EKS4 Error Codes

GMK 5180EKS 4 Error Codes

Error Groups:

1 Sensors2 Digital Inputs3 Communication4 Kinematic5 Crane Program6 Display7 Miscellaneous8 Software9 Operation

SENSORS - Group 1 Component ComponentIdentitiy Errors:

1 Lift cylinder, piston side pressure 1 Identifier2 Lift cylinder, piston side pressure 2 Alive Counter (signal recognition)3 Lift cylinder, rod side pressure 3 Below measuring range tolerance4 Main boom angle A 4 Above measuring range tolerance5 Main boom angle B 5 Status byte6 Main boom length A 6 Check byte7 Main boom length B 7 Sensor A & B out of tolerance8 Telescope cylinder length A 8 Sensor switched off9 Telescope cylinder length B 9 Other errors

10 Jib horizintal angle reference A (PTJ)11 Jib offset angle B (PTJ)12 Jib cylinder, piston side pressure CAN Error13 Jib cylinder, rod side pressure 1 Bus State15 CAN channel 1 2 Receiver Warning Level >= 9616 CAN channel 2 3 Transmit Warning Level >= 9617 CAN channel 318 CAN channel 4 Comp. 1919 Tele 5 has exceeded comparison length tolerance 1 External length drum & internal20 Offset angle / Removable calibration angle sensor tele picture tolerance > 80 cm21 Comparison of ECOS length sensor with inner Comp. 21

drum is above acceptable tolerance 1 Internal length drum & ECOSlength sensor tolerance > 30 cm

DIGITAL INPUTS - Group 2

Component Component Identity: Errors:

1 In-position (pinning) 0 No error5 Main Hoist 1 Cable break7 Auxiliary Hoist 2 Short to ground

12 Boom pins 3 24V signal (this is not an error!)13 Telescope cylinder pin, left 4 Unstable signal14 Telescope cylinder pin, right 5 Dual inputs to central unit do

have equal values

EKS 4 Error Codes - EB/RC 24.06.99 Go Back

Grove Worldwide

Grove Worldwide

Grove Worldwide

Grove Worldwide

Grove Worldwide

Grove Worldwide

Grove Worldwide

Grove Worldwide

Grove Worldwide

COMMUNICATION - Group 3

Component ComponentIdentity: Errors:

1 Time 2 Alivecounter2 Tele picture 3 Comparison tele picture - ECOS 3 Tele request is out of tolerance6 Comparison tele picture 4 Checkbyte

Kinematic - Group 4

Component Component Identity Errors:

1 Sine 2 Deviation by 02 Cosine 9 Undefined3 Arc tangent5 Kinematics

CRANE PROGRAM - Group 5


1 Curve General:2 Swingaway lattice jib 2 not locked 4 Main Boom5 Load Charts Curve:6 Crane Type 4 Incorrect chart7 Derricking cylinder, jib

Main Boom / Swingaway lattice jib:

1 No rigging curve found3 Angle tolerance is too small /

Jib too steep4 Angle of main boom is too small5 No fixed curve found6 Angle of main boom is too big7 No variable curve found8 Angle tolerance is too big /

Jib too flat9 Differences are too big

(caculated to measured angle)

Load Charts: 4 Incorrect load charts

Crane Type:4 Incorrect crane type

Derricking Cylinder Jib:1 Force cylinder overload2 Load to high for derricking cylinder

EKS 4 Error Codes - EB/RC 24.06.99

DISPLAY - Group 6

Component Component Identity Errors:

1 Relay Group 12 Relay Group 2 Relay Group: 3 Digit 7 Relay not valid4 Led 8 Time out 5 Brightness6 Outrigger Front Fuse:7 Outrigger Rear Comp. 9 Group 18 A/D conversion 1 Fuse 19 Fuse group 1 2 Fuse 2

10 Fuse group 2 3 Fuse 311 ADC 0 4 Fuse 412 ADC 1 5 Fuse 513 ADC 2 6 Fuse 614 ADC 3 Fuse:15 ADC 4 Comp.10 Group 216 Beep 1 Fuse 717 Display board 2 Fuse 818 Input / output board 3 Fuse 9 19 Load level 4 Fuse 1020 Excess temperature 5 Fuse 11

6 Fuse 12

General 0 No error1 Input / output BUS ERROR2 Input / output ERROR3 Invalid4 Unstable signal5 Error during re - reading9 undefined

Comp. 20 6 Temperature display7 Temperature adapter


MISCELLANEOUS - Group 7


1 Extenal RAM test 1 General error2 External RAM test address 2 Address error3 Para Test 1, only with bridge 3 Check sum error4 Para Test 2 4 Low voltage5 I / O Bus test address 5 Incorrect data6 I / O Bus test data 6 Write protection cancelled7 Real time clock voltage 7 Time out8 Para 1 protect bit 8 Time out CP

10 Display board11 Voltage (5 volts)12 A/D converter13 Display board I / O error20 I / O board 21 V batt test22 I / O board I / O error23 Digital input test28 Calc parity29 Time32 RTC ERR33 WRPROT ERR

SOFTWARE - Group 8

Component Component Identity: Errors:

1 QSM 1 No evaluation 2 BUS error 3 Max. reading exceeded3 Aux error 4 Timeout4 VCC error 5 No bridge5 IO error6 VBAT error Comp. 6 7 Address error 4 Voltage remained

8 Illegal instruction9 PRIO VIO Comp. 20 - 23

10 TRAPCC TRAPV 1 Address error11 CHK CHK2 Instruct 2 Checksum 12 Division zero13 Trace14 Line 1011 EMU15 Line 1111 EMU16 Hardware BPT17 COPRO VIO18 No Handler19 Format err20 Parameter 1 Read21 Parameter 1 Write22 Parameter 2 Read23 Parameter 2 Write


OPERATON - Group 9


1 SLI Code 1 Data input2 Data Input 2 Confirm rigging code 3 By - Pass 3 Last data set4 Auto calibration 4 Data buffer full

5 Auto calibration released6 SLI by - passed


Errorcodes GMK5180 Version 1.4 Datum:2/21/2001

Errorcode Group Component Description1011 Sensors Pressure sensor 1, piston No response of pressure sensor 1, piston side of the derricking

cylinder.

1012 Sensors Pressure sensor 1 piston Internal error of pressure sensor, measured values are not updated.

1013 Sensors Pressure sensor 1, piston The value is below the measuring range tolerance

1014 Sensors Pressure sensor 1, piston The allowable maximum value has been exceeded.

1015 Sensors Pressure sensor 1, piston Pressure sensor indicated internal error.

1016 Sensors Pressure sensor 1, piston Data transmission error.

1017 Sensors Pressure sensor 1, piston The allowable pressure difference to sensor B (2) has been exceeded (max. 5 bar).

1018 Sensors Pressure sensor 1, piston The pressure sensor was manually switched off with keypad inputs at the central unit.

1019 Sensors Pressure sensor 1, pistion Undefined, basic function indicates error

1021 Sensors Pressure sensor 2, pistion No response of pressure sensor 2, piston side of the derricking cylinder.

1022 Sensors Pressure sensor 2, piston Internal pressure sensor error, measured values are not updated.

1023 Sensors Pressure sensor 2 pistion The value is below the measuring range tolerance.

1024 Sensors Pressure sensor 2, piston The allowable maximum value has been exceeded.

1025 Sensors Pressure sensor 2 pistion Pressure sensor indicates internal error.

1026 Sensors Pressure sensors 2, pistion Data transmission error.

1027 Sensors Pressure sensors 2, piston The allowable pressure difference to sensor A (1) has been exceeded (max. 5 bar).

1028 Sensors Pressure sensor 2, pistion The pressure sensor was manually switched off with keypad inputs at the central unit.

1029 Sensors Pressure senosr 2, pistion Undefined, basic function indicates error.

1031 Sensors Pressure sensor, rod side No response of the pressure sensor, rod side of the derricking cylinder.

1032 Sensors Pressure sensor, rod side Internal pressure sensor, measured values are not updated.

1033 Sensors Pressure sensor, rod side The value is below the measuring range tolerance.

1034 Sensors Pressure sensor, rod side The allowable maximum value has been exceeded.

1035 Sensors Pressure sensor, rod side Pressure sensor indicated internal error.

Page 1

Documents

EKS4 Error Codes