EN GLOBAL WATERPROOFING SOLUTIONS SOLUTIONS ......2016/09/13 · RE-WATERPROOFING of a TERRACE without removing the old tiles: 6 1st STEP: carry out an alkaline cleansing with: 1

... page 2

GLOBALWATERPROOFING SOLUTIONSSOLUTIONS GLOBALESD’IMPERMÉABILISATIONSOLUÇÔES GLOBAISDE IMPERMEABILIZAÇÂO

F

EN

P

.... page 28

..... pagina 54

A DHESIVES AN D C HEMICA L PROD UC TSFOR C ONS TRUCTION

DURABILITYAND SAFETY

3

CONTENTS

PAGETERRACES and BALCONIES:How to waterproof and lay tiles quickly and ECONOMICALLY: 4

RE-WATERPROOFING of a TERRACE without removing the old tiles: 6

How to WATERPROOF, lay and repoint TILES in SHOWER TRAYS: 8

How to WATERPROOF, lay and repoint ROUNDED EDGES IN SHOWER TRAYS: 10

How to WATERPROOF a transitable FLAT ROOF without a tile finish: 12

How to WATERPROOF a SLOPING ROOF at a low cost: 14

FLAT ROOFS MADE OF THIN HOLLOW BRICK:how to re-waterproof it with CLEAR paint: 16

How to WATERPROOF cellars, lift shafts, etc. applying COUNTER PRESSURE: 18

CHANGING ROOMS and POOL SURFACES:how to waterproof and lay easily: 20

PUBLIC SWIMMING-POOL: how to do it PROPERLY 22

REPAIRING POOLS with WATER LEAKS, without removing the old tiles 24

FAÇADES: how to prevent RAINWATER from entering: 26

PAVING: how to protect them from water and oil stains: 27

TERRACES and BALCONIES: howto waterproof and layquickly and ECONOMICALLY.

4

1st STEP: make the base and slopes with quick, ready-dosed mortar: PAVIFORT 1

2nd STEP: allow to dry for at least 24 hours3rd STEP: for easy water-proofing of terraces or balconies,

use 100% waterproof, elastic mortar: HIDROELASTIC 2

4th STEP: apply a 1st coat of HIDROELASTIC with a brush, roller or notched trowel. 3

5th STEP: allow to dry for at least 4 hours

6th STEP: apply a 2nd coat of HIDROELASTIC in theopposition direction to the first one. 4

7th STEP: allow to dry completely for 24 to 36 hours 58th STEP: then lay the tiles using

a special cement adhesive forwaterproofed surfaces, such as: TECNOCOL FLEX 6

9th STEP: allow the shell to dry for at least 24 hours10th STEP: then, rejoint the paving

with a flexible, water-repellent product: EUROCOLOR FLEX or 7or one that is resistant to weak acids: JUNTATEC 7

11th STEP: make the necessary expansion joints with: SELLALASTIC 812th STEP: for perfect, clean, safe, long-lasting and

properly waterproofed terraces or balconies. 9

photoWATERPROOFING, LAYING and REPOINTING:

FOR MORE INFORMATION PLEASE CONSULT THE RESPECTIVE TECHNICAL SPECIFICATIONS

5

After 4 hours, apply a 2nd coatusing cross-cross strokes over thewhole surface. Increase the height15 cm on the lateral walls.

4

Leave the waterproofing to dryfor between 24 and 36 hoursbefore laying the ceramic tiles.

5

After mixing the TECNOCOLFLEX with water, lay the tiles usingthe double-gluing technique.

6

The HIDROELASTIC product ispre-dosed: mix all of the powderwith all of the liquid using anelectric mixer.

2

Apply a 1st coat with a brush,roller or notched trowel.

3

Form the mortar base of theterrace and gradients withquick-set mortar: PAVIFORT.

1

Rework the panels with a water-repellent mortar such asEUROCOLOR FLEX or mortarthat is resistant to weak acids,such as JUNTATEC.

7

Last of all, form the expansionjoints every 16-25 m2, usingSELLALASTIC.

8

You can now waterproof yourTERRACE easily and quicklywith HIDROELASTIC elastic,waterproofing mortar.

9

allow todry for

24 hours

allow todry for

24 hours

allow todry for4 hours

1st coat

2nd coat

RE-WATERPROOFING ofa TERRACE without removingthe old tiles:

6

1st STEP: carry out an alkaline cleansing with: 1 part FIX-SABO + 20 parts water: FIX-SABO 1

2nd STEP: rinse completely with clean water 23rd STEP: ALLOW TO DRY COMPLETELY 34th STEP: spread a fine coat of FIXMAX S2 over the old tiles. using a fine trowel. Do not exceed a thickness of 1 mm FIXMAX S2 4

5th STEP: leave this thin coat to dry: 24 hours

6th STEP: to re-waterproof the terrace easily,use HIDROELASTIC elastic 100%watertight mortar: apply a 1st coat with abrush, roller or fine trowel: HIDROELASTIC 5

7th STEP: allow to dry for at least 4 hours8th STEP: apply a 2nd coat of HIDROELASTIC in the

opposition direction to the first one. 6

9th STEP: allow to dry completely for 24 to 36 hours10th STEP: lay the new tiles over the waterproofing. Use the double application technique and press the tiles firmly: TECNOCOL FLEX 7

11th STEP: then grout the paving with a flexible, water-repellent, fungicide, smooth finish product: EUROCOLOR FLEX 812th STEP: Lastly, make the expansion joints with: SELLALASTIC 9



7

Spread a fine coat of FIXMAX S2over the old tiles. Use a notchedtrowel.

4

Apply a 1st coat of HIDROELASTICwith a brush, roller or notched trowel.Try not to leave a thickness greaterthan 1 mm.

5

Apply a 2nd coat of HIDROELASTICperpendicular to the 1st coat.

6

Then rinse walls and floor withplenty of clean water.

2

ALLOW TO DRY COMPLETELYFOR AS LONG AS NECESSARY.

3

carry out an alkaline cleansing with: 1 part FIX-SABÓ +20 parts water.

1

allow todry for

at least 4 hours

Use TECNOCOL FLEX or FIXARAPID FLEX cement to lay newtiles over the waterproofing. Adouble gluing application isnecessary.

7

Then work the joints again withEUROCOLOR FLEX.

Lastly make the perimeter expansion joints and work joints every16-20 m2 using SELLALASTICultra-elastic filler.

9

allow todry forat least4 hours

allow todry for24 to

36 hours

allow todry for

24 hours.

8

2nd coat1st coat

8

1st STEP: make the base and slopes withquick, ready-dosed mortar: PAVIFORT 1

2nd STEP: allow to dry for at least 24 hours3rd STEP: for easy water-proofing of terraces or

balconies, use 100% waterproof, elastic mortar: HIDROELASTIC 24th STEP: apply a 1st coat of HIDROELASTIC with

a brush, roller or notched trowel. 35th STEP: allow to dry for at least 4 hours

6th STEP: apply a 2nd coat of HIDROELASTIC in theopposition direction to the first one 4

7th STEP: allow to dry completely for 24 to 36 hours 58th STEP: then lay the tiles using a

special cement adhesive forwaterproofed surfaces, such as: TECNOCOL FLEX 6

9th STEP: allow the shell to dry for at least 24 hours10th STEP: then rejoint the paving

with a flexible, water-repellent product: EUROCOLOR FLEX or 7or a filler that is resistant to acids:: CERPOXI 7

11th STEP: make the necessary expansion joints with: SELLALASTIC 812th STEP: for perfect, clean, safe, long-lasting

and properly waterproofed shower trays. 9


How to WATERPROOF, glueand repoint TILES inSHOWER TRAYS:


9

After 4 hours, apply a 2nd coatusing cross strokes over the wholesurface. Increase the height 15cm at the lateral walls.

4


5


6


2

Apply a 1st coat with a brush,roller or notched trowel. Try notto leave a thickness greater than1 mm.

3

Form the mortar base of theshower tray and gradients withquick-set mortar:: RECRECEMPRE-MIX.

1

Rework the tray panels with water-repellent mortar such as EUROCOLOR FLEX or anti-acid fillersuch as CERPOXI.

7

Lastly, make the necessaryexpansion joints between theshower tray ceramic tiling andthe edge of the tray using SELLALASTIC elastic filler.

8

You can now waterproof yourshower tray easily and quicklywith HIDROELASTIC elastic,waterproofing mortar..

9

allow todry for

24 hours.

allow todry for

24 hours


1st coat

2nd coat

10

1st STEP: make the base and slopes with quick, ready-dosed mortar: PAVIFORT 12nd STEP: allow to dry for at least 24 hours3rd STEP: for easy water-proofing of terraces

or balconies, use 100% waterproof,elastic mortar: HIDROELASTIC 2

4th STEP: apply a 1st coat of HIDROELASTIC with a brush, roller or notched trowel 3





9th STEP: allow the shell to dry for at least 24 hours10th STEP: then rejoint the paving with

a flexible, water-repellent product : JUNTATEC or 7or a filler that is resistant to acids: CERPOXI 7

11th STEP: make the necessary expansion joints with: SELLALASTIC 812th STEP: for perfect, clean, safe, long-lasting and

properly waterproof round shower trays. 9


How to WATERPROOF, layand repoint ROUNDED EDGESin SHOWER TRAYS:


After 4 hours, apply a 2nd coatusing cross strokes over the wholesurface. Increase the height 15cm on the lateral walls.

4

Leave the waterproofing to dryfor between 24 and 36 hoursbefore laying the round edges.

5

After mixing TECNOCOL FLEXwith water, lay the round edgesusing a trowel of no more than6mm.

6


2


3

Form the mortar base of theshower tray and gradients withquick-set mortar:RECRECEM PRE-MIX.

1

Rework the tray panels withwater-repellent mortar such asJUNTATEC or anti-acid fillersuch as CERPOXI.

7

Lastly, make the necessaryexpansion joints between theshower tray ceramic tiling andthe edge of the tray using SELLALASTIC elastic filler.

8

You can now waterproof yourround shower tray easily andquickly with HIDROELASTICelastic, waterproofing mortar.

9

allow todry for

24 hours.

allow todry for

24 hours.


1st coat

2nd coat

11

How to WATERPROOF atransitable FLAT ROOFwithout a tile finish.

12

1st STEP: regularise the substrate withself-levelling mortar, in order touse, a posteriori, the leastamount of waterproofing paint: FIX-NIVEL 1

2nd STEP: allow to dry completely for 12-24 hours 23rd STEP: on damp or dusty substrates,

first apply a coat of FIXAQUA PRIMER filler. This is the only way to prevent damp from rising from the substrate: FIXAQUA PRIMER 3

4th STEP: leave to dry completely for at least 24 hoursin well-aired conditions

5th STEP: mix FIXAQUA FILM with an electric mixerfor 2 minutes: FIXAQUA FILM 4

6th STEP: application: paint the surface using a short-nap roller. 5

7th STEP: leave the paint to dry for at least 24 hours 8th STEP: extra protection: on flan roofs exposed to

the sun, we recommend applying a coat of: FIXAQUA TRANS 6

9th STEP: FIXAQUA FILM gives elastic and extremely long-lasting protection. 7

photoWATERPROOFING a TRANSITABLE FLAT ROOF:


13

WATERPROOFING: theFIXAQUA FILM with an electricmixer.

4

Application: use a short-naproller to apply minimum two layersof paint.

5 6

on damp or dusty substrates, firstapply a coat of FIXAQUAPRIMER.

3

Even the substrate with self-levelling mortar such as: FIX-NIVEL.

1

EXTRA PROTECTION againstU.V. solar radiation: only forareas exposed to strong sunlight,apply a final coat of FIXAQUATRANS.

ULTRA-elastic FIXAQUA FILMcan be used for waterproofingtransitable roofs with every guarantee.

7

allow todry for

24 hours.

Leave the regularising, levelling,patching to dry for 12 to 24 hoursbefore going on to the next step.

2

allow todry 24 hours

How to WATERPROOF aSLOPING ROOF at alow cost.

14

1st STEP: regularise the substrate withfine, creamy mortar in order to use,a posteriori, the least possibleamount of waterproofing paint: FIX-ENLUCIDO 1

2nd STEP: allow to dry completely for 24-48 hours 23rd STEP: Mix:

2 parts de water and 1 part FIX-TERRATSApply evenly over the whole surface: primer 3

4th STEP: allow to dry for no more than 24 hoursIn summer, the times must be reduced.

5th STEP: apply a base coast of FIX-TERRATS usinga roller, brush or pneumaticspraying system: FIX-TERRATS 4

6th STEP: while the first coat is still fresh,reinforce the waterproofing traction by inserting a: VELO-TERRATS-50 5

7th STEP: immediately apply a little more FIX-TERRATS to the fibreglass veil sheet 6

8th STEP: leave the paint to dry for no more than 24 hours 79th STEP: apply a 2nd coat of FIX-TERRATS in the final

colour of the waterproofing. 8

10th STEP: FIX-TERRATS can be used to waterproof rooftopsat low cost, provided the roofhas a gradient of over 1%. 9

photoWATERPROOFING a NON-TRANSITABLE SLOPING ROOF:


15

WATERPROOFING:: apply a1st coat of FIX-TERRATS with aroller, brush or airless system.

4

reinforcement: while the paintis still wet, insert a fibreglass sheetand...

5

...then soak the sheet with a littlemore FIX-TERRATS.

6

Mix 2 parts water and 1 part FIX-TERRATS: apply this primer evenly.

3

Regularise the substrate with fine,creamy mortar that is easy toapply such as: FIX-ENLUCIDO.

1

Leave the 1st coat to dry for nomore than 24 hours (in summerthe times are reduced)

7

Lastly apply, perpendicularly tothe 1st coat, a second coat ofFIX-TERRATS in the final colourof the waterproofing.

8

FIX-TERRATS is an inexpensivewaterproofing product fornon-transitable roofs withgradients of more than 1%.

9

allow todry for nomore than24 hours

Leave the regularising, levelling,patching to dry for 24 to 48 hoursbefore going on to the next step.

2

1st coat

2nd coat

end of 1st coat

immediately immediately

FLAT ROOFS MADE OF THIN HOLLOW BRICK:how to re-waterproof it withCLEAR paint.

16

1st STEP: the success of this application is achievedby thoroughly cleaning the existing brick.Remove all dead leaves and dirt: sweeping 1

2nd STEP: then clean the whole terrace. Mix: 1 part FIX-SABO detergent and 20 parts water andclean the terrace using a brush with nylon bristles: FIX-SABO 2

3rd STEP: rinse with plenty of water 24th STEP: leave to dry completely5th STEP: locate and repair all fissures,

cracks, flaking, etc. Also seal the joint between the sump pitand brick correctly: SELLADOR S10 3-4

6th STEP: leave to dry for 24-48 hours, depending on the climate7th STEP: waterproofing: pour the clear polyurethane

into a bucket and apply a 1st coatwith a short-haired wool roller: FIXAQUA TRANS 5-6

8th STEP: leave to dry for 5 to 24 hours, depending on the climate

9th STEP: Apply a 2nd coat , using criss-cross strokes, over the first coat. Apply as many coats as you wish. 7

10th STEP: FIXAQUA TRANS, allows you to re-waterproof,maintaining the original appearance. 8

photoRE-WATERPROOFING a ROOF with thin hollow brick:


17

... repair them with SELLADORS10 ultra-elastic filler.

4

Waterproofing: Pour theFIXAQUA TRANS clear paintinto a bucket and ...

5

Locate all fissures, cracks, flaking,leak points or sumps pits and ...

3

Sweep the whole surface thoroughly:in the event of any dirt remaining, thiswill stick to the waterproofing.

1

...apply a 1st coat with a short-haired wool roller.

6

Apply a 2nd coat of FIXAQUATRANS , using criss-cross strokes,over the first coat. Apply as manycoats as you wish.

7

FIXAQUA TRANS CLEAR elasticpolyurethane allows you to waterproof your roof, maintaining itsoriginal appearance.

8

allow todry 24-48 hours

Clean the whole terrace with FIX-SABO diluted with 20 parts waterand then rinse well with cleanwater.

allow todry between

5 and 24 hours

2

1st coat

2nd coat

leave todry completely

How to WATERPROOFcellars, lift shafts, etc.applying COUNTER PRESSURE.

18

1st STEP: waterproofing at counter pressurerequires the use of special mortar: It must be 100% waterproof, with maximum adherence and must remain strongly anchored to the substrate: HIDROFIX 3

2nd STEP: HIDROFIX is mixed only with water usingan electric mixer. The mixed product has the appearance of creamy paint. 4

3rd STEP: apply a1st coat at the maximum recommended thickness of 1mm. Use a roller, brush or pneumatic spraying system. 5

4th STEP: allow to dry completely for at least4 to 6 hours

5th STEP: apply 2nd coat using criss-cross strokes overthe first coat, so that the capillaryaction between both coats.Apply all the coats that are needed until no damp emerges. 6

6th STEP: leave to dry for several days before applying the final finish. This way, if any more damp stains appear, a final coatcan still be applied.

7th STEP: Finishes: paint can be applied over HIDROFIX or tilescan be laid over it with FIXSET FLEX as well as wood.

photoWATERPROOFING correctly at COUNTER PRESSURE:


19

...which, when mixed with justwater, is transformed into a paintthat is easy to apply using abrush, roller or airless system.

4

1st coat: apply a 1st coat with athickness of 1 mm, covering thewhole surface that is to be protected.

5

2nd coat: if necessary, apply asmany coats are required.

6

MIXING: to waterproof at counterpressure, use HIDROFIX mortar...

3

Cellars below the undergroundwater level are usually areas wherewater enters at counter pressure.

1

Paint can be applied overHIDROFIX , preferably witha water base.

Any type of tile can be laid overHIDROFIX, using FIXSET FLEXcement adhesive.

Wood or parquet flooring can belaid over HIDROFIX...

allow todry for

4-6 hours.

Lift shafts are also places wherewater can enter, as they reachconsiderable depths.

2

1st coat 2nd coat

POSSIBLE FINISHES AFTER WATERPROOFING AT COUNTER PRESSURE:

CHANGING ROOMS and POOLSURFACES: how to waterproofand lay easily.

20

1st STEP: regularise the substrate withquick, pre-dosed mortar:

- for FLOORS: PAVIFORT 1- for WALLS: FIX-REVOCO 1

2nd STEP: allow to dry for at least 24 hours3rd STEP: to easily waterproof changing rooms and

pool surfaces vertically or horizontally, use elastic, 100% waterproofed mortar: HIDROELASTIC 2

4th STEP: apply a 1st coat of HIDROELASTIC with a brush, roller or notched trowel 3





9th STEP: allow the shell to dry for at least 24 hours10th STEP: then rejoint the paving

with a flexible, water-repellent product: EUROCOLOR FLEX or 7or one that is resistant to weak acids: JUNTATEC 7

11th STEP: make the necessary expansion joints with: SELLALASTIC 812th STEP: for perfect, safe, long-lasting and properly

waterproofed pool surfaces or changing rooms. 9



21

After 4 hours, apply a 2nd coatusing criss-cross strokes over thewhole surface.

4


5


6

HIDROELASTIC product ispre-dosed: mix all of the powderwith all of the liquid using an electricmixer.

2


3

Regularise the walls and floorsusing FIX-REVOCO and/orRECRECEM PRE-MIX.

1

Rework the panels with a water-repellent mortar such asEUROCOLOR FLEX or mortarthat is resistant to weak acids,such as JUNTATEC.

7

Lastly, make the necessary expansionjoints between the ceramic tiling ofthe floor and walls using SELLALASTIC elastic filler.

8

You can now waterproof thewalls of your shower easily andquickly with HIDROELASTIC,waterproofing mortar.

9

allow todry for

24 hours.

allow todry for

24 hours.

allow todry for at

least4 hours

1st coat

2nd coat

1st STEP: how to avoid future leaks in the wall-plinth joins: FUGA-STOP 12nd STEP: how to bond new

concrete with dried concrete: BOND-COAT 23rd STEP: how to avoid leaks in the PVC wall-conduit: SELLADOR S10 3-44th STEP: how to render the walls: FIX-REVOCO 55thº STEP: how to construct the plinth of the pool’s structure: 1.- apply a Portland bonding: PRIMFIX +portland 6 2.- apply the mortar: RECRECEM PRE-MIX 76th STEP: how to waterproof the pool’s structure: HIDROELASTIC 8-97th STEP: carrying out the WATERPROOF TEST: fill the pool with water for one week and repair all the possible fissures that appear 108th STEP: how to lay tiles on the HIDROFIX waterproofing: TECNOCOL FLEX 11

9th STEP: how to rejoint properly: 1st option.- inexpensive grouting: FIXCOLOR 0/4 or 4/16 2nd option.-repointing that is water-repellent,

flexible and resistant to weak acids: JUNTATEC 12 10th STEP: allow the shell to dry for 5 - 7 days and enjoy your new pool in complete safety.

photoCONSTRUCTING A NEW PUBLIC SWIMMING-POOL

22

PUBLIC SWIMMING-POOL:how to do it PROPERLY


... and without letting the bed dry,pour and level the RECRECEMPRE-MIX mortar.

7

WATERPROOFING: apply a topcoat of HIDROELASTIC super-elastic mortar.

8

WATERPROOFING: apply asecond coat of HIDROELASTIC, using criss-cross strokes,over the first coat.

PAREDES: render the walls withthe pool mortar: FIX-REVOCO.

5

PLINTH: first apply a bed of mortarmade with 1 part Portland + 1 part PRIMFIX latex...

6

Once the primer is dry, apply SELLADOR S10 ultra-elastic filler.

4

empty the pooland leave to dry.

REPOINTING: use JUNTATEC,and allow THE ENTIRE SHELL todry for 5-7 days before re-fillingthe swimming-pool.

12

allow todry for

24-36 hours

Before pouring the new concreteover the dry concrete, apply BOND-COAT.

2

Seal all the plastic-concrete joints:1st apply IMPRIMACION SELLADOR S10.

3

ESSENTIAL: prevent futureleaks in wall-plinth joints withFUGA-STOP.

WATERTIGHTNESS TEST: forreasons of safety, now is the timeto check the correct waterproofingof the pool.

LAYING THE TILE: always useTECNOCOL FLEX cement.Make a double application.

1110

1

1st coat

9

2nd coat

test de watertightness

make the concreteplinth and let

it dry

allow todry for

1-4 hours

allow todry for

24 hours.

allow todry for

4-6 hours

23

REPAIRING POOLSwith WATER LEAKS, withoutremoving the old tiles:

24

1th STEP: carry out an acid cleaning with: 1 part GRESNET + 5 parts water: GRESNET 1

2th STEP: carry out an alkaline cleaning with: 1 part FIX-SABO + 20 parts water: FIX-SABO 2

3th STEP: rinse walls and floor with clean water. 34th STEP: ALLOW TO DRY COMPLETELY 45th STEP: grout with FIXMAX S2 using a fine trowel. you must insert the NET-MORTER-110 mesh. The final cement-mesh-cement thickness must not exceed 1 mm. FIXMAX S2 5-8

6thº STEP: allow the grouting to dry: 24 hours 9

7th STEP: how to re-waterproof the pool’s structure: HIDROELASTIC 10(easy to use and inexpensive)

8th STEP: lay the new glass mosaic or ceramic tiles with TECNOCOL FLEX. Use a notched trowel. Use the double application technique and/or press the tiles firmly: TECNOCOL FLEX 11

9th STEP: then rejoint the pool with a product that is water-repellent, flexible and resistant to weak acids: JUNTATEC 12

10th STEP: allow the shell to dry for 5 - 7 days and enjoy

your new pool again.

PhotoWATERPROOFING, LAYING and REPOINTING:


...the mesh is placed on the entiresurface of the pool (walls andbottom) and...

7

...immediately spread anotherfine coat of FIXMAX S2 until it iscompletely covered.

8

ALLOW THE CEMENT-MESH-CEMENT SHELL TO DRY FOR 24HOURS.

9

Spread a fine coat of FIXMAX S2over the old tiles. Use the finetrowel...

5

...and while it is still fresh, insertthe 10 mm x 10 mm NET-MORTER-110 mesh...

6

ALLOW TO DRY COMPLETELYFOR AS LONG AS NECESSARY.

4

allow todry dependingon the climate

Finally, grout with JUNTATECand allow THE ENTIRE SHELL todry for 5-7 days before re-fillingthe swimming-pool.

12

allow todry for

4-12 hours

Carry out an alkaline cleaningwith: 1 part FIX-SABO + 20 partswater.

2

Then rinse walls and floor withplenty of clean water.

3

Carry out an acid cleaning with:1 part GRESNET + 5 parts water.

1

WATERPROOFING: apply two coats of HIDROELASTIC with a finetrowel, roller or brush. Thick: 1 mm.per coat. Leave 4 hours betweenapplying one coat and the next.

Always use TECNOCOL FLEXto lay new tiles onto the waterproofing. A double gluing application is necessary.

1110

25

FAÇADES: how to preventRAINWATER from entering.

26

1st STEP: natural stone, mortar, concrete, single-layer,brick and other façades are usuallyhighly absorbent. Rainwater isabsorbed by this type of substrate,leading to damp inside homes.We must protect them. 1

2nd STEP: apply a 1st coat of clear waterproofing, using a varnishing roller.Completely saturate the substrate: FIX-WALL 2

3rd STEP: allow to dry for at least 24 hours 24th STEP: apply a 2nd coat of FIX-WALL.

Apply as many coats as you wish. 2

photoWATERPROOFING BRICK FAÇADES TO PROTECT THEM FROM THE RAIN


When it rains, absorbent elementssuch as exposed brick, becomesaturated, leading to damp insidehomes.

1

To prevent this, apply two coats ofFIX-WALL water-repellent liquiduntil the substrate is completelysaturated.

2

FIX-WALL makes the waterform tiny droplets on the surfacethat run downwards, withoutpenetrating into the substrate.

3

HOW TO WATERPROOF AN EXPOSED BRICK FAÇADE TO PROTECT IT FROM THE RAIN:

PAVING:how to protect them from

water and oil stains:

27

1st STEP: rustic paving is warm and natural,but often absorbent and easily stained.It must be protected against water and oil. 1

2nd STEP: firstly, remove all the dirtand white deposits using GRESNETcleaning acid mixed with 5 parts water. 2

3rd STEP: then rinse off with clean water. 24th STEP: leave to dry completely for approx. 7 days5th STEP: apply a 1st coat of clear waterproofing,

using a varnishing roller.Completely saturate the substrate with: FIX-OIL 3

6th STEP: allow to dry for at least 24 hours7th STEP: apply a 2nd coat of FIX-OIL.

Apply as many coats as you wish. 3

photoWATERPROOFING ABSORBENT PAVING:

PARA MÁS INFORMACIÓN, CONSULTAR LAS FICHAS TECNICAS CORRESPONDIENTES

Rustic paving is warm but sometimes it is also absorbent. It mustbe protected to prevent them frombecoming stained.

1

Firstly, clean with acid to removeall traces of efflorescence. UseGRESNET acid diluted in 5 partswater.

2

When the paving is completely dry,apply two coats of FIX-OIL liquidwater and oil repellent until thesubstrate is completely saturated.

3

rinse andleave to dryfor 7 days

HOW TO WATERPROOF PAVING TO PROTECT IT FROM WATER AND OIL STAINS:

Documents

EN GLOBAL WATERPROOFING SOLUTIONS SOLUTIONS ......2016/09/13 · RE-WATERPROOFING of a TERRACE without removing the old tiles: 6 1st STEP: carry out an alkaline cleansing with: 1