Upload
lauracarrion
View
252
Download
2
Embed Size (px)
Citation preview
8/10/2019 Emtm66 RS- 602.ppt
1/10
Via A. Pacinotti 57025 PIOMBINO Italy
Tel +39-0565 223439 Fx +39-0565261028e.Mail [email protected] www.sider.it
mailto:[email protected]:[email protected]8/10/2019 Emtm66 RS- 602.ppt
2/10
CHARACTERISTICS
Versati le and easy to use
Wide measu re range by the same Measure Head.
Mou ld measuring from 1 to 6 axis ( 3 each s ide )
Able for straight, cu rve, mult i taper parabol ic
mou lds
High accu racy + - 0.01 mm
Measure reading on l ine on the electron ic box
display
Measur ing un t i l 10 mou ld and sending the data to
the P.C. by radio or cable
Elaboration of th e measu re data by P.C. and
showing on graphic and table
Compar ison between m easure executed in
dif ferent t im eOval ity check for round mould
Rhomboid i ty check for squ are mould
Show ing o f the measure on 3D mould v iew.
Autocal ibrat ion
Print data and graph ic,
Data archiv eFoot Rol l al ignment ch eck
and many other features.
8/10/2019 Emtm66 RS- 602.ppt
3/10
COMPONENTS
MEASURE
HEAD
ELCTR.
BOX
NOTE
BOOK
PRINTER
BATT
CHARGER
FOOT ROLL
ALIGNM
DIAGONAL
DEVICE
8/10/2019 Emtm66 RS- 602.ppt
4/10
OPTIONS
SQUARE - RECT.
FOOT ROLL ALIGN
RHOMBOIDITY.
ROUND
8/10/2019 Emtm66 RS- 602.ppt
5/10
MEASUREMENT RANGE
ROUND
SQUARE
SIZES MEASUREMENT FEATURES
Billett - 100 to 200 Accuracy . + - 0.01 mm
Bloom - 200 to 350 Resolution . + - 0.005 mm
Rectangular - As required Repeatability. + - 0.01 mm
Round - Size 1 120 to 200Size 2 200 to 300
Size 3 300 to 400
or as required
8/10/2019 Emtm66 RS- 602.ppt
6/10
MEASURE
MEASURE HEAD ELECTR. BOX
FUNCTIONS :
- Electronic Box - Measure Head
-Functions on display: - Movable size adapters-Autotest - Guide rod
-Size selection - Able for Foot roll alignment
-Measure in Caliper Mode - Able for Diagonal device
- Mould measure Mode
- Measure axis indication
- Measure values on line show.
- Battery level indication
- Data trans. by radio or wire- . and many other
ADAPTERDISPLAY
MEASURE HEAD
ELECTRONIC BOX
8/10/2019 Emtm66 RS- 602.ppt
7/10
DATA MANAGEMENT
P.C. Software main functions-
-Drawing Editor
Mould data for the measures comparison
-Calibration
To check and set the Measure Head automatically by
radio
8/10/2019 Emtm66 RS- 602.ppt
8/10
Measure data elaboration-
- Table and graphic
-3D Representat ion
Left difference
Center difference
Graphic
Right measure
Center measure
Left measure
Measure point
Right difference
8/10/2019 Emtm66 RS- 602.ppt
9/10
-Mould info
Synthetic mould data info:
- Mould data
- Taper values
- RMSE values
-Measures compar ison
Compar ison between m easurer executed in d i f ferent t ime
8/10/2019 Emtm66 RS- 602.ppt
10/10
-Diagonal or Ovalisation
Rhomboidity check for square mould
Ovalisation check for round mould
- Measu res Arch ive and research