Upload
others
View
5
Download
0
Embed Size (px)
Citation preview
2010.0 XF (X250), 303-07
ENGINE IGNITION - V8 5.0L PETROL/V8 S/C 5.0L PETROL
IGNITION COIL-ON-PLUG - V8 S/C 5.0L PETROL (G1085794)
REMOVAL AND INSTALLATION
18.20.36
ON PLUG IGNITION
COIL - RENEW
4200 CC, AJ V8,
NATURALLY ASPIRATED
0.2USED
WITHINS
18.20.36
ON PLUG IGNITION
COIL - RENEW
5000 CC, AJ V8,
NATURALLY ASPIRATED
1USED
WITHINS
18.20.36
ON PLUG IGNITION
COIL - RENEW
5000 CC, AJ V8,
SUPERCHARGED1.1
USED WITHINS
18.20.40
ON-PLUG IGNITION
COIL - ENGINE SET - RENEW
3000 CC, AJ-V6
1.2USED
WITHINS
18.20.40
ON-PLUG IGNITION
COIL - ENGINE SET - RENEW
4200 CC, AJ V8,
NATURALLY ASPIRATED
0.6USED
WITHINS
18.20.40
ON-PLUG IGNITION
COIL - 5000 CC, AJ V8,
NATURALLY 2.1
USED WITHINS
ENGINE SET - RENEW
ASPIRATED
18.20.40
ON-PLUG IGNITION
COIL - ENGINE SET - RENEW
5000 CC, AJ V8,
SUPERCHARGED2.2
USED WITHINS
NOTES:
REMOVAL
Removal steps in this procedure may contain installation
details.
Some variation in the illustrations may occur, but the essential
information is always correct.
Refer to: (414-01 Battery, Battery Disconnect and Connect
Mounting and Cables, General Procedures).
1.
Refer to: Engine Cover - V8 5.0L Petrol/V8 S/C 5.0L Petrol
(501-05 Interior Trim and Ornamentation, Removal and
Installation).
2.
Refer to: Secondary Bulkhead Panel RH - TDV6 3.0L Diesel
(501-02 Front End Body /V8 5.0L Petrol/V8 S/C 5.0L Petrol
Panels, Removal and Installation).
3.
4.
CAUTIONS:
Be prepared to collect escaping coolant.
Make sure that all openings are sealed. Use new
blanking caps.
5.
6.
2010.0 XF (X250), 501-02
FRONT END BODY PANELS
SECONDARY BULKHEAD PANEL RH - TDV6 3.0L DIESEL /V8 5.0L PETROL/V8 S/C 5.0L PETROL (G1090271)
Torque: 7 Nm
INSTALLATION
To install, reverse the removal procedure.1.
REMOVAL AND INSTALLATION
76.11.30
ENGINE COMPARTMENT RIGHT HAND
COVER - RENEW
3000 CC, AJ-V6
0.9USED
WITHINS
76.11.30
ENGINE COMPARTMENT RIGHT HAND
COVER - RENEW
3000 CC, TDV6
0.9USED
WITHINS
76.11.30
ENGINE COMPARTMENT RIGHT HAND
COVER - RENEW
5000 CC, AJ V8
0.9USED
WITHINS
NOTE:
REMOVAL
Removal steps in this procedure may contain installation details.
All vehicles
Refer to: (501-02 Front End Secondary Bulkhead Center Panel
Body Panels, Removal and Installation).
1.
Torque: 25 Nm
2.
Right-hand drive vehicles
NOTE:1.
Some variation in the illustrations may occur, but the
essential information is always correct.
Left-hand drive vehicles
1.
NOTE:2.
Some variation in the illustrations may occur, but the
essential information is always correct.
Vehicles with 5.0L
Refer to: (303-12C Intake Air Distribution and Air Cleaner RH
Filtering - V8 5.0L Petrol, Removal and Installation).
1.
Vehicles with diesel engine
1.
All vehicles
1.
2.
INSTALLATION
2010.0 XF (X250), 501-05
INTERIOR TRIM AND ORNAMENTATION
ENGINE COVER - V8 5.0L PETROL/V8 S/C 5.0L PETROL (G1090386)
To install, reverse the removal procedure.1.
REMOVAL AND INSTALLATION
12.29.93ENGINE COVER - RENEW
3000 CC, TDV6
0.1USED
WITHINS
12.29.93ENGINE COVER - RENEW
4200 CC, AJ V8,
NATURALLY ASPIRATED
0.1USED
WITHINS
12.29.93ENGINE COVER - RENEW
5000 CC, AJ V8
0.1USED
WITHINS
NOTE:
REMOVAL
Removal steps in this procedure may contain installation details.
1.
2010.0 XF (X250), 414-01
BATTERY, MOUNTING AND CABLES
BATTERY DISCONNECT AND CONNECT (G1033944)
NOTE:
Some variation in the illustrations may occur, but the
essential information is always correct.
INSTALLATION
To install, reverse the removal procedure.1.
BATTERY DISCONNECT AND CONNECT (G1033944)
GENERAL PROCEDURES
NOTE:
DISCONNECT
If a new battery is installed, the battery monitoring system
(BMS) must be reset using Jaguar approved diagnostic
equipment.
Refer to: Battery and Battery Charging Health and Safety
(100-00 General Information, Description and Precautions
Operation).
1.
Obtain and record the audio unit preset radio frequencies.2.
3.
NOTE:4.
Where fitted.
CAUTION:
Take extra care not to damage the wiring harness.
5.
6.
CAUTION:
Make sure that the battery negative cable does not move
when detaching the negative terminal from the battery.
7.
CONNECT
CAUTION:
Make sure that the battery negative cable to the body
retaining bolt is not loose and fully tightened.
1.
Torque: 13 Nm
Torque: 6 Nm
2.
3.
NOTE:4.
Make sure that both the positive and negative battery
terminals are correctly located.
5.
NOTE:
Where fitted.
NOTE:
Using Jaguar approved diagnostic equipment, reset the
battery monitoring system (BMS).
6.
This step is only necessary when installing a new battery.
Refer to: (501-11 Glass, Door Window Motor Initialization
Frames and Mechanisms, General Procedures).
7.
Enter the audio unit preset radio frequencies.8.
Reset the clock to the correct time.9.
Start the engine and allow to idle until the engine reaches
normal operating temperature.
10.
Switch the engine off.11.