Whitecroft Lighting LimitedBurlington Street, Ashton-under-Lyne, Lancashire OL7 0AX

Telephone +44 (0)870 5 087 087 Facsimile: +44 (0)870 5 084 210

Registered No. 3848973 England Registered Office: As above

GENERAL INFORMATIONA qualified electrician, in accordance with IEE wiring regulations should carry out connection

to mains wiring.Observe ESD precautions during installation.This unit must be EARTHED.Ensure that the rated voltage and frequency requirements are compatible with the available

mains supply.Cleaning of reflectors and lenses should be carried out using clean, soft and lint free cloths

and anti-static cleaning fluidDo not carry out high voltage insulation test, i.e. 500/1000v this may damage internal

components.

FURTHER INFORMATIONTECHNICAL SUPPORT

Telephone: 0161 331 5700E-mail: technical@whitecroftlight.com

http://www.whitecroftlighting.com/

1.

2.3.4.

5.

6.

Installation sheet

Careline

SPECIFICATION:Lamp type: LED

Colour: 4000°K

Finish: White texture

Materials:

Body: Aluminium

Geartrays / Pan: Steel

Diffusers: Acrylic/Polycarbonate

Weight: 50 kgs

Control gear: Dali

Emergency: Integral 3hr/COMEPS

Supply: 240v 50Hz AC

Operating Temperature: 0-25°C

Supply flex: 1.5 - 2.5mm² appropriate to load, run length and electical

protection employed.

Internal wiring: 1.5mm²

Cable entry: From above, into marshalling box

Terminal block: Screw terminals for mains/dali inputs

Ingress protection: IP20

Ceiling compatibility: T15/T25 (special layout required to suit run design)

Plasterboard aperture lined with battens

PK/LEAFLETCLINE Revision: 3 Jan/17

CarelineWhitecroft Lighting Limited

1 Prepare aperture - suspended ceiling grid only

2 Suspend BodyONLY SUSPEND FROM SOLID CEILING. ENSURE

CABLES, ANCHOR POINTS / BOLTS ARE

SUITABLY RATED FOR THE PRODUCTS

WEIGHT. USE A SUITABLY RATED PLATFORM

TO SUPPORT FITTING WHILST DROP RODS /

SUSPENSION WIRES ARE FIXED.

1185

OVER

ALL

FLAN

GE W

IDTH

-

1173

TYPI

CAL

MIN. C

UT A

PERT

URE

-

1785OVERALL FLANGE WIDTH -

TYPICAL MIN. CUT APERTURE - 1770

WIRE SUSPENSION HOOKS (SUPPLIED BY OTHERS)

DROP ROD SUSPENSION (SUPPLIED BY OTHERS)

900

M10

DROP

ROD

CEN

TRES

-

760

M6 D

ROP

ROD

CENT

RES

-1200M6/M10 DROP ROD AND WIRE SUSPENSION CENTRES -

1090

WIR

E SU

SPEN

SION

CEN

TRES

-

250mm

TYP. HEIGHT (EXCLUDING SUSPENSION FIXINGS)

NOTE ORIENTATION OF CIRCULATION LIGHT - SHOULD BE FACING AWAY FROM BED

CarelineWhitecroft Lighting Limited

3 Install diffusers

To fit, insert both outer edges of

the corner diffuser first.

To remove, reverse the sequence

- lift the diffuser to the outer edges

and remove from the inner edge.

Corners

Fit reading light cover below the

opal diffusers.

Opal sheet

Straight sections and

reading light covers

READING LIGHTS (BED HEAD)EMERGENCY LIGHT

CIRCULATION / NIGHTLIGHT

MARSHALLING BOX

OPAL DIFFUSERS

READING LIGHT COVER

INTERNAL FITTING DRIVER BOX

LINEAR END OF BED LIGHT

CarelineWhitecroft Lighting Limited

4 Control Panels, Switches and Supply

DO NOT POWER UP MARSHALLING BOX UNTIL

ALL DEVICES ARE CONNECTED.

TECHNICAL SUPPORT

Telephone: 0161 331 5700

E-mail: technical@whitecroftlight.com

http://www.whitecroftlighting.com/

MAINS AND DALI FEED TO MARSHALLING BOX(SUPPLIED BY OTHERS)

STANDARD LAYOUT WITH SCENE CONTROL PANEL (IGNORE COLOUR CHANGE PANEL IF PRODUCT IS NOT TUNEABLE WHITE).

OPTIONS FOR USING THE COMDSIU TO CONNECT A SWITCH FOR BEDSIDE CONTROL OF READING LIGHTS (ON/OFF/DIM UP/DIM DOWN)

PLEASE NOTE: THERE MAY

BE MORE LED DEVICES

CONNECTED THAN SHOWN

HERE. TWO 6-POLE

CONNECTORS SHOULD BE

FREE CLOSEST TO SCREW

TERMINALS FOR CONTROL

PANEL AND SWITCH

CONNECTION (VIA COMDSIU)

INTERNAL FITTING CONNECTIONS (UP TO 6X)

DO NOT REMOVE OR SWAP