ENAMO GRIP - Amazon Simple Storage Service · Enamo Grip is a super tough, two component self-leveling polyurethane enamel that can be tinted to any color to achieve high gloss results

ENAMO GRIP 21st Century Solutions For Age Old Problems

The anti-graffiti system is based on Enamo Grip. Enamo Grip is a two-part polyurethane enamel coating that performs as a hard, durable topcoat on steel, concrete, masonry, wood, and most other surfaces. Made of a self-leveling formula, it provides exceptional adhesion, flexibility and abrasion/impact resistance as well as excellent color retention and chalk resistance when used on exterior surfaces. Enamo Grip is resistant to water and humidity, stains, chemicals, and other harsh solvents. Benefits:

Graffiti protection

High-gloss, semi-gloss, satin finish

Extremely tough

Self-leveling (no brush marks)

Provides a permanent, protective membrane that stops water penetration

Above buses in Rome, Italy, covered with graffiti are cleaned with SPI Graffiti Cleaner, powerwashed and placed back into service.

SPI-DOT Group P.O. Box 70237

Charleston, SC 29415 Tel: (843) 554-6496

Fax: (843) 554-6498

John Grey (843) 813-6402

Another quality product from SUPERIOR PRODUCTS INTERNATIONAL II, INC.

Product Overview

ENAMO GRIP 21st Century Solutions for 20th Century Challenges

Apply Enamo Grip with brush, roller, or spray.

Use as a topcoat with Rust Grip to provide any desired color finish coat.

Enamo Grip provides outstanding resistance to water, humidity stains, chemicals, solvents, and is tremendously scuff, mar and impact resistant.

Enamo Grip is a super tough, two component self-leveling polyurethane enamel that can be tinted to any color to achieve high gloss results.

Enamo grip is applied in clear high gloss over painted surfaces to provide graffiti protection. Graffiti can be removed using a graffiti remover without harm to the coating surface. After removal, the surface appears new and fresh without shadows or residues. No more repainting. The surface must be coated with the Clear Enamo Grip first before graffiti is applied.

Enamo Grip is currently being used to protect trains, buses and trams in Rome, Italy for ease of graffiti removal without repainting and has been saving thousands of dollars annually on prevention. See pictures below.

BENEFITS:

Provides permanent, protective membrane to stop water penetration

Protects steel, aluminum, concrete, masonry, and other substrates

Prevents surface deterioration, contamination, and mold & mildew

Extremely tough with a 15 year lifespan under normal conditions

Self-leveling give smooth, glossy surface appearance

Applied as a clear (required for graffiti) or tinted coat

USES: Anti-graffiti protection for surfaces. Applied and cured Enamo Grip can resist graffiti

Topcoat over Rust Grip when specific color is required, to give a long life to the surface

Topcoat over Super Therm to provide additional protection and durability for a substrate

Protects against UV, wear, weathering, and moisture protection

Seals against moisture and protects against weathering

SUPERIOR PRODUCTS


Technical Data Sheet (09/10/07)

DESCRIPTION

Enamo Grip is a two-part polyurethane enamel that forms a uniquely

hard and durable coating film, which demonstrates unsurpassed semi-

gloss retention, color retention and chalk resistance when used in

exterior applications. It is resistant to water and humidity, stains,

acids, solvents, and chemicals, as well as having tremendous scuff,

mar and impact resistance.

Although available in colors, Enamo Grip (Clear) provides exceptional

graffiti resistance and protection. Krylon spray paints, magic markers,

etc. can be removed completely with SPI’s Graffiti Cleaner. Enamo

Grip can withstand repeated incidents of graffiti removal as it is

resistant to solvents. It can provide tremendous cost savings by

eliminating blasting and re-painting of graffiti affected surfaces on

trains, buses, trams, and buildings.

The formula of resins in Enamo Grip will spread and self-level into an

even, and smooth finish. No brush marks when applied by brush.

TYPICAL USES

For architectural and maintenance solutions that require the utmost

in exterior durability;

As a topcoat for Rust Grip®

and Moist Metal Grip;

As a coating system for graffiti protection;

As a floor covering where a tough, long-lasting finish is required.

The coating has non-skid characteristics built into the formulation;

Anywhere that a UV-resistant topcoat is required.

APPLICATION METHODS

Enamo Grip can be applied to metal, concrete, masonry, wood and

other porous surfaces. The application can be by spray, brush or roller.

For specific instructions on surface preparation, mixing and

application, please refer to the SPI’s application instructions for

Enamo Grip.

MINIMUM SPREAD RATE (mil thickness)

Metal: Apply at 250 sq ft/gallon

6.5 mils wet / 3 mils dry

Concrete, Masonry: Apply two coats @ 200 sq ft/gal each coat

8 mils wet / 3.67 dry mils dry

TESTS AND CERTIFICATIONS

1) USDA Approved

2) Marine Approval for Salt Water/Maritime Uses:

US Coast Guard

ABS (American Bureau of Shipping)

IMO (International Marine Organization)

3) Flame Spread (ASTM E84) Class A Fire Rating

4) Abrasion (ASTM D4060)

FEATURES

Solids: By volume: 45.9% By weight: 60.0%

Dry Time: One hour to touch, overcoat window is three hours, or

longer

Lead- and Chromate-free

Cures by moisture in the air and heat reactivity

Weight: 9.8 lbs per gallon

Vehicle Type: Aliphatic Polyurethane

Shelf Life: Up to three years (unopened) under appropriate storage

conditions (See MSDS)

VOC: Clear finish – 537 grams per liter; Black – 523 grams per liter

Heat Resistance: 2.3% mass lost @ 249.8 C degrees (482F.) Limit is

20% mass lost @ 350C. degrees (662F.).

Impact Resistance: (Front) 160 psi / (Back) 100 psi

Mix Ratio: 1 part curing agent to 3 parts base

Pot Life: Four hours at 70 F. degrees / One hour at 90 F. degrees

If temperature exceeds 90 F. degrees, mix base and curing agent and

apply immediately.

Colors available with established minimum quantities

SAFETY PRECAUTIONS

Do not use this product without first taking all Do not use this product

without first taking all appropriate safety measures to prevent property

damage and injuries. These measures may include, without limitation:

proper ventilation, use of proper lamps, wearing of protective clothing

and masks, tenting, and proper separation of application areas. This

coating is flammable. Keep away from flame, fire, or other sources of

ignition. For more specific safety procedures, please refer to the Enamo

Grip Materials Safety Data Sheet. KEEP OUT OF REACH OF

CHILDREN.

LIMITATION OF LIABILITY: The information contained in this data sheet is

based upon tests that we believe to be accurate and is intended for guidance only.

All recommendations or suggestions relating to the use of the products made by

SPI, whether in technical documentation, or in response to a specific enquiry, or

otherwise, are based on data which to the best of our knowledge is reliable. The

products and information are designed for users having the requisite knowledge

and industrial skills, and the end-user has the responsibility to determine the

suitability of the product for its intended use.

SPI has no control over either the quality of condition of the substrate, or the many

factors affecting the use and application of the product. Therefore, SPI does not

accept any liability arising from loss, injury, or damage resulting from such use or

the contents of this data sheet (unless there are written agreements stating

otherwise).

The information contained in this data sheet is subject to modification as a

result of practical experience and continuous product development. This data

sheet replaces and

annuls all previous issues and the user has the responsibility to ensure that

this sheet is current prior to using the product.

SUPERIOR PRODUCTS


Application Instructions (08/04/06)

Enamo Grip is a two-part polyurethane enamel that forms a

uniquely hard and durable coating film. This self-leveling

coating is resistant to water, acids, solvent and impact.

Enamo Grip is a one-coat system. Enamo Grip can be

applied to metal, concrete, masonry and wood.

SURFACE PREPARATION

As a topcoat:

1) Surface must be clean and free of oil, tar, grease and film.

2) Surface must be completely dry before applying.

3) Enamo Grip must be applied during the prescribed

overcoat window of the coating to which it will be

applied.

4) If applied over an existing coating and this coating is

glossed, it must be sanded and roughed before

application, no gloss.

Can be applied as a one-coat system for graffiti protection

(Enamo Grip in clear finish only).

MIXING

1) Open pail, mix base with curing agent 3:1 ratio.

2) Mix by hand for two minutes.

3) If below 70 F. degrees, allow to stand for 30 minutes.

4) Begin application; however, do not apply in direct

sunlight. During the summer months, apply the coating

in the morning or after 4:00 p.m.

POT LIFE

Four hours at 70 F. degrees; two hours at 90 F. degrees, once

base and curing agent have been mixed.

TEMPERATURE

1) Apply between 40 F. and 120 F. degrees.

2) Store between 40 F. and 120 F. degrees according to

hazmat standards indicated on MSDS.

APPLICATION

Enamo Grip can be applied by brush, roller or spray; however,

the preferred method is by brush or roller:

1) If application is by brush, use a soft bristle brush.

2) If application is by roller, use a 1/4 inch nap roller. Then

use a brush any trapped air bubbles, if any.

3) If application is by spray, use a standard airless sprayer

(2,800 psi or less) with a .024 tip.

NOTE: The number of coats and the thickness of each will be

in accordance with the job specifications.

MINIMUM SPREAD RATES (mil thickness)

Porous Surfaces – Apply in 2 coats at 200 sq ft per gallon at 8

mils wet/3.67 mils dry.

Non-Porous Surfaces – Apply at 250 sq ft per gallon at 6.5

mils wet/3 mils dry.

CURE TIME

1) One hour to touch at 70 F. degrees.

2) Overcoating window is three hours at 70 F. degrees or

longer.

3) Fully cures in ten days.

4) If temperature is over 90 F. degrees, cure time and pot

life is shortened to one hour.

CLEAN-UP EQUIPMENT

1) During breaks, spray system should be flushed with

solvent.

2) After completion, spray systems should be flushed and

cleaned with MEK or other comparable solvents.

3) After completion, brushes and rollers should be cleaned

with MEK or other comparable solvents, stored and

reused.

(E/S/10/02)

NAV = Not Available NAP = Not Applicable


MATERIAL SAFETY DATA SHEET

SECTION I – IDENTIFICATION OF PRODUCT AND COMPANY PRODUCT IDENTIFIER: Enamo Grip

PRODUCT USE: Applied Over Surfaces to Provide a Tough, Protective Topcoat

MANUFACTURER: Superior Product International II, Inc.

ADDRESS: 10835 W. 78th Street Shawnee, KS 66214 USA

EMERGENCY TELEPHONE #: 1-800-424-9300 TELEPHONE #: 1-202-483-7616

SECTION II - HAZARDOUS INGREDIENTS HAZARDOUS INGREDIENTS % CAS/PIN LD50 (Species/Route) LC50 (Species)

n-butyl acetate 15.00 123-86-4 NAV NAV

methyl isobutyl 8.87 108-10-1 NAV NAV

ketonetoluol 9.58 108-88-3 NAV NAV

ethyl 13-ethoxypropionate 5.57 763-69-9 NAV NAV

ethyl acetate 12.97 141-78-6 NAV NAV

homopolymer of HDI 13.00 28182-81-2 NAV NAV

SECTION III – HAZARD IDENTIFICATION The product is a flammable, solvent-based epoxy and should be treated according to all known safety precautions. Refer to Section

VII for Storage and Handling recommendations, Section VIII for Personal Protection, Section XIV for transport.

SECTION IV – FIRST AID MEASURES EYES: Flush with water for at least 15-20 minutes, occasionally lifting eyelids. See physician.

INGESTION: Do not induce vomiting. Drink 1-2 glasses milk or water. Seek medical attention according to amount of product

ingested.

SKIN: Remove contaminated clothing. Wash affected areas and clothing with mild soap and water.

INHALATION: Remove to fresh air. Give oxygen, if required. Seek medical help.

SECTION V – FIREFIGHTING MEASURES CONDITIONS OF FLAMMABILITY: Spraying or other activities to create finely divided droplets around open flame/sparks.

HAZARDOUS COMBUSTION PRODUCTS: Carbon monoxide, aldehydes, fumes

FLAMMABLE LIMITS: (Lower) 1.4 % (Upper) 7.6 % FLASHPOINT & METHOD: 35 F. TCC

MEANS OF EXTINCTION: Foam, water spray (fog), dry chemical, carbon dioxide

SPECIAL PROCEDURE: Firefighters should wear full-body protection & SCBA

MINIMUM IGNITION ENERGY: NAV AUTOIGNITION TEMP: 350 C. degrees

SENSITIVITY TO MECHANICAL IMPACT: NAV SENSITIVITY TO STATIC DISCHARGE: NAV

SECTION VI – ACCIDENTAL RELEASE MEASURES Ventilate the area, control spill by covering with sawdust or similar agent. Pour decontamination solution over spill (non-ionic

surfactant Union Carbide’s Tergitol TMN-10 (20%) + water (80%).

SECTION VII – HANDLING AND STORAGE STORAGE REQUIREMENTS: Maintain temperature between 32-122 F. degrees; average shelf life is 12 months @ 77 F. degrees

HANDLING PROCEDURES/EQUIPMENT: Ground all containers; use non-sparking tools.

SECTION VIII – EXPOSURE CONTROLS AND PERSONAL PROTECTION PERSONAL PROTECTION EQUIPMENT: Half-face respirator with organic vapor filter, safety glasses with shields, PVA or

nitrile chemical-resistant gloves, skin protection.

ENGINEERING CONTROLS: Mechanical exhaust fan.

SECTION VIX – PHYSICAL AND CHEMICAL PROPERTIES PHYSICAL STATE: Liquid BOILING POINT: NAV VAPOUR DENSITY (Air = 1): 1 +/-

SOLUBILITY IN WATER: Insoluble SPECIFIC GRAVITY: 1.0 pH: NAP

ODOR THRESHOLD: NAV VAPOUR PRESSURE: NAV COEFF. WATER/OIL: NAV

FREEZING POINT: NAP VOLATILES: NAV EVAPORATION RATE: 1%

APPEARANCE AND ODOR: Various colors, liquid, ester solvent odor


MSDS (Continued) (E/S/10/02)

NAV = Not Available NAP = Not Applicable

SECTION X – STABILITY AND REACTIVITY DATA CONDITIONS OF REACTIVITY: By high heat or fire CORROSIVE BEHAVIOR: No

CHEMICAL INCOMPATIBILITY: Amines, strong bases and alcohols

CONDITIONS OF INSTABLITY: Stable under normal conditions

HAZARDOUS DECOMPOSITON PRODUCTS: Carbon dioxide, carbon monoxide, oxides of nitrogen

SECTION XI - TOXICOLOGICAL PROPERTIES ROUTES OF ENTRY: Skin Contact: X Eye Contact: X Inhalation: X

TERATOGENICITY: NAV REPRODUCTIVE TOXICITY: NAV EXPOSURE LIMITS: NAV

IRRITANCY: Burning sensation MUTAGENICITY: NAV CARCINOGENICITY: NAV

SENSITIZATION: Can cause future reaction to lesser amounts SYNERGISTIC PRODUCTS: NAV

EFFECTS OF ACUTE EXPOSURE: Burning sensation on mucous membranes & respiratory tract. Flu-like symptoms

(fever and chills).

EFFECTS OF CHRONIC EXPOSURE: Chemical asthma - chest tightness, wheezing, coughing, shortness of breath. Can

cause lung damage.

SECTION XII – ENVIRONMENTAL INFORMATION AIR: 3.75 lbs./gallon; 537 grams per liter V.O.C. (clear); 523-black

WATER: Insoluble in water.

SOIL: Lead-and chromate free/not hazardous under RCRA 40CFR

SECTION XIII – WASTE DISPOSAL Incineration preferred. Dispose of in accordance with federal, state, and local government regulations.

SECTION XIV – TRANSPORT INFORMATION Classified a hazardous material (Class 3//U1263//P.G. II), and should be marked and handled according to specific regulations. Tariff

code 3208.90.0000.

SECTION XV – REGULATORY INFORMATION Materials listed under Superfund Amendments and Reauthorization Act of 1988 (SARA) 302, 304, 311, 312, 313: Methyl Isobutyl

Ketone (CAS 108-10-1), Toluol (CAS 108883)

SECTION XVI – OTHER INFORMATION NAV

PREPARATION INFORMATION

PREPARED BY: J. Pritchett, Superior Product International II, Inc. DATE OF PREPARATION: 09/10/07

Simmons Army Airfield - Hangars Ft. Bragg, NC

May 2007


Pictured Above: Before picture of hangar coated with LBP Surface Prep: Powerwash at 3,500 psi Primer System: Coated with 8 mils wet/4 mils dry Rust Grip® Pictured Right: Enamo Grip tinted to a Desert Tan color.

Simmons Army Airfield, Ft. Bragg

Deluge Tanks Fayetteville, NC

May 2007


Two deluge tanks coated with lead based paint are currently being coated at Ft. Bragg. At right, one of the tanks is being power washed, the only surface prep required.

Tanks are coated with Rust Grip as the primer and will be topcoated with Enamo Grip tinted to Desert Tan.

Enamo Grip is a super tough, two component self-leveling polyurethane enamel that can be tinted to any color to achieve high gloss results.

SUPERIOR PRODUCTS

GRAFFITI CLEANER 21st Century Solutions For 20th Century Challenges

Technical Data Sheet & Application Instructions (08/04/06)

DESCRIPTION Graffiti Cleaner is a water reducible, aggressive cleaner used

to dissolve and release most spray paints, markers and

enamels without shadow. Wipe off graffiti with rags, then

powerwash or hose down, for a bright finish.

SPECIFICATIONS

Physical Appearance: Water-thin liquid

Color: Clear

Freezing Point: -20C. degrees

Boiling Point: 202-204C. degrees

Specific Gravity: 1.05-1.07 (20C. degrees)

Flash Point: 197 F. degrees

Odor: Sweet

VOC: 0 (Extremely low vapor pressure)

USE

Spray GRAFFITI CLEANER over graffiti. Wait 15 minutes

and power wash off; in some cases, hose off. GRAFFITI

CLEANER is completely biodegradable and causes no harm

to the environment.

GRAFFITI CLEANER use to remove graffiti from ENAMO

GRIP works very effectively. Prior warning must be given if

applying GRAFFITI CLEANER over graffiti on top of other

paints. The cleaner may cut through other paints and cause

the base paint to come off.

NOTE: Use rubber gloves and eyewear when using product

to protect from mist and prolonged contact with skin. If

prolonged contact with skin occurs, skin will wrinkle and dry.

Use hand lotion over a 3-5 day period while the top layer of

skin peels off. After use, wash with soap and water on

exposed areas.

WARNING

Do not take internally. Avoid contact with eyes. If solution

does come in contact with eyes, flush immediately with water

and contact a physician for medical attention. Avoid

prolonged contact with skin or breathing of spray mist. For

quickest removal from skin, wash with water before product

dries. KEEP OUT OF REACH OF CHILDREN.

SURFACE PREPARATION 1) Spray generously over existing graffiti paints and wipe

off the old paint.

2) Apply generously and wipe until quickly removed.

MIXING 1) No need for mixing; comes ready to use.

2) Can package into spray bottles for easy spraying by hand.

POT LIFE Can evaporate if open container is left in the sun.

APPLICATION Graffiti Cleaner can be applied by brush, roller or spray;

however, the preferred method is by spray:

1) If application is by brush, use a soft bristle brush.

2) If application is by roller, use a ½” nap roller.

3) If application is by spray, use a standard airless sprayer

(2,800 psi or less) with a .017 tip.

4) For small jobs, package into handheld plastic spray

bottles.

NOTE: The number of coats is dictated by the thickness of

the layers of graffiti paint.

MINIMUM SPREAD Apply until cleaned off.

CURE TIME No cure time.

TEMPERATURE 1) Apply between 40 F. and 120 F. degrees.

2) Store between 40 F. and 120 F. degrees according to

hazmat standards indicated on MSDS.

CLEAN UP OF EQUIPMENT 1) No clean up necessary.

2) Handheld plastic bottles can be melted after one day of

use.

ENAMO GRIP CLEAR & SPI GRAFFITI CLEANER

21st Century Solutions for 20th Century Challenges Trains in Rome, Italy

Enamo Grip is a two-part polyurethane enamel coating that performs as a hard, durable topcoat on steel, concrete, masonry, wood, and most other surfaces. Made of a self-leveling formula, it provides exceptional adhesion, flexibility and abrasion/impact resistance as well as excellent color retention and chalk resistance when used on exterior surfaces. Enamo Grip is resistant to water and humidity, stains, chemicals, and solvents. Enamo Grip Clear should be used for graffiti protection.

Benefits:

Graffiti Protection

High-gloss, semi-gloss, satin finish

Self-leveling (no brush marks)

Pictured to the left are trains in Rome, Italy coated with Enamo Grip clear, covered with graffiti, then, and cleaned with SPI Graffiti Cleaner and washed and placed back into service.

Below, workers remove graffiti from the train door.


21st Century Solutions for 20th Century Challenges

150-Year Old Bridge

Australia

SPI Graffiti Cleaner used to remove existing graffiti prior to paint application. Enamo Grip Clear was applied as topcoat for future graffiti removal.



Italy Bus

Before and After

GRAFFITI CLEANER A bus in Italy, covered with an adhesive polyesther film, was coated with Enamo Grip Clear. The graffiti is easily removed when cleaned with SPI’s Graffiti Cleaner. The Graffiti Cleaner worked much faster than competing products, and the finished surface was left in pristine condition. SPI’s Graffiti Cleaner should be tested for compatibility with any surface being cleaned. Although Graffiti Cleaner is strong on graffiti, it did not harm the rubber seals around the windows and doors.

When the topcoat is Enamo Grip Clear, graffiti can easily be removed with SPI’s Graffiti Cleaner.



Texas School District

Reagan High School

Houston, Texas

Faculty at this school tried to remove existing graffiti from concrete walls but because the concrete is porous, the ink residue remained. After using SPI Graffiti Cleaner, the surface was wiped clear of all ink residues, the area repainted and then topcoated with Enamo Grip Clear. Enamo Grip works on concrete, steel, aluminum, masonry, fiberglass and other substrates.

ASTM D4060 TABER ABRASIONTESTING FOR

SUPERIOR PRODUCTS INTERNATIONAL IION

ENAMO GRIPVTEC #100-1558-2

TESTED: June 5, 2002

VIEC Laboratories I n c.

June 11, 2002

Client: Superior10835 w.

Shawnee,

Products International78th StreetKS 66214

II

Attention: Mr. J.E. pritchett

Test Method: This test was conducted in accordance with ASTMD4060; Taber Abrasion Resistance Measurements @standard temperature and humidity, using a TaberModel 502 Abrader ahd equipped with C-17 wheels and1,000 gram load.

Disclaimer: This is a factual report of the results obtained from the laboratory test of sampleproducts. The results may be applied only to the products tested and should not be construed asapplicable to other similar products of the manufacturer. The report is not a recommendation ordisapprobation by VTEC Laboratories, Inc. of the material tested. While this report may be used forobtaining product acceptance, it may not be used in advertising.

Notice: VTEC Laboratories Inc. will not be liable for any loss or damage resulting from the use of thedata in this report, in excess of the invoice. This report pertains to the sample tested only. Suchreport shall not be interpreted to be a warranty, either expressed or implied as to the suitability orfitness of said sample for such uses or applications, as the party contracting for the report may applysuch sample.

212 Manida Street ·Bronx, New York10474 ·(718) 542-8248 ·Fax: (718) 542-8759 ·www.vteclabs.comI .

VTEC#100-1558-2 Superior Products International II ASTM D4060

Results:

Test Number:

Test Date:

Load:Wheel:

Temperature:Relative Humidity:Apparatus Used:

100-1558-205 June 2002

1,000 gramsCS-17

74°F50%Taber Model 502 AbraderDenver A-250 Analytical Balance

NeLl{ Schul tzExecutive Director

Amirudin RahimTechnical Director

3

- .-

Enamo Grip Weight Abrasion Loss

Sample 1 (grams) (mg/100 revolutions)Wo 71.1918

W100 71.1798 12.0W200 71.1657 14.1W300 71.1515 14.2W400 71.1408 10.7W500 71.1297 11.1

Ava= 12.4

Enamo Grip Weight Abrasion Loss

Sample 2 (grams) (mg/100 revolutions)Wo 71.7216

W100 71.7121 9.5W200 71.7081 4.0W300 71.6876 20.5W400

. .... 71.6753 12.3W500 71.6655 9.8

Ava= 11.2

ASTM E 96 TESTING(WATER METHOD)

FORSUPERIOR PRODUCTS

ONENAMO-GRIP

VTEC 100-2052TESTED: OCTOBER 11 & 12, 2004

VTEC Labor.alories I n c. .

October 12, 2004

Client: Superior Products10835 W 78iliStreetShawnee, KS 66214

Attention: J.E. Pritchett

Scope: This report contains the reference to thepreparation and conditioning of sample, observation ofand post test observation data test results.

test method,material-, test

Test Method: This test was conducted in accordance with ASTM E 96

specification.

'This test method covers the determination of water vapor transmission(WVT) . of materials through which passage of water vapor may be 'ofimportance. In the Water Method, the test specimen was sealed to thetop of the cup containing distilled water and then placed in a test~

chamber at 90°F with a relative humidity of 50% for 24 hours. The cupswere weighed at the beginning and at the end of the 24-hour cycle todetermine how much water evaporated.

DISCLAIMER:

This is a factual report of the results obtained from the laboratorytest of sample products. The results may be applied only to theproducts tested and should not be construed as applicable to othersimilar products of the manufacturer. The report is not arecommendation or disapprobation by VTEC Laboratories, Inc. of thematerial tested. While this report maybe used for obtaining productacceptance, it may not be used in advertising.

Notice: VTEC LaboratoriesInc. will not be liable for any loss or damage resulting from the use of thedata in this report, in excess of the invoice. This report pertains to the sample tested only. Such reportshall not be interpreted to be a warranty, either expressed or implied as to the suitability or fitness ofsaid sample for such uses or applications, as the party contracting for the report may apply such sample.

212 Manida Street · Bronx,New York10474 · (718) 542-8248 · Fax: (718) 542-8759 · www.vteclabs.com

VTEC#100-2052

Material Tested:

1) Manufacturer:2) Product Description:

3) Color:4) Number of Specimens:.5) Surface:6) Material description:7) Date of selection:9) Test Method:

Test Results:

SUPERIOR PRODUCTS

Superior ProductsENAMO-GRIP applied at 9 mils wet toproduce 4 mils dry.White3Smooth

by Manufacturer and VTECSeptember 2004Water Method

Neil SchultzExecutive Director

\

Amirudin RahimTechnical Director

Sample Weight Weight Diameter of

Exposed saturatlon.1Thickness Before After Exposed Surface Surface Area PressureSamole # (mils) (arams) (arams) (inches) Wl..1!:l @90 F (in. Ha.)

1 4 239.3 239.0 3.1875 0.2217 1.42

Relative Humidity Relative Humidity Water Vapor PermeanceIn Chamber In cup Transmission perms

(RH In Decimal) (RH in Decimal) (arains/sa. ft. h.) (aralnslsa. ft. h. In. Ha)0.5 1 0.8701 1.2255

Sample Weight Weight Diameter of Exposed SaturationThickness Before After Exposed Surface Surface Area Pressure

Samol,:, # (mils) (arams) (arams) (inches) Wl..1!:l @ 90 F (in. Ha.)2 4 244.4 244.3 3.1875 0.2217 1.42

Relative Humidity Relative Humidity Water Vapor PermeanceIn Chamber In cup Transmission perms

. (RHIn Declman (RH In Deciman (aralns/sa. ft. h.) (aralns/sa. ft. h. In. Ha)0.5 1 0.2900 0.4085

I

Sample Weight Weight Diameter of Exposed SaturationThickness Before After Exposed Surface Surface Area Pressure

Samole # (mils) (arams) (arams) (inches) Wl..1!:l @ 90 F (in. Ha.)3 4 240.4 240.3 3.1875 0.2217 1.42

Relative Humidity Relative Humidity Water VapQr PermeanceIn Chamber In cup Transmission perms

(RH In Declman (RH In Declman (aralnslsa. ft. h.) (arainslsa. ft. h. In. Ha)0.5 1 0.2900 0.4085

AVERAGE PERMS: 0.6809

IHO A.653(16) TZSTXNGFOR

SUPERIOR PRODUCTS INTERNATIONAL II, INC.ON

ENAMO-GRIP IVTEC #100-1944-2

TESTED: APRXL 23 & MAY 11, 2004

H3 39Vd S8:\;11 :>311\ 69LSl;r9S1L

VTEC Laboratories I n (.

iv:ay 13. 2004

('lien:.. SupexiOI Products International II. Inc.10835 W.78~h StreetShawDee Mission, KS 66214

Attent.ion: Mr. J.E. Pr~tchett

Scope2- ~his report contains the reference to the testmethod 1 prepara+':io~, and ,::ondi tioning Qf sample,obs€:rvation of materi.:'J.l, test and post test:ob8ervatio~ data tesc results.

Test Method: This test \vas c:ond'..1cted in iO'ccordanc:e ,,:ithA.653(16) specific~ticn_

INO

~'hi S $ t:::an(1,;H;-d should be used '::0 me,15:Jre .:w.d de.5c.~ribe theP.l"G';;e:::t::..e8 I:)f mar:sria.l.5, ,[1.!'Qc1uct$, or as.=:emblies i11 re::;;ponse toheat and flame under controlled laboratory conditiQ~s and should:Jot J:.'e '.lsed co desc.ribeen:appraise riH? fire. l10zard or fire risk()f mar:.eJ:"ial Sf products, oz- a.'5seln.bl.1e.s w1der ac :ual firecondj. CiOt"J5. H()we\"e:r. ;n~.s~)lts of thi.s test may be ~sed <;,$elemen.ts of ~ fire :isk .:tsses~"m~J:1t :-~'hicf; t,,-kes into dcc:ount all;)f the {aecors ;,'.:t.i::.'h .?~:e pe.n::ine,"7.t :::0 an assessrr.ent of the fire.hazard of a pdr~icular end use.

pj.scl...illl4tr: This is a fa.CL'Jdl x:ep';'"'l~f sample products. The resu1cs may;'\c.:. .c;,:: ~onsr.r-'i.~'~~"ol\d .Z!B ~wpllcable tc.repo;:~t: is: nQ::: a rec-::'rt\:-nendati::..r.. '';'l.~ a

:"iH"'l'i~l t:e:S~ed. \;;hile t.his .':~PQ,n.:i'~.'.' ~'iOl. c.~ ~~.cld in ih1"F€:r"tising

.:..f tho:; t;",~'ult~, ,:,bl_.",i"I,:~l fl'<)I~ t.h", la}:.oL'<tt..o':::t le;;t..'0", app:'ie<:\ or,l~' C..: ni~ pr,';'A::;\:.!; cesr.ed and shouldo-::.ner sir:.i.~.~t'" ;..r~.:h.tct.s ::d; tr"A man\..Lzact.!.lre The

di"";;.pprc'cat:ie>',, b~' "./'TEC La.bora:",~iez. !nc. of t:t'.ema:/ b~ u:s?C f,,:; cb'::,~i~j:.ng pLoduct ~~cept.anc:~ it

NC!t:!~ \''T'E;:~' :",~bOI~(.t)r.l{!'~ J{,(" , \';~1.~ n~:t bt) l!Able t.::.:t. .",r.:/ :0$$ ;:;:f d.:ur::;gA :t'~Mul!:ir.g f:('om the: ...9.~f tr.u .;i~t.:A in t.."1is r..::~,(.1r:.:. in ',"~XCIE.$g .:t tr:.e in :,:.::.G:-'his- repr.-rt: p4?.tt\in.~ (;.0 t.:h~ satr:J:.l~ r;4!.sn:~d

'I:~''''', ~:u::h r.:;Jp<.I't' i.;t\.:\lj r't)~ b~ jnt'.~t'l}=~";'l~\ (.() ~)~ h ;;Jfc.~n~.i.~j::ti~.:" ~~.(r:de?Q~~d (:.)' i.JYlP).~tQ(l .?~; rl)tb;' :H:::~~ilit,;)... (it 'fir:'.\~~::; .;)t ~al"j :;:..:n".!;)16 tCt' 51).:;:-}) '.l~e; (.'~' ap~)41~a:..:..t':1'''B 49 the p~rt':'r' <:cn~.rac:r1r::g~':)= ~.t:~. f"p0z"', n1A~ appl"z' ::.~H~h ~~i}',\=.1~

212 Manida S1Tsst ·Bronx.New York10474 · 171S}542-8248 · Fax:(718) 542-8759 · www.vtaclabs,com

saUl 8311\ S9L8lP98TL

VTec 1t100-1944.2

PRODUCT:

SOURCE:DIMENSIONS:SPECIMENTHICKNESS:

SUPEFUOR PRODUCTS INTERNATIONAL II. INC. IMO A.6&3(16)

SUPERIOR PRODUCTS INTERNATIONAL II, INC.

IMO A.653(16) FLAME SPREAD OATA

Enamo Grip I, made up of 3 parts of the ba.se(batch 1318():3)mixed witt.,1 part ofthe Cl<ringagent (bat::;h082702), applied at a thickne$$ 01 9 mils wet (5 miis dry)

to 11 gage steel panel.SUPERIOR PRDDUCT$INTERNATIONAL II. INC.156 mm X 800 mm

5 mils dry Enamo Grip Ion 11 Ga. Steel plate.

VTEC #COLOR:AL FOIL?DATE:

10a-1944.2WhiteYes5/13/2004

OBSERVATIONS: Than~wae.no llnUSUa: I)ehav,or or dripping duiing ihe te!';t.

150 mm$$C.

200 mm.sec.

250 mm.tee.

300 mm.sec.

350 mm.sec::.

400 mm.sec.

CONCLUS:IONS~ The speci.mens provided met all requirements per IMOResolution A.6531161 for bulkhead, wall and ceiling linings.

t" j]. Q~Amirudin RahimTechnical Director

Neil'SchultzExecu~ive Director

E0 39\;1d

3

S8:t/! 83.L/\ E,9L82:P981L

SAMPLE 1 SAMPLE 2 SAMPLE 3 AVERAGE

NOl1irnp;ngingPilot iJame used? YES YES YES

Test Duration(min.) 10.00 10.00 '10.00 10.00

Healof Ignrtion (MJ/m2j N/A N/A N/A N/A

Heat of Susta.ined Burning at (MJIr'l'l2):150 mm N/A N/A N/A N/A200 mm N/A N/A N/A N/A250 mm N/A N!A N/A N/A300 mm N/A NfA N/A NiA350 mm N/A N/A N/A N/A400 mm N/A N!A N/A N/A

Sample Average: N/A N/A N/A N/ATime of EXIingui9hmant (min.) N/A N/A NIP. N/AD,stanceburned (rnm) N/A N/A N/A N/A

CnticalFlux at ExlingUls.hment(kWi(r}) N/A N/A NiA N/AT01alHeatRelease(M.)) 0.29 0.31 0.30 0.30

?eak HeatRelea:se(kW) 0.76 0.76 0.72 0.75

Heat lor Sustained Burning (MJ/IT.2) N/A N/A N/A N/A

Documents

ENAMO GRIP - Amazon Simple Storage Service · Enamo Grip is a super tough, two component self-leveling polyurethane enamel that can be tinted to any color to achieve high gloss results