Enclosur100Base-TX to 100Base-FX Single Mode SC Fiber Converter (30KM, 18.6 Miles)e Catalogue Products

8/10/2019 Enclosur100Base-TX to 100Base-FX Single Mode SC Fiber Converter (30KM, 18.6 Miles)e Catalogue Products

1/32

Enclosure

s

www.lcautomation.com

Enclosures

Steel enclosures . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 166

Stainless steel enclosures . . . . . . . . . . . . . . . . . . . . . . 177

Hygienic design enclosures . . . . . . . . . . . . . . . . . . . . . 184

Fan and filter units . . . . . . . . . . . . . . . . . . . . . . . . . . . . 186

Enclosure heaters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 188

Cooling units . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 189

Arm system . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .192


2/32

Enclosures explained . . . www.lcautomation.com

Blackburn Office - 01254 685900 Chippenham Office - 01249 460099162

See pages 168-169 The AE range is also available in Stainless Steel see page 178

The KL range is also available in Stainless Steel see page 177

See pages 170-171

Compact enclosures with mounting strips on the door for fast attachment ofsupport strips, cable conduit holders and covers. The door has an openingangle of 130 (180 by request) and the rear panel is supplied with holesprepared for wall mounting bracket or direct wall mounting, The single doorsare hinged on the right, but it is possible to swap these to the left on all exceptthe 200mm wide enclosures. The multi-folded enclosure protection channelprevents dirt and water entering when the door is opened, there is also a PE

conductor connection facility on the enclosure, door and mounting plate. Thegland plates, which are made from sheet steel for self-assembly, may beexchanged for pre-punched plates or plastic gland plates.

The AE range . . .

Available widths:

200, 300, 380,400, 500, 600,760, 800, 1000mm

A E X X X X 5 0 0.

Available widths:

600, 800, 1000,1200mm

Terminal boxes with screw-fastened lid and profile strips with mounting holeson both sides for the installation of cross rails or mounting plate. Cover may beopened and securely locked in a flash, with a quick-action screw. Quarter turninstead of thread ensures correct contact pressure of the seal. Available with orwithout gland plates (enclosures with gland plates include sheet steel gland plateswith seals and assembly parts).

The KL range . . .

Compact system enclosures which combine the case benefits of the AEcompact enclosure with the installation diversity of the TS8 top enclosuresystem. They are an excellent alternative to the larger enclosures in the AEseries. The single doors are hinged on the right, but it is possible to swap theseto the left. The enclosures are supplied with a mounting plate and open basefor individual cable entry.

The CM range . . .

Available widths:

150, 200, 300,400, 500, 600,800mm

Example code:

C M X X X X 5 0 0.

Example code:

See pages 166-167

K L X X X X 5 1 0.Example code:

180 hinges

Base/plinths

Baying kits

Cable glands

Door stays

Eye bolts

Interior rails

LED system lights

Locks with key

Rain canopy

Wall mounting brackets

Wiring plan pockets

Available accessories:

Base configuration rail

Base/plinths

Cable clamp rails

Interior rails

Locking systems

Mounting plate slide block

Punched sections withmounting flanges

Rain canopy/vented roof

Support strips for door

Wiring plan pockets


Cable retainers

Cover hingesCover retainers

Earthing set

Mounting plateSupport rails (DIN rail)

Spare quick release

fastenersWall mounting brackets


RAL 7035

Sheet steel

Colour

Enclosure

RAL 7035

Sheet steel

Colour

Enclosure

RAL 7035

Sheet steel

Colour

Enclosure


3/32

Enclosures explained . . .www.lcautomation.com

163Blackburn Office - 01254 685900 Chippenham Office - 01249 460099

The TS8 range is also available in Stainless Steel see pages 180-181

The SE8 range is also available in Stainless Steel see pages 182-183

See pages 174-176

T S X X X X 5 0 0.Example code:

See pages 172-173

S E X X X X 5 0 0.

Example code:

180 hinges

Adaptor sections

Base/plinths

Baying brackets

Blanking covers

Cable clamp rails

Cable entry sections

Door staysEarth straps

Earthquake kits

Flex-Block

Holder for protective bar

LED system lights

Levelling component

Locking systems

Mounting brackets

Partial doorsPartial mounting plates

Protective bars

Roof plates

Side panels


System lights

Trim panels

Wiring plan pockets


These enclosures consist of two side panels and a roof that are made from onepiece of sheet steel, the rear panel of the enclosure is screwed on for easyaccess and cable entry can be handled in a variety of ways using the integratedbase frame. The door and rear wall are electrically bonded to the enclosureusing a patented hardware system that requires no separate ground straps. Thetwo mounting levels integrated into the enclosure provide more room foroptions, making better use of space while reducing installation time. Theenclosures are available as one and two door versions, the single doors arehinged on the right, but it is possible to swap these to the left. The enclosedbasic frame helps to reduce debris and dirt collection making cleaning easier.The enclosures are highly stable thanks to the self-supporting, integrated frameconstruction. All standard TS8 accessories are compatible.

Available widths:

600, 800, 1000, 1200,1600, 1800mm

Base/plinths

Cable entry plate

Cable clamp rails

Flex-BlockLocking systems

Roof eyebolts

Punched sections withmounting flanges


The TS8 floor standing enclosure is a baying system with a variety of mountingpossibilities. The strength and flexibility of these enclosures come from theirrobust 16 fold, tubular frame which features a 25mm hole pattern that allowscomponents and accessories to be mounted horizontally or vertically. Theycan support loads of up to 3,200lb. Combined with the included zinc-platedmounting panel, the TS8 provides 15% more interior mounting space thansimilar enclosures. Due to its modular design it is easily adaptable to yourunique requirements, each vertical section is able to accommodate thehinges for an enclosure panel, ensuring the units are bayable on all sides.The rear panel can easily be exchanged for a door and both side panels maybe hinged. The TS8 can protect critical equipment in even the most

demanding environments.

The TS8 range . . .

Available widths:

400, 600, 800,1000, 1200mm

RAL 7035

Sheet steel

Colour

Enclosure

The SE8 range . . .

RAL 7035

Sheet steel

Colour

Enclosure


4/32

Accessories explained . . . www.lcautomation.com


Trim panels at the front and rear with fittedcorner pieces and side trim panels.

Base/plinth

All screws, nuts, contact washers andearthing strips needed to earth the cover.

Plinth which acts as a pallet once installed,eliminating the need for a wooden pallet,making it easy to move the enclosurearound. Tool-less assembly once thecorner blocks have been fitted.

With pre-punched holes (metric or PG) forcable glands. Used for sealing standardgland plates.

Temperature range: -40 to +70C

The gland and locknut are supplied in asingle pack, they have clampingmembranes for even tightening and strainrelief which protects the cables. Insulation

is via a plastic insert with optimum seal onthe connection thread thanks to theO-ring. The locknut cuts automatically intothe spray finish, creating a conductiveconnection.

For mounting in the enclosure. Suitablefor mounting on the sides, base and roofareas.

For attaching to the enclosure from theoutside. Supplied with assembly parts.

There are a largeselection oflocking systems

available, e.g. Cam locks Ergoform S lock systems Semi cylinder locks Security locks

For connecting individual enclosuresinto bayed suites. The enclosures are

connected between the base androof frame.

Used to secure enclosure doors in theopen position. Also available with 180hinges for emergency escape routes

For fan and filter units/outlet filters. Easycleaning thanks to exterior silicon coatingapproved for use with foodstuffs.

Easily fitted without drilling and allows thecovers to be opened upwards, even whenthe terminal box below is bayed.

The cover hinge is simply screwed to the

enclosure protection channel and to theedge fold.

For strain relief with cable entry. Thelength of the cable clamp rail is tailored tothe width of the mounting plate. The

supplied mounting bracket can beinstalled straight or tilted.

RAL 7022

Sheet steel

Colour

Material

RAL 7035Colour

Sheet steel

Material

Brass

Sheet steel

Stainless steel

Material

Baying kit

Brackets for wall mounting

Cable clamp rails

Cable glands

Brass

Polymide 6

Material

For individual rail mounting. Flat or inclinedversions available.

Sheet steel

Material

Cable retainers Flex-Block

Gland plates

Hose proof hoods

Cover hinge forKL enclosures

Cover retainerfor KL enclosures

Door stays

Earthing set

Die-cast Zinc

Material

Sheet steel

Material

Stainless steel

Material

Interior rails

Keys/lockingsystems

Sheet steel

Material


5/32

Accessories explained . . .www.lcautomation.com


To compensate for height differences withfloor irregularities.

For component installation outsideof the enclosure.

RAL 7035

Sheet steel

Colour

Material

RAL 7035

Sheet steel

Colour

Material

Sheet steel/Stainless steel

Material

Levelling feet Punched section with or without mounting flange

Support rails

Mounting plate

Quick release fastenerfor KL enclosures

Mounting plate infill

Rain canopy

Sheet steel

Material

Sheet steel

Material

Pole clamp

Pressure reliefstoppers

Sheet steel

Material

Polypropylene

Material

Useful for a continuous mounting surface inbayed suites where the mounting plate isset forward.

For reliable, convenient fastening to roundor square poles.

Helps prevent condensation in sealedenclosures and can also be installed invertical surfaces to protect against dirt.

Roof eyebolts

Wiring plan pockets

For designing flexible interior installation,and/or to accommodate additional built-incomponents. Variable, with five rows ofholes for universal skeleton structures orpartial assembly. Available with or withoutmounting flange.

Ideal for use in inaccessible areas, it isscrew fastened to the mounting bracket atthe front.

Reliable protection for outdoor siting, withwater run-off to the rear. Easily retro-fitted.

For crane transportation of enclosures,available with or without reinforcementplate.

Available in either standard 2m lengths oras sized lengths to fit the enclosure width.

Available widths : 137, 187, 287, 387, 455, 487,555, 587, 755 or 1155mm

Used for attaching cable ducts, cableconduit holders, contact hazard andprotection covers. They are also useful forequipment installed on the door, cableclamping and attachment.

Useful for holding wiring plans during faultfinding and maintenance work. The lecterncan be bayed according to the door widthand is suitable for mounting on the tubulardoor frame.

For fastening to door frames.

Available for direct attachment in all largeenclosures and for mounting on compactenclosures. The range includes standard,courtesy and LED lights.

Plastic

Sheet steel

Material

Wiring plan lectern

System lights

Support strips


6/32

Enclosures www.lcautomation.com


KL Terminal boxes

Technical specification

MaterialEnclosure. . . . . . . . . . . . . . . . Sheet steel

Cover. . . . . . . . . . . Sheet steel, all-roundfoamed-in PU seal

Surface finishEnclosure and cover. . . Dipcoat-primed

powder-coated on the outsidetextured paint

Colour . . . . . . . . . . . . . . . . . . . RAL 7035Protection categoryWithout gland plate . . IP66 to IEC60529

complies with NEMA 4With gland plate . . . . . IP55 to IEC60529

complies with NEMA 12

Approvals

ULCSA TVGermanischer Lloyd Russian Maritime Register of Shipping Lloyds Register of Shipping Bureau VeritasVDE

Terminal boxes

Includes: KL terminal box with coverQuick action screw including

plastic bushes

Where cable gland plateis included: Sheet steelgland plates with seals

and assembly parts

150 150 80 1.25 1.25 1.4 KL1514.510 18.75

150 150 120 1.25 1.25 1.6 KL1500.510 20.89

200 150 80 1.25 1.25 1.6 KL1528.510 21.31

200 150 120 1.25 1.25 1.8 KL1529.510 22.98

200 200 80 1.25 1.25 1.9 KL1516.510 21.97

200 200 120 1.25 1.25 2.3 KL1502.510 23.69300 150 80 1.25 1.25 2.1 KL1515.510 22.30

300 150 120 1.25 1.25 2.6 KL1501.510 24.36

300 150 120 1.25 1.25 2.7 KL1530.510 31.09

300 200 80 1.25 1.25 2.6 KL1517.510 23.69

300 200 120 1.25 1.25 3.0 KL1503.510 26.31

300 200 120 1.25 1.25 3.3 KL1531.510 33.43

300 300 120 1.38 1.25 4.0 KL1507.510 31.96

300 300 120 1.38 1.25 4.5 KL1535.510 40.23

400 150 120 1.25 1.25 3.2 KL1589.510 28.07

400 200 80 1.25 1.25 3.2 KL1518.510 27.58

400 200 120 1.25 1.25 3.6 KL1504.510 29.72

400 200 120 1.25 1.25 4.0 KL1532.510 36.63

400 300 120 1.38 1.25 4.8 KL1508.510 34.98

400 300 120 1.38 1.25 5.2 KL1536.510 43.44

400 400 120 1.38 1.25 6.2 KL1511.510 42.04

400 400 120 1.38 1.25 6.7 KL1539.510 51.79

500 200 120 1.25 1.25 4.4 KL1505.510 33.15

500 200 120 1.25 1.25 4.9 KL1533.510 42.91

500 300 120 1.38 1.25 5.2 KL1537.510 49.32

500 300 120 1.38 1.25 5.8 KL1509.510 39.20

600 200 80 1.25 1.25 4.6 KL1519.510 35.18

600 200 120 1.25 1.25 5.7 KL1506.510 36.16

600 200 120 1.25 1.25 5.9 KL1534.510 45.72600 300 120 1.38 1.25 6.8 KL1510.510 43.76

600 300 120 1.38 1.25 7.7 KL1538.510 53.88

600 400 120 1.38 1.25 8.4 KL1512.510 49.68

600 400 120 1.38 1.25 9.0 KL1540.510 58.98

800 200 120 1.25 1.25 6.8 KL1527.510 52.83

800 200 120 1.25 1.25 7.2 KL1542.510 59.41

800 400 120 1.38 1.25 11.0 KL1513.510 57.92

800 400 120 1.38 1.25 12.0 KL1541.510 69.76

Dimensions (mm) Material thickness (mm) Weight Cable ListW H D Enclosure Door (kg) Gland Plate Order Code Price

PG style A: 12 x PG13.5 2 5 KL1581.000 34.88

PG style B: 6 x PG13.5, 2 x PG16 and 2 x PG21 2 5 KL1582.000 34.88

Pack ListDescription Size Qty Order Code Price

Plastic cable gland plates with PG knockouts

Plastic cable gland plates withPG knockouts

Style A:12 x PG13.5

PG13.5

PG13.5

PG13.5

PG13.5

PG13.5

PG13.5

PG13.5

PG13.5

PG13.5

PG13.5

PG13.5

PG13.5

Style B:

6 x PG13.5, 2 x PG16 and 2 x PG21

PG13.5 PG13.5

PG13.5

PG21

PG16PG16

PG16

PG21

PG13.5

PG13.5

PG13.5


7/32

Enclosureswww.lcautomation.com


KL Terminal box accessories

Cable retainer (flat) 20 SZ2365.000 33.43Cable retainer (inclined) 20 SZ2366.000 34.52

Cover retainer 3 pairs KL1591.000 12.75

Cover hinges (die-cast zinc) 6 KL1592.000 15.12

Cover hinges (stainless steel) 2 KL1592.010 33.08

Earthing set 5 SZ2570.100 22.59

Spare quick-release fastener 12 KL1593.000 13.99

Wall mounting brackets (8mm wall distance) 4 KL1590.000 4.56

Wall mounting brackets (10mm wall distance) 4 SZ2508.010 11.67

Pack ListDescription Qty Order Code Price

Accessories

150 137 TS 35/7.5 10 SZ2314.000 22.55

200 187 TS 35/7.5 10 SZ2315.000 25.22

300 287 TS 35/7.5 10 SZ2316.000 32.99

400 387 TS 35/7.5 10 SZ2317.000 32.74

500 487 TS 35/15 10 SZ2318.000 44.00

600 587 TS 35/15 10 SZ2319.000 50.40

Enclosure Support Rails Pack ListW (mm) L (mm) Design Qty Order Code Price

2 TS 35/7.5 6 SZ2313.150 64.63

2 TS 35/15 6 SZ2313.750 42.64

Support Rails Pack ListL (m) Design Qty Order Code Price

Support rails (DIN rail)

150 150 KL1560.700 3.75

200 150 KL1575.700 4.47

200 200 KL1562.700 5.01

300 150 KL1561.700 5.01

300 200 KL1563.700 6.18

300 300 KL1567.700 8.47

400 150 KL1576.700 6.48

400 200 KL1564.700 7.75

400 300 KL1568.700 10.60

400 400 KL1571.700 14.92

EnclosureW H List(mm) (mm) Order Code Price

Mounting plates

500 200 KL1565.700 9.59

500 300 KL1569.700 13.47

600 200 KL1566.700 11.48

600 300 KL1570.700 16.51

600 400 KL1572.700 19.53

800 200 KL1574.700 18.36

800 400 KL1573.700 23.98

EnclosureW H List(mm) (mm) Order Code Price

Length sized to enclosure width

Standard 2m length

Plastic cable gland plates with PG knockouts

Mounting plates

Cable retainer

Earthing set

Support rails

Mounting plateFor component installation outside of the

enclosure.Assembly screws included asaccessories with the enclosure.

Support rails (DIN rail)TS 35/7.5 or TS 35/15Supplied in two lengths

Standard 2m orsized to the enclosure width

You may need to order . . .

General accessories

Cable and cover retainers,hinges, earthing set,

spare quick-release fasteners

and wall mounting brackets

1

2

3

1

3

2

The KL range is also available in stainless steel see page 177


8/32



AE Compact enclosures

Technical specificationMaterialEnclosure. . . . . . . . . . . . . . . . Sheet steelDoor . . . . . . . . . . . Sheet steel, all-round

foamed-in PU sealSurface finishEnclosure and door. . . . Dipcoat-primed

powder- coated on the outsidetextured paint

Mounting plate . . . . . . . . . . . Zinc-platedColour . . . . . . . . . . . . . . . . . . . RAL 7035Protection category

IP66 NEMA 4 except certainmodels with double doors

IP 55 NEMA 12

Approvals

ULCSA TVGermanischer Lloyd

Russian Maritime Register of Shipping Lloyds Register of Shipping Bureau VeritasVDE

Includes:AE compact enclosureGland plate(s) in enclosure baseCam lock or 3-point lock

Mounting plate Single door enclosures include an

interchangeable door hinge(except AE1032.500 and AE1035.500)

200 300 120 1 1 4.0 162 275 AE1032.500 33.94

200 300 155 1 1 4.5 162 275 AE1035.500 39.47

300 300 155 1 1 6.1 254 275 AE1036.500 44.23300 300 210 1 1 7.0 254 275 AE1033.500 49.85

300 400 210 1 1 8.8 254 375 AE1034.500 54.34

380 300 155 1 1 7.4 334 275 AE1030.500 45.65

380 300 210 1 1 7.5 334 275 AE1031.500 51.66

380 380 210 1 1 9.8 334 355 AE1380.500 55.42

380 600 210 2 1 15.6 334 570 AE1038.500 65.54

380 600 350 2 1 19.4 334 570 AE1338.500 109.23

400 500 210 2 1 13.0 354 475 AE1045.500 64.23

400 800 300 2 1 26.2 349 770 AE1037.500 128.15

500 500 210 2 1 16.8 449 470 AE1050.500 78.60

500 500 300 2 1 19.6 449 470 AE1350.500 101.42

500 700 250 2 1 31.2 449 670 AE1057.500 112.22

600 380 210 1 1 15.4 549 355 AE1039.500 73.35600 380 350 1 1 20.0 549 355 AE1339.500 120.59

600 600 210 2 1 22.8 549 570 AE1060.500 88.09

600 600 250 2 1 24.8 549 570 AE1054.500 111.29

600 600 350 2 1 28.4 549 570 AE1360.500 131.35

600 760 210 2 1 32.1 549 730 AE1076.500 107.00

600 760 350 2 1 36.0 549 730 AE1376.500 155.31

600 800 250 2 1 33.6 549 770 AE1058.500 135.20

600 1000 250 2 1 50.5 539 955 AE1090.500 152.33

600 1200 300 1 55.0 540 1155 AE1260.500 184.62

760 760 210 2 1 40.0 704 730 AE1077.500 140.35

760 760 300 2 1 44.5 704 730 AE1073.500 164.57

800 600 300 2 1 33.9 749 570 AE1055.500 155.12

800 1000 300 2 1 57.0 739 955 AE1180.500 181.41800 1200 300 1 70.0 740 1155 AE1280.500 211.65

1000 760 210 2 2 52.0 730 944 AE1100.500 207.76

1000 760 300 2 2 56.0 730 944 AE1130.500 208.18

1000 1000 300 2 2 71.0 939 955 AE1110.500 237.27

1000 1200 300 2 85.0 940 1155 AE1213.500 280.57

1000 1400 300 2 97.0 940 1355 AE1114.500 356.51

No. of 3-point MountingDimensions (mm) Cam Lock No. of Weight Plate (mm) List

W H D Locks System Doors (kg) W H Order Code Price

Enclosures

The AE range is also available in stainless steel see page 178

Includes

mountingplate


9/32



600 300 279 SO2816.200 45.93

800 300 279 SO2818.200 48.26

1000 300 279 SO2801.200 44.91

Enclosure PlinthW D D Order List(mm) (mm) (mm) Code Price

600 300 279 SO2826.200 58.62

800 300 279 SO2828.200 65.02

1000 300 279 SO2802.200 80.63

Enclosure PlinthW D D Order List(mm) (mm) (mm) Code Price

Base/plinth, complete (RAL 7022)

AE Compact enclosure accessories

Plastic handle (inc. 2 keys - 3524E) SZ2576.000 16.34

T-handle die-cast zinc, chrome-plated (inc. 2 keys - 3524E) SZ2575.000 25.69

ListDescription Order Code Price

Handles (Version B)

380 210 SZ2501.500 48.66

600 210 SZ2502.500 61.56

600 350 SZ2511.500 66.03

EnclosureW D List

(mm) (mm) Order Code Price

Rain canopy

100mm high 200mm high

210 4 SZ2383.210 19.78

250 4 SZ2383.250 24.73300 4 SZ2383.300 24.54

350 4 SZ2383.350 34.19

Enclosure Pack ListD (mm) Qty Order Code Price

Rails for interior installation

M6 10 200 10 SZ2412.210 32.38

M8 16 200 10 SZ2412.216 36.45

M8 25 200 10 SZ2412.225 37.71

M6 10 300 10 SZ2412.310 46.46

M8 16 300 10 SZ2412.316 60.79

M8 25 300 10 SZ2412.325 70.17

Cross section Length Pack List

Connection mm2

(mm) Qty Order Code Price

Earthing straps

M12 x 1.5 3-7 15 Brass SZ2411.800 17.52

M16 x 1.5 4.5-10 15 Brass SZ2411.810 21.19

M20 x 1.5 7-13 10 Brass SZ2411.820 17.52

M25 x 1.5 10-17 10 Brass SZ2411.830 22.36

M32 x 1.5 13-21 5 Brass SZ2411.840 17.69

M40 x 1.5 19-28 4 Brass SZ2411.850 22.36

M50 x 1.5 25-35 2 Brass SZ2411.860 18.51

M63 x 1.5 35-48 1 Brass SZ2411.870 18.88

Cable Pack ListSize Diameter (mm) Qty Material Order Code Price

Cable glands

Baying kit 1 set SZ1199.100 25.67

Door stay 5 SZ2519.000 31.26

180 hinges 2 SZ2449.000 17.35

Eyebolts 4 SZ2509.000 21.65

Wall mounting bracket for external mounting 4 SZ2508.100 10.75


Accessories

Base/plinth Interior rails

Handles (version B)Cable glands

Base/plinth (complete)

100mm or 200mm high

Trim panels at the front and rear withfitted corner pieces and side trim panels

(Includes assembly parts)

Rails for interiorinstallation

For mounting in the enclosure(no machining required). Suitable for

all-round mounting on the sides, baseand roof areas. Variable with 2 rows of

system punchings.


Rain canopy

Reliable protection for outdoor sitingwith water run-off to the rear.

Easily retro-fitted(Includes assembly parts)

1

3

HandlesAvailable in plastic (RAL 9011) or

T-handle in die-cast zinc, chrome plated.(Includes two keys, assembly parts & seals)

4

Earthing strapsEarthing straps counteract the current

displacement effect at high frequencies,whilst at the same time offering highly

flexible connection opportunities.Tin-plated copper, available in various

lengths and cross sections withpress fitted contact rings.

5

Cable glandsSupplied in brass with nickel platedsurface finish and neoprene seal.

The clamping membrane is designed foreven tightening and strain relief whichprotects the cables. Insulation is via a

plastic insert with optimum seal on theconnection thread, due to the O-ring.

6

AccessoriesBaying kit, door stay,180 hinges, eyebolts,

wall mounting brackets forexternal mounting

7

2

1

32

4

5

6

7

3


10/32



600 800 400 1 540 755 CM5110.500 174.48

600 1000 400 1 540 955 CM5111.500 211.37

600 1200 300 1 540 1155 CM5112.500 199.20

600 1200 400 1 540 1155 CM5113.500 236.92

800 1000 300 1 740 955 CM5114.500 184.49

800 1000 400 1 740 955 CM5115.500 250.72

800 1200 300 1 740 1155 CM5116.500 228.64

800 1200 400 1 740 1155 CM5117.500 294.26

1000 1000 300 2 940 955 CM5118.500 244.24

1000 1200 300 2 940 1155 CM5119.500 300.60

1000 1200 400 2 940 1155 CM5120.500 350.34

1000 1400 300 2 940 1355 CM5121.500 361.81

1000 1400 400 2 940 1355 CM5122.500 444.86

1200 1200 400 2 1140 1155 CM5123.500 389.59

Dimensions (mm) No. of Mounting Plate (mm) ListW H D Doors W H Order Code Price

CM Compact system enclosures

Enclosures

Gland plates

300 600 1-piece 1 1 CM5001.218 9.12

300 800 1-piece 1 1 CM5001.219 11.40

300 1000 2-piece 1 2 CM5001.220 8.49

300 1200 2-piece 1 2 CM5001.221 10.15

400 600 1-piece 1 1 CM5001.222 8.49

400 800 1-piece 1 1 CM5001.223 10.97

400 1000 2-piece 1 2 CM5001.224 11.61

400 1200 2-piece 1 2 CM5001.225 9.55

Enclosure Base Pack Packs List

D (mm) W (mm) Opening Qty Required Order Code Price

600 1 set TS8601.600 26.23

800 1 set TS8601.800 27.09

1000 1 set TS8601.000 35.21

1200 1 set TS8601.200 35.97

Enclosure Pack ListW (mm) Qty Order Code Price

100mm high

Base/plinth components, front and rear(RAL 7022)

Set = 2 base/plinth components, 4 cover caps, 4 screws and captive nuts M12 for mounting on the enclosure

600 1 set TS8602.600 42.36

800 1 set TS8602.800 52.09

1000 1 set TS8602.000 67.05

1200 1 set TS8602.200 72.73


200mm high


MaterialEnclosure . . . . . . . Sheet steel, 1.5mmDoor. . . . . . . . . . . Sheet steel, 2.0mm

all-round foamed-in PU seal

Mounting plate . . . Sheet steel, 3.0mmSurface finish

Enclosure and door. . . Dipcoat-primedpowder coated on the outside,

textured paintMounting plate . . . . . . . . . Zinc plated

Colour . . . . . . . . . . . . . . . . . . RAL 7035Protection category. . . IP55 to IEC60529

complies with NEMA 12 providedsuitable gland plates are selected

Approvals

ULCSA TV Lloyds Register of Shipping

Includes:CM compact system enclosure Single door enclosures include an

interchangeable door hinge

3-point lockMounting plate

Please rememberto order your

gland plates or trim panels!For more information on heating and cooling options

contact the sales office on 01254 685900

1

2

Includesmounting

plate


11/32



100mm high

300 1 set TS8601.030 13.05

400 1 set TS8601.040 14.77


Base/plinth side trim panels (RAL 7022)

Set = 2 base/plinth side trim panels including parts for attaching to the base/plinth components

200mm high

300 1 set TS8602.030 19.63

400 1 set TS8602.040 20.59


CM Compact system enclosure accessories

400 2 CM5001.370 19.12

300 2 CM5001.371 16.38

Enclosure Pack ListD (mm) Quantity Order Code Price


300 4 TS8612.130 23.70

400 4 TS8612.140 34.27

500 4 TS8612.150 37.48600 4 TS8612.160 44.18

800 4 TS8612.180 49.01

1000 4 TS8612.100 67.44

1200 4 TS8612.120 77.26

Enclosure Pack ListD(mm) Quantity Order Code Price

Enclosure Pack ListW/D (mm) Qty Order Code Price

TS punched section with17 x 73mm mounting flange

Base configuration rail

600 4 CM5001.050 22.79

800 4 CM5001.051 27.53

1000 4 CM5001.052 32.291200 4 CM5001.053 33.67

1400 4 CM5001.054 38.00


Enclosure Pack ListW(mm) Qty Order Code Price

Rail for interior installation

For height/width

400 90 255 210 TS4114.000 20.27

500 35 355 210 TS4115.500 18.88

500 90 355 210 TS4115.000 23.45600 35 455 210 TS4116.500 20.24

600 90 455 210 TS4116.000 24.05

800 35 655 210 TS4118.500 22.95

800 90 655 210 TS4118.000 27.87

To fit door Clearance opening ListW (mm) D (mm) W (mm) H (mm) Order Code Price

Sheet steel wiring plan pockets

400 290 20 TS4594.000 36.26

500 390 20 TS4309.000 45.19

600 490 20 TS4596.000 53.76

800 690 20 TS4598.000 61.25

900 790 20 TS4579.000 65.79

1000 890 20 TS4599.000 71.94

Door L Pack Order ListW(mm) (mm) Qty Code Price


600 499 1 CM5001.080 9.05

800 699 1 CM5001.081 9.65

1000 899 1 CM5001.082 10.12

1200 1099 1 CM5001.083 10.75

Enclosure L Pack Order ListW(mm) (mm) Qty Code Price

Cable clamp rails forstrain relief

600 400 CM5001.310 68.48

800 400 CM5001.330 73.93

1000 400 CM5001.350 79.36

1200 400 CM5001.360 86.06

EnclosureW D List


Rain canopy

4

5

6

7

8

9

10

3

Gland platesSheet steel with zinc-plated surface

finish. Available in 1 or 2 pieces,suitable for cable glands(Includes assembly parts)


1

Cable clamp railsFor strain relief with cable entry. The

length of the cable clamp rail is tailoredto the width of the mounting plate.(Includes two mounting brackets and

assembly screws)

6

Base configuration railFor mounting in the enclosure depth

using the existing threaded bolts,no machining required.

TS system punchings on two sides.Creates additional installation options.


7

Base/plinth components

Front and rear

100mm or 200mm highPre-configured with corner pieces.

Sized to suit enclosure width

Base/plinthSide trim panels

100mm or 200mm high

For mounting between the front andrear base/plinth components.

2

3

Interior railsFor mounting in the enclosure

(no machining required). Suitable forall-round mounting on the sides, baseand roof areas. Variable with 2 rows of

system punchings.

4

Support strips for doorUsed for attaching cable ducts, cableconduit holders etc. 4.5mm diameterhole on a 25mm DIN pitch pattern.

(Includes screws)

5

TS punched sectionwith 17 x 73mm mounting flange

For outer/inner mounting levelVariable, with 5 rows of holes for

universal skeleton structures or partialassembly. Simply locate into the

TS punchings and secure.(Includes assembly screws)

8

Wiring plan pocketsFor fastening to tubular door frames atany height. (Includes assembly screws)

10

Rain canopyReliable protection for outdoor siting

with water run-off to the rear.(Includes assembly parts)

9


12/32



SE8 Enclosure system

Technical specificationMaterialEnclosure . . . . . . . . Sheet steel, 1.5mmDoor. . . . . . . . . . . . Sheet steel, 2.0mmRear panel andgland plates . . . . . Sheet steel, 1.5mm

Mounting plate . . . . Sheet steel, 3.0mmSurface finishEnclosure, door/double door

and rear panel . . . . . . Dipcoat-primedpowder-coated on the outside

textured paintMounting plate andgland plates . . . . . . . . . . . . Zinc-plated

Colour . . . . . . . . . . . . . . . . . . RAL 7035Protection category. . IP55 to IEC 60529


600 1800 400 499 1696 1 SE5830.500 424.95

800 1800 400 699 1696 1 SE5831.500 471.61800 2000 400 699 1896 1 SE5832.500 504.84

800 2000 500 699 1896 1 SE5833.500 532.41

800 2000 600 699 1896 1 SE5834.500 548.68

1000 1800 400 899 1696 2 SE5840.500 593.19

1200 1800 400 1099 1696 2 SE5841.500 615.30

1200 2000 400 1099 1896 2 SE5843.500 714.05

1200 2000 500 1099 1896 2 SE5844.500 732.82

1200 2000 600 1099 1896 2 SE5845.500 752.88

1600 1800 400 1499 1696 2 SE5842.500 799.53

1800 2000 500 1699 1896 2 SE5846.500 1,031.65

Dimensions (mm) Mounting Plate (mm) No. of W H D W H Doors Order Code List Price

Enclosures

Includes: SE8 enclosure system with double-bit

lock insert Single door enclosures include an

interchangeable door hingeMounting plateGland plates Rear panel (in two pieces from a

width of 1600mm)Detachable rear panel

100mm plinth

600 1 set TS8601.600 26.23

800 1 set TS8601.800 27.09

1000 1 set TS8601.000 35.21

1200 1 set TS8601.200 35.97

1600 1 set TS8601.920 38.76

1800 1 set TS8601.980 50.17


400 1 set TS8601.040 14.77

500 1 set TS8601.050 16.02

600 1 set TS8601.060 17.98


100mm plinth

Components front and rear (RAL 7022)

Side trim panels (RAL 7022)



200mm plinth

600 1 set TS8602.600 42.36

800 1 set TS8602.800 52.09

1000 1 set TS8602.000 67.05

1200 1 set TS8602.200 72.73

1600 1 set TS8602.920 90.56

1800 1 set TS8602.980 103.34


400 1 set TS8602.040 20.59

500 1 set TS8602.050 22.86

600 1 set TS8602.060 24.72


200mm plinth

400 4 TS8612.040 34.76

500 4 TS8612.050 37.93

600 4 TS8612.060 44.63



400 4 TS8612.140 34.27

500 4 TS8612.150 37.48

600 4 TS8612.160 44.18

Enclosure Pack ListD (mm) Quantity Order Code PriceEnclosure Pack ListD (mm) Qty Or der Code Price

TS punched section with mounting flange

For inner mounting levelFor outer mounting level

1

2

3

The SE8 range is also

available in stainless steel

see pages 182-183

Includesmounting

plate


13/32

. . . for our range of

Hygienic designenclosuresand accessories



SE8 Enclosure system accessories

4 PS4568.000 16.32

Pack ListQuantity Order Code Price

Roof eyebolts

600 2 TS8800.060 26.34

800 2 TS8800.080 33.56

1000 4 TS8800.100 39.21

1200 4 TS8800.120 53.17


Base cable entry plate

600 2 PS4191.000 33.29

800 2 PS4192.000 34.61

1000 2 PS4336.000 42.62

1200 2 PS4196.000 42.52

1600 2 PS4338.000 61.03

1800 2 PS4339.000 65.49


Cable clamp rails

suitable for use in the

food & beverage and

pharmaceutical industries

Punched section withmounting flange

Roof eyebolts

Base cable entry plate

6-12 25 SZ2350.000 39.59

12-16 25 SZ2351.000 41.31

14-18 25 SZ2352.000 42.64

18-22 25 SZ2353.000 44.08

22-26 25 SZ2354.000 46.66

26-30 25 SZ2355.000 50.49

30-34 25 SZ2356.000 54.74

34-38 25 SZ2357.000 57.15

38-42 25 SZ2358.000 59.44

42-46 25 SZ2359.000 62.50

46-50 25 SZ2360.000 64.04

Cable Pack List (mm) Qty Order Code Price

Cable clamps


Base/plinth componentsFront and rear




100mm or 200mm high

For mounting between the front andrear base/plinth components.

1

4 5

6

7

2

TS punched sectionwith 17 x 73mm mounting flange


universal skeleton structures or partialassembly. Simply locate into the

TS punchings and secure.(Includes assembly screws)

3

Cable clamp railsFor strain relief with cable entry. Depthvariable mounting on a 25mm pitchpattern on the horizontal enclosure

section or in side base/plinth trim panels.(Includes assembly parts)

4

Cable clamps(For cable clamp rails)

Used for fastening the cables to the cableclamp rails. Sheet steel with zinc-plated

surface finish.(Includes plastic insert)

5

Roof eyeboltsUsed for crane transportation of

enclosures. Thread M12.

6

Base cable entry platesSuitable for cable entry grommetsand connector grommets instead

of segments of the standarddivided gland plates.


7

See pages 184-185


14/32



TS8 Baying enclosures

Technical specificationMaterialEnclosure frame, roof, rear panel

and gland plates. . Sheet steel, 1.5 mmDoor. . . . . . . . . . . Sheet steel, 2.0 mmMounting plate . . . Sheet steel, 3.0 mm

Surface finishEnclosure frame. . . . . . Dipcoat-primedDoor, roof and rear panel. . . . . . Dipcoat-primed powder coated

on the outside, textured paintMounting plate andgland plates . . . . . . . . . . . . Zinc plated

Colour . . . . . . . . . . . . . . . . . . RAL 7035Protection category. . IP55 to IEC60529


ApprovalsUL

CSA TV Russian Maritime Register of Shipping TV Mark Lloyds Register of Shipping Bureau VeritasVDEGermanischer Lloyd

Includes: TS8 baying enclosure 3mm double-bit lock insertGland plates

Mounting plates*

Rear panel (back plate) Roof plate 4 eyebolts

400 1800 500 49.2 1 TS8485.510 279.40

400 1800 600 51.7 1 TS8486.510 298.70

400 2000 500 60.7 1 TS8405.510 294.79

400 2000 600 55.7 1 TS8406.510 309.07

600 1200 500 499 1096 74.5 1 TS8615.500 366.19

600 1400 500 499 1296 86.0 1 TS8645.500 374.74600 1600 500 499 1496 100.0 1 TS8665.500 429.31

600 1800 400 499 1696 91.3 1 TS8684.500 370.90

600 1800 500 499 1696 93.8 1 TS8685.500 404.78

600 1800 600 499 1696 96.8 1 TS8686.500 443.08

600 2000 400 499 1896 99.0 1 TS8604.500 401.54

600 2000 500 499 1896 101.3 1 TS8605.500 430.09

600 2000 600 499 1896 104.0 1 TS8606.500 450.63

600 2000 800 499 1896 111.3 1 TS8608.500 499.04

600 2200 600 499 2096 113.1 1 TS8626.500 479.05

800 1200 500 699 1096 92.1 1 TS8815.500 396.81

800 1400 500 699 1296 107.5 1 TS8845.500 404.78

800 1600 500 699 1496 103.0 1 TS8865.500 463.84

800 1800 400 699 1696 113.5 1 TS8884.500 422.11

800 1800 500 699 1696 115.8 1 TS8885.500 436.59

800 1800 500 699 1696 122.5 2 TS8880.500 488.01

800 1800 600 699 1696 120.3 1 TS8886.500 487.30

800 1800 600 699 1696 125.8 2 TS8881.500 518.06

800 2000 400 699 1896 124.0 1 TS8804.500 450.63

800 2000 500 699 1896 126.3 1 TS8805.500 460.36

800 2000 600 699 1896 130.5 1 TS8806.500 471.50

800 2000 800 699 1896 137.0 1 TS8808.500 541.89

800 2200 600 699 2096 139.3 1 TS8826.500 514.42

1000 1800 400 899 1696 136.4 1 TS8084.500 519.841000 1800 400 899 1696 140.0 2 TS8080.500 578.40

1000 2000 400 899 1896 152.8 2 TS8004.500 596.05

1000 2000 500 899 1896 157.1 2 TS8005.500 602.20

1000 2000 600 899 1896 161.2 2 TS8006.500 626.61

1200 1200 500 1099 1096 140.0 2 TS8215.500 557.93

1200 1400 500 1099 1296 163.5 2 TS8245.500 571.45

1200 1600 500 1099 1496 159.3 2 TS8265.500 660.51

1200 1800 400 1099 1696 170.6 2 TS8284.500 563.53

1200 1800 500 1099 1696 173.3 2 TS8285.500 610.97

1200 1800 600 1099 1696 179.9 2 TS8286.500 684.11

1200 2000 400 1099 1896 184.5 2 TS8204.500 645.05

1200 2000 500 1099 1896 190.6 2 TS8205.500 655.72

1200 2000 600 1099 1896 194.6 2 TS8206.500 668.13

1200 2000 800 1099 1896 203.0 2 TS8208.500 778.40

1200 2200 600 1099 2096 208.0 2 TS8226.500 747.25

Dimensions (mm) Mounting Plate (mm) Weight No. of Support ListW H D W H (kg) Doors Strips fitted Order Code Price

Enclosures

*Except 400mm wide enclosuresWithout tubular door frame, mounting plate and gland plates. Protection category IP55 and NEMA 12 are not met.

The TS range is also

available in stainless steel

see pages 180-181

Includesmounting

plate


15/32



1800 1 TS8614.180 154.64

2000 1 TS8614.200 164.73

Fixing kit 4 bolt kits 505063 27.56

Enclosure Pack ListH (mm) Qty Order Code Price

Mounting plates(For 400mm wide enclosures)

100mm high

400 1 set TS8601.400 24.16

600 1 set TS8601.600 26.23

800 1 set TS8601.800 27.09

1000 1 set TS8601.000 35.21

1200 1 set TS8601.200 35.97


400 1 set TS8601.040 14.77

500 1 set TS8601.050 16.02

600 1 set TS8601.060 17.98

800 1 set TS8601.080 23.81


400 1 set TS8602.040 20.59

500 1 set TS8602.050 22.86

600 1 set TS8602.060 24.72

800 1 set TS8602.080 35.21


400 1 set TS8602.400 40.01

600 1 set TS8602.600 42.36

800 1 set TS8602.800 52.09

1000 1 set TS8602.000 67.05

1200 1 set TS8602.200 72.73


100mm high

Base/plinth components, front and rear (RAL 7022)

Base/plinth side trim panels (RAL 7022)

Set = 2 base/plinth side trim panels including parts for attaching to the base/plinth components


200mm high

200mm high

400 1 TS8800.845 8.96

500 1 TS8800.855 9.81

600 1 TS8800.865 10.78

800 1 TS8800.885 12.45


Baying cover top

1800 TS4590.700 48.39

2000 TS4591.700 47.15

2200 TS4592.700 56.58

Enclosure ListH (mm) Order Code Price

Mounting plate infill

continued on next page

TS8 Baying enclosure accessories

1200 500 2 TS8115.235 77.26

1400 500 2 TS8145.235 79.85

1600 500 2 TS8165.235 88.28

1800 400 2 TS8184.235 84.98

1800 500 2 TS8185.235 96.96

1800 600 2 TS8186.235 107.49

2000 400 2 TS8104.235 85.51

2000 500 2 TS8105.235 98.14

2000 600 2 TS8106.235 102.77

2000 800 2 TS8108.235 126.90

2200 600 2 TS8126.235 115.02

H D Pack Order List(mm) (mm) Qty Code Price

Side panels

Mounting platesRequired for

400mm wide enclosures

+ Fixing kit (4 bolt kits)

Mounting plate infillFor continuous mounting surface

in bayed sites where themounting plate is set forward


Side panelsScrew-fastened, sheet steel withautomatic potential equalisation



Base/plinth components

Front and rear100mm or 200mm high

Pre-configured with corner pieces.Sized to suit enclosure width


100mm or 200mm high

For mounting between the front andrear base/plinth components.Sized to suit enclosure depth

Baying cover top

for bayed enclosuresA cover with two end caps which can be

clipped over the seal between the twoenclosures, preventing dirt and liquidfrom collecting on the baying seal

TS punched sectionwith 17 x 73mm mounting flangeFor outer/inner mounting level

Variable, with 5 rows of holes foruniversal skeleton structures or partial

assembly. Simply locate into theTS punchings and secure.(Includes assembly screws)

Sheet steelwiring plan pockets

For fastening to tubular door frames atany height. (Includes assembly screws)

Divider panelsFor shielding individual enclosure cells.The divider panel may also be fitted at

the rear. (Includes assembly parts)

General accessories

Hinges, brackets,clamps, door stays etc

1

2

3

4

5

7

1800 400 TS8609.840 46.80

1800 500 TS8609.850 55.55

1800 600 TS8609.860 64.10

2000 400 TS8609.040 58.63

2000 500 TS8609.050 64.10

2000 600 TS8609.060 70.132000 800 TS8609.080 81.57

2200 600 TS8609.260 75.76

Enclosure ListH (mm) D (mm) Order Code Price

Divider panels6

1

3

4

5

7

8

6

9

10

2


16/32



TS8 Baying enclosure accessories (continued)

400 4 TS8612.040 34.76

500 4 TS8612.050 37.93

600 4 TS8612.060 44.63

800 4 TS8612.080 49.42

1000 4 TS8612.000 67.83

1200 4 TS8612.020 77.65


EnclosureW or D Pack List


400 4 TS8612.140 34.27

500 4 TS8612.150 37.48

600 4 TS8612.160 44.18

800 4 TS8612.180 49.01

1000 4 TS8612.100 67.44

1200 4 TS8612.120 77.26

Enclosure Pack ListD (mm) QuantityOrder Code Price

EnclosureW or D Pack List


TS punched section with 17 x 73mm mounting flange


Mounting plate fixing kit 4 bolt kits 505063 27.56

Door stay (bottom assembly) 5 TS4583.000 33.52

180 hinges 4 TS8800.190 34.69

Wiring plan lectern for door 1 TS4120.000 34.22

Combination angle, lifting eye for bayed enclosures 4 TS4540.000 21.17

Baying brackets 4 TS4582.500 19.54

Baying clamp, vertical 6 TS8800.410 10.48

Angular baying brackets 4 TS8800.430 11.52

Quick fit baying clamp 6 TS8800.500 10.75


Accessories

400 90 255 210 TS4114.000 20.27

600 35 455 210 TS4116.500 20.24

600 90 455 210 TS4116.000 24.05

800 35 655 210 TS4118.500 22.95

800 90 655 210 TS4118.000 27.87

1000 90 855 210 TS4124.000 32.76

To fit door Plan pocket Clearance opening ListW (mm) D (mm) W (mm) H (mm) Order Code Price

Sheet steel wiring plan pockets

TS punched section

with mounting flangeBaying cover top for

bayed enclosures

Side panelsMounting plates

Sheet steel wiringplan pockets

180 hinges

Baying

brackets

Baying

brackets

Angularbaying

brackets

8

9

1

3

4

5

6

10

10

Does the Rittal TS range ofenclosures include a back plate?

Yes, Rittal call the back plate amounting plate and it is shippedinside the enclosure.

Frequently Asked Question

TechnicalSupport

Ordering Example

Requirements:

Enclosure1000 x 2000 x 500mm (w x h x d)

+ Mounting plates

+ Side panels

+ 200mm front and rearplinth

+ Side trim panels+ Divider panel

+ Door stay

Parts order:

Enclosure TS8005.500 602.20

Mounting plates Included with enclosure

Side panels TS8105.235 98.14

Front and rear plinth TS8602.000 67.05

Side trim panels TS8602.050 22.86

Divider panel TS8609.050 64.10

Door stay TS4583.000 33.52

TOTAL ORDER = 887.87


17/32



Material: Sheet steel, 2mm

150 137 TS 35/7.5 10 SZ2314.000 22.55

200 187 TS 35/7.5 10 SZ2315.000 25.22

300 287 TS 35/7.5 10 SZ2316.000 32.99

400 387 TS 35/7.5 10 SZ2317.000 32.74


Support rails (DIN rail) Length sized to enclosure width

KL Stainless steel terminal boxes


MaterialEnclosure. . . . . . . . . . . . . . Stainless steel

1.4301 (AISI 304), 1.25mmCover. . . . . . . . . . . . . . . . .Stainless steel

1.4301 (AISI 304), 1.25mm,all-round foamed-in PU seal

Surface finishEnclosure and cover. . . . . . . . . Brushed,

grain size 240 or 180

Protection category. . . IP66 to IEC60529complies with NEMA 4X

Approvals

UL

CSA TVGermanischer Lloyd Russian Maritime Register of Shipping Lloyds Register of Shipping Bureau VeritasVDE

Terminal boxes

150 150 80 1.3 4 KL1521.010 82.54

150 150 120 1.6 4 KL1527.010 101.18

200 200 80 1.8 4 KL1523.010 98.09

200 200 120 2.2 4 KL1528.010 118.23

300 150 80 1.8 4 KL1522.010 99.58

300 200 80 2.4 4 KL1524.010 113.73

300 200 120 2.9 4 KL1529.010 142.93

300 300 120 3.9 4 KL1526.010 139.07

400 200 120 3.6 4 KL1525.010 129.36

400 300 120 4.6 4 KL1530.010 165.27

No. ofDimensions (mm) Weight Quick-release List

W H D (kg) Fasteners Order Code Price

150 150 KL1560.700 3.75

200 200 KL1562.700 5.01

300 150 KL1561.700 5.01

300 200 KL1563.700 6.18

300 300 KL1567.700 8.47400 200 KL1564.700 7.75

400 300 KL1568.700 10.60

EnclosureW H List


Mounting plates

Wall mounting bracket Stainless steel 4 KL1594.000 18.96

Wall angle Stainless steel 4 SZ2583.010 16.08

Pole clamp Sheet steel 1 SZ2584.000 55.73

Cover hinges Stainless steel 2 KL1592.010 33.08

Pressure relief stoppers Polyamide 5 SZ2459.500 16.02

Pack ListDescription Material Qty Order Code Price

Accessories

The KL range is also available in sheet steel

see pages 166-167

Mounting plateFor component installation outside of theenclosure.Assembly screws included as

accessories with the enclosure.

Support rails (DIN rail)TS 35/7.5 or TS 35/15Supplied in two lengths

Standard 2m orsized to the enclosure width


General accessories

Wall mounting brackets,wall angle, pole clamp,

cover hinges andpressure relief stoppers

1

3

2

1

2

3


18/32



AE Stainless steel compact enclosures

Technical specificationMaterialEnclosure. . . . . . . . . . . . . . Stainless steelDoor . . . . . . . . . Stainless steel, all-round

foamed-in PU sealMounting plate . . . . . . . . . . . Sheet steelLocks . . . . . . . . . . . . . . . . . Die-cast zinc

Surface finish

Enclosure and door. . Brushed grain 240Mounting plate . . . . . . . . . . . Zinc-platedLocks . . . . . . . . . . . . . . . . . Nickel-plated

Protection category200-800mm . . . . . . IP66 to IEC 60529,

complies with NEMA 4X1000mm . . . . . . . . . IP55 to IEC 60529,


ApprovalsULCSA

TVGermanischer Lloyd Russian Maritime Register of Shipping Lloyds Register of Shipping Bureau VeritasVDE

Includes:AE stainless steel compact enclosure

Cam lock or 3-point lock (forAE 1017.600 and AE1019.600)with double bit insertMounting plate

200 155 SZ2470.000 48.61

300 210 SZ2361.000 57.69

380 155 SZ2471.000 58.06

380 210 SZ2472.000 56.42

500 210 SZ2362.000 58.98

600 210 SZ2473.000 60.87

760 300 SZ2474.000 81.17

800 300 SZ2475.000 82.54

1000 300 SZ2363.000 108.26

EnclosureW D List


Rain canopy

210 4 SZ2383.210 19.78

300 4 SZ2383.300 24.54



Standard 1 SZ2304.000 24.88

Hygienic 1 HD2304.010 32.50

Pack ListType Qty Order Code Price

Cam lock

Wall angle Stainless steel 4 SZ2583.010 16.08

Pole clamp Sheet steel 1 SZ2584.000 55.73

Wall mounting brackets Stainless steel 1.4301 (AISI 304) 4 SZ2433.000 23.68

Wall mounting brackets Stainless steel 1.4404 (AISI 316L) 4 SZ2433.500 24.22

Pack List

Description Material Qty Order Code Price

Accessories

200 300 120 1 1 3.6 162 275 AE1001.600 105.90

200 300 155 1 1 4.1 162 275 AE1002.600 122.54

300 300 210 1 1 6.9 254 275 AE1003.600 133.77

300 380 210 1 1 8.4 275 334 AE1005.600 151.00

380 300 155 1 1 7.4 334 275 AE1004.600 141.81

380 300 210 1 1 8.4 334 275 AE1011.600 144.91

380 380 210 1 1 9.8 334 355 AE1006.600 166.28

380 600 210 1 1 15.1 334 570 AE1008.600 208.32

400 500 210 1 1 12.9 354 475 AE1015.600 195.10

500 500 210 1 1 15.7 449 470 AE1007.600 218.37

500 500 300 1 1 18.4 449 470 AE1013.600 256.93

600 380 210 1 1 14.6 549 355 AE1009.600 207.72

600 600 210 1 1 23.5 549 570 AE1010.600 267.04

600 760 210 1 1 30.2 549 730 AE1012.600 309.30760 760 300 1 1 42.5 704 730 AE1014.600 443.12

800 1000 300 1 1 52.9 739 955 AE1016.600 501.72

800 1200 300 1 61.5 740 1155 AE1017.600 577.24

1000 1000 300 2 2 71.0 939 955 AE1018.600 642.07

1000 1200 300 2 76.0 940 1155 AE1019.600 695.90

No. of 3-point MountingDimensions (mm) Cam Lock No. of Weight Plate (mm) List

W H D Locks System Doors (kg) W H Order Code Price

Enclosures

Material: Stainless steel 1.4301 (AISI 304)


Material: Sheet steel, zinc-plated

Material: Stainless steel

The AE range is also

available in sheet steel

see pages 168-169

Rails for interiorinstallation

For mounting in the enclosure(no machining required). Suitable for

all-round mounting on the sides, baseand roof areas. Variable with 2 rows of

system punchings.

Rain canopyReliable protection for outdoor siting

with water run-off to the rear.Easily retro-fitted



Cam locksStandard stainless steel version (made

entirely from stainless steel) or thehygienic version for easy, safe cleaning

1

1 2

3

43

Accessories

Wall angle, pole clamp andwall mounting brackets

4

2

Includesmounting

plate


19/32



Command panel housing with door Stainless steel


MaterialEnclosure and door. . . . . . Stainless steel

1.4301 (AISI 304)

Handle strips . . . . . . Plastic approved foruse with foodstuffs

Surface finish . . . . . . . . Brushed grain 240Handle strips colour. Similar to RAL 5002Protection category . . IP66 to IEC 60529

Includes: Stainless steel command panel

housing with doorCut-out and reinforcement for

support arm system Fastener with guide plateDoor with sealing frame and side

handle strips 3mm double-bit lock insert The support arm connection and

door hinge may be swapped over byrotating the enclosure

300 300 150 6.3 CP6535.010 273.76

400 300 150 7.5 CP6536.010 291.47

400 400 150 8.8 CP6538.010 328.11

600 400 150 12.1 CP6539.010 351.69

Dimensions (mm) Weight ListW H D kg Order Code Price

Command panel housing with door

Mounting plate for CP6535.010 0271926 16.33




List

Description Order Code Price

Mounting plates

ApprovalsUL cUL

300 287 TS 35/7.5 10 SZ2316.000 32.99

400 387 TS 35/7.5 10 SZ2317.000 32.74


Support railsLength sized to enclosure width

1 Supplied with 2 keys, lock no. 3524E

Die-cast zinc 3mm double-bit lock inserts 41mm SZ2483.000 2.73

Plastic handles with lock cylinder insert SZ2485.000 13.60

Plastic handles without lock insert SZ2485.100 10.84

T handles with lock cylinder insert1 SZ2535.000 25.25

T handles without lock insert SZ2536.000 12.46

ListDescription Length Order Code Price

Alternative lock systems


Material: Sheet steel

. . . for stainless steel

Arm systems

See page 192


20/32



1800 400 2 TS8700.840 207.83

1800 500 2 TS8700.850 235.11

2000 600 2 TS8700.060 294.99

Enclosure Enclosure Pack ListHeight (mm) Depth (mm) Qty Order Code Price

TS8 Stainless steel baying enclosures and accessories

Technical specificationMaterialEnclosure frame, roof, rear panel

and gland plates . . . . . . . Stainless steel1.4301 (AISI 304), 1.5mm

Door(s) . . . . . . . . . . . . . . Stainless steel1.4301 (AISI 304), 2.0mm

Mounting plate . . . Sheet steel, 3.0 mmSurface finishEnclosure frame andgland plates . . . . . . . . . . . . . Uncoated

Door, roof and rear panel. . . . . . Exterior brushed, grain size 400

Mounting plate . . . . . . . . . . . Zinc platedProtection category. . IP55 to IEC60529


ApprovalsULCSA TV

Russian Maritime Register of Shipping TV Mark Lloyds Register of Shipping Bureau VeritasVDEGermanischer Lloyd

Includes:

TS8 stainless steel baying enclosure

Mounting plateGland plates Rear panel Roof Locking rod with double-bit insert

NOTE: Due to the hardness of thematerial, we recommend using metalmulti-tooth screw SZ2486.300 for theinterior installation.

600 1800 500 499 1696 92.5 1 TS8457.600 1,302.97

600 2000 600 499 1896 104.4 1 2 TS8452.600 1,568.24

800 1800 400 699 1696 112.9 1 TS8454.600 1,545.04

800 1800 500 699 1696 116.3 1 TS8455.600 1,550.01

800 2000 600 699 1896 129.7 1 2 TS8450.600 1,794.97

1200 1800 400 1099 1696 170.4 2 TS8456.600 2,087.81

1200 1800 500 1099 1696 174.9 2 TS8453.600 2,250.48

1200 2000 600 1099 1896 194.7 2 2 TS8451.600 2,402.67

Dimensions (mm) Mounting Plate (mm) Weight No. of Support ListW H D W H (kg) Doors Strips fitted Order Code Price

Side panels, screw-fastened

1800 400 1 TS8609.840 46.80

1800 500 1 TS8609.850 55.55

2000 600 1 TS8609.060 70.13

Enclosure Enclosure Pack ListHeight (mm) Depth (mm) Qty Order Code Price

Divider panels

Material: Sheet steel, 1.5mm, zinc-plated

Material: Stainless steel


1800 500 9 TS8609.100 63.37

2000 600 10 TS8609.130 73.23

Enclosure Enclosure No. of ListHeight (mm) Depth (mm) cut-outs Order Code Price

Divider panels for module plates

Material: Sheet steel, 2mm, zinc-plated

600 1 set TS8701.600 91.52

800 1 set TS8701.800 104.25

1200 1 set TS8701.200 129.72


100mm plinth

Components front and rear

Set = Mounting accessories for mounting on theenclosure and 2 trim panels front/rear.

Material: Stainless steel, 1.4301 (AISI 304)

Set = Mounting accessories for mounting on theenclosure, 2 corner pieces with removable trim paneland 1 trim panel front/rear.


600 1 set TS8702.600 141.38

800 1 set TS8702.800 155.48

1200 1 set TS8702.200 183.80


200mm plinth

The TS range is also


see pages 174-176

1

2

3

4

Includesmounting

plate


21/32



TS8 Stainless steel bayingenclosure accessories (continued)

100mm plinth

400 1 set TS8701.040 50.69

500 1 set TS8701.050 54.63

600 1 set TS8701.060 58.58


Side trim panels

Set = 2 base/plinth trim panels, including parts for attaching to the base/plinth components


200mm plinth

400 1 set TS8702.040 58.08

500 1 set TS8702.050 65.31

600 1 set TS8702.060 72.41


400 4 SO2907.000 105.68

500 4 SO2908.000 127.01

600 4 SO2913.000 121.51


Base/plinth trim, modular

Set = 4 base/plinth trim panels


For cable routing in the stainless steel base/plinth,e.g. if levelling feet SO2889.000 or SO2890.000 are used.

Width 175mm.

Note: One base/plinth trim panel is needed per 200mm

base/plinth width.

600 2 PS4191.000 33.29

800 2 PS4192.000 34.61

1200 2 PS4196.000 42.52


Cable clamp rails

Material: Steel, zinc-plated

Material: Sheet steel, colour: RAL 7035

600 5 2 TS8700.600 43.70

800 8 2 TS8700.800 47.81

1200 6 4 TS8700.120 68.19

Enc Cut-outs Pack Order ListW(mm) per plate Qty Code Price

Cable entry plates

Material: TS8700.600/800 = Steel, zinc-platedTS8700.120 = Stainless steel, 1.4301 (AISI 304)

600 90 455 210 TS4116.000 24.05

800 90 655 210 TS4118.000 27.87

To fit door Clearance opening ListW (mm) D (mm) W (mm) H (mm) Order Code Price

Wiring plan pockets

6-12 25 SZ2350.000 39.59

12-16 25 SZ2351.000 41.31

14-18 25 SZ2352.000 42.64

18-22 25 SZ2353.000 44.08

22-26 25 SZ2354.000 46.66

26-30 25 SZ2355.000 50.49

30-34 25 SZ2356.000 54.74

34-38 25 SZ2357.000 57.15

38-42 25 SZ2358.000 59.44

42-46 25 SZ2359.000 62.50

46-50 25 SZ2360.000 64.04


Cable clamps

Side panelsScrew-fastened, stainless steel with

automatic potential equalisation(Includes assembly parts)

Divider panelsFor shielding individual enclosure cells.The divider panel may also be fitted at

the rear. (Includes assembly parts)

Divider panels formodule plates

With cut-outs for the installation ofmodule plates for connectors or for

cable entry. (Includes assembly parts andmulti-tooth screws)





Side trim panels

100mm or 200mm high


Cable clamp railsFor strain relief with cable entry.

Depth variable mounting on a 25mmpitch pattern on the horizontal enclosuresection or in side base/plinth trim panels

with assembly bolts.(Includes assembly parts)

Cable clampsFor cable clamp rails

For fastening the cables to thecable clamp rails.

(Includes plastic insert)

Cable entry platesFor fastening to tubular door frames atany height. (Includes assembly parts)

Base/plinth trim, modularFor cable routing in the stainless steel

base/plinth. Note: One base/plinth trimpanel is needed per 200mm base/plinth

width (Includes 4 base/plinth trim panels)

1

5

6

7 8

9

10

3

4

5

7

8

6

9

Wiring plan pocketsFor fastening to tubular door frames atany height. (Includes assembly screws)

10

2

Divider panel

Base/plinth trim

Side trim panels Component front and rear

Wiring plan pocketCable clamp rails


22/32



100mm plinth

400 1 set TS8701.040 50.69

500 1 set TS8701.050 54.63

600 1 set TS8701.060 58.58


Side trim panels (RAL 7022)

Set = 2 base/plinth trim panels, including parts for attaching to the base/plinth components


200mm plinth

400 1 set TS8702.040 58.08

500 1 set TS8702.050 65.31

600 1 set TS8702.060 72.41


600 1 set TS8701.600 91.52

800 1 set TS8701.800 104.25

1000 1 set TS8701.000 100.07

1200 1 set TS8701.200 129.72

Enclosure Pack List

W (mm) Qty Order Code Price

100mm plinth

Components front and rear (RAL 7022)

Set = Mounting accessories for mounting on theenclosure and 2 trim panels front/rear.


Set = Mounting accessories for mounting on theenclosure, 2 corner pieces with removable trim paneland 1 trim panel front/rear.


600 1 set TS8702.600 141.38

800 1 set TS8702.800 155.48

1000 1 set TS8702.000 180.35

1200 1 set TS8702.200 183.80

Enclosure Pack List

W (mm) Qty Order Code Price

200mm plinth

SE8 Stainless steel system enclosures and accessories

Technical specificationMaterialEnclosure and rear panel . Stainless steel

1.4301 (AISI 304), 1.5mmDoor(s) . . . . . . . . . . . . . . Stainless steel

1.4301 (AISI 304), 2.0mm

Mounting plate . . . . Sheet steel, 3.0mm

Surface finishEnclosure, rear panel, gland plate

and door(s) . . . . . . Brushed, grain 240Mounting plate . . . . . . . . . . . Zinc platedProtection category. . IP55 to IEC60529


Includes: SE8 stainless steel system enclosureDoor(s) Rear panel, detachable

130 hingesMounting plateGland plates, divided Locking rod with double-bit insert

NOTE: Due to the hardness of thematerial, we recommend using metalmulti-tooth screw SZ2486.300 for theinterior installation.

600 1600 400 499 1496 1 SE5850.500 1,457.46

600 1800 500 499 1696 1 SE5851.500 1,525.57

800 1800 500 699 1696 1 SE5852.500 1,749.57

800 2000 600 699 1896 1 SE5853.500 2,083.39

1000 1800 400 899 1696 1 SE5854.500 1,969.03

1200 2000 500 1099 1896 2 SE5855.500 2,709.01

Dimensions (mm) Mounting Plate (mm) No. of ListW H D W H Doors Order Code Price


Components front and rear

Side trim panels

400 4 TS8612.040 34.76

500 4 TS8612.050 37.93

600 4 TS8612.060 44.63

Enclosure Pack List

D (mm) Quantity Order Code Price

Enclosure Pack List

D (mm) Qty Order Code Price400 4 TS8612.140 34.27

500 4 TS8612.150 37.48

600 4 TS8612.160 44.18

Enclosure Pack List

D (mm) Quantity Order Code Price

Enclosure Pack List

D (mm) Qty Order Code Price

Punched section with mounting flange


Material: Sheet steel, zinc-plated Material: Sheet steel, zinc-plated

The SE range is also


see pages 172-173

1

2

3

Includesmounting

plate


23/32



SE8 Stainless steel bayingenclosure accessories(continued)

4 PS4568.000 16.32

Pack List

Qty Order Code Price

Roof eyebolts

600 2 PS4191.000 33.29

800 2 PS4192.000 34.61

1000 2 PS4336.000 42.62

1200 2 PS4196.000 42.52


Cable clamp rails

Material: Steel, zinc-plated

Thread: M12

Please contact sales on 01254 685900for alternative locking systems

6-12 25 SZ2350.000 39.59

12-16 25 SZ2351.000 41.31

14-18 25 SZ2352.000 42.64

18-22 25 SZ2353.000 44.08

22-26 25 SZ2354.000 46.66

26-30 25 SZ2355.000 50.49

30-34 25 SZ2356.000 54.74

34-38 25 SZ2357.000 57.15

38-42 25 SZ2358.000 59.44

42-46 25 SZ2359.000 62.5046-50 25 SZ2360.000 64.04


Cable clamps

Wall mounting brackets Stainless steel

Bracket AFor the attachment of KL, EB, BG and EL enclosuresas well as DK wall-mounted distributors.

Stainless steel, 1.4301 (AISI 304) 8 4 KL1594.000 18.96

Wall Pack ListMaterial distance (mm) Qty Order Code Price

Stainless steel, 1.4301 (AISI 304) 10 4 SZ2433.000 23.68

Stainless steel, 1.4401 (AISI 316L) 10 4 SZ2433.500 24.22

Wall Pack ListMaterial distance (mm) Qty Order Code Price

Bracket B

For the attachment of KL, EB, BG, AE, CM and EL enclosures, TP consolesas well as DK wall mounted distributors and small fibre-optic distributors.

NOTE: For hygiene reasons, and in viewof the protection category, the stainlesssteel enclosures do not have any drilledholes for the wall mounting brackets.

Bracket A Bracket B

Punched section withmounting flange

Roof eyeboltsCable clamps





Side trim panels100mm or 200mm high


1

4 5

6

2

Punched sectionwith 17 x 73mm mounting flange


universal skeleton structures or partialassembly. Simply locate into theTS punchings and secure.(Includes assembly screws)

3

Cable clamp railsFor strain relief with cable entry. Depthvariable mounting on a 25mm pitchpattern on the horizontal enclosure

section or in side base/plinth trim panels.(Includes assembly parts)

4

Cable clamps(For cable clamp rails)

Used for fastening the cables to the

cable clamp rails. Sheet steel withzinc-plated surface finish.(Includes plastic insert)

5

Roof eyeboltsUsed for crane transportation of

enclosures. Thread M12.

6


24/32



Terminal boxes Hygienic design


MaterialEnclosure and cover . . . Stainless steel

1.4301 (AISI 304) 1.5mmQuick-release fasteners. Stainless steelSeal. . . . . . . . . Silicone, compliant with

FDA guideline 21 CFR 177.2600

Surface finish

Enclosure and cover. . . . . . . Brushed,grain 400, RA


25/32



Why use hygiene compatible cable glands?Critical points with conventional solutions

1 Cable entry in frontof seal

2 No minimum radiion the hexagon

3 External thread

4 Gap caused by O-ringon the enclosure surface

Hygiene compatible design features

1 Seal directly at thecable entry

2 Compliance with minimumradii on the hexagon

3 No external thread

4 Flush termination betweenthe cap nut and the enclosure

12

3

4

12

34

50 1 HD4000.100 16.61

Wall Distance Pack List(mm) Qty Order Code Price

Wall spacer bracket HD

150 150 KL1560.700 3.75

200 200 KL1562.700 5.01

300 200 KL1563.700 6.18

400 200 KL1564.700 7.75

400 300 KL1568.700 10.60

EnclosureW H List


Mounting plates (terminal box)

Material: Sheet steel, 2mm

150 137 TS 35/7.5 10 SZ2314.000 22.55

200 187 TS 35/7.5 10 SZ2315.000 25.22

300 287 TS 35/7.5 10 SZ2316.000 32.99400 387 TS 35/7.5 10 SZ2317.000 32.74


Support rails (DIN rail) Length sized to enclosure width

M12 x 1.5 3-6.5 5 Standard HD2410.000 69.42M16 x 1.5 4.5-10 5 Standard HD2410.010 73.33

M16 x 1.5 5-10 5 EMC HD2410.110 88.53

M20 x 1.5 6-12 5 Standard HD2410.020 82.99

M20 x 1.5 6-12 5 EMC HD2410.120 100.52

M25 x 1.5 11-17 5 Standard HD2410.030 101.60

M25 x 1.5 12-17 5 EMC HD2410.130 123.02

Cable Pack ListSize Diameter (mm) Qty Version Order Code Price

Cable gland HD

1 HD2304.010 32.50

Pack ListQty Order Code Price

Cam lock HD1 set HD2410.290 16.93

Pack ListQty Order Code Price

Assembly tool for HD cable gland

510 4 CM5001.050 22.79

710 4 CM5001.051 27.53

910 4 CM5001.052 32.29

1110 4 CM5001.053 33.67


Rail Pack ListL (mm) Qty Order Code Price


Material: Sheet steel, zinc-plated

Set includes: Adaptor for sizes from M12-M25

Levelling feet HD

M12 120-175 Without 4 HD4000.200 148.26

M12 120-175 With 4 HD4000.210 163.61

Levelling Base Pack ListThread Range (mm) Mount Qty Order Code Price

M12 x 1.5 10 HD2410.200 13.17

M16 x 1.5 10 HD2410.210 13.57

M20 x 1.5 10 HD2410.220 15.34

M25 x 1.5 10 HD2410.230 18.62

Pack ListSize Qty Order Code Price

Stainless steel lock nut

Enclosure key - HD 1 HD2549.600 2.43

Bit HD lock for universal key 2549.500 1 HD2549.510 2.18


Keys/locks HD

Hygienic design accessories

Levelling feet HD

Wall spacer brackets Enclosure key


26/32



SK3237.100, 110, 124 5 SK3321.700 8.37

SK3238.100, 110, 124 5 SK3322.700 9.60

SK3239.100,110, 124 5 SK3171.100 13.92

SK3240.100,110, 124/SK3241.100,110, 124 5 SK3172.100 15.15

SK3243.100, 110/SK3244.100, 110/ SK3245.500 5 SK3173.100 19.17

Pack ListFor Fan and Filter Units . . . Quantity Order Code Price

Filter mats

116.5 x 116.5 SK3237.200 17.62

148.5 x 148.5 SK3238.200 21.67

204 x 204 SK3239.200 24.37

255 x 255 SK3240.200 27.99

323 x 323 SK3243.200 29.56

Dimensions List(mm) Order Code Price

Outlet filters

116.5 x 116.5 SK3237.060 47.59

148.5 x 148.5 SK3238.060 62.79

204 x 204 SK3239.060 82.63

255 x 255 SK3240.060 87.12

323 x 323 SK3243.060 96.74

Dimensions List(mm) Order Code Price

Outlet filters EMC

20-25m3/h 230 50/60 116.5 x 116.5 SK3237.100 47.34

20-25m3/h 115 50/60 116.5 x 116.5 SK3237.110 50.80

20m3/h 24V d.c. - 116.5 x 116.5 SK3237.124 55.17

55-66m3/h 230 50/60 148.5 x 148.5 SK3238.100 77.23

55-66m3/h 115 50/60 148.5 x 148.5 SK3238.110 82.54

55m3/h 24V d.c. - 148.5 x 148.5 SK3238.124 94.08

105-120m3/h 230 50/60 204 x 204 SK3239.100 90.88

105-120m3/h 115 50/60 204 x 204 SK3239.110 97.11

105m3/h 24V d.c. - 204 x 204 SK3239.124 119.68

160-180m3/h 230 50/60 255 x 255 SK3240.100 90.67

160-180m3

/h 115 50/60 255 x 255 SK3240.110 93.07180m3/h 24V d.c. - 255 x 255 SK3240.124 153.54

230-250m3/h 230 50/60 255 x 255 SK3241.100 99.11

230-250m3/h 115 50/60 255 x 255 SK3241.110 108.91

230m3/h 24V d.c. - 255 x 255 SK3241.124 188.25

550-600m3/h 230 50/60 323 x 323 SK3243.100 126.68

550-600m3/h 115 50/60 323 x 323 SK3243.110 139.02

700-770m3/h 230 50/60 323 x 323 SK3244.100 146.97

700-770m3/h 115 50/60 323 x 323 SK3244.110 154.50

700-770m3/h 400-460 3-phase 50/60 323 x 323 SK3244.140 207.24

900m3/h 230 50/60 323 x 323 SK3245.500 291.58

Air Throughput Rated Operating Voltage Dimensions ListUnimpeded Air Flow V a.c. Hz (mm) Order Code Price

Fan and filter units

20-25m3/h 230 50/60 116.5 x 116.5 SK3237.600 104.16

55-66m3/h 230 50/60 148.5 x 148.5 SK3238.600 151.67

105-120m3/h 230 50/60 204 x 204 SK3239.600 200.81

160-180m3/h 230 50/60 255 x 255 SK3240.600 205.27

230-250m3/h 230 50/60 255 x 255 SK3241.600 225.69

550-600m3/h 230 50/60 323 x 323 SK3243.600 236.66

700-770m3/h 230 50/60 323 x 323 SK3244.600 304.86

900m3/h 230 50/60 323 x 323 SK3245.600 464.45

Air Throughput Rated Operating Voltage Dimensions ListUnimpeded Air Flow V a.c. Hz (mm) Order Code Price

Fan and filter units EMC

TopTherm fan and filter units

Technical specificationColour . . . . . . . . . . . . . . . . . . RAL 7035

Includes: TopTherm fan and filter unit ready

for installation Filter mat

NOTE: For energy-efficient operation

of the fan-and-filter units, we recommendusing the enclosure internal thermostat, thedigital thermostat with display or the speedcontrol (not compatible with 24V d.c. or900m3/h fan and filter units) on page 187

Outlet filter

Fan and filter units


27/32



160m3/h 230 50/60 SK3108.100 89.82

160m3/h 24V d.c. - SK3108.024 120.88

Air Throughput Rated Operating Voltage ListUnimpeded Air Flow V a.c. Hz Order Code Price

Enclosure internal fan

Digital thermostat with display SK3114.200 72.89Enclosure internal thermostat SK3110.000 22.24

Hygrostat SK3118.000 72.18

Speed control (see note on page 186) SK3120.200 145.22

ListDescription Order Code Price

Accessories

SK3237.xxx 5 SK3237.066 12.01

SK3238.xxx 5 SK3238.066 17.59

SK3239.xxx 5 SK3239.066 30.28

SK3240.xxx/SK3241.xxx 5 SK3240.066 45.11

SK3243.xxx/SK3244.xxx/SK3245.xxx 5 SK3243.066 69.76

Pack ListFor Fan and Filter Units EMC . . . Qty Order Code Price

Filter mats EMC

SK3238.xxx 5 SK3238.055 7.35SK3239.xxx 5 SK3181.100 13.92

SK3240.xxx/SK3241.xxx 5 SK3182.100 15.15


Pack ListFor Fan and Filter Units . . . Qty Order Code Price

Fine filter mats

SK3237.xxx 1 SK3237.080 54.26

SK3238.xxx 1 SK3238.080 60.05

SK3239.xxx 1 SK3239.080 72.46

SK3240.xxx/SK3241.xxx 1 SK3240.080 99.21SK3243.xxx/SK3244.xxx 1 SK3243.080 120.84

SK3245.xxx 1 SK3245.080 199.19


Hose-proof hoods

SK3237.xxx 1 SK3237.020 11.38

SK3238.xxx 1 SK3238.020 13.13

SK3239.xxx 1 SK3239.020 14.11

SK3240.xxx/SK3241.xxx 1 SK3240.020 16.24



Blanking covers

TopTherm fan and filter unit accessories

Fine filter mats

Hose-proof hoods

Auto range power pack

Blanking covers


28/32



250W 250W with fan 4A 142 x 170 x 101mm SK3105.380 135.09



Continuous Thermal Pre Fuse Dimensions ListDescription Output at Tu = 10C gG (w x h x d) Order Code Price

With fan, continuous thermal output, 240V a.c.

10W 8-10W 2A 45 x 120 x 46mm SK3105.310 31.94

20W 18-20W 2A 45 x 120 x 46mm SK3105.320 33.97

30W 23-30W 4A 64 x 155 x 56mm SK3105.330 44.69

50W 49-50W 4A 64 x 155 x 56mm SK3105.340 54.10

75W 63-75W 4A 64 x 230 x 56mm SK3105.350 63.91

100W 86-100W 4A 90 x 165 x 75mm SK3105.360 77.98

150W 130-150W 4A 90 x 180 x 75mm SK3105.370 87.63

Continuous Thermal Pre Fuse Dimensions ListDescription Output at Tu = 10C T (w x h x d) Order Code Price

Without fan, continuous thermal output, 240V a.c.

Enclosure heaters

Includes:

Enclosure heater PTC heater

Quick connection terminalAssembly parts

Notes:

For precise temperature controlinside the enclosure, we recommendthe enclosure int

Documents

Enclosur100Base-TX to 100Base-FX Single Mode SC Fiber Converter (30KM, 18.6 Miles)e Catalogue Products