittings of Wrought Carbon Steel and Alloy Steel for Moderate and
Elevated Temperatures
MSS-SP-44 Steel Pipeline Flanges
8/13/2019 ENTS 400 Rev5
4/62
United Energy Pakistan Ltd.
Specification For Standard
Piping
EN/TS 400
Page 4 of 62
MSS-SP-75 Specification for High Test Wrought Buttweld Fittings
3. Design & Fabrication
3.1 General
3.1.1. All piping, valves and associated items shall be designed, procured, fabricatedand installed in accordance with ASME B31.3 or ASME B31.8 as appropriatefor the piping class and service designations setout in Appendices A and
B of this specification.
3.1.2. Field weld ends of pipe spools shall have a minimum of an extra six (6) inchesto assure adequate length when fitting in place.
3.1.3. Dimensional tolerances for the fabrication and installation of piping systems
shall be +/- 1/8 inch and +/-2 degrees.3.1.4. A inch 316 SS ball valve with SS plug shall be installed on the top of
piping at all high points and on the bottom at all low spots. High point ventsand low point drains shall be installed prior to hydrotesting.
3.1.5. Preparations for butt welding pipe ends having unequal wall thicknesses shallbe in accordance with the applicable ASME standard.
3.1.6. Threaded bushings shall not be used; except where required to install pressureinstruments and in plastic piping.
3.1.7. Eccentric reducers (flat side up) shall be installed in pump suction lines.
3.1.8. Ells shall be long radius unless otherwise specified.
3.1.9. Ells on instrument air lines less than 2 inch in size shall be screwed tees withplugs. Ball valves will be installed at the ends of instrument air headers and at
the end of pipe runs where piping goes vertically upwards. Drain valves will
be installed at low points. Branch connections for instrument air headers shallbe taken off the top and each branch shall be provided with a inch 316 SS
ball valve.
3.1.10. All open ended threaded connections shall have a 316 SS heavy Hex headplug installed.
3.1.11. All-thread pipe nipples shall not be used.
3.1.12. Unless specified otherwise, corrosion allowance for B31.3 piping is assumed
to be 0.05 inch.
3.2 Piping Layout
3.2.1. Sufficient clearance should be allowed between lines to permit ready accessfor repair or removal. A minimum of 1 inch shall be allowed between pipeand adjoining flanges on parallel lines. Insulation thickness must be taken into
consideration.
8/13/2019 ENTS 400 Rev5
5/62
United Energy Pakistan Ltd.
Specification For Standard
Piping
EN/TS 400
Page 5 of 62
3.2.2. The suction lines of pumps shall be as short and direst as possible, eliminatingall vapour pockets. Flexibility and support shall be provided to minimize the
load transmitted to the pump.
3.2.3. Relief valves shall be installed in a upright position and in a location
accessible from a platform or grade.3.2.4. Relief valve outlet lines in process service which are indicated by the
drawings to be routed to the flare shall slope to main flare header avoidingpockets where possible.
3.2.5. All equipment requiring frequent attention of the operating and maintenancepersonnel shall be readily accessible. Equipment such as control valves shall
preferably be grouped at main operating levels.
3.2.6. Equipment such as motor operated valves and relief valves shall be accessiblefrom platforms or grade. Platforms shall be of such extent that normalmaintenance at manways and installation of blinds will not require reaching
outside of the handrails3.2.7. Where equipment is designed to be removed for repair or replacement, the
piping shall be arranged to allow removal of the equipment without removingthe block valves adjacent to the equipment or large quantities of associated
equipment. Piping, including auxiliary piping, shall be arranged so as to not
unduly hinder in-place maintenance of the equipment.
3.2.8. A continuous piece of pipe shall be used between fittings 10 feet or less apart(no spliced pipe)
3.3 Welding
3.3.1. All pipe welding shall be in accordance with ASME B1.3, or ASME B31.8 asappropriate for the piping class and service designations setout in AppendixA of this specification.
3.3.2. The welding procedures shall be established in accordance with the applicableASME code and shall be approved by Company before fabrication may begin.
3.3.3. All welders employed by Contractor and subcontractors shall be qualified bytesting for the specific type of welding they are to perform.
3.3.4. All shop welds shall have pre-assigned weld numbers metal stamped twoinches from the edge of the weld. Weld numbers shall be assigned on a set of
piping isometric drawings with one copy to be furnished to Companysinspector. The welds shall be stamped prior to radiography.
3.3.5. Field and shop pressure piping welds made as a part of the work covered bythese specifications shall be stenciled by low stress concentration dies with a
letter or symbol which shall identify the welder. The symbol shall be locatedon a filed flat area on the weld cap. When a welder is terminated, his symbol
shall not be used again by another welder.
3.3.6. The ends of all pipe to be butt welded shall be beveled. Field cut piping shallbe formed by a beveling machine and all irregular surfaces smoothed with a
8/13/2019 ENTS 400 Rev5
6/62
United Energy Pakistan Ltd.
Specification For Standard
Piping
EN/TS 400
Page 6 of 62
hand grinder to make an acceptable joint. Any beveled edge of pipe that has
been damaged shall be restored to minimum tolerances before welding.
3.3.7. All edges or surfaces to be welded shall be cleaned to bright metal in amanner suitable to remove any oxides, scale or contamination due to flame
cutting or machining.3.3.8. All welds shall be of sound deposit with a straight line of fusion. The finished
weld contour shall be uniform with the toe or edge of the weld mergingsmoothly into the base material. Butt welds shall have a slight reinforcement
built-up gradually from the toe or edge towards the center of the weld. Filletwelds may be slightly concave on the finished surface.
3.3.9. Butt Welds shall have full penetration and complete fusion with a maximumof 1/8 inch weld metal protruding inside the pipe.
3.3.10. Back-up rings shall not be used.
3.3.11. Should lamination or split ends be discovered in the pipe, the full length
containing such defects shall be removed. No portion of such discarded jointsshall be used.
3.3.12. Any cracks, blowholes, cold lap, unusual irregularities, slag, flux or otherimpurities that appear on the surface of any weld bead shall be removed by
grinding or chipping before depositing the next successive bead.
3.3.13. All finished welds shall have any oxides and slag removed by grinding wheelor disc.
3.3.14. No welding shall be done when weather conditions would impair the qualityof the weld. Company will determine if weather conditions are not suitable for
welding.
3.3.15. All material shall be preheated to approximately 70F prior to welding. Allmaterial with the wall thickness of .750 inch or greater shall be preheated to
200 to 300F.
3.3.16. Weld joints in carbon steel be stress relieved in accordance with ANSI B31.3when the nominal pipe thickness is greater than 3/4 inch. Contractor shall
obtain Companys written approval for his stress relieving method and
procedure prior to its use. The piping shall be brought to temperature andcooled in accordance with the ASME Code, Paragraph UCS-56 of section
VIII.
3.3.17. Pipe and fittings with welding arc burns shall be replaced at Contractors
expense if deemed necessary by company.
3.4 Flanged Connections
3.4.1. Flanged bolt holes shall symmetrically straddle the piping horizontal and verticalcenterlines except where connections to equipment dictate otherwise.
3.4.2. All ring gasket connections shall be thoroughly cleaned and shall be adequatelygreased before the gasket is put in place
8/13/2019 ENTS 400 Rev5
7/62
United Energy Pakistan Ltd.
Specification For Standard
Piping
EN/TS 400
Page 7 of 62
3.4.3. Flange bolts shall be tightened evenly and sequentially to impose equal pressureon the gasket and to avoid distortion or overstressing of equipment.
3.4.4. All Flange stud bolts shall be sized as per ANSI Standard B31.5, except than 3/4shall be added to the lengths.
3.4.5. All flange hubs shall match bores, and have tensile properties comparable to thoseof the adjacent piping material.
3.4.6. Threaded flanges may be used only to match equipment and specially items.
3.5 Threaded Connections
3.5.1. Pipe threads shall be clean cut and shall be tapered in accordance with ANSIB2.1. All threads shall be thoroughly cleaned before fabrication.
3.5.2. A copper based high temperature thread lubricant shall be used for threading
piping connections in high temperature services. Teflon tape shall be used on allother threaded connections.
3.5.3. Seal welding of threaded connections shall not be permitted.
3.5.4. Fittings not covered by the code will be installed according to fittingsmanufacturers recommendations and standard industry practice. No fittings shall
be used that were not designed for the purpose.
3.5.5. All unions shall be hammer-lug with steel ground joint integral seats.
3.6 Pipe Supports
3.6.1. All pipe supports, guides, U-Bolts, clamps, nuts and anchors shall be provided byContractor as necessary to prevent sagging, stress, vibration and as specified in
drawings and specifications. Minimum size members for pipe supports shall be 2
x 2 x 1/4" angle 2 pipe or 4 wide flange beam. Dummy leg supports may bemade of 2 pipe.
3.6.2. All piping shall be sufficiently supported in a manner that will not put unduestrain on equipment.
3.6.3. When specified, spring supports shall be installed in accordance with
manufacturers recommendations with the load as noted on the drawings.Temporary, rigid supports shall be furnished when required to prevent damage to
the spring support.
3.6.4. All structural steel for pipe supports shall conform to ASTM A36 for plates andshapes and ASTM A106 Grade B or API 5L Grade B for pipe unless noted
otherwise on the drawings.
8/13/2019 ENTS 400 Rev5
8/62
United Energy Pakistan Ltd.
Specification For Standard
Piping
EN/TS 400
Page 8 of 62
3.6.5. All U-Bolts shall be fabricated in accordance with the following rod diametertable, and shall be cadmium plated. U-Bolts shall be provided with flat washers
and double nuts.
Pipe Size Rod Size
-1 1/4"
1-1/4-2 3/8
2-1/2-5 1/2
6-8 5/8
10 3/4"
12-16 7/8
3.6.6. All overhead pipe racks shall be supported by deck beams where possible or haveheader beams of equal size to the pipe rack support beam.
3.7 Insulation shall be installed where indicated on drawings.
3.8 All piping shall be painted in accordance with Specification no EN/TS-102-ProtetiveCoatings. Piping spools, pipe supports, valves, control, and other equipment items shall be
sandblasted and painted with the primer and intermediate coats prior to assembly.
4. General
4.1 Piping systems including piping, valves and fittings shall be furnished , fabricated,installed, inspected and tested in accordance with reference materials listed in Section 2.0
of this specification and as specified herein.
4.2 Mechanical flow sheets, piping assembly, and/or isometric drawings define each pipessize, service, line number, pressure class, schedule, valve identification, dimensional data
and other pertinent details of that piping system.
4.3 Information on the drawings and in specifications shall be strictly adhered to duringfabrication and installation of each piping system, unless authorized otherwise by company.
4.4 During erection of piping on skids or decks, Contractor shall ensure that vessel andequipment flanges and openings remain covered to minimize collection of trash or debris in
the equipment.
4.5 Completed, prefabricated piping spools shall be internally cleaned to remove blastingsands, weld splatter, and other debris before being used for assembly of piping systems.
Contractor shall take suitable precautions to prevent accumulation of sand, trash, or otherdebris in the piping as it is being erected.
8/13/2019 ENTS 400 Rev5
9/62
United Energy Pakistan Ltd.
Specification For Standard
Piping
EN/TS 400
Page 9 of 62
5. Materials
5.1 Materials can be of domestic (U.S) manufacture or non US manufacture, and shall befurnished in accordance with the respective piping class and service designations set out in
Appendices A and B of this specification. Substitutions will be permitted, with
Companys written approval, when specified items cannot be obtained provided the quality
of substituted materials equals or exceeds the specified materials.
5.2 Material test reports shall be provided for all pipe used in pressure services.
5.3 All O-let fittings shall be ASTM A-105 forged.
5.4 All materials shall be new, unused, and undamaged.
6. Inspection
6.1 General
6.1.1. The responsibility for quality control rests with Contractor. Company mayprovide additional inspection services at his expense and may inspect piping at
any time during its fabrication, installation, or testing to assure that materials and
workmanship are in accordance with these specifications.
6.1.2. Contractor will provide radiographic inspection.
6.1.3. Companys inspector shall be given suitable notice of scheduled inspections andtests to assure his attendance.
6.2 Visual Inspection
All welds shall receive a complete visual inspection in accordance with the applicable ANSI
code.
6.3 Radiographic Inspection
6.3.1 All piping welds shall receive 100% radiographic examination by contractor.
6.3.2 The radiographic procedure and acceptance criteria shall be in accordance with
the applicable ANSI code for 100% radiography.6.3.3 All welds found to be defective shall be repaired and reradiographed at
Contractors expense. The applicable ANSI code shall be used as a guide in
repairing defective welds.
6.3.4 Radiographic inspection shall be performed in accordance with the followingguidelines:
- Only piping butt welds will be radiographed, weld-lets and thread-o-lets will not be radiographed.
8/13/2019 ENTS 400 Rev5
10/62
United Energy Pakistan Ltd.
Specification For Standard
Piping
EN/TS 400
Page 10 of 62
- Film will be Kodak M film or approved equal, minimum 70mmwidth, three shots per weld, minimum
- Film will be shot head-on, no elliptical shots.
- Companys representative shall review and approve all radiographs.
- Contractor shall be responsible for preparing and maintaining a weldtraceability/numbering system for all piping welds. Contractor shallpre-assign weld numbers to each weld to be made and record this on a
set of piping isometrics. Weld numbers are to be stamped adjacent to
the weld on the pipe using low stress stamps. All
radiographs/reports/repairs shall reference these pre-assignednumbers. A copy of these isometrics shall be provided with a copy of
all x-ray reports to Company representative. The film and film records
shall be maintained by Contractor for a period of two years after
completion of the project.
6.4 Welding Procedures and Qualification Records
Contractor shall furnish Companys inspector with a copy of their qualified welding procedures
and welder qualification records.
7. Testing
7.1 Hydrostatic tests shall be performed by Contractor on all piping in accordance with theapplicable ANSI code and as specified herein.
7.2 All hydrostatic tests shall be witnessed by company. Three (3) days notice of test datesshall be provided.
7.3 Pressure recorders used for the test shall be of such range that the pressure to be recordedwill fall within the upper three-quarters (3/4 ths) of the recorders range. Pressure recordershall be calibrated with a dead weight tester prior to each pressure test. Calibration shall be
witnessed and certified by Company. In addition, if specified by Company, a dead weight
tester shall be installed and pressures recorded during each test.
7.4 Prior to beginning the pressure testing of the piping system, Contractor shall prepare aschedule showing each section of piping that is to be tested at one time.
7.5 Fresh water shall be used for all process piping tests. Instrument air systems shall be testedwith air. Fuel gas systems shall be tested with air or nitrogen. The use of any liquid for a
test shall have prior written approval of Company.
7.6 The water used for hydrostatic testing shall be chemically treated to prevent corrosion. Twogallons of Tretolite KW12 and 0.5 gallons of Tretolite K490 shall be used per 100 barrels
of water. These inhibitors shall be added separately and thoroughly mixed in the water.
8/13/2019 ENTS 400 Rev5
11/62
United Energy Pakistan Ltd.
Specification For Standard
Piping
EN/TS 400
Page 11 of 62
7.7 Test pressures shall be 1.5 times the maximum working pressure at 100F as given on theappropriate Piping Material specification sheet. The duration shall be a minimum of two
(2) hours.
7.8 Consideration shall be given to components in the lines which are nor rated for thespecified test pressure or which have built-in relief valve, such as instrument regulators,
etc. Contractor shall identify those components and protect them from damage which mayresult from the hydrostatic test.
7.9 All materials damaged during test shall be replaced by Contractor at no additional cost toCompany.
7.10 All leaks and defects shall be repaired and retested at no additional cost to company.
7.11 The test will be considered satisfactory after all leaks and defects have been repaired andthe full test pressure is held for the duration specified.
7.12 Following the completion of satisfactory hydrostatic tests, all piping system shall bedrained and dried. Company shall verify drying completion.
7.13 Contractor shall furnish certification and copy of recording chart for the test of each pipingsystem unit. Recording chart shall be signed by companys inspector as witness and shall
contain date of test and appropriate identification of section tested.
8/13/2019 ENTS 400 Rev5
12/62
United Energy Pakistan Ltd.
Specification For Standard
Piping
EN/TS 400
Page 12 of 62
8/13/2019 ENTS 400 Rev5
13/62
United Energy Pakistan Ltd.
Specification For Standard
Piping
EN/TS 400
Page 13 of 62
ITEM SIZE DESCRIPTION SPEC CONNECTION
Pipe Less than 2" Smls Sch. 80 A106 SW or NPT
Pipe 2 Smls Sch. 80 A106 BW or SW
Pipe Greater than 2 Smls A106 or BW
API 5L
Nipples & Less than 2 Smls Sch. 80 A106 SW or NPTSwages
Nipples & 2 Smls Sch. 80 A106 BW or SWSwages
Flanges Less than 2 RF or RTJ ASTM A105, SWANSI B16.5
Flanges 2 RF or RTJ ASTM A105, WN or SW
ANSI B16.5
Flanges Greater than 2 RF or RTJ ASTM A105, WN
ANSI B16.5
Fittings Less than 2 3000#FS ASTM A234
WPB, ANSI B16.11 SW or NPT
Fittings 2 3000#FS ANSI B16.11 or SW or BW
B16.9
Fittings Greater than 2 FS ANSI B16.9 BW
Unions Less than 2 3000#FS MSS-SP-83 SW or BW
Unions 2 3000#FS MSS-SP-83 BW or SW
Couplings 2 and less 3000#FS, NPT ANSI B16.11 Instrument
Connections
Plugs 2 and less 3000#FS, NPT ANSI B16.11
8/13/2019 ENTS 400 Rev5
14/62
United Energy Pakistan Ltd.
Specification For Standard
Piping
EN/TS 400
Page 14 of 62
APPENDIX A
PIPING MATERIAL SPECIFICATION
8/13/2019 ENTS 400 Rev5
15/62
United Energy Pakistan Ltd.
Specification For Standard
Piping
EN/TS 400
Page 15 of 62
Appendix A
The following piping specifications and service designations are used in the attached material specification sheets. Valve specificationsreferenced herein are included in Appendix B.
CLASS
A-ASME 150, Process, Utilities, Air, Water, Drains
A1 - Hydrocarbons, ASME 150, B31.3
A2 - Hydrocarbons, ASME 150, B31.4
A3 - Gas, ASME 150, B31.8
A4 - Instrument Air, Utility Air & Water, ASME 150, B31.3
A5 - Potable Water, ASME 150, B31.3
A6 - Fire water pipe, Plastic, 150 lb. CWP, ASME B31.3
A7 - Fire water pipe, Steel, ASME 150, B31.3
B-ASME 300, Process, Air
B1 - Hydrocarbons, ASME 300, B31.3
B2 - Hydrocarbons, ASME 300, B31.4B3 - Gas, ASME 300, B31.3
B4 - Gas, ASME 300, B31.8
B5 - Starting Air, ASME 300, B31.3
C-ASME 600, Process
C1 - Hydrocarbons, ASME 600, B31.3
C2 - Hydrocarbons, ASME 600, B31.4
C3 - Gas, ASME 600, B31.3
C4 - Gas, ASME 600, B31.8
C5 - High Temperature Service, ASME 600, B31.3
D-ASME 900, Process
D1 - Hydrocarbons, ASME 900, B31.3
D2 - Hydrocarbons, ASME 900, B31.4
D3 - Gas, ASME 900, B31.3
D4 - Gas, ASME 900, B31.8
E-ASME 1500, Process
E1 - Hydrocarbons, ASME 1500, B31.3
E2 - Hydrocarbons, ASME 1500, B31.4
E3 - Gas, ASME 1500, B31.3
E4 - Gas, ASME 1500, B31.8
F-ASME 2500, Process
F1 - Hydrocarbons, ASME 2500, B31.3
F2 - Hydrocarbons, ASME 2500, B31.4
F3 - Gas, ASME 2500, B31.3
F4 - Gas, ASME 2500, B31.8
G-API-5000, Process
G1 - Hydrocarbons, API 5000 lb, B31.3
G2 - Hydrocarbons, API 5000 lb, B31.4
G3 - Gas, API 5000 lb, B31.3
G4 - Gas, API 5000 lb, B31.8
8/13/2019 ENTS 400 Rev5
16/62
United Energy Pakistan Ltd.
Specification For Standard
Piping
EN/TS 400
Page 16 of 62
SERVICE DESIGNATIONS
CH - Chemical
DR - DrainFG - Fuel Gas
FL - Flare
FO - Fuel Oil
FW - Fire Water
GL - Glycol
H - Halon
HM - Heat Media
HO - Hydraulic Oil
IA - Instrument Air
IG - Instrument Gas
JW - Jacket Water
LHW - Liquid Hydrocarbon & Water
LO - Lube Oil
M - Miscellaneous
OW - Oily Water
P - Process
PS - Process Sewer
PW - Potable Water
R - Relief
S - Sewage
SA - Starting Air
SG - Start Gas
UA - Utility Air
UG - Utility Gas
UW - Utility Water (Sanitary Water)
V - VentW - Raw Water
WP - Salt Water
WS - Well Stream
8/13/2019 ENTS 400 Rev5
17/62
United Energy Pakistan Ltd.
Specification For Standard
Piping
EN/TS 400
Page 17 of 62
EN/TS-400
Appendix "A"
Rating:
ASME 150 lb, R.F.Design:
ANSI/ASME B31.3Service:
IG, M, UW, UG, IA, UA, PW, FW,
FO, FG, FL, P, LHW, R, V
PIPING MATERIAL
SPECIFICATION SHEET
CLASS A1, A4, A5, A7DESIGN
Max. Press. Max Temp. Limited By
285 PSIG 100 F Flanges272 PSIG 150 F Valves
245 PSIG 250 F Valves
Hydrotest Pressure:
425 psig @ 100
DegF
SIZE 1/2 3/4 1 1 1/2 2 3 4 6 8 10 12
PIPE Sch. 80 (2) Sch. 40 (5)
JOINTCONST.
SW, T &C, orflanged (1) Buttweld and flanged.
FITTINGS
3000lb. F.S, SW or Scr'dA-105 (2) A-234 WPB SMLS, buttweld, schedule to match pipe
FLANGES
ANSI 150 lbs. R.F. SW or
scr'd (1)(2)
ASTM A-105
ANSI 150 lb.R.F.W.N (7)
ASTM A-105 or MSS-SP-44,
RFWN
Class 150
UNIONS 3000 lb. F.S.G.J. (2) Use flanges All unions A-105
PLUG
solid hex
head
Bull
plugs
THR'D NIPP.
& SWAGES
Sch. XXS A-106 B
SMLS
GATE
API 602 Class 800 gate valve with SW or
Threaded ends
BALL
VBT-601
VBT-601 FB
VBF-151
VBF-151 FB VBF-152. VBF-152 FB
PLUGS
CHECK
VCT-601 (6) or API 602 Class 800 valve withSW ends VCF-151
GLOBE
VOT-601 or API-602 Class 800 valve with SW
ends VOF-151
NEEDLE (4)
GAGE
VNT-2505
VNT-2506
V
A
L
V
E
S BUTTER-
FLY VBFF-151 (3)
BOLTING Studs: A-193-B7 Nuts: A-194-2H: all cadmium plated
GASKETS 1/8" thick 304 S.S. Flexitallic "CG" or equal
NOTES
1. Use only to match equipment and special items.
2. Material shall be hot dip galvanized for instrument air, utility air, potable water, and firewater services.
3. Use with instrument air, utility air, potable water, and firewater services.
4. For 1/2" use VNT-2501 or VNT-2504. For 3/4" use VNT-2503 or VNT-2505.5. Wall thickness to be determined by pressure and services, but not less than 0.25" W.T.
6. VCT-151WP acceptable for potable water service.7. Victaulic Style 99 plain end pipe coupling may be used where indicated on drawings.
G.J= Ground joint (seat is grinded)F.S= Forged Steel.
8: Refer to Appendix-C for valve specifications with socket-weld end connections
8/13/2019 ENTS 400 Rev5
18/62
United Energy Pakistan Ltd.
Specification For Standard
Piping
EN/TS 400
Page 18 of 62
EN/TS-400
Appendix "A"
Rating:ANSI 150 lb, R.F.
Design:
ANSI/ASME B31.4,
B31.8 (6)Service:
FO, M, DR, P, LHW, FG
PIPING MATERIAL
SPECIFICATION SHEETCLASS A2, A3
DESIGN
Max. Press. Max Temp. Limited By
285 PSIG 100 F Flanges272 PSIG 150 F Valves
245 PSIG 250 F Valves
Hydrotest Pressure:
356 psig @ 100 DegF
SIZE 1/2 3/4 1 1 1/2 2 3 4 6 8 10 12
PIPE
SMLS A-53-B, A-106-B,
API 5L-B, Sch. 80 (2) Sch 40 (5)
JOINT
CONST.
SW, T &C, or
flanged (1) Buttweld and flanged.
FITTINGS
3000lb. F.S, SW orA-105 (2) A-234 WPB SMLS, buttweld, schedule to match pipe
FLANGES
ANSI 150 lbs. R.F., SW or
scr'd (1)(2)
ASTM A-105
ANSI 150 lb. R.F.W.N (3)
ASTM A-105 RFWN
Class 150
UNIONS 3000 lb. F.S.G.J. (2) Use flanges All unions A-105
PLUGS
solid hexhead
Bullplugs
THR'D NIPP.& SWAGES Sch. XXS A-106 BSMLS
GATE
API 602 Class 800 gate
valve with SW or Threaded
ends
BALL
VBT-601
VBT-601 FB
VBF-151
VBF-151 FB VBF-152. VBF-152 FB
PLUG
CHECK
VCT-601 or API 602 Class
800 valve with SW ends VCF-151
GLOBE
VOT-601 or API-602 Class
800 valve with SW ends VOF-151
NEEDLE (4)
GAGE
VNT-2505 or
VNT-2506
V
A
L
V
E
S
BUTTER-FLY
BOLTING Studs: A-193-B7 Nuts: A-194-2H: all cadmium plated
GASKETS 1/8" thick 304 S.S. Flexitallic "CG" or equal
NOTES
1. Use only to match equipment and special items.
2. Material shall be hot dip galvanized for instrument air, utility air, potable water, and firewater services.3. Victaulic Style 99 plain end pipe coupling may be used where indicated on drawings.
4. For 1/2" use VNT-2501 or VNT-2504. For 3/4" use VNT-2503 or VNT-2505.5. Wall thickness to be determined by pressure and services, but not less than 0.25" W.T. 2 mm C.A. shall be considered while calculating pipe W.T.
6. A design factor of 0.6 and grade B material have been used to determine wall thickness under B31.8.
Higher strength material may be used where appropriate.FS = Forged Steel.GJ = Ground Joint
7. 2mm CA is included as per regulatory requirements.
8: Refer to Appendix-C for valve specifications with socket-weld end connections
.
8/13/2019 ENTS 400 Rev5
19/62
United Energy Pakistan Ltd.
Specification For Standard
Piping
EN/TS 400
Page 19 of 62
EN/TS-400
Appendix "A"
Rating:
ANSI 150 lb, F.F.
Design:ANSI/ASME B31.3
Service:FW
PIPING MATERIAL
SPECIFICATION SHEET
CLASS A6DESIGN
Max. Press. Max Temp. Limited By
150 PSIG 100 F FittingsHydrotest Pressure:356 psig @ 100 DegF
SIZE 1/2 3/4 1 1 1/2 2 3 4 6 8 10 12 16 20
PIPE
Sch. 80 CPVCASTM F-441 0.14 0.18 0.19 0.241 .298 0.351
Filament wound epoxy resinBondstrand series 2000-M
JOINT
CONST.
CPVC solvent
cement (1) Bell and spigot
FITTINGS
Sch. 80 socket
type CPVC (2) Bondstrand 2000-M bell and spigot (3)
FLANGES
150 lb. F.F. CPVCsocket type Bondstrand 2000-M filament wound 150 # F.F
UNIONS CPVC socket ends Use flanges
PLUG
solid hex
head
Bull
plugs
THR'D NIPP.
& SWAGES
Sch.80 CPVC
(4)GATE
BALL VBT-601
PLUGS
CHECK VCT-151 VCF-151
GLOBE
NEEDLE (5)
GAGE
VNT-2505
VNT-2506
V
A
L
V
E
SBUTTER-
FLY VBFF-151
A-307 cap screws; A 194-2H nuts; plain washers; all cadmium platedBOLTING Studs: Nuts:
GASKETS 1/8" thick full face ethylene propylene rubber
NOTES1. CPVC solvent cement in accordance with ASTM F-493.
2. CPVC fittings in accordance with ASTM F-439.
3. Epoxy bonded joints in accordance with manufacturer's recommendations.
4. Use teflon tape thread sealant.5. For 1/2" use VNT-2501 or VNT-2504. For 3/4" use VNT-2503 or VNT-2505.
8/13/2019 ENTS 400 Rev5
20/62
United Energy Pakistan Ltd.
Specification For Standard
Piping
EN/TS 400
Page 20 of 62
EN/TS-400
Appendix "A"
Rating:ANSI 300 lb, R.F.
Design:ANSI/ASME B31.3
Service:
P, LHW, M, FG, SA
PIPING MATERIAL
SPECIFICATION SHEET
CLASS B1, B3, B5
DESIGN
Max. Press. Max Temp. Limited By
740 PSIG 100 F Valves/ Flanges680 PSIG 200 F Valves / Flanges
665 PSIG 250 F Valves / Flanges Hydrotest Pressure:
1110 psig @ 100 DegF
SIZE 1/2 3/4 1 1 1/2 2 3 4 6 8 10 12
PIPE Sch. 80 Sch. 40
JOINTCONST.
SW, T &C, orflanged (1) Buttweld and flanged.
FITTINGS
3000lb. F.S, SWA-105 A-234 WPB SMLS, buttweld, schedule to match pipe
FLANGES
ANSI 300 lbs. R.F., SW or
scr'd (1)
ASTM A-105
ANSI 300 lb.R.F.W.N
ASTM A-105, RFWN
Classs 300
UNIONS 3000 lb. F.S.G.J. Use flanges All unions A-105
PLUGS
solid hex
head
Bull
plugs
THR'D NIPP.
& SWAGES
Sch. XXS A-106 B
SMLS
GATE
API 602 Class 800 gate
valve with SW or Threaded
ends
BALL
VBT-601
VBT-601 FB
VBF-301
VBF-301 FB VBF-302. VBF-302 FB
PLUGS
CHECK
VCT-601, or API 602Class 800 valve with SW
ends VCF-301
GLOBE
VOT-601, or API-602
Class 800 valve with SW
ends VOF-301
NEEDLE (2)
GAGEVNT-2505VNT-2506
V
A
L
V
E
S
BUTTER-FLY
BOLTING Studs: A-193-B7 Nuts: A-194-2H: all cadmium plated
GASKETS 1/8" thick 304 S.S. Flexitallic "CG" or equal
NOTES
1. Use only to match equipment and special items.
2. For 1/2" use VNT-2501 or VNT-2504. For 3/4" use VNT-2503 or VNT-2505.3: Refer to Appendix-C for valve specifications with socket-weld end connections
8/13/2019 ENTS 400 Rev5
21/62
United Energy Pakistan Ltd.
Specification For Standard
Piping
EN/TS 400
Page 21 of 62
EN/TS-400
Appendix "A"
Rating:ANSI 300 lb, R.F.
Design:
ANSI/ASME B31.4,B31.8 (4)
Service:
P, LHW, M, FG
PIPING MATERIAL
SPECIFICATION SHEET
CLASS B2, B4
DESIGN
Max. Press. Max Temp. Limited By
740 PSIG 100 F Valves / Flanges680 PSIG 200 F Valves / Flanges
665 PSIG 250 F Valves / Flanges Hydrotest Pressure:925 psig @ 100 DegF
SIZE 1/2 3/4 1 1 1/2 2 3 4 6 8 10 12
PIPE (5)
SMLS, A-53-B, A-106-B,API 5L-B, Sch. 80
SMLS, A-53-B, A-106-B, API 5L-BSch. 40 (3)
JOINT
CONST.
SW, T &C, or
flanged (1) Buttweld and flanged.
FITTINGS
3000lb. F.S, SW
A-105 A-234 WPB SMLS, buttweld, schedule to match pipe
FLANGES
ANSI 300 lbs. R.F., SW or
scr'd (1)
ASTM A-105
ANSI 300 lb.R.F.W.N
ASTM A-105 RFWN
Class 300
UNIONS 3000 lb. F.S.G.J. Use flanges All unions A-105
PLUGS
solid hexhead
Bullplugs
THR'D NIPP.& SWAGES
Sch. XXS A-106 BSMLS
GATE
API 602 Class 800 gate
valve with SW or Threaded
ends
BALL
VBT-601
VBT-601 FB
VBF-301
VBF-301 FB VBF-302. VBF-302 FB
PLUGS
CHECK
VCT-601, or API 602
Class 800 valve with SW
ends VCF-301
GLOBE
VOT-601, or API-602
Class 800 valve with SW
ends VOF-301
NEEDLE (2)
GAGE
VNT-2505
VNT-2506
V
A
L
V
E
S
BUTTER-
FLY
BOLTING Studs: A-193-B7 Nuts: A-194-2H: all cadmium plated
GASKETS 1/8" thick 304 S.S. Flexitallic "CG" or equal
NOTES
1. Use only to match equipment and special items.
2. For 1/2" use VNT-2501 or VNT-2504. For 3/4" use VNT-2503 or VNT-2505.3. Wall thickness to be determined by pressure and services, but not less than 0.25" W.T.
4. A design factor of 0.6 and grade B material have been used to determine wall thickness under B31.8.Higher strength material may be used where appropriate.
5: Pipe de-rating starts after 250 Deg F6: Refer to Appendix-C for valve specifications with socket-weld end connections
8/13/2019 ENTS 400 Rev5
22/62
8/13/2019 ENTS 400 Rev5
23/62
United Energy Pakistan Ltd.
Specification For Standard
Piping
EN/TS 400
Page 23 of 62
EN/TS-400
Appendix "A"
Rating:
ANSI 600 lb. RF
Design:
ANSI/ASME B31.4
Service:
P, LHW, DR
PIPING MATERIAL
SPECIFICATION SHEET
CLASS C2
DESIGN
Max. Press. Max Temp. Limited By
1480 PSIG 100 F Flanges1415 PSIG 150 F Flanges/Valves
1360 PSIG 200 F Flanges/ValvesHydrotest Pressure:
1850 psig @ 100
DegF
SIZE 1/2 3/4 1 1 1/2 2 3 4 6 8 10 12
PIPESMLS, A-53-B, A-106-B, API 5L-BSch. 80
Sch.40 Sch.60 (3)
SMLS or ERW. A-
53-B, A-106-B, API5L-B
JOINT CONST. SW, T &C or flanged (1) Buttweld and flanged.
FITTINGS 6000lb. F.S A-105 A-234 WPB SMLS, buttweld, schedule to match pipe
FLANGESANSI 600 lbs. RTFscr'd (1)
ASTM A-105ANSI 600 lb. RF.W.N
ASTM A-105 or MSS-SP-44, RTJ, WNClass 600
UNIONS 6000 lb. F.S.G.J. Use flanges All unions A-105
PLUGSsolid hexhead
Bullplugs
THR'D NIPP.
& SWAGES
Sch. XXS A-106 B
SMLSGATE
BALL
VBT-601
VBT-601 FB
VBF-601
VBF-601 FB VBF-602. VBF-602 FB
PLUGS
CHECK VCT-601 VCF-601
GLOBE VOT-601 VOF-601
NEEDLE (2)
GAGE
VNT-2505
VNT-2506
V
A
L
V
E
SBUTTER-
FLY
BOLTING Studs: A-193-B7 Nuts: A-194-2H: all cadmium plated
GASKETS 1/8" thick 304 S.S Flexitallic "CG" or equal
NOTES
1. Use only to match equipment and special items.
2. For 1/2" use VNT-2501 or VNT-2504. For 3/4" use VNT-2503 or VNT-2505.
3. Calculated for grade B material. Higher strength material may be used where appropriate.
4: Refer to Appendix-C for valve specifications with socket-weld end connections
8/13/2019 ENTS 400 Rev5
24/62
United Energy Pakistan Ltd.
Specification For Standard
Piping
EN/TS 400
Page 24 of 62
EN/TS-400
Appendix "A"
Rating:
ANSI 600 lb, R.F.Design:
ANSI/ASME B31.8 (5)
Service:P
PIPING MATERIAL
SPECIFICATION SHEET
CLASS C4DESIGN
Max. Press. Max Temp. Limited By
1480 PSIG 100 F Flanges
1414 PSIG 150 F Flanges / Valves
1360 PSIG 200 F Flanges / Valves Hydrotest Pressure:
1850 psig @ 100 DegF
SIZE 1/2 3/4 1 1 1/2 2 3 4 6 8 10 12
PIPE (6)
SMLS, A-53-B, A-106-B,
API 5L-B,
SMLS, A-53-B, A-106-B,API 5L-B SMLS or ERW (4), A-53-B, A-106-B, API 5L-B.
SCHEDULE 80 40 40 80 60 60 60
JOINT
CONST.
SW, T &C, or
flanged (1) Buttweld and flanged.
FITTINGS
6000lb. F.S, SW
A-105 (2) A-234 WPB SMLS, buttweld, schedule to match pipe
FLANGES
ANSI 600 lbs. R.F., SW or
scr'd (1)
ASTM A-105
ANSI 600 lb.R.F.W.N
ASTM A-105 RFWN
Class 600UNIONS 6000 lb. F.S.G.J. Use flanges All unions A-105
PLUGS
solid hexhead
Bullplugs
THR'D NIPP.& SWAGES
Sch. XXS A-106 BSMLS
GATE
API 602 Class 800 gate
valve with SW or Threadedends
BALL
VBT-601
VBT-601 FB
VBF-601
VBF-601 FB VBF-602. VBF-602 FB
PLUGS
CHECK
VCT-601, or API 602 Class
800 valve with SW ends VCF-601
GLOBE
VOT-601, or API-602 Class
800 valve with SW ends VOF-601
NEEDLE (3)
GAGE
VNT-2505
VNT-2506
V
A
L
V
E
S
BUTTER-
FLY
BOLTING Studs: A-193-B7 Nuts: A-194-2H: all cadmium plated
GASKETS 1/8" thick 304 S.S. Flexitallic "CG" or equal
NOTES
1. Use only to match equipment and special items.2. A design factor of 0.6 and grade B material have been used to determine wall thickness under B31.8.
Higher strength material may be used where appropriate.3. For 1/2" use VNT-2501 or VNT-2504. For 3/4" use VNT-2503 or VNT-2505.
4: ERW pipe can be used for 10-inch and above piping. However, it shall NOT be used for Gas Service and H2S service.
5: B31.8 shall be used for all Liquid or Gas dominated services for wellheads, artificial lift piping, flowlines and any piping outside the main facility
6: Pipe de-rating starts after a temperature of 250 DegF.7: Refer to Appendix-C for valve specifications with socket-weld end connections
8/13/2019 ENTS 400 Rev5
25/62
United Energy Pakistan Ltd.
Specification For Standard
Piping
EN/TS 400
Page 25 of 62
EN/TS-400
Appendix "A"
Rating:ANSI 600 lb, R.F.
Design:
ANSI/ASME B31.8 (5)
Service:
P
PIPING MATERIAL
SPECIFICATION SHEET
CLASS C4 FLOWLINE CONSTRUCTION
DESIGN
Max. Press. Max Temp. Limited By
1480 PSIG 250 F Flanges1414 PSIG 150 F Valves
1360 PSIG 200 F Valves Hydrotest Pressure:
1850 psig @ 100 DegF
SIZE 2 3 4 6 8 10 12
PIPE (6) API 5L X-46 API 5L X-46 (4)
SCHEDULE80 40 40 40 60 60 80
THICKNESS 0.218 0.25 0.28 0.344 0.438 XS
JOINT
CONST. Buttweld and flanged.
FITTINGS A-234 WPB SMLS, buttweld, schedule to match pipe
FLANGES
MSS-SP-44
F46 Class 600 lb.R.F.W.N
MSS-SP-44
F46 600 lb.R.F.W.N
UNIONS Use flanges
PLUGS N/ATHR'D NIPP.& SWAGES N/A
GATE
BALL
VBF-601
VBF-601 FB VBF-602. VBF-602 FB
PLUGS
CHECK VCF-601
GLOBE VOF-601
NEEDLE
GAGE
V
A
L
V
E
S BUTTER-
FLY
BOLTING Studs: A-193-B7 Nuts: A-194-2H: all cadmium plated
GASKETS 1/8" thick 304 S.S. Flexitallic "CG" or equal
NOTES1. Use only to match equipment and special items.
2. A design factor of 0.6 and grade B material have been used to determine wall thickness under B31.8.
Higher strength material may be used where appropriate.
3. For 1/2" use VNT-2501 or VNT-2504. For 3/4" use VNT-2503 or VNT-2505.4: ERW pipe can be used for 10-inch and above piping. However, it shall NOT be used for Gas Service and H2S service.
5: B31.8 shall be used for all Liquid or Gas dominated services for wellheads, artificial lift piping, flowlines and any piping outside the mainfacility
6: Pipe de-rating starts after a temperature of 250 DegF.7: Refer to Appendix-C for valve specifications with socket-weld end connections
8/13/2019 ENTS 400 Rev5
26/62
United Energy Pakistan Ltd.
Specification For Standard
Piping
EN/TS 400
Page 26 of 62
EN/TS-400
Appendix "A"
Rating:
ANSI 900 lb. RTJ
Design:ANSI/ASME B31.3
Service:FL, P, LHW, R, V
PIPING MATERIAL
SPECIFICATION SHEETCLASS D1, D3
DESIGN
Max. Press. Max Temp. Limited By
2220 PSIG 100 F Valves / Flanges
2122 PSIG 150 F Valves / Flanges
2035 PSIG 200 F Valves / FlangesHydrotest Pressure:
3330 psig @ 100 DegF
SIZE 1/2 3/4 1 1 1/2 2 3 4 6 8 10 12
PIPE (2) (4) Sch. 80 120 Sch. 100
All pipe sizes: SMLS, A-53-
B,
A-106-B, API 5L-B
JOINT
CONST.
SW, T &C (2)or
flanged (1) Buttweld and flanged.
FITTINGS
6000lb. F.S, SWA-105 A-234 WPB SMLS, buttweld, schedule to match pipe
FLANGES
ANSI 900 lbs. RTJ., SWor scr'd (1)
ASTM A-105ANSI 900 lb. RTJ.W.N
ASTM A-105, RTJ, WNClass 900
UNIONS 6000 lb. F.S.G.J. Use flanges All unions A-105
PLUGS
solid hex
head
Bull
plugs
THR'D NIPP.
& SWAGES
Sch. XXS A-106 B
SMLS
GATE
API 602 Class 1500 gatevalve with SW or
Threaded ends
BALLVBT-1501VBT-1501 FB
VBF-901
VBF-901
FB VBF-902. VBF-902 FB
PLUGS
CHECK
VCT-1501, or API 602
Class 1500 valve with SWends VCF-901
GLOBE
VOT-1501, or API 602
Class 1500 valve with SWends VOF-901
NEEDLE (3)
GAGE
VNT-2505
VNT-2506
V
A
L
V
E
S
BUTTER-FLY
BOLTING Studs: A-193-B7 Nuts: A-194-2H: all cadmium plated
GASKETS 316 S.S. Type "R" ring joint gasket, oval section
NOTES
1: Use only to match equipment and special items.
2: Welds in piping 6" and larger shall be stress relieved.3: For 1/2" use VNT-2501 or VNT-2504. For 3/4" use VNT-2503 or VNT-2505.
4: Minimum wall thicknesses shown are based on 0.05" corrosion allowance and 100 Deg F design temperature and 12.5% tolerance factor
5: Refer to Appendix-C for valve specifications with socket-weld end connections
8/13/2019 ENTS 400 Rev5
27/62
United Energy Pakistan Ltd.
Specification For Standard
Piping
EN/TS 400
Page 27 of 62
EN/TS-400
Appendix "A"
Rating:ANSI 900 lb. RTJ
Design:ANSI/ASME B31.4
Service:P, LHW, DR
PIPING MATERIAL
SPECIFICATION SHEETCLASS D2
DESIGN
Max. Press. Max Temp. Limited By
2220 PSIG 100 F Flanges / Valves2122 PSIG 150 F Flanges / Valves
2035 PSIG 200 F Flanges / Valves Hydrotest Pressure:2775 psig @ 100 DegF
SIZE 1/2 3/4 1 1 1/2 2 3 4 6 8 (5) 10 12
PIPESMLS, A-53-B, A-106-B, API 5L-B
SMLS A-53-B, A-106-B, API
5L-B
SMLS or ERW A-53-B, A-106-B,
API 5L-B
SCHEDULE80 80 100
JOINTCONST.
SW, T &C orflanged (1) Buttweld and flanged.
FITTINGS
6000lb. F.S
A-105 A-234 WPB SMLS, buttweld, schedule to match pipe
FLANGES
ANSI 900 lbs. RTJ.
scr'd (1)
ASTM A-105
ANSI 900 lb. RTJ.W.N
ASTM A-105 or MSS-SP-44, RTJ, WN
Class 900
UNIONS 6000 lb. F.S.G.J. Use flanges All unions A-105
PLUGS
solid hex
head
Bull
plugsTHR'D NIPP.& SWAGES
Sch. XXS A-106 BSMLS
GATE
BALL
VBT-1501
VBT-1501 FB
VBF-901
VBF-901 FB VBF-902. VBF-902 FB
PLUGS
CHECK VCT-1501 VCF-901
GLOBE VOT-1501 VOF-901
NEEDLE (3)
GAGE
VNT-2505
VNT-2506
V
A
L
V
E
SBUTTER-
FLY
BOLTING Studs: A-193-B7 Nuts: A-194-2H: all cadmium plated
GASKETS 316 S.S. Type "R" ring joint gasket, oval section
NOTES
1. Use only to match equipment and special items.2. Welds in piping 10" and larger shall be stress relieved.
3. For 1/2" use VNT-2501 or VNT-2504. For 3/4" use VNT-2503 or VNT-2505.4. Wall thickness for sizes 3" and larer were calculated for grade B material. Higher strength material may be used where appropriate.
5: Available corrosion allowance is 1.84 mm instead of 2mm
6: Refer to Appendix-C for valve specifications with socket-weld end connections
.
8/13/2019 ENTS 400 Rev5
28/62
United Energy Pakistan Ltd.
Specification For Standard
Piping
EN/TS 400
Page 28 of 62
EN/TS-400
Appendix "A"
Rating:
ANSI 900 lb. RTJ
Design:
ANSI/ASME B31.8 (6)
Service:P
PIPING MATERIAL
SPECIFICATION SHEET
CLASS D4DESIGN
Max. Press. Max Temp. Limited By2220 PSIG 100 F Flanges / Valves
2122 PSIG 150 F Flanges / Valves2035 PSIG 200 F Flanges / Valves Hydrotest Pressure:2775 psig @ 100 DegF
SIZE 1/2 3/4 1 1 1/2 2 3 4 6 8 10 12
PIPE (7)
SMLS, A-53-B, A-106-B, API 5L-BSMLS A-53-B,
A-106-B, API
5L-B (3)
SMLS or ERW(5) A-53-B, A-106-B (3)
SCHEDULE 80 80 100
JOINT
CONST.
SW, T &C or
flanged (1) Buttweld and flanged.
FITTINGS
6000lb. F.S, SW
A-105 A-234 WPB SMLS, buttweld, schedule to match pipe
FLANGES
ANSI 900 lb. RTJ., SW or
scr'd (2)
ASTM A-105
ASME 900 lb. RTJ.W.N ASTM A-105 ASME 900 RTJ WN
UNIONS 6000 lb. F.S.G.J. Use flanges All unions A-105
PLUGS
solid hexhead
Bullplugs
THR'D NIPP.
& SWAGES
Sch. XXS A-106 B
SMLS
GATE
API 602 Class 1500 gate
valve with SW or Threaded
ends
BALL
VBT-1501
VBT-1501 FB
VBF-901
VBF-901 FB VBF-902. VBF-902 FB
PLUGS
CHECK
VCT-1501, or API 602
Class 1500 valve with SWends VCF-901
GLOBE
VOT-1501, or API 602
Class 1500 valve with SWends VOF-901
NEEDLE
GAGE
VNT-2505
VNT-2506
V
A
L
V
E
S
BUTTER-
FLY
BOLTING Studs: A-193-B7 Nuts: A-194-2H: all cadmium plated
GASKETS 316 S.S. Type "R" ring joint gasket, oval section
NOTES
1. Use only to match equipment and special items.
2. Welds in piping 10" and larger shall be stress relieved.
3. A design factor of 0.60 and grade B material have been used to determine the wall thickness. Higherstrength material may be used where appropriate.
4. For 1/2" use VNT-2501 or VNT-2504. For 3/4" use VNT-2503 or VNT-2505.
5: ERW pipe can be used for 10-inch and above piping. However, it shall NOT be used for Gas Service and H2S service.6: B31.8 shall be used for all Liquid or Gas dominated services for wellheads, artificial lift piping, flowlines and any piping outside the main facility
7: Pipe de-rating starts after a temperature of 250 DegF.
8: Refer to Appendix-C for valve specifications with socket-weld end connections
8/13/2019 ENTS 400 Rev5
29/62
United Energy Pakistan Ltd.
Specification For Standard
Piping
EN/TS 400
Page 29 of 62
EN/TS-400
Appendix "A"
Rating:ANSI 900 lb,RTJ
Design:ANSI/ASME B31.8 (6)
Service:
P
PIPING MATERIAL
SPECIFICATION SHEETCLASS D4 - FLOWLINE CONSTRUCTION
DESIGN
Max. Press. Max Temp. Limited By
2220 PSIG 100 F Valves2122 PSIG 150 F Valves
2035 PSIG 200 F Valves Hydrotest Pressure:2775 psig @ 100 DegF
SIZE 2 3 4 6 8 10 12
PIPE (7) API 5L X-46 API 5L X-46 (5)
SCHEDULE 80 80 80 80 80 80 80
THICKNESS 0.218 0.25 0.282 0.375 0.5 0.594 0.688
JOINTCONST. Buttweld and flanged.
FITTINGS A-234 WPB SMLS, buttweld, schedule to match pipe
FLANGES
MSS-SP-44
F46 Class 900 lb.RTJ .W.N
MSS-SP-44
F46 900 lb.RTJ W.N
UNIONS Use flanges
PLUGS N/A
THR'D NIPP.
& SWAGES N/A
GATE
BALL
VBF-901
VBF-901 FB VBF-902. VBF-902 FB
PLUGS
CHECK VCF-901
GLOBE VOF-901
NEEDLE
GAGE
V
A
L
V
E
S BUTTER-
FLY
BOLTING Studs: A-193-B7 Nuts: A-194-2H: all cadmium plated
GASKETS 316 S.S. Type "R" ring joint gasket, oval section
NOTES1. Use only to match equipment and special items.
2: Welds in piping 10" and larger shall be stress relieved.
3. A design factor of 0.6 and grade B material have been used to determine wall thickness under B31.8.Higher strength material may be used where appropriate.
4. For 1/2" use VNT-2501 or VNT-2504. For 3/4" use VNT-2503 or VNT-2505.5: ERW pipe can be used for 10-inch and above piping. However, it shall NOT be used for Gas Service and H2S service.
6: B31.8 shall be used for all Liquid or Gas dominated services for wellheads, artificial lift piping, flowlines and any piping outside the main facility
7: Pipe de-rating starts after a temperature of 250 DegF.
8: Refer to Appendix-C for valve specifications with socket-weld end connections
8/13/2019 ENTS 400 Rev5
30/62
United Energy Pakistan Ltd.
Specification For Standard
Piping
EN/TS 400
Page 30 of 62
EN/TS-400
Appendix "A"
Rating:
ANSI 1500 lb, RTJ.
Design:
ANSI/ASME B31.3
Service:
FL, P, LHW, R, V
PIPING MATERIAL
SPECIFICATION SHEET
CLASS E1, E3DESIGN
Max. Press. Max Temp. Limited By3705 PSIG 100 F Valves / Flanges
3540 PSIG 150 F Valves / Flanges
3395 PSIG 200 F Valves / Flanges
Hydrotest Pressure:
5557 psig @ 100 DegF
SIZE 1/2 3/4 1 1 1/2 2 3 4 6 8 10 12
PIPE 80 Sch.160
All pipe sizes: SMLS, A-53-
B, A-106-B, API 5L-B
JOINT
CONST.
SW, T &C (2)or
flanged (1) Buttweld and flanged.
FITTINGS
6000lb. F.S, SW
A-105 A-234 WPB SMLS, buttweld, schedule to match pipe
FLANGES
1500 lb. RTJ., SWscr'd (1) ANSI 1500 lb. RTJW.N. All flanges A-105
UNIONS 6000 lb. F.S.G.J. Use flanges All unions A-105
PLUGS
solid hex
head
Bull
plugs
THR'D NIPP.
& SWAGES
Sch. XXS A-106 B
SMLS
GATE
API 602 Class 1500 gatevalve with SW or
Threaded ends
BALL Use globe valve
VBF-1501
FB VBF-1502. VBF-1502 FB
PLUGS
CHECK
VCT-1501, or API 602
Class 1500 valve with
SW ends VCF-1501
GLOBE
VOT-1501, or API 602
Class 1500 valve with
SW ends VOF-1501
NEEDLE (3)
GAGEVNT-2505VNT-2506
V
A
L
V
E
S
BUTTER-
FLY
BOLTING Studs: A-193-B7 Nuts: A-194-2H: all cadmium plated
GASKETS 316 S.S. type "R" ring joint, oval section
NOTES
1. Use only to match equipment and special items.
2. Welds in pipe 6" and larger shall be stress relieved in accordance with the requirements of ANSI B31.3
3. For 1/2" use VNT-2501 or VNT-2504. For 3/4" use VNT-2503 or VNT-2505.
4: Minimum wall thicknesses shown are based on 0.05" corrosion allowance and 100 Deg F design temperature and 12.5% tolerance factor5: Refer to Appendix-C for valve specifications with socket-weld end connections
8/13/2019 ENTS 400 Rev5
31/62
United Energy Pakistan Ltd.
Specification For Standard
Piping
EN/TS 400
Page 31 of 62
EN/TS-400
Appendix "A"
Rating:ANSI 1500 lb,RTJ WN
Design:
ANSI/ASME B31.4
Service:P, LHW, DR
PIPING MATERIAL
SPECIFICATION SHEET
CLASS E2DESIGN
Max. Press. Max Temp. Limited By
3705 PSIG 100 F Flanges / Valves
3540 PSIG 150 F Flanges / Valves3395 PSIG 200 F Flanges / Valves Hydrotest Pressure:4630 psig @ 100 DegF
SIZE 1/2 (5) 3/4 1 1 1/2 2 3 4 6 8 10 12 (6)
PIPE
SMLS A-53-B, A-106-B, API
5L-B
SMLS.A-53-B. A-106-B, API 5L-B SMLS or ERW, A-53-B, A-106-B, API 5L-
B (5)
SCHEDULE 80 160 140
JOINTCONST.
SW, T &C, orflanged (1) Buttweld and flanged.
FITTINGS
6000lb. F.S
A-105 A-234 WPB SMLS, buttweld, schedule to match pipe
FLANGES
1500 lbs. R.T.J.
scr'd (1) ANSI 1500 lb. RTJ WN All flanges A-105
UNIONS 6000 lb. F.S.G.J. Use flanges All unions A-105
PLUGS
solid hex
head
Bull
plugs
THR'D NIPP.
& SWAGES
XXS A-106 B
SMLS
GATE
BALL Use globe valves
VBF-1501
VBF-1501 FB VBF-1502. VBF-1502 FB
PLUGS
CHECK VCT-1501 VCF-1502
GLOBE VOT-1501 VOF-1502
NEEDLE (3)
GAGE
VNT-2505 orVNT-2506
V
A
L
V
E
S BUTTER-FLY
BOLTING Studs: A-193-B7 Nuts: A-194-2H: all cadmium plated
GASKETS 316 S.S. type "R" ring joint, oval section
NOTES
1. Use only to match equipment and special items.2. Welds in pipe 8" and larger shall be stres relieved.
3. For 1/2" use VNT-2501 or VNT2504. For 3/4" use VNT-2503 or VNT-2505.
4. Claculated for grade B material. Higher strength materials may be used where appropriate.
5: Available corrosion allowance is 1.97 mm instead of 2mm
6: Available corrosion allowance is 1.79 mm instead of 2mm
7: Refer to Appendix-C for valve specifications with socket-weld end connections
8/13/2019 ENTS 400 Rev5
32/62
United Energy Pakistan Ltd.
Specification For Standard
Piping
EN/TS 400
Page 32 of 62
EN/TS-400
Appendix "A"
Rating:ANSI 1500 lb, RTJ WN
Design:ANSI/ASME B31.8 (6)
Service:
P
PIPING MATERIAL
SPECIFICATION SHEET
CLASS E4DESIGN
Max. Press. Max Temp. Limited By3705 PSIG 100 F Flanges / Valves
3540 PSIG 150 F Flanges / Valves
3395 PSIG 200 F Flanges / ValvesHydrotest Pressure:
4630 psig @ 100 DegF
SIZE 1/2 3/4 1 1 1/2 2 3 4 6 8 10 12
PIPE (7)
SMLS A-53-B, A-106-B,
API 5L-B
SMLS.A-53-B.
A-106-B, API
5L-B
SMLS.or ERW(5) A-53-B. A-106-B, API 5L-B
SCHEDULE 160 160
JOINT
CONST.
SW, T &C, or
flanged (1) Buttweld and flanged.
FITTINGS
6000 lb. F.S, SWA-105 A-234 WPB SMLS, buttweld, schedule to match pipe
FLANGES
1500 lbs. R.T.J., SW or scr'd
(1) ANSI 1500 lb.RTJ.W.N All flanges A-105
UNIONS 6000 lb. F.S.G.J. Use flanges All unions A-105
PLUGS
solid hexhead
Bullplugs
THR'D NIPP.
& SWAGES
XXS A-106 B
SMLS
GATE
API 602 Class 1500 gate
valve with SW or Threaded
ends
BALL Use globe valves
VBF-1501
VBF-1501 FB VBF-1502. VBF-1502 FB
PLUGS
CHECK
VCT-1501, or API 602 Class
1500 valve with SW ends VCF-1502
GLOBE
VOT-1501, or API 602 Class
1500 valve with SW ends VOF-1502
NEEDLE (4)
GAGE
VNT-2505 or
VNT-2506
V
A
L
V
E
S
BUTTER-
FLY
BOLTING Studs: A-193-B7 Nuts: A-194-2H: all cadmium plated
GASKETS 316 S.S. type "R" ring joint, oval section
NOTES
1. Use only to match equipment and special items.
2. Welds in pipe 8" and larger shall be stres relieved.
3. A design factor of 0.6 and grade B material have been used to determine the wall thickness. Higher strength amterial may be used whereappropriate.
4. For 1/2" use VNT-2501 or VNT-2504. For 3/4" use VNT-2503 or VNT-2505
5: ERW pipe can be used for 10-inch and above piping. However, it shall NOT be used for Gas Service and H2S service.6: B31.8 shall be used for all Liquid or Gas dominated services for wellheads, artificial lift piping, flowlines and any piping outside the main facility
7: Pipe de-rating starts after a temperature of 250 DegF.
8: Refer to Appendix-C for valve specifications with socket-weld end connections
8/13/2019 ENTS 400 Rev5
33/62
United Energy Pakistan Ltd.
Specification For Standard
Piping
EN/TS 400
Page 33 of 62
EN/TS-400
Appendix "A"
Rating:
ANSI 1500 lb, RTJ WN
Design:
ANSI/ASME B31.8 (6)
Service:P
PIPING MATERIAL
SPECIFICATION SHEET
CLASS E4 - FLOWLINE CONSTRUCTION
DESIGN
Max. Press. Max Temp. Limited By
3705 PSIG 100 F Valves
3540 PSIG 150 F Valves3395 PSIG 200 F Valves
Hydrotest Pressure:4630 psig @ 100 DegF
SIZE 2 3 4 6 8 10 12
PIPE (7) API 5L X46 API 5L X46 (5)
SCHEDULE 160 160 120 160 140 140 140
THICKNESS 0.344 0.438 0.438 0.719 0.812 1.000 1.125
JOINT
CONST. Buttweld and flanged.
FITTINGS A-234 WPB SMLS, buttweld, schedule to match pipe
FLANGES
MSS-SP-44F46 Class 1500 lb.RTJ .W.N
UNIONS Use flanges
PLUGS
THR'D NIPP.& SWAGES
GATE
BALL
VBF-1501
VBF-1501 FB VBF-1502. VBF-1502 FB
PLUGS
CHECK VCF-1502
GLOBE VOF-1502
NEEDLE (4)
GAGE
V
A
L
V
E
S BUTTER-
FLY
BOLTING Studs: A-193-B7 Nuts: A-194-2H: all cadmium platedGASKETS 316 S.S. type "R" ring joint, oval section
NOTES
1. Use only to match equipment and special items.
2. Welds in pipe 8" and larger shall be stress relieved.
3. A design factor of 0.6 and grade B material have been used to determine the wall thickness. Higher strength amterial may be used where
appropriate.4. For 1/2" use VNT-2501 or VNT-2504. For 3/4" use VNT-2503 or VNT-2505
5: ERW pipe can be used for 10-inch and above piping. However, it shall NOT be used for Gas Service and H2S service.
6: B31.8 shall be used for all Liquid or Gas dominated services for wellheads, artificial lift piping, flowlines and any piping outside the main facility
7: Pipe de-rating starts after a temperature of 250 DegF.
8: Refer to Appendix-C for valve specifications with socket-weld end connections
8/13/2019 ENTS 400 Rev5
34/62
United Energy Pakistan Ltd.
Specification For Standard
Piping
EN/TS 400
Page 34 of 62
EN/TS-400
Appendix "A"
Rating:
ANSI 2500 lb, R.T.J.Design:
ANSI/ASME B31.3Service:
FL, P, LHW, R, V
PIPING MATERIAL
SPECIFICATION SHEETCLASS F1, F3
DESIGNMax. Press. Max Temp. Limited By
6000 PSIG 100 F Fittings5897 PSIG 150 F Valves / Flanges
5655 PSIG 200 F Valves / FlangesHydrotest Pressure:
9000 psig @ 100 DegF
SIZE 1/2 3/4 1 1 1/2 2 3 4
PIPEXXS Higher strength material required
All Pipie Sizes: SMLS, A-
53-B, A-106-B, API 5L-B
JOINT
CONST.
SW, T &C, or
flanged (1) Buttweld and flanged.
FITTINGS
6000 lb. F.S, SW
A-105 A-234 WPB SMLS, buttweld, schedule to match pipe
FLANGES
ANSI 2500 lbs. R.T.J., SW or
scr'd (1) ANSI 2500 lb. RTJ.W.N All flanges A-105
UNIONS 6000 lb. F.S.G.J. Use flanges All unions A-105
PLUGS
solid hex
head
Bull
plugs
THR'D NIPP.
& SWAGES
XXS A-106 B
SMLS
GATE
MSS SP-84a Class 2500 gate
valve with SW ends
BALL Use globe valves
VBF-2501
VBF-2501 FB VBF-2502. VBF-2502 FB
PLUGS
CHECK
VCT-5001 or MSS SP-84a Class2500 gate valve with SW ends
GLOBE
MSS SP-84a Class 2500 gate
valve with SW ends
NEEDLE (2)
GAGE
VNT-2505 or
VNT-2506
V
A
L
V
E
S
BUTTER-
FLY
BOLTING Studs: A-193-B7 Nuts: A-194-2H: all cadmium plated
GASKETS 316 S.S. type "R" ring joint, oval section
NOTES
1. Use only to match equipment and special items.
2. For 1/2" use VNT-2501 or VNT-2504. For 3/4" use VNT-2503 or VNT-2505
3. Minimum wall thicknesses shown are based on 0.05" corrosion allowance and 100 Deg F design temperature and 12.5% tolerance factor
4: Refer to Appendix-C for valve specifications with socket-weld end connections
8/13/2019 ENTS 400 Rev5
35/62
United Energy Pakistan Ltd.
Specification For Standard
Piping
EN/TS 400
Page 35 of 62
EN/TS-400
Appendix "A"
Rating:
ANSI 2500 lb, R.T.J. WN
Design:
ANSI/ASME B31.4Service:
P, LHW, DR
PIPING MATERIAL
SPECIFICATION SHEETCLASS F2
DESIGN
Max. Press. Max Temp. Limited By
6000 PSIG 100 F Fittings5897 PSIG 150 F Flanges / Valves
5655 PSIG 200 F Flanges / ValvesHydrotest Pressure:
7500 psig @ 100 DegF
SIZE 1/2 3/4 1 1 1/2 2 3 4 6
PIPESMLS, A-53-B, A-106-B, API 5L-B High strength material required
SCHEDULE XXS
JOINT
CONST.
SW, T &C, or
flanged (1) Buttweld and flanged.
FITTINGS
6000 lb. F.SA-105 A-234 WPB SMLS, buttweld, schedule to match pipe
FLANGES
ANSI 2500 lbs. R.T.J.
scr'd (1) ANSI 2500 lb. RTJ W.N All flanges A-105
UNIONS 6000 lb. F.S.G.J. Use flanges All Unions A-105
PLUGS
solid hex
head
Bull
plugs
THR'D NIPP.
& SWAGES
XXS A-106 B
SMLS
GATE
BALL Use globe valves
VBF-2501
VBF-2501 FB VBF-2502. VBF-2502 FB
PLUGS
CHECK VCT-5001 VCF-2501
GLOBE
NEEDLE (3)
GAGE
VNT-2505 orVNT-2506
V
A
L
V
E
S
BUTTER-FLY
BOLTING Studs: A-193-B7 Nuts: A-194-2H: all cadmium plated
GASKETS 316 S.S. type "R" ring joint, oval section
NOTES
1. Use only to match equipment and special items.2. For 1/2" use VNT-2501 or VNT-2504. For 3/4" use VNT-2503 or VNT-2505
3. Calculated for grad B material. Higher strength materials may be used where appropriate.
4: Refer to Appendix-C for valve specifications with socket-weld end connections
8/13/2019 ENTS 400 Rev5
36/62
United Energy Pakistan Ltd.
Specification For Standard
Piping
EN/TS 400
Page 36 of 62
EN/TS-400
Appendix "A"
Rating:ANSI 2500 lb, R.T.J.WN
Design:ANSI/ASME B31.8 (4)
Service:
FL, P, LHW, R, V
PIPING MATERIAL
SPECIFICATION SHEET
CLASS F4DESIGN
Max. Press. Max Temp. Limited By
6000 PSIG 100 F Fittings5897 PSIG 150 F Flanges / Valves
5655 PSIG 200 F Flanges / ValvesHydrotest Pressure:7500 psig @ 100 DegF
SIZE 1/2 3/4 1 1 1/2 2 3 4
PIPE (5)
SMLS, A-53-B, A-106-B, API
5L-B
SMLS, A-53-
B, A-106-B,
API 5L-B
High strength material required (6)
SCHEDULE XXS XXS
JOINT
CONST.
SW, T &C, or
flanged (1) Buttweld and flanged.
FITTINGS
6000 lb. F.S, SW
A-105 A-234 WPB SMLS, buttweld, schedule to match pipe
FLANGES
ANSI 2500 lbs. R.T.J., SW or
scr'd (1) ANSI 2500 lb. RTJ WN All flanges A-105
UNIONS 6000 lb. F.S.G.J. Use flanges All unions A-105
PLUGS
solid hex
head
Bull
plugs
THR'D NIPP.
& SWAGES
XXS A-106 B
SMLS
GATE
MSS SP-84a Class 2500 gate
valve with SW ends
BALL Use globe valves
VBF-2501
VBF-2501 FB VBF-2502. VBF-2502 FB
PLUGS
CHECK
VCT-5001 or MSS SP-84a Class
2500 gate valve with SW ends VCF-2501
GLOBEMSS SP-84a Class 2500 gatevalve with SW ends
NEEDLE (3)
GAGE
VNT-2505 orVNT-2506
V
A
L
V
E
S
BUTTER-FLY
BOLTING Studs: A-193-B7 Nuts: A-194-2H: all cadmium plated
GASKETS 316 S.S. type "R" ring joint, oval section
NOTES
1. Use only to match equipment and special items.
2. A design factor of 0.60 and grade B material have been used to determine the wall thickness. Higher strength material may be used where appropriate.3. For 1/2" use VNT-2501 or VNT-2504. For 3/4" use VNT-2503 or VNT-2505
4: B31.8 shall be used for all Liquid or Gas dominated services for wellheads, artificial lift piping, flowlines and any piping outside the main facility
5: Pipe de-rating starts after a temperature of 250 DegF.
6: Refer to ASME 2500 Class Piping Specifications for Pipeline construction
8: Refer to Appendix-C for valve specifications with socket-weld end connections
8/13/2019 ENTS 400 Rev5
37/62
8/13/2019 ENTS 400 Rev5
38/62
United Energy Pakistan Ltd.
Specification For Standard
Piping
EN/TS 400
Page 38 of 62
EN/TS-400
Appendix "A"
pg. 21 of 28
Rating:
API 5000 lb, R.T.J.
Service:P, LHW
PIPING MATERIAL
SPECIFICATION SHEETCLASS G1, G3
DESIGN
Max. Press. Max Temp. Limited By5000 PSIG 250 F Fittings
Design:ANSI/ASME B31.3
SIZE 1/2 3/4 1 1 1/2 2 3 4
PIPE Sch 160
SMLS, A-53-B, A-106-B, API 5L-
B, XXS
JOINT
CONST.
SW, T &C (2), or
flanged (3) Buttweld and flanged.
FITTINGS
6000 lb. F.S, SW
A-105 A-234 WPB SMLS, buttweld, schedule to match pipe
FLANGES
5000 lbs. API R.T.J., SW or
scr'd (2), (3) 5000 lb. API 6A W.N., R.T.J. Types 2&4 (1)
UNIONS 6000 lb. F.S.G.J. Use flanges All unions A-105
PLUGS
solid hexhead
Bullplugs
THR'D NIPP.
& SWAGES
Sch XXS A-106 B
SMLS
GATEMSS SP-84a Class 2500 gate valvewith SW ends
BALL Use globe valves VBF-5001. VBF-5001 FB
PLUGS
CHECK
VCT-5001 or MSS SP-84a Class
2500 gate valve with SW ends VCF-2501
GLOBE
MSS SP-84a Class 2500 gate valve
with SW ends
NEEDLE (4)
GAGE
VNT-2505 or
VNT-2506
V
A
L
V
E
S
BUTTER-
FLY
BOLTING Studs: A-193-B7 Nuts: A-194-2H: all cadmium plated
GASKETS 316 S.S. type "R" ring joint, oval section
NOTES
1. Weld neck flange material to be API 6A Type 4. Blind flange material to be Type 2.2. Threads shall conform to ANSI B2.1.
3. Use only to match equipment and special items.
4. For 1/2" use VNT-2501 or VNT-2504. For 3/4" use VNT-2503 or VNT-2505
5: Refer to Appendix-C for valve specifications with socket-weld end connections
8/13/2019 ENTS 400 Rev5
39/62
United Energy Pakistan Ltd.
Specification For Standard
Piping
EN/TS 400
Page 39 of 62
EN/TS-400
Appendix "A"
Rating:
API 5000 lb, R.T.J.
Design:
ANSI/ASME B31.4
Service:P, LHW
PIPING MATERIAL
SPECIFICATION SHEET
CLASS G2
DESIGN
Max. Press. Max Temp. Limited By5000 PSIG 250 F Flanges Hydrotest Presure:6250 psig @ 100 Deg F
SIZE 1/2 3/4 1 1 1/2 2 3 4 6 8 10 12
PIPE
SMLS, A-53-B, A-106-B, API 5L-BSch 160
JOINT
CONST.
SW, T &C (2), or
flanged (3) Buttweld and flanged.
FITTINGS
6000 lb. F.S
A-105 A-234 WPB SMLS, buttweld, schedule to match pipe
FLANGES
5000 lbs. API R.T.J.scr'd (2), (3) 5000 lb. API 6A W.N., R.T.J. Types 2&4 (1)
UNIONS 6000 lb. F.S.G.J. Use flanges All unions A-105
PLUGS
solid hex
head
Bull
plugs
THR'D NIPP.
& SWAGES
Sch XXS A-106 B
SMLS
GATEBALL Use globe valves VBF-5001. VBF-5001 FB
PLUGS
CHECK VCT-5001 VCF-5001
GLOBE VOT-5001
NEEDLE (4)
GAGE
VNT-2505 orVNT-2506
V
A
L
V
E
S
BUTTER-
FLY
BOLTING Studs: A-193-B7 Nuts: A-194-2H: all cadmium plated
GASKETS 316 S.S. type "R" ring joint, oval section
NOTES
1. Weld neck flange material to be API 6A Type 4. Blind flange material to be Type 2.
2. Threads shall conform to ANSI B2.1.
3. Use only to match equipment and special items.4. For 1/2" use VNT-2501 or VNT-2504. For 3/4" use VNT-2503 or VNT-2505
5. Refer to Appendix-C for valve specifications with socket-weld end connections
8/13/2019 ENTS 400 Rev5
40/62
United Energy Pakistan Ltd.
Specification For Standard
Piping
EN/TS 400
Page 40 of 62
EN/TS-400
Appendix "A"
Rating:API 5000 lb, R.T.J.
Design:ANSI/ASME B31.8
Service:P
PIPING MATERIAL
SPECIFICATION SHEET
CLASS G4DESIGN
Max. Press. Max Temp. Limited By5000 PSIG 250 F Flanges
Hydrotest Presure:6250 psig @ 100 Deg F
SIZE 1/2 3/4 1 1 1/2 2 3 4 6
SMLS, A-53-B, A-106-B, API 5L-BPIPE 160 160 160 XXS XXS XXS XXS
JOINT
CONST.
SW, T &C (2), or
flanged (3) Buttweld and flanged.
FITTINGS
6000 lb. F.S, SWA-105 A-234 WPB SMLS, buttweld, schedule to match pipe
FLANGES
5000 lbs. API R.T.J., SW or
scr'd (2), (3) 5000 lb. API 6B W.N., R.T.J. Types 2&4 (1)
UNIONS 6000 lb. F.S.G.J. Use flanges All unions A-105
PLUGS
solid hex
head
Bull
plugs
THR'D NIPP.& SWAGES
Sch XXS A-106 BSMLS
GATE
MSS SP-84a Class 2500 gate
valve with SW ends
BALL Use globe valves VBF-5001. VBF-5001 FB
PLUGS
CHECK
VCT-5001 or MSS SP-84aClass 2500 gate valve with
SW ends VCF-5001
GLOBE
MSS SP-84a Class 2500 gate
valve with SW ends
NEEDLE (5)
GAGE
VNT-2505 orVNT-2506
V
A
L
V
E
S
BUTTER-FLY
BOLTING Studs: A-193-B7 Nuts: A-194-2H: all cadmium plated
GASKETS 316 S.S. type "R" ring joint, oval section
NOTES
1. Weld neck flange material to be API 6A Type 4. Blind flange material to be Type 2.
2. Threads shall conform to ANSI B2.1.
3. Use only to match equipment and special items.
4. A design factor of 0.60 and grade B material have been used to determine the wall thickness. Higher strength material may be used where
appropriate.5. For 1/2" use VNT-2501 or VNT-2504. For 3/4" use VNT-2503 or VNT-2505
6: Refer to Appendix-C for valve specifications with socket-weld end connections
8/13/2019 ENTS 400 Rev5
41/62
United Energy Pakistan Ltd.
Specification For Standard
Piping
EN/TS 400
Page 41 of 62
EN/TS-400
Appendix "A"
Rating:
ANSI 150 lb, R.F.
Service:FL, P, CH, UW (2), LHW, DR, R, V
PIPING MATERIAL
SPECIFICATION SHEETCLASS SSA1
DESIGN
Max. Press. Max Temp. Limited By
285 PSIG 100 F Flanges272 PSIG 150 F Valves
SIZE 1/2 3/4 1 1 1/2 2 3 4 6 8 10 12
PIPE Sch. 80S Sch 10SAll pipe SMLS A-312-TP 316
JOINT
CONST.
SW, T &C, or
flanged (1) Buttweld and flanged.
FITTINGS
3000 lb. F.S
A-182-F316 A403-WP316S SMLS, buttweld, schedule to match pipe
FLANGES
ANSI 150 lbs. R.F.
scr'd (1) ANSI 150 lb. R.F.W.N. All flanges A-182-F316
UNIONS 3000 lb. S.S.G.J. Use flanges All unions A-182-F316
PLUGS
solid hex
head
Bull
plugs 316 SS plugs
THR'D NIPP.
& SWAGES
XXS, A-312-TP316
SMLS
GATE
BALL
VBT-601
VBT-601 FB
VBF-151,
VBF-151 FB VBF-152, VBF-152 FB
PLUGS
CHECK VCT-601 VCF-151
GLOBE VOT-601
NEEDLE (4)
GAGE
VNT-2505 orVNT-2506
V
A
L
V
E
S BUTTER-FLY VBFF-151, VBFF-154
BOLTING Studs: A-193-B8M Nuts: A-194-8M (use copper base thread lube)
GASKETS 316 S.S. type "R" ring joint, oval section
NOTES
1. Use only to match equipment and special items.
2. Use for seawater piping upstream of watermaker only.3. Size of pipe based on T= 100 F
4. For 1/2" use VNT-2501 or VNT-2504. For 3/4" use VNT-2503 or VNT-2505
5. Refer to Appendix-C for valve specifications with socket-weld end connections
8/13/2019 ENTS 400 Rev5
42/62
United Energy Pakistan Ltd.
Specification For Standard
Piping
EN/TS 400
Page 42 of 62
EN/TS-400
Appendix "A"
Rating:ANSI 300 lb, R.F.
Service:
FL, P, CH, UW (2), LHW, DR, R, V
PIPING MATERIAL
SPECIFICATION SHEET
CLASS SSB1
DESIGNMax. Press. Max Temp. Limited By
740 PSIG 100 F Flanges
707 PSIG 150 F Valves
SIZE 1/2 3/4 1 1 1/2 2 3 4 6 8 10 12
PIPE Sch. 80S Sch 10S Sch 40SAll pipe SMLS A-312-TP 316
JOINTCONST.
SW, T &C, orflanged (1) Buttweld and flanged.
FITTINGS
3000 lb. F.S
A-182-F316 A403-WP316S SMLS, buttweld, schedule to match pipe
FLANGES
ANSI 300 lbs. R.F.
scr'd (1) ANSI 300 lb. R.F.W.N. All flanges A-182-F316
UNIONS 3000 lb. S.S.G.J. Use flanges All unions A-182-F316
PLUGS
solid hex
head
Bull
plugs 316 SS plugs
THR'D NIPP.& SWAGES
XXS, A-312-TP316SMLS
GATE
BALL
VBT-601
VBT-601 FB
VBF-301,
VBF-301 FB VBF-302, VBF-302 FB
PLUGS
CHECK VCT-601 VCF-301
GLOBE VOT-601
NEEDLE (4)
GAGE
VNT-2505 orVNT-2506
V
A
L
V
E
SBUTTER-FLY
BOLTING Studs: A-193-B8M Nuts: A-194-8M (use copper base thread lube)
GASKETS 1/8" thick 304 S.S. Flexitallic "CG" or equal
NOTES
1. Use only to match equipment and special items.
2. Use for seawater piping upstream of watermaker only.
3. Size of pipe based on T= 100 F
4. For 1/2" use VNT-2501 or VNT-2504. For 3/4" use VNT-2503 or VNT-25055. Refer to Appendix-C for valve specifications with socket-weld end connections
8/13/2019 ENTS 400 Rev5
43/62
United Energy Pakistan Ltd.
Specification For Standard
Piping
EN/TS 400
Page 43 of 62
EN/TS-400
Appendix "A"
Rating:
ANSI 600 lb, R.F.
Service:
FL, P, CH, UW (2), LHW, DR, R, V
PIPING MATERIAL
SPECIFICATION SHEET
CLASS SSC1DESIGN
Max. Press. Max Temp. Limited By1480 PSIG 100 F Flanges
1415 PSIG 150 F Valves
SIZE 1/2 3/4 1 1 1/2 2 3 4 6 8 10 12
PIPE Sch. 80S Sch 40S
Sch80S
All pipe SMLS A-312-TP 316
JOINT
CONST.
SW, T &C, or
flanged (1) Buttweld and flanged.
FITTINGS
3000 lb. F.S
A-182-F316 A403-WP316S SMLS, buttweld, schedule to match pipe
FLANGES
ANSI 600 lbs. R.F.scr'd (1) ANSI 600 lb. R.F.W.N. All flanges A-182-F316
UNIONS 3000 lb. S.S.G.J. Use flanges All unions A-182-F316
PLUGS
solid hex
head
Bull
plugs 316 SS plugs
THR'D NIPP.& SWAGES
XXS, A-312-TP316SMLS
GATE
BALL
VBT-601VBT-601 FB
VBF-601,VBF-601 FB VBF-602, VBF-602 FB
PLUGS
CHECK VCT-601 VCF-601
GLOBE VOT-601
NEEDLE (4)
GAGE
VNT-2505 or
VNT-2506
V
A
L
V
E
SBUTTER-FLY
BOLTING Studs: A-193-B8M Nuts: A-194-8M (use copper base thread lube)
GASKETS 1/8" thick 304 S.S. Flexitallic "CG" or equal
NOTES
1. Use only to match equipment and special items.2. Use for seawater piping upstream of watermaker only.
3. Size of pipe based on T= 100 F
4. For 1/2" use VNT-2501 or VNT-2504. For 3/4" use VNT-2503 or VNT-2505
5. Refer to Appendix-C for valve specifications with socket-weld end connections
8/13/2019 ENTS 400 Rev5
44/62
United Energy Pakistan Ltd.
Specification For Standard
Piping
EN/TS 400
Page 44 of 62
EN/TS-400
Appendix "A"
Rating:ANSI 900 lb, R.F.
Service:
FL, P, CH, UW (2), LHW, DR, R, V
PIPING MATERIAL
SPECIFICATION SHEET
CLASS SSD1
DESIGN
Max. Press. Max Temp. Limited By2220 PSIG 100 F Flanges
2122 PSIG 150 F Valves
SIZE 1/2 3/4 1 1 1/2 2 3 4 6 8 10 12
PIPE Sch. 80S Sch. 100SAll pipe SMLS A-312-TP 316
JOINT
CONST.
SW, T &C, or
flanged (1) Buttweld and flanged.
FITTINGS
3000 lb. F.S
A-182-F316 A403-WP316S SMLS, buttweld, schedule to match pipe
FLANGES
ANSI 900 lbs. R.F.
scr'd (1) ANSI 900 lb. R.F.W.N. All flanges A-182-F316
UNIONS 3000 lb. S.S.G.J. Use flanges All unions A-182-F316
PLUGS
solid hex
head
Bull
plugs 316 SS plugs
THR'D NIPP.
& SWAGES
XXS, A-312-TP316
SMLS
GATE
BALL
VBT-901
VBT-901 FB
VBF-901,
VBF-901 FB VBF-902, VBF-902 FB
PLUGS
CHECK VCT-901 VCF-901
GLOBE VOT-901
NEEDLE (4)
GAGE
VNT-2505 or
VNT-2506
V
A
L
V
E
SBUTTER-
FLY
BOLTING Studs: A-193-B8M Nuts: A-194-8M (use copper base thread lube)
GASKETS 1/8" thick 304 S.S. Flexitallic "CG" or equal
NOTES
1. Use only to match equipment and special items.2. Use for seawater piping upstream of watermaker only.
3. Size of pipe based on T= 100 F
4. For 1/2" use VNT-2501 or VNT-2504. For 3/4" use VNT-2503 or VNT-2505
5. Refer to Appendix-C for valve specifications with socket-weld end connections
8/13/2019 ENTS 400 Rev5
45/62
United Energy Pakistan Ltd.
Specification For Standard
Piping
EN/TS 400
Page 45 of 62
EN/TS-400
Appendix "A"
Rating:ANSI 1500 lb, R.F.
Service:
FL, P, CH, UW (2), LHW, DR, R, V
PIPING MATERIAL
SPECIFICATION SHEET
CLASS SSE1
DESIGNMax. Press. Max Temp. Limited By
3705 PSIG 100 F Flanges
3540 PSIG 150 F Valves
SIZE 1/2 3/4 1 1 1/2 2 3 4 6 8 10 12
PIPE Sch. 80S Sch. 160SAll pipe SMLS A-312-TP 316
JOINTCONST.
SW, T &C, orflanged (1) Buttweld and flanged.
FITTINGS
3000 lb. F.S
A-182-F316 A403-WP316S SMLS, buttweld, schedule to match pipe
FLANGES
ANSI 1500 lbs. R.F.
scr'd (1) ANSI 1500 lb. R.F.W.N. All flanges A-182-F316
UNIONS 6000 lb. S.S.G.J. Use flanges All unions A-182-F316
PLUGS
solid hex
head
Bull
plugs 316 SS plugs
THR'D NIPP.& SWAGES
XXS, A-312-TP316SMLS
GATE
BALL
VBT-1501
VBT-1501 FB
VBF-1501,
VBF-1501 FB VBF-1502, VBF-1502 FB
PLUGS
CHECK VCT-1501 VCF-1501
GLOBE VOT-1501
NEEDLE (4)
GAGE
VNT-2505 or
VNT-2506
V
A
L
V
E
SBUTTER-
FLY
BOLTING Studs: A-193-B8M Nuts: A-194-8M (use copper base thread lube)
GASKETS 1/8" thick 304 S.S. Flexitallic "CG" or equal
NOTES
1. Use only to match equipment and special items.
2. Use for seawater piping upstream of watermaker only.
3. Size of pipe based on T= 100 F
4. For 1/2" use VNT-2501 or VNT-2504. For 3/4" use VNT-2503 or VNT-2505
5. Refer to Appendix-C for valve specifications with socket-weld end connections
8/13/2019 ENTS 400 Rev5
46/62
United Energy Pakistan Ltd.
Specification For Standard
Piping
EN/TS 400
Page 46 of 62
APPENDIX B
VALVE SPECIFICATION
8/13/2019 ENTS 400 Rev5
47/62
United Energy Pakistan Ltd.
Specification For Standard
Piping
EN/TS 400
Page 47 of 62
The valves listed in this specification meet the requirements of the valves specified for use with
piping classifications and service designations contained in Appendix A.
The valve tag numbering system is as follows:
Sequential number forvarious sizes and types ofvalves
Pressure Class15=ASME 15030=ASME 30060=ASME60090=ASME 900150=ASME 1500250=ASME 2500500=API 5000
V
Valve TypeB=BallBF=ButterflyC=Check
G=GateO=GlobeN=Needle
Construction TypeT=ThreadedF=Flanged
Construction TypeT=ThreadedF=Flanged
8/13/2019 ENTS 400 Rev5
48/62
8/13/2019 ENTS 400 Rev5
49/62
United Energy Pakistan Ltd.
Specification For Standard
Piping
EN/TS 400
Page 49 of 62
2" and larger VBFF-152 Wafer Wafer body, Buna seat, aluminium bronze disc, 150 #Posi-SealKF Ser M
2" and larger VBFF-153 Lug Lug body, Buna seat, nickle plated disc, 150 #Posi-SealKF Ser M
2" and larger VBFF-154 Lug Lug body, Buna seat, SS internals, 150 #Posi-SealKF Ser M
2" and larger VBFF-155 Lug Lug body, Buna seat, aluminium bronze disc, 150 #Posi-SealKF Ser M
(1) Use full port on lines to be pigged, near meter runs, and at relief valve inlets.
(2) All ball valves shall be fire safe design.
(3) Seats and seals shall be designed for full flange rating at 250F.
(4) Check valves 2" and larger shall have 1/2" NPT opening in the cover for bleeding.
(5) Butterfly valve design must be able to open fully between flanges bored for Sch 80 pipe. Butterfly valves shall be rated for 285 psig at 100 DegF. Maximum working tempera
(6) Use lug type valve only when flanged directly to equipment
8/13/2019 ENTS 400 Rev5
50/62
8/13/2019 ENTS 400 Rev5
51/62
United Energy Pakistan Ltd.
Specification For Standard
Piping
EN/TS 400
Page 51 of 62
(2) All ball valves shall be fire safe design.
(3) Seats and seals shall be designed for full flange rating at 250F.
(4) Check valves 2" and larger shall have 1/2" NPT opening in the cover for bleeding.
8/13/2019 ENTS 400 Rev5
52/62
8/13/2019 ENTS 400 Rev5
53/62
United Energy Pakistan Ltd.
Specification For Standard
Piping
EN/TS 400
Page 53 of 62
Check Valves(4)
1-1/2" & Smaller VCT-601
1440# min. CWP, CS Body, Threaded ends, full openingswing check, resilient seat.Purchaser to specify flow direction if other than horizontal
KFKFKFWheatley
Ser 31Ser 31Ser 31Fig. 33
2" and largerVCF-601VCF-602
Raised FaceRTJ
600# ANSI, raised face or RTJ flanged, carbon steel body,bolted bonnet, full opening swing check,resilient seat,bodytap and plug on both ends of clapper pin.Purchaser must specify "For Vertical Flow" when requiredby the piping configuration.
CraneCraneWheatleyWheatleyKF
175X175XU15651564Ser 35
(1) Use full port on lines to be pigged, near meter runs, and at relief valve inlets.
(2) All ball valves shall be fire safe design.
(3) Seats and seals shall be designed for full flange rating at 250F.
(4) Check valves 2" and larger shall have 1/2" NPT opening in the cover for bleeding.
8/13/2019 ENTS 400 Rev5
54/62
United Energy Pakistan Ltd.
Specification For Standard
Piping
EN/TS 400
Page 54 of 62
ASME / ANSI 900 ClassBALL VALVES (1)(2)(3)
SIZE RANGE VALVE TAG VALVE TYPE DESCRIPTION MANUFACTURER FIG. NO
2"-4"VBF-901VBF-901-FB
Regular PortFull Port
900# ANSI RTJ flanged,carbon steel body andbonnet,lever and handwheel operated,trunnionmounted ballBall:Orbit:AISI 1030 forged steel or ASTM A-216 Gr.
WCC cast steelGrove/Omega: Steel -AISI 1018 or 4140kel plated.Stem:Orbit:AISI 8620 alloy steel with nickel platedthreadsGrove/Omega: Steel-AISI 1018 or 4140 electrolessnickel coatedSeat: Teflon or reinforced teflon
OrbitGrove/Omega
T3 Standard
6"VBF-902VBF-902-FB
Regular PortFull Port
900# ANSI RTJ flanged,carbon steel body andbonnet,lever gear operated,trunnion mounted ballBall:Orbit:ASTM A-216 Gr. WCC cast steelGrove:Omega: Steel -ASTM A-148 Gr.90-60 nickelplated.Stem:Orbit:ETD 150 alloy steelGrove/Omega: Steel-AISI C-1213,C-1018 electrolessnickel coatedSeat: Teflon or reinforced teflon
OrbitGrove/Omega
T3 Standard
8" and largerVBF-902VBF-902-FB
Regular PortFull Port
900# ANSI RTJ flanged,carbon steel body andbonnet,lever gear operated,trunnion mounted ball
Ball:KF:Carbon steel 1018WKM:ASTM A-105 CS ENC.Stem:Carbon steel 1018WKM: ASTM A322 Gr. 4140 AS ENCSeat: Teflon or reinforced teflon
KFWKM
Ser TDynaSeal 370D-4
Globe Valves
2" and larger VOF-901 900# ANSI, RTJ globe Crane 183XU
Check Valves(4)
2" and larger VCF-901 Raised Face
900# ANSI, RTJ flanged, carbon steel body, boltedbonnet, full opening swing check,resilient seat,body tapand plug on both ends of clapper pin.Purchaser must specify "For Vertical Flow" whenrequired by the piping configuration.
WheatleyKF
1574Ser 35
(1) Use full port o