1

Endoscope Reprocessing System

Illustrated Parts Guide 120V/230V

2

MEDIVATORS® and RAPICIDE® is a registered trademark of Medivators Inc.CIDEX® is a registered trademark of Johnson & Johnson.

© 2015 Medivators Inc.

50096-237 REV C

This manual is designed to provide a quick and easy reference to the major replacement parts and components for the CER series endoscope reprocessor. It does not include some of the smaller items such as screws and washers.

The parts listed in this manual are subject to change without notice.

To order parts or request service, contact MEDIVATORS Customer Support.

3

Electronic Circuit Boards, Cables and Accessories

Item Description Part Number

Main Board MB01-0012

Key Pad MB01-0015

Ribbon Cable CC08-0001

Alarm Cable CC08-0503

Level Sensor Harness 37590-094

Fuse CF02-0000

230V Transformer (For 230V units only) CT06-0001

Ribbon Cables (2) CC08-0001

Replay (6) CR03-0000

Alarm Cables CC08-0503

Program Chip See table on next page

Level Support Harness J337590-094

4

Description

Soak Time (min). Bold indicates DEFAULT HLD contact time (see note 1)

Rinses

Chip

60Hz 50Hz

RAPICIDE® HLD 5, 20 ,45 2 32650-029 32650-033

RAPICIDE OPA/28 5, 20,45 2 32650-029 32650-033

Glut 10, 20, 45 2 32650-030 32650-034

Extended Rinse Glut 10, 20,45 2 32650-013 NA

CIDEX® OPA 12, 20,45 3 32650-031 32650-038

CIDEX OPA Extended Rinse 12, 20,45 3 32650-032 32650-039

Note 1: The CER has three HLD contact times. The default contact time is the time the machine will always default to after each cycle. The other two contact times can be selected, but will need to be pressed each time prior to the start of the cycle.

Numerical Overlays for Keypad:5 minute label ML02-0071

RAPICIDE/RAPICIDE OPA kit Kit Part Number Incoming power frequency

MK01-0050 60 Hz (North America)

78399-882 50 Hz

Each kit contains the following:

1. Basin Thermometer and bracket

2. 5 min label

3. Program Chip for specific line frequency

4. Misc. labels

5. Install instructions

5

CER-1 Solution and Air Pump Assembly 78398-631

Harness 37590-092

Plug for ManifoldCP02-0001

Elbow FittingCC10-0009

Alcohol ManifoldCM01-000

Pump Only 41600-230 Same for both120V & 230V

Pump with ManifoldCLM-1071

RectifierCC16-0500

Control Block36030-016

Drain Valves75227-245

Air Pump41600-122

Air Pump Diaphram

CD05-0000

Air FIlterCF01-0019

6

CER-2 Solution and Air Pump Assembly

Air Pump 41600-122

Air Pump Diaphram

CD05-0000

TubingMT01-0000

Drain Block (no fittings)CC10-0006

Nut & FittingCC10-0011

7

Description Part Number

1. Elbow CE01-0000

2. Valve Body 75227-245

3. Straight Fitting CC10-0011

Description Part Number

1. Coil unterminated MMC15-0000

1a. Ring Terminal for coil (1 per coil) 36030-014

1b. Female spade connector (2 per coil) CT05-0501

2. Valve cover (not shown, located below coil) 72233-206

3. Valve Rebuild Kits 78398-949

8

Air Solution Water Valves (ASW)

78398-947 78398-948Spade Connector for ASW valves is CT05-0511 (not included with the ASW valves, must be ordered separate.)

9

Oscillating Pump CER-2

Oscillating Pump CER-1P/N 41600-137

Note: Same pump is used for both 120V and 230V units.

Pump Elbow (1) Straight Fitting (1) 41600-136

Pump Elbows (2) 41600-137

10

All fitting same for the CER-1 basin

Drain Screen43100-325

Thermometer MT10-0001

Bracket72233-165

Thermometer & Bracket AssyASM1-0047

Sensor(under the cap)

MS03-0011

Cap35548-055

Seal75227-506

Scope Hookup(includes nuts)

CB03-0000

O-ring(2) per container

75227-634

11

Description Part Number

1. O-rings (2) per connector 75227-634 One (1) - on the top side of basin One (1) - used on the bottom side of the basin

2. Plates: Two (2) hole 72233-535 (used for CER-1 & CER-2) Three (3) hole 72233-538 (used only on CER-2)

3. Tubing MT01-0005

4. Washer for float sensor CW02-0016

Screw CS05-0017 (2) two for each sensor required

12

Float SensorMS03-0011

Drain CoverCC13-000

Drain Screen43100-325

Sensor Cap75227-506

Sensor Base(not shown)35548-055

SealCO01-0000

13

78398-666 CER-1 Air line 78398-667 CER-2 Air line

CLM-1058 CER-1 78398-681 CER -1

Used for channels 1-4 &7 Used for channels 5&6

T Fitting CE01-00002

TubingCT01-0005

Tubing CT01-0003

Check Valve CV01-0005

Tubing CT01-0005

Tubing CT01-0003

14

Description Part Number

1. Lid with handle CLM-1078

2. Latch ML03-0008

3. Alcohol injection port CC10-0003

4. Counter 45040-060

Lid Assembly CLM-1078

15

Gasket Material (77")MG02-0004

HandleMH04-0002

ScrewsMS05-0070

16

Female AdapterCA01-00018

HingesMH01-0009

Female AdapterCA01-00018

Water Inlet ValveCV01-0002

Power Inlet ModuleCS06-0000

Power Cord37590-472

17

Description Part Number

1. Heated Disinfectant tank CER-1080

2. Set of three HLD tubing (not shown) 78399-141

3. Power Cord for reservoir (not shown) 37590-103

4. Cart only (includes drip tray) CER-1005

5. Drip Tray 75227-371

6. Uptake tube for reservoir (not shown) 78399-246

7. Connector on top of reservoir (metal, not shown) 47509-663

8. Braided water hose CH06-0000

9. Drain Hose CLM-1062

10. Hose clamp for drain hose CC02-0002

18

Description Part Number

Drain Hose CLM-1062

Hose Clamp CC02-0002

Power Cord for reservoir 37590-103

ThermometerMT10-0000

19

Water Pre-Filtration CER-1076

Not Shown: Filter wrench 47049-261

Female Quick ConnectMC10-0043

Male QuickConnectMC10-0042

Pressure Gauge41600-219

Braided Water Hose

CH06-0000Connects to

this fitting

Filter Housingwith Black

CapMF03-0154

O-ring Seal43100-083

Blue Housing Only

MF03-0153

20

Transfer Pump

Description Part Number

Transfer Pump 120V with hose set DSD-1087

Transfer Pump 230V with hose set DSD-1088

Tubing Set MK01-0037

If you have any questions regarding the CER-1, CER-2 Endoscope Reprocessor Parts Guide, please contact MEDIVATORS Customer Support at 1-800-444-4729 or visit our website www.medivators.com.

21

22

23

24www.medivators.com

Manufactured in the USA by:

Medivators Inc. 14605 28th Avenue NorthMinneapolis, MN 55447 USAToll Free: +1.800.444.4729

Medivators BVSourethweg 116422PC HeerlenThe NetherlandsTel: +31.45.5.471.471

Cantel Medical Asia/Paci�c Pte. Ltd.1A International Business Park#05-01 Singapore 609933Tel: +65.6227.9698

Medivators Inc. Beijing Representative Of�ceRoom 1801, Floor 18th, Tower A,Beijing Marriott Hotel, Of�ce BuildingNo. 7, Jianguomen South Avenue,Dongcheng District, Beijing 100005 ChinaTel: +86 10 65204039